]>
Commit | Line | Data |
---|---|---|
be5ce2f1 UKK |
1 | config LEDS_GPIO_REGISTER |
2 | bool | |
3 | help | |
4 | This option provides the function gpio_led_register_device. | |
5 | As this function is used by arch code it must not be compiled as a | |
6 | module. | |
7 | ||
66242f7e | 8 | menuconfig NEW_LEDS |
c72a1d60 RP |
9 | bool "LED Support" |
10 | help | |
a8d2e7d9 RP |
11 | Say Y to enable Linux LED support. This allows control of supported |
12 | LEDs from both userspace and optionally, by kernel events (triggers). | |
13 | ||
45d16f09 EM |
14 | if NEW_LEDS |
15 | ||
c72a1d60 | 16 | config LEDS_CLASS |
a403d930 | 17 | tristate "LED Class Support" |
c72a1d60 RP |
18 | help |
19 | This option enables the led sysfs class in /sys/class/leds. You'll | |
20 | need this to do anything useful with LEDs. If unsure, say N. | |
21 | ||
7aea8389 JA |
22 | config LEDS_CLASS_FLASH |
23 | tristate "LED Flash Class Support" | |
24 | depends on LEDS_CLASS | |
25 | help | |
26 | This option enables the flash led sysfs class in /sys/class/leds. | |
27 | It wrapps LED Class and adds flash LEDs specific sysfs attributes | |
28 | and kernel internal API to it. You'll need this to provide support | |
29 | for the flash related features of a LED device. It can be built | |
30 | as a module. | |
31 | ||
24f51e81 | 32 | comment "LED drivers" |
c3bc9956 | 33 | |
0a2f915b HZ |
34 | config LEDS_88PM860X |
35 | tristate "LED Support for Marvell 88PM860x PMIC" | |
0bae35e1 | 36 | depends on LEDS_CLASS |
37814fdc | 37 | depends on MFD_88PM860X |
0a2f915b HZ |
38 | help |
39 | This option enables support for on-chip LED drivers found on Marvell | |
40 | Semiconductor 88PM8606 PMIC. | |
41 | ||
49c34b8e JA |
42 | config LEDS_AAT1290 |
43 | tristate "LED support for the AAT1290" | |
44 | depends on LEDS_CLASS_FLASH | |
58d1809b | 45 | depends on V4L2_FLASH_LED_CLASS || !V4L2_FLASH_LED_CLASS |
6e3956cd | 46 | depends on GPIOLIB || COMPILE_TEST |
49c34b8e | 47 | depends on OF |
ac69b903 | 48 | depends on PINCTRL |
49c34b8e JA |
49 | help |
50 | This option enables support for the LEDs on the AAT1290. | |
51 | ||
fd7b025a ÁFR |
52 | config LEDS_BCM6328 |
53 | tristate "LED Support for Broadcom BCM6328" | |
54 | depends on LEDS_CLASS | |
522f17e1 | 55 | depends on HAS_IOMEM |
fd7b025a ÁFR |
56 | depends on OF |
57 | help | |
58 | This option enables support for LEDs connected to the BCM6328 | |
59 | LED HW controller accessed via MMIO registers. | |
60 | ||
589fca16 ÁFR |
61 | config LEDS_BCM6358 |
62 | tristate "LED Support for Broadcom BCM6358" | |
63 | depends on LEDS_CLASS | |
522f17e1 | 64 | depends on HAS_IOMEM |
589fca16 ÁFR |
65 | depends on OF |
66 | help | |
67 | This option enables support for LEDs connected to the BCM6358 | |
68 | LED HW controller accessed via MMIO registers. | |
69 | ||
b1e6b706 SKS |
70 | config LEDS_LM3530 |
71 | tristate "LCD Backlight driver for LM3530" | |
72 | depends on LEDS_CLASS | |
73 | depends on I2C | |
74 | help | |
75 | This option enables support for the LCD backlight using | |
76 | LM3530 ambient light sensor chip. This ALS chip can be | |
77 | controlled manually or using PWM input or using ambient | |
78 | light automatically. | |
79 | ||
401dea7f JH |
80 | config LEDS_LM3533 |
81 | tristate "LED support for LM3533" | |
