]>
Commit | Line | Data |
---|---|---|
1da177e4 LT |
1 | /* drivers/serial/serial_lh7a40x.c |
2 | * | |
3 | * Copyright (C) 2004 Coastal Environmental Systems | |
4 | * | |
5 | * This program is free software; you can redistribute it and/or | |
6 | * modify it under the terms of the GNU General Public License | |
7 | * version 2 as published by the Free Software Foundation. | |
8 | * | |
9 | */ | |
10 | ||
11 | /* Driver for Sharp LH7A40X embedded serial ports | |
12 | * | |
13 | * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o. | |
14 | * Based on drivers/serial/amba.c, by Deep Blue Solutions Ltd. | |
15 | * | |
16 | * --- | |
17 | * | |
18 | * This driver supports the embedded UARTs of the Sharp LH7A40X series | |
19 | * CPUs. While similar to the 16550 and other UART chips, there is | |
20 | * nothing close to register compatibility. Moreover, some of the | |
21 | * modem control lines are not available, either in the chip or they | |
22 | * are lacking in the board-level implementation. | |
23 | * | |
24 | * - Use of SIRDIS | |
25 | * For simplicity, we disable the IR functions of any UART whenever | |
26 | * we enable it. | |
27 | * | |
28 | */ | |
29 | ||
30 | #include <linux/config.h> | |
31 | ||
32 | #if defined(CONFIG_SERIAL_LH7A40X_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) | |
33 | #define SUPPORT_SYSRQ | |
34 | #endif | |
35 | ||
36 | #include <linux/module.h> | |
37 | #include <linux/ioport.h> | |
38 | #include <linux/init.h> | |
39 | #include <linux/console.h> | |
40 | #include <linux/sysrq.h> | |
41 | #include <linux/tty.h> | |
42 | #include <linux/tty_flip.h> | |
43 | #include <linux/serial_core.h> | |
44 | #include <linux/serial.h> | |
45 | ||
46 | #include <asm/io.h> | |
47 | #include <asm/irq.h> | |
48 | ||
49 | #define DEV_MAJOR 204 | |
50 | #define DEV_MINOR 16 | |
51 | #define DEV_NR 3 | |
52 | ||
53 | #define ISR_LOOP_LIMIT 256 | |
54 | ||
55 | #define UR(p,o) _UR ((p)->membase, o) | |
56 | #define _UR(b,o) (*((volatile unsigned int*)(((unsigned char*) b) + (o)))) | |
57 | #define BIT_CLR(p,o,m) UR(p,o) = UR(p,o) & (~(unsigned int)m) | |
58 | #define BIT_SET(p,o,m) UR(p,o) = UR(p,o) | ( (unsigned int)m) | |
59 | ||
60 | #define UART_REG_SIZE 32 | |
61 | ||
62 | #define UART_R_DATA (0x00) | |
63 | #define UART_R_FCON (0x04) | |
64 | #define UART_R_BRCON (0x08) | |
65 | #define UART_R_CON (0x0c) | |
66 | #define UART_R_STATUS (0x10) | |
67 | #define UART_R_RAWISR (0x14) | |
68 | #define UART_R_INTEN (0x18) | |
69 | #define UART_R_ISR (0x1c) | |
70 | ||
71 | #define UARTEN (0x01) /* UART enable */ | |
72 | #define SIRDIS (0x02) /* Serial IR disable (UART1 only) */ | |
73 | ||
74 | #define RxEmpty (0x10) | |
75 | #define TxEmpty (0x80) | |
76 | #define TxFull (0x20) | |
77 | #define nRxRdy RxEmpty | |
78 | #define nTxRdy TxFull | |
79 | #define TxBusy (0x08) | |
80 | ||
81 | #define RxBreak (0x0800) | |
