[mirror_ubuntu-artful-kernel.git] / drivers / spi / xilinx_spi.c

/*
 * xilinx_spi.c
 *
 * Xilinx SPI controller driver (master mode only)
 *
 * Author: MontaVista Software, Inc.
 *	source@mvista.com
 *
 * 2002-2007 (c) MontaVista Software, Inc.  This file is licensed under the
 * terms of the GNU General Public License version 2.  This program is licensed
 * "as is" without any warranty of any kind, whether express or implied.
 */

#include <linux/module.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/platform_device.h>

#include <linux/of_platform.h>
#include <linux/of_device.h>
#include <linux/of_spi.h>

#include <linux/spi/spi.h>
#include <linux/spi/spi_bitbang.h>
#include <linux/io.h>

#define XILINX_SPI_NAME "xilinx_spi"

/* Register definitions as per "OPB Serial Peripheral Interface (SPI) (v1.00e)
 * Product Specification", DS464
 */
#define XSPI_CR_OFFSET		0x62	/* 16-bit Control Register */

#define XSPI_CR_ENABLE		0x02
#define XSPI_CR_MASTER_MODE	0x04
#define XSPI_CR_CPOL		0x08
#define XSPI_CR_CPHA		0x10
#define XSPI_CR_MODE_MASK	(XSPI_CR_CPHA | XSPI_CR_CPOL)
#define XSPI_CR_TXFIFO_RESET	0x20
#define XSPI_CR_RXFIFO_RESET	0x40
#define XSPI_CR_MANUAL_SSELECT	0x80
#define XSPI_CR_TRANS_INHIBIT	0x100

#define XSPI_SR_OFFSET		0x67	/* 8-bit Status Register */

#define XSPI_SR_RX_EMPTY_MASK	0x01	/* Receive FIFO is empty */
#define XSPI_SR_RX_FULL_MASK	0x02	/* Receive FIFO is full */
#define XSPI_SR_TX_EMPTY_MASK	0x04	/* Transmit FIFO is empty */
#define XSPI_SR_TX_FULL_MASK	0x08	/* Transmit FIFO is full */
#define XSPI_SR_MODE_FAULT_MASK	0x10	/* Mode fault error */

#define XSPI_TXD_OFFSET		0x6b	/* 8-bit Data Transmit Register */
#define XSPI_RXD_OFFSET		0x6f	/* 8-bit Data Receive Register */

#define XSPI_SSR_OFFSET		0x70	/* 32-bit Slave Select Register */

/* Register definitions as per "OPB IPIF (v3.01c) Product Specification", DS414
 * IPIF registers are 32 bit
 */
#define XIPIF_V123B_DGIER_OFFSET	0x1c	/* IPIF global int enable reg */
#define XIPIF_V123B_GINTR_ENABLE	0x80000000

#define XIPIF_V123B_IISR_OFFSET		0x20	/* IPIF interrupt status reg */
#define XIPIF_V123B_IIER_OFFSET		0x28	/* IPIF interrupt enable reg */

#define XSPI_INTR_MODE_FAULT		0x01	/* Mode fault error */
#define XSPI_INTR_SLAVE_MODE_FAULT	0x02	/* Selected as slave while
						 * disabled */
#define XSPI_INTR_TX_EMPTY		0x04	/* TxFIFO is empty */
#define XSPI_INTR_TX_UNDERRUN		0x08	/* TxFIFO was underrun */
#define XSPI_INTR_RX_FULL		0x10	/* RxFIFO is full */
#define XSPI_INTR_RX_OVERRUN		0x20	/* RxFIFO was overrun */

#define XIPIF_V123B_RESETR_OFFSET	0x40	/* IPIF reset register */
#define XIPIF_V123B_RESET_MASK		0x0a	/* the value to write */

struct xilinx_spi {
	/* bitbang has to be first */
	struct spi_bitbang bitbang;
	struct completion done;

	void __iomem	*regs;	/* virt. address of the control registers */

	u32		irq;

	u32		speed_hz; /* SCK has a fixed frequency of speed_hz Hz */

	u8 *rx_ptr;		/* pointer in the Tx buffer */
	const u8 *tx_ptr;	/* pointer in the Rx buffer */
	int remaining_bytes;	/* the number of bytes left to transfer */
};

static void xspi_init_hw(void __iomem *regs_base)
{
	/* Reset the SPI device */
	out_be32(regs_base + XIPIF_V123B_RESETR_OFFSET,
		 XIPIF_V123B_RESET_MASK);
	/* Disable all the interrupts just in case */
	out_be32(regs_base + XIPIF_V123B_IIER_OFFSET, 0);
	/* Enable the global IPIF interrupt */
	out_be32(regs_base + XIPIF_V123B_DGIER_OFFSET,
		 XIPIF_V123B_GINTR_ENABLE);
	/* Deselect the slave on the SPI bus */
	out_be32(regs_base + XSPI_SSR_OFFSET, 0xffff);
	/* Disable the transmitter, enable Manual Slave Select Assertion,
	 * put SPI controller into master mode, and enable it */
	out_be16(regs_base + XSPI_CR_OFFSET,
		 XSPI_CR_TRANS_INHIBIT | XSPI_CR_MANUAL_SSELECT
		 | XSPI_CR_MASTER_MODE | XSPI_CR_ENABLE);
}

