[mirror_ubuntu-jammy-kernel.git] / drivers / net / Kconfig

#
# Network device configuration
#

menuconfig NETDEVICES
	default y if UML
	depends on NET
	bool "Network device support"
	---help---
	  You can say N here if you don't intend to connect your Linux box to
	  any other computer at all.

	  You'll have to say Y if your computer contains a network card that
	  you want to use under Linux. If you are going to run SLIP or PPP over
	  telephone line or null modem cable you need say Y here. Connecting
	  two machines with parallel ports using PLIP needs this, as well as
	  AX.25/KISS for sending Internet traffic over amateur radio links.

	  See also "The Linux Network Administrator's Guide" by Olaf Kirch and
	  Terry Dawson. Available at <http://www.tldp.org/guides.html>.

	  If unsure, say Y.

# All the following symbols are dependent on NETDEVICES - do not repeat
# that for each of the symbols.
if NETDEVICES

config NET_CORE
	default y
	bool "Network core driver support"
	---help---
	  You can say N here if you do not intend to use any of the
	  networking core drivers (i.e. VLAN, bridging, bonding, etc.)

if NET_CORE

config BONDING
	tristate "Bonding driver support"
	depends on INET
	depends on IPV6 || IPV6=n
	---help---
	  Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet
	  Channels together. This is called 'Etherchannel' by Cisco,
	  'Trunking' by Sun, 802.3ad by the IEEE, and 'Bonding' in Linux.

	  The driver supports multiple bonding modes to allow for both high
	  performance and high availability operation.

	  Refer to <file:Documentation/networking/bonding.txt> for more
	  information.

	  To compile this driver as a module, choose M here: the module
	  will be called bonding.

config DUMMY
	tristate "Dummy net driver support"
	---help---
	  This is essentially a bit-bucket device (i.e. traffic you send to
	  this device is consigned into oblivion) with a configurable IP
	  address. It is most commonly used in order to make your currently
	  inactive SLIP address seem like a real address for local programs.
	  If you use SLIP or PPP, you might want to say Y here. Since this
	  thing often comes in handy, the default is Y. It won't enlarge your
	  kernel either. What a deal. Read about it in the Network
	  Administrator's Guide, available from
	  <http://www.tldp.org/docs.html#guide>.

	  To compile this driver as a module, choose M here: the module
	  will be called dummy.

config EQUALIZER
	tristate "EQL (serial line load balancing) support"
	---help---
	  If you have two serial connections to some other computer (this
	  usually requires two modems and two telephone lines) and you use
	  SLIP (the protocol for sending Internet traffic over telephone
	  lines) or PPP (a better SLIP) on them, you can make them behave like
	  one double speed connection using this driver.  Naturally, this has
	  to be supported at the other end as well, either with a similar EQL
	  Linux driver or with a Livingston Portmaster 2e.

	  Say Y if you want this and read
	  <file:Documentation/networking/eql.txt>.  You may also want to read
	  section 6.2 of the NET-3-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here: the module
	  will be called eql.  If unsure, say N.

config NET_FC
	bool "Fibre Channel driver support"
	depends on SCSI && PCI
	help
	  Fibre Channel is a high speed serial protocol mainly used to connect
	  large storage devices to the computer; it is compatible with and
	  intended to replace SCSI.

	  If you intend to use Fibre Channel, you need to have a Fibre channel
	  adaptor card in your computer; say Y here and to the driver for your
	  adaptor below. You also should have said Y to "SCSI support" and
	  "SCSI generic support".

config MII
	tristate "Generic Media Independent Interface device support"
	help
	  Most ethernet controllers have MII transceiver either as an external
	  or internal device.  It is safe to say Y or M here even if your
	  ethernet card lacks MII.

config IFB
	tristate "Intermediate Functional Block support"
	depends on NET_CLS_ACT
	---help---
	  This is an intermediate driver that allows sharing of
	  resources.
	  To compile this driver as a module, choose M here: the module
	  will be called ifb.  If you want to use more than one ifb
	  device at a time, you need to compile this driver as a module.
	  Instead of 'ifb', the devices will then be called 'ifb0',
	  'ifb1' etc.
	  Look at the iproute2 documentation directory for usage etc

source "drivers/net/team/Kconfig"

config MACVLAN
	tristate "MAC-VLAN support (EXPERIMENTAL)"
	depends on EXPERIMENTAL
	---help---
	  This allows one to create virtual interfaces that map packets to
	  or from specific MAC addresses to a particular interface.