82 | depends on LEDS_CLASS | |
83 | depends on MFD_LM3533 | |
84 | help | |
85 | This option enables support for the LEDs on National Semiconductor / | |
86 | TI LM3533 Lighting Power chips. | |
87 | ||
88 | The LEDs can be controlled directly, through PWM input, or by the | |
89 | ambient-light-sensor interface. The chip supports | |
90 | hardware-accelerated blinking with maximum on and off periods of 9.8 | |
91 | and 77 seconds respectively. | |
92 | ||
8b7cfbec SJ |
93 | config LEDS_LM3642 |
94 | tristate "LED support for LM3642 Chip" | |
95 | depends on LEDS_CLASS && I2C | |
96 | select REGMAP_I2C | |
97 | help | |
98 | This option enables support for LEDs connected to LM3642. | |
99 | The LM3642 is a 4MHz fixed-frequency synchronous boost | |
100 | converter plus 1.5A constant current driver for a high-current | |
101 | white LED. | |
102 | ||
103 | ||
4d3cb354 RP |
104 | config LEDS_LOCOMO |
105 | tristate "LED Support for Locomo device" | |
0bae35e1 | 106 | depends on LEDS_CLASS |
d09e1666 | 107 | depends on SHARP_LOCOMO |
4d3cb354 RP |
108 | help |
109 | This option enables support for the LEDs on Sharp Locomo. | |
110 | Zaurus models SL-5500 and SL-5600. | |
111 | ||
ac67e23b PS |
112 | config LEDS_MIKROTIK_RB532 |
113 | tristate "LED Support for Mikrotik Routerboard 532" | |
0bae35e1 | 114 | depends on LEDS_CLASS |
d09e1666 | 115 | depends on MIKROTIK_RB532 |
ac67e23b PS |
116 | help |
117 | This option enables support for the so called "User LED" of | |
118 | Mikrotik's Routerboard 532. | |
119 | ||
54bdc470 BD |
120 | config LEDS_S3C24XX |
121 | tristate "LED Support for Samsung S3C24XX GPIO LEDs" | |
0bae35e1 | 122 | depends on LEDS_CLASS |
b130d5c2 | 123 | depends on ARCH_S3C24XX |
54bdc470 BD |
124 | help |
125 | This option enables support for LEDs connected to GPIO lines | |
126 | on Samsung S3C24XX series CPUs, such as the S3C2410 and S3C2440. | |
127 | ||
1a87d942 CB |
128 | config LEDS_NET48XX |
129 | tristate "LED Support for Soekris net48xx series Error LED" | |
0bae35e1 | 130 | depends on LEDS_CLASS |
d09e1666 | 131 | depends on SCx200_GPIO |
1a87d942 CB |
132 | help |
133 | This option enables support for the Soekris net4801 and net4826 error | |
134 | LED. | |
135 | ||
3b2e46f8 RW |
136 | config LEDS_FSG |
137 | tristate "LED Support for the Freecom FSG-3" | |
0bae35e1 | 138 | depends on LEDS_CLASS |
d09e1666 | 139 | depends on MACH_FSG |
3b2e46f8 RW |
140 | help |
141 | This option enables support for the LEDs on the Freecom FSG-3. | |
142 | ||
0d75565f KK |
143 | config LEDS_WRAP |
144 | tristate "LED Support for the WRAP series LEDs" | |
0bae35e1 | 145 | depends on LEDS_CLASS |
d09e1666 | 146 | depends on SCx200_GPIO |
0d75565f KK |
147 | help |
148 | This option enables support for the PCEngines WRAP programmable LEDs. | |
149 | ||
f3b6b6cd YY |
150 | config LEDS_COBALT_QUBE |
151 | tristate "LED Support for the Cobalt Qube series front LED" | |
0bae35e1 | 152 | depends on LEDS_CLASS |
d09e1666 | 153 | depends on MIPS_COBALT |
2fea6f35 | 154 | help |
f3b6b6cd | 155 | This option enables support for the front LED on Cobalt Qube series |
2fea6f35 | 156 | |
97da7aaf YY |
157 | config LEDS_COBALT_RAQ |
158 | bool "LED Support for the Cobalt Raq series" | |
