]>
Commit | Line | Data |
---|---|---|
1da177e4 | 1 | /* |
93c0b560 | 2 | * linux/drivers/ide/pci/trm290.c Version 1.05 Dec. 26, 2007 |
1da177e4 LT |
3 | * |
4 | * Copyright (c) 1997-1998 Mark Lord | |
93c0b560 | 5 | * Copyright (c) 2007 MontaVista Software, Inc. <source@mvista.com> |
1da177e4 LT |
6 | * May be copied or modified under the terms of the GNU General Public License |
7 | * | |
8 | * June 22, 2004 - get rid of check_region | |
59904159 | 9 | * - Jesper Juhl |
1da177e4 LT |
10 | * |
11 | */ | |
12 | ||
13 | /* | |
14 | * This module provides support for the bus-master IDE DMA function | |
15 | * of the Tekram TRM290 chip, used on a variety of PCI IDE add-on boards, | |
16 | * including a "Precision Instruments" board. The TRM290 pre-dates | |
17 | * the sff-8038 standard (ide-dma.c) by a few months, and differs | |
18 | * significantly enough to warrant separate routines for some functions, | |
19 | * while re-using others from ide-dma.c. | |
20 | * | |
21 | * EXPERIMENTAL! It works for me (a sample of one). | |
22 | * | |
23 | * Works reliably for me in DMA mode (READs only), | |
24 | * DMA WRITEs are disabled by default (see #define below); | |
25 | * | |
26 | * DMA is not enabled automatically for this chipset, | |
27 | * but can be turned on manually (with "hdparm -d1") at run time. | |
28 | * | |
29 | * I need volunteers with "spare" drives for further testing | |
30 | * and development, and maybe to help figure out the peculiarities. | |
31 | * Even knowing the registers (below), some things behave strangely. | |
32 | */ | |
33 | ||
34 | #define TRM290_NO_DMA_WRITES /* DMA writes seem unreliable sometimes */ | |
35 | ||
36 | /* | |
37 | * TRM-290 PCI-IDE2 Bus Master Chip | |
38 | * ================================ | |
39 | * The configuration registers are addressed in normal I/O port space | |
40 | * and are used as follows: | |
41 | * | |
42 | * trm290_base depends on jumper settings, and is probed for by ide-dma.c | |
43 | * | |
44 | * trm290_base+2 when WRITTEN: chiptest register (byte, write-only) | |
45 | * bit7 must always be written as "1" | |
46 | * bits6-2 undefined | |
47 | * bit1 1=legacy_compatible_mode, 0=native_pci_mode | |
48 | * bit0 1=test_mode, 0=normal(default) | |
49 | * | |
50 | * trm290_base+2 when READ: status register (byte, read-only) | |
51 | * bits7-2 undefined | |
52 | * bit1 channel0 busmaster interrupt status 0=none, 1=asserted | |
53 | * bit0 channel0 interrupt status 0=none, 1=asserted | |
54 | * | |
55 | * trm290_base+3 Interrupt mask register | |
56 | * bits7-5 undefined | |
57 | * bit4 legacy_header: 1=present, 0=absent | |
58 | * bit3 channel1 busmaster interrupt status 0=none, 1=asserted (read only) | |
59 | * bit2 channel1 interrupt status 0=none, 1=asserted (read only) | |
60 | * bit1 channel1 interrupt mask: 1=masked, 0=unmasked(default) | |
61 | * bit0 channel0 interrupt mask: 1=masked, 0=unmasked(default) | |
62 | * | |
63 | * trm290_base+1 "CPR" Config Pointer Register (byte) | |
