]>
Commit | Line | Data |
---|---|---|
be5ce2f1 UKK |
1 | config LEDS_GPIO_REGISTER |
2 | bool | |
3 | help | |
4 | This option provides the function gpio_led_register_device. | |
5 | As this function is used by arch code it must not be compiled as a | |
6 | module. | |
7 | ||
66242f7e | 8 | menuconfig NEW_LEDS |
c72a1d60 RP |
9 | bool "LED Support" |
10 | help | |
a8d2e7d9 RP |
11 | Say Y to enable Linux LED support. This allows control of supported |
12 | LEDs from both userspace and optionally, by kernel events (triggers). | |
13 | ||
45d16f09 EM |
14 | if NEW_LEDS |
15 | ||
c72a1d60 | 16 | config LEDS_CLASS |
a403d930 | 17 | tristate "LED Class Support" |
c72a1d60 RP |
18 | help |
19 | This option enables the led sysfs class in /sys/class/leds. You'll | |
20 | need this to do anything useful with LEDs. If unsure, say N. | |
21 | ||
7aea8389 JA |
22 | config LEDS_CLASS_FLASH |
23 | tristate "LED Flash Class Support" | |
24 | depends on LEDS_CLASS | |
25 | help | |
26 | This option enables the flash led sysfs class in /sys/class/leds. | |
27 | It wrapps LED Class and adds flash LEDs specific sysfs attributes | |
28 | and kernel internal API to it. You'll need this to provide support | |
29 | for the flash related features of a LED device. It can be built | |
30 | as a module. | |
31 | ||
24f51e81 | 32 | comment "LED drivers" |
c3bc9956 | 33 | |
0a2f915b HZ |
34 | config LEDS_88PM860X |
35 | tristate "LED Support for Marvell 88PM860x PMIC" | |
0bae35e1 | 36 | depends on LEDS_CLASS |
37814fdc | 37 | depends on MFD_88PM860X |
0a2f915b HZ |
38 | help |
39 | This option enables support for on-chip LED drivers found on Marvell | |
40 | Semiconductor 88PM8606 PMIC. | |
41 | ||
49c34b8e JA |
42 | config LEDS_AAT1290 |
43 | tristate "LED support for the AAT1290" | |
44 | depends on LEDS_CLASS_FLASH | |
58d1809b | 45 | depends on V4L2_FLASH_LED_CLASS || !V4L2_FLASH_LED_CLASS |
6e3956cd | 46 | depends on GPIOLIB || COMPILE_TEST |
49c34b8e | 47 | depends on OF |
ac69b903 | 48 | depends on PINCTRL |
49c34b8e JA |
49 | help |
50 | This option enables support for the LEDs on the AAT1290. | |
51 | ||
fd7b025a ÁFR |
52 | config LEDS_BCM6328 |
53 | tristate "LED Support for Broadcom BCM6328" | |
54 | depends on LEDS_CLASS | |
55 | depends on OF | |
56 | help | |
57 | This option enables support for LEDs connected to the BCM6328 | |
58 | LED HW controller accessed via MMIO registers. | |
59 | ||
589fca16 ÁFR |
60 | config LEDS_BCM6358 |
61 | tristate "LED Support for Broadcom BCM6358" | |
62 | depends on LEDS_CLASS | |
63 | depends on OF | |
64 | help | |
65 | This option enables support for LEDs connected to the BCM6358 | |
66 | LED HW controller accessed via MMIO registers. | |
67 | ||
b1e6b706 SKS |
68 | config LEDS_LM3530 |
69 | tristate "LCD Backlight driver for LM3530" | |
70 | depends on LEDS_CLASS | |
71 | depends on I2C | |
72 | help | |
73 | This option enables support for the LCD backlight using | |
74 | LM3530 ambient light sensor chip. This ALS chip can be | |
75 | controlled manually or using PWM input or using ambient | |
76 | light automatically. | |
77 | ||
401dea7f JH |
78 | config LEDS_LM3533 |
79 | tristate "LED support for LM3533" | |
80 | depends on LEDS_CLASS | |
