]>
Commit | Line | Data |
---|---|---|
1da177e4 LT |
1 | /* |
2 | * USB hub driver. | |
3 | * | |
4 | * (C) Copyright 1999 Linus Torvalds | |
5 | * (C) Copyright 1999 Johannes Erdfelt | |
6 | * (C) Copyright 1999 Gregory P. Smith | |
7 | * (C) Copyright 2001 Brad Hards (bhards@bigpond.net.au) | |
8 | * | |
9 | */ | |
10 | ||
1da177e4 LT |
11 | #include <linux/kernel.h> |
12 | #include <linux/errno.h> | |
13 | #include <linux/module.h> | |
14 | #include <linux/moduleparam.h> | |
15 | #include <linux/completion.h> | |
16 | #include <linux/sched.h> | |
17 | #include <linux/list.h> | |
18 | #include <linux/slab.h> | |
1da177e4 LT |
19 | #include <linux/ioctl.h> |
20 | #include <linux/usb.h> | |
21 | #include <linux/usbdevice_fs.h> | |
27729aad | 22 | #include <linux/usb/hcd.h> |
925aa46b | 23 | #include <linux/usb/otg.h> |
93362a87 | 24 | #include <linux/usb/quirks.h> |
32a69589 | 25 | #include <linux/workqueue.h> |
4186ecf8 | 26 | #include <linux/mutex.h> |
b04b3156 | 27 | #include <linux/random.h> |
ad493e5e | 28 | #include <linux/pm_qos.h> |
1da177e4 | 29 | |
1da177e4 LT |
30 | #include <asm/uaccess.h> |
31 | #include <asm/byteorder.h> | |
32 | ||
6e30d7cb | 33 | #include "hub.h" |
026f3fcb | 34 | #include "otg_whitelist.h" |
1da177e4 | 35 | |
e6f30dea ML |
36 | #define USB_VENDOR_GENESYS_LOGIC 0x05e3 |
37 | #define HUB_QUIRK_CHECK_PORT_AUTOSUSPEND 0x01 | |
38 | ||
fa286188 | 39 | /* Protect struct usb_device->state and ->children members |
9ad3d6cc | 40 | * Note: Both are also protected by ->dev.sem, except that ->state can |
1da177e4 LT |
41 | * change to USB_STATE_NOTATTACHED even when the semaphore isn't held. */ |
42 | static DEFINE_SPINLOCK(device_state_lock); | |
43 | ||
32a69589 PM |
44 | /* workqueue to process hub events */ |
45 | static struct workqueue_struct *hub_wq; | |
46 | static void hub_event(struct work_struct *work); | |
1da177e4 | 47 | |
d8521afe DW |
48 | /* synchronize hub-port add/remove and peering operations */ |
49 | DEFINE_MUTEX(usb_port_peer_mutex); | |
50 | ||
1da177e4 | 51 | /* cycle leds on hubs that aren't blinking for attention */ |
90ab5ee9 | 52 | static bool blinkenlights = 0; |
166b8639 CM |
53 | module_param(blinkenlights, bool, S_IRUGO); |
54 | MODULE_PARM_DESC(blinkenlights, "true to cycle leds on hubs"); | |
1da177e4 | 55 | |
fd7c519d JK |
56 | /* |
57 | * Device SATA8000 FW1.0 from DATAST0R Technology Corp requires about | |
58 | * 10 seconds to send reply for the initial 64-byte descriptor request. | |
59 | */ | |
60 | /* define initial 64-byte descriptor request timeout in milliseconds */ | |
61 | static int initial_descriptor_timeout = USB_CTRL_GET_TIMEOUT; | |
62 | module_param(initial_descriptor_timeout, int, S_IRUGO|S_IWUSR); | |
b9cef6c3 WF |
63 | MODULE_PARM_DESC(initial_descriptor_timeout, |
64 | "initial 64-byte descriptor request timeout in milliseconds " | |
65 | "(default 5000 - 5.0 seconds)"); | |
fd7c519d | 66 | |
1da177e4 LT |
67 | /* |
68 | * As of 2.6.10 we introduce a new USB device initialization scheme which | |
69 | * closely resembles the way Windows works. Hopefully it will be compatible | |
70 | * with a wider range of devices than the old scheme. However some previously | |
71 | * working devices may start giving rise to "device not accepting address" | |
72 | * errors; if that happens the user can try the old scheme by adjusting the | |
73 | * following module parameters. | |
74 | * | |
75 | * For maximum flexibility there are two boolean parameters to control the | |
76 | * hub driver's behavior. On the first initialization attempt, if the | |
77 | * "old_scheme_first" parameter is set then the old scheme will be used, | |
78 | * otherwise the new scheme is used. If that fails and "use_both_schemes" | |
79 | * is set, then the driver will make another attempt, using the other scheme. | |
80 | */ | |
90ab5ee9 | 81 | static bool old_scheme_first = 0; |
1da177e4 LT |
82 | module_param(old_scheme_first, bool, S_IRUGO | S_IWUSR); |
83 | MODULE_PARM_DESC(old_scheme_first, | |
84 | "start with the old device initialization scheme"); | |
85 | ||
90ab5ee9 | 86 | static bool use_both_schemes = 1; |
1da177e4 LT |
87 | module_param(use_both_schemes, bool, S_IRUGO | S_IWUSR); |
88 | MODULE_PARM_DESC(use_both_schemes, | |
89 | "try the other device initialization scheme if the " | |
90 | "first one fails"); | |
91 | ||
32fe0198 AS |
92 | /* Mutual exclusion for EHCI CF initialization. This interferes with |
93 | * port reset on some companion controllers. | |
94 | */ | |
95 | DECLARE_RWSEM(ehci_cf_port_reset_rwsem); | |
96 | EXPORT_SYMBOL_GPL(ehci_cf_port_reset_rwsem); | |
97 | ||
ad493e5e | 98 | #define HUB_DEBOUNCE_TIMEOUT 2000 |
948fea37 AS |
99 | #define HUB_DEBOUNCE_STEP 25 |
100 | #define HUB_DEBOUNCE_STABLE 100 | |
101 | ||
32a69589 | 102 | static void hub_release(struct kref *kref); |
742120c6 ML |
103 | static int usb_reset_and_verify_device(struct usb_device *udev); |
104 | ||
131dec34 | 105 | static inline char *portspeed(struct usb_hub *hub, int portstatus) |
1da177e4 | 106 | { |
131dec34 SS |
107 | if (hub_is_superspeed(hub->hdev)) |
108 | return "5.0 Gb/s"; | |
288ead45 | 109 | if (portstatus & USB_PORT_STAT_HIGH_SPEED) |
469271f8 | 110 | return "480 Mb/s"; |
288ead45 | 111 | else if (portstatus & USB_PORT_STAT_LOW_SPEED) |
1da177e4 LT |
112 | return "1.5 Mb/s"; |
113 | else | |
114 | return "12 Mb/s"; | |
115 | } | |
1da177e4 LT |
116 | |
117 | /* Note that hdev or one of its children must be locked! */ | |
ad493e5e | 118 | struct usb_hub *usb_hub_to_struct_hub(struct usb_device *hdev) |
1da177e4 | 119 | { |
ff823c79 | 120 | if (!hdev || !hdev->actconfig || !hdev->maxchild) |
25118084 | 121 | return NULL; |
1da177e4 LT |
122 | return usb_get_intfdata(hdev->actconfig->interface[0]); |
123 | } | |
124 | ||
2d2a3167 | 125 | int usb_device_supports_lpm(struct usb_device *udev) |
d9b2099c | 126 | { |
ad87e032 AS |
127 | /* Some devices have trouble with LPM */ |
128 | if (udev->quirks & USB_QUIRK_NO_LPM) | |
129 | return 0; | |
130 | ||
d9b2099c SS |
131 | /* USB 2.1 (and greater) devices indicate LPM support through |
132 | * their USB 2.0 Extended Capabilities BOS descriptor. | |
133 | */ | |
a8425292 | 134 | if (udev->speed == USB_SPEED_HIGH || udev->speed == USB_SPEED_FULL) { |
d9b2099c SS |
135 | if (udev->bos->ext_cap && |
136 | (USB_LPM_SUPPORT & | |
137 | le32_to_cpu(udev->bos->ext_cap->bmAttributes))) | |
138 | return 1; | |
139 | return 0; | |
140 | } | |
51e0a012 | 141 | |
25cd2882 SS |
142 | /* |
143 | * According to the USB 3.0 spec, all USB 3.0 devices must support LPM. | |
144 | * However, there are some that don't, and they set the U1/U2 exit | |
145 | * latencies to zero. | |
51e0a012 SS |
146 | */ |
147 | if (!udev->bos->ss_cap) { | |
25cd2882 | 148 | dev_info(&udev->dev, "No LPM exit latency info found, disabling LPM.\n"); |
51e0a012 SS |
149 | return 0; |
150 | } | |
51e0a012 | 151 | |
25cd2882 SS |
152 | if (udev->bos->ss_cap->bU1devExitLat == 0 && |
153 | udev->bos->ss_cap->bU2DevExitLat == 0) { | |
154 | if (udev->parent) | |
155 | dev_info(&udev->dev, "LPM exit latency is zeroed, disabling LPM.\n"); | |
156 | else | |
157 | dev_info(&udev->dev, "We don't know the algorithms for LPM for this host, disabling LPM.\n"); | |
51e0a012 SS |
158 | return 0; |
159 | } | |
51e0a012 | 160 | |
25cd2882 SS |
161 | if (!udev->parent || udev->parent->lpm_capable) |
162 | return 1; | |
d9b2099c SS |
163 | return 0; |
164 | } | |
165 | ||
51e0a012 SS |
166 | /* |
167 | * Set the Maximum Exit Latency (MEL) for the host to initiate a transition from | |
168 | * either U1 or U2. | |
169 | */ | |
170 | static void usb_set_lpm_mel(struct usb_device *udev, | |
171 | struct usb3_lpm_parameters *udev_lpm_params, | |
172 | unsigned int udev_exit_latency, | |
173 | struct usb_hub *hub, | |
174 | struct usb3_lpm_parameters *hub_lpm_params, | |
175 | unsigned int hub_exit_latency) | |
176 | { | |
177 | unsigned int total_mel; | |
178 | unsigned int device_mel; | |
179 | unsigned int hub_mel; | |
180 | ||
181 | /* | |
182 | * Calculate the time it takes to transition all links from the roothub | |
183 | * to the parent hub into U0. The parent hub must then decode the | |
184 | * packet (hub header decode latency) to figure out which port it was | |
185 | * bound for. | |
186 | * | |
187 | * The Hub Header decode latency is expressed in 0.1us intervals (0x1 | |
188 | * means 0.1us). Multiply that by 100 to get nanoseconds. | |
189 | */ | |
190 | total_mel = hub_lpm_params->mel + | |
191 | (hub->descriptor->u.ss.bHubHdrDecLat * 100); | |
192 | ||
193 | /* | |
194 | * How long will it take to transition the downstream hub's port into | |
195 | * U0? The greater of either the hub exit latency or the device exit | |
196 | * latency. | |
197 | * | |
198 | * The BOS U1/U2 exit latencies are expressed in 1us intervals. | |
199 | * Multiply that by 1000 to get nanoseconds. | |
200 | */ | |
201 | device_mel = udev_exit_latency * 1000; | |
202 | hub_mel = hub_exit_latency * 1000; | |
203 | if (device_mel > hub_mel) | |
204 | total_mel += device_mel; | |
205 | else | |
206 | total_mel += hub_mel; | |
207 | ||
208 | udev_lpm_params->mel = total_mel; | |
209 | } | |
210 | ||
211 | /* | |
212 | * Set the maximum Device to Host Exit Latency (PEL) for the device to initiate | |
213 | * a transition from either U1 or U2. | |
214 | */ | |
215 | static void usb_set_lpm_pel(struct usb_device *udev, | |
216 | struct usb3_lpm_parameters *udev_lpm_params, | |
217 | unsigned int udev_exit_latency, | |
218 | struct usb_hub *hub, | |
219 | struct usb3_lpm_parameters *hub_lpm_params, | |
220 | unsigned int hub_exit_latency, | |
221 | unsigned int port_to_port_exit_latency) | |
222 | { | |
223 | unsigned int first_link_pel; | |
224 | unsigned int hub_pel; | |
225 | ||
226 | /* | |
227 | * First, the device sends an LFPS to transition the link between the | |
228 | * device and the parent hub into U0. The exit latency is the bigger of | |
229 | * the device exit latency or the hub exit latency. | |
230 | */ | |
231 | if (udev_exit_latency > hub_exit_latency) | |
232 | first_link_pel = udev_exit_latency * 1000; | |
233 | else | |
234 | first_link_pel = hub_exit_latency * 1000; | |
235 | ||
236 | /* | |
237 | * When the hub starts to receive the LFPS, there is a slight delay for | |
238 | * it to figure out that one of the ports is sending an LFPS. Then it | |
239 | * will forward the LFPS to its upstream link. The exit latency is the | |
240 | * delay, plus the PEL that we calculated for this hub. | |
241 | */ | |
242 | hub_pel = port_to_port_exit_latency * 1000 + hub_lpm_params->pel; | |
243 | ||
244 | /* | |
245 | * According to figure C-7 in the USB 3.0 spec, the PEL for this device | |
246 | * is the greater of the two exit latencies. | |
247 | */ | |
248 | if (first_link_pel > hub_pel) | |