static void xilinx_spi_chipselect(struct spi_device *spi, int is_on)
{
	struct xilinx_spi *xspi = spi_master_get_devdata(spi->master);

	if (is_on == BITBANG_CS_INACTIVE) {
		/* Deselect the slave on the SPI bus */
		out_be32(xspi->regs + XSPI_SSR_OFFSET, 0xffff);
	} else if (is_on == BITBANG_CS_ACTIVE) {
		/* Set the SPI clock phase and polarity */
		u16 cr = in_be16(xspi->regs + XSPI_CR_OFFSET)
			 & ~XSPI_CR_MODE_MASK;
		if (spi->mode & SPI_CPHA)
			cr |= XSPI_CR_CPHA;
		if (spi->mode & SPI_CPOL)
			cr |= XSPI_CR_CPOL;
		out_be16(xspi->regs + XSPI_CR_OFFSET, cr);

		/* We do not check spi->max_speed_hz here as the SPI clock
		 * frequency is not software programmable (the IP block design
		 * parameter)
		 */

		/* Activate the chip select */
		out_be32(xspi->regs + XSPI_SSR_OFFSET,
			 ~(0x0001 << spi->chip_select));
	}
}

/* spi_bitbang requires custom setup_transfer() to be defined if there is a
 * custom txrx_bufs(). We have nothing to setup here as the SPI IP block
 * supports just 8 bits per word, and SPI clock can't be changed in software.
 * Check for 8 bits per word. Chip select delay calculations could be
 * added here as soon as bitbang_work() can be made aware of the delay value.
 */
static int xilinx_spi_setup_transfer(struct spi_device *spi,
		struct spi_transfer *t)
{
	u8 bits_per_word;

	bits_per_word = (t) ? t->bits_per_word : spi->bits_per_word;
	if (bits_per_word != 8) {
		dev_err(&spi->dev, "%s, unsupported bits_per_word=%d\n",
			__func__, bits_per_word);
		return -EINVAL;
	}

	return 0;
}

static int xilinx_spi_setup(struct spi_device *spi)
{
	struct spi_bitbang *bitbang;
	struct xilinx_spi *xspi;
	int retval;

	xspi = spi_master_get_devdata(spi->master);
	bitbang = &xspi->bitbang;

	retval = xilinx_spi_setup_transfer(spi, NULL);
	if (retval < 0)
		return retval;

	return 0;
}

static void xilinx_spi_fill_tx_fifo(struct xilinx_spi *xspi)
{
	u8 sr;

	/* Fill the Tx FIFO with as many bytes as possible */
	sr = in_8(xspi->regs + XSPI_SR_OFFSET);
	while ((sr & XSPI_SR_TX_FULL_MASK) == 0 && xspi->remaining_bytes > 0) {
		if (xspi->tx_ptr) {
			out_8(xspi->regs + XSPI_TXD_OFFSET, *xspi->tx_ptr++);
		} else {
			out_8(xspi->regs + XSPI_TXD_OFFSET, 0);
		}
		xspi->remaining_bytes--;
		sr = in_8(xspi->regs + XSPI_SR_OFFSET);
	}
}

static int xilinx_spi_txrx_bufs(struct spi_device *spi, struct spi_transfer *t)
{
	struct xilinx_spi *xspi = spi_master_get_devdata(spi->master);
	u32 ipif_ier;
	u16 cr;

	/* We get here with transmitter inhibited */

	xspi->tx_ptr = t->tx_buf;
	xspi->rx_ptr = t->rx_buf;
	xspi->remaining_bytes = t->len;
	INIT_COMPLETION(xspi->done);

	xilinx_spi_fill_tx_fifo(xspi);

	/* Enable the transmit empty interrupt, which we use to determine
	 * progress on the transmission.
	 */
	ipif_ier = in_be32(xspi->regs + XIPIF_V123B_IIER_OFFSET);
	out_be32(xspi->regs + XIPIF_V123B_IIER_OFFSET,
		 ipif_ier | XSPI_INTR_TX_EMPTY);

	/* Start the transfer by not inhibiting the transmitter any longer */
	cr = in_be16(xspi->regs + XSPI_CR_OFFSET) & ~XSPI_CR_TRANS_INHIBIT;
	out_be16(xspi->regs + XSPI_CR_OFFSET, cr);

	wait_for_completion(&xspi->done);

	/* Disable the transmit empty interrupt */
	out_be32(xspi->regs + XIPIF_V123B_IIER_OFFSET, ipif_ier);

	return t->len - xspi->remaining_bytes;
}


/* This driver supports single master mode only. Hence Tx FIFO Empty
 * is the only interrupt we care about.
 * Receive FIFO Overrun, Transmit FIFO Underrun, Mode Fault, and Slave Mode
 * Fault are not to happen.
 */
static irqreturn_t xilinx_spi_irq(int irq, void *dev_id)
{
	struct xilinx_spi *xspi = dev_id;
	u32 ipif_isr;

