]>
Commit | Line | Data |
---|---|---|
1da177e4 LT |
1 | /* |
2 | * This program is free software; you can redistribute it and/or | |
3 | * modify it under the terms of the GNU General Public License | |
4 | * as published by the Free Software Foundation; either version | |
5 | * 2 of the License, or (at your option) any later version. | |
6 | * | |
7 | * (c) Copyright 1998 Alan Cox <alan@lxorguk.ukuu.org.uk> | |
8 | * (c) Copyright 2000, 2001 Red Hat Inc | |
9 | * | |
10 | * Development of this driver was funded by Equiinet Ltd | |
11 | * http://www.equiinet.com | |
12 | * | |
13 | * ChangeLog: | |
14 | * | |
15 | * Asynchronous mode dropped for 2.2. For 2.5 we will attempt the | |
16 | * unification of all the Z85x30 asynchronous drivers for real. | |
17 | * | |
18 | * DMA now uses get_free_page as kmalloc buffers may span a 64K | |
19 | * boundary. | |
20 | * | |
113aa838 AC |
21 | * Modified for SMP safety and SMP locking by Alan Cox |
22 | * <alan@lxorguk.ukuu.org.uk> | |
1da177e4 LT |
23 | * |
24 | * Performance | |
25 | * | |
26 | * Z85230: | |
27 | * Non DMA you want a 486DX50 or better to do 64Kbits. 9600 baud | |
28 | * X.25 is not unrealistic on all machines. DMA mode can in theory | |
29 | * handle T1/E1 quite nicely. In practice the limit seems to be about | |
30 | * 512Kbit->1Mbit depending on motherboard. | |
31 | * | |
32 | * Z85C30: | |
33 | * 64K will take DMA, 9600 baud X.25 should be ok. | |
34 | * | |
35 | * Z8530: | |
36 | * Synchronous mode without DMA is unlikely to pass about 2400 baud. | |
37 | */ | |
38 | ||
39 | #include <linux/module.h> | |
40 | #include <linux/kernel.h> | |
41 | #include <linux/mm.h> | |
42 | #include <linux/net.h> | |
43 | #include <linux/skbuff.h> | |
44 | #include <linux/netdevice.h> | |
45 | #include <linux/if_arp.h> | |
46 | #include <linux/delay.h> | |
52e8a6a2 | 47 | #include <linux/hdlc.h> |
1da177e4 LT |
48 | #include <linux/ioport.h> |
49 | #include <linux/init.h> | |
5a0e3ad6 | 50 | #include <linux/gfp.h> |
1da177e4 LT |
51 | #include <asm/dma.h> |
52 | #include <asm/io.h> | |
53 | #define RT_LOCK | |
54 | #define RT_UNLOCK | |
55 | #include <linux/spinlock.h> | |
56 | ||
1da177e4 LT |
57 | #include "z85230.h" |
58 | ||
59 | ||
60 | /** | |
61 | * z8530_read_port - Architecture specific interface function | |
62 | * @p: port to read | |
63 | * | |
64 | * Provided port access methods. The Comtrol SV11 requires no delays | |
65 | * between accesses and uses PC I/O. Some drivers may need a 5uS delay | |
66 | * | |
67 | * In the longer term this should become an architecture specific | |
68 | * section so that this can become a generic driver interface for all | |
69 | * platforms. For now we only handle PC I/O ports with or without the | |
70 | * dread 5uS sanity delay. | |
71 | * | |
72 | * The caller must hold sufficient locks to avoid violating the horrible | |
73 | * 5uS delay rule. | |
74 | */ | |
75 | ||
76 | static inline int z8530_read_port(unsigned long p) | |
77 | { | |
78 | u8 r=inb(Z8530_PORT_OF(p)); | |
79 | if(p&Z8530_PORT_SLEEP) /* gcc should figure this out efficiently ! */ | |
80 | udelay(5); | |
81 | return r; | |
82 | } | |
83 | ||
84 | /** | |
85 | * z8530_write_port - Architecture specific interface function | |
86 | * @p: port to write | |
87 | * @d: value to write | |
88 | * | |
89 | * Write a value to a port with delays if need be. Note that the | |
90 | * caller must hold locks to avoid read/writes from other contexts | |
91 | * violating the 5uS rule | |
92 | * | |
93 | * In the longer term this should become an architecture specific | |
94 | * section so that this can become a generic driver interface for all | |
95 | * platforms. For now we only handle PC I/O ports with or without the | |
96 | * dread 5uS sanity delay. | |
97 | */ | |
98 | ||
99 | ||
100 | static inline void z8530_write_port(unsigned long p, u8 d) | |
101 | { | |
102 | outb(d,Z8530_PORT_OF(p)); | |
103 | if(p&Z8530_PORT_SLEEP) | |
104 | udelay(5); | |
105 | } | |
106 | ||
107 | ||
108 | ||
109 | static void z8530_rx_done(struct z8530_channel *c); | |
110 | static void z8530_tx_done(struct z8530_channel *c); | |
111 | ||
112 | ||
113 | /** | |
114 | * read_zsreg - Read a register from a Z85230 | |
115 | * @c: Z8530 channel to read from (2 per chip) | |
116 | * @reg: Register to read | |
117 | * FIXME: Use a spinlock. | |
118 | * | |
119 | * Most of the Z8530 registers are indexed off the control registers. | |
120 | * A read is done by writing to the control register and reading the | |
121 | * register back. The caller must hold the lock | |
122 | */ | |
123 | ||
124 | static inline u8 read_zsreg(struct z8530_channel *c, u8 reg) | |
125 | { | |
126 | if(reg) | |
127 | z8530_write_port(c->ctrlio, reg); | |
128 | return z8530_read_port(c->ctrlio); | |
129 | } | |
130 | ||
131 | /** | |
132 | * read_zsdata - Read the data port of a Z8530 channel | |
133 | * @c: The Z8530 channel to read the data port from | |
134 | * | |
135 | * The data port provides fast access to some things. We still | |
136 | * have all the 5uS delays to worry about. | |
137 | */ | |
138 | ||
139 | static inline u8 read_zsdata(struct z8530_channel *c) | |
140 | { | |
141 | u8 r; | |
142 | r=z8530_read_port(c->dataio); | |
143 | return r; | |
144 | } | |
145 | ||
146 | /** | |
147 | * write_zsreg - Write to a Z8530 channel register | |
148 | * @c: The Z8530 channel | |
149 | * @reg: Register number | |
150 | * @val: Value to write | |
151 | * | |
152 | * Write a value to an indexed register. The caller must hold the lock | |
153 | * to honour the irritating delay rules. We know about register 0 | |
154 | * being fast to access. | |
155 | * | |
156 | * Assumes c->lock is held. | |
157 | */ | |
158 | static inline void write_zsreg(struct z8530_channel *c, u8 reg, u8 val) | |
159 | { | |
160 | if(reg) | |
161 | z8530_write_port(c->ctrlio, reg); | |
162 | z8530_write_port(c->ctrlio, val); | |
163 | ||
164 | } | |
165 | ||
166 | /** | |
167 | * write_zsctrl - Write to a Z8530 control register | |
168 | * @c: The Z8530 channel | |
169 | * @val: Value to write | |
170 | * | |
171 | * Write directly to the control register on the Z8530 | |
172 | */ | |
173 | ||
174 | static inline void write_zsctrl(struct z8530_channel *c, u8 val) | |
175 | { | |
176 | z8530_write_port(c->ctrlio, val); | |
177 | } | |
178 | ||
179 | /** | |
180 | * write_zsdata - Write to a Z8530 control register | |
181 | * @c: The Z8530 channel | |
182 | * @val: Value to write | |
183 | * | |
184 | * Write directly to the data register on the Z8530 | |
185 | */ | |
186 | ||
187 | ||
188 | static inline void write_zsdata(struct z8530_channel *c, u8 val) | |
189 | { | |
190 | z8530_write_port(c->dataio, val); | |
191 | } | |
192 | ||
193 | /* | |
194 | * Register loading parameters for a dead port | |
195 | */ | |
196 | ||
197 | u8 z8530_dead_port[]= | |
198 | { | |
199 | 255 | |
200 | }; | |
201 | ||
202 | EXPORT_SYMBOL(z8530_dead_port); | |
203 | ||
204 | /* | |
205 | * Register loading parameters for currently supported circuit types | |
206 | */ | |
207 | ||
208 | ||
209 | /* | |
210 | * Data clocked by telco end. This is the correct data for the UK | |