249 | udev_lpm_params->pel = first_link_pel; | |
250 | else | |
251 | udev_lpm_params->pel = hub_pel; | |
252 | } | |
253 | ||
254 | /* | |
255 | * Set the System Exit Latency (SEL) to indicate the total worst-case time from | |
256 | * when a device initiates a transition to U0, until when it will receive the | |
257 | * first packet from the host controller. | |
258 | * | |
259 | * Section C.1.5.1 describes the four components to this: | |
260 | * - t1: device PEL | |
261 | * - t2: time for the ERDY to make it from the device to the host. | |
262 | * - t3: a host-specific delay to process the ERDY. | |
263 | * - t4: time for the packet to make it from the host to the device. | |
264 | * | |
265 | * t3 is specific to both the xHCI host and the platform the host is integrated | |
266 | * into. The Intel HW folks have said it's negligible, FIXME if a different | |
267 | * vendor says otherwise. | |
268 | */ | |
269 | static void usb_set_lpm_sel(struct usb_device *udev, | |
270 | struct usb3_lpm_parameters *udev_lpm_params) | |
271 | { | |
272 | struct usb_device *parent; | |
273 | unsigned int num_hubs; | |
274 | unsigned int total_sel; | |
275 | ||
276 | /* t1 = device PEL */ | |
277 | total_sel = udev_lpm_params->pel; | |
278 | /* How many external hubs are in between the device & the root port. */ | |
279 | for (parent = udev->parent, num_hubs = 0; parent->parent; | |
280 | parent = parent->parent) | |
281 | num_hubs++; | |
282 | /* t2 = 2.1us + 250ns * (num_hubs - 1) */ | |
283 | if (num_hubs > 0) | |
284 | total_sel += 2100 + 250 * (num_hubs - 1); | |
285 | ||
286 | /* t4 = 250ns * num_hubs */ | |
287 | total_sel += 250 * num_hubs; | |
288 | ||
289 | udev_lpm_params->sel = total_sel; | |
290 | } | |
291 | ||
292 | static void usb_set_lpm_parameters(struct usb_device *udev) | |
293 | { | |
294 | struct usb_hub *hub; | |
295 | unsigned int port_to_port_delay; | |
296 | unsigned int udev_u1_del; | |
297 | unsigned int udev_u2_del; | |
298 | unsigned int hub_u1_del; | |
299 | unsigned int hub_u2_del; | |
300 | ||
301 | if (!udev->lpm_capable || udev->speed != USB_SPEED_SUPER) | |
302 | return; | |
303 | ||
ad493e5e | 304 | hub = usb_hub_to_struct_hub(udev->parent); |
51e0a012 SS |
305 | /* It doesn't take time to transition the roothub into U0, since it |
306 | * doesn't have an upstream link. | |
307 | */ | |
308 | if (!hub) | |
309 | return; | |
310 | ||
311 | udev_u1_del = udev->bos->ss_cap->bU1devExitLat; | |
4d967995 | 312 | udev_u2_del = le16_to_cpu(udev->bos->ss_cap->bU2DevExitLat); |
51e0a012 | 313 | hub_u1_del = udev->parent->bos->ss_cap->bU1devExitLat; |
4d967995 | 314 | hub_u2_del = le16_to_cpu(udev->parent->bos->ss_cap->bU2DevExitLat); |
51e0a012 SS |
315 | |
316 | usb_set_lpm_mel(udev, &udev->u1_params, udev_u1_del, | |
317 | hub, &udev->parent->u1_params, hub_u1_del); | |
318 | ||
319 | usb_set_lpm_mel(udev, &udev->u2_params, udev_u2_del, | |
320 | hub, &udev->parent->u2_params, hub_u2_del); | |
321 | ||
322 | /* | |
323 | * Appendix C, section C.2.2.2, says that there is a slight delay from | |
324 | * when the parent hub notices the downstream port is trying to | |
325 | * transition to U0 to when the hub initiates a U0 transition on its | |
326 | * upstream port. The section says the delays are tPort2PortU1EL and | |
327 | * tPort2PortU2EL, but it doesn't define what they are. | |
328 | * | |
329 | * The hub chapter, sections 10.4.2.4 and 10.4.2.5 seem to be talking | |
330 | * about the same delays. Use the maximum delay calculations from those | |
331 | * sections. For U1, it's tHubPort2PortExitLat, which is 1us max. For | |
332 | * U2, it's tHubPort2PortExitLat + U2DevExitLat - U1DevExitLat. I | |
333 | * assume the device exit latencies they are talking about are the hub | |
334 | * exit latencies. | |
335 | * | |
336 | * What do we do if the U2 exit latency is less than the U1 exit | |
337 | * latency? It's possible, although not likely... | |
338 | */ | |
339 | port_to_port_delay = 1; | |
340 | ||
341 | usb_set_lpm_pel(udev, &udev->u1_params, udev_u1_del, | |
342 | hub, &udev->parent->u1_params, hub_u1_del, | |
343 | port_to_port_delay); | |
344 | ||
345 | if (hub_u2_del > hub_u1_del) | |
346 | port_to_port_delay = 1 + hub_u2_del - hub_u1_del; | |
347 | else | |
348 | port_to_port_delay = 1 + hub_u1_del; | |
349 | ||
350 | usb_set_lpm_pel(udev, &udev->u2_params, udev_u2_del, | |
351 | hub, &udev->parent->u2_params, hub_u2_del, | |
352 | port_to_port_delay); | |
353 | ||
354 | /* Now that we've got PEL, calculate SEL. */ | |
355 | usb_set_lpm_sel(udev, &udev->u1_params); | |
356 | usb_set_lpm_sel(udev, &udev->u2_params); | |
357 | } | |
358 | ||
1da177e4 | 359 | /* USB 2.0 spec Section 11.24.4.5 */ |
dbe79bbe | 360 | static int get_hub_descriptor(struct usb_device *hdev, void *data) |
1da177e4 | 361 | { |
dbe79bbe JY |
362 | int i, ret, size; |
363 | unsigned dtype; | |
364 | ||
365 | if (hub_is_superspeed(hdev)) { | |
366 | dtype = USB_DT_SS_HUB; | |
367 | size = USB_DT_SS_HUB_SIZE; | |
368 | } else { | |
369 | dtype = USB_DT_HUB; | |
370 | size = sizeof(struct usb_hub_descriptor); | |
371 | } | |
1da177e4 LT |
372 | |
373 | for (i = 0; i < 3; i++) { | |
374 | ret = usb_control_msg(hdev, usb_rcvctrlpipe(hdev, 0), | |
375 | USB_REQ_GET_DESCRIPTOR, USB_DIR_IN | USB_RT_HUB, | |
dbe79bbe | 376 | dtype << 8, 0, data, size, |
1da177e4 LT |
377 | USB_CTRL_GET_TIMEOUT); |
378 | if (ret >= (USB_DT_HUB_NONVAR_SIZE + 2)) | |
379 | return ret; | |
380 | } | |
381 | return -EINVAL; | |
382 | } | |
383 | ||
384 | /* | |
385 | * USB 2.0 spec Section 11.24.2.1 | |
386 | */ | |
387 | static int clear_hub_feature(struct usb_device *hdev, int feature) | |
388 | { | |
389 | return usb_control_msg(hdev, usb_sndctrlpipe(hdev, 0), | |
390 | USB_REQ_CLEAR_FEATURE, USB_RT_HUB, feature, 0, NULL, 0, 1000); | |
391 | } | |
392 | ||
393 | /* | |
394 | * USB 2.0 spec Section 11.24.2.2 | |
395 | */ | |
ad493e5e | 396 | int usb_clear_port_feature(struct usb_device *hdev, int port1, int feature) |
1da177e4 LT |
397 | { |
398 | return usb_control_msg(hdev, usb_sndctrlpipe(hdev, 0), | |
399 | USB_REQ_CLEAR_FEATURE, USB_RT_PORT, feature, port1, | |
400 | NULL, 0, 1000); | |
401 | } | |
402 | ||
403 | /* | |
404 | * USB 2.0 spec Section 11.24.2.13 | |
405 | */ | |
406 | static int set_port_feature(struct usb_device *hdev, int port1, int feature) | |
407 | { | |
408 | return usb_control_msg(hdev, usb_sndctrlpipe(hdev, 0), | |
409 | USB_REQ_SET_FEATURE, USB_RT_PORT, feature, port1, | |
410 | NULL, 0, 1000); | |
411 | } | |
412 | ||
d99f6b41 DW |
413 | static char *to_led_name(int selector) |
414 | { | |
415 | switch (selector) { | |
416 | case HUB_LED_AMBER: | |
417 | return "amber"; | |
418 | case HUB_LED_GREEN: | |
419 | return "green"; | |
420 | case HUB_LED_OFF: | |
421 | return "off"; | |
422 | case HUB_LED_AUTO: | |
423 | return "auto"; | |
424 | default: | |
425 | return "??"; | |
426 | } | |
427 | } | |
428 | ||
1da177e4 LT |
429 | /* |
430 | * USB 2.0 spec Section 11.24.2.7.1.10 and table 11-7 | |
431 | * for info about using port indicators | |
432 | */ | |
d99f6b41 | 433 | static void set_port_led(struct usb_hub *hub, int port1, int selector) |
1da177e4 | 434 | { |
d99f6b41 DW |
435 | struct usb_port *port_dev = hub->ports[port1 - 1]; |
436 | int status; | |
437 | ||
438 | status = set_port_feature(hub->hdev, (selector << 8) | port1, | |
1da177e4 | 439 | USB_PORT_FEAT_INDICATOR); |
d99f6b41 DW |
440 | dev_dbg(&port_dev->dev, "indicator %s status %d\n", |
441 | to_led_name(selector), status); | |
1da177e4 LT |
442 | } |
443 | ||
444 | #define LED_CYCLE_PERIOD ((2*HZ)/3) | |
445 | ||
166b8639 | 446 | static void led_work(struct work_struct *work) |
1da177e4 | 447 | { |
c4028958 DH |
448 | struct usb_hub *hub = |
449 | container_of(work, struct usb_hub, leds.work); | |
1da177e4 LT |
450 | struct usb_device *hdev = hub->hdev; |
451 | unsigned i; | |
452 | unsigned changed = 0; | |
453 | int cursor = -1; | |
454 | ||
455 | if (hdev->state != USB_STATE_CONFIGURED || hub->quiescing) | |
456 | return; | |
457 | ||
3bbc47d8 | 458 | for (i = 0; i < hdev->maxchild; i++) { |
1da177e4 LT |
459 | unsigned selector, mode; |
460 | ||
461 | /* 30%-50% duty cycle */ | |
462 | ||
463 | switch (hub->indicator[i]) { | |
464 | /* cycle marker */ | |
465 | case INDICATOR_CYCLE: | |
466 | cursor = i; | |
467 | selector = HUB_LED_AUTO; | |
468 | mode = INDICATOR_AUTO; | |
469 | break; | |
470 | /* blinking green = sw attention */ | |
471 | case INDICATOR_GREEN_BLINK: | |
472 | selector = HUB_LED_GREEN; | |
473 | mode = INDICATOR_GREEN_BLINK_OFF; | |
474 | break; | |
475 | case INDICATOR_GREEN_BLINK_OFF: | |
476 | selector = HUB_LED_OFF; | |
477 | mode = INDICATOR_GREEN_BLINK; | |
478 | break; | |
479 | /* blinking amber = hw attention */ | |
480 | case INDICATOR_AMBER_BLINK: | |
481 | selector = HUB_LED_AMBER; | |
482 | mode = INDICATOR_AMBER_BLINK_OFF; | |
483 | break; | |
484 | case INDICATOR_AMBER_BLINK_OFF: | |
485 | selector = HUB_LED_OFF; | |
486 | mode = INDICATOR_AMBER_BLINK; | |
487 | break; | |
488 | /* blink green/amber = reserved */ | |
489 | case INDICATOR_ALT_BLINK: | |
490 | selector = HUB_LED_GREEN; | |
491 | mode = INDICATOR_ALT_BLINK_OFF; | |
492 | break; | |
493 | case INDICATOR_ALT_BLINK_OFF: | |
494 | selector = HUB_LED_AMBER; | |
495 | mode = INDICATOR_ALT_BLINK; | |
496 | break; | |
497 | default: | |
498 | continue; | |
499 | } | |
500 | if (selector != HUB_LED_AUTO) | |
501 | changed = 1; | |
502 | set_port_led(hub, i + 1, selector); | |
503 | hub->indicator[i] = mode; | |
504 | } | |
505 | if (!changed && blinkenlights) { | |
506 | cursor++; | |
3bbc47d8 | 507 | cursor %= hdev->maxchild; |
1da177e4 LT |
508 | set_port_led(hub, cursor + 1, HUB_LED_GREEN); |
509 | hub->indicator[cursor] = INDICATOR_CYCLE; | |
510 | changed++; | |
511 | } | |
512 | if (changed) | |
22f6a0f0 SD |
513 | queue_delayed_work(system_power_efficient_wq, |
514 | &hub->leds, LED_CYCLE_PERIOD); | |
1da177e4 LT |
515 | } |
516 | ||
517 | /* use a short timeout for hub/port status fetches */ | |
518 | #define USB_STS_TIMEOUT 1000 | |
519 | #define USB_STS_RETRIES 5 | |
520 | ||
521 | /* | |
522 | * USB 2.0 spec Section 11.24.2.6 | |
523 | */ | |
524 | static int get_hub_status(struct usb_device *hdev, | |
525 | struct usb_hub_status *data) | |
526 | { | |
527 | int i, status = -ETIMEDOUT; | |
528 | ||
3824c1dd LP |
529 | for (i = 0; i < USB_STS_RETRIES && |
530 | (status == -ETIMEDOUT || status == -EPIPE); i++) { | |
1da177e4 LT |
531 | status = usb_control_msg(hdev, usb_rcvctrlpipe(hdev, 0), |
532 | USB_REQ_GET_STATUS, USB_DIR_IN | USB_RT_HUB, 0, 0, | |
533 | data, sizeof(*data), USB_STS_TIMEOUT); | |
534 | } | |
535 | return status; | |
536 | } | |
537 | ||
538 | /* | |
539 | * USB 2.0 spec Section 11.24.2.7 | |
540 | */ | |
541 | static int get_port_status(struct usb_device *hdev, int port1, | |