81 | depends on MFD_LM3533 | |
82 | help | |
83 | This option enables support for the LEDs on National Semiconductor / | |
84 | TI LM3533 Lighting Power chips. | |
85 | ||
86 | The LEDs can be controlled directly, through PWM input, or by the | |
87 | ambient-light-sensor interface. The chip supports | |
88 | hardware-accelerated blinking with maximum on and off periods of 9.8 | |
89 | and 77 seconds respectively. | |
90 | ||
8b7cfbec SJ |
91 | config LEDS_LM3642 |
92 | tristate "LED support for LM3642 Chip" | |
93 | depends on LEDS_CLASS && I2C | |
94 | select REGMAP_I2C | |
95 | help | |
96 | This option enables support for LEDs connected to LM3642. | |
97 | The LM3642 is a 4MHz fixed-frequency synchronous boost | |
98 | converter plus 1.5A constant current driver for a high-current | |
99 | white LED. | |
100 | ||
101 | ||
4d3cb354 RP |
102 | config LEDS_LOCOMO |
103 | tristate "LED Support for Locomo device" | |
0bae35e1 | 104 | depends on LEDS_CLASS |
d09e1666 | 105 | depends on SHARP_LOCOMO |
4d3cb354 RP |
106 | help |
107 | This option enables support for the LEDs on Sharp Locomo. | |
108 | Zaurus models SL-5500 and SL-5600. | |
109 | ||
ac67e23b PS |
110 | config LEDS_MIKROTIK_RB532 |
111 | tristate "LED Support for Mikrotik Routerboard 532" | |
0bae35e1 | 112 | depends on LEDS_CLASS |
d09e1666 | 113 | depends on MIKROTIK_RB532 |
ac67e23b PS |
114 | help |
115 | This option enables support for the so called "User LED" of | |
116 | Mikrotik's Routerboard 532. | |
117 | ||
54bdc470 BD |
118 | config LEDS_S3C24XX |
119 | tristate "LED Support for Samsung S3C24XX GPIO LEDs" | |
0bae35e1 | 120 | depends on LEDS_CLASS |
b130d5c2 | 121 | depends on ARCH_S3C24XX |
54bdc470 BD |
122 | help |
123 | This option enables support for LEDs connected to GPIO lines | |
124 | on Samsung S3C24XX series CPUs, such as the S3C2410 and S3C2440. | |
125 | ||
1a87d942 CB |
126 | config LEDS_NET48XX |
127 | tristate "LED Support for Soekris net48xx series Error LED" | |
0bae35e1 | 128 | depends on LEDS_CLASS |
d09e1666 | 129 | depends on SCx200_GPIO |
1a87d942 CB |
130 | help |
131 | This option enables support for the Soekris net4801 and net4826 error | |
132 | LED. | |
133 | ||
3b2e46f8 RW |
134 | config LEDS_FSG |
135 | tristate "LED Support for the Freecom FSG-3" | |
0bae35e1 | 136 | depends on LEDS_CLASS |
d09e1666 | 137 | depends on MACH_FSG |
3b2e46f8 RW |
138 | help |
139 | This option enables support for the LEDs on the Freecom FSG-3. | |
140 | ||
0d75565f KK |
141 | config LEDS_WRAP |
142 | tristate "LED Support for the WRAP series LEDs" | |
0bae35e1 | 143 | depends on LEDS_CLASS |
d09e1666 | 144 | depends on SCx200_GPIO |
0d75565f KK |
145 | help |
146 | This option enables support for the PCEngines WRAP programmable LEDs. | |
147 | ||
f3b6b6cd YY |
148 | config LEDS_COBALT_QUBE |
149 | tristate "LED Support for the Cobalt Qube series front LED" | |
0bae35e1 | 150 | depends on LEDS_CLASS |
d09e1666 | 151 | depends on MIPS_COBALT |
2fea6f35 | 152 | help |
f3b6b6cd | 153 | This option enables support for the front LED on Cobalt Qube series |
2fea6f35 | 154 | |
97da7aaf YY |
155 | config LEDS_COBALT_RAQ |
156 | bool "LED Support for the Cobalt Raq series" | |