211 | * "kilostream" service, and most other similar services. | |
212 | */ | |
213 | ||
214 | u8 z8530_hdlc_kilostream[]= | |
215 | { | |
216 | 4, SYNC_ENAB|SDLC|X1CLK, | |
217 | 2, 0, /* No vector */ | |
218 | 1, 0, | |
219 | 3, ENT_HM|RxCRC_ENAB|Rx8, | |
220 | 5, TxCRC_ENAB|RTS|TxENAB|Tx8|DTR, | |
221 | 9, 0, /* Disable interrupts */ | |
222 | 6, 0xFF, | |
223 | 7, FLAG, | |
224 | 10, ABUNDER|NRZ|CRCPS,/*MARKIDLE ??*/ | |
225 | 11, TCTRxCP, | |
226 | 14, DISDPLL, | |
227 | 15, DCDIE|SYNCIE|CTSIE|TxUIE|BRKIE, | |
228 | 1, EXT_INT_ENAB|TxINT_ENAB|INT_ALL_Rx, | |
229 | 9, NV|MIE|NORESET, | |
230 | 255 | |
231 | }; | |
232 | ||
233 | EXPORT_SYMBOL(z8530_hdlc_kilostream); | |
234 | ||
235 | /* | |
236 | * As above but for enhanced chips. | |
237 | */ | |
238 | ||
239 | u8 z8530_hdlc_kilostream_85230[]= | |
240 | { | |
241 | 4, SYNC_ENAB|SDLC|X1CLK, | |
242 | 2, 0, /* No vector */ | |
243 | 1, 0, | |
244 | 3, ENT_HM|RxCRC_ENAB|Rx8, | |
245 | 5, TxCRC_ENAB|RTS|TxENAB|Tx8|DTR, | |
246 | 9, 0, /* Disable interrupts */ | |
247 | 6, 0xFF, | |
248 | 7, FLAG, | |
249 | 10, ABUNDER|NRZ|CRCPS, /* MARKIDLE?? */ | |
250 | 11, TCTRxCP, | |
251 | 14, DISDPLL, | |
252 | 15, DCDIE|SYNCIE|CTSIE|TxUIE|BRKIE, | |
253 | 1, EXT_INT_ENAB|TxINT_ENAB|INT_ALL_Rx, | |
254 | 9, NV|MIE|NORESET, | |
255 | 23, 3, /* Extended mode AUTO TX and EOM*/ | |
256 | ||
257 | 255 | |
258 | }; | |
259 | ||
260 | EXPORT_SYMBOL(z8530_hdlc_kilostream_85230); | |
261 | ||
262 | /** | |
263 | * z8530_flush_fifo - Flush on chip RX FIFO | |
264 | * @c: Channel to flush | |
265 | * | |
266 | * Flush the receive FIFO. There is no specific option for this, we | |
267 | * blindly read bytes and discard them. Reading when there is no data | |
268 | * is harmless. The 8530 has a 4 byte FIFO, the 85230 has 8 bytes. | |
269 | * | |
270 | * All locking is handled for the caller. On return data may still be | |
271 | * present if it arrived during the flush. | |
272 | */ | |
273 | ||
274 | static void z8530_flush_fifo(struct z8530_channel *c) | |
275 | { | |
276 | read_zsreg(c, R1); | |
277 | read_zsreg(c, R1); | |
278 | read_zsreg(c, R1); | |
279 | read_zsreg(c, R1); | |
280 | if(c->dev->type==Z85230) | |
281 | { | |
282 | read_zsreg(c, R1); | |
283 | read_zsreg(c, R1); | |
284 | read_zsreg(c, R1); | |
285 | read_zsreg(c, R1); | |
286 | } | |
287 | } | |
288 | ||
289 | /** | |
290 | * z8530_rtsdtr - Control the outgoing DTS/RTS line | |
291 | * @c: The Z8530 channel to control; | |
292 | * @set: 1 to set, 0 to clear | |
293 | * | |
294 | * Sets or clears DTR/RTS on the requested line. All locking is handled | |
295 | * by the caller. For now we assume all boards use the actual RTS/DTR | |
296 | * on the chip. Apparently one or two don't. We'll scream about them | |
297 | * later. | |
298 | */ | |
299 | ||
300 | static void z8530_rtsdtr(struct z8530_channel *c, int set) | |
301 | { | |
302 | if (set) | |
303 | c->regs[5] |= (RTS | DTR); | |
304 | else | |
305 | c->regs[5] &= ~(RTS | DTR); | |
306 | write_zsreg(c, R5, c->regs[5]); | |
307 | } | |
308 | ||
309 | /** | |
310 | * z8530_rx - Handle a PIO receive event | |
311 | * @c: Z8530 channel to process | |
312 | * | |
313 | * Receive handler for receiving in PIO mode. This is much like the | |
314 | * async one but not quite the same or as complex | |
315 | * | |
316 | * Note: Its intended that this handler can easily be separated from | |
317 | * the main code to run realtime. That'll be needed for some machines | |
318 | * (eg to ever clock 64kbits on a sparc ;)). | |
319 | * | |
320 | * The RT_LOCK macros don't do anything now. Keep the code covered | |
321 | * by them as short as possible in all circumstances - clocks cost | |
322 | * baud. The interrupt handler is assumed to be atomic w.r.t. to | |
323 | * other code - this is true in the RT case too. | |
324 | * | |
325 | * We only cover the sync cases for this. If you want 2Mbit async | |
326 | * do it yourself but consider medical assistance first. This non DMA | |
327 | * synchronous mode is portable code. The DMA mode assumes PCI like | |
328 | * ISA DMA | |
329 | * | |
330 | * Called with the device lock held | |
331 | */ | |
332 | ||
333 | static void z8530_rx(struct z8530_channel *c) | |
334 | { | |
335 | u8 ch,stat; | |
45d3ac4e | 336 | |
1da177e4 LT |
337 | while(1) |
338 | { | |
339 | /* FIFO empty ? */ | |
340 | if(!(read_zsreg(c, R0)&1)) | |
341 | break; | |
342 | ch=read_zsdata(c); | |
343 | stat=read_zsreg(c, R1); | |
344 | ||
345 | /* | |
346 | * Overrun ? | |
347 | */ | |
348 | if(c->count < c->max) | |
349 | { | |
350 | *c->dptr++=ch; | |
351 | c->count++; | |
352 | } | |
353 | ||
354 | if(stat&END_FR) | |
355 | { | |
356 | ||
357 | /* | |
358 | * Error ? | |
359 | */ | |
360 | if(stat&(Rx_OVR|CRC_ERR)) | |
361 | { | |
362 | /* Rewind the buffer and return */ | |
363 | if(c->skb) | |
364 | c->dptr=c->skb->data; | |
365 | c->count=0; | |
366 | if(stat&Rx_OVR) | |
367 | { | |
368 | printk(KERN_WARNING "%s: overrun\n", c->dev->name); | |
369 | c->rx_overrun++; | |
370 | } | |
371 | if(stat&CRC_ERR) | |
372 | { | |
373 | c->rx_crc_err++; | |
374 | /* printk("crc error\n"); */ | |
375 | } | |
376 | /* Shove the frame upstream */ | |
377 | } | |
378 | else | |
379 | { | |
380 | /* | |
381 | * Drop the lock for RX processing, or | |
382 | * there are deadlocks | |
383 | */ | |
384 | z8530_rx_done(c); | |
385 | write_zsctrl(c, RES_Rx_CRC); | |
386 | } | |
387 | } | |
388 | } | |
389 | /* | |
390 | * Clear irq | |
391 | */ | |
392 | write_zsctrl(c, ERR_RES); | |
393 | write_zsctrl(c, RES_H_IUS); | |
1da177e4 LT |
394 | } |
395 | ||
396 | ||
397 | /** | |
398 | * z8530_tx - Handle a PIO transmit event | |
399 | * @c: Z8530 channel to process | |
400 | * | |
401 | * Z8530 transmit interrupt handler for the PIO mode. The basic | |
402 | * idea is to attempt to keep the FIFO fed. We fill as many bytes | |
403 | * in as possible, its quite possible that we won't keep up with the | |
404 | * data rate otherwise. | |
405 | */ | |
406 | ||
407 | static void z8530_tx(struct z8530_channel *c) | |
408 | { | |
1da177e4 LT |
409 | while(c->txcount) { |
410 | /* FIFO full ? */ | |
411 | if(!(read_zsreg(c, R0)&4)) | |
fe797455 | 412 | return; |
1da177e4 LT |
413 | c->txcount--; |
414 | /* | |
415 | * Shovel out the byte | |
416 | */ | |
417 | write_zsreg(c, R8, *c->tx_ptr++); | |
418 | write_zsctrl(c, RES_H_IUS); | |
419 | /* We are about to underflow */ | |
420 | if(c->txcount==0) | |
421 | { | |
422 | write_zsctrl(c, RES_EOM_L); | |
423 | write_zsreg(c, R10, c->regs[10]&~ABUNDER); | |
424 | } | |
425 | } | |
426 | ||
427 | ||
428 | /* | |
429 | * End of frame TX - fire another one | |
430 | */ | |
431 | ||
432 | write_zsctrl(c, RES_Tx_P); | |
433 | ||
434 | z8530_tx_done(c); | |
435 | write_zsctrl(c, RES_H_IUS); | |
1da177e4 LT |
436 | } |
437 | ||
438 | /** | |
439 | * z8530_status - Handle a PIO status exception | |
440 | * @chan: Z8530 channel to process | |
441 | * | |
442 | * A status event occurred in PIO synchronous mode. There are several | |
443 | * reasons the chip will bother us here. A transmit underrun means we | |