82 | #define RxOverrunError (0x0400) | |
83 | #define RxParityError (0x0200) | |
84 | #define RxFramingError (0x0100) | |
85 | #define RxError (RxBreak | RxOverrunError | RxParityError | RxFramingError) | |
86 | ||
87 | #define DCD (0x04) | |
88 | #define DSR (0x02) | |
89 | #define CTS (0x01) | |
90 | ||
91 | #define RxInt (0x01) | |
92 | #define TxInt (0x02) | |
93 | #define ModemInt (0x04) | |
94 | #define RxTimeoutInt (0x08) | |
95 | ||
96 | #define MSEOI (0x10) | |
97 | ||
98 | #define WLEN_8 (0x60) | |
99 | #define WLEN_7 (0x40) | |
100 | #define WLEN_6 (0x20) | |
101 | #define WLEN_5 (0x00) | |
102 | #define WLEN (0x60) /* Mask for all word-length bits */ | |
103 | #define STP2 (0x08) | |
104 | #define PEN (0x02) /* Parity Enable */ | |
105 | #define EPS (0x04) /* Even Parity Set */ | |
106 | #define FEN (0x10) /* FIFO Enable */ | |
107 | #define BRK (0x01) /* Send Break */ | |
108 | ||
109 | ||
110 | struct uart_port_lh7a40x { | |
111 | struct uart_port port; | |
112 | unsigned int statusPrev; /* Most recently read modem status */ | |
113 | }; | |
114 | ||
b129a8cc | 115 | static void lh7a40xuart_stop_tx (struct uart_port* port) |
1da177e4 LT |
116 | { |
117 | BIT_CLR (port, UART_R_INTEN, TxInt); | |
118 | } | |
119 | ||
b129a8cc | 120 | static void lh7a40xuart_start_tx (struct uart_port* port) |
1da177e4 LT |
121 | { |
122 | BIT_SET (port, UART_R_INTEN, TxInt); | |
123 | ||
124 | /* *** FIXME: do I need to check for startup of the | |
125 | transmitter? The old driver did, but AMBA | |
126 | doesn't . */ | |
127 | } | |
128 | ||
129 | static void lh7a40xuart_stop_rx (struct uart_port* port) | |
130 | { | |
131 | BIT_SET (port, UART_R_INTEN, RxTimeoutInt | RxInt); | |
132 | } | |
133 | ||
134 | static void lh7a40xuart_enable_ms (struct uart_port* port) | |
135 | { | |
136 | BIT_SET (port, UART_R_INTEN, ModemInt); | |
137 | } | |
138 | ||
139 | static void | |
140 | #ifdef SUPPORT_SYSRQ | |
141 | lh7a40xuart_rx_chars (struct uart_port* port, struct pt_regs* regs) | |
142 | #else | |
143 | lh7a40xuart_rx_chars (struct uart_port* port) | |
144 | #endif | |
145 | { | |
146 | struct tty_struct* tty = port->info->tty; | |
147 | int cbRxMax = 256; /* (Gross) limit on receive */ | |
148 | unsigned int data, flag;/* Received data and status */ | |
149 | ||
150 | while (!(UR (port, UART_R_STATUS) & nRxRdy) && --cbRxMax) { | |
1da177e4 LT |
151 | data = UR (port, UART_R_DATA); |
152 | flag = TTY_NORMAL; | |
153 | ++port->icount.rx; | |
154 | ||
45849282 | 155 | if (unlikely(data & RxError)) { /* Quick check, short-circuit */ |
1da177e4 LT |
156 | if (data & RxBreak) { |
157 | data &= ~(RxFramingError | RxParityError); | |
158 | ++port->icount.brk; | |
159 | if (uart_handle_break (port)) | |
160 | continue; | |
161 | } | |
162 | else if (data & RxParityError) | |
163 | ++port->icount.parity; | |