ec149619 | 159 | depends on LEDS_CLASS=y && MIPS_COBALT |
97da7aaf YY |
160 | select LEDS_TRIGGERS |
161 | help | |
162 | This option enables support for the Cobalt Raq series LEDs. | |
163 | ||
5843492c DM |
164 | config LEDS_SUNFIRE |
165 | tristate "LED support for SunFire servers." | |
0bae35e1 | 166 | depends on LEDS_CLASS |
d09e1666 | 167 | depends on SPARC64 |
5843492c DM |
168 | select LEDS_TRIGGERS |
169 | help | |
170 | This option enables support for the Left, Middle, and Right | |
171 | LEDs on the I/O and CPU boards of SunFire UltraSPARC servers. | |
172 | ||
4da498fc LW |
173 | config LEDS_IPAQ_MICRO |
174 | tristate "LED Support for the Compaq iPAQ h3xxx" | |
35bfe456 | 175 | depends on LEDS_CLASS |
4da498fc LW |
176 | depends on MFD_IPAQ_MICRO |
177 | help | |
178 | Choose this option if you want to use the notification LED on | |
179 | Compaq/HP iPAQ h3100 and h3600. | |
180 | ||
d39a7a63 KE |
181 | config LEDS_HP6XX |
182 | tristate "LED Support for the HP Jornada 6xx" | |
0bae35e1 | 183 | depends on LEDS_CLASS |
d09e1666 | 184 | depends on SH_HP6XX |
d39a7a63 | 185 | help |
692105b8 | 186 | This option enables LED support for the handheld |
d39a7a63 KE |
187 | HP Jornada 620/660/680/690. |
188 | ||
e14fa824 RV |
189 | config LEDS_PCA9532 |
190 | tristate "LED driver for PCA9532 dimmer" | |
0bae35e1 | 191 | depends on LEDS_CLASS |
5e0b080d | 192 | depends on I2C && INPUT |
e14fa824 RV |
193 | help |
194 | This option enables support for NXP pca9532 | |
692105b8 | 195 | LED controller. It is generally only useful |
e14fa824 RV |
196 | as a platform driver |
197 | ||
3c1ab50d JE |
198 | config LEDS_PCA9532_GPIO |
199 | bool "Enable GPIO support for PCA9532" | |
200 | depends on LEDS_PCA9532 | |
201 | depends on GPIOLIB | |
202 | help | |
203 | Allow unused pins on PCA9532 to be used as gpio. | |
204 | ||
205 | To use a pin as gpio pca9532_type in pca9532_platform data needs to | |
206 | set to PCA9532_TYPE_GPIO. | |
207 | ||
22e03f3b RA |
208 | config LEDS_GPIO |
209 | tristate "LED Support for GPIO connected LEDs" | |
0bae35e1 | 210 | depends on LEDS_CLASS |
9ab1963d | 211 | depends on GPIOLIB || COMPILE_TEST |
22e03f3b RA |
212 | help |
213 | This option enables support for the LEDs connected to GPIO | |
214 | outputs. To be useful the particular board must have LEDs | |
a7d878af TP |
215 | and they must be connected to the GPIO lines. The LEDs must be |
216 | defined as platform devices and/or OpenFirmware platform devices. | |
217 | The code to use these bindings can be selected below. | |
218 | ||
5054d39e AO |
219 | config LEDS_LP3944 |
220 | tristate "LED Support for N.S. LP3944 (Fun Light) I2C chip" | |
0bae35e1 | 221 | depends on LEDS_CLASS |
d09e1666 | 222 | depends on I2C |
5054d39e | 223 | help |
7f1be819 AO |
224 | This option enables support for LEDs connected to the National |
225 | Semiconductor LP3944 Lighting Management Unit (LMU) also known as | |
226 | Fun Light Chip. | |
5054d39e AO |
227 | |
228 | To compile this driver as a module, choose M here: the | |
229 | module will be called leds-lp3944. | |
230 | ||
c93d08fa | 231 | config LEDS_LP55XX_COMMON |
33b3a561 KM |
232 | tristate "Common Driver for TI/National LP5521/5523/55231/5562/8501" |
233 | depends on LEDS_LP5521 || LEDS_LP5523 || LEDS_LP5562 || LEDS_LP8501 | |