444 | * failed to feed the chip fast enough and just broke a packet. A DCD | |
52e8a6a2 | 445 | * change is a line up or down. |
1da177e4 LT |
446 | */ |
447 | ||
448 | static void z8530_status(struct z8530_channel *chan) | |
449 | { | |
450 | u8 status, altered; | |
451 | ||
52e8a6a2 KH |
452 | status = read_zsreg(chan, R0); |
453 | altered = chan->status ^ status; | |
454 | ||
455 | chan->status = status; | |
456 | ||
457 | if (status & TxEOM) { | |
1da177e4 | 458 | /* printk("%s: Tx underrun.\n", chan->dev->name); */ |
52e8a6a2 | 459 | chan->netdevice->stats.tx_fifo_errors++; |
1da177e4 LT |
460 | write_zsctrl(chan, ERR_RES); |
461 | z8530_tx_done(chan); | |
462 | } | |
52e8a6a2 KH |
463 | |
464 | if (altered & chan->dcdcheck) | |
1da177e4 | 465 | { |
52e8a6a2 | 466 | if (status & chan->dcdcheck) { |
1da177e4 | 467 | printk(KERN_INFO "%s: DCD raised\n", chan->dev->name); |
52e8a6a2 KH |
468 | write_zsreg(chan, R3, chan->regs[3] | RxENABLE); |
469 | if (chan->netdevice) | |
470 | netif_carrier_on(chan->netdevice); | |
471 | } else { | |
1da177e4 | 472 | printk(KERN_INFO "%s: DCD lost\n", chan->dev->name); |
52e8a6a2 | 473 | write_zsreg(chan, R3, chan->regs[3] & ~RxENABLE); |
1da177e4 | 474 | z8530_flush_fifo(chan); |
52e8a6a2 KH |
475 | if (chan->netdevice) |
476 | netif_carrier_off(chan->netdevice); | |
1da177e4 | 477 | } |
52e8a6a2 KH |
478 | |
479 | } | |
1da177e4 LT |
480 | write_zsctrl(chan, RES_EXT_INT); |
481 | write_zsctrl(chan, RES_H_IUS); | |
1da177e4 LT |
482 | } |
483 | ||
52e8a6a2 | 484 | struct z8530_irqhandler z8530_sync = |
1da177e4 LT |
485 | { |
486 | z8530_rx, | |
487 | z8530_tx, | |
488 | z8530_status | |
489 | }; | |
490 | ||
491 | EXPORT_SYMBOL(z8530_sync); | |
492 | ||
493 | /** | |
494 | * z8530_dma_rx - Handle a DMA RX event | |
495 | * @chan: Channel to handle | |
496 | * | |
497 | * Non bus mastering DMA interfaces for the Z8x30 devices. This | |
498 | * is really pretty PC specific. The DMA mode means that most receive | |
499 | * events are handled by the DMA hardware. We get a kick here only if | |
500 | * a frame ended. | |
501 | */ | |
502 | ||
503 | static void z8530_dma_rx(struct z8530_channel *chan) | |
504 | { | |
1da177e4 LT |
505 | if(chan->rxdma_on) |
506 | { | |
507 | /* Special condition check only */ | |
508 | u8 status; | |
509 | ||
510 | read_zsreg(chan, R7); | |
511 | read_zsreg(chan, R6); | |
512 | ||
513 | status=read_zsreg(chan, R1); | |
514 | ||
515 | if(status&END_FR) | |
516 | { | |
517 | z8530_rx_done(chan); /* Fire up the next one */ | |
518 | } | |
519 | write_zsctrl(chan, ERR_RES); | |
520 | write_zsctrl(chan, RES_H_IUS); | |
521 | } | |
522 | else | |
523 | { | |
524 | /* DMA is off right now, drain the slow way */ | |
525 | z8530_rx(chan); | |
526 | } | |
1da177e4 LT |
527 | } |
528 | ||
529 | /** | |
530 | * z8530_dma_tx - Handle a DMA TX event | |
531 | * @chan: The Z8530 channel to handle | |
532 | * | |
533 | * We have received an interrupt while doing DMA transmissions. It | |
534 | * shouldn't happen. Scream loudly if it does. | |
535 | */ | |
536 | ||
537 | static void z8530_dma_tx(struct z8530_channel *chan) | |
538 | { | |
1da177e4 LT |
539 | if(!chan->dma_tx) |
540 | { | |
541 | printk(KERN_WARNING "Hey who turned the DMA off?\n"); | |
542 | z8530_tx(chan); | |
543 | return; | |
544 | } | |
545 | /* This shouldnt occur in DMA mode */ | |
546 | printk(KERN_ERR "DMA tx - bogus event!\n"); | |
547 | z8530_tx(chan); | |
1da177e4 LT |
548 | } |
549 | ||
550 | /** | |
551 | * z8530_dma_status - Handle a DMA status exception | |
552 | * @chan: Z8530 channel to process | |
553 | * | |
554 | * A status event occurred on the Z8530. We receive these for two reasons | |
555 | * when in DMA mode. Firstly if we finished a packet transfer we get one | |
52e8a6a2 | 556 | * and kick the next packet out. Secondly we may see a DCD change. |
1da177e4 LT |
557 | * |
558 | */ | |
559 | ||
560 | static void z8530_dma_status(struct z8530_channel *chan) | |
561 | { | |
562 | u8 status, altered; | |
563 | ||
564 | status=read_zsreg(chan, R0); | |
565 | altered=chan->status^status; | |
566 | ||
567 | chan->status=status; | |
568 | ||
569 | ||
570 | if(chan->dma_tx) | |
571 | { | |
572 | if(status&TxEOM) | |
573 | { | |
574 | unsigned long flags; | |
575 | ||
576 | flags=claim_dma_lock(); | |
577 | disable_dma(chan->txdma); | |
578 | clear_dma_ff(chan->txdma); | |
579 | chan->txdma_on=0; | |
580 | release_dma_lock(flags); | |
581 | z8530_tx_done(chan); | |
582 | } | |
583 | } | |
584 | ||
52e8a6a2 | 585 | if (altered & chan->dcdcheck) |
1da177e4 | 586 | { |
52e8a6a2 | 587 | if (status & chan->dcdcheck) { |
1da177e4 | 588 | printk(KERN_INFO "%s: DCD raised\n", chan->dev->name); |
52e8a6a2 KH |
589 | write_zsreg(chan, R3, chan->regs[3] | RxENABLE); |
590 | if (chan->netdevice) | |
591 | netif_carrier_on(chan->netdevice); | |
592 | } else { | |
1da177e4 | 593 | printk(KERN_INFO "%s:DCD lost\n", chan->dev->name); |
52e8a6a2 | 594 | write_zsreg(chan, R3, chan->regs[3] & ~RxENABLE); |
1da177e4 | 595 | z8530_flush_fifo(chan); |
52e8a6a2 KH |
596 | if (chan->netdevice) |
597 | netif_carrier_off(chan->netdevice); | |
1da177e4 | 598 | } |
52e8a6a2 | 599 | } |
1da177e4 LT |
600 | |
601 | write_zsctrl(chan, RES_EXT_INT); | |
602 | write_zsctrl(chan, RES_H_IUS); | |
1da177e4 LT |
603 | } |
604 | ||
62c5345d | 605 | static struct z8530_irqhandler z8530_dma_sync = { |
1da177e4 LT |
606 | z8530_dma_rx, |
607 | z8530_dma_tx, | |
608 | z8530_dma_status | |
609 | }; | |
610 | ||
62c5345d | 611 | static struct z8530_irqhandler z8530_txdma_sync = { |
1da177e4 LT |
612 | z8530_rx, |
613 | z8530_dma_tx, | |
614 | z8530_dma_status | |
615 | }; | |
616 | ||
1da177e4 LT |
617 | /** |
618 | * z8530_rx_clear - Handle RX events from a stopped chip | |
619 | * @c: Z8530 channel to shut up | |
620 | * | |
621 | * Receive interrupt vectors for a Z8530 that is in 'parked' mode. | |
622 | * For machines with PCI Z85x30 cards, or level triggered interrupts | |
623 | * (eg the MacII) we must clear the interrupt cause or die. | |
624 | */ | |
625 | ||
626 | ||
627 | static void z8530_rx_clear(struct z8530_channel *c) | |
628 | { | |
629 | /* | |
630 | * Data and status bytes | |
631 | */ | |
632 | u8 stat; | |
633 | ||
634 | read_zsdata(c); | |
635 | stat=read_zsreg(c, R1); | |
636 | ||
637 | if(stat&END_FR) | |
638 | write_zsctrl(c, RES_Rx_CRC); | |
639 | /* | |
640 | * Clear irq | |
641 | */ | |
642 | write_zsctrl(c, ERR_RES); | |
643 | write_zsctrl(c, RES_H_IUS); | |
644 | } | |
645 | ||
646 | /** | |
647 | * z8530_tx_clear - Handle TX events from a stopped chip | |
648 | * @c: Z8530 channel to shut up | |
649 | * | |
650 | * Transmit interrupt vectors for a Z8530 that is in 'parked' mode. | |
651 | * For machines with PCI Z85x30 cards, or level triggered interrupts | |
652 | * (eg the MacII) we must clear the interrupt cause or die. | |
653 | */ | |
654 | ||
655 | static void z8530_tx_clear(struct z8530_channel *c) | |
656 | { | |
657 | write_zsctrl(c, RES_Tx_P); | |
658 | write_zsctrl(c, RES_H_IUS); | |
659 | } | |
660 | ||
661 | /** | |
662 | * z8530_status_clear - Handle status events from a stopped chip | |