64 | * bit7 1=autoincrement CPR bits 2-0 after each access of CDR | |
65 | * bit6 1=min. 1 wait-state posted write cycle (default), 0=0 wait-state | |
66 | * bit5 0=enabled master burst access (default), 1=disable (write only) | |
67 | * bit4 PCI DEVSEL# timing select: 1=medium(default), 0=fast | |
68 | * bit3 0=primary IDE channel, 1=secondary IDE channel | |
69 | * bits2-0 register index for accesses through CDR port | |
70 | * | |
71 | * trm290_base+0 "CDR" Config Data Register (word) | |
72 | * two sets of seven config registers, | |
73 | * selected by CPR bit 3 (channel) and CPR bits 2-0 (index 0 to 6), | |
74 | * each index defined below: | |
75 | * | |
76 | * Index-0 Base address register for command block (word) | |
77 | * defaults: 0x1f0 for primary, 0x170 for secondary | |
78 | * | |
79 | * Index-1 general config register (byte) | |
80 | * bit7 1=DMA enable, 0=DMA disable | |
81 | * bit6 1=activate IDE_RESET, 0=no action (default) | |
82 | * bit5 1=enable IORDY, 0=disable IORDY (default) | |
83 | * bit4 0=16-bit data port(default), 1=8-bit (XT) data port | |
84 | * bit3 interrupt polarity: 1=active_low, 0=active_high(default) | |
85 | * bit2 power-saving-mode(?): 1=enable, 0=disable(default) (write only) | |
86 | * bit1 bus_master_mode(?): 1=enable, 0=disable(default) | |
87 | * bit0 enable_io_ports: 1=enable(default), 0=disable | |
88 | * | |
89 | * Index-2 read-ahead counter preload bits 0-7 (byte, write only) | |
90 | * bits7-0 bits7-0 of readahead count | |
91 | * | |
92 | * Index-3 read-ahead config register (byte, write only) | |
93 | * bit7 1=enable_readahead, 0=disable_readahead(default) | |
94 | * bit6 1=clear_FIFO, 0=no_action | |
95 | * bit5 undefined | |
96 | * bit4 mode4 timing control: 1=enable, 0=disable(default) | |
97 | * bit3 undefined | |
98 | * bit2 undefined | |
99 | * bits1-0 bits9-8 of read-ahead count | |
100 | * | |
101 | * Index-4 base address register for control block (word) | |
102 | * defaults: 0x3f6 for primary, 0x376 for secondary | |
103 | * | |
104 | * Index-5 data port timings (shared by both drives) (byte) | |
105 | * standard PCI "clk" (clock) counts, default value = 0xf5 | |
106 | * | |
107 | * bits7-6 setup time: 00=1clk, 01=2clk, 10=3clk, 11=4clk | |
108 | * bits5-3 hold time: 000=1clk, 001=2clk, 010=3clk, | |
109 | * 011=4clk, 100=5clk, 101=6clk, | |
110 | * 110=8clk, 111=12clk | |
111 | * bits2-0 active time: 000=2clk, 001=3clk, 010=4clk, | |
112 | * 011=5clk, 100=6clk, 101=8clk, | |
113 | * 110=12clk, 111=16clk | |
114 | * | |
115 | * Index-6 command/control port timings (shared by both drives) (byte) | |
116 | * same layout as Index-5, default value = 0xde | |
117 | * | |
118 | * Suggested CDR programming for PIO mode0 (600ns): | |
119 | * 0x01f0,0x21,0xff,0x80,0x03f6,0xf5,0xde ; primary | |
120 | * 0x0170,0x21,0xff,0x80,0x0376,0xf5,0xde ; secondary | |
121 | * | |
122 | * Suggested CDR programming for PIO mode3 (180ns): | |
123 | * 0x01f0,0x21,0xff,0x80,0x03f6,0x09,0xde ; primary | |