	/* Get the IPIF interrupts, and clear them immediately */
	ipif_isr = in_be32(xspi->regs + XIPIF_V123B_IISR_OFFSET);
	out_be32(xspi->regs + XIPIF_V123B_IISR_OFFSET, ipif_isr);

	if (ipif_isr & XSPI_INTR_TX_EMPTY) {	/* Transmission completed */
		u16 cr;
		u8 sr;

		/* A transmit has just completed. Process received data and
		 * check for more data to transmit. Always inhibit the
		 * transmitter while the Isr refills the transmit register/FIFO,
		 * or make sure it is stopped if we're done.
		 */
		cr = in_be16(xspi->regs + XSPI_CR_OFFSET);
		out_be16(xspi->regs + XSPI_CR_OFFSET,
			 cr | XSPI_CR_TRANS_INHIBIT);

		/* Read out all the data from the Rx FIFO */
		sr = in_8(xspi->regs + XSPI_SR_OFFSET);
		while ((sr & XSPI_SR_RX_EMPTY_MASK) == 0) {
			u8 data;

			data = in_8(xspi->regs + XSPI_RXD_OFFSET);
			if (xspi->rx_ptr) {
				*xspi->rx_ptr++ = data;
			}
			sr = in_8(xspi->regs + XSPI_SR_OFFSET);
		}

		/* See if there is more data to send */
		if (xspi->remaining_bytes > 0) {
			xilinx_spi_fill_tx_fifo(xspi);
			/* Start the transfer by not inhibiting the
			 * transmitter any longer
			 */
			out_be16(xspi->regs + XSPI_CR_OFFSET, cr);
		} else {
			/* No more data to send.
			 * Indicate the transfer is completed.
			 */
			complete(&xspi->done);
		}
	}

	return IRQ_HANDLED;
}

static int __init xilinx_spi_of_probe(struct of_device *ofdev,
					const struct of_device_id *match)
{
	struct spi_master *master;
	struct xilinx_spi *xspi;
	struct resource r_irq_struct;
	struct resource r_mem_struct;

	struct resource *r_irq = &r_irq_struct;
	struct resource *r_mem = &r_mem_struct;
	int rc = 0;
	const u32 *prop;
	int len;

	/* Get resources(memory, IRQ) associated with the device */
	master = spi_alloc_master(&ofdev->dev, sizeof(struct xilinx_spi));

	if (master == NULL) {
		return -ENOMEM;
	}

	dev_set_drvdata(&ofdev->dev, master);

	rc = of_address_to_resource(ofdev->node, 0, r_mem);
	if (rc) {
		dev_warn(&ofdev->dev, "invalid address\n");
		goto put_master;
	}

	rc = of_irq_to_resource(ofdev->node, 0, r_irq);
	if (rc == NO_IRQ) {
		dev_warn(&ofdev->dev, "no IRQ found\n");
		goto put_master;
	}

	/* the spi->mode bits understood by this driver: */
	master->mode_bits = SPI_CPOL | SPI_CPHA;

	xspi = spi_master_get_devdata(master);
	xspi->bitbang.master = spi_master_get(master);
	xspi->bitbang.chipselect = xilinx_spi_chipselect;
	xspi->bitbang.setup_transfer = xilinx_spi_setup_transfer;
	xspi->bitbang.txrx_bufs = xilinx_spi_txrx_bufs;
	xspi->bitbang.master->setup = xilinx_spi_setup;
	init_completion(&xspi->done);

	xspi->irq = r_irq->start;

	if (!request_mem_region(r_mem->start,
			r_mem->end - r_mem->start + 1, XILINX_SPI_NAME)) {
		rc = -ENXIO;
		dev_warn(&ofdev->dev, "memory request failure\n");
		goto put_master;
	}

	xspi->regs = ioremap(r_mem->start, r_mem->end - r_mem->start + 1);
	if (xspi->regs == NULL) {
		rc = -ENOMEM;
		dev_warn(&ofdev->dev, "ioremap failure\n");
		goto release_mem;
	}
	xspi->irq = r_irq->start;

	/* dynamic bus assignment */
	master->bus_num = -1;

	/* number of slave select bits is required */
	prop = of_get_property(ofdev->node, "xlnx,num-ss-bits", &len);
	if (!prop || len < sizeof(*prop)) {
		dev_warn(&ofdev->dev, "no 'xlnx,num-ss-bits' property\n");
		goto unmap_io;
	}
	master->num_chipselect = *prop;

	/* SPI controller initializations */
	xspi_init_hw(xspi->regs);