663 | * @chan: Z8530 channel to shut up | |
664 | * | |
665 | * Status interrupt vectors for a Z8530 that is in 'parked' mode. | |
666 | * For machines with PCI Z85x30 cards, or level triggered interrupts | |
667 | * (eg the MacII) we must clear the interrupt cause or die. | |
668 | */ | |
669 | ||
670 | static void z8530_status_clear(struct z8530_channel *chan) | |
671 | { | |
672 | u8 status=read_zsreg(chan, R0); | |
673 | if(status&TxEOM) | |
674 | write_zsctrl(chan, ERR_RES); | |
675 | write_zsctrl(chan, RES_EXT_INT); | |
676 | write_zsctrl(chan, RES_H_IUS); | |
677 | } | |
678 | ||
679 | struct z8530_irqhandler z8530_nop= | |
680 | { | |
681 | z8530_rx_clear, | |
682 | z8530_tx_clear, | |
683 | z8530_status_clear | |
684 | }; | |
685 | ||
686 | ||
687 | EXPORT_SYMBOL(z8530_nop); | |
688 | ||
689 | /** | |
690 | * z8530_interrupt - Handle an interrupt from a Z8530 | |
691 | * @irq: Interrupt number | |
692 | * @dev_id: The Z8530 device that is interrupting. | |
1da177e4 LT |
693 | * |
694 | * A Z85[2]30 device has stuck its hand in the air for attention. | |
695 | * We scan both the channels on the chip for events and then call | |
696 | * the channel specific call backs for each channel that has events. | |
697 | * We have to use callback functions because the two channels can be | |
698 | * in different modes. | |
699 | * | |
700 | * Locking is done for the handlers. Note that locking is done | |
701 | * at the chip level (the 5uS delay issue is per chip not per | |
702 | * channel). c->lock for both channels points to dev->lock | |
703 | */ | |
704 | ||
7d12e780 | 705 | irqreturn_t z8530_interrupt(int irq, void *dev_id) |
1da177e4 LT |
706 | { |
707 | struct z8530_dev *dev=dev_id; | |
4174439e | 708 | u8 uninitialized_var(intr); |
1da177e4 LT |
709 | static volatile int locker=0; |
710 | int work=0; | |
711 | struct z8530_irqhandler *irqs; | |
712 | ||
713 | if(locker) | |
714 | { | |
715 | printk(KERN_ERR "IRQ re-enter\n"); | |
716 | return IRQ_NONE; | |
717 | } | |
718 | locker=1; | |
719 | ||
720 | spin_lock(&dev->lock); | |
721 | ||
722 | while(++work<5000) | |
723 | { | |
724 | ||
725 | intr = read_zsreg(&dev->chanA, R3); | |
726 | if(!(intr & (CHARxIP|CHATxIP|CHAEXT|CHBRxIP|CHBTxIP|CHBEXT))) | |
727 | break; | |
728 | ||
729 | /* This holds the IRQ status. On the 8530 you must read it from chan | |
730 | A even though it applies to the whole chip */ | |
731 | ||
732 | /* Now walk the chip and see what it is wanting - it may be | |
733 | an IRQ for someone else remember */ | |
734 | ||
735 | irqs=dev->chanA.irqs; | |
736 | ||
737 | if(intr & (CHARxIP|CHATxIP|CHAEXT)) | |
738 | { | |
739 | if(intr&CHARxIP) | |
740 | irqs->rx(&dev->chanA); | |
741 | if(intr&CHATxIP) | |
742 | irqs->tx(&dev->chanA); | |
743 | if(intr&CHAEXT) | |
744 | irqs->status(&dev->chanA); | |
745 | } | |
746 | ||
747 | irqs=dev->chanB.irqs; | |
748 | ||
749 | if(intr & (CHBRxIP|CHBTxIP|CHBEXT)) | |
750 | { | |
751 | if(intr&CHBRxIP) | |
752 | irqs->rx(&dev->chanB); | |
753 | if(intr&CHBTxIP) | |
754 | irqs->tx(&dev->chanB); | |
755 | if(intr&CHBEXT) | |
756 | irqs->status(&dev->chanB); | |
757 | } | |
758 | } | |
759 | spin_unlock(&dev->lock); | |
760 | if(work==5000) | |
761 | printk(KERN_ERR "%s: interrupt jammed - abort(0x%X)!\n", dev->name, intr); | |
762 | /* Ok all done */ | |
763 | locker=0; | |
764 | return IRQ_HANDLED; | |
765 | } | |
766 | ||
767 | EXPORT_SYMBOL(z8530_interrupt); | |
768 | ||
769 | static char reg_init[16]= | |
770 | { | |
771 | 0,0,0,0, | |
772 | 0,0,0,0, | |
773 | 0,0,0,0, | |
774 | 0x55,0,0,0 | |
775 | }; | |
776 | ||
777 | ||
778 | /** | |
779 | * z8530_sync_open - Open a Z8530 channel for PIO | |
780 | * @dev: The network interface we are using | |
781 | * @c: The Z8530 channel to open in synchronous PIO mode | |
782 | * | |
783 | * Switch a Z8530 into synchronous mode without DMA assist. We | |
784 | * raise the RTS/DTR and commence network operation. | |
785 | */ | |
786 | ||
787 | int z8530_sync_open(struct net_device *dev, struct z8530_channel *c) | |
788 | { | |
789 | unsigned long flags; | |
790 | ||
791 | spin_lock_irqsave(c->lock, flags); | |
792 | ||
793 | c->sync = 1; | |
794 | c->mtu = dev->mtu+64; | |
795 | c->count = 0; | |
796 | c->skb = NULL; | |
797 | c->skb2 = NULL; | |
798 | c->irqs = &z8530_sync; | |
799 | ||
800 | /* This loads the double buffer up */ | |
801 | z8530_rx_done(c); /* Load the frame ring */ | |
802 | z8530_rx_done(c); /* Load the backup frame */ | |
803 | z8530_rtsdtr(c,1); | |
804 | c->dma_tx = 0; | |
805 | c->regs[R1]|=TxINT_ENAB; | |
806 | write_zsreg(c, R1, c->regs[R1]); | |
807 | write_zsreg(c, R3, c->regs[R3]|RxENABLE); | |
808 | ||
809 | spin_unlock_irqrestore(c->lock, flags); | |
810 | return 0; | |
811 | } | |
812 | ||
813 | ||
814 | EXPORT_SYMBOL(z8530_sync_open); | |
815 | ||
816 | /** | |
817 | * z8530_sync_close - Close a PIO Z8530 channel | |
818 | * @dev: Network device to close | |
819 | * @c: Z8530 channel to disassociate and move to idle | |
820 | * | |
821 | * Close down a Z8530 interface and switch its interrupt handlers | |
822 | * to discard future events. | |
823 | */ | |
824 | ||
825 | int z8530_sync_close(struct net_device *dev, struct z8530_channel *c) | |
826 | { | |
827 | u8 chk; | |
828 | unsigned long flags; | |
829 | ||
830 | spin_lock_irqsave(c->lock, flags); | |
831 | c->irqs = &z8530_nop; | |
832 | c->max = 0; | |
833 | c->sync = 0; | |
834 | ||
835 | chk=read_zsreg(c,R0); | |
836 | write_zsreg(c, R3, c->regs[R3]); | |
837 | z8530_rtsdtr(c,0); | |
838 | ||
839 | spin_unlock_irqrestore(c->lock, flags); | |
840 | return 0; | |
841 | } | |
842 | ||
843 | EXPORT_SYMBOL(z8530_sync_close); | |
844 | ||
845 | /** | |
846 | * z8530_sync_dma_open - Open a Z8530 for DMA I/O | |
847 | * @dev: The network device to attach | |
848 | * @c: The Z8530 channel to configure in sync DMA mode. | |
849 | * | |
850 | * Set up a Z85x30 device for synchronous DMA in both directions. Two | |
851 | * ISA DMA channels must be available for this to work. We assume ISA | |
852 | * DMA driven I/O and PC limits on access. | |
853 | */ | |
854 | ||
855 | int z8530_sync_dma_open(struct net_device *dev, struct z8530_channel *c) | |
856 | { | |
857 | unsigned long cflags, dflags; | |
858 | ||
859 | c->sync = 1; | |
860 | c->mtu = dev->mtu+64; | |
861 | c->count = 0; | |
862 | c->skb = NULL; | |
863 | c->skb2 = NULL; | |
864 | /* | |
865 | * Load the DMA interfaces up | |
866 | */ | |
867 | c->rxdma_on = 0; | |
868 | c->txdma_on = 0; | |
869 | ||
870 | /* | |
871 | * Allocate the DMA flip buffers. Limit by page size. | |
872 | * Everyone runs 1500 mtu or less on wan links so this | |
873 | * should be fine. | |
874 | */ | |
875 | ||
876 | if(c->mtu > PAGE_SIZE/2) | |
877 | return -EMSGSIZE; | |
878 | ||
879 | c->rx_buf[0]=(void *)get_zeroed_page(GFP_KERNEL|GFP_DMA); | |
880 | if(c->rx_buf[0]==NULL) | |
881 | return -ENOBUFS; | |
882 | c->rx_buf[1]=c->rx_buf[0]+PAGE_SIZE/2; | |
883 | ||
884 | c->tx_dma_buf[0]=(void *)get_zeroed_page(GFP_KERNEL|GFP_DMA); | |
885 | if(c->tx_dma_buf[0]==NULL) | |
886 | { | |
887 | free_page((unsigned long)c->rx_buf[0]); | |
888 | c->rx_buf[0]=NULL; | |
