]>
Commit | Line | Data |
---|---|---|
1da177e4 LT |
1 | # |
2 | # USB device configuration | |
3 | # | |
4 | ||
900e0621 DD |
5 | config USB_OHCI_BIG_ENDIAN_DESC |
6 | bool | |
7 | ||
8 | config USB_OHCI_BIG_ENDIAN_MMIO | |
9 | bool | |
10 | ||
11 | config USB_OHCI_LITTLE_ENDIAN | |
12 | bool | |
13 | default n if STB03xxx || PPC_MPC52xx | |
14 | default y | |
15 | ||
900e0621 DD |
16 | config USB_EHCI_BIG_ENDIAN_MMIO |
17 | bool | |
18 | ||
19 | config USB_EHCI_BIG_ENDIAN_DESC | |
20 | bool | |
21 | ||
a8edc42a DD |
22 | menuconfig USB_SUPPORT |
23 | bool "USB support" | |
24 | depends on HAS_IOMEM | |
25 | default y | |
26 | ---help--- | |
27 | This option adds core support for Universal Serial Bus (USB). | |
28 | You will also need drivers from the following menu to make use of it. | |
29 | ||
53c6bc24 DD |
30 | if USB_SUPPORT |
31 | ||
32 | config USB_COMMON | |
33 | tristate | |
53c6bc24 | 34 | |
53c6bc24 | 35 | config USB_ARCH_HAS_HCD |
d9ea21a7 | 36 | def_bool y |
53c6bc24 | 37 | |
1da177e4 LT |
38 | # ARM SA1111 chips have a non-PCI based "OHCI-compatible" USB host interface. |
39 | config USB | |
40 | tristate "Support for Host-side USB" | |
41 | depends on USB_ARCH_HAS_HCD | |
badf6d47 | 42 | select USB_COMMON |
a853a3d4 | 43 | select NLS # for UTF-8 strings |
1da177e4 LT |
44 | ---help--- |
45 | Universal Serial Bus (USB) is a specification for a serial bus | |
46 | subsystem which offers higher speeds and more features than the | |
47 | traditional PC serial port. The bus supplies power to peripherals | |
48 | and allows for hot swapping. Up to 127 USB peripherals can be | |
49 | connected to a single USB host in a tree structure. | |
50 | ||
51 | The USB host is the root of the tree, the peripherals are the | |
52 | leaves and the inner nodes are special USB devices called hubs. | |
53 | Most PCs now have USB host ports, used to connect peripherals | |
54 | such as scanners, keyboards, mice, modems, cameras, disks, | |
55 | flash memory, network links, and printers to the PC. | |
56 | ||
57 | Say Y here if your computer has a host-side USB port and you want | |
58 | to use USB devices. You then need to say Y to at least one of the | |
59 | Host Controller Driver (HCD) options below. Choose a USB 1.1 | |
60 | controller, such as "UHCI HCD support" or "OHCI HCD support", | |
61 | and "EHCI HCD (USB 2.0) support" except for older systems that | |
62 | do not have USB 2.0 support. It doesn't normally hurt to select | |
63 | them all if you are not certain. | |
64 | ||
65 | If your system has a device-side USB port, used in the peripheral | |
66 | side of the USB protocol, see the "USB Gadget" framework instead. | |
67 | ||
68 | After choosing your HCD, then select drivers for the USB peripherals | |
69 | you'll be using. You may want to check out the information provided | |
70 | in <file:Documentation/usb/> and especially the links given in | |
71 | <file:Documentation/usb/usb-help.txt>. | |
72 | ||
73 | To compile this driver as a module, choose M here: the | |
74 | module will be called usbcore. | |
75 | ||
25e11ec4 | 76 | if USB |
1da177e4 | 77 | |
25e11ec4 | 78 | source "drivers/usb/core/Kconfig" |
72246da4 | 79 | |
3bea302d SA |
80 | source "drivers/usb/mon/Kconfig" |
81 | ||
470cc415 GKH |
82 | source "drivers/usb/wusbcore/Kconfig" |
83 | ||
1da177e4 LT |
84 | source "drivers/usb/host/Kconfig" |
85 | ||
f1407d5c KM |
86 | source "drivers/usb/renesas_usbhs/Kconfig" |
87 | ||
1da177e4 LT |
88 | source "drivers/usb/class/Kconfig" |
89 | ||
90 | source "drivers/usb/storage/Kconfig" | |
91 | ||
1da177e4 LT |
92 | source "drivers/usb/image/Kconfig" |
93 | ||
96c27377 VM |
94 | source "drivers/usb/usbip/Kconfig" |
95 | ||
25e11ec4 FF |
96 | endif |
97 | ||
df2069ac CY |