	  Macvlan devices can be added using the "ip" command from the
	  iproute2 package starting with the iproute2-2.6.23 release:

	  "ip link add link <real dev> [ address MAC ] [ NAME ] type macvlan"

	  To compile this driver as a module, choose M here: the module
	  will be called macvlan.

config MACVTAP
	tristate "MAC-VLAN based tap driver (EXPERIMENTAL)"
	depends on MACVLAN
	help
	  This adds a specialized tap character device driver that is based
	  on the MAC-VLAN network interface, called macvtap. A macvtap device
	  can be added in the same way as a macvlan device, using 'type
	  macvlan', and then be accessed through the tap user space interface.

	  To compile this driver as a module, choose M here: the module
	  will be called macvtap.

config NETCONSOLE
	tristate "Network console logging support"
	---help---
	If you want to log kernel messages over the network, enable this.
	See <file:Documentation/networking/netconsole.txt> for details.

config NETCONSOLE_DYNAMIC
	bool "Dynamic reconfiguration of logging targets"
	depends on NETCONSOLE && SYSFS && CONFIGFS_FS && \
			!(NETCONSOLE=y && CONFIGFS_FS=m)
	help
	  This option enables the ability to dynamically reconfigure target
	  parameters (interface, IP addresses, port numbers, MAC addresses)
	  at runtime through a userspace interface exported using configfs.
	  See <file:Documentation/networking/netconsole.txt> for details.

config NETPOLL
	def_bool NETCONSOLE

config NETPOLL_TRAP
	bool "Netpoll traffic trapping"
	default n
	depends on NETPOLL

config NET_POLL_CONTROLLER
	def_bool NETPOLL

config RIONET
	tristate "RapidIO Ethernet over messaging driver support"
	depends on RAPIDIO

config RIONET_TX_SIZE
	int "Number of outbound queue entries"
	depends on RIONET
	default "128"

config RIONET_RX_SIZE
	int "Number of inbound queue entries"
	depends on RIONET
	default "128"

config TUN
	tristate "Universal TUN/TAP device driver support"
	select CRC32
	---help---
	  TUN/TAP provides packet reception and transmission for user space
	  programs.  It can be viewed as a simple Point-to-Point or Ethernet
	  device, which instead of receiving packets from a physical media,
	  receives them from user space program and instead of sending packets
	  via physical media writes them to the user space program.

	  When a program opens /dev/net/tun, driver creates and registers
	  corresponding net device tunX or tapX.  After a program closed above
	  devices, driver will automatically delete tunXX or tapXX device and
	  all routes corresponding to it.

	  Please read <file:Documentation/networking/tuntap.txt> for more
	  information.

	  To compile this driver as a module, choose M here: the module
	  will be called tun.

	  If you don't know what to use this for, you don't need it.

config VETH
	tristate "Virtual ethernet pair device"
	---help---
	  This device is a local ethernet tunnel. Devices are created in pairs.
	  When one end receives the packet it appears on its pair and vice
	  versa.

config VIRTIO_NET
	tristate "Virtio network driver (EXPERIMENTAL)"
	depends on EXPERIMENTAL && VIRTIO
	---help---
	  This is the virtual network driver for virtio.  It can be used with
	  lguest or QEMU based VMMs (like KVM or Xen).  Say Y or M.

endif # NET_CORE

config SUNGEM_PHY
	tristate

source "drivers/net/arcnet/Kconfig"

source "drivers/atm/Kconfig"

source "drivers/net/caif/Kconfig"

source "drivers/net/dsa/Kconfig"

source "drivers/net/ethernet/Kconfig"

source "drivers/net/fddi/Kconfig"

source "drivers/net/hippi/Kconfig"

config NET_SB1000
	tristate "General Instruments Surfboard 1000"
	depends on PNP
	---help---
	  This is a driver for the General Instrument (also known as
	  NextLevel) SURFboard 1000 internal
	  cable modem. This is an ISA card which is used by a number of cable
	  TV companies to provide cable modem access. It's a one-way
	  downstream-only cable modem, meaning that your upstream net link is
	  provided by your regular phone modem.