164 | else if (data & RxFramingError) | |
165 | ++port->icount.frame; | |
166 | if (data & RxOverrunError) | |
167 | ++port->icount.overrun; | |
168 | ||
169 | /* Mask by termios, leave Rx'd byte */ | |
170 | data &= port->read_status_mask | 0xff; | |
171 | ||
172 | if (data & RxBreak) | |
173 | flag = TTY_BREAK; | |
174 | else if (data & RxParityError) | |
175 | flag = TTY_PARITY; | |
176 | else if (data & RxFramingError) | |
177 | flag = TTY_FRAME; | |
178 | } | |
179 | ||
180 | if (uart_handle_sysrq_char (port, (unsigned char) data, regs)) | |
181 | continue; | |
182 | ||
05ab3014 | 183 | uart_insert_char(port, data, RxOverrunError, data, flag); |
1da177e4 LT |
184 | } |
185 | tty_flip_buffer_push (tty); | |
186 | return; | |
187 | } | |
188 | ||
189 | static void lh7a40xuart_tx_chars (struct uart_port* port) | |
190 | { | |
191 | struct circ_buf* xmit = &port->info->xmit; | |
192 | int cbTxMax = port->fifosize; | |
193 | ||
194 | if (port->x_char) { | |
195 | UR (port, UART_R_DATA) = port->x_char; | |
196 | ++port->icount.tx; | |
197 | port->x_char = 0; | |
198 | return; | |
199 | } | |
200 | if (uart_circ_empty (xmit) || uart_tx_stopped (port)) { | |
1cd9855c | 201 | lh7a40xuart_stop_tx (port); |
1da177e4 LT |
202 | return; |
203 | } | |
204 | ||
205 | /* Unlike the AMBA UART, the lh7a40x UART does not guarantee | |
206 | that at least half of the FIFO is empty. Instead, we check | |
207 | status for every character. Using the AMBA method causes | |
208 | the transmitter to drop characters. */ | |
209 | ||
210 | do { | |
211 | UR (port, UART_R_DATA) = xmit->buf[xmit->tail]; | |
212 | xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); | |
213 | ++port->icount.tx; | |
214 | if (uart_circ_empty(xmit)) | |
215 | break; | |
216 | } while (!(UR (port, UART_R_STATUS) & nTxRdy) | |
217 | && cbTxMax--); | |
218 | ||
219 | if (uart_circ_chars_pending (xmit) < WAKEUP_CHARS) | |
220 | uart_write_wakeup (port); | |
221 | ||
222 | if (uart_circ_empty (xmit)) | |
1cd9855c | 223 | lh7a40xuart_stop_tx (port); |
1da177e4 LT |
224 | } |
225 | ||
226 | static void lh7a40xuart_modem_status (struct uart_port* port) | |
227 | { | |
228 | unsigned int status = UR (port, UART_R_STATUS); | |
229 | unsigned int delta | |
230 | = status ^ ((struct uart_port_lh7a40x*) port)->statusPrev; | |
231 | ||
232 | BIT_SET (port, UART_R_RAWISR, MSEOI); /* Clear modem status intr */ | |
233 | ||
234 | if (!delta) /* Only happens if we missed 2 transitions */ | |
235 | return; | |
236 | ||
237 | ((struct uart_port_lh7a40x*) port)->statusPrev = status; | |
238 | ||
239 | if (delta & DCD) | |
240 | uart_handle_dcd_change (port, status & DCD); | |
241 | ||
242 | if (delta & DSR) | |
243 | ++port->icount.dsr; | |
244 | ||
245 | if (delta & CTS) | |
246 | uart_handle_cts_change (port, status & CTS); | |
247 | ||
248 | wake_up_interruptible (&port->info->delta_msr_wait); | |