889 | return -ENOBUFS; | |
890 | } | |
891 | c->tx_dma_buf[1]=c->tx_dma_buf[0]+PAGE_SIZE/2; | |
892 | ||
893 | c->tx_dma_used=0; | |
894 | c->dma_tx = 1; | |
895 | c->dma_num=0; | |
896 | c->dma_ready=1; | |
897 | ||
898 | /* | |
899 | * Enable DMA control mode | |
900 | */ | |
901 | ||
902 | spin_lock_irqsave(c->lock, cflags); | |
903 | ||
904 | /* | |
905 | * TX DMA via DIR/REQ | |
906 | */ | |
907 | ||
908 | c->regs[R14]|= DTRREQ; | |
909 | write_zsreg(c, R14, c->regs[R14]); | |
910 | ||
911 | c->regs[R1]&= ~TxINT_ENAB; | |
912 | write_zsreg(c, R1, c->regs[R1]); | |
913 | ||
914 | /* | |
915 | * RX DMA via W/Req | |
916 | */ | |
917 | ||
918 | c->regs[R1]|= WT_FN_RDYFN; | |
919 | c->regs[R1]|= WT_RDY_RT; | |
920 | c->regs[R1]|= INT_ERR_Rx; | |
921 | c->regs[R1]&= ~TxINT_ENAB; | |
922 | write_zsreg(c, R1, c->regs[R1]); | |
923 | c->regs[R1]|= WT_RDY_ENAB; | |
924 | write_zsreg(c, R1, c->regs[R1]); | |
925 | ||
926 | /* | |
927 | * DMA interrupts | |
928 | */ | |
929 | ||
930 | /* | |
931 | * Set up the DMA configuration | |
932 | */ | |
933 | ||
934 | dflags=claim_dma_lock(); | |
935 | ||
936 | disable_dma(c->rxdma); | |
937 | clear_dma_ff(c->rxdma); | |
938 | set_dma_mode(c->rxdma, DMA_MODE_READ|0x10); | |
939 | set_dma_addr(c->rxdma, virt_to_bus(c->rx_buf[0])); | |
940 | set_dma_count(c->rxdma, c->mtu); | |
941 | enable_dma(c->rxdma); | |
942 | ||
943 | disable_dma(c->txdma); | |
944 | clear_dma_ff(c->txdma); | |
945 | set_dma_mode(c->txdma, DMA_MODE_WRITE); | |
946 | disable_dma(c->txdma); | |
947 | ||
948 | release_dma_lock(dflags); | |
949 | ||
950 | /* | |
951 | * Select the DMA interrupt handlers | |
952 | */ | |
953 | ||
954 | c->rxdma_on = 1; | |
955 | c->txdma_on = 1; | |
956 | c->tx_dma_used = 1; | |
957 | ||
958 | c->irqs = &z8530_dma_sync; | |
959 | z8530_rtsdtr(c,1); | |
960 | write_zsreg(c, R3, c->regs[R3]|RxENABLE); | |
961 | ||
962 | spin_unlock_irqrestore(c->lock, cflags); | |
963 | ||
964 | return 0; | |
965 | } | |
966 | ||
967 | EXPORT_SYMBOL(z8530_sync_dma_open); | |
968 | ||
969 | /** | |
970 | * z8530_sync_dma_close - Close down DMA I/O | |
971 | * @dev: Network device to detach | |
972 | * @c: Z8530 channel to move into discard mode | |
973 | * | |
974 | * Shut down a DMA mode synchronous interface. Halt the DMA, and | |
975 | * free the buffers. | |
976 | */ | |
977 | ||
978 | int z8530_sync_dma_close(struct net_device *dev, struct z8530_channel *c) | |
979 | { | |
980 | u8 chk; | |
981 | unsigned long flags; | |
982 | ||
983 | c->irqs = &z8530_nop; | |
984 | c->max = 0; | |
985 | c->sync = 0; | |
986 | ||
987 | /* | |
988 | * Disable the PC DMA channels | |
989 | */ | |
990 | ||
991 | flags=claim_dma_lock(); | |
992 | disable_dma(c->rxdma); | |
993 | clear_dma_ff(c->rxdma); | |
994 | ||
995 | c->rxdma_on = 0; | |
996 | ||
997 | disable_dma(c->txdma); | |
998 | clear_dma_ff(c->txdma); | |
999 | release_dma_lock(flags); | |
1000 | ||
1001 | c->txdma_on = 0; | |
1002 | c->tx_dma_used = 0; | |
1003 | ||
1004 | spin_lock_irqsave(c->lock, flags); | |
1005 | ||
1006 | /* | |
1007 | * Disable DMA control mode | |
1008 | */ | |
1009 | ||
1010 | c->regs[R1]&= ~WT_RDY_ENAB; | |
1011 | write_zsreg(c, R1, c->regs[R1]); | |
1012 | c->regs[R1]&= ~(WT_RDY_RT|WT_FN_RDYFN|INT_ERR_Rx); | |
1013 | c->regs[R1]|= INT_ALL_Rx; | |
1014 | write_zsreg(c, R1, c->regs[R1]); | |
1015 | c->regs[R14]&= ~DTRREQ; | |
1016 | write_zsreg(c, R14, c->regs[R14]); | |
1017 | ||
1018 | if(c->rx_buf[0]) | |
1019 | { | |
1020 | free_page((unsigned long)c->rx_buf[0]); | |
1021 | c->rx_buf[0]=NULL; | |
1022 | } | |
1023 | if(c->tx_dma_buf[0]) | |
1024 | { | |
1025 | free_page((unsigned long)c->tx_dma_buf[0]); | |
1026 | c->tx_dma_buf[0]=NULL; | |
1027 | } | |
1028 | chk=read_zsreg(c,R0); | |
1029 | write_zsreg(c, R3, c->regs[R3]); | |
1030 | z8530_rtsdtr(c,0); | |
1031 | ||
1032 | spin_unlock_irqrestore(c->lock, flags); | |
1033 | ||
1034 | return 0; | |
1035 | } | |
1036 | ||
1037 | EXPORT_SYMBOL(z8530_sync_dma_close); | |
1038 | ||
1039 | /** | |
1040 | * z8530_sync_txdma_open - Open a Z8530 for TX driven DMA | |
1041 | * @dev: The network device to attach | |
1042 | * @c: The Z8530 channel to configure in sync DMA mode. | |
1043 | * | |
1044 | * Set up a Z85x30 device for synchronous DMA tranmission. One | |
1045 | * ISA DMA channel must be available for this to work. The receive | |
1046 | * side is run in PIO mode, but then it has the bigger FIFO. | |
1047 | */ | |
1048 | ||
1049 | int z8530_sync_txdma_open(struct net_device *dev, struct z8530_channel *c) | |
1050 | { | |
1051 | unsigned long cflags, dflags; | |
1052 | ||
1053 | printk("Opening sync interface for TX-DMA\n"); | |
1054 | c->sync = 1; | |
1055 | c->mtu = dev->mtu+64; | |
1056 | c->count = 0; | |
1057 | c->skb = NULL; | |
1058 | c->skb2 = NULL; | |
1059 | ||
1060 | /* | |
1061 | * Allocate the DMA flip buffers. Limit by page size. | |
1062 | * Everyone runs 1500 mtu or less on wan links so this | |
1063 | * should be fine. | |
1064 | */ | |
1065 | ||
1066 | if(c->mtu > PAGE_SIZE/2) | |
1067 | return -EMSGSIZE; | |
1068 | ||
1069 | c->tx_dma_buf[0]=(void *)get_zeroed_page(GFP_KERNEL|GFP_DMA); | |
1070 | if(c->tx_dma_buf[0]==NULL) | |
1071 | return -ENOBUFS; | |
1072 | ||
1073 | c->tx_dma_buf[1] = c->tx_dma_buf[0] + PAGE_SIZE/2; | |
1074 | ||
1075 | ||
1076 | spin_lock_irqsave(c->lock, cflags); | |
1077 | ||
1078 | /* | |
1079 | * Load the PIO receive ring | |
1080 | */ | |
1081 | ||
1082 | z8530_rx_done(c); | |
1083 | z8530_rx_done(c); | |
1084 | ||
1085 | /* | |
1086 | * Load the DMA interfaces up | |
1087 | */ | |
1088 | ||
1089 | c->rxdma_on = 0; | |
1090 | c->txdma_on = 0; | |
1091 | ||
1092 | c->tx_dma_used=0; | |
1093 | c->dma_num=0; | |
1094 | c->dma_ready=1; | |
1095 | c->dma_tx = 1; | |
1096 | ||
1097 | /* | |
1098 | * Enable DMA control mode | |
1099 | */ | |
1100 | ||
1101 | /* | |
1102 | * TX DMA via DIR/REQ | |
1103 | */ | |
1104 | c->regs[R14]|= DTRREQ; | |
1105 | write_zsreg(c, R14, c->regs[R14]); | |
1106 | ||
1107 | c->regs[R1]&= ~TxINT_ENAB; | |
1108 | write_zsreg(c, R1, c->regs[R1]); | |
1109 | ||
1110 | /* | |
1111 | * Set up the DMA configuration | |
1112 | */ | |
1113 | ||
1114 | dflags = claim_dma_lock(); | |
1115 | ||
1116 | disable_dma(c->txdma); | |
1117 | clear_dma_ff(c->txdma); | |
1118 | set_dma_mode(c->txdma, DMA_MODE_WRITE); | |
1119 | disable_dma(c->txdma); | |
1120 | ||
1121 | release_dma_lock(dflags); | |
1122 | ||
1123 | /* | |
1124 | * Select the DMA interrupt handlers | |
1125 | */ | |
1126 | ||
1127 | c->rxdma_on = 0; | |
1128 | c->txdma_on = 1; | |
1129 | c->tx_dma_used = 1; | |
1130 | ||
1131 | c->irqs = &z8530_txdma_sync; | |
1132 | z8530_rtsdtr(c,1); | |
1133 | write_zsreg(c, R3, c->regs[R3]|RxENABLE); | |
1134 | spin_unlock_irqrestore(c->lock, cflags); | |
1135 | ||
1136 | return 0; | |
1137 | } | |
1138 | ||
1139 | EXPORT_SYMBOL(z8530_sync_txdma_open); | |
1140 | ||
1141 | /** | |
1142 | * z8530_sync_txdma_close - Close down a TX driven DMA channel | |
1143 | * @dev: Network device to detach | |
1144 | * @c: Z8530 channel to move into discard mode | |
1145 | * | |
1146 | * Shut down a DMA/PIO split mode synchronous interface. Halt the DMA, | |