542 | struct usb_port_status *data) | |
543 | { | |
544 | int i, status = -ETIMEDOUT; | |
545 | ||
3824c1dd LP |
546 | for (i = 0; i < USB_STS_RETRIES && |
547 | (status == -ETIMEDOUT || status == -EPIPE); i++) { | |
1da177e4 LT |
548 | status = usb_control_msg(hdev, usb_rcvctrlpipe(hdev, 0), |
549 | USB_REQ_GET_STATUS, USB_DIR_IN | USB_RT_PORT, 0, port1, | |
550 | data, sizeof(*data), USB_STS_TIMEOUT); | |
551 | } | |
552 | return status; | |
553 | } | |
554 | ||
3eb14915 AS |
555 | static int hub_port_status(struct usb_hub *hub, int port1, |
556 | u16 *status, u16 *change) | |
557 | { | |
558 | int ret; | |
559 | ||
560 | mutex_lock(&hub->status_mutex); | |
561 | ret = get_port_status(hub->hdev, port1, &hub->status->port); | |
562 | if (ret < 4) { | |
e9e88fb7 AS |
563 | if (ret != -ENODEV) |
564 | dev_err(hub->intfdev, | |
565 | "%s failed (err = %d)\n", __func__, ret); | |
3eb14915 AS |
566 | if (ret >= 0) |
567 | ret = -EIO; | |
568 | } else { | |
569 | *status = le16_to_cpu(hub->status->port.wPortStatus); | |
570 | *change = le16_to_cpu(hub->status->port.wPortChange); | |
dbe79bbe | 571 | |
3eb14915 AS |
572 | ret = 0; |
573 | } | |
574 | mutex_unlock(&hub->status_mutex); | |
575 | return ret; | |
576 | } | |
577 | ||
32a69589 | 578 | static void kick_hub_wq(struct usb_hub *hub) |
1da177e4 | 579 | { |
32a69589 | 580 | struct usb_interface *intf; |
1da177e4 | 581 | |
32a69589 PM |
582 | if (hub->disconnected || work_pending(&hub->events)) |
583 | return; | |
8e4ceb38 | 584 | |
32a69589 PM |
585 | /* |
586 | * Suppress autosuspend until the event is proceed. | |
587 | * | |
588 | * Be careful and make sure that the symmetric operation is | |
589 | * always called. We are here only when there is no pending | |
590 | * work for this hub. Therefore put the interface either when | |
591 | * the new work is called or when it is canceled. | |
592 | */ | |
593 | intf = to_usb_interface(hub->intfdev); | |
594 | usb_autopm_get_interface_no_resume(intf); | |
595 | kref_get(&hub->kref); | |
596 | ||
597 | if (queue_work(hub_wq, &hub->events)) | |
598 | return; | |
599 | ||
600 | /* the work has already been scheduled */ | |
601 | usb_autopm_put_interface_async(intf); | |
602 | kref_put(&hub->kref, hub_release); | |
1da177e4 LT |
603 | } |
604 | ||
59d48b3f | 605 | void usb_kick_hub_wq(struct usb_device *hdev) |
1da177e4 | 606 | { |
ad493e5e | 607 | struct usb_hub *hub = usb_hub_to_struct_hub(hdev); |
25118084 AS |
608 | |
609 | if (hub) | |
32a69589 | 610 | kick_hub_wq(hub); |
1da177e4 LT |
611 | } |
612 | ||
4ee823b8 SS |
613 | /* |
614 | * Let the USB core know that a USB 3.0 device has sent a Function Wake Device | |
615 | * Notification, which indicates it had initiated remote wakeup. | |
616 | * | |
617 | * USB 3.0 hubs do not report the port link state change from U3 to U0 when the | |
618 | * device initiates resume, so the USB core will not receive notice of the | |
619 | * resume through the normal hub interrupt URB. | |
620 | */ | |
621 | void usb_wakeup_notification(struct usb_device *hdev, | |
622 | unsigned int portnum) | |
623 | { | |
624 | struct usb_hub *hub; | |
625 | ||
626 | if (!hdev) | |
627 | return; | |
628 | ||
ad493e5e | 629 | hub = usb_hub_to_struct_hub(hdev); |
4ee823b8 SS |
630 | if (hub) { |
631 | set_bit(portnum, hub->wakeup_bits); | |
32a69589 | 632 | kick_hub_wq(hub); |
4ee823b8 SS |
633 | } |
634 | } | |
635 | EXPORT_SYMBOL_GPL(usb_wakeup_notification); | |
1da177e4 LT |
636 | |
637 | /* completion function, fires on port status changes and various faults */ | |
7d12e780 | 638 | static void hub_irq(struct urb *urb) |
1da177e4 | 639 | { |
ec17cf1c | 640 | struct usb_hub *hub = urb->context; |
e015268d | 641 | int status = urb->status; |
71d2718f | 642 | unsigned i; |
1da177e4 LT |
643 | unsigned long bits; |
644 | ||
e015268d | 645 | switch (status) { |
1da177e4 LT |
646 | case -ENOENT: /* synchronous unlink */ |
647 | case -ECONNRESET: /* async unlink */ | |
648 | case -ESHUTDOWN: /* hardware going away */ | |
649 | return; | |
650 | ||
651 | default: /* presumably an error */ | |
652 | /* Cause a hub reset after 10 consecutive errors */ | |
166b8639 | 653 | dev_dbg(hub->intfdev, "transfer --> %d\n", status); |
1da177e4 LT |
654 | if ((++hub->nerrors < 10) || hub->error) |
655 | goto resubmit; | |
e015268d | 656 | hub->error = status; |
1da177e4 | 657 | /* FALL THROUGH */ |
ec17cf1c | 658 | |
37ebb549 | 659 | /* let hub_wq handle things */ |
1da177e4 LT |
660 | case 0: /* we got data: port status changed */ |
661 | bits = 0; | |
662 | for (i = 0; i < urb->actual_length; ++i) | |
663 | bits |= ((unsigned long) ((*hub->buffer)[i])) | |
664 | << (i*8); | |
665 | hub->event_bits[0] = bits; | |
666 | break; | |
667 | } | |
668 | ||
669 | hub->nerrors = 0; | |
670 | ||
37ebb549 | 671 | /* Something happened, let hub_wq figure it out */ |
32a69589 | 672 | kick_hub_wq(hub); |
1da177e4 LT |
673 | |
674 | resubmit: | |
675 | if (hub->quiescing) | |
676 | return; | |
677 | ||
088a3dae KB |
678 | status = usb_submit_urb(hub->urb, GFP_ATOMIC); |
679 | if (status != 0 && status != -ENODEV && status != -EPERM) | |
166b8639 | 680 | dev_err(hub->intfdev, "resubmit --> %d\n", status); |
1da177e4 LT |
681 | } |
682 | ||
683 | /* USB 2.0 spec Section 11.24.2.3 */ | |
684 | static inline int | |
166b8639 | 685 | hub_clear_tt_buffer(struct usb_device *hdev, u16 devinfo, u16 tt) |
1da177e4 | 686 | { |
2c7b871b WG |
687 | /* Need to clear both directions for control ep */ |
688 | if (((devinfo >> 11) & USB_ENDPOINT_XFERTYPE_MASK) == | |
689 | USB_ENDPOINT_XFER_CONTROL) { | |
690 | int status = usb_control_msg(hdev, usb_sndctrlpipe(hdev, 0), | |
691 | HUB_CLEAR_TT_BUFFER, USB_RT_PORT, | |
692 | devinfo ^ 0x8000, tt, NULL, 0, 1000); | |
693 | if (status) | |
694 | return status; | |
695 | } | |
c2f6595f | 696 | return usb_control_msg(hdev, usb_sndctrlpipe(hdev, 0), |
1da177e4 LT |
697 | HUB_CLEAR_TT_BUFFER, USB_RT_PORT, devinfo, |
698 | tt, NULL, 0, 1000); | |
699 | } | |
700 | ||
701 | /* | |
37ebb549 | 702 | * enumeration blocks hub_wq for a long time. we use keventd instead, since |
1da177e4 LT |
703 | * long blocking there is the exception, not the rule. accordingly, HCDs |
704 | * talking to TTs must queue control transfers (not just bulk and iso), so | |
705 | * both can talk to the same hub concurrently. | |
706 | */ | |
cb88a1b8 | 707 | static void hub_tt_work(struct work_struct *work) |
1da177e4 | 708 | { |
c4028958 | 709 | struct usb_hub *hub = |
cb88a1b8 | 710 | container_of(work, struct usb_hub, tt.clear_work); |
1da177e4 LT |
711 | unsigned long flags; |
712 | ||
166b8639 | 713 | spin_lock_irqsave(&hub->tt.lock, flags); |
3b6054da | 714 | while (!list_empty(&hub->tt.clear_list)) { |
d0f830d3 | 715 | struct list_head *next; |
1da177e4 LT |
716 | struct usb_tt_clear *clear; |
717 | struct usb_device *hdev = hub->hdev; | |
cb88a1b8 | 718 | const struct hc_driver *drv; |
1da177e4 LT |
719 | int status; |
720 | ||
d0f830d3 | 721 | next = hub->tt.clear_list.next; |
166b8639 CM |
722 | clear = list_entry(next, struct usb_tt_clear, clear_list); |
723 | list_del(&clear->clear_list); | |
1da177e4 LT |
724 | |
725 | /* drop lock so HCD can concurrently report other TT errors */ | |
166b8639 CM |
726 | spin_unlock_irqrestore(&hub->tt.lock, flags); |
727 | status = hub_clear_tt_buffer(hdev, clear->devinfo, clear->tt); | |
e9e88fb7 | 728 | if (status && status != -ENODEV) |
166b8639 | 729 | dev_err(&hdev->dev, |
1da177e4 LT |
730 | "clear tt %d (%04x) error %d\n", |
731 | clear->tt, clear->devinfo, status); | |
cb88a1b8 AS |
732 | |
733 | /* Tell the HCD, even if the operation failed */ | |
734 | drv = clear->hcd->driver; | |
735 | if (drv->clear_tt_buffer_complete) | |
736 | (drv->clear_tt_buffer_complete)(clear->hcd, clear->ep); | |
737 | ||
1bc3c9e1 | 738 | kfree(clear); |
cb88a1b8 | 739 | spin_lock_irqsave(&hub->tt.lock, flags); |
1da177e4 | 740 | } |
166b8639 | 741 | spin_unlock_irqrestore(&hub->tt.lock, flags); |
1da177e4 LT |
742 | } |
743 | ||
971fcd49 LT |
744 | /** |
745 | * usb_hub_set_port_power - control hub port's power state | |
41341261 MN |
746 | * @hdev: USB device belonging to the usb hub |
747 | * @hub: target hub | |
971fcd49 LT |
748 | * @port1: port index |
749 | * @set: expected status | |
750 | * | |
751 | * call this function to control port's power via setting or | |
752 | * clearing the port's PORT_POWER feature. | |
626f090c YB |
753 | * |
754 | * Return: 0 if successful. A negative error code otherwise. | |
971fcd49 | 755 | */ |
41341261 MN |
756 | int usb_hub_set_port_power(struct usb_device *hdev, struct usb_hub *hub, |
757 | int port1, bool set) | |
971fcd49 LT |
758 | { |
759 | int ret; | |
760 | ||
761 | if (set) | |
762 | ret = set_port_feature(hdev, port1, USB_PORT_FEAT_POWER); | |
763 | else | |
ad493e5e LT |
764 | ret = usb_clear_port_feature(hdev, port1, USB_PORT_FEAT_POWER); |
765 | ||
d5c3834e DW |
766 | if (ret) |
767 | return ret; | |
768 | ||
769 | if (set) | |
770 | set_bit(port1, hub->power_bits); | |
771 | else | |
772 | clear_bit(port1, hub->power_bits); | |
773 | return 0; | |
971fcd49 LT |
774 | } |
775 | ||
1da177e4 | 776 | /** |
cb88a1b8 AS |
777 | * usb_hub_clear_tt_buffer - clear control/bulk TT state in high speed hub |
778 | * @urb: an URB associated with the failed or incomplete split transaction | |
1da177e4 LT |
779 | * |
780 | * High speed HCDs use this to tell the hub driver that some split control or | |
781 | * bulk transaction failed in a way that requires clearing internal state of | |
782 | * a transaction translator. This is normally detected (and reported) from | |
783 | * interrupt context. | |
784 | * | |
785 | * It may not be possible for that hub to handle additional full (or low) | |
786 | * speed transactions until that state is fully cleared out. | |
626f090c YB |
787 | * |
788 | * Return: 0 if successful. A negative error code otherwise. | |
1da177e4 | 789 | */ |
cb88a1b8 | 790 | int usb_hub_clear_tt_buffer(struct urb *urb) |
1da177e4 | 791 | { |
cb88a1b8 AS |
792 | struct usb_device *udev = urb->dev; |
793 | int pipe = urb->pipe; | |
1da177e4 LT |
794 | struct usb_tt *tt = udev->tt; |
795 | unsigned long flags; | |
796 | struct usb_tt_clear *clear; | |
797 | ||
798 | /* we've got to cope with an arbitrary number of pending TT clears, | |
799 | * since each TT has "at least two" buffers that can need it (and | |
800 | * there can be many TTs per hub). even if they're uncommon. | |
801 | */ | |
d544d273 GKH |
802 | clear = kmalloc(sizeof *clear, GFP_ATOMIC); |
803 | if (clear == NULL) { | |
166b8639 | 804 | dev_err(&udev->dev, "can't save CLEAR_TT_BUFFER state\n"); |
1da177e4 | 805 | /* FIXME recover somehow ... RESET_TT? */ |
cb88a1b8 | 806 | return -ENOMEM; |
1da177e4 LT |
807 | } |
808 | ||
809 | /* info that CLEAR_TT_BUFFER needs */ | |