	  At present this driver only compiles as a module, so say M here if
	  you have this card. The module will be called sb1000. Then read
	  <file:Documentation/networking/README.sb1000> for information on how
	  to use this module, as it needs special ppp scripts for establishing
	  a connection. Further documentation and the necessary scripts can be
	  found at:

	  <http://www.jacksonville.net/~fventuri/>
	  <http://home.adelphia.net/~siglercm/sb1000.html>
	  <http://linuxpower.cx/~cable/>

	  If you don't have this card, of course say N.

source "drivers/net/phy/Kconfig"

source "drivers/net/plip/Kconfig"

source "drivers/net/ppp/Kconfig"

source "drivers/net/slip/Kconfig"

source "drivers/s390/net/Kconfig"

source "drivers/net/usb/Kconfig"

source "drivers/net/wireless/Kconfig"

source "drivers/net/wimax/Kconfig"

source "drivers/net/wan/Kconfig"

source "drivers/net/ieee802154/Kconfig"

config XEN_NETDEV_FRONTEND
	tristate "Xen network device frontend driver"
	depends on XEN
	select XEN_XENBUS_FRONTEND
	default y
	help
	  This driver provides support for Xen paravirtual network
	  devices exported by a Xen network driver domain (often
	  domain 0).

	  The corresponding Linux backend driver is enabled by the
	  CONFIG_XEN_NETDEV_BACKEND option.

	  If you are compiling a kernel for use as Xen guest, you
	  should say Y here. To compile this driver as a module, chose
	  M here: the module will be called xen-netfront.

config XEN_NETDEV_BACKEND
	tristate "Xen backend network device"
	depends on XEN_BACKEND
	help
	  This driver allows the kernel to act as a Xen network driver
	  domain which exports paravirtual network devices to other
	  Xen domains. These devices can be accessed by any operating
	  system that implements a compatible front end.

	  The corresponding Linux frontend driver is enabled by the
	  CONFIG_XEN_NETDEV_FRONTEND configuration option.

	  The backend driver presents a standard network device
	  endpoint for each paravirtual network device to the driver
	  domain network stack. These can then be bridged or routed
	  etc in order to provide full network connectivity.

	  If you are compiling a kernel to run in a Xen network driver
	  domain (often this is domain 0) you should say Y here. To
	  compile this driver as a module, chose M here: the module
	  will be called xen-netback.

config VMXNET3
	tristate "VMware VMXNET3 ethernet driver"
	depends on PCI && INET
	help
	  This driver supports VMware's vmxnet3 virtual ethernet NIC.
	  To compile this driver as a module, choose M here: the
	  module will be called vmxnet3.

source "drivers/net/hyperv/Kconfig"