	/* Register for SPI Interrupt */
	rc = request_irq(xspi->irq, xilinx_spi_irq, 0, XILINX_SPI_NAME, xspi);
	if (rc != 0) {
		dev_warn(&ofdev->dev, "irq request failure: %d\n", xspi->irq);
		goto unmap_io;
	}

	rc = spi_bitbang_start(&xspi->bitbang);
	if (rc != 0) {
		dev_err(&ofdev->dev, "spi_bitbang_start FAILED\n");
		goto free_irq;
	}

	dev_info(&ofdev->dev, "at 0x%08X mapped to 0x%08X, irq=%d\n",
			(unsigned int)r_mem->start, (u32)xspi->regs, xspi->irq);

	/* Add any subnodes on the SPI bus */
	of_register_spi_devices(master, ofdev->node);

	return rc;

free_irq:
	free_irq(xspi->irq, xspi);
unmap_io:
	iounmap(xspi->regs);
release_mem:
	release_mem_region(r_mem->start, resource_size(r_mem));
put_master:
	spi_master_put(master);
	return rc;
}

static int __devexit xilinx_spi_remove(struct of_device *ofdev)
{
	struct xilinx_spi *xspi;
	struct spi_master *master;
	struct resource r_mem;

	master = platform_get_drvdata(ofdev);
	xspi = spi_master_get_devdata(master);

	spi_bitbang_stop(&xspi->bitbang);
	free_irq(xspi->irq, xspi);
	iounmap(xspi->regs);
	if (!of_address_to_resource(ofdev->node, 0, &r_mem))
		release_mem_region(r_mem.start, resource_size(&r_mem));
	dev_set_drvdata(&ofdev->dev, 0);
	spi_master_put(xspi->bitbang.master);

	return 0;
}

/* work with hotplug and coldplug */
MODULE_ALIAS("platform:" XILINX_SPI_NAME);

static int __exit xilinx_spi_of_remove(struct of_device *op)
{
	return xilinx_spi_remove(op);
}

static struct of_device_id xilinx_spi_of_match[] = {
	{ .compatible = "xlnx,xps-spi-2.00.a", },
	{ .compatible = "xlnx,xps-spi-2.00.b", },
	{}
};

MODULE_DEVICE_TABLE(of, xilinx_spi_of_match);

static struct of_platform_driver xilinx_spi_of_driver = {
	.owner = THIS_MODULE,
	.name = "xilinx-xps-spi",
	.match_table = xilinx_spi_of_match,
	.probe = xilinx_spi_of_probe,
	.remove = __exit_p(xilinx_spi_of_remove),
	.driver = {
		.name = "xilinx-xps-spi",
		.owner = THIS_MODULE,
	},
};

static int __init xilinx_spi_init(void)
{
	return of_register_platform_driver(&xilinx_spi_of_driver);
}
module_init(xilinx_spi_init);