124 | * 0x0170,0x21,0xff,0x80,0x0376,0x09,0xde ; secondary | |
125 | * | |
126 | * Suggested CDR programming for PIO mode4 (120ns): | |
127 | * 0x01f0,0x21,0xff,0x80,0x03f6,0x00,0xde ; primary | |
128 | * 0x0170,0x21,0xff,0x80,0x0376,0x00,0xde ; secondary | |
129 | * | |
130 | */ | |
131 | ||
1da177e4 LT |
132 | #include <linux/types.h> |
133 | #include <linux/module.h> | |
134 | #include <linux/kernel.h> | |
135 | #include <linux/mm.h> | |
136 | #include <linux/ioport.h> | |
137 | #include <linux/interrupt.h> | |
138 | #include <linux/blkdev.h> | |
139 | #include <linux/init.h> | |
140 | #include <linux/hdreg.h> | |
141 | #include <linux/pci.h> | |
142 | #include <linux/delay.h> | |
143 | #include <linux/ide.h> | |
144 | ||
145 | #include <asm/io.h> | |
146 | ||
147 | static void trm290_prepare_drive (ide_drive_t *drive, unsigned int use_dma) | |
148 | { | |
149 | ide_hwif_t *hwif = HWIF(drive); | |
150 | u16 reg = 0; | |
151 | unsigned long flags; | |
152 | ||
153 | /* select PIO or DMA */ | |
154 | reg = use_dma ? (0x21 | 0x82) : (0x21 & ~0x82); | |
155 | ||
156 | local_irq_save(flags); | |
157 | ||
158 | if (reg != hwif->select_data) { | |
159 | hwif->select_data = reg; | |
160 | /* set PIO/DMA */ | |
0ecdca26 BZ |
161 | outb(0x51 | (hwif->channel << 3), hwif->config_data + 1); |
162 | outw(reg & 0xff, hwif->config_data); | |
1da177e4 LT |
163 | } |
164 | ||
165 | /* enable IRQ if not probing */ | |
166 | if (drive->present) { | |
0ecdca26 | 167 | reg = inw(hwif->config_data + 3); |
1da177e4 LT |
168 | reg &= 0x13; |
169 | reg &= ~(1 << hwif->channel); | |
0ecdca26 | 170 | outw(reg, hwif->config_data + 3); |
1da177e4 LT |
171 | } |
172 | ||
173 | local_irq_restore(flags); | |
174 | } | |
175 | ||
176 | static void trm290_selectproc (ide_drive_t *drive) | |
177 | { | |
178 | trm290_prepare_drive(drive, drive->using_dma); | |
179 | } | |
180 | ||
93c0b560 | 181 | static void trm290_dma_exec_cmd(ide_drive_t *drive, u8 command) |
1da177e4 | 182 | { |
125e1874 | 183 | BUG_ON(HWGROUP(drive)->handler != NULL); /* paranoia check */ |
1da177e4 LT |
184 | ide_set_handler(drive, &ide_dma_intr, WAIT_CMD, NULL); |
185 | /* issue cmd to drive */ | |
0ecdca26 | 186 | outb(command, IDE_COMMAND_REG); |
1da177e4 LT |
187 | } |
188 | ||
93c0b560 | 189 | static int trm290_dma_setup(ide_drive_t *drive) |
1da177e4 LT |
190 | { |
191 | ide_hwif_t *hwif = drive->hwif; | |
192 | struct request *rq = hwif->hwgroup->rq; | |
193 | unsigned int count, rw; | |
194 | ||
195 | if (rq_data_dir(rq)) { | |
196 | #ifdef TRM290_NO_DMA_WRITES | |
197 | /* always use PIO for writes */ | |
198 | trm290_prepare_drive(drive, 0); /* select PIO xfer */ | |
199 | return 1; | |
200 | #endif | |
201 | rw = 1; | |
202 | } else | |
203 | rw = 2; | |
204 | ||
205 | if (!(count = ide_build_dmatable(drive, rq))) { | |
206 | /* try PIO instead of DMA */ | |
207 | trm290_prepare_drive(drive, 0); /* select PIO xfer */ | |
208 | return 1; | |
209 | } | |
210 | /* select DMA xfer */ | |