ec149619 | 157 | depends on LEDS_CLASS=y && MIPS_COBALT |
97da7aaf YY |
158 | select LEDS_TRIGGERS |
159 | help | |
160 | This option enables support for the Cobalt Raq series LEDs. | |
161 | ||
5843492c DM |
162 | config LEDS_SUNFIRE |
163 | tristate "LED support for SunFire servers." | |
0bae35e1 | 164 | depends on LEDS_CLASS |
d09e1666 | 165 | depends on SPARC64 |
5843492c DM |
166 | select LEDS_TRIGGERS |
167 | help | |
168 | This option enables support for the Left, Middle, and Right | |
169 | LEDs on the I/O and CPU boards of SunFire UltraSPARC servers. | |
170 | ||
4da498fc LW |
171 | config LEDS_IPAQ_MICRO |
172 | tristate "LED Support for the Compaq iPAQ h3xxx" | |
173 | depends on MFD_IPAQ_MICRO | |
174 | help | |
175 | Choose this option if you want to use the notification LED on | |
176 | Compaq/HP iPAQ h3100 and h3600. | |
177 | ||
d39a7a63 KE |
178 | config LEDS_HP6XX |
179 | tristate "LED Support for the HP Jornada 6xx" | |
0bae35e1 | 180 | depends on LEDS_CLASS |
d09e1666 | 181 | depends on SH_HP6XX |
d39a7a63 | 182 | help |
692105b8 | 183 | This option enables LED support for the handheld |
d39a7a63 KE |
184 | HP Jornada 620/660/680/690. |
185 | ||
e14fa824 RV |
186 | config LEDS_PCA9532 |
187 | tristate "LED driver for PCA9532 dimmer" | |
0bae35e1 | 188 | depends on LEDS_CLASS |
5e0b080d | 189 | depends on I2C && INPUT |
e14fa824 RV |
190 | help |
191 | This option enables support for NXP pca9532 | |
692105b8 | 192 | LED controller. It is generally only useful |
e14fa824 RV |
193 | as a platform driver |
194 | ||
3c1ab50d JE |
195 | config LEDS_PCA9532_GPIO |
196 | bool "Enable GPIO support for PCA9532" | |
197 | depends on LEDS_PCA9532 | |
198 | depends on GPIOLIB | |
199 | help | |
200 | Allow unused pins on PCA9532 to be used as gpio. | |
201 | ||
202 | To use a pin as gpio pca9532_type in pca9532_platform data needs to | |
203 | set to PCA9532_TYPE_GPIO. | |
204 | ||
22e03f3b RA |
205 | config LEDS_GPIO |
206 | tristate "LED Support for GPIO connected LEDs" | |
0bae35e1 | 207 | depends on LEDS_CLASS |
9ab1963d | 208 | depends on GPIOLIB || COMPILE_TEST |
22e03f3b RA |
209 | help |
210 | This option enables support for the LEDs connected to GPIO | |
211 | outputs. To be useful the particular board must have LEDs | |
a7d878af TP |
212 | and they must be connected to the GPIO lines. The LEDs must be |
213 | defined as platform devices and/or OpenFirmware platform devices. | |
214 | The code to use these bindings can be selected below. | |
215 | ||
5054d39e AO |
216 | config LEDS_LP3944 |
217 | tristate "LED Support for N.S. LP3944 (Fun Light) I2C chip" | |
0bae35e1 | 218 | depends on LEDS_CLASS |
d09e1666 | 219 | depends on I2C |
5054d39e | 220 | help |
7f1be819 AO |
221 | This option enables support for LEDs connected to the National |
222 | Semiconductor LP3944 Lighting Management Unit (LMU) also known as | |
223 | Fun Light Chip. | |
5054d39e AO |
224 | |
225 | To compile this driver as a module, choose M here: the | |
226 | module will be called leds-lp3944. | |
227 | ||
c93d08fa | 228 | config LEDS_LP55XX_COMMON |
33b3a561 KM |
229 | tristate "Common Driver for TI/National LP5521/5523/55231/5562/8501" |