static void __exit xilinx_spi_exit(void)
{
	of_unregister_platform_driver(&xilinx_spi_of_driver);
}
module_exit(xilinx_spi_exit);
MODULE_AUTHOR("MontaVista Software, Inc. <source@mvista.com>");
MODULE_DESCRIPTION("Xilinx SPI driver");
MODULE_LICENSE("GPL");
Commit	Line	Data
ae918c02 AK	1	/*
	2	* xilinx_spi.c
	3	*
	4	* Xilinx SPI controller driver (master mode only)
	5	*
	6	* Author: MontaVista Software, Inc.
	7	* source@mvista.com
	8	*
	9	* 2002-2007 (c) MontaVista Software, Inc. This file is licensed under the
	10	* terms of the GNU General Public License version 2. This program is licensed
	11	* "as is" without any warranty of any kind, whether express or implied.
	12	*/
	13
	14	#include <linux/module.h>
	15	#include <linux/init.h>
	16	#include <linux/interrupt.h>
	17	#include <linux/platform_device.h>
ff82c587 JL	18
	19	#include <linux/of_platform.h>
	20	#include <linux/of_device.h>
	21	#include <linux/of_spi.h>
	22
ae918c02 AK	23	#include <linux/spi/spi.h>
	24	#include <linux/spi/spi_bitbang.h>
	25	#include <linux/io.h>
	26
fc3ba952	27	#define XILINX_SPI_NAME "xilinx_spi"
ae918c02 AK	28
	29	/* Register definitions as per "OPB Serial Peripheral Interface (SPI) (v1.00e)
	30	* Product Specification", DS464
	31	*/
	32	#define XSPI_CR_OFFSET 0x62 /* 16-bit Control Register */
	33
	34	#define XSPI_CR_ENABLE 0x02
	35	#define XSPI_CR_MASTER_MODE 0x04
	36	#define XSPI_CR_CPOL 0x08
	37	#define XSPI_CR_CPHA 0x10
	38	#define XSPI_CR_MODE_MASK (XSPI_CR_CPHA \| XSPI_CR_CPOL)
	39	#define XSPI_CR_TXFIFO_RESET 0x20
	40	#define XSPI_CR_RXFIFO_RESET 0x40
	41	#define XSPI_CR_MANUAL_SSELECT 0x80
	42	#define XSPI_CR_TRANS_INHIBIT 0x100
	43
	44	#define XSPI_SR_OFFSET 0x67 /* 8-bit Status Register */
	45
	46	#define XSPI_SR_RX_EMPTY_MASK 0x01 /* Receive FIFO is empty */
	47	#define XSPI_SR_RX_FULL_MASK 0x02 /* Receive FIFO is full */
	48	#define XSPI_SR_TX_EMPTY_MASK 0x04 /* Transmit FIFO is empty */
	49	#define XSPI_SR_TX_FULL_MASK 0x08 /* Transmit FIFO is full */
	50	#define XSPI_SR_MODE_FAULT_MASK 0x10 /* Mode fault error */
	51
	52	#define XSPI_TXD_OFFSET 0x6b /* 8-bit Data Transmit Register */
	53	#define XSPI_RXD_OFFSET 0x6f /* 8-bit Data Receive Register */
	54
	55	#define XSPI_SSR_OFFSET 0x70 /* 32-bit Slave Select Register */
	56
	57	/* Register definitions as per "OPB IPIF (v3.01c) Product Specification", DS414
	58	* IPIF registers are 32 bit
	59	*/
	60	#define XIPIF_V123B_DGIER_OFFSET 0x1c /* IPIF global int enable reg */
	61	#define XIPIF_V123B_GINTR_ENABLE 0x80000000
	62
	63	#define XIPIF_V123B_IISR_OFFSET 0x20 /* IPIF interrupt status reg */
	64	#define XIPIF_V123B_IIER_OFFSET 0x28 /* IPIF interrupt enable reg */
	65
	66	#define XSPI_INTR_MODE_FAULT 0x01 /* Mode fault error */
	67	#define XSPI_INTR_SLAVE_MODE_FAULT 0x02 /* Selected as slave while
	68	* disabled */
	69	#define XSPI_INTR_TX_EMPTY 0x04 /* TxFIFO is empty */
	70	#define XSPI_INTR_TX_UNDERRUN 0x08 /* TxFIFO was underrun */
	71	#define XSPI_INTR_RX_FULL 0x10 /* RxFIFO is full */
	72	#define XSPI_INTR_RX_OVERRUN 0x20 /* RxFIFO was overrun */
	73
	74	#define XIPIF_V123B_RESETR_OFFSET 0x40 /* IPIF reset register */
	75	#define XIPIF_V123B_RESET_MASK 0x0a /* the value to write */
	76
	77	struct xilinx_spi {
	78	/* bitbang has to be first */
	79	struct spi_bitbang bitbang;
	80	struct completion done;
	81
	82	void __iomem regs; / virt. address of the control registers */
	83
	84	u32 irq;
	85
	86	u32 speed_hz; /* SCK has a fixed frequency of speed_hz Hz */
	87
	88	u8 rx_ptr; / pointer in the Tx buffer */
	89	const u8 tx_ptr; / pointer in the Rx buffer */
	90	int remaining_bytes; /* the number of bytes left to transfer */
	91	};
92
93	static void xspi_init_hw(void __iomem *regs_base)
94	{
95	/* Reset the SPI device */
96	out_be32(regs_base + XIPIF_V123B_RESETR_OFFSET,
97	XIPIF_V123B_RESET_MASK);
98	/* Disable all the interrupts just in case */
99	out_be32(regs_base + XIPIF_V123B_IIER_OFFSET, 0);
100	/* Enable the global IPIF interrupt */