10c06d17 | 234 | select FW_LOADER |
2338f73d | 235 | select FW_LOADER_USER_HELPER |
c93d08fa | 236 | help |
33b3a561 | 237 | This option supports common operations for LP5521/5523/55231/5562/8501 |
c93d08fa MWK |
238 | devices. |
239 | ||
f4920f67 SO |
240 | config LEDS_LP5521 |
241 | tristate "LED Support for N.S. LP5521 LED driver chip" | |
242 | depends on LEDS_CLASS && I2C | |
c93d08fa | 243 | select LEDS_LP55XX_COMMON |
f4920f67 SO |
244 | help |
245 | If you say yes here you get support for the National Semiconductor | |
246 | LP5521 LED driver. It is 3 channel chip with programmable engines. | |
247 | Driver provides direct control via LED class and interface for | |
248 | programming the engines. | |
249 | ||
250 | config LEDS_LP5523 | |
ca705321 | 251 | tristate "LED Support for TI/National LP5523/55231 LED driver chip" |
f4920f67 | 252 | depends on LEDS_CLASS && I2C |
c93d08fa | 253 | select LEDS_LP55XX_COMMON |
f4920f67 | 254 | help |
ca705321 KM |
255 | If you say yes here you get support for TI/National Semiconductor |
256 | LP5523/55231 LED driver. | |
257 | It is 9 channel chip with programmable engines. | |
f4920f67 SO |
258 | Driver provides direct control via LED class and interface for |
259 | programming the engines. | |
260 | ||
ff45262a KM |
261 | config LEDS_LP5562 |
262 | tristate "LED Support for TI LP5562 LED driver chip" | |
263 | depends on LEDS_CLASS && I2C | |
264 | select LEDS_LP55XX_COMMON | |
265 | help | |
266 | If you say yes here you get support for TI LP5562 LED driver. | |
267 | It is 4 channels chip with programmable engines. | |
268 | Driver provides direct control via LED class and interface for | |
269 | programming the engines. | |
270 | ||
33b3a561 KM |
271 | config LEDS_LP8501 |
272 | tristate "LED Support for TI LP8501 LED driver chip" | |
273 | depends on LEDS_CLASS && I2C | |
274 | select LEDS_LP55XX_COMMON | |
275 | help | |
276 | If you say yes here you get support for TI LP8501 LED driver. | |
277 | It is 9 channel chip with programmable engines. | |
278 | Driver provides direct control via LED class and interface for | |
279 | programming the engines. | |
280 | It is similar as LP5523, but output power selection is available. | |
281 | And register layout and engine program schemes are different. | |
282 | ||
eb80411b KM |
283 | config LEDS_LP8788 |
284 | tristate "LED support for the TI LP8788 PMIC" | |
285 | depends on LEDS_CLASS | |
286 | depends on MFD_LP8788 | |
287 | help | |
288 | This option enables support for the Keyboard LEDs on the LP8788 PMIC. | |
289 | ||
7a8685ac DM |
290 | config LEDS_LP8860 |
291 | tristate "LED support for the TI LP8860 4 channel LED driver" | |
2969bb18 AL |
292 | depends on LEDS_CLASS && I2C |
293 | select REGMAP_I2C | |
7a8685ac DM |
294 | help |
295 | If you say yes here you get support for the TI LP8860 4 channel | |
296 | LED driver. | |
297 | This option enables support for the display cluster LEDs | |
298 | on the LP8860 4 channel LED driver using the I2C communication | |
299 | bus. | |
300 | ||
cec035de | 301 | config LEDS_CLEVO_MAIL |
95dc5768 | 302 | tristate "Mail LED on Clevo notebook" |
0bae35e1 | 303 | depends on LEDS_CLASS |
d09e1666 | 304 | depends on X86 && SERIO_I8042 && DMI |
cec035de MN |
305 | help |