249 | } | |
250 | ||
251 | static irqreturn_t lh7a40xuart_int (int irq, void* dev_id, | |
252 | struct pt_regs* regs) | |
253 | { | |
254 | struct uart_port* port = dev_id; | |
255 | unsigned int cLoopLimit = ISR_LOOP_LIMIT; | |
256 | unsigned int isr = UR (port, UART_R_ISR); | |
257 | ||
258 | ||
259 | do { | |
260 | if (isr & (RxInt | RxTimeoutInt)) | |
261 | #ifdef SUPPORT_SYSRQ | |
262 | lh7a40xuart_rx_chars(port, regs); | |
263 | #else | |
264 | lh7a40xuart_rx_chars(port); | |
265 | #endif | |
266 | if (isr & ModemInt) | |
267 | lh7a40xuart_modem_status (port); | |
268 | if (isr & TxInt) | |
269 | lh7a40xuart_tx_chars (port); | |
270 | ||
271 | if (--cLoopLimit == 0) | |
272 | break; | |
273 | ||
274 | isr = UR (port, UART_R_ISR); | |
275 | } while (isr & (RxInt | TxInt | RxTimeoutInt)); | |
276 | ||
277 | return IRQ_HANDLED; | |
278 | } | |
279 | ||
280 | static unsigned int lh7a40xuart_tx_empty (struct uart_port* port) | |
281 | { | |
282 | return (UR (port, UART_R_STATUS) & TxEmpty) ? TIOCSER_TEMT : 0; | |
283 | } | |
284 | ||
285 | static unsigned int lh7a40xuart_get_mctrl (struct uart_port* port) | |
286 | { | |
287 | unsigned int result = 0; | |
288 | unsigned int status = UR (port, UART_R_STATUS); | |
289 | ||
290 | if (status & DCD) | |
291 | result |= TIOCM_CAR; | |
292 | if (status & DSR) | |
293 | result |= TIOCM_DSR; | |
294 | if (status & CTS) | |
295 | result |= TIOCM_CTS; | |
296 | ||
297 | return result; | |
298 | } | |
299 | ||
300 | static void lh7a40xuart_set_mctrl (struct uart_port* port, unsigned int mctrl) | |
301 | { | |
302 | /* None of the ports supports DTR. UART1 supports RTS through GPIO. */ | |
303 | /* Note, kernel appears to be setting DTR and RTS on console. */ | |
304 | ||
305 | /* *** FIXME: this deserves more work. There's some work in | |
306 | tracing all of the IO pins. */ | |
307 | #if 0 | |
308 | if( port->mapbase == UART1_PHYS) { | |
309 | gpioRegs_t *gpio = (gpioRegs_t *)IO_ADDRESS(GPIO_PHYS); | |
310 | ||
311 | if (mctrl & TIOCM_RTS) | |
312 | gpio->pbdr &= ~GPIOB_UART1_RTS; | |
313 | else | |
314 | gpio->pbdr |= GPIOB_UART1_RTS; | |
315 | } | |
316 | #endif | |
317 | } | |
318 | ||
319 | static void lh7a40xuart_break_ctl (struct uart_port* port, int break_state) | |
320 | { | |
321 | unsigned long flags; | |
322 | ||
323 | spin_lock_irqsave(&port->lock, flags); | |
324 | if (break_state == -1) | |
325 | BIT_SET (port, UART_R_FCON, BRK); /* Assert break */ | |
326 | else | |
327 | BIT_CLR (port, UART_R_FCON, BRK); /* Deassert break */ | |
328 | spin_unlock_irqrestore(&port->lock, flags); | |
329 | } | |
330 | ||
331 | static int lh7a40xuart_startup (struct uart_port* port) | |
332 | { | |
333 | int retval; | |
334 | ||
335 | retval = request_irq (port->irq, lh7a40xuart_int, 0, | |
336 | "serial_lh7a40x", port); | |
337 | if (retval) | |
338 | return retval; | |
339 | ||