810 | clear->tt = tt->multi ? udev->ttport : 1; | |
811 | clear->devinfo = usb_pipeendpoint (pipe); | |
812 | clear->devinfo |= udev->devnum << 4; | |
166b8639 | 813 | clear->devinfo |= usb_pipecontrol(pipe) |
1da177e4 LT |
814 | ? (USB_ENDPOINT_XFER_CONTROL << 11) |
815 | : (USB_ENDPOINT_XFER_BULK << 11); | |
166b8639 | 816 | if (usb_pipein(pipe)) |
1da177e4 | 817 | clear->devinfo |= 1 << 15; |
cb88a1b8 AS |
818 | |
819 | /* info for completion callback */ | |
820 | clear->hcd = bus_to_hcd(udev->bus); | |
821 | clear->ep = urb->ep; | |
822 | ||
1da177e4 | 823 | /* tell keventd to clear state for this TT */ |
166b8639 CM |
824 | spin_lock_irqsave(&tt->lock, flags); |
825 | list_add_tail(&clear->clear_list, &tt->clear_list); | |
cb88a1b8 | 826 | schedule_work(&tt->clear_work); |
166b8639 | 827 | spin_unlock_irqrestore(&tt->lock, flags); |
cb88a1b8 | 828 | return 0; |
1da177e4 | 829 | } |
cb88a1b8 | 830 | EXPORT_SYMBOL_GPL(usb_hub_clear_tt_buffer); |
1da177e4 | 831 | |
7ad3c470 | 832 | static void hub_power_on(struct usb_hub *hub, bool do_delay) |
1da177e4 LT |
833 | { |
834 | int port1; | |
4489a571 AS |
835 | |
836 | /* Enable power on each port. Some hubs have reserved values | |
837 | * of LPSM (> 2) in their descriptors, even though they are | |
838 | * USB 2.0 hubs. Some hubs do not implement port-power switching | |
839 | * but only emulate it. In all cases, the ports won't work | |
840 | * unless we send these messages to the hub. | |
841 | */ | |
9262c19d | 842 | if (hub_is_port_power_switchable(hub)) |
1da177e4 | 843 | dev_dbg(hub->intfdev, "enabling power on all ports\n"); |
4489a571 AS |
844 | else |
845 | dev_dbg(hub->intfdev, "trying to enable port power on " | |
846 | "non-switchable hub\n"); | |
3bbc47d8 | 847 | for (port1 = 1; port1 <= hub->hdev->maxchild; port1++) |
d5c3834e | 848 | if (test_bit(port1, hub->power_bits)) |
ad493e5e LT |
849 | set_port_feature(hub->hdev, port1, USB_PORT_FEAT_POWER); |
850 | else | |
851 | usb_clear_port_feature(hub->hdev, port1, | |
852 | USB_PORT_FEAT_POWER); | |
8520f380 | 853 | if (do_delay) |
7ad3c470 | 854 | msleep(hub_power_on_good_delay(hub)); |
1da177e4 LT |
855 | } |
856 | ||
1da177e4 LT |
857 | static int hub_hub_status(struct usb_hub *hub, |
858 | u16 *status, u16 *change) | |
859 | { | |
860 | int ret; | |
861 | ||
db90e7a1 | 862 | mutex_lock(&hub->status_mutex); |
1da177e4 | 863 | ret = get_hub_status(hub->hdev, &hub->status->hub); |
e9e88fb7 AS |
864 | if (ret < 0) { |
865 | if (ret != -ENODEV) | |
866 | dev_err(hub->intfdev, | |
867 | "%s failed (err = %d)\n", __func__, ret); | |
868 | } else { | |
1da177e4 | 869 | *status = le16_to_cpu(hub->status->hub.wHubStatus); |
469271f8 | 870 | *change = le16_to_cpu(hub->status->hub.wHubChange); |
1da177e4 LT |
871 | ret = 0; |
872 | } | |
db90e7a1 | 873 | mutex_unlock(&hub->status_mutex); |
1da177e4 LT |
874 | return ret; |
875 | } | |
876 | ||
41e7e056 SS |
877 | static int hub_set_port_link_state(struct usb_hub *hub, int port1, |
878 | unsigned int link_status) | |
879 | { | |
880 | return set_port_feature(hub->hdev, | |
881 | port1 | (link_status << 3), | |
882 | USB_PORT_FEAT_LINK_STATE); | |
883 | } | |
884 | ||
885 | /* | |
886 | * If USB 3.0 ports are placed into the Disabled state, they will no longer | |
887 | * detect any device connects or disconnects. This is generally not what the | |
888 | * USB core wants, since it expects a disabled port to produce a port status | |
889 | * change event when a new device connects. | |
890 | * | |
891 | * Instead, set the link state to Disabled, wait for the link to settle into | |
892 | * that state, clear any change bits, and then put the port into the RxDetect | |
893 | * state. | |
894 | */ | |
895 | static int hub_usb3_port_disable(struct usb_hub *hub, int port1) | |
896 | { | |
897 | int ret; | |
898 | int total_time; | |
899 | u16 portchange, portstatus; | |
900 | ||
901 | if (!hub_is_superspeed(hub->hdev)) | |
902 | return -EINVAL; | |
903 | ||
bb86cf56 GG |
904 | ret = hub_port_status(hub, port1, &portstatus, &portchange); |
905 | if (ret < 0) | |
906 | return ret; | |
907 | ||
908 | /* | |
909 | * USB controller Advanced Micro Devices, Inc. [AMD] FCH USB XHCI | |
910 | * Controller [1022:7814] will have spurious result making the following | |
911 | * usb 3.0 device hotplugging route to the 2.0 root hub and recognized | |
912 | * as high-speed device if we set the usb 3.0 port link state to | |
913 | * Disabled. Since it's already in USB_SS_PORT_LS_RX_DETECT state, we | |
914 | * check the state here to avoid the bug. | |
915 | */ | |
916 | if ((portstatus & USB_PORT_STAT_LINK_STATE) == | |
917 | USB_SS_PORT_LS_RX_DETECT) { | |
918 | dev_dbg(&hub->ports[port1 - 1]->dev, | |
919 | "Not disabling port; link state is RxDetect\n"); | |
920 | return ret; | |
921 | } | |
922 | ||
41e7e056 | 923 | ret = hub_set_port_link_state(hub, port1, USB_SS_PORT_LS_SS_DISABLED); |
e9e88fb7 | 924 | if (ret) |
41e7e056 | 925 | return ret; |
41e7e056 SS |
926 | |
927 | /* Wait for the link to enter the disabled state. */ | |
928 | for (total_time = 0; ; total_time += HUB_DEBOUNCE_STEP) { | |
929 | ret = hub_port_status(hub, port1, &portstatus, &portchange); | |
930 | if (ret < 0) | |
931 | return ret; | |
932 | ||
933 | if ((portstatus & USB_PORT_STAT_LINK_STATE) == | |
934 | USB_SS_PORT_LS_SS_DISABLED) | |
935 | break; | |
936 | if (total_time >= HUB_DEBOUNCE_TIMEOUT) | |
937 | break; | |
938 | msleep(HUB_DEBOUNCE_STEP); | |
939 | } | |
940 | if (total_time >= HUB_DEBOUNCE_TIMEOUT) | |
d99f6b41 DW |
941 | dev_warn(&hub->ports[port1 - 1]->dev, |
942 | "Could not disable after %d ms\n", total_time); | |
41e7e056 SS |
943 | |
944 | return hub_set_port_link_state(hub, port1, USB_SS_PORT_LS_RX_DETECT); | |
945 | } | |
946 | ||
8b28c752 AS |
947 | static int hub_port_disable(struct usb_hub *hub, int port1, int set_state) |
948 | { | |
d99f6b41 | 949 | struct usb_port *port_dev = hub->ports[port1 - 1]; |
8b28c752 | 950 | struct usb_device *hdev = hub->hdev; |
0458d5b4 | 951 | int ret = 0; |
8b28c752 | 952 | |
d99f6b41 DW |
953 | if (port_dev->child && set_state) |
954 | usb_set_device_state(port_dev->child, USB_STATE_NOTATTACHED); | |
41e7e056 SS |
955 | if (!hub->error) { |
956 | if (hub_is_superspeed(hub->hdev)) | |
957 | ret = hub_usb3_port_disable(hub, port1); | |
958 | else | |
ad493e5e | 959 | ret = usb_clear_port_feature(hdev, port1, |
41e7e056 SS |
960 | USB_PORT_FEAT_ENABLE); |
961 | } | |
e9e88fb7 | 962 | if (ret && ret != -ENODEV) |
d99f6b41 | 963 | dev_err(&port_dev->dev, "cannot disable (err = %d)\n", ret); |
8b28c752 AS |
964 | return ret; |
965 | } | |
966 | ||
0458d5b4 | 967 | /* |
6d42fcdb | 968 | * Disable a port and mark a logical connect-change event, so that some |
37ebb549 | 969 | * time later hub_wq will disconnect() any existing usb_device on the port |
0458d5b4 AS |
970 | * and will re-enumerate if there actually is a device attached. |
971 | */ | |
972 | static void hub_port_logical_disconnect(struct usb_hub *hub, int port1) | |
973 | { | |
d99f6b41 | 974 | dev_dbg(&hub->ports[port1 - 1]->dev, "logical disconnect\n"); |
0458d5b4 | 975 | hub_port_disable(hub, port1, 1); |
7d069b7d | 976 | |
0458d5b4 AS |
977 | /* FIXME let caller ask to power down the port: |
978 | * - some devices won't enumerate without a VBUS power cycle | |
979 | * - SRP saves power that way | |
980 | * - ... new call, TBD ... | |
981 | * That's easy if this hub can switch power per-port, and | |
37ebb549 | 982 | * hub_wq reactivates the port later (timer, SRP, etc). |
0458d5b4 AS |
983 | * Powerdown must be optional, because of reset/DFU. |
984 | */ | |
985 | ||
986 | set_bit(port1, hub->change_bits); | |
32a69589 | 987 | kick_hub_wq(hub); |
0458d5b4 AS |
988 | } |
989 | ||
253e0572 AS |
990 | /** |
991 | * usb_remove_device - disable a device's port on its parent hub | |
992 | * @udev: device to be disabled and removed | |
993 | * Context: @udev locked, must be able to sleep. | |
994 | * | |
37ebb549 | 995 | * After @udev's port has been disabled, hub_wq is notified and it will |
253e0572 AS |
996 | * see that the device has been disconnected. When the device is |
997 | * physically unplugged and something is plugged in, the events will | |
998 | * be received and processed normally. | |
626f090c YB |
999 | * |
1000 | * Return: 0 if successful. A negative error code otherwise. | |
253e0572 AS |
1001 | */ |
1002 | int usb_remove_device(struct usb_device *udev) | |
1003 | { | |
1004 | struct usb_hub *hub; | |
1005 | struct usb_interface *intf; | |
1006 | ||
1007 | if (!udev->parent) /* Can't remove a root hub */ | |
1008 | return -EINVAL; | |
ad493e5e | 1009 | hub = usb_hub_to_struct_hub(udev->parent); |
253e0572 AS |
1010 | intf = to_usb_interface(hub->intfdev); |
1011 | ||
1012 | usb_autopm_get_interface(intf); | |
1013 | set_bit(udev->portnum, hub->removed_bits); | |
1014 | hub_port_logical_disconnect(hub, udev->portnum); | |
1015 | usb_autopm_put_interface(intf); | |
1016 | return 0; | |
1017 | } | |
1018 | ||
6ee0b270 | 1019 | enum hub_activation_type { |
8e4ceb38 | 1020 | HUB_INIT, HUB_INIT2, HUB_INIT3, /* INITs must come first */ |
8520f380 | 1021 | HUB_POST_RESET, HUB_RESUME, HUB_RESET_RESUME, |
6ee0b270 | 1022 | }; |
5e6effae | 1023 | |
8520f380 AS |
1024 | static void hub_init_func2(struct work_struct *ws); |
1025 | static void hub_init_func3(struct work_struct *ws); | |
1026 | ||
f2835219 | 1027 | static void hub_activate(struct usb_hub *hub, enum hub_activation_type type) |
5e6effae AS |
1028 | { |
1029 | struct usb_device *hdev = hub->hdev; | |
653a39d1 SS |
1030 | struct usb_hcd *hcd; |
1031 | int ret; | |
5e6effae | 1032 | int port1; |
f2835219 | 1033 | int status; |
948fea37 | 1034 | bool need_debounce_delay = false; |
8520f380 AS |
1035 | unsigned delay; |
1036 | ||
1037 | /* Continue a partial initialization */ | |
e50293ef AS |
1038 | if (type == HUB_INIT2 || type == HUB_INIT3) { |
1039 | device_lock(hub->intfdev); | |
1040 | ||
1041 | /* Was the hub disconnected while we were waiting? */ | |
1042 | if (hub->disconnected) { | |
1043 | device_unlock(hub->intfdev); | |
1044 | kref_put(&hub->kref, hub_release); | |
1045 | return; | |
1046 | } | |
1047 | if (type == HUB_INIT2) | |
1048 | goto init2; | |
8520f380 | 1049 | goto init3; |
e50293ef AS |
1050 | } |
1051 | kref_get(&hub->kref); | |
5e6effae | 1052 | |
a45aa3b3 EF |
1053 | /* The superspeed hub except for root hub has to use Hub Depth |
1054 | * value as an offset into the route string to locate the bits | |
1055 | * it uses to determine the downstream port number. So hub driver | |
1056 | * should send a set hub depth request to superspeed hub after | |
1057 | * the superspeed hub is set configuration in initialization or | |
1058 | * reset procedure. | |
1059 | * | |
1060 | * After a resume, port power should still be on. | |