306 | This driver makes the mail LED accessible from userspace | |
307 | programs through the leds subsystem. This LED have three | |
308 | known mode: off, blink at 0.5Hz and blink at 1Hz. | |
309 | ||
92e015cb MN |
310 | The driver supports two kinds of interface: using ledtrig-timer |
311 | or through /sys/class/leds/clevo::mail/brightness. As this LED | |
312 | cannot change it's brightness it blinks instead. The brightness | |
313 | value 0 means off, 1..127 means blink at 0.5Hz and 128..255 means | |
314 | blink at 1Hz. | |
cec035de MN |
315 | |
316 | This module can drive the mail LED for the following notebooks: | |
317 | ||
b3ba31f8 | 318 | Clevo D400P |
cec035de MN |
319 | Clevo D410J |
320 | Clevo D410V | |
321 | Clevo D400V/D470V (not tested, but might work) | |
322 | Clevo M540N | |
323 | Clevo M5x0N (not tested, but might work) | |
324 | Positivo Mobile (Clevo M5x0V) | |
325 | ||
b3ba31f8 | 326 | If your model is not listed here you can try the "nodetect" |
692105b8 | 327 | module parameter. |
b3ba31f8 | 328 | |
cec035de MN |
329 | To compile this driver as a module, choose M here: the |
330 | module will be called leds-clevo-mail. | |
331 | ||
f46e9203 NC |
332 | config LEDS_PCA955X |
333 | tristate "LED Support for PCA955x I2C chips" | |
0bae35e1 | 334 | depends on LEDS_CLASS |
d09e1666 | 335 | depends on I2C |
f46e9203 NC |
336 | help |
337 | This option enables support for LEDs connected to PCA955x | |
338 | LED driver chips accessed via the I2C bus. Supported | |
339 | devices include PCA9550, PCA9551, PCA9552, and PCA9553. | |
340 | ||
56a1740c | 341 | config LEDS_PCA963X |
af67384f | 342 | tristate "LED support for PCA963x I2C chip" |
75cb2e1d PM |
343 | depends on LEDS_CLASS |
344 | depends on I2C | |
345 | help | |
af67384f RRD |
346 | This option enables support for LEDs connected to the PCA963x |
347 | LED driver chip accessed via the I2C bus. Supported | |
348 | devices include PCA9633 and PCA9634 | |
75cb2e1d | 349 | |
c746b551 MB |
350 | config LEDS_WM831X_STATUS |
351 | tristate "LED support for status LEDs on WM831x PMICs" | |
0bae35e1 | 352 | depends on LEDS_CLASS |
d09e1666 | 353 | depends on MFD_WM831X |
c746b551 MB |
354 | help |
355 | This option enables support for the status LEDs of the WM831x | |
356 | series of PMICs. | |
357 | ||
0081e802 MB |
358 | config LEDS_WM8350 |
359 | tristate "LED Support for WM8350 AudioPlus PMIC" | |
0bae35e1 | 360 | depends on LEDS_CLASS |
d09e1666 | 361 | depends on MFD_WM8350 |
0081e802 MB |
362 | help |
363 | This option enables support for LEDs driven by the Wolfson | |
364 | Microelectronics WM8350 AudioPlus PMIC. | |
365 | ||
9e84561c MR |
366 | config LEDS_DA903X |
367 | tristate "LED Support for DA9030/DA9034 PMIC" | |
0bae35e1 | 368 | depends on LEDS_CLASS |
d09e1666 | 369 | depends on PMIC_DA903X |
9e84561c MR |
370 | help |
371 | This option enables support for on-chip LED drivers found | |
372 | on Dialog Semiconductor DA9030/DA9034 PMICs. | |
373 | ||
5ba73631 DDC |
374 | config LEDS_DA9052 |
375 | tristate "Dialog DA9052/DA9053 LEDS" | |
376 | depends on LEDS_CLASS | |
377 | depends on PMIC_DA9052 | |
378 | help | |
379 | This option enables support for on-chip LED drivers found | |
380 | on Dialog Semiconductor DA9052-BC and DA9053-AA/Bx PMICs. | |