340 | /* Initial modem control-line settings */ | |
341 | ((struct uart_port_lh7a40x*) port)->statusPrev | |
342 | = UR (port, UART_R_STATUS); | |
343 | ||
344 | /* There is presently no configuration option to enable IR. | |
345 | Thus, we always disable it. */ | |
346 | ||
347 | BIT_SET (port, UART_R_CON, UARTEN | SIRDIS); | |
348 | BIT_SET (port, UART_R_INTEN, RxTimeoutInt | RxInt); | |
349 | ||
350 | return 0; | |
351 | } | |
352 | ||
353 | static void lh7a40xuart_shutdown (struct uart_port* port) | |
354 | { | |
355 | free_irq (port->irq, port); | |
356 | BIT_CLR (port, UART_R_FCON, BRK | FEN); | |
357 | BIT_CLR (port, UART_R_CON, UARTEN); | |
358 | } | |
359 | ||
360 | static void lh7a40xuart_set_termios (struct uart_port* port, | |
361 | struct termios* termios, | |
362 | struct termios* old) | |
363 | { | |
364 | unsigned int con; | |
365 | unsigned int inten; | |
366 | unsigned int fcon; | |
367 | unsigned long flags; | |
368 | unsigned int baud; | |
369 | unsigned int quot; | |
370 | ||
371 | baud = uart_get_baud_rate (port, termios, old, 8, port->uartclk/16); | |
372 | quot = uart_get_divisor (port, baud); /* -1 performed elsewhere */ | |
373 | ||
374 | switch (termios->c_cflag & CSIZE) { | |
375 | case CS5: | |
376 | fcon = WLEN_5; | |
377 | break; | |
378 | case CS6: | |
379 | fcon = WLEN_6; | |
380 | break; | |
381 | case CS7: | |
382 | fcon = WLEN_7; | |
383 | break; | |
384 | case CS8: | |
385 | default: | |
386 | fcon = WLEN_8; | |
387 | break; | |
388 | } | |
389 | if (termios->c_cflag & CSTOPB) | |
390 | fcon |= STP2; | |
391 | if (termios->c_cflag & PARENB) { | |
392 | fcon |= PEN; | |
393 | if (!(termios->c_cflag & PARODD)) | |
394 | fcon |= EPS; | |
395 | } | |
396 | if (port->fifosize > 1) | |
397 | fcon |= FEN; | |
398 | ||
399 | spin_lock_irqsave (&port->lock, flags); | |
400 | ||
401 | uart_update_timeout (port, termios->c_cflag, baud); | |
402 | ||
403 | port->read_status_mask = RxOverrunError; | |
404 | if (termios->c_iflag & INPCK) | |
405 | port->read_status_mask |= RxFramingError | RxParityError; | |
406 | if (termios->c_iflag & (BRKINT | PARMRK)) | |
407 | port->read_status_mask |= RxBreak; | |
408 | ||
409 | /* Figure mask for status we ignore */ | |
410 | port->ignore_status_mask = 0; | |
411 | if (termios->c_iflag & IGNPAR) | |
412 | port->ignore_status_mask |= RxFramingError | RxParityError; | |
413 | if (termios->c_iflag & IGNBRK) { | |
414 | port->ignore_status_mask |= RxBreak; | |
415 | /* Ignore overrun when ignorning parity */ | |
416 | /* *** FIXME: is this in the right place? */ | |
417 | if (termios->c_iflag & IGNPAR) | |
418 | port->ignore_status_mask |= RxOverrunError; | |
419 | } | |
420 | ||
421 | /* Ignore all receive errors when receive disabled */ | |
422 | if ((termios->c_cflag & CREAD) == 0) | |
423 | port->ignore_status_mask |= RxError; | |
424 | ||
425 | con = UR (port, UART_R_CON); | |