f2835219 AS |
1061 | * For any other type of activation, turn it on. |
1062 | */ | |
8520f380 | 1063 | if (type != HUB_RESUME) { |
a45aa3b3 EF |
1064 | if (hdev->parent && hub_is_superspeed(hdev)) { |
1065 | ret = usb_control_msg(hdev, usb_sndctrlpipe(hdev, 0), | |
1066 | HUB_SET_DEPTH, USB_RT_HUB, | |
1067 | hdev->level - 1, 0, NULL, 0, | |
1068 | USB_CTRL_SET_TIMEOUT); | |
1069 | if (ret < 0) | |
1070 | dev_err(hub->intfdev, | |
1071 | "set hub depth failed\n"); | |
1072 | } | |
8520f380 AS |
1073 | |
1074 | /* Speed up system boot by using a delayed_work for the | |
1075 | * hub's initial power-up delays. This is pretty awkward | |
1076 | * and the implementation looks like a home-brewed sort of | |
1077 | * setjmp/longjmp, but it saves at least 100 ms for each | |
1078 | * root hub (assuming usbcore is compiled into the kernel | |
1079 | * rather than as a module). It adds up. | |
1080 | * | |
1081 | * This can't be done for HUB_RESUME or HUB_RESET_RESUME | |
1082 | * because for those activation types the ports have to be | |
1083 | * operational when we return. In theory this could be done | |
1084 | * for HUB_POST_RESET, but it's easier not to. | |
1085 | */ | |
1086 | if (type == HUB_INIT) { | |
17a364e2 | 1087 | delay = hub_power_on_good_delay(hub); |
7ad3c470 DW |
1088 | |
1089 | hub_power_on(hub, false); | |
77fa83cf | 1090 | INIT_DELAYED_WORK(&hub->init_work, hub_init_func2); |
22f6a0f0 SD |
1091 | queue_delayed_work(system_power_efficient_wq, |
1092 | &hub->init_work, | |
8520f380 | 1093 | msecs_to_jiffies(delay)); |
61fbeba1 AS |
1094 | |
1095 | /* Suppress autosuspend until init is done */ | |
8e4ceb38 AS |
1096 | usb_autopm_get_interface_no_resume( |
1097 | to_usb_interface(hub->intfdev)); | |
8520f380 | 1098 | return; /* Continues at init2: below */ |
653a39d1 SS |
1099 | } else if (type == HUB_RESET_RESUME) { |
1100 | /* The internal host controller state for the hub device | |
1101 | * may be gone after a host power loss on system resume. | |
1102 | * Update the device's info so the HW knows it's a hub. | |
1103 | */ | |
1104 | hcd = bus_to_hcd(hdev->bus); | |
1105 | if (hcd->driver->update_hub_device) { | |
1106 | ret = hcd->driver->update_hub_device(hcd, hdev, | |
1107 | &hub->tt, GFP_NOIO); | |
1108 | if (ret < 0) { | |
1109 | dev_err(hub->intfdev, "Host not " | |
1110 | "accepting hub info " | |
1111 | "update.\n"); | |
1112 | dev_err(hub->intfdev, "LS/FS devices " | |
1113 | "and hubs may not work " | |
1114 | "under this hub\n."); | |
1115 | } | |
1116 | } | |
1117 | hub_power_on(hub, true); | |
8520f380 AS |
1118 | } else { |
1119 | hub_power_on(hub, true); | |
1120 | } | |
1121 | } | |
1122 | init2: | |
f2835219 | 1123 | |
d99f6b41 | 1124 | /* |
37ebb549 | 1125 | * Check each port and set hub->change_bits to let hub_wq know |
6ee0b270 | 1126 | * which ports need attention. |
5e6effae AS |
1127 | */ |
1128 | for (port1 = 1; port1 <= hdev->maxchild; ++port1) { | |
d99f6b41 DW |
1129 | struct usb_port *port_dev = hub->ports[port1 - 1]; |
1130 | struct usb_device *udev = port_dev->child; | |
5e6effae AS |
1131 | u16 portstatus, portchange; |
1132 | ||
6ee0b270 AS |
1133 | portstatus = portchange = 0; |
1134 | status = hub_port_status(hub, port1, &portstatus, &portchange); | |
1135 | if (udev || (portstatus & USB_PORT_STAT_CONNECTION)) | |
d99f6b41 DW |
1136 | dev_dbg(&port_dev->dev, "status %04x change %04x\n", |
1137 | portstatus, portchange); | |
6ee0b270 | 1138 | |
d99f6b41 DW |
1139 | /* |
1140 | * After anything other than HUB_RESUME (i.e., initialization | |
6ee0b270 AS |
1141 | * or any sort of reset), every port should be disabled. |
1142 | * Unconnected ports should likewise be disabled (paranoia), | |
1143 | * and so should ports for which we have no usb_device. | |
1144 | */ | |
1145 | if ((portstatus & USB_PORT_STAT_ENABLE) && ( | |
1146 | type != HUB_RESUME || | |
1147 | !(portstatus & USB_PORT_STAT_CONNECTION) || | |
1148 | !udev || | |
1149 | udev->state == USB_STATE_NOTATTACHED)) { | |
9f0a6cd3 AX |
1150 | /* |
1151 | * USB3 protocol ports will automatically transition | |
1152 | * to Enabled state when detect an USB3.0 device attach. | |
fd1ac4cf DW |
1153 | * Do not disable USB3 protocol ports, just pretend |
1154 | * power was lost | |
9f0a6cd3 | 1155 | */ |
fd1ac4cf DW |
1156 | portstatus &= ~USB_PORT_STAT_ENABLE; |
1157 | if (!hub_is_superspeed(hdev)) | |
ad493e5e | 1158 | usb_clear_port_feature(hdev, port1, |
9f0a6cd3 | 1159 | USB_PORT_FEAT_ENABLE); |
5e6effae AS |
1160 | } |
1161 | ||
948fea37 AS |
1162 | /* Clear status-change flags; we'll debounce later */ |
1163 | if (portchange & USB_PORT_STAT_C_CONNECTION) { | |
1164 | need_debounce_delay = true; | |
ad493e5e | 1165 | usb_clear_port_feature(hub->hdev, port1, |
948fea37 AS |
1166 | USB_PORT_FEAT_C_CONNECTION); |
1167 | } | |
1168 | if (portchange & USB_PORT_STAT_C_ENABLE) { | |
1169 | need_debounce_delay = true; | |
ad493e5e | 1170 | usb_clear_port_feature(hub->hdev, port1, |
948fea37 AS |
1171 | USB_PORT_FEAT_C_ENABLE); |
1172 | } | |
e92aee33 JW |
1173 | if (portchange & USB_PORT_STAT_C_RESET) { |
1174 | need_debounce_delay = true; | |
1175 | usb_clear_port_feature(hub->hdev, port1, | |
1176 | USB_PORT_FEAT_C_RESET); | |
1177 | } | |
79c3dd81 DZ |
1178 | if ((portchange & USB_PORT_STAT_C_BH_RESET) && |
1179 | hub_is_superspeed(hub->hdev)) { | |
1180 | need_debounce_delay = true; | |
ad493e5e | 1181 | usb_clear_port_feature(hub->hdev, port1, |
79c3dd81 DZ |
1182 | USB_PORT_FEAT_C_BH_PORT_RESET); |
1183 | } | |
253e0572 AS |
1184 | /* We can forget about a "removed" device when there's a |
1185 | * physical disconnect or the connect status changes. | |
1186 | */ | |
1187 | if (!(portstatus & USB_PORT_STAT_CONNECTION) || | |
1188 | (portchange & USB_PORT_STAT_C_CONNECTION)) | |
1189 | clear_bit(port1, hub->removed_bits); | |
1190 | ||
6ee0b270 | 1191 | if (!udev || udev->state == USB_STATE_NOTATTACHED) { |
37ebb549 | 1192 | /* Tell hub_wq to disconnect the device or |
6ee0b270 AS |
1193 | * check for a new connection |
1194 | */ | |
08d1dec6 SG |
1195 | if (udev || (portstatus & USB_PORT_STAT_CONNECTION) || |
1196 | (portstatus & USB_PORT_STAT_OVERCURRENT)) | |
6ee0b270 AS |
1197 | set_bit(port1, hub->change_bits); |
1198 | ||
1199 | } else if (portstatus & USB_PORT_STAT_ENABLE) { | |
72937e1e SS |
1200 | bool port_resumed = (portstatus & |
1201 | USB_PORT_STAT_LINK_STATE) == | |
1202 | USB_SS_PORT_LS_U0; | |
6ee0b270 AS |
1203 | /* The power session apparently survived the resume. |
1204 | * If there was an overcurrent or suspend change | |
37ebb549 | 1205 | * (i.e., remote wakeup request), have hub_wq |
72937e1e SS |
1206 | * take care of it. Look at the port link state |
1207 | * for USB 3.0 hubs, since they don't have a suspend | |
1208 | * change bit, and they don't set the port link change | |
1209 | * bit on device-initiated resume. | |
6ee0b270 | 1210 | */ |
72937e1e SS |
1211 | if (portchange || (hub_is_superspeed(hub->hdev) && |
1212 | port_resumed)) | |
6ee0b270 | 1213 | set_bit(port1, hub->change_bits); |
5e6effae | 1214 | |
6ee0b270 | 1215 | } else if (udev->persist_enabled) { |
6ee0b270 | 1216 | #ifdef CONFIG_PM |
5e6effae | 1217 | udev->reset_resume = 1; |
6ee0b270 | 1218 | #endif |
ad493e5e LT |
1219 | /* Don't set the change_bits when the device |
1220 | * was powered off. | |
1221 | */ | |
d5c3834e | 1222 | if (test_bit(port1, hub->power_bits)) |
ad493e5e | 1223 | set_bit(port1, hub->change_bits); |
8808f00c | 1224 | |
6ee0b270 | 1225 | } else { |
37ebb549 | 1226 | /* The power session is gone; tell hub_wq */ |
6ee0b270 AS |
1227 | usb_set_device_state(udev, USB_STATE_NOTATTACHED); |
1228 | set_bit(port1, hub->change_bits); | |
5e6effae | 1229 | } |
5e6effae AS |
1230 | } |
1231 | ||
948fea37 AS |
1232 | /* If no port-status-change flags were set, we don't need any |
1233 | * debouncing. If flags were set we can try to debounce the | |
37ebb549 | 1234 | * ports all at once right now, instead of letting hub_wq do them |
948fea37 AS |
1235 | * one at a time later on. |
1236 | * | |
37ebb549 | 1237 | * If any port-status changes do occur during this delay, hub_wq |
948fea37 AS |
1238 | * will see them later and handle them normally. |
1239 | */ | |
8520f380 AS |
1240 | if (need_debounce_delay) { |
1241 | delay = HUB_DEBOUNCE_STABLE; | |
1242 | ||
1243 | /* Don't do a long sleep inside a workqueue routine */ | |
1244 | if (type == HUB_INIT2) { | |
77fa83cf | 1245 | INIT_DELAYED_WORK(&hub->init_work, hub_init_func3); |
22f6a0f0 SD |
1246 | queue_delayed_work(system_power_efficient_wq, |
1247 | &hub->init_work, | |
8520f380 | 1248 | msecs_to_jiffies(delay)); |
e50293ef | 1249 | device_unlock(hub->intfdev); |
8520f380 AS |
1250 | return; /* Continues at init3: below */ |
1251 | } else { | |
1252 | msleep(delay); | |
1253 | } | |
1254 | } | |
1255 | init3: | |
f2835219 AS |
1256 | hub->quiescing = 0; |
1257 | ||
1258 | status = usb_submit_urb(hub->urb, GFP_NOIO); | |
1259 | if (status < 0) | |
1260 | dev_err(hub->intfdev, "activate --> %d\n", status); | |
1261 | if (hub->has_indicators && blinkenlights) | |
22f6a0f0 SD |
1262 | queue_delayed_work(system_power_efficient_wq, |
1263 | &hub->leds, LED_CYCLE_PERIOD); | |
f2835219 AS |
1264 | |
1265 | /* Scan all ports that need attention */ | |
32a69589 | 1266 | kick_hub_wq(hub); |
8e4ceb38 AS |
1267 | |
1268 | /* Allow autosuspend if it was suppressed */ | |
1269 | if (type <= HUB_INIT3) | |
1270 | usb_autopm_put_interface_async(to_usb_interface(hub->intfdev)); | |
e50293ef AS |
1271 | |
1272 | if (type == HUB_INIT2 || type == HUB_INIT3) | |
1273 | device_unlock(hub->intfdev); | |
1274 | ||
1275 | kref_put(&hub->kref, hub_release); | |
5e6effae AS |
1276 | } |
1277 | ||
8520f380 AS |
1278 | /* Implement the continuations for the delays above */ |
1279 | static void hub_init_func2(struct work_struct *ws) | |
1280 | { | |
1281 | struct usb_hub *hub = container_of(ws, struct usb_hub, init_work.work); | |
1282 | ||
1283 | hub_activate(hub, HUB_INIT2); | |
1284 | } | |
1285 | ||
1286 | static void hub_init_func3(struct work_struct *ws) | |
1287 | { | |
1288 | struct usb_hub *hub = container_of(ws, struct usb_hub, init_work.work); | |
1289 | ||
1290 | hub_activate(hub, HUB_INIT3); | |
1291 | } | |
1292 | ||
4330354f AS |
1293 | enum hub_quiescing_type { |
1294 | HUB_DISCONNECT, HUB_PRE_RESET, HUB_SUSPEND | |
1295 | }; | |
1296 | ||
1297 | static void hub_quiesce(struct usb_hub *hub, enum hub_quiescing_type type) | |
1298 | { | |
1299 | struct usb_device *hdev = hub->hdev; | |
1300 | int i; | |
1301 | ||
8520f380 AS |
1302 | cancel_delayed_work_sync(&hub->init_work); |
1303 | ||
37ebb549 | 1304 | /* hub_wq and related activity won't re-trigger */ |
4330354f AS |
1305 | hub->quiescing = 1; |
1306 | ||
1307 | if (type != HUB_SUSPEND) { | |
1308 | /* Disconnect all the children */ | |