381 | ||
ac2dd0f1 GL |
382 | config LEDS_DAC124S085 |
383 | tristate "LED Support for DAC124S085 SPI DAC" | |
0bae35e1 | 384 | depends on LEDS_CLASS |
d09e1666 | 385 | depends on SPI |
ac2dd0f1 GL |
386 | help |
387 | This option enables support for DAC124S085 SPI DAC from NatSemi, | |
388 | which can be used to control up to four LEDs. | |
389 | ||
41c42ff5 LF |
390 | config LEDS_PWM |
391 | tristate "PWM driven LED Support" | |
0bae35e1 | 392 | depends on LEDS_CLASS |
ad0ba85f | 393 | depends on PWM |
41c42ff5 LF |
394 | help |
395 | This option enables support for pwm driven LEDs | |
396 | ||
d4cc6a2e AO |
397 | config LEDS_REGULATOR |
398 | tristate "REGULATOR driven LED support" | |
0bae35e1 | 399 | depends on LEDS_CLASS |
d09e1666 | 400 | depends on REGULATOR |
d4cc6a2e AO |
401 | help |
402 | This option enables support for regulator driven LEDs. | |
403 | ||
0b56129b KK |
404 | config LEDS_BD2802 |
405 | tristate "LED driver for BD2802 RGB LED" | |
0bae35e1 | 406 | depends on LEDS_CLASS |
d09e1666 | 407 | depends on I2C |
0b56129b KK |
408 | help |
409 | This option enables support for BD2802GU RGB LED driver chips | |
410 | accessed via the I2C bus. | |
411 | ||
a328e95b DH |
412 | config LEDS_INTEL_SS4200 |
413 | tristate "LED driver for Intel NAS SS4200 series" | |
0bae35e1 | 414 | depends on LEDS_CLASS |
d09e1666 | 415 | depends on PCI && DMI |
a328e95b DH |
416 | help |
417 | This option enables support for the Intel SS4200 series of | |
418 | Network Attached Storage servers. You may control the hard | |
419 | drive or power LEDs on the front panel. Using this driver | |
420 | can stop the front LED from blinking after startup. | |
421 | ||
a8dd18fe DM |
422 | config LEDS_LT3593 |
423 | tristate "LED driver for LT3593 controllers" | |
0bae35e1 | 424 | depends on LEDS_CLASS |
82322741 | 425 | depends on GPIOLIB || COMPILE_TEST |
a8dd18fe DM |
426 | help |
427 | This option enables support for LEDs driven by a Linear Technology | |
428 | LT3593 controller. This controller uses a special one-wire pulse | |
429 | coding protocol to set the brightness. | |
430 | ||
ed4a10b4 MH |
431 | config LEDS_ADP5520 |
432 | tristate "LED Support for ADP5520/ADP5501 PMIC" | |
0bae35e1 | 433 | depends on LEDS_CLASS |
d09e1666 | 434 | depends on PMIC_ADP5520 |
ed4a10b4 MH |
435 | help |
436 | This option enables support for on-chip LED drivers found | |
437 | on Analog Devices ADP5520/ADP5501 PMICs. | |
438 | ||
439 | To compile this driver as a module, choose M here: the module will | |
440 | be called leds-adp5520. | |
441 | ||
72dcd8d0 BR |
442 | config LEDS_DELL_NETBOOKS |
443 | tristate "External LED on Dell Business Netbooks" | |
0bae35e1 | 444 | depends on LEDS_CLASS |
72dcd8d0 BR |
445 | depends on X86 && ACPI_WMI |
446 | help | |
447 | This adds support for the Latitude 2100 and similar | |
448 | notebooks that have an external LED. | |
449 | ||
7fdcef8a | 450 | config LEDS_MC13783 |
ae6cdb03 | 451 | tristate "LED Support for MC13XXX PMIC" |
0bae35e1 | 452 | depends on LEDS_CLASS |
ae6cdb03 | 453 | depends on MFD_MC13XXX |
7fdcef8a PR |
454 | help |
455 | This option enable support for on-chip LED drivers found | |
a59ce658 | 456 | on Freescale Semiconductor MC13783/MC13892/MC34708 PMIC. |
7fdcef8a | 457 | |
11efe71f SG |