98 | source "drivers/usb/mtu3/Kconfig" |
99 | ||
845c071b EG |
100 | source "drivers/usb/musb/Kconfig" |
101 | ||
25e11ec4 FF |
102 | source "drivers/usb/dwc3/Kconfig" |
103 | ||
197ba5f4 PZ |
104 | source "drivers/usb/dwc2/Kconfig" |
105 | ||
25e11ec4 FF |
106 | source "drivers/usb/chipidea/Kconfig" |
107 | ||
7ef077a8 LP |
108 | source "drivers/usb/isp1760/Kconfig" |
109 | ||
1da177e4 | 110 | comment "USB port drivers" |
25e11ec4 FF |
111 | |
112 | if USB | |
1da177e4 LT |
113 | |
114 | config USB_USS720 | |
115 | tristate "USS720 parport driver" | |
25e11ec4 | 116 | depends on PARPORT |
1da177e4 LT |
117 | select PARPORT_NOT_PC |
118 | ---help--- | |
119 | This driver is for USB parallel port adapters that use the Lucent | |
120 | Technologies USS-720 chip. These cables are plugged into your USB | |
121 | port and provide USB compatibility to peripherals designed with | |
122 | parallel port interfaces. | |
123 | ||
124 | The chip has two modes: automatic mode and manual mode. In automatic | |
125 | mode, it looks to the computer like a standard USB printer. Only | |
126 | printers may be connected to the USS-720 in this mode. The generic | |
127 | USB printer driver ("USB Printer support", above) may be used in | |
128 | that mode, and you can say N here if you want to use the chip only | |
129 | in this mode. | |
130 | ||
131 | Manual mode is not limited to printers, any parallel port | |
132 | device should work. This driver utilizes manual mode. | |
133 | Note however that some operations are three orders of magnitude | |
134 | slower than on a PCI/ISA Parallel Port, so timing critical | |
135 | applications might not work. | |
136 | ||
137 | Say Y here if you own an USS-720 USB->Parport cable and intend to | |
138 | connect anything other than a printer to it. | |
139 | ||
140 | To compile this driver as a module, choose M here: the | |
141 | module will be called uss720. | |
142 | ||
143 | source "drivers/usb/serial/Kconfig" | |
144 | ||
145 | source "drivers/usb/misc/Kconfig" | |
146 | ||
147 | source "drivers/usb/atm/Kconfig" | |
148 | ||
25e11ec4 FF |
149 | endif # USB |
150 | ||
151 | source "drivers/usb/phy/Kconfig" | |
152 | ||
1da177e4 LT |
153 | source "drivers/usb/gadget/Kconfig" |
154 | ||
0cfbd328 MS |
155 | config USB_LED_TRIG |
156 | bool "USB LED Triggers" | |
cb9c1cfc PC |
157 | depends on LEDS_CLASS && LEDS_TRIGGERS |
158 | select USB_COMMON | |
0cfbd328 MS |
159 | help |
160 | This option adds LED triggers for USB host and/or gadget activity. | |
161 | ||
162 | Say Y here if you are working on a system with led-class supported | |
163 | LEDs and you want to use them as activity indicators for USB host or | |
164 | gadget. | |
165 | ||
ad764c49 PC |
166 | config USB_ULPI_BUS |
167 | tristate "USB ULPI PHY interface support" | |
cb9c1cfc | 168 | select USB_COMMON |
ad764c49 PC |
169 | help |
170 | UTMI+ Low Pin Interface (ULPI) is specification for a commonly used | |
171 | USB 2.0 PHY interface. The ULPI specification defines a standard set | |
172 | of registers that can be used to detect the vendor and product which | |
173 | allows ULPI to be handled as a bus. This module is the driver for that | |
174 | bus. | |
175 | ||
176 | The ULPI interfaces (the buses) are registered by the drivers for USB | |
177 | controllers which support ULPI register access and have ULPI PHY | |
178 | attached to them. The ULPI PHY drivers themselves are normal PHY | |
179 | drivers. | |
180 | ||
181 | ULPI PHYs provide often functions such as ADP sensing/probing (OTG | |
182 | protocol) and USB charger detection. | |
183 | ||
184 | To compile this driver as a module, choose M here: the module will | |
185 | be called ulpi. | |
186 | ||
04d06ad0 | 187 | endif # USB_SUPPORT |