230 | depends on LEDS_LP5521 || LEDS_LP5523 || LEDS_LP5562 || LEDS_LP8501 | |
10c06d17 | 231 | select FW_LOADER |
b6789320 | 232 | select FW_LOADER_USER_HELPER_FALLBACK |
c93d08fa | 233 | help |
33b3a561 | 234 | This option supports common operations for LP5521/5523/55231/5562/8501 |
c93d08fa MWK |
235 | devices. |
236 | ||
f4920f67 SO |
237 | config LEDS_LP5521 |
238 | tristate "LED Support for N.S. LP5521 LED driver chip" | |
239 | depends on LEDS_CLASS && I2C | |
c93d08fa | 240 | select LEDS_LP55XX_COMMON |
f4920f67 SO |
241 | help |
242 | If you say yes here you get support for the National Semiconductor | |
243 | LP5521 LED driver. It is 3 channel chip with programmable engines. | |
244 | Driver provides direct control via LED class and interface for | |
245 | programming the engines. | |
246 | ||
247 | config LEDS_LP5523 | |
ca705321 | 248 | tristate "LED Support for TI/National LP5523/55231 LED driver chip" |
f4920f67 | 249 | depends on LEDS_CLASS && I2C |
c93d08fa | 250 | select LEDS_LP55XX_COMMON |
f4920f67 | 251 | help |
ca705321 KM |
252 | If you say yes here you get support for TI/National Semiconductor |
253 | LP5523/55231 LED driver. | |
254 | It is 9 channel chip with programmable engines. | |
f4920f67 SO |
255 | Driver provides direct control via LED class and interface for |
256 | programming the engines. | |
257 | ||
ff45262a KM |
258 | config LEDS_LP5562 |
259 | tristate "LED Support for TI LP5562 LED driver chip" | |
260 | depends on LEDS_CLASS && I2C | |
261 | select LEDS_LP55XX_COMMON | |
262 | help | |
263 | If you say yes here you get support for TI LP5562 LED driver. | |
264 | It is 4 channels chip with programmable engines. | |
265 | Driver provides direct control via LED class and interface for | |
266 | programming the engines. | |
267 | ||
33b3a561 KM |
268 | config LEDS_LP8501 |
269 | tristate "LED Support for TI LP8501 LED driver chip" | |
270 | depends on LEDS_CLASS && I2C | |
271 | select LEDS_LP55XX_COMMON | |
272 | help | |
273 | If you say yes here you get support for TI LP8501 LED driver. | |
274 | It is 9 channel chip with programmable engines. | |
275 | Driver provides direct control via LED class and interface for | |
276 | programming the engines. | |
277 | It is similar as LP5523, but output power selection is available. | |
278 | And register layout and engine program schemes are different. | |
279 | ||
eb80411b KM |
280 | config LEDS_LP8788 |
281 | tristate "LED support for the TI LP8788 PMIC" | |
282 | depends on LEDS_CLASS | |
283 | depends on MFD_LP8788 | |
284 | help | |
285 | This option enables support for the Keyboard LEDs on the LP8788 PMIC. | |
286 | ||
7a8685ac DM |
287 | config LEDS_LP8860 |
288 | tristate "LED support for the TI LP8860 4 channel LED driver" | |
2969bb18 AL |
289 | depends on LEDS_CLASS && I2C |
290 | select REGMAP_I2C | |
7a8685ac DM |
291 | help |
292 | If you say yes here you get support for the TI LP8860 4 channel | |
293 | LED driver. | |
294 | This option enables support for the display cluster LEDs | |
295 | on the LP8860 4 channel LED driver using the I2C communication | |
296 | bus. | |
297 | ||
cec035de | 298 | config LEDS_CLEVO_MAIL |
95dc5768 | 299 | tristate "Mail LED on Clevo notebook" |