458 | config LEDS_NS2 |
459 | tristate "LED support for Network Space v2 GPIO LEDs" | |
0bae35e1 | 460 | depends on LEDS_CLASS |
259f5ba3 | 461 | depends on MACH_KIRKWOOD || MACH_ARMADA_370 |
11efe71f SG |
462 | default y |
463 | help | |
259f5ba3 SG |
464 | This option enables support for the dual-GPIO LEDs found on the |
465 | following LaCie/Seagate boards: | |
466 | ||
467 | Network Space v2 (and parents: Max, Mini) | |
468 | Internet Space v2 | |
469 | d2 Network v2 | |
470 | n090401 (Seagate NAS 4-Bay) | |
11efe71f | 471 | |
24467832 SG |
472 | config LEDS_NETXBIG |
473 | tristate "LED support for Big Network series LEDs" | |
2504f6da | 474 | depends on LEDS_CLASS |
1093d8ca | 475 | depends on MACH_KIRKWOOD |
24467832 SG |
476 | default y |
477 | help | |
478 | This option enable support for LEDs found on the LaCie 2Big | |
479 | and 5Big Network v2 boards. The LEDs are wired to a CPLD and are | |
480 | controlled through a GPIO extension bus. | |
481 | ||
7d9e7e9f PP |
482 | config LEDS_ASIC3 |
483 | bool "LED support for the HTC ASIC3" | |
9473c4c1 | 484 | depends on LEDS_CLASS=y |
7d9e7e9f PP |
485 | depends on MFD_ASIC3 |
486 | default y | |
487 | help | |
488 | This option enables support for the LEDs on the HTC ASIC3. The HTC | |
489 | ASIC3 LED GPIOs are inputs, not outputs, thus the leds-gpio driver | |
490 | cannot be used. This driver supports hardware blinking with an on+off | |
491 | period from 62ms to 125s. Say Y to enable LEDs on the HP iPAQ hx4700. | |
492 | ||
a6d511e5 N |
493 | config LEDS_TCA6507 |
494 | tristate "LED Support for TCA6507 I2C chip" | |
495 | depends on LEDS_CLASS && I2C | |
496 | help | |
497 | This option enables support for LEDs connected to TC6507 | |
498 | LED driver chips accessed via the I2C bus. | |
499 | Driver support brightness control and hardware-assisted blinking. | |
500 | ||
e370d010 AL |
501 | config LEDS_TLC591XX |
502 | tristate "LED driver for TLC59108 and TLC59116 controllers" | |
503 | depends on LEDS_CLASS && I2C | |
504 | select REGMAP_I2C | |
505 | help | |
506 | This option enables support for Texas Instruments TLC59108 | |
507 | and TLC59116 LED controllers. | |
508 | ||
a43f6a86 JA |
509 | config LEDS_MAX77693 |
510 | tristate "LED support for MAX77693 Flash" | |
511 | depends on LEDS_CLASS_FLASH | |
10c19c9e | 512 | depends on V4L2_FLASH_LED_CLASS || !V4L2_FLASH_LED_CLASS |
a43f6a86 JA |
513 | depends on MFD_MAX77693 |
514 | depends on OF | |
515 | help | |
516 | This option enables support for the flash part of the MAX77693 | |
517 | multifunction device. It has build in control for two leds in flash | |
518 | and torch mode. | |
519 | ||
8584cb82 DK |
520 | config LEDS_MAX8997 |
521 | tristate "LED support for MAX8997 PMIC" | |
522 | depends on LEDS_CLASS && MFD_MAX8997 | |
523 | help | |
524 | This option enables support for on-chip LED drivers on | |
525 | MAXIM MAX8997 PMIC. | |
526 | ||
b98d13c7 SJ |
527 | config LEDS_LM355x |
528 | tristate "LED support for LM355x Chips, LM3554 and LM3556" | |
32abb478 SJ |
529 | depends on LEDS_CLASS && I2C |
530 | select REGMAP_I2C | |
531 | help | |
b98d13c7 SJ |
532 | This option enables support for LEDs connected to LM355x. |
533 | LM355x includes Torch, Flash and Indicator functions. | |
32abb478 | 534 | |