101	out_be32(regs_base + XIPIF_V123B_DGIER_OFFSET,
102	XIPIF_V123B_GINTR_ENABLE);
103	/* Deselect the slave on the SPI bus */
104	out_be32(regs_base + XSPI_SSR_OFFSET, 0xffff);
105	/* Disable the transmitter, enable Manual Slave Select Assertion,
106	* put SPI controller into master mode, and enable it */
107	out_be16(regs_base + XSPI_CR_OFFSET,
108	XSPI_CR_TRANS_INHIBIT \| XSPI_CR_MANUAL_SSELECT
109	\| XSPI_CR_MASTER_MODE \| XSPI_CR_ENABLE);
110	}
111
112	static void xilinx_spi_chipselect(struct spi_device *spi, int is_on)
113	{
114	struct xilinx_spi *xspi = spi_master_get_devdata(spi->master);
115
116	if (is_on == BITBANG_CS_INACTIVE) {
117	/* Deselect the slave on the SPI bus */
118	out_be32(xspi->regs + XSPI_SSR_OFFSET, 0xffff);
119	} else if (is_on == BITBANG_CS_ACTIVE) {
120	/* Set the SPI clock phase and polarity */
121	u16 cr = in_be16(xspi->regs + XSPI_CR_OFFSET)
122	& ~XSPI_CR_MODE_MASK;
123	if (spi->mode & SPI_CPHA)
124	cr \|= XSPI_CR_CPHA;
125	if (spi->mode & SPI_CPOL)
126	cr \|= XSPI_CR_CPOL;
127	out_be16(xspi->regs + XSPI_CR_OFFSET, cr);
128
129	/* We do not check spi->max_speed_hz here as the SPI clock
130	* frequency is not software programmable (the IP block design
131	* parameter)
132	*/
133
134	/* Activate the chip select */
135	out_be32(xspi->regs + XSPI_SSR_OFFSET,
136	~(0x0001 << spi->chip_select));
137	}
138	}
139
140	/* spi_bitbang requires custom setup_transfer() to be defined if there is a
141	* custom txrx_bufs(). We have nothing to setup here as the SPI IP block
142	* supports just 8 bits per word, and SPI clock can't be changed in software.
143	* Check for 8 bits per word. Chip select delay calculations could be
144	* added here as soon as bitbang_work() can be made aware of the delay value.
145	*/
146	static int xilinx_spi_setup_transfer(struct spi_device *spi,
147	struct spi_transfer *t)
148	{
149	u8 bits_per_word;
ae918c02 AK	150
ae918c02 AK	151	bits_per_word = (t) ? t->bits_per_word : spi->bits_per_word;
ae918c02 AK	152	if (bits_per_word != 8) {
ae918c02 AK	153	dev_err(&spi->dev, "%s, unsupported bits_per_word=%d\n",
b687d2a8	154	__func__, bits_per_word);
ae918c02 AK	155	return -EINVAL;
	156	}
	157
ae918c02 AK	158	return 0;
	159	}
	160
ae918c02 AK	161	static int xilinx_spi_setup(struct spi_device *spi)
	162	{
	163	struct spi_bitbang *bitbang;
	164	struct xilinx_spi *xspi;
	165	int retval;
	166
	167	xspi = spi_master_get_devdata(spi->master);
	168	bitbang = &xspi->bitbang;
	169
ae918c02 AK	170	retval = xilinx_spi_setup_transfer(spi, NULL);
	171	if (retval < 0)
	172	return retval;
	173
ae918c02 AK	174	return 0;
	175	}
	176
	177	static void xilinx_spi_fill_tx_fifo(struct xilinx_spi *xspi)
	178	{
	179	u8 sr;
	180
	181	/* Fill the Tx FIFO with as many bytes as possible */
	182	sr = in_8(xspi->regs + XSPI_SR_OFFSET);
	183	while ((sr & XSPI_SR_TX_FULL_MASK) == 0 && xspi->remaining_bytes > 0) {
	184	if (xspi->tx_ptr) {
	185	out_8(xspi->regs + XSPI_TXD_OFFSET, *xspi->tx_ptr++);
	186	} else {
	187	out_8(xspi->regs + XSPI_TXD_OFFSET, 0);
	188	}
	189	xspi->remaining_bytes--;
	190	sr = in_8(xspi->regs + XSPI_SR_OFFSET);
	191	}
	192	}
	193
	194	static int xilinx_spi_txrx_bufs(struct spi_device spi, struct spi_transfer t)
	195	{
	196	struct xilinx_spi *xspi = spi_master_get_devdata(spi->master);
	197	u32 ipif_ier;
	198	u16 cr;
	199
	200	/* We get here with transmitter inhibited */
	201
	202	xspi->tx_ptr = t->tx_buf;
	203	xspi->rx_ptr = t->rx_buf;
	204	xspi->remaining_bytes = t->len;
	205	INIT_COMPLETION(xspi->done);
	206
	207	xilinx_spi_fill_tx_fifo(xspi);
	208
	209	/* Enable the transmit empty interrupt, which we use to determine
	210	* progress on the transmission.
	211	*/
	212	ipif_ier = in_be32(xspi->regs + XIPIF_V123B_IIER_OFFSET);
	213	out_be32(xspi->regs + XIPIF_V123B_IIER_OFFSET,
	214	ipif_ier \| XSPI_INTR_TX_EMPTY);
	215
	216	/* Start the transfer by not inhibiting the transmitter any longer */