endif # NETDEVICES
Commit	Line	Data
1da177e4 LT	1	#
	2	# Network device configuration
	3	#
	4
d1c0a65f	5	menuconfig NETDEVICES
ce2d2aed	6	default y if UML
e0009820	7	depends on NET
1da177e4 LT	8	bool "Network device support"
	9	---help---
	10	You can say N here if you don't intend to connect your Linux box to
	11	any other computer at all.
	12
	13	You'll have to say Y if your computer contains a network card that
	14	you want to use under Linux. If you are going to run SLIP or PPP over
	15	telephone line or null modem cable you need say Y here. Connecting
	16	two machines with parallel ports using PLIP needs this, as well as
	17	AX.25/KISS for sending Internet traffic over amateur radio links.
	18
	19	See also "The Linux Network Administrator's Guide" by Olaf Kirch and
	20	Terry Dawson. Available at <http://www.tldp.org/guides.html>.
	21
	22	If unsure, say Y.
	23
1618cb0c RD	24	# All the following symbols are dependent on NETDEVICES - do not repeat
	25	# that for each of the symbols.
	26	if NETDEVICES
cbcd2a4c	27
88491d81 JK	28	config NET_CORE
	29	default y
	30	bool "Network core driver support"
253af423	31	---help---
88491d81 JK	32	You can say N here if you do not intend to use any of the
	33	networking core drivers (i.e. VLAN, bridging, bonding, etc.)
	34
	35	if NET_CORE
	36
	37	config BONDING
	38	tristate "Bonding driver support"
	39	depends on INET
	40	depends on IPV6 \|\| IPV6=n
	41	---help---
	42	Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet
	43	Channels together. This is called 'Etherchannel' by Cisco,
	44	'Trunking' by Sun, 802.3ad by the IEEE, and 'Bonding' in Linux.
	45
	46	The driver supports multiple bonding modes to allow for both high
	47	performance and high availability operation.
	48
	49	Refer to <file:Documentation/networking/bonding.txt> for more
	50	information.
	51
253af423	52	To compile this driver as a module, choose M here: the module
88491d81	53	will be called bonding.
253af423	54
1da177e4 LT	55	config DUMMY
1da177e4 LT	56	tristate "Dummy net driver support"
1da177e4 LT	57	---help---
	58	This is essentially a bit-bucket device (i.e. traffic you send to
	59	this device is consigned into oblivion) with a configurable IP
	60	address. It is most commonly used in order to make your currently
	61	inactive SLIP address seem like a real address for local programs.
	62	If you use SLIP or PPP, you might want to say Y here. Since this
	63	thing often comes in handy, the default is Y. It won't enlarge your
	64	kernel either. What a deal. Read about it in the Network
	65	Administrator's Guide, available from
	66	<http://www.tldp.org/docs.html#guide>.
	67
	68	To compile this driver as a module, choose M here: the module
9f486619	69	will be called dummy.
1da177e4	70
88491d81 JK	71	config EQUALIZER
88491d81 JK	72	tristate "EQL (serial line load balancing) support"
1da177e4	73	---help---
88491d81 JK	74	If you have two serial connections to some other computer (this
	75	usually requires two modems and two telephone lines) and you use
	76	SLIP (the protocol for sending Internet traffic over telephone
	77	lines) or PPP (a better SLIP) on them, you can make them behave like
	78	one double speed connection using this driver. Naturally, this has
	79	to be supported at the other end as well, either with a similar EQL
	80	Linux driver or with a Livingston Portmaster 2e.
1da177e4	81
88491d81 JK	82	Say Y if you want this and read
	83	<file:Documentation/networking/eql.txt>. You may also want to read
	84	section 6.2 of the NET-3-HOWTO, available from
	85	<http://www.tldp.org/docs.html#howto>.
1da177e4	86
88491d81 JK	87	To compile this driver as a module, choose M here: the module
	88	will be called eql. If unsure, say N.
	89
	90	config NET_FC
	91	bool "Fibre Channel driver support"
	92	depends on SCSI && PCI
	93	help
	94	Fibre Channel is a high speed serial protocol mainly used to connect
	95	large storage devices to the computer; it is compatible with and
	96	intended to replace SCSI.
	97
	98	If you intend to use Fibre Channel, you need to have a Fibre channel
	99	adaptor card in your computer; say Y here and to the driver for your
	100	adaptor below. You also should have said Y to "SCSI support" and
	101	"SCSI generic support".
1da177e4	102
88491d81 JK	103	config MII
	104	tristate "Generic Media Independent Interface device support"
	105	help
	106	Most ethernet controllers have MII transceiver either as an external
	107	or internal device. It is safe to say Y or M here even if your