1147 | * and free the buffers. | |
1148 | */ | |
1149 | ||
1150 | int z8530_sync_txdma_close(struct net_device *dev, struct z8530_channel *c) | |
1151 | { | |
1152 | unsigned long dflags, cflags; | |
1153 | u8 chk; | |
1154 | ||
1155 | ||
1156 | spin_lock_irqsave(c->lock, cflags); | |
1157 | ||
1158 | c->irqs = &z8530_nop; | |
1159 | c->max = 0; | |
1160 | c->sync = 0; | |
1161 | ||
1162 | /* | |
1163 | * Disable the PC DMA channels | |
1164 | */ | |
1165 | ||
1166 | dflags = claim_dma_lock(); | |
1167 | ||
1168 | disable_dma(c->txdma); | |
1169 | clear_dma_ff(c->txdma); | |
1170 | c->txdma_on = 0; | |
1171 | c->tx_dma_used = 0; | |
1172 | ||
1173 | release_dma_lock(dflags); | |
1174 | ||
1175 | /* | |
1176 | * Disable DMA control mode | |
1177 | */ | |
1178 | ||
1179 | c->regs[R1]&= ~WT_RDY_ENAB; | |
1180 | write_zsreg(c, R1, c->regs[R1]); | |
1181 | c->regs[R1]&= ~(WT_RDY_RT|WT_FN_RDYFN|INT_ERR_Rx); | |
1182 | c->regs[R1]|= INT_ALL_Rx; | |
1183 | write_zsreg(c, R1, c->regs[R1]); | |
1184 | c->regs[R14]&= ~DTRREQ; | |
1185 | write_zsreg(c, R14, c->regs[R14]); | |
1186 | ||
1187 | if(c->tx_dma_buf[0]) | |
1188 | { | |
1189 | free_page((unsigned long)c->tx_dma_buf[0]); | |
1190 | c->tx_dma_buf[0]=NULL; | |
1191 | } | |
1192 | chk=read_zsreg(c,R0); | |
1193 | write_zsreg(c, R3, c->regs[R3]); | |
1194 | z8530_rtsdtr(c,0); | |
1195 | ||
1196 | spin_unlock_irqrestore(c->lock, cflags); | |
1197 | return 0; | |
1198 | } | |
1199 | ||
1200 | ||
1201 | EXPORT_SYMBOL(z8530_sync_txdma_close); | |
1202 | ||
1203 | ||
1204 | /* | |
1205 | * Name strings for Z8530 chips. SGI claim to have a 130, Zilog deny | |
1206 | * it exists... | |
1207 | */ | |
1208 | ||
1209 | static char *z8530_type_name[]={ | |
1210 | "Z8530", | |
1211 | "Z85C30", | |
1212 | "Z85230" | |
1213 | }; | |
1214 | ||
1215 | /** | |
1216 | * z8530_describe - Uniformly describe a Z8530 port | |
1217 | * @dev: Z8530 device to describe | |
1218 | * @mapping: string holding mapping type (eg "I/O" or "Mem") | |
1219 | * @io: the port value in question | |
1220 | * | |
1221 | * Describe a Z8530 in a standard format. We must pass the I/O as | |
1222 | * the port offset isnt predictable. The main reason for this function | |
1223 | * is to try and get a common format of report. | |
1224 | */ | |
1225 | ||
1226 | void z8530_describe(struct z8530_dev *dev, char *mapping, unsigned long io) | |
1227 | { | |
1228 | printk(KERN_INFO "%s: %s found at %s 0x%lX, IRQ %d.\n", | |
1229 | dev->name, | |
1230 | z8530_type_name[dev->type], | |
1231 | mapping, | |
1232 | Z8530_PORT_OF(io), | |
1233 | dev->irq); | |
1234 | } | |
1235 | ||
1236 | EXPORT_SYMBOL(z8530_describe); | |
1237 | ||
1238 | /* | |
1239 | * Locked operation part of the z8530 init code | |
1240 | */ | |
1241 | ||
1242 | static inline int do_z8530_init(struct z8530_dev *dev) | |
1243 | { | |
1244 | /* NOP the interrupt handlers first - we might get a | |
1245 | floating IRQ transition when we reset the chip */ | |
1246 | dev->chanA.irqs=&z8530_nop; | |
1247 | dev->chanB.irqs=&z8530_nop; | |
1248 | dev->chanA.dcdcheck=DCD; | |
1249 | dev->chanB.dcdcheck=DCD; | |
1250 | ||
1251 | /* Reset the chip */ | |
1252 | write_zsreg(&dev->chanA, R9, 0xC0); | |
1253 | udelay(200); | |
1254 | /* Now check its valid */ | |
1255 | write_zsreg(&dev->chanA, R12, 0xAA); | |
1256 | if(read_zsreg(&dev->chanA, R12)!=0xAA) | |
1257 | return -ENODEV; | |
1258 | write_zsreg(&dev->chanA, R12, 0x55); | |
1259 | if(read_zsreg(&dev->chanA, R12)!=0x55) | |
1260 | return -ENODEV; | |
1261 | ||
1262 | dev->type=Z8530; | |
1263 | ||
1264 | /* | |
1265 | * See the application note. | |
1266 | */ | |
1267 | ||
1268 | write_zsreg(&dev->chanA, R15, 0x01); | |
1269 | ||
1270 | /* | |
1271 | * If we can set the low bit of R15 then | |
1272 | * the chip is enhanced. | |
1273 | */ | |
1274 | ||
1275 | if(read_zsreg(&dev->chanA, R15)==0x01) | |
1276 | { | |
1277 | /* This C30 versus 230 detect is from Klaus Kudielka's dmascc */ | |
1278 | /* Put a char in the fifo */ | |
1279 | write_zsreg(&dev->chanA, R8, 0); | |
1280 | if(read_zsreg(&dev->chanA, R0)&Tx_BUF_EMP) | |
1281 | dev->type = Z85230; /* Has a FIFO */ | |
1282 | else | |
1283 | dev->type = Z85C30; /* Z85C30, 1 byte FIFO */ | |
1284 | } | |
1285 | ||
1286 | /* | |
1287 | * The code assumes R7' and friends are | |
1288 | * off. Use write_zsext() for these and keep | |
1289 | * this bit clear. | |
1290 | */ | |
1291 | ||
1292 | write_zsreg(&dev->chanA, R15, 0); | |
1293 | ||
1294 | /* | |
1295 | * At this point it looks like the chip is behaving | |
1296 | */ | |
1297 | ||
1298 | memcpy(dev->chanA.regs, reg_init, 16); | |
1299 | memcpy(dev->chanB.regs, reg_init ,16); | |
1300 | ||
1301 | return 0; | |
1302 | } | |
1303 | ||
1304 | /** | |
1305 | * z8530_init - Initialise a Z8530 device | |
1306 | * @dev: Z8530 device to initialise. | |
1307 | * | |
1308 | * Configure up a Z8530/Z85C30 or Z85230 chip. We check the device | |
1309 | * is present, identify the type and then program it to hopefully | |
1310 | * keep quite and behave. This matters a lot, a Z8530 in the wrong | |
1311 | * state will sometimes get into stupid modes generating 10Khz | |
1312 | * interrupt streams and the like. | |
1313 | * | |
1314 | * We set the interrupt handler up to discard any events, in case | |
1315 | * we get them during reset or setp. | |
1316 | * | |
1317 | * Return 0 for success, or a negative value indicating the problem | |
1318 | * in errno form. | |
1319 | */ | |
1320 | ||
1321 | int z8530_init(struct z8530_dev *dev) | |
1322 | { | |
1323 | unsigned long flags; | |
1324 | int ret; | |
1325 | ||
1326 | /* Set up the chip level lock */ | |
1327 | spin_lock_init(&dev->lock); | |
1328 | dev->chanA.lock = &dev->lock; | |
1329 | dev->chanB.lock = &dev->lock; | |
1330 | ||
1331 | spin_lock_irqsave(&dev->lock, flags); | |
1332 | ret = do_z8530_init(dev); | |
1333 | spin_unlock_irqrestore(&dev->lock, flags); | |
1334 | ||
1335 | return ret; | |
1336 | } | |
1337 | ||
1338 | ||
1339 | EXPORT_SYMBOL(z8530_init); | |
1340 | ||
1341 | /** | |
1342 | * z8530_shutdown - Shutdown a Z8530 device | |
1343 | * @dev: The Z8530 chip to shutdown | |
1344 | * | |
1345 | * We set the interrupt handlers to silence any interrupts. We then | |
1346 | * reset the chip and wait 100uS to be sure the reset completed. Just | |
1347 | * in case the caller then tries to do stuff. | |
1348 | * | |
1349 | * This is called without the lock held | |
1350 | */ | |
1351 | ||
1352 | int z8530_shutdown(struct z8530_dev *dev) | |
1353 | { | |
1354 | unsigned long flags; | |
1355 | /* Reset the chip */ | |
1356 | ||
1357 | spin_lock_irqsave(&dev->lock, flags); | |
1358 | dev->chanA.irqs=&z8530_nop; | |
1359 | dev->chanB.irqs=&z8530_nop; | |
1360 | write_zsreg(&dev->chanA, R9, 0xC0); | |
1361 | /* We must lock the udelay, the chip is offlimits here */ | |
1362 | udelay(100); | |
1363 | spin_unlock_irqrestore(&dev->lock, flags); | |
1364 | return 0; | |
1365 | } | |
1366 | ||
1367 | EXPORT_SYMBOL(z8530_shutdown); | |
1368 | ||
1369 | /** | |
1370 | * z8530_channel_load - Load channel data | |
1371 | * @c: Z8530 channel to configure | |