e9a4593c SAS |
535 | config LEDS_OT200 |
536 | tristate "LED support for the Bachmann OT200" | |
d9e8928f | 537 | depends on LEDS_CLASS && HAS_IOMEM && (X86_32 || COMPILE_TEST) |
e9a4593c SAS |
538 | help |
539 | This option enables support for the LEDs on the Bachmann OT200. | |
540 | Say Y to enable LEDs on the Bachmann OT200. | |
541 | ||
38433639 AW |
542 | config LEDS_MENF21BMC |
543 | tristate "LED support for the MEN 14F021P00 BMC" | |
544 | depends on LEDS_CLASS && MFD_MENF21BMC | |
545 | help | |
546 | Say Y here to include support for the MEN 14F021P00 BMC LEDs. | |
547 | ||
548 | This driver can also be built as a module. If so the module | |
549 | will be called leds-menf21bmc. | |
550 | ||
b7da8c5c IK |
551 | config LEDS_KTD2692 |
552 | tristate "LED support for KTD2692 flash LED controller" | |
6e3956cd GU |
553 | depends on LEDS_CLASS_FLASH && OF |
554 | depends on GPIOLIB || COMPILE_TEST | |
b7da8c5c IK |
555 | help |
556 | This option enables support for KTD2692 LED flash connected | |
557 | through ExpressWire interface. | |
558 | ||
559 | Say Y to enable this driver. | |
560 | ||
22a16873 RB |
561 | config LEDS_SEAD3 |
562 | tristate "LED support for the MIPS SEAD 3 board" | |
563 | depends on LEDS_CLASS && MIPS_SEAD3 | |
564 | help | |
565 | Say Y here to include support for the FLED and PLED LEDs on SEAD3 eval | |
566 | boards. | |
567 | ||
568 | This driver can also be built as a module. If so the module | |
569 | will be called leds-sead3. | |
570 | ||
f70ed8a6 VD |
571 | comment "LED driver for blink(1) USB RGB LED is under Special HID drivers (HID_THINGM)" |
572 | ||
b54cf35a JSM |
573 | config LEDS_BLINKM |
574 | tristate "LED support for the BlinkM I2C RGB LED" | |
575 | depends on LEDS_CLASS | |
576 | depends on I2C | |
577 | help | |
578 | This option enables support for the BlinkM RGB LED connected | |
579 | through I2C. Say Y to enable support for the BlinkM LED. | |
580 | ||
84ad6e5c VH |
581 | config LEDS_POWERNV |
582 | tristate "LED support for PowerNV Platform" | |
583 | depends on LEDS_CLASS | |
584 | depends on PPC_POWERNV | |
585 | depends on OF | |
586 | help | |
587 | This option enables support for the system LEDs present on | |
588 | PowerNV platforms. Say 'y' to enable this support in kernel. | |
589 | To compile this driver as a module, choose 'm' here: the module | |
590 | will be called leds-powernv. | |
591 | ||
535f09cc LW |
592 | config LEDS_SYSCON |
593 | bool "LED support for LEDs on system controllers" | |
594 | depends on LEDS_CLASS=y | |
595 | depends on MFD_SYSCON | |
596 | depends on OF | |
597 | help | |
598 | This option enabled support for the LEDs on syscon type | |
599 | devices. This will only work with device tree enabled | |
600 | devices. | |
601 | ||
1dc7d837 | 602 | config LEDS_VERSATILE |
a501fd37 | 603 | tristate "LED support for the ARM Versatile and RealView" |
1dc7d837 LW |
604 | depends on ARCH_REALVIEW || ARCH_VERSATILE |
605 | depends on LEDS_CLASS | |
606 | help | |
607 | This option enabled support for the LEDs on the ARM Versatile | |
608 | and RealView boards. Say Y to enabled these. | |
609 | ||
d09e1666 | 610 | comment "LED Triggers" |
f07fb521 | 611 | source "drivers/leds/trigger/Kconfig" |
44e1e9f8 | 612 | |
66242f7e | 613 | endif # NEW_LEDS |