	217	cr = in_be16(xspi->regs + XSPI_CR_OFFSET) & ~XSPI_CR_TRANS_INHIBIT;
	218	out_be16(xspi->regs + XSPI_CR_OFFSET, cr);
	219
	220	wait_for_completion(&xspi->done);
	221
	222	/* Disable the transmit empty interrupt */
	223	out_be32(xspi->regs + XIPIF_V123B_IIER_OFFSET, ipif_ier);
	224
	225	return t->len - xspi->remaining_bytes;
	226	}
	227
	228
	229	/* This driver supports single master mode only. Hence Tx FIFO Empty
	230	* is the only interrupt we care about.
	231	* Receive FIFO Overrun, Transmit FIFO Underrun, Mode Fault, and Slave Mode
	232	* Fault are not to happen.
	233	*/
	234	static irqreturn_t xilinx_spi_irq(int irq, void *dev_id)
	235	{
	236	struct xilinx_spi *xspi = dev_id;
	237	u32 ipif_isr;
238
239	/* Get the IPIF interrupts, and clear them immediately */
240	ipif_isr = in_be32(xspi->regs + XIPIF_V123B_IISR_OFFSET);
241	out_be32(xspi->regs + XIPIF_V123B_IISR_OFFSET, ipif_isr);
242
243	if (ipif_isr & XSPI_INTR_TX_EMPTY) { /* Transmission completed */
244	u16 cr;
245	u8 sr;
246
247	/* A transmit has just completed. Process received data and
248	* check for more data to transmit. Always inhibit the
249	* transmitter while the Isr refills the transmit register/FIFO,
250	* or make sure it is stopped if we're done.
251	*/
252	cr = in_be16(xspi->regs + XSPI_CR_OFFSET);
253	out_be16(xspi->regs + XSPI_CR_OFFSET,
254	cr \| XSPI_CR_TRANS_INHIBIT);
255
256	/* Read out all the data from the Rx FIFO */
257	sr = in_8(xspi->regs + XSPI_SR_OFFSET);
258	while ((sr & XSPI_SR_RX_EMPTY_MASK) == 0) {
259	u8 data;
260
261	data = in_8(xspi->regs + XSPI_RXD_OFFSET);
262	if (xspi->rx_ptr) {
263	*xspi->rx_ptr++ = data;
264	}
265	sr = in_8(xspi->regs + XSPI_SR_OFFSET);
266	}
267
268	/* See if there is more data to send */
269	if (xspi->remaining_bytes > 0) {
270	xilinx_spi_fill_tx_fifo(xspi);
271	/* Start the transfer by not inhibiting the
272	* transmitter any longer
273	*/
274	out_be16(xspi->regs + XSPI_CR_OFFSET, cr);
275	} else {
276	/* No more data to send.
277	* Indicate the transfer is completed.
278	*/
279	complete(&xspi->done);
280	}
281	}
282
283	return IRQ_HANDLED;
284	}
285
ff82c587 JL	286	static int __init xilinx_spi_of_probe(struct of_device *ofdev,
ff82c587 JL	287	const struct of_device_id *match)
ae918c02	288	{
ae918c02 AK	289	struct spi_master *master;
ae918c02 AK	290	struct xilinx_spi *xspi;
ff82c587 JL	291	struct resource r_irq_struct;
	292	struct resource r_mem_struct;
	293
	294	struct resource *r_irq = &r_irq_struct;
	295	struct resource *r_mem = &r_mem_struct;
	296	int rc = 0;
	297	const u32 *prop;
	298	int len;
ae918c02 AK	299
ae918c02 AK	300	/* Get resources(memory, IRQ) associated with the device */
ff82c587	301	master = spi_alloc_master(&ofdev->dev, sizeof(struct xilinx_spi));
ae918c02 AK	302
	303	if (master == NULL) {
	304	return -ENOMEM;
	305	}
	306
ff82c587	307	dev_set_drvdata(&ofdev->dev, master);
ae918c02	308
ff82c587 JL	309	rc = of_address_to_resource(ofdev->node, 0, r_mem);
	310	if (rc) {
	311	dev_warn(&ofdev->dev, "invalid address\n");
ae918c02 AK	312	goto put_master;
	313	}
	314
ff82c587 JL	315	rc = of_irq_to_resource(ofdev->node, 0, r_irq);
	316	if (rc == NO_IRQ) {
	317	dev_warn(&ofdev->dev, "no IRQ found\n");
ae918c02 AK	318	goto put_master;
	319	}
	320
e7db06b5 DB	321	/* the spi->mode bits understood by this driver: */
	322	master->mode_bits = SPI_CPOL \| SPI_CPHA;
	323
ae918c02 AK	324	xspi = spi_master_get_devdata(master);
	325	xspi->bitbang.master = spi_master_get(master);
	326	xspi->bitbang.chipselect = xilinx_spi_chipselect;
	327	xspi->bitbang.setup_transfer = xilinx_spi_setup_transfer;
	328	xspi->bitbang.txrx_bufs = xilinx_spi_txrx_bufs;
	329	xspi->bitbang.master->setup = xilinx_spi_setup;
	330	init_completion(&xspi->done);
	331
ff82c587 JL	332	xspi->irq = r_irq->start;
	333
	334	if (!request_mem_region(r_mem->start,
	335	r_mem->end - r_mem->start + 1, XILINX_SPI_NAME)) {
	336	rc = -ENXIO;
	337	dev_warn(&ofdev->dev, "memory request failure\n");
ae918c02 AK	338	goto put_master;