1372 | * @rtable: table of register, value pairs | |
1373 | * FIXME: ioctl to allow user uploaded tables | |
1374 | * | |
1375 | * Load a Z8530 channel up from the system data. We use +16 to | |
1376 | * indicate the "prime" registers. The value 255 terminates the | |
1377 | * table. | |
1378 | */ | |
1379 | ||
1380 | int z8530_channel_load(struct z8530_channel *c, u8 *rtable) | |
1381 | { | |
1382 | unsigned long flags; | |
1383 | ||
1384 | spin_lock_irqsave(c->lock, flags); | |
1385 | ||
1386 | while(*rtable!=255) | |
1387 | { | |
1388 | int reg=*rtable++; | |
1389 | if(reg>0x0F) | |
1390 | write_zsreg(c, R15, c->regs[15]|1); | |
1391 | write_zsreg(c, reg&0x0F, *rtable); | |
1392 | if(reg>0x0F) | |
1393 | write_zsreg(c, R15, c->regs[15]&~1); | |
1394 | c->regs[reg]=*rtable++; | |
1395 | } | |
1396 | c->rx_function=z8530_null_rx; | |
1397 | c->skb=NULL; | |
1398 | c->tx_skb=NULL; | |
1399 | c->tx_next_skb=NULL; | |
1400 | c->mtu=1500; | |
1401 | c->max=0; | |
1402 | c->count=0; | |
1403 | c->status=read_zsreg(c, R0); | |
1404 | c->sync=1; | |
1405 | write_zsreg(c, R3, c->regs[R3]|RxENABLE); | |
1406 | ||
1407 | spin_unlock_irqrestore(c->lock, flags); | |
1408 | return 0; | |
1409 | } | |
1410 | ||
1411 | EXPORT_SYMBOL(z8530_channel_load); | |
1412 | ||
1413 | ||
1414 | /** | |
1415 | * z8530_tx_begin - Begin packet transmission | |
1416 | * @c: The Z8530 channel to kick | |
1417 | * | |
1418 | * This is the speed sensitive side of transmission. If we are called | |
1419 | * and no buffer is being transmitted we commence the next buffer. If | |
1420 | * nothing is queued we idle the sync. | |
1421 | * | |
1422 | * Note: We are handling this code path in the interrupt path, keep it | |
1423 | * fast or bad things will happen. | |
1424 | * | |
1425 | * Called with the lock held. | |
1426 | */ | |
1427 | ||
1428 | static void z8530_tx_begin(struct z8530_channel *c) | |
1429 | { | |
1430 | unsigned long flags; | |
1431 | if(c->tx_skb) | |
1432 | return; | |
1433 | ||
1434 | c->tx_skb=c->tx_next_skb; | |
1435 | c->tx_next_skb=NULL; | |
1436 | c->tx_ptr=c->tx_next_ptr; | |
1437 | ||
1438 | if(c->tx_skb==NULL) | |
1439 | { | |
1440 | /* Idle on */ | |
1441 | if(c->dma_tx) | |
1442 | { | |
1443 | flags=claim_dma_lock(); | |
1444 | disable_dma(c->txdma); | |
1445 | /* | |
1446 | * Check if we crapped out. | |
1447 | */ | |
52e8a6a2 | 1448 | if (get_dma_residue(c->txdma)) |
1da177e4 | 1449 | { |
52e8a6a2 KH |
1450 | c->netdevice->stats.tx_dropped++; |
1451 | c->netdevice->stats.tx_fifo_errors++; | |
1da177e4 LT |
1452 | } |
1453 | release_dma_lock(flags); | |
1454 | } | |
1455 | c->txcount=0; | |
1456 | } | |
1457 | else | |
1458 | { | |
1459 | c->txcount=c->tx_skb->len; | |
1460 | ||
1461 | ||
1462 | if(c->dma_tx) | |
1463 | { | |
1464 | /* | |
1465 | * FIXME. DMA is broken for the original 8530, | |
1466 | * on the older parts we need to set a flag and | |
1467 | * wait for a further TX interrupt to fire this | |
1468 | * stage off | |
1469 | */ | |
1470 | ||
1471 | flags=claim_dma_lock(); | |
1472 | disable_dma(c->txdma); | |
1473 | ||
1474 | /* | |
1475 | * These two are needed by the 8530/85C30 | |
1476 | * and must be issued when idling. | |
1477 | */ | |
1478 | ||
1479 | if(c->dev->type!=Z85230) | |
1480 | { | |
1481 | write_zsctrl(c, RES_Tx_CRC); | |
1482 | write_zsctrl(c, RES_EOM_L); | |
1483 | } | |
1484 | write_zsreg(c, R10, c->regs[10]&~ABUNDER); | |
1485 | clear_dma_ff(c->txdma); | |
1486 | set_dma_addr(c->txdma, virt_to_bus(c->tx_ptr)); | |
1487 | set_dma_count(c->txdma, c->txcount); | |
1488 | enable_dma(c->txdma); | |
1489 | release_dma_lock(flags); | |
1490 | write_zsctrl(c, RES_EOM_L); | |
1491 | write_zsreg(c, R5, c->regs[R5]|TxENAB); | |
1492 | } | |
1493 | else | |
1494 | { | |
1495 | ||
1496 | /* ABUNDER off */ | |
1497 | write_zsreg(c, R10, c->regs[10]); | |
1498 | write_zsctrl(c, RES_Tx_CRC); | |
1499 | ||
1500 | while(c->txcount && (read_zsreg(c,R0)&Tx_BUF_EMP)) | |
1501 | { | |
1502 | write_zsreg(c, R8, *c->tx_ptr++); | |
1503 | c->txcount--; | |
1504 | } | |
1505 | ||
1506 | } | |
1507 | } | |
1508 | /* | |
1509 | * Since we emptied tx_skb we can ask for more | |
1510 | */ | |
1511 | netif_wake_queue(c->netdevice); | |
1512 | } | |
1513 | ||
1514 | /** | |
1515 | * z8530_tx_done - TX complete callback | |
1516 | * @c: The channel that completed a transmit. | |
1517 | * | |
1518 | * This is called when we complete a packet send. We wake the queue, | |
1519 | * start the next packet going and then free the buffer of the existing | |
1520 | * packet. This code is fairly timing sensitive. | |
1521 | * | |
1522 | * Called with the register lock held. | |
52e8a6a2 KH |
1523 | */ |
1524 | ||
1da177e4 LT |
1525 | static void z8530_tx_done(struct z8530_channel *c) |
1526 | { | |
1527 | struct sk_buff *skb; | |
1528 | ||
1529 | /* Actually this can happen.*/ | |
52e8a6a2 | 1530 | if (c->tx_skb == NULL) |
1da177e4 LT |
1531 | return; |
1532 | ||
52e8a6a2 KH |
1533 | skb = c->tx_skb; |
1534 | c->tx_skb = NULL; | |
1da177e4 | 1535 | z8530_tx_begin(c); |
52e8a6a2 KH |
1536 | c->netdevice->stats.tx_packets++; |
1537 | c->netdevice->stats.tx_bytes += skb->len; | |
1da177e4 LT |
1538 | dev_kfree_skb_irq(skb); |
1539 | } | |
1540 | ||
1541 | /** | |
1542 | * z8530_null_rx - Discard a packet | |
1543 | * @c: The channel the packet arrived on | |
1544 | * @skb: The buffer | |
1545 | * | |
1546 | * We point the receive handler at this function when idle. Instead | |
52e8a6a2 | 1547 | * of processing the frames we get to throw them away. |
1da177e4 LT |
1548 | */ |
1549 | ||
1550 | void z8530_null_rx(struct z8530_channel *c, struct sk_buff *skb) | |
1551 | { | |
1552 | dev_kfree_skb_any(skb); | |
1553 | } | |
1554 | ||
1555 | EXPORT_SYMBOL(z8530_null_rx); | |
1556 | ||
1557 | /** | |
1558 | * z8530_rx_done - Receive completion callback | |
1559 | * @c: The channel that completed a receive | |
1560 | * | |
1561 | * A new packet is complete. Our goal here is to get back into receive | |
1562 | * mode as fast as possible. On the Z85230 we could change to using | |
1563 | * ESCC mode, but on the older chips we have no choice. We flip to the | |
1564 | * new buffer immediately in DMA mode so that the DMA of the next | |
1565 | * frame can occur while we are copying the previous buffer to an sk_buff | |
1566 | * | |
1567 | * Called with the lock held | |
1568 | */ | |
1569 | ||
1570 | static void z8530_rx_done(struct z8530_channel *c) | |
1571 | { | |
1572 | struct sk_buff *skb; | |
1573 | int ct; | |
1574 | ||
1575 | /* | |
1576 | * Is our receive engine in DMA mode | |
1577 | */ | |
1578 | ||
1579 | if(c->rxdma_on) | |
1580 | { | |
1581 | /* | |
1582 | * Save the ready state and the buffer currently | |
1583 | * being used as the DMA target | |
1584 | */ | |
1585 | ||
1586 | int ready=c->dma_ready; | |
1587 | unsigned char *rxb=c->rx_buf[c->dma_num]; | |
1588 | unsigned long flags; | |
1589 | ||
1590 | /* | |
1591 | * Complete this DMA. Neccessary to find the length | |
1592 | */ | |
1593 | ||
1594 | flags=claim_dma_lock(); | |
1595 | ||
1596 | disable_dma(c->rxdma); | |
1597 | clear_dma_ff(c->rxdma); | |
1598 | c->rxdma_on=0; | |