0bae35e1 | 300 | depends on LEDS_CLASS |
d09e1666 | 301 | depends on X86 && SERIO_I8042 && DMI |
cec035de MN |
302 | help |
303 | This driver makes the mail LED accessible from userspace | |
304 | programs through the leds subsystem. This LED have three | |
305 | known mode: off, blink at 0.5Hz and blink at 1Hz. | |
306 | ||
92e015cb MN |
307 | The driver supports two kinds of interface: using ledtrig-timer |
308 | or through /sys/class/leds/clevo::mail/brightness. As this LED | |
309 | cannot change it's brightness it blinks instead. The brightness | |
310 | value 0 means off, 1..127 means blink at 0.5Hz and 128..255 means | |
311 | blink at 1Hz. | |
cec035de MN |
312 | |
313 | This module can drive the mail LED for the following notebooks: | |
314 | ||
b3ba31f8 | 315 | Clevo D400P |
cec035de MN |
316 | Clevo D410J |
317 | Clevo D410V | |
318 | Clevo D400V/D470V (not tested, but might work) | |
319 | Clevo M540N | |
320 | Clevo M5x0N (not tested, but might work) | |
321 | Positivo Mobile (Clevo M5x0V) | |
322 | ||
b3ba31f8 | 323 | If your model is not listed here you can try the "nodetect" |
692105b8 | 324 | module parameter. |
b3ba31f8 | 325 | |
cec035de MN |
326 | To compile this driver as a module, choose M here: the |
327 | module will be called leds-clevo-mail. | |
328 | ||
f46e9203 NC |
329 | config LEDS_PCA955X |
330 | tristate "LED Support for PCA955x I2C chips" | |
0bae35e1 | 331 | depends on LEDS_CLASS |
d09e1666 | 332 | depends on I2C |
f46e9203 NC |
333 | help |
334 | This option enables support for LEDs connected to PCA955x | |
335 | LED driver chips accessed via the I2C bus. Supported | |
336 | devices include PCA9550, PCA9551, PCA9552, and PCA9553. | |
337 | ||
56a1740c | 338 | config LEDS_PCA963X |
af67384f | 339 | tristate "LED support for PCA963x I2C chip" |
75cb2e1d PM |
340 | depends on LEDS_CLASS |
341 | depends on I2C | |
342 | help | |
af67384f RRD |
343 | This option enables support for LEDs connected to the PCA963x |
344 | LED driver chip accessed via the I2C bus. Supported | |
345 | devices include PCA9633 and PCA9634 | |
75cb2e1d | 346 | |
c746b551 MB |
347 | config LEDS_WM831X_STATUS |
348 | tristate "LED support for status LEDs on WM831x PMICs" | |
0bae35e1 | 349 | depends on LEDS_CLASS |
d09e1666 | 350 | depends on MFD_WM831X |
c746b551 MB |
351 | help |
352 | This option enables support for the status LEDs of the WM831x | |
353 | series of PMICs. | |
354 | ||
0081e802 MB |
355 | config LEDS_WM8350 |
356 | tristate "LED Support for WM8350 AudioPlus PMIC" | |
0bae35e1 | 357 | depends on LEDS_CLASS |
d09e1666 | 358 | depends on MFD_WM8350 |
0081e802 MB |
359 | help |
360 | This option enables support for LEDs driven by the Wolfson | |
361 | Microelectronics WM8350 AudioPlus PMIC. | |
362 | ||
9e84561c MR |
363 | config LEDS_DA903X |
364 | tristate "LED Support for DA9030/DA9034 PMIC" | |
0bae35e1 | 365 | depends on LEDS_CLASS |
d09e1666 | 366 | depends on PMIC_DA903X |
9e84561c MR |
367 | help |
368 | This option enables support for on-chip LED drivers found | |
369 | on Dialog Semiconductor DA9030/DA9034 PMICs. | |
370 | ||
5ba73631 DDC |
371 | config LEDS_DA9052 |
372 | tristate "Dialog DA9052/DA9053 LEDS" | |
373 | depends on LEDS_CLASS | |