	339	}
	340
ff82c587	341	xspi->regs = ioremap(r_mem->start, r_mem->end - r_mem->start + 1);
ae918c02	342	if (xspi->regs == NULL) {
ff82c587 JL	343	rc = -ENOMEM;
ff82c587 JL	344	dev_warn(&ofdev->dev, "ioremap failure\n");
1df879e4	345	goto release_mem;
ae918c02	346	}
ff82c587	347	xspi->irq = r_irq->start;
ae918c02	348
ff82c587 JL	349	/* dynamic bus assignment */
ff82c587 JL	350	master->bus_num = -1;
ae918c02	351
ff82c587 JL	352	/* number of slave select bits is required */
	353	prop = of_get_property(ofdev->node, "xlnx,num-ss-bits", &len);
	354	if (!prop \|\| len < sizeof(*prop)) {
	355	dev_warn(&ofdev->dev, "no 'xlnx,num-ss-bits' property\n");
1df879e4	356	goto unmap_io;
ff82c587 JL	357	}
ff82c587 JL	358	master->num_chipselect = *prop;
ae918c02 AK	359
	360	/* SPI controller initializations */
	361	xspi_init_hw(xspi->regs);
	362
	363	/* Register for SPI Interrupt */
ff82c587 JL	364	rc = request_irq(xspi->irq, xilinx_spi_irq, 0, XILINX_SPI_NAME, xspi);
	365	if (rc != 0) {
	366	dev_warn(&ofdev->dev, "irq request failure: %d\n", xspi->irq);
ae918c02	367	goto unmap_io;
ff82c587	368	}
ae918c02	369
ff82c587 JL	370	rc = spi_bitbang_start(&xspi->bitbang);
	371	if (rc != 0) {
	372	dev_err(&ofdev->dev, "spi_bitbang_start FAILED\n");
ae918c02 AK	373	goto free_irq;
	374	}
	375
ff82c587 JL	376	dev_info(&ofdev->dev, "at 0x%08X mapped to 0x%08X, irq=%d\n",
ff82c587 JL	377	(unsigned int)r_mem->start, (u32)xspi->regs, xspi->irq);
ae918c02	378
ff82c587 JL	379	/* Add any subnodes on the SPI bus */
	380	of_register_spi_devices(master, ofdev->node);
	381
	382	return rc;
ae918c02 AK	383
	384	free_irq:
	385	free_irq(xspi->irq, xspi);
	386	unmap_io:
	387	iounmap(xspi->regs);
1df879e4 JL	388	release_mem:
1df879e4 JL	389	release_mem_region(r_mem->start, resource_size(r_mem));
ae918c02 AK	390	put_master:
ae918c02 AK	391	spi_master_put(master);
ff82c587	392	return rc;
ae918c02 AK	393	}
ae918c02 AK	394
ff82c587	395	static int __devexit xilinx_spi_remove(struct of_device *ofdev)
ae918c02 AK	396	{
	397	struct xilinx_spi *xspi;
	398	struct spi_master *master;
1df879e4	399	struct resource r_mem;
ae918c02	400
ff82c587	401	master = platform_get_drvdata(ofdev);
ae918c02 AK	402	xspi = spi_master_get_devdata(master);
	403
	404	spi_bitbang_stop(&xspi->bitbang);
	405	free_irq(xspi->irq, xspi);
	406	iounmap(xspi->regs);
1df879e4 JL	407	if (!of_address_to_resource(ofdev->node, 0, &r_mem))
1df879e4 JL	408	release_mem_region(r_mem.start, resource_size(&r_mem));
ff82c587	409	dev_set_drvdata(&ofdev->dev, 0);
ae918c02 AK	410	spi_master_put(xspi->bitbang.master);
	411
	412	return 0;
	413	}
	414
7e38c3c4 KS	415	/* work with hotplug and coldplug */
	416	MODULE_ALIAS("platform:" XILINX_SPI_NAME);
	417
ff82c587 JL	418	static int __exit xilinx_spi_of_remove(struct of_device *op)
	419	{
	420	return xilinx_spi_remove(op);
	421	}
	422
	423	static struct of_device_id xilinx_spi_of_match[] = {
	424	{ .compatible = "xlnx,xps-spi-2.00.a", },
	425	{ .compatible = "xlnx,xps-spi-2.00.b", },
	426	{}
	427	};
	428
	429	MODULE_DEVICE_TABLE(of, xilinx_spi_of_match);
	430
	431	static struct of_platform_driver xilinx_spi_of_driver = {
	432	.owner = THIS_MODULE,
	433	.name = "xilinx-xps-spi",
	434	.match_table = xilinx_spi_of_match,
	435	.probe = xilinx_spi_of_probe,
	436	.remove = __exit_p(xilinx_spi_of_remove),
ae918c02	437	.driver = {
ff82c587	438	.name = "xilinx-xps-spi",
ae918c02 AK	439	.owner = THIS_MODULE,
	440	},
	441	};
	442
	443	static int __init xilinx_spi_init(void)
	444	{
ff82c587	445	return of_register_platform_driver(&xilinx_spi_of_driver);
ae918c02 AK	446	}
	447	module_init(xilinx_spi_init);
	448
	449	static void __exit xilinx_spi_exit(void)
	450	{
ff82c587	451	of_unregister_platform_driver(&xilinx_spi_of_driver);
ae918c02 AK	452	}
ae918c02 AK	453	module_exit(xilinx_spi_exit);
ae918c02 AK	454	MODULE_AUTHOR("MontaVista Software, Inc. <source@mvista.com>");
	455	MODULE_DESCRIPTION("Xilinx SPI driver");
	456	MODULE_LICENSE("GPL");