1309 | for (i = 0; i < hdev->maxchild; ++i) { | |
ff823c79 LT |
1310 | if (hub->ports[i]->child) |
1311 | usb_disconnect(&hub->ports[i]->child); | |
4330354f AS |
1312 | } |
1313 | } | |
1314 | ||
37ebb549 | 1315 | /* Stop hub_wq and related activity */ |
4330354f AS |
1316 | usb_kill_urb(hub->urb); |
1317 | if (hub->has_indicators) | |
1318 | cancel_delayed_work_sync(&hub->leds); | |
1319 | if (hub->tt.hub) | |
036546bf | 1320 | flush_work(&hub->tt.clear_work); |
4330354f AS |
1321 | } |
1322 | ||
600856c2 AS |
1323 | static void hub_pm_barrier_for_all_ports(struct usb_hub *hub) |
1324 | { | |
1325 | int i; | |
1326 | ||
1327 | for (i = 0; i < hub->hdev->maxchild; ++i) | |
1328 | pm_runtime_barrier(&hub->ports[i]->dev); | |
1329 | } | |
1330 | ||
3eb14915 AS |
1331 | /* caller has locked the hub device */ |
1332 | static int hub_pre_reset(struct usb_interface *intf) | |
1333 | { | |
1334 | struct usb_hub *hub = usb_get_intfdata(intf); | |
1335 | ||
4330354f | 1336 | hub_quiesce(hub, HUB_PRE_RESET); |
600856c2 AS |
1337 | hub->in_reset = 1; |
1338 | hub_pm_barrier_for_all_ports(hub); | |
f07600cf | 1339 | return 0; |
7d069b7d AS |
1340 | } |
1341 | ||
1342 | /* caller has locked the hub device */ | |
f07600cf | 1343 | static int hub_post_reset(struct usb_interface *intf) |
7d069b7d | 1344 | { |
7de18d8b AS |
1345 | struct usb_hub *hub = usb_get_intfdata(intf); |
1346 | ||
600856c2 AS |
1347 | hub->in_reset = 0; |
1348 | hub_pm_barrier_for_all_ports(hub); | |
f2835219 | 1349 | hub_activate(hub, HUB_POST_RESET); |
f07600cf | 1350 | return 0; |
7d069b7d AS |
1351 | } |
1352 | ||
1da177e4 LT |
1353 | static int hub_configure(struct usb_hub *hub, |
1354 | struct usb_endpoint_descriptor *endpoint) | |
1355 | { | |
b356b7c7 | 1356 | struct usb_hcd *hcd; |
1da177e4 LT |
1357 | struct usb_device *hdev = hub->hdev; |
1358 | struct device *hub_dev = hub->intfdev; | |
1359 | u16 hubstatus, hubchange; | |
74ad9bd2 | 1360 | u16 wHubCharacteristics; |
1da177e4 | 1361 | unsigned int pipe; |
fa2a9566 | 1362 | int maxp, ret, i; |
7cbe5dca | 1363 | char *message = "out of memory"; |
430ee58e SAS |
1364 | unsigned unit_load; |
1365 | unsigned full_load; | |
d8521afe | 1366 | unsigned maxchild; |
1da177e4 | 1367 | |
d697cdda | 1368 | hub->buffer = kmalloc(sizeof(*hub->buffer), GFP_KERNEL); |
1da177e4 | 1369 | if (!hub->buffer) { |
1da177e4 LT |
1370 | ret = -ENOMEM; |
1371 | goto fail; | |
1372 | } | |
1373 | ||
1374 | hub->status = kmalloc(sizeof(*hub->status), GFP_KERNEL); | |
1375 | if (!hub->status) { | |
1da177e4 LT |
1376 | ret = -ENOMEM; |
1377 | goto fail; | |
1378 | } | |
db90e7a1 | 1379 | mutex_init(&hub->status_mutex); |
1da177e4 LT |
1380 | |
1381 | hub->descriptor = kmalloc(sizeof(*hub->descriptor), GFP_KERNEL); | |
1382 | if (!hub->descriptor) { | |
1da177e4 LT |
1383 | ret = -ENOMEM; |
1384 | goto fail; | |
1385 | } | |
1386 | ||
1387 | /* Request the entire hub descriptor. | |
1388 | * hub->descriptor can handle USB_MAXCHILDREN ports, | |
1389 | * but the hub can/will return fewer bytes here. | |
1390 | */ | |
dbe79bbe | 1391 | ret = get_hub_descriptor(hdev, hub->descriptor); |
1da177e4 LT |
1392 | if (ret < 0) { |
1393 | message = "can't read hub descriptor"; | |
1394 | goto fail; | |
1395 | } else if (hub->descriptor->bNbrPorts > USB_MAXCHILDREN) { | |
1396 | message = "hub has too many ports!"; | |
1397 | ret = -ENODEV; | |
1398 | goto fail; | |
769d7368 DL |
1399 | } else if (hub->descriptor->bNbrPorts == 0) { |
1400 | message = "hub doesn't have any ports!"; | |
1401 | ret = -ENODEV; | |
1402 | goto fail; | |
1da177e4 LT |
1403 | } |
1404 | ||
d8521afe DW |
1405 | maxchild = hub->descriptor->bNbrPorts; |
1406 | dev_info(hub_dev, "%d port%s detected\n", maxchild, | |
1407 | (maxchild == 1) ? "" : "s"); | |
1da177e4 | 1408 | |
d8521afe | 1409 | hub->ports = kzalloc(maxchild * sizeof(struct usb_port *), GFP_KERNEL); |
ff823c79 | 1410 | if (!hub->ports) { |
7cbe5dca AS |
1411 | ret = -ENOMEM; |
1412 | goto fail; | |
1413 | } | |
1414 | ||
74ad9bd2 | 1415 | wHubCharacteristics = le16_to_cpu(hub->descriptor->wHubCharacteristics); |
430ee58e SAS |
1416 | if (hub_is_superspeed(hdev)) { |
1417 | unit_load = 150; | |
1418 | full_load = 900; | |
1419 | } else { | |
1420 | unit_load = 100; | |
1421 | full_load = 500; | |
1422 | } | |
1da177e4 | 1423 | |
dbe79bbe JY |
1424 | /* FIXME for USB 3.0, skip for now */ |
1425 | if ((wHubCharacteristics & HUB_CHAR_COMPOUND) && | |
1426 | !(hub_is_superspeed(hdev))) { | |
469271f8 | 1427 | char portstr[USB_MAXCHILDREN + 1]; |
1da177e4 | 1428 | |
d8521afe | 1429 | for (i = 0; i < maxchild; i++) |
dbe79bbe | 1430 | portstr[i] = hub->descriptor->u.hs.DeviceRemovable |
1da177e4 LT |
1431 | [((i + 1) / 8)] & (1 << ((i + 1) % 8)) |
1432 | ? 'F' : 'R'; | |
d8521afe | 1433 | portstr[maxchild] = 0; |
1da177e4 LT |
1434 | dev_dbg(hub_dev, "compound device; port removable status: %s\n", portstr); |
1435 | } else | |
1436 | dev_dbg(hub_dev, "standalone hub\n"); | |
1437 | ||
74ad9bd2 | 1438 | switch (wHubCharacteristics & HUB_CHAR_LPSM) { |
7bf01185 AD |
1439 | case HUB_CHAR_COMMON_LPSM: |
1440 | dev_dbg(hub_dev, "ganged power switching\n"); | |
1441 | break; | |
1442 | case HUB_CHAR_INDV_PORT_LPSM: | |
1443 | dev_dbg(hub_dev, "individual port power switching\n"); | |
1444 | break; | |
1445 | case HUB_CHAR_NO_LPSM: | |
1446 | case HUB_CHAR_LPSM: | |
1447 | dev_dbg(hub_dev, "no power switching (usb 1.0)\n"); | |
1448 | break; | |
1da177e4 LT |
1449 | } |
1450 | ||
74ad9bd2 | 1451 | switch (wHubCharacteristics & HUB_CHAR_OCPM) { |
7bf01185 AD |
1452 | case HUB_CHAR_COMMON_OCPM: |
1453 | dev_dbg(hub_dev, "global over-current protection\n"); | |
1454 | break; | |
1455 | case HUB_CHAR_INDV_PORT_OCPM: | |
1456 | dev_dbg(hub_dev, "individual port over-current protection\n"); | |
1457 | break; | |
1458 | case HUB_CHAR_NO_OCPM: | |
1459 | case HUB_CHAR_OCPM: | |
1460 | dev_dbg(hub_dev, "no over-current protection\n"); | |
1461 | break; | |
1da177e4 LT |
1462 | } |
1463 | ||
17248569 CM |
1464 | spin_lock_init(&hub->tt.lock); |
1465 | INIT_LIST_HEAD(&hub->tt.clear_list); | |
cb88a1b8 | 1466 | INIT_WORK(&hub->tt.clear_work, hub_tt_work); |
1da177e4 | 1467 | switch (hdev->descriptor.bDeviceProtocol) { |
7bf01185 AD |
1468 | case USB_HUB_PR_FS: |
1469 | break; | |
1470 | case USB_HUB_PR_HS_SINGLE_TT: | |
1471 | dev_dbg(hub_dev, "Single TT\n"); | |
1472 | hub->tt.hub = hdev; | |
1473 | break; | |
1474 | case USB_HUB_PR_HS_MULTI_TT: | |
1475 | ret = usb_set_interface(hdev, 0, 1); | |
1476 | if (ret == 0) { | |
1477 | dev_dbg(hub_dev, "TT per port\n"); | |
1478 | hub->tt.multi = 1; | |
1479 | } else | |
1480 | dev_err(hub_dev, "Using single TT (err %d)\n", | |
1481 | ret); | |
1482 | hub->tt.hub = hdev; | |
1483 | break; | |
1484 | case USB_HUB_PR_SS: | |
1485 | /* USB 3.0 hubs don't have a TT */ | |
1486 | break; | |
1487 | default: | |
1488 | dev_dbg(hub_dev, "Unrecognized hub protocol %d\n", | |
1489 | hdev->descriptor.bDeviceProtocol); | |
1490 | break; | |
1da177e4 LT |
1491 | } |
1492 | ||
e09711ae | 1493 | /* Note 8 FS bit times == (8 bits / 12000000 bps) ~= 666ns */ |
74ad9bd2 | 1494 | switch (wHubCharacteristics & HUB_CHAR_TTTT) { |
469271f8 MB |
1495 | case HUB_TTTT_8_BITS: |
1496 | if (hdev->descriptor.bDeviceProtocol != 0) { | |
1497 | hub->tt.think_time = 666; | |
e09711ae DB |
1498 | dev_dbg(hub_dev, "TT requires at most %d " |
1499 | "FS bit times (%d ns)\n", | |
469271f8 MB |
1500 | 8, hub->tt.think_time); |
1501 | } | |
1502 | break; | |
1503 | case HUB_TTTT_16_BITS: | |
1504 | hub->tt.think_time = 666 * 2; | |
1505 | dev_dbg(hub_dev, "TT requires at most %d " | |
1506 | "FS bit times (%d ns)\n", | |
1507 | 16, hub->tt.think_time); | |
1508 | break; | |
1509 | case HUB_TTTT_24_BITS: | |
1510 | hub->tt.think_time = 666 * 3; | |
1511 | dev_dbg(hub_dev, "TT requires at most %d " | |
1512 | "FS bit times (%d ns)\n", | |
1513 | 24, hub->tt.think_time); | |
1514 | break; | |
1515 | case HUB_TTTT_32_BITS: | |
1516 | hub->tt.think_time = 666 * 4; | |
1517 | dev_dbg(hub_dev, "TT requires at most %d " | |
1518 | "FS bit times (%d ns)\n", | |
1519 | 32, hub->tt.think_time); | |
1520 | break; | |
1da177e4 LT |
1521 | } |
1522 | ||
1523 | /* probe() zeroes hub->indicator[] */ | |
74ad9bd2 | 1524 | if (wHubCharacteristics & HUB_CHAR_PORTIND) { |
1da177e4 LT |
1525 | hub->has_indicators = 1; |
1526 | dev_dbg(hub_dev, "Port indicators are supported\n"); | |
1527 | } | |
1528 | ||
1529 | dev_dbg(hub_dev, "power on to power good time: %dms\n", | |
1530 | hub->descriptor->bPwrOn2PwrGood * 2); | |
1531 | ||
1532 | /* power budgeting mostly matters with bus-powered hubs, | |
1533 | * and battery-powered root hubs (may provide just 8 mA). | |
1534 | */ | |
1535 | ret = usb_get_status(hdev, USB_RECIP_DEVICE, 0, &hubstatus); | |
15b7336e | 1536 | if (ret) { |
1da177e4 LT |
1537 | message = "can't get hub status"; |
1538 | goto fail; | |
1539 | } | |
430ee58e | 1540 | hcd = bus_to_hcd(hdev->bus); |
7d35b929 | 1541 | if (hdev == hdev->bus->root_hub) { |
430ee58e SAS |
1542 | if (hcd->power_budget > 0) |
1543 | hdev->bus_mA = hcd->power_budget; | |
1544 | else | |
d8521afe | 1545 | hdev->bus_mA = full_load * maxchild; |
430ee58e SAS |
1546 | if (hdev->bus_mA >= full_load) |
1547 | hub->mA_per_port = full_load; | |
55c52718 AS |
1548 | else { |
1549 | hub->mA_per_port = hdev->bus_mA; | |
1550 | hub->limited_power = 1; | |
1551 | } | |
7d35b929 | 1552 | } else if ((hubstatus & (1 << USB_DEVICE_SELF_POWERED)) == 0) { |
430ee58e SAS |
1553 | int remaining = hdev->bus_mA - |
1554 | hub->descriptor->bHubContrCurrent; | |
1555 | ||
1da177e4 LT |
1556 | dev_dbg(hub_dev, "hub controller current requirement: %dmA\n", |
1557 | hub->descriptor->bHubContrCurrent); | |
55c52718 | 1558 | hub->limited_power = 1; |
55c52718 | 1559 | |
d8521afe | 1560 | if (remaining < maxchild * unit_load) |
430ee58e | 1561 | dev_warn(hub_dev, |
55c52718 AS |
1562 | "insufficient power available " |
1563 | "to use all downstream ports\n"); | |
430ee58e SAS |
1564 | hub->mA_per_port = unit_load; /* 7.2.1 */ |
1565 | ||
55c52718 AS |
1566 | } else { /* Self-powered external hub */ |
1567 | /* FIXME: What about battery-powered external hubs that | |
1568 | * provide less current per port? */ | |
430ee58e | 1569 | hub->mA_per_port = full_load; |
7d35b929 | 1570 | } |
430ee58e | 1571 | if (hub->mA_per_port < full_load) |
55c52718 AS |
1572 | dev_dbg(hub_dev, "%umA bus power budget for each child\n", |
1573 | hub->mA_per_port); | |
1da177e4 LT |
1574 | |
1575 | ret = hub_hub_status(hub, &hubstatus, &hubchange); | |
1576 | if (ret < 0) { | |
1577 | message = "can't get hub status"; | |
1578 | goto fail; | |
1579 | } | |
1580 | ||
1581 | /* local power status reports aren't always correct */ | |
1582 | if (hdev->actconfig->desc.bmAttributes & USB_CONFIG_ATT_SELFPOWER) | |