426 | inten = (UR (port, UART_R_INTEN) & ~ModemInt); | |
427 | ||
428 | if (UART_ENABLE_MS (port, termios->c_cflag)) | |
429 | inten |= ModemInt; | |
430 | ||
431 | BIT_CLR (port, UART_R_CON, UARTEN); /* Disable UART */ | |
432 | UR (port, UART_R_INTEN) = 0; /* Disable interrupts */ | |
433 | UR (port, UART_R_BRCON) = quot - 1; /* Set baud rate divisor */ | |
434 | UR (port, UART_R_FCON) = fcon; /* Set FIFO and frame ctrl */ | |
435 | UR (port, UART_R_INTEN) = inten; /* Enable interrupts */ | |
436 | UR (port, UART_R_CON) = con; /* Restore UART mode */ | |
437 | ||
438 | spin_unlock_irqrestore(&port->lock, flags); | |
439 | } | |
440 | ||
441 | static const char* lh7a40xuart_type (struct uart_port* port) | |
442 | { | |
443 | return port->type == PORT_LH7A40X ? "LH7A40X" : NULL; | |
444 | } | |
445 | ||
446 | static void lh7a40xuart_release_port (struct uart_port* port) | |
447 | { | |
448 | release_mem_region (port->mapbase, UART_REG_SIZE); | |
449 | } | |
450 | ||
451 | static int lh7a40xuart_request_port (struct uart_port* port) | |
452 | { | |
453 | return request_mem_region (port->mapbase, UART_REG_SIZE, | |
454 | "serial_lh7a40x") != NULL | |
455 | ? 0 : -EBUSY; | |
456 | } | |
457 | ||
458 | static void lh7a40xuart_config_port (struct uart_port* port, int flags) | |
459 | { | |
460 | if (flags & UART_CONFIG_TYPE) { | |
461 | port->type = PORT_LH7A40X; | |
462 | lh7a40xuart_request_port (port); | |
463 | } | |
464 | } | |
465 | ||
466 | static int lh7a40xuart_verify_port (struct uart_port* port, | |
467 | struct serial_struct* ser) | |
468 | { | |
469 | int ret = 0; | |
470 | ||
471 | if (ser->type != PORT_UNKNOWN && ser->type != PORT_LH7A40X) | |
472 | ret = -EINVAL; | |
473 | if (ser->irq < 0 || ser->irq >= NR_IRQS) | |
474 | ret = -EINVAL; | |
475 | if (ser->baud_base < 9600) /* *** FIXME: is this true? */ | |
476 | ret = -EINVAL; | |
477 | return ret; | |
478 | } | |
479 | ||
480 | static struct uart_ops lh7a40x_uart_ops = { | |
481 | .tx_empty = lh7a40xuart_tx_empty, | |
482 | .set_mctrl = lh7a40xuart_set_mctrl, | |
483 | .get_mctrl = lh7a40xuart_get_mctrl, | |
484 | .stop_tx = lh7a40xuart_stop_tx, | |
485 | .start_tx = lh7a40xuart_start_tx, | |
486 | .stop_rx = lh7a40xuart_stop_rx, | |
487 | .enable_ms = lh7a40xuart_enable_ms, | |
488 | .break_ctl = lh7a40xuart_break_ctl, | |
489 | .startup = lh7a40xuart_startup, | |
490 | .shutdown = lh7a40xuart_shutdown, | |
491 | .set_termios = lh7a40xuart_set_termios, | |
492 | .type = lh7a40xuart_type, | |
493 | .release_port = lh7a40xuart_release_port, | |
494 | .request_port = lh7a40xuart_request_port, | |
495 | .config_port = lh7a40xuart_config_port, | |
496 | .verify_port = lh7a40xuart_verify_port, | |
497 | }; | |
498 | ||
499 | static struct uart_port_lh7a40x lh7a40x_ports[DEV_NR] = { | |
500 | { | |
501 | .port = { | |
502 | .membase = (void*) io_p2v (UART1_PHYS), | |