211 | trm290_prepare_drive(drive, 1); | |
0ecdca26 | 212 | outl(hwif->dmatable_dma | rw, hwif->dma_command); |
1da177e4 LT |
213 | drive->waiting_for_dma = 1; |
214 | /* start DMA */ | |
0ecdca26 | 215 | outw((count * 2) - 1, hwif->dma_status); |
1da177e4 LT |
216 | return 0; |
217 | } | |
218 | ||
93c0b560 | 219 | static void trm290_dma_start(ide_drive_t *drive) |
1da177e4 LT |
220 | { |
221 | } | |
222 | ||
223 | static int trm290_ide_dma_end (ide_drive_t *drive) | |
224 | { | |
225 | ide_hwif_t *hwif = HWIF(drive); | |
226 | u16 status = 0; | |
227 | ||
228 | drive->waiting_for_dma = 0; | |
229 | /* purge DMA mappings */ | |
230 | ide_destroy_dmatable(drive); | |
0ecdca26 | 231 | status = inw(hwif->dma_status); |
1da177e4 LT |
232 | return (status != 0x00ff); |
233 | } | |
234 | ||
235 | static int trm290_ide_dma_test_irq (ide_drive_t *drive) | |
236 | { | |
237 | ide_hwif_t *hwif = HWIF(drive); | |
238 | u16 status = 0; | |
239 | ||
0ecdca26 | 240 | status = inw(hwif->dma_status); |
1da177e4 LT |
241 | return (status == 0x00ff); |
242 | } | |
1da177e4 | 243 | |
93c0b560 SS |
244 | static void trm290_dma_host_on(ide_drive_t *drive) |
245 | { | |
246 | } | |
247 | ||
248 | static void trm290_dma_host_off(ide_drive_t *drive) | |
249 | { | |
250 | } | |
251 | ||
1da177e4 LT |
252 | static void __devinit init_hwif_trm290(ide_hwif_t *hwif) |
253 | { | |
254 | unsigned int cfgbase = 0; | |
255 | unsigned long flags; | |
256 | u8 reg = 0; | |
257 | struct pci_dev *dev = hwif->pci_dev; | |
258 | ||
1da177e4 LT |
259 | cfgbase = pci_resource_start(dev, 4); |
260 | if ((dev->class & 5) && cfgbase) { | |
261 | hwif->config_data = cfgbase; | |
262 | printk(KERN_INFO "TRM290: chip config base at 0x%04lx\n", | |
263 | hwif->config_data); | |
264 | } else { | |
265 | hwif->config_data = 0x3df0; | |
266 | printk(KERN_INFO "TRM290: using default config base at 0x%04lx\n", | |
267 | hwif->config_data); | |
268 | } | |
269 | ||
270 | local_irq_save(flags); | |
271 | /* put config reg into first byte of hwif->select_data */ | |
0ecdca26 | 272 | outb(0x51 | (hwif->channel << 3), hwif->config_data + 1); |
1da177e4 LT |
273 | /* select PIO as default */ |
274 | hwif->select_data = 0x21; | |
0ecdca26 | 275 | outb(hwif->select_data, hwif->config_data); |
1da177e4 | 276 | /* get IRQ info */ |
0ecdca26 | 277 | reg = inb(hwif->config_data + 3); |
1da177e4 LT |
278 | /* mask IRQs for both ports */ |
279 | reg = (reg & 0x10) | 0x03; | |
0ecdca26 | 280 | outb(reg, hwif->config_data + 3); |
1da177e4 LT |
281 | local_irq_restore(flags); |
282 | ||
283 | if ((reg & 0x10)) | |
284 | /* legacy mode */ | |
285 | hwif->irq = hwif->channel ? 15 : 14; | |
286 | else if (!hwif->irq && hwif->mate && hwif->mate->irq) | |
287 | /* sharing IRQ with mate */ | |
288 | hwif->irq = hwif->mate->irq; | |
289 | ||
290 | ide_setup_dma(hwif, (hwif->config_data + 4) ^ (hwif->channel ? 0x0080 : 0x0000), 3); | |
291 | ||
93c0b560 SS |
292 | hwif->dma_host_off = &trm290_dma_host_off; |