1583 | dev_dbg(hub_dev, "local power source is %s\n", | |
1584 | (hubstatus & HUB_STATUS_LOCAL_POWER) | |
1585 | ? "lost (inactive)" : "good"); | |
1586 | ||
74ad9bd2 | 1587 | if ((wHubCharacteristics & HUB_CHAR_OCPM) == 0) |
1da177e4 LT |
1588 | dev_dbg(hub_dev, "%sover-current condition exists\n", |
1589 | (hubstatus & HUB_STATUS_OVERCURRENT) ? "" : "no "); | |
1590 | ||
88fafff9 | 1591 | /* set up the interrupt endpoint |
1592 | * We use the EP's maxpacket size instead of (PORTS+1+7)/8 | |
1593 | * bytes as USB2.0[11.12.3] says because some hubs are known | |
1594 | * to send more data (and thus cause overflow). For root hubs, | |
1595 | * maxpktsize is defined in hcd.c's fake endpoint descriptors | |
1596 | * to be big enough for at least USB_MAXCHILDREN ports. */ | |
1da177e4 LT |
1597 | pipe = usb_rcvintpipe(hdev, endpoint->bEndpointAddress); |
1598 | maxp = usb_maxpacket(hdev, pipe, usb_pipeout(pipe)); | |
1599 | ||
1600 | if (maxp > sizeof(*hub->buffer)) | |
1601 | maxp = sizeof(*hub->buffer); | |
1602 | ||
1603 | hub->urb = usb_alloc_urb(0, GFP_KERNEL); | |
1604 | if (!hub->urb) { | |
1da177e4 LT |
1605 | ret = -ENOMEM; |
1606 | goto fail; | |
1607 | } | |
1608 | ||
1609 | usb_fill_int_urb(hub->urb, hdev, pipe, *hub->buffer, maxp, hub_irq, | |
1610 | hub, endpoint->bInterval); | |
1da177e4 LT |
1611 | |
1612 | /* maybe cycle the hub leds */ | |
1613 | if (hub->has_indicators && blinkenlights) | |
469271f8 | 1614 | hub->indicator[0] = INDICATOR_CYCLE; |
1da177e4 | 1615 | |
d8521afe DW |
1616 | mutex_lock(&usb_port_peer_mutex); |
1617 | for (i = 0; i < maxchild; i++) { | |
e58547eb KM |
1618 | ret = usb_hub_create_port_device(hub, i + 1); |
1619 | if (ret < 0) { | |
fa2a9566 LT |
1620 | dev_err(hub->intfdev, |
1621 | "couldn't create port%d device.\n", i + 1); | |
d8521afe | 1622 | break; |
e58547eb KM |
1623 | } |
1624 | } | |
d8521afe | 1625 | hdev->maxchild = i; |
e3d10505 DW |
1626 | for (i = 0; i < hdev->maxchild; i++) { |
1627 | struct usb_port *port_dev = hub->ports[i]; | |
1628 | ||
1629 | pm_runtime_put(&port_dev->dev); | |
1630 | } | |
1631 | ||
d8521afe DW |
1632 | mutex_unlock(&usb_port_peer_mutex); |
1633 | if (ret < 0) | |
1634 | goto fail; | |
fa2a9566 | 1635 | |
37ebb549 | 1636 | /* Update the HCD's internal representation of this hub before hub_wq |
e3d95580 DW |
1637 | * starts getting port status changes for devices under the hub. |
1638 | */ | |
1639 | if (hcd->driver->update_hub_device) { | |
1640 | ret = hcd->driver->update_hub_device(hcd, hdev, | |
1641 | &hub->tt, GFP_KERNEL); | |
1642 | if (ret < 0) { | |
1643 | message = "can't update HCD hub info"; | |
1644 | goto fail; | |
1645 | } | |
1646 | } | |
1647 | ||
d2123fd9 LT |
1648 | usb_hub_adjust_deviceremovable(hdev, hub->descriptor); |
1649 | ||
f2835219 | 1650 | hub_activate(hub, HUB_INIT); |
1da177e4 LT |
1651 | return 0; |
1652 | ||
1653 | fail: | |
17248569 | 1654 | dev_err(hub_dev, "config failed, %s (err %d)\n", |
1da177e4 LT |
1655 | message, ret); |
1656 | /* hub_disconnect() frees urb and descriptor */ | |
1657 | return ret; | |
1658 | } | |
1659 | ||
e8054854 AS |
1660 | static void hub_release(struct kref *kref) |
1661 | { | |
1662 | struct usb_hub *hub = container_of(kref, struct usb_hub, kref); | |
1663 | ||
5d14f323 | 1664 | usb_put_dev(hub->hdev); |
e8054854 AS |
1665 | usb_put_intf(to_usb_interface(hub->intfdev)); |
1666 | kfree(hub); | |
1667 | } | |
1668 | ||
1da177e4 LT |
1669 | static unsigned highspeed_hubs; |
1670 | ||
1671 | static void hub_disconnect(struct usb_interface *intf) | |
1672 | { | |
8816230e | 1673 | struct usb_hub *hub = usb_get_intfdata(intf); |
fa286188 | 1674 | struct usb_device *hdev = interface_to_usbdev(intf); |
543d7784 | 1675 | int port1; |
fa2a9566 | 1676 | |
32a69589 PM |
1677 | /* |
1678 | * Stop adding new hub events. We do not want to block here and thus | |
1679 | * will not try to remove any pending work item. | |
1680 | */ | |
e8054854 | 1681 | hub->disconnected = 1; |
1da177e4 | 1682 | |
7de18d8b AS |
1683 | /* Disconnect all children and quiesce the hub */ |
1684 | hub->error = 0; | |
4330354f | 1685 | hub_quiesce(hub, HUB_DISCONNECT); |
7de18d8b | 1686 | |
d8521afe DW |
1687 | mutex_lock(&usb_port_peer_mutex); |
1688 | ||
543d7784 AS |
1689 | /* Avoid races with recursively_mark_NOTATTACHED() */ |
1690 | spin_lock_irq(&device_state_lock); | |
1691 | port1 = hdev->maxchild; | |
1692 | hdev->maxchild = 0; | |
1693 | usb_set_intfdata(intf, NULL); | |
1694 | spin_unlock_irq(&device_state_lock); | |
1f2235b8 | 1695 | |
543d7784 AS |
1696 | for (; port1 > 0; --port1) |
1697 | usb_hub_remove_port_device(hub, port1); | |
1da177e4 | 1698 | |
d8521afe DW |
1699 | mutex_unlock(&usb_port_peer_mutex); |
1700 | ||
e8054854 | 1701 | if (hub->hdev->speed == USB_SPEED_HIGH) |
1da177e4 LT |
1702 | highspeed_hubs--; |
1703 | ||
1da177e4 | 1704 | usb_free_urb(hub->urb); |
fa2a9566 | 1705 | kfree(hub->ports); |
1bc3c9e1 | 1706 | kfree(hub->descriptor); |
1bc3c9e1 | 1707 | kfree(hub->status); |
d697cdda | 1708 | kfree(hub->buffer); |
1da177e4 | 1709 | |
971fcd49 | 1710 | pm_suspend_ignore_children(&intf->dev, false); |
e8054854 | 1711 | kref_put(&hub->kref, hub_release); |
1da177e4 LT |
1712 | } |
1713 | ||
1714 | static int hub_probe(struct usb_interface *intf, const struct usb_device_id *id) | |
1715 | { | |
1716 | struct usb_host_interface *desc; | |
1717 | struct usb_endpoint_descriptor *endpoint; | |
1718 | struct usb_device *hdev; | |
1719 | struct usb_hub *hub; | |
1720 | ||
1721 | desc = intf->cur_altsetting; | |
1722 | hdev = interface_to_usbdev(intf); | |
1723 | ||
596d789a ML |
1724 | /* |
1725 | * Set default autosuspend delay as 0 to speedup bus suspend, | |
1726 | * based on the below considerations: | |
1727 | * | |
1728 | * - Unlike other drivers, the hub driver does not rely on the | |
1729 | * autosuspend delay to provide enough time to handle a wakeup | |
1730 | * event, and the submitted status URB is just to check future | |
1731 | * change on hub downstream ports, so it is safe to do it. | |
1732 | * | |
1733 | * - The patch might cause one or more auto supend/resume for | |
1734 | * below very rare devices when they are plugged into hub | |
1735 | * first time: | |
1736 | * | |
1737 | * devices having trouble initializing, and disconnect | |
1738 | * themselves from the bus and then reconnect a second | |
1739 | * or so later | |
1740 | * | |
1741 | * devices just for downloading firmware, and disconnects | |
1742 | * themselves after completing it | |
1743 | * | |
1744 | * For these quite rare devices, their drivers may change the | |
1745 | * autosuspend delay of their parent hub in the probe() to one | |
1746 | * appropriate value to avoid the subtle problem if someone | |
1747 | * does care it. | |
1748 | * | |
1749 | * - The patch may cause one or more auto suspend/resume on | |
1750 | * hub during running 'lsusb', but it is probably too | |
1751 | * infrequent to worry about. | |
1752 | * | |
1753 | * - Change autosuspend delay of hub can avoid unnecessary auto | |
1754 | * suspend timer for hub, also may decrease power consumption | |
1755 | * of USB bus. | |
bdd405d2 RQ |
1756 | * |
1757 | * - If user has indicated to prevent autosuspend by passing | |
1758 | * usbcore.autosuspend = -1 then keep autosuspend disabled. | |
596d789a | 1759 | */ |
ceb6c9c8 | 1760 | #ifdef CONFIG_PM |
bdd405d2 RQ |
1761 | if (hdev->dev.power.autosuspend_delay >= 0) |
1762 | pm_runtime_set_autosuspend_delay(&hdev->dev, 0); | |
a9ef803d | 1763 | #endif |
596d789a | 1764 | |
8ef42ddd AS |
1765 | /* |
1766 | * Hubs have proper suspend/resume support, except for root hubs | |
1767 | * where the controller driver doesn't have bus_suspend and | |
1768 | * bus_resume methods. | |
1769 | */ | |
1770 | if (hdev->parent) { /* normal device */ | |
1771 | usb_enable_autosuspend(hdev); | |
1772 | } else { /* root hub */ | |
1773 | const struct hc_driver *drv = bus_to_hcd(hdev->bus)->driver; | |
1774 | ||
1775 | if (drv->bus_suspend && drv->bus_resume) | |
1776 | usb_enable_autosuspend(hdev); | |
1777 | } | |
088f7fec | 1778 | |
38f3ad5e | 1779 | if (hdev->level == MAX_TOPO_LEVEL) { |
b9cef6c3 WF |
1780 | dev_err(&intf->dev, |
1781 | "Unsupported bus topology: hub nested too deep\n"); | |
38f3ad5e FB |
1782 | return -E2BIG; |
1783 | } | |
1784 | ||
89ccbdc9 DB |
1785 | #ifdef CONFIG_USB_OTG_BLACKLIST_HUB |
1786 | if (hdev->parent) { | |
1787 | dev_warn(&intf->dev, "ignoring external hub\n"); | |
1788 | return -ENODEV; | |
1789 | } | |
1790 | #endif | |
1791 | ||
1da177e4 LT |
1792 | /* Some hubs have a subclass of 1, which AFAICT according to the */ |
1793 | /* specs is not defined, but it works */ | |
1794 | if ((desc->desc.bInterfaceSubClass != 0) && | |
1795 | (desc->desc.bInterfaceSubClass != 1)) { | |
1796 | descriptor_error: | |
17248569 | 1797 | dev_err(&intf->dev, "bad descriptor, ignoring hub\n"); |
1da177e4 LT |
1798 | return -EIO; |
1799 | } | |
1800 | ||
1801 | /* Multiple endpoints? What kind of mutant ninja-hub is this? */ | |
1802 | if (desc->desc.bNumEndpoints != 1) | |
1803 | goto descriptor_error; | |
1804 | ||
1805 | endpoint = &desc->endpoint[0].desc; | |
1806 | ||
fbf81c29 LFC |
1807 | /* If it's not an interrupt in endpoint, we'd better punt! */ |
1808 | if (!usb_endpoint_is_int_in(endpoint)) | |
1da177e4 LT |
1809 | goto descriptor_error; |
1810 | ||
1811 | /* We found a hub */ | |
17248569 | 1812 | dev_info(&intf->dev, "USB hub found\n"); |
1da177e4 | 1813 | |
0a1ef3b5 | 1814 | hub = kzalloc(sizeof(*hub), GFP_KERNEL); |
1da177e4 | 1815 | if (!hub) { |
17248569 | 1816 | dev_dbg(&intf->dev, "couldn't kmalloc hub struct\n"); |
1da177e4 LT |
1817 | return -ENOMEM; |
1818 | } | |
1819 | ||
e8054854 | 1820 | kref_init(&hub->kref); |
1da177e4 LT |
1821 | hub->intfdev = &intf->dev; |
1822 | hub->hdev = hdev; | |
c4028958 | 1823 | INIT_DELAYED_WORK(&hub->leds, led_work); |
8520f380 | 1824 | INIT_DELAYED_WORK(&hub->init_work, NULL); |
32a69589 | 1825 | INIT_WORK(&hub->events, hub_event); |
e8054854 | 1826 | usb_get_intf(intf); |
5d14f323 | 1827 | usb_get_dev(hdev); |
1da177e4 | 1828 | |
17248569 | 1829 | usb_set_intfdata(intf, hub); |
40f122f3 | 1830 | intf->needs_remote_wakeup = 1; |
971fcd49 | 1831 | pm_suspend_ignore_children(&intf->dev, true); |
1da177e4 LT |
1832 | |
1833 | if (hdev->speed == USB_SPEED_HIGH) | |
1834 | highspeed_hubs++; | |
1835 | ||
e6f30dea ML |
1836 | if (id->driver_info & HUB_QUIRK_CHECK_PORT_AUTOSUSPEND) |
1837 | hub->quirk_check_port_auto_suspend = 1; | |
1838 | ||
1da177e4 LT |
1839 | if (hub_configure(hub, endpoint) >= 0) |
1840 | return 0; | |
1841 | ||
17248569 | 1842 | hub_disconnect(intf); |
1da177e4 LT |
1843 | return -ENODEV; |
1844 | } | |
1845 | ||
1846 | static int | |
1847 | hub_ioctl(struct usb_interface *intf, unsigned int code, void *user_data) | |
1848 | { | |