503 | .mapbase = UART1_PHYS, | |
504 | .iotype = SERIAL_IO_MEM, | |
505 | .irq = IRQ_UART1INTR, | |
506 | .uartclk = 14745600/2, | |
507 | .fifosize = 16, | |
508 | .ops = &lh7a40x_uart_ops, | |
ce8337cb | 509 | .flags = UPF_BOOT_AUTOCONF, |
1da177e4 LT |
510 | .line = 0, |
511 | }, | |
512 | }, | |
513 | { | |
514 | .port = { | |
515 | .membase = (void*) io_p2v (UART2_PHYS), | |
516 | .mapbase = UART2_PHYS, | |
517 | .iotype = SERIAL_IO_MEM, | |
518 | .irq = IRQ_UART2INTR, | |
519 | .uartclk = 14745600/2, | |
520 | .fifosize = 16, | |
521 | .ops = &lh7a40x_uart_ops, | |
ce8337cb | 522 | .flags = UPF_BOOT_AUTOCONF, |
1da177e4 LT |
523 | .line = 1, |
524 | }, | |
525 | }, | |
526 | { | |
527 | .port = { | |
528 | .membase = (void*) io_p2v (UART3_PHYS), | |
529 | .mapbase = UART3_PHYS, | |
530 | .iotype = SERIAL_IO_MEM, | |
531 | .irq = IRQ_UART3INTR, | |
532 | .uartclk = 14745600/2, | |
533 | .fifosize = 16, | |
534 | .ops = &lh7a40x_uart_ops, | |
ce8337cb | 535 | .flags = UPF_BOOT_AUTOCONF, |
1da177e4 LT |
536 | .line = 2, |
537 | }, | |
538 | }, | |
539 | }; | |
540 | ||
541 | #ifndef CONFIG_SERIAL_LH7A40X_CONSOLE | |
542 | # define LH7A40X_CONSOLE NULL | |
543 | #else | |
544 | # define LH7A40X_CONSOLE &lh7a40x_console | |
545 | ||
546 | ||
547 | static void lh7a40xuart_console_write (struct console* co, | |
548 | const char* s, | |
549 | unsigned int count) | |
550 | { | |
551 | struct uart_port* port = &lh7a40x_ports[co->index].port; | |
552 | unsigned int con = UR (port, UART_R_CON); | |
553 | unsigned int inten = UR (port, UART_R_INTEN); | |
554 | ||
555 | ||
556 | UR (port, UART_R_INTEN) = 0; /* Disable all interrupts */ | |
557 | BIT_SET (port, UART_R_CON, UARTEN | SIRDIS); /* Enable UART */ | |
558 | ||
559 | for (; count-- > 0; ++s) { | |
560 | while (UR (port, UART_R_STATUS) & nTxRdy) | |
561 | ; | |
562 | UR (port, UART_R_DATA) = *s; | |
563 | if (*s == '\n') { | |
564 | while ((UR (port, UART_R_STATUS) & TxBusy)) | |
565 | ; | |
566 | UR (port, UART_R_DATA) = '\r'; | |
567 | } | |
568 | } | |
569 | ||
570 | /* Wait until all characters are sent */ | |
571 | while (UR (port, UART_R_STATUS) & TxBusy) | |
572 | ; | |
573 | ||
574 | /* Restore control and interrupt mask */ | |
575 | UR (port, UART_R_CON) = con; | |
576 | UR (port, UART_R_INTEN) = inten; | |
577 | } | |
578 | ||
579 | static void __init lh7a40xuart_console_get_options (struct uart_port* port, | |
580 | int* baud, | |
581 | int* parity, | |
582 | int* bits) | |
583 | { | |
584 | if (UR (port, UART_R_CON) & UARTEN) { | |
585 | unsigned int fcon = UR (port, UART_R_FCON); | |
586 | unsigned int quot = UR (port, UART_R_BRCON) + 1; | |
587 | ||
588 | switch (fcon & (PEN | EPS)) { | |
589 | default: *parity = 'n'; break; | |
590 | case PEN: *parity = 'o'; break; | |
591 | case PEN | EPS: *parity = 'e'; break; | |
592 | } | |
593 | ||
594 | switch (fcon & WLEN) { | |