	108	ethernet card lacks MII.
	109
88491d81 JK	110	config IFB
	111	tristate "Intermediate Functional Block support"
	112	depends on NET_CLS_ACT
	113	---help---
	114	This is an intermediate driver that allows sharing of
	115	resources.
1da177e4	116	To compile this driver as a module, choose M here: the module
88491d81 JK	117	will be called ifb. If you want to use more than one ifb
	118	device at a time, you need to compile this driver as a module.
	119	Instead of 'ifb', the devices will then be called 'ifb0',
	120	'ifb1' etc.
	121	Look at the iproute2 documentation directory for usage etc
1da177e4	122
3d249d4c JP	123	source "drivers/net/team/Kconfig"
3d249d4c JP	124
b863ceb7 PM	125	config MACVLAN
	126	tristate "MAC-VLAN support (EXPERIMENTAL)"
	127	depends on EXPERIMENTAL
	128	---help---
	129	This allows one to create virtual interfaces that map packets to
	130	or from specific MAC addresses to a particular interface.
	131
3dbf8d56 PM	132	Macvlan devices can be added using the "ip" command from the
	133	iproute2 package starting with the iproute2-2.6.23 release:
	134
	135	"ip link add link <real dev> [ address MAC ] [ NAME ] type macvlan"
	136
b863ceb7 PM	137	To compile this driver as a module, choose M here: the module
	138	will be called macvlan.
	139
20d29d7a AB	140	config MACVTAP
	141	tristate "MAC-VLAN based tap driver (EXPERIMENTAL)"
	142	depends on MACVLAN
	143	help
	144	This adds a specialized tap character device driver that is based
	145	on the MAC-VLAN network interface, called macvtap. A macvtap device
	146	can be added in the same way as a macvlan device, using 'type
	147	macvlan', and then be accessed through the tap user space interface.
	148
	149	To compile this driver as a module, choose M here: the module
	150	will be called macvtap.
	151
88491d81 JK	152	config NETCONSOLE
88491d81 JK	153	tristate "Network console logging support"
1da177e4	154	---help---
88491d81 JK	155	If you want to log kernel messages over the network, enable this.
88491d81 JK	156	See <file:Documentation/networking/netconsole.txt> for details.
1da177e4	157
88491d81 JK	158	config NETCONSOLE_DYNAMIC
	159	bool "Dynamic reconfiguration of logging targets"
	160	depends on NETCONSOLE && SYSFS && CONFIGFS_FS && \
	161	!(NETCONSOLE=y && CONFIGFS_FS=m)
	162	help
	163	This option enables the ability to dynamically reconfigure target
	164	parameters (interface, IP addresses, port numbers, MAC addresses)
	165	at runtime through a userspace interface exported using configfs.
	166	See <file:Documentation/networking/netconsole.txt> for details.
1da177e4	167
88491d81 JK	168	config NETPOLL
	169	def_bool NETCONSOLE
	170
	171	config NETPOLL_TRAP
	172	bool "Netpoll traffic trapping"
	173	default n
	174	depends on NETPOLL
	175
	176	config NET_POLL_CONTROLLER
	177	def_bool NETPOLL
	178
	179	config RIONET
	180	tristate "RapidIO Ethernet over messaging driver support"
	181	depends on RAPIDIO
	182
	183	config RIONET_TX_SIZE
	184	int "Number of outbound queue entries"
	185	depends on RIONET
	186	default "128"
	187
	188	config RIONET_RX_SIZE
	189	int "Number of inbound queue entries"
	190	depends on RIONET
	191	default "128"
1da177e4 LT	192
	193	config TUN
	194	tristate "Universal TUN/TAP device driver support"
1da177e4 LT	195	select CRC32
	196	---help---
	197	TUN/TAP provides packet reception and transmission for user space
	198	programs. It can be viewed as a simple Point-to-Point or Ethernet
	199	device, which instead of receiving packets from a physical media,
	200	receives them from user space program and instead of sending packets
	201	via physical media writes them to the user space program.
	202
	203	When a program opens /dev/net/tun, driver creates and registers
	204	corresponding net device tunX or tapX. After a program closed above
	205	devices, driver will automatically delete tunXX or tapXX device and
	206	all routes corresponding to it.
	207
	208	Please read <file:Documentation/networking/tuntap.txt> for more
	209	information.
	210
	211	To compile this driver as a module, choose M here: the module
	212	will be called tun.
	213
	214	If you don't know what to use this for, you don't need it.
	215
e314dbdc	216	config VETH
6a9a0250	217	tristate "Virtual ethernet pair device"
e314dbdc	218	---help---
6a9a0250 RR	219	This device is a local ethernet tunnel. Devices are created in pairs.
	220	When one end receives the packet it appears on its pair and vice
	221	versa.
e314dbdc	222
88491d81 JK	223	config VIRTIO_NET