1599 | ct=c->mtu-get_dma_residue(c->rxdma); | |
1600 | if(ct<0) | |
1601 | ct=2; /* Shit happens.. */ | |
1602 | c->dma_ready=0; | |
1603 | ||
1604 | /* | |
1605 | * Normal case: the other slot is free, start the next DMA | |
1606 | * into it immediately. | |
1607 | */ | |
1608 | ||
1609 | if(ready) | |
1610 | { | |
1611 | c->dma_num^=1; | |
1612 | set_dma_mode(c->rxdma, DMA_MODE_READ|0x10); | |
1613 | set_dma_addr(c->rxdma, virt_to_bus(c->rx_buf[c->dma_num])); | |
1614 | set_dma_count(c->rxdma, c->mtu); | |
1615 | c->rxdma_on = 1; | |
1616 | enable_dma(c->rxdma); | |
1617 | /* Stop any frames that we missed the head of | |
1618 | from passing */ | |
1619 | write_zsreg(c, R0, RES_Rx_CRC); | |
1620 | } | |
1621 | else | |
1622 | /* Can't occur as we dont reenable the DMA irq until | |
1623 | after the flip is done */ | |
52e8a6a2 KH |
1624 | printk(KERN_WARNING "%s: DMA flip overrun!\n", |
1625 | c->netdevice->name); | |
1626 | ||
1da177e4 | 1627 | release_dma_lock(flags); |
52e8a6a2 | 1628 | |
1da177e4 LT |
1629 | /* |
1630 | * Shove the old buffer into an sk_buff. We can't DMA | |
1631 | * directly into one on a PC - it might be above the 16Mb | |
1632 | * boundary. Optimisation - we could check to see if we | |
1633 | * can avoid the copy. Optimisation 2 - make the memcpy | |
1634 | * a copychecksum. | |
1635 | */ | |
52e8a6a2 KH |
1636 | |
1637 | skb = dev_alloc_skb(ct); | |
1638 | if (skb == NULL) { | |
1639 | c->netdevice->stats.rx_dropped++; | |
1640 | printk(KERN_WARNING "%s: Memory squeeze.\n", | |
1641 | c->netdevice->name); | |
1642 | } else { | |
1da177e4 | 1643 | skb_put(skb, ct); |
27d7ff46 | 1644 | skb_copy_to_linear_data(skb, rxb, ct); |
52e8a6a2 KH |
1645 | c->netdevice->stats.rx_packets++; |
1646 | c->netdevice->stats.rx_bytes += ct; | |
1da177e4 | 1647 | } |
52e8a6a2 KH |
1648 | c->dma_ready = 1; |
1649 | } else { | |
1650 | RT_LOCK; | |
1651 | skb = c->skb; | |
1652 | ||
1da177e4 LT |
1653 | /* |
1654 | * The game we play for non DMA is similar. We want to | |
1655 | * get the controller set up for the next packet as fast | |
1656 | * as possible. We potentially only have one byte + the | |
1657 | * fifo length for this. Thus we want to flip to the new | |
1658 | * buffer and then mess around copying and allocating | |
1659 | * things. For the current case it doesn't matter but | |
1660 | * if you build a system where the sync irq isnt blocked | |
1661 | * by the kernel IRQ disable then you need only block the | |
1662 | * sync IRQ for the RT_LOCK area. | |
52e8a6a2 | 1663 | * |
1da177e4 LT |
1664 | */ |
1665 | ct=c->count; | |
52e8a6a2 | 1666 | |
1da177e4 LT |
1667 | c->skb = c->skb2; |
1668 | c->count = 0; | |
1669 | c->max = c->mtu; | |
52e8a6a2 | 1670 | if (c->skb) { |
1da177e4 LT |
1671 | c->dptr = c->skb->data; |
1672 | c->max = c->mtu; | |
52e8a6a2 KH |
1673 | } else { |
1674 | c->count = 0; | |
1da177e4 LT |
1675 | c->max = 0; |
1676 | } | |
1677 | RT_UNLOCK; | |
1678 | ||
1679 | c->skb2 = dev_alloc_skb(c->mtu); | |
52e8a6a2 | 1680 | if (c->skb2 == NULL) |
1da177e4 | 1681 | printk(KERN_WARNING "%s: memory squeeze.\n", |
52e8a6a2 | 1682 | c->netdevice->name); |
1da177e4 | 1683 | else |
52e8a6a2 KH |
1684 | skb_put(c->skb2, c->mtu); |
1685 | c->netdevice->stats.rx_packets++; | |
1686 | c->netdevice->stats.rx_bytes += ct; | |
1da177e4 LT |
1687 | } |
1688 | /* | |
1689 | * If we received a frame we must now process it. | |
1690 | */ | |
52e8a6a2 | 1691 | if (skb) { |
1da177e4 | 1692 | skb_trim(skb, ct); |
52e8a6a2 KH |
1693 | c->rx_function(c, skb); |
1694 | } else { | |
1695 | c->netdevice->stats.rx_dropped++; | |
1da177e4 LT |
1696 | printk(KERN_ERR "%s: Lost a frame\n", c->netdevice->name); |
1697 | } | |
1698 | } | |
1699 | ||
1700 | /** | |
1701 | * spans_boundary - Check a packet can be ISA DMA'd | |
1702 | * @skb: The buffer to check | |
1703 | * | |
1704 | * Returns true if the buffer cross a DMA boundary on a PC. The poor | |
1705 | * thing can only DMA within a 64K block not across the edges of it. | |
1706 | */ | |
52e8a6a2 | 1707 | |
1da177e4 LT |
1708 | static inline int spans_boundary(struct sk_buff *skb) |
1709 | { | |
1710 | unsigned long a=(unsigned long)skb->data; | |
1711 | a^=(a+skb->len); | |
1712 | if(a&0x00010000) /* If the 64K bit is different.. */ | |
1713 | return 1; | |
1714 | return 0; | |
1715 | } | |
1716 | ||
1717 | /** | |
1718 | * z8530_queue_xmit - Queue a packet | |
1719 | * @c: The channel to use | |
1720 | * @skb: The packet to kick down the channel | |
1721 | * | |
1722 | * Queue a packet for transmission. Because we have rather | |
1723 | * hard to hit interrupt latencies for the Z85230 per packet | |
1724 | * even in DMA mode we do the flip to DMA buffer if needed here | |
1725 | * not in the IRQ. | |
1726 | * | |
1727 | * Called from the network code. The lock is not held at this | |
1728 | * point. | |
1729 | */ | |
1730 | ||
d71a6749 | 1731 | netdev_tx_t z8530_queue_xmit(struct z8530_channel *c, struct sk_buff *skb) |
1da177e4 LT |
1732 | { |
1733 | unsigned long flags; | |
1734 | ||
1735 | netif_stop_queue(c->netdevice); | |
1736 | if(c->tx_next_skb) | |
d71a6749 SH |
1737 | return NETDEV_TX_BUSY; |
1738 | ||
1da177e4 LT |
1739 | |
1740 | /* PC SPECIFIC - DMA limits */ | |
1741 | ||
1742 | /* | |
1743 | * If we will DMA the transmit and its gone over the ISA bus | |
1744 | * limit, then copy to the flip buffer | |
1745 | */ | |
1746 | ||
1747 | if(c->dma_tx && ((unsigned long)(virt_to_bus(skb->data+skb->len))>=16*1024*1024 || spans_boundary(skb))) | |
1748 | { | |
1749 | /* | |
1750 | * Send the flip buffer, and flip the flippy bit. | |
1751 | * We don't care which is used when just so long as | |
1752 | * we never use the same buffer twice in a row. Since | |
1753 | * only one buffer can be going out at a time the other | |
1754 | * has to be safe. | |
1755 | */ | |
1756 | c->tx_next_ptr=c->tx_dma_buf[c->tx_dma_used]; | |
1757 | c->tx_dma_used^=1; /* Flip temp buffer */ | |
d626f62b | 1758 | skb_copy_from_linear_data(skb, c->tx_next_ptr, skb->len); |
1da177e4 LT |
1759 | } |
1760 | else | |
1761 | c->tx_next_ptr=skb->data; | |
1762 | RT_LOCK; | |
1763 | c->tx_next_skb=skb; | |
1764 | RT_UNLOCK; | |
1765 | ||
1766 | spin_lock_irqsave(c->lock, flags); | |
1767 | z8530_tx_begin(c); | |
1768 | spin_unlock_irqrestore(c->lock, flags); | |
1769 | ||
d71a6749 | 1770 | return NETDEV_TX_OK; |
1da177e4 LT |
1771 | } |
1772 | ||
1773 | EXPORT_SYMBOL(z8530_queue_xmit); | |
1774 | ||
1da177e4 LT |
1775 | /* |
1776 | * Module support | |
1777 | */ | |
5ee0d593 HE |
1778 | static const char banner[] __initdata = |
1779 | KERN_INFO "Generic Z85C30/Z85230 interface driver v0.02\n"; | |
1da177e4 LT |
1780 | |
1781 | static int __init z85230_init_driver(void) | |
1782 | { | |
1783 | printk(banner); | |
1784 | return 0; | |
1785 | } | |
1786 | module_init(z85230_init_driver); | |
1787 | ||
1788 | static void __exit z85230_cleanup_driver(void) | |
1789 | { | |
1790 | } | |
1791 | module_exit(z85230_cleanup_driver); | |
1792 | ||
1793 | MODULE_AUTHOR("Red Hat Inc."); | |
1794 | MODULE_DESCRIPTION("Z85x30 synchronous driver core"); | |
1795 | MODULE_LICENSE("GPL"); |