374 | depends on PMIC_DA9052 | |
375 | help | |
376 | This option enables support for on-chip LED drivers found | |
377 | on Dialog Semiconductor DA9052-BC and DA9053-AA/Bx PMICs. | |
378 | ||
ac2dd0f1 GL |
379 | config LEDS_DAC124S085 |
380 | tristate "LED Support for DAC124S085 SPI DAC" | |
0bae35e1 | 381 | depends on LEDS_CLASS |
d09e1666 | 382 | depends on SPI |
ac2dd0f1 GL |
383 | help |
384 | This option enables support for DAC124S085 SPI DAC from NatSemi, | |
385 | which can be used to control up to four LEDs. | |
386 | ||
41c42ff5 LF |
387 | config LEDS_PWM |
388 | tristate "PWM driven LED Support" | |
0bae35e1 | 389 | depends on LEDS_CLASS |
ad0ba85f | 390 | depends on PWM |
41c42ff5 LF |
391 | help |
392 | This option enables support for pwm driven LEDs | |
393 | ||
d4cc6a2e AO |
394 | config LEDS_REGULATOR |
395 | tristate "REGULATOR driven LED support" | |
0bae35e1 | 396 | depends on LEDS_CLASS |
d09e1666 | 397 | depends on REGULATOR |
d4cc6a2e AO |
398 | help |
399 | This option enables support for regulator driven LEDs. | |
400 | ||
0b56129b KK |
401 | config LEDS_BD2802 |
402 | tristate "LED driver for BD2802 RGB LED" | |
0bae35e1 | 403 | depends on LEDS_CLASS |
d09e1666 | 404 | depends on I2C |
0b56129b KK |
405 | help |
406 | This option enables support for BD2802GU RGB LED driver chips | |
407 | accessed via the I2C bus. | |
408 | ||
a328e95b DH |
409 | config LEDS_INTEL_SS4200 |
410 | tristate "LED driver for Intel NAS SS4200 series" | |
0bae35e1 | 411 | depends on LEDS_CLASS |
d09e1666 | 412 | depends on PCI && DMI |
a328e95b DH |
413 | help |
414 | This option enables support for the Intel SS4200 series of | |
415 | Network Attached Storage servers. You may control the hard | |
416 | drive or power LEDs on the front panel. Using this driver | |
417 | can stop the front LED from blinking after startup. | |
418 | ||
a8dd18fe DM |
419 | config LEDS_LT3593 |
420 | tristate "LED driver for LT3593 controllers" | |
0bae35e1 | 421 | depends on LEDS_CLASS |
82322741 | 422 | depends on GPIOLIB || COMPILE_TEST |
a8dd18fe DM |
423 | help |
424 | This option enables support for LEDs driven by a Linear Technology | |
425 | LT3593 controller. This controller uses a special one-wire pulse | |
426 | coding protocol to set the brightness. | |
427 | ||
ed4a10b4 MH |
428 | config LEDS_ADP5520 |
429 | tristate "LED Support for ADP5520/ADP5501 PMIC" | |
0bae35e1 | 430 | depends on LEDS_CLASS |
d09e1666 | 431 | depends on PMIC_ADP5520 |
ed4a10b4 MH |
432 | help |
433 | This option enables support for on-chip LED drivers found | |
434 | on Analog Devices ADP5520/ADP5501 PMICs. | |
435 | ||
436 | To compile this driver as a module, choose M here: the module will | |
437 | be called leds-adp5520. | |
438 | ||
72dcd8d0 BR |
439 | config LEDS_DELL_NETBOOKS |
440 | tristate "External LED on Dell Business Netbooks" | |
0bae35e1 | 441 | depends on LEDS_CLASS |
72dcd8d0 BR |
442 | depends on X86 && ACPI_WMI |
443 | help | |
444 | This adds support for the Latitude 2100 and similar | |
445 | notebooks that have an external LED. | |
446 | ||
7fdcef8a | 447 | config LEDS_MC13783 |
ae6cdb03 | 448 | tristate "LED Support for MC13XXX PMIC" |
0bae35e1 | 449 | depends on LEDS_CLASS |