	224	tristate "Virtio network driver (EXPERIMENTAL)"
	225	depends on EXPERIMENTAL && VIRTIO
	226	---help---
	227	This is the virtual network driver for virtio. It can be used with
	228	lguest or QEMU based VMMs (like KVM or Xen). Say Y or M.
	229
	230	endif # NET_CORE
	231
	232	config SUNGEM_PHY
	233	tristate
	234
	235	source "drivers/net/arcnet/Kconfig"
	236
	237	source "drivers/atm/Kconfig"
	238
	239	source "drivers/net/caif/Kconfig"
	240
3b158859 BH	241	source "drivers/net/dsa/Kconfig"
3b158859 BH	242
88491d81 JK	243	source "drivers/net/ethernet/Kconfig"
	244
	245	source "drivers/net/fddi/Kconfig"
	246
fecc7351 PB	247	source "drivers/net/hippi/Kconfig"
fecc7351 PB	248
1da177e4 LT	249	config NET_SB1000
1da177e4 LT	250	tristate "General Instruments Surfboard 1000"
cbcd2a4c	251	depends on PNP
1da177e4 LT	252	---help---
	253	This is a driver for the General Instrument (also known as
	254	NextLevel) SURFboard 1000 internal
	255	cable modem. This is an ISA card which is used by a number of cable
	256	TV companies to provide cable modem access. It's a one-way
	257	downstream-only cable modem, meaning that your upstream net link is
	258	provided by your regular phone modem.
	259
	260	At present this driver only compiles as a module, so say M here if
	261	you have this card. The module will be called sb1000. Then read
	262	<file:Documentation/networking/README.sb1000> for information on how
	263	to use this module, as it needs special ppp scripts for establishing
	264	a connection. Further documentation and the necessary scripts can be
	265	found at:
	266
	267	<http://www.jacksonville.net/~fventuri/>
	268	<http://home.adelphia.net/~siglercm/sb1000.html>
	269	<http://linuxpower.cx/~cable/>
	270
	271	If you don't have this card, of course say N.
	272
00db8189 AF	273	source "drivers/net/phy/Kconfig"
00db8189 AF	274
18e635f4 JK	275	source "drivers/net/plip/Kconfig"
18e635f4 JK	276
88491d81 JK	277	source "drivers/net/ppp/Kconfig"
88491d81 JK	278
b5451d78 JK	279	source "drivers/net/slip/Kconfig"
b5451d78 JK	280
88491d81 JK	281	source "drivers/s390/net/Kconfig"
88491d81 JK	282
88491d81 JK	283	source "drivers/net/usb/Kconfig"
88491d81 JK	284
1da177e4 LT	285	source "drivers/net/wireless/Kconfig"
1da177e4 LT	286
143ee2d5 IPG	287	source "drivers/net/wimax/Kconfig"
143ee2d5 IPG	288
1da177e4 LT	289	source "drivers/net/wan/Kconfig"
1da177e4 LT	290
0739d643	291	source "drivers/net/ieee802154/Kconfig"
0739d643	292
0d160211 JF	293	config XEN_NETDEV_FRONTEND
	294	tristate "Xen network device frontend driver"
	295	depends on XEN
7003087c	296	select XEN_XENBUS_FRONTEND
0d160211 JF	297	default y
0d160211 JF	298	help
f942dc25 IC	299	This driver provides support for Xen paravirtual network
	300	devices exported by a Xen network driver domain (often
	301	domain 0).
	302
	303	The corresponding Linux backend driver is enabled by the
	304	CONFIG_XEN_NETDEV_BACKEND option.
	305
	306	If you are compiling a kernel for use as Xen guest, you
	307	should say Y here. To compile this driver as a module, chose
	308	M here: the module will be called xen-netfront.
	309
	310	config XEN_NETDEV_BACKEND
	311	tristate "Xen backend network device"
	312	depends on XEN_BACKEND
	313	help
	314	This driver allows the kernel to act as a Xen network driver
	315	domain which exports paravirtual network devices to other
	316	Xen domains. These devices can be accessed by any operating
	317	system that implements a compatible front end.
	318
	319	The corresponding Linux frontend driver is enabled by the
	320	CONFIG_XEN_NETDEV_FRONTEND configuration option.
	321
	322	The backend driver presents a standard network device
	323	endpoint for each paravirtual network device to the driver
	324	domain network stack. These can then be bridged or routed
	325	etc in order to provide full network connectivity.
	326
	327	If you are compiling a kernel to run in a Xen network driver
	328	domain (often this is domain 0) you should say Y here. To
	329	compile this driver as a module, chose M here: the module
	330	will be called xen-netback.
0d160211	331
d1a890fa	332	config VMXNET3
e85eb117 PDM	333	tristate "VMware VMXNET3 ethernet driver"
	334	depends on PCI && INET
	335	help
	336	This driver supports VMware's vmxnet3 virtual ethernet NIC.
	337	To compile this driver as a module, choose M here: the
	338	module will be called vmxnet3.
d1a890fa	339
95fa0405 HZ	340	source "drivers/net/hyperv/Kconfig"
95fa0405 HZ	341
d1c0a65f	342	endif # NETDEVICES