595 | default: | |
596 | case WLEN_8: *bits = 8; break; | |
597 | case WLEN_7: *bits = 7; break; | |
598 | case WLEN_6: *bits = 6; break; | |
599 | case WLEN_5: *bits = 5; break; | |
600 | } | |
601 | ||
602 | *baud = port->uartclk/(16*quot); | |
603 | } | |
604 | } | |
605 | ||
606 | static int __init lh7a40xuart_console_setup (struct console* co, char* options) | |
607 | { | |
608 | struct uart_port* port; | |
609 | int baud = 38400; | |
610 | int bits = 8; | |
611 | int parity = 'n'; | |
612 | int flow = 'n'; | |
613 | ||
614 | if (co->index >= DEV_NR) /* Bounds check on device number */ | |
615 | co->index = 0; | |
616 | port = &lh7a40x_ports[co->index].port; | |
617 | ||
618 | if (options) | |
619 | uart_parse_options (options, &baud, &parity, &bits, &flow); | |
620 | else | |
621 | lh7a40xuart_console_get_options (port, &baud, &parity, &bits); | |
622 | ||
623 | return uart_set_options (port, co, baud, parity, bits, flow); | |
624 | } | |
625 | ||
2d93486c | 626 | static struct uart_driver lh7a40x_reg; |
1da177e4 LT |
627 | static struct console lh7a40x_console = { |
628 | .name = "ttyAM", | |
629 | .write = lh7a40xuart_console_write, | |
630 | .device = uart_console_device, | |
631 | .setup = lh7a40xuart_console_setup, | |
632 | .flags = CON_PRINTBUFFER, | |
633 | .index = -1, | |
634 | .data = &lh7a40x_reg, | |
635 | }; | |
636 | ||
637 | static int __init lh7a40xuart_console_init(void) | |
638 | { | |
639 | register_console (&lh7a40x_console); | |
640 | return 0; | |
641 | } | |
642 | ||
643 | console_initcall (lh7a40xuart_console_init); | |
644 | ||
645 | #endif | |
646 | ||
647 | static struct uart_driver lh7a40x_reg = { | |
648 | .owner = THIS_MODULE, | |
649 | .driver_name = "ttyAM", | |
650 | .dev_name = "ttyAM", | |
651 | .major = DEV_MAJOR, | |
652 | .minor = DEV_MINOR, | |
653 | .nr = DEV_NR, | |
654 | .cons = LH7A40X_CONSOLE, | |
655 | }; | |
656 | ||
657 | static int __init lh7a40xuart_init(void) | |
658 | { | |
659 | int ret; | |
660 | ||
661 | printk (KERN_INFO "serial: LH7A40X serial driver\n"); | |
662 | ||
663 | ret = uart_register_driver (&lh7a40x_reg); | |
664 | ||
665 | if (ret == 0) { | |
666 | int i; | |
667 | ||
668 | for (i = 0; i < DEV_NR; i++) | |
669 | uart_add_one_port (&lh7a40x_reg, | |
670 | &lh7a40x_ports[i].port); | |
671 | } | |
672 | return ret; | |
673 | } | |
674 | ||
675 | static void __exit lh7a40xuart_exit(void) | |
676 | { | |
677 | int i; | |
678 | ||
679 | for (i = 0; i < DEV_NR; i++) | |
680 | uart_remove_one_port (&lh7a40x_reg, &lh7a40x_ports[i].port); | |
681 | ||
682 | uart_unregister_driver (&lh7a40x_reg); | |
683 | } | |
684 | ||
685 | module_init (lh7a40xuart_init); | |
686 | module_exit (lh7a40xuart_exit); | |
687 | ||
688 | MODULE_AUTHOR ("Marc Singer"); | |
689 | MODULE_DESCRIPTION ("Sharp LH7A40X serial port driver"); | |
690 | MODULE_LICENSE ("GPL"); |