ae6cdb03 | 450 | depends on MFD_MC13XXX |
7fdcef8a PR |
451 | help |
452 | This option enable support for on-chip LED drivers found | |
a59ce658 | 453 | on Freescale Semiconductor MC13783/MC13892/MC34708 PMIC. |
7fdcef8a | 454 | |
11efe71f SG |
455 | config LEDS_NS2 |
456 | tristate "LED support for Network Space v2 GPIO LEDs" | |
0bae35e1 | 457 | depends on LEDS_CLASS |
259f5ba3 | 458 | depends on MACH_KIRKWOOD || MACH_ARMADA_370 |
11efe71f SG |
459 | default y |
460 | help | |
259f5ba3 SG |
461 | This option enables support for the dual-GPIO LEDs found on the |
462 | following LaCie/Seagate boards: | |
463 | ||
464 | Network Space v2 (and parents: Max, Mini) | |
465 | Internet Space v2 | |
466 | d2 Network v2 | |
467 | n090401 (Seagate NAS 4-Bay) | |
11efe71f | 468 | |
24467832 SG |
469 | config LEDS_NETXBIG |
470 | tristate "LED support for Big Network series LEDs" | |
2504f6da | 471 | depends on LEDS_CLASS |
1093d8ca | 472 | depends on MACH_KIRKWOOD |
24467832 SG |
473 | default y |
474 | help | |
475 | This option enable support for LEDs found on the LaCie 2Big | |
476 | and 5Big Network v2 boards. The LEDs are wired to a CPLD and are | |
477 | controlled through a GPIO extension bus. | |
478 | ||
7d9e7e9f PP |
479 | config LEDS_ASIC3 |
480 | bool "LED support for the HTC ASIC3" | |
9473c4c1 | 481 | depends on LEDS_CLASS=y |
7d9e7e9f PP |
482 | depends on MFD_ASIC3 |
483 | default y | |
484 | help | |
485 | This option enables support for the LEDs on the HTC ASIC3. The HTC | |
486 | ASIC3 LED GPIOs are inputs, not outputs, thus the leds-gpio driver | |
487 | cannot be used. This driver supports hardware blinking with an on+off | |
488 | period from 62ms to 125s. Say Y to enable LEDs on the HP iPAQ hx4700. | |
489 | ||
a6d511e5 N |
490 | config LEDS_TCA6507 |
491 | tristate "LED Support for TCA6507 I2C chip" | |
492 | depends on LEDS_CLASS && I2C | |
493 | help | |
494 | This option enables support for LEDs connected to TC6507 | |
495 | LED driver chips accessed via the I2C bus. | |
496 | Driver support brightness control and hardware-assisted blinking. | |
497 | ||
e370d010 AL |
498 | config LEDS_TLC591XX |
499 | tristate "LED driver for TLC59108 and TLC59116 controllers" | |
500 | depends on LEDS_CLASS && I2C | |
501 | select REGMAP_I2C | |
502 | help | |
503 | This option enables support for Texas Instruments TLC59108 | |
504 | and TLC59116 LED controllers. | |
505 | ||
a43f6a86 JA |
506 | config LEDS_MAX77693 |
507 | tristate "LED support for MAX77693 Flash" | |
508 | depends on LEDS_CLASS_FLASH | |
10c19c9e | 509 | depends on V4L2_FLASH_LED_CLASS || !V4L2_FLASH_LED_CLASS |
a43f6a86 JA |
510 | depends on MFD_MAX77693 |
511 | depends on OF | |
512 | help | |
513 | This option enables support for the flash part of the MAX77693 | |
514 | multifunction device. It has build in control for two leds in flash | |
515 | and torch mode. | |
516 | ||
8584cb82 DK |
517 | config LEDS_MAX8997 |
518 | tristate "LED support for MAX8997 PMIC" | |
519 | depends on LEDS_CLASS && MFD_MAX8997 | |
520 | help | |
521 | This option enables support for on-chip LED drivers on | |
522 | MAXIM MAX8997 PMIC. | |
523 | ||
b98d13c7 SJ |
524 | config LEDS_LM355x |