293 | hwif->dma_host_on = &trm290_dma_host_on; | |
294 | hwif->dma_setup = &trm290_dma_setup; | |
295 | hwif->dma_exec_cmd = &trm290_dma_exec_cmd; | |
296 | hwif->dma_start = &trm290_dma_start; | |
297 | hwif->ide_dma_end = &trm290_ide_dma_end; | |
298 | hwif->ide_dma_test_irq = &trm290_ide_dma_test_irq; | |
1da177e4 LT |
299 | |
300 | hwif->selectproc = &trm290_selectproc; | |
1da177e4 LT |
301 | #if 1 |
302 | { | |
303 | /* | |
304 | * My trm290-based card doesn't seem to work with all possible values | |
305 | * for the control basereg, so this kludge ensures that we use only | |
306 | * values that are known to work. Ugh. -ml | |
307 | */ | |
308 | u16 new, old, compat = hwif->channel ? 0x374 : 0x3f4; | |
309 | static u16 next_offset = 0; | |
310 | u8 old_mask; | |
311 | ||
0ecdca26 BZ |
312 | outb(0x54 | (hwif->channel << 3), hwif->config_data + 1); |
313 | old = inw(hwif->config_data); | |
1da177e4 | 314 | old &= ~1; |
0ecdca26 | 315 | old_mask = inb(old + 2); |
1da177e4 LT |
316 | if (old != compat && old_mask == 0xff) { |
317 | /* leave lower 10 bits untouched */ | |
318 | compat += (next_offset += 0x400); | |
319 | hwif->io_ports[IDE_CONTROL_OFFSET] = compat + 2; | |
0ecdca26 BZ |
320 | outw(compat | 1, hwif->config_data); |
321 | new = inw(hwif->config_data); | |
1da177e4 LT |
322 | printk(KERN_INFO "%s: control basereg workaround: " |
323 | "old=0x%04x, new=0x%04x\n", | |
324 | hwif->name, old, new & ~1); | |
325 | } | |
326 | } | |
327 | #endif | |
328 | } | |
329 | ||
85620436 | 330 | static const struct ide_port_info trm290_chipset __devinitdata = { |
1da177e4 LT |
331 | .name = "TRM290", |
332 | .init_hwif = init_hwif_trm290, | |
528a572d | 333 | .chipset = ide_trm290, |
7cab14a7 | 334 | .host_flags = IDE_HFLAG_NO_ATAPI_DMA | |
9ff6f72f | 335 | #if 0 /* play it safe for now */ |
7cab14a7 | 336 | IDE_HFLAG_TRUST_BIOS_FOR_DMA | |
9ff6f72f | 337 | #endif |
47b68788 | 338 | IDE_HFLAG_NO_AUTODMA | |
238e4f14 BZ |
339 | IDE_HFLAG_BOOTABLE | |
340 | IDE_HFLAG_NO_LBA48, | |
1da177e4 LT |
341 | }; |
342 | ||
343 | static int __devinit trm290_init_one(struct pci_dev *dev, const struct pci_device_id *id) | |
344 | { | |
345 | return ide_setup_pci_device(dev, &trm290_chipset); | |
346 | } | |
347 | ||
9cbcc5e3 BZ |
348 | static const struct pci_device_id trm290_pci_tbl[] = { |
349 | { PCI_VDEVICE(TEKRAM, PCI_DEVICE_ID_TEKRAM_DC290), 0 }, | |
1da177e4 LT |
350 | { 0, }, |
351 | }; | |
352 | MODULE_DEVICE_TABLE(pci, trm290_pci_tbl); | |
353 | ||
354 | static struct pci_driver driver = { | |
355 | .name = "TRM290_IDE", | |
356 | .id_table = trm290_pci_tbl, | |
357 | .probe = trm290_init_one, | |
358 | }; | |
359 | ||
82ab1eec | 360 | static int __init trm290_ide_init(void) |
1da177e4 LT |
361 | { |
362 | return ide_pci_register_driver(&driver); | |
363 | } | |
364 | ||
365 | module_init(trm290_ide_init); | |
366 | ||
367 | MODULE_AUTHOR("Mark Lord"); | |
368 | MODULE_DESCRIPTION("PCI driver module for Tekram TRM290 IDE"); | |
369 | MODULE_LICENSE("GPL"); |