525 | tristate "LED support for LM355x Chips, LM3554 and LM3556" | |
32abb478 SJ |
526 | depends on LEDS_CLASS && I2C |
527 | select REGMAP_I2C | |
528 | help | |
b98d13c7 SJ |
529 | This option enables support for LEDs connected to LM355x. |
530 | LM355x includes Torch, Flash and Indicator functions. | |
32abb478 | 531 | |
e9a4593c SAS |
532 | config LEDS_OT200 |
533 | tristate "LED support for the Bachmann OT200" | |
d9e8928f | 534 | depends on LEDS_CLASS && HAS_IOMEM && (X86_32 || COMPILE_TEST) |
e9a4593c SAS |
535 | help |
536 | This option enables support for the LEDs on the Bachmann OT200. | |
537 | Say Y to enable LEDs on the Bachmann OT200. | |
538 | ||
38433639 AW |
539 | config LEDS_MENF21BMC |
540 | tristate "LED support for the MEN 14F021P00 BMC" | |
541 | depends on LEDS_CLASS && MFD_MENF21BMC | |
542 | help | |
543 | Say Y here to include support for the MEN 14F021P00 BMC LEDs. | |
544 | ||
545 | This driver can also be built as a module. If so the module | |
546 | will be called leds-menf21bmc. | |
547 | ||
b7da8c5c IK |
548 | config LEDS_KTD2692 |
549 | tristate "LED support for KTD2692 flash LED controller" | |
6e3956cd GU |
550 | depends on LEDS_CLASS_FLASH && OF |
551 | depends on GPIOLIB || COMPILE_TEST | |
b7da8c5c IK |
552 | help |
553 | This option enables support for KTD2692 LED flash connected | |
554 | through ExpressWire interface. | |
555 | ||
556 | Say Y to enable this driver. | |
557 | ||
f70ed8a6 VD |
558 | comment "LED driver for blink(1) USB RGB LED is under Special HID drivers (HID_THINGM)" |
559 | ||
b54cf35a JSM |
560 | config LEDS_BLINKM |
561 | tristate "LED support for the BlinkM I2C RGB LED" | |
562 | depends on LEDS_CLASS | |
563 | depends on I2C | |
564 | help | |
565 | This option enables support for the BlinkM RGB LED connected | |
566 | through I2C. Say Y to enable support for the BlinkM LED. | |
567 | ||
84ad6e5c VH |
568 | config LEDS_POWERNV |
569 | tristate "LED support for PowerNV Platform" | |
570 | depends on LEDS_CLASS | |
571 | depends on PPC_POWERNV | |
572 | depends on OF | |
573 | help | |
574 | This option enables support for the system LEDs present on | |
575 | PowerNV platforms. Say 'y' to enable this support in kernel. | |
576 | To compile this driver as a module, choose 'm' here: the module | |
577 | will be called leds-powernv. | |
578 | ||
535f09cc LW |
579 | config LEDS_SYSCON |
580 | bool "LED support for LEDs on system controllers" | |
581 | depends on LEDS_CLASS=y | |
582 | depends on MFD_SYSCON | |
583 | depends on OF | |
584 | help | |
585 | This option enabled support for the LEDs on syscon type | |
586 | devices. This will only work with device tree enabled | |
587 | devices. | |
588 | ||
1dc7d837 | 589 | config LEDS_VERSATILE |
a501fd37 | 590 | tristate "LED support for the ARM Versatile and RealView" |
1dc7d837 LW |
591 | depends on ARCH_REALVIEW || ARCH_VERSATILE |
592 | depends on LEDS_CLASS | |
593 | help | |
594 | This option enabled support for the LEDs on the ARM Versatile | |
595 | and RealView boards. Say Y to enabled these. | |
596 | ||
d09e1666 | 597 | comment "LED Triggers" |
f07fb521 | 598 | source "drivers/leds/trigger/Kconfig" |
44e1e9f8 | 599 | |
66242f7e | 600 | endif # NEW_LEDS |