17248569 | 1849 | struct usb_device *hdev = interface_to_usbdev(intf); |
ad493e5e | 1850 | struct usb_hub *hub = usb_hub_to_struct_hub(hdev); |
1da177e4 LT |
1851 | |
1852 | /* assert ifno == 0 (part of hub spec) */ | |
1853 | switch (code) { | |
1854 | case USBDEVFS_HUB_PORTINFO: { | |
1855 | struct usbdevfs_hub_portinfo *info = user_data; | |
1856 | int i; | |
1857 | ||
1858 | spin_lock_irq(&device_state_lock); | |
1859 | if (hdev->devnum <= 0) | |
1860 | info->nports = 0; | |
1861 | else { | |
1862 | info->nports = hdev->maxchild; | |
1863 | for (i = 0; i < info->nports; i++) { | |
ff823c79 | 1864 | if (hub->ports[i]->child == NULL) |
1da177e4 LT |
1865 | info->port[i] = 0; |
1866 | else | |
1867 | info->port[i] = | |
ff823c79 | 1868 | hub->ports[i]->child->devnum; |
1da177e4 LT |
1869 | } |
1870 | } | |
1871 | spin_unlock_irq(&device_state_lock); | |
1872 | ||
1873 | return info->nports + 1; | |
1874 | } | |
1875 | ||
1876 | default: | |
1877 | return -ENOSYS; | |
1878 | } | |
1879 | } | |
1880 | ||
7cbe5dca AS |
1881 | /* |
1882 | * Allow user programs to claim ports on a hub. When a device is attached | |
1883 | * to one of these "claimed" ports, the program will "own" the device. | |
1884 | */ | |
1885 | static int find_port_owner(struct usb_device *hdev, unsigned port1, | |
9b6f0c4b | 1886 | struct usb_dev_state ***ppowner) |
7cbe5dca | 1887 | { |
41341261 MN |
1888 | struct usb_hub *hub = usb_hub_to_struct_hub(hdev); |
1889 | ||
7cbe5dca AS |
1890 | if (hdev->state == USB_STATE_NOTATTACHED) |
1891 | return -ENODEV; | |
1892 | if (port1 == 0 || port1 > hdev->maxchild) | |
1893 | return -EINVAL; | |
1894 | ||
41341261 | 1895 | /* Devices not managed by the hub driver |
7cbe5dca AS |
1896 | * will always have maxchild equal to 0. |
1897 | */ | |
41341261 | 1898 | *ppowner = &(hub->ports[port1 - 1]->port_owner); |
7cbe5dca AS |
1899 | return 0; |
1900 | } | |
1901 | ||
1902 | /* In the following three functions, the caller must hold hdev's lock */ | |
336c5c31 | 1903 | int usb_hub_claim_port(struct usb_device *hdev, unsigned port1, |
9b6f0c4b | 1904 | struct usb_dev_state *owner) |
7cbe5dca AS |
1905 | { |
1906 | int rc; | |
9b6f0c4b | 1907 | struct usb_dev_state **powner; |
7cbe5dca AS |
1908 | |
1909 | rc = find_port_owner(hdev, port1, &powner); | |
1910 | if (rc) | |
1911 | return rc; | |
1912 | if (*powner) | |
1913 | return -EBUSY; | |
1914 | *powner = owner; | |
1915 | return rc; | |
1916 | } | |
6080cd0e | 1917 | EXPORT_SYMBOL_GPL(usb_hub_claim_port); |
7cbe5dca | 1918 | |
336c5c31 | 1919 | int usb_hub_release_port(struct usb_device *hdev, unsigned port1, |
9b6f0c4b | 1920 | struct usb_dev_state *owner) |
7cbe5dca AS |
1921 | { |
1922 | int rc; | |
9b6f0c4b | 1923 | struct usb_dev_state **powner; |
7cbe5dca AS |
1924 | |
1925 | rc = find_port_owner(hdev, port1, &powner); | |
1926 | if (rc) | |
1927 | return rc; | |
1928 | if (*powner != owner) | |
1929 | return -ENOENT; | |
1930 | *powner = NULL; | |
1931 | return rc; | |
1932 | } | |
6080cd0e | 1933 | EXPORT_SYMBOL_GPL(usb_hub_release_port); |
7cbe5dca | 1934 | |
9b6f0c4b | 1935 | void usb_hub_release_all_ports(struct usb_device *hdev, struct usb_dev_state *owner) |
7cbe5dca | 1936 | { |
ad493e5e | 1937 | struct usb_hub *hub = usb_hub_to_struct_hub(hdev); |
7cbe5dca | 1938 | int n; |
7cbe5dca | 1939 | |
fa2a9566 LT |
1940 | for (n = 0; n < hdev->maxchild; n++) { |
1941 | if (hub->ports[n]->port_owner == owner) | |
1942 | hub->ports[n]->port_owner = NULL; | |
7cbe5dca | 1943 | } |
fa2a9566 | 1944 | |
7cbe5dca AS |
1945 | } |
1946 | ||
1947 | /* The caller must hold udev's lock */ | |
1948 | bool usb_device_is_owned(struct usb_device *udev) | |
1949 | { | |
1950 | struct usb_hub *hub; | |
1951 | ||
1952 | if (udev->state == USB_STATE_NOTATTACHED || !udev->parent) | |
1953 | return false; | |
ad493e5e | 1954 | hub = usb_hub_to_struct_hub(udev->parent); |
fa2a9566 | 1955 | return !!hub->ports[udev->portnum - 1]->port_owner; |
7cbe5dca AS |
1956 | } |
1957 | ||
1da177e4 LT |
1958 | static void recursively_mark_NOTATTACHED(struct usb_device *udev) |
1959 | { | |
ad493e5e | 1960 | struct usb_hub *hub = usb_hub_to_struct_hub(udev); |
1da177e4 LT |
1961 | int i; |
1962 | ||
1963 | for (i = 0; i < udev->maxchild; ++i) { | |
ff823c79 LT |
1964 | if (hub->ports[i]->child) |
1965 | recursively_mark_NOTATTACHED(hub->ports[i]->child); | |
1da177e4 | 1966 | } |
9bbdf1e0 | 1967 | if (udev->state == USB_STATE_SUSPENDED) |
15123006 | 1968 | udev->active_duration -= jiffies; |
1da177e4 LT |
1969 | udev->state = USB_STATE_NOTATTACHED; |
1970 | } | |
1971 | ||
1972 | /** | |
1973 | * usb_set_device_state - change a device's current state (usbcore, hcds) | |
1974 | * @udev: pointer to device whose state should be changed | |
1975 | * @new_state: new state value to be stored | |
1976 | * | |
1977 | * udev->state is _not_ fully protected by the device lock. Although | |
1978 | * most transitions are made only while holding the lock, the state can | |
1979 | * can change to USB_STATE_NOTATTACHED at almost any time. This | |
1980 | * is so that devices can be marked as disconnected as soon as possible, | |
1981 | * without having to wait for any semaphores to be released. As a result, | |
1982 | * all changes to any device's state must be protected by the | |
1983 | * device_state_lock spinlock. | |
1984 | * | |
1985 | * Once a device has been added to the device tree, all changes to its state | |
1986 | * should be made using this routine. The state should _not_ be set directly. | |
1987 | * | |
1988 | * If udev->state is already USB_STATE_NOTATTACHED then no change is made. | |
1989 | * Otherwise udev->state is set to new_state, and if new_state is | |
1990 | * USB_STATE_NOTATTACHED then all of udev's descendants' states are also set | |
1991 | * to USB_STATE_NOTATTACHED. | |
1992 | */ | |
1993 | void usb_set_device_state(struct usb_device *udev, | |
1994 | enum usb_device_state new_state) | |
1995 | { | |
1996 | unsigned long flags; | |
4681b171 | 1997 | int wakeup = -1; |
1da177e4 LT |
1998 | |
1999 | spin_lock_irqsave(&device_state_lock, flags); | |
2000 | if (udev->state == USB_STATE_NOTATTACHED) | |
2001 | ; /* do nothing */ | |
b94dc6b5 | 2002 | else if (new_state != USB_STATE_NOTATTACHED) { |
fb669cc0 DB |
2003 | |
2004 | /* root hub wakeup capabilities are managed out-of-band | |
2005 | * and may involve silicon errata ... ignore them here. | |
2006 | */ | |
2007 | if (udev->parent) { | |
645daaab AS |
2008 | if (udev->state == USB_STATE_SUSPENDED |
2009 | || new_state == USB_STATE_SUSPENDED) | |
2010 | ; /* No change to wakeup settings */ | |
2011 | else if (new_state == USB_STATE_CONFIGURED) | |
ddbe1fca LB |
2012 | wakeup = (udev->quirks & |
2013 | USB_QUIRK_IGNORE_REMOTE_WAKEUP) ? 0 : | |
2014 | udev->actconfig->desc.bmAttributes & | |
2015 | USB_CONFIG_ATT_WAKEUP; | |
645daaab | 2016 | else |
4681b171 | 2017 | wakeup = 0; |
fb669cc0 | 2018 | } |
15123006 SS |
2019 | if (udev->state == USB_STATE_SUSPENDED && |
2020 | new_state != USB_STATE_SUSPENDED) | |
2021 | udev->active_duration -= jiffies; | |
2022 | else if (new_state == USB_STATE_SUSPENDED && | |
2023 | udev->state != USB_STATE_SUSPENDED) | |
2024 | udev->active_duration += jiffies; | |
645daaab | 2025 | udev->state = new_state; |
b94dc6b5 | 2026 | } else |
1da177e4 LT |
2027 | recursively_mark_NOTATTACHED(udev); |
2028 | spin_unlock_irqrestore(&device_state_lock, flags); | |
4681b171 RW |
2029 | if (wakeup >= 0) |
2030 | device_set_wakeup_capable(&udev->dev, wakeup); | |
1da177e4 | 2031 | } |
6da9c990 | 2032 | EXPORT_SYMBOL_GPL(usb_set_device_state); |
1da177e4 | 2033 | |
8af548dc | 2034 | /* |
3b29b68b AS |
2035 | * Choose a device number. |
2036 | * | |
2037 | * Device numbers are used as filenames in usbfs. On USB-1.1 and | |
2038 | * USB-2.0 buses they are also used as device addresses, however on | |
2039 | * USB-3.0 buses the address is assigned by the controller hardware | |
2040 | * and it usually is not the same as the device number. | |
2041 | * | |
8af548dc IPG |
2042 | * WUSB devices are simple: they have no hubs behind, so the mapping |
2043 | * device <-> virtual port number becomes 1:1. Why? to simplify the | |
2044 | * life of the device connection logic in | |
2045 | * drivers/usb/wusbcore/devconnect.c. When we do the initial secret | |
2046 | * handshake we need to assign a temporary address in the unauthorized | |
2047 | * space. For simplicity we use the first virtual port number found to | |
2048 | * be free [drivers/usb/wusbcore/devconnect.c:wusbhc_devconnect_ack()] | |
2049 | * and that becomes it's address [X < 128] or its unauthorized address | |
2050 | * [X | 0x80]. | |
2051 | * | |
2052 | * We add 1 as an offset to the one-based USB-stack port number | |
2053 | * (zero-based wusb virtual port index) for two reasons: (a) dev addr | |
2054 | * 0 is reserved by USB for default address; (b) Linux's USB stack | |
2055 | * uses always #1 for the root hub of the controller. So USB stack's | |
2056 | * port #1, which is wusb virtual-port #0 has address #2. | |
c6515272 SS |
2057 | * |
2058 | * Devices connected under xHCI are not as simple. The host controller | |
2059 | * supports virtualization, so the hardware assigns device addresses and | |
2060 | * the HCD must setup data structures before issuing a set address | |
2061 | * command to the hardware. | |
8af548dc | 2062 | */ |
3b29b68b | 2063 | static void choose_devnum(struct usb_device *udev) |
1da177e4 LT |
2064 | { |
2065 | int devnum; | |
2066 | struct usb_bus *bus = udev->bus; | |
2067 | ||
638139eb PM |
2068 | /* be safe when more hub events are proceed in parallel */ |
2069 | mutex_lock(&bus->usb_address0_mutex); | |
8af548dc IPG |
2070 | if (udev->wusb) { |
2071 | devnum = udev->portnum + 1; | |
2072 | BUG_ON(test_bit(devnum, bus->devmap.devicemap)); | |
2073 | } else { | |
2074 | /* Try to allocate the next devnum beginning at | |
2075 | * bus->devnum_next. */ | |
2076 | devnum = find_next_zero_bit(bus->devmap.devicemap, 128, | |
2077 | bus->devnum_next); | |
2078 | if (devnum >= 128) | |
2079 | devnum = find_next_zero_bit(bus->devmap.devicemap, | |
2080 | 128, 1); | |
469271f8 | 2081 | bus->devnum_next = (devnum >= 127 ? 1 : devnum + 1); |
8af548dc | 2082 | } |
1da177e4 LT |
2083 | if (devnum < 128) { |
2084 | set_bit(devnum, bus->devmap.devicemap); | |
2085 | udev->devnum = devnum; | |
2086 | } | |
638139eb | 2087 | mutex_unlock(&bus->usb_address0_mutex); |
1da177e4 LT |
2088 | } |
2089 | ||
3b29b68b | 2090 | static void release_devnum(struct usb_device *udev) |
1da177e4 LT |
2091 | { |
2092 | if (udev->devnum > 0) { | |
2093 | clear_bit(udev->devnum, udev->bus->devmap.devicemap); | |
2094 | udev->devnum = -1; | |
2095 | } | |
2096 | } | |
2097 | ||
3b29b68b | 2098 | static void update_devnum(struct usb_device *udev, int devnum) |
4953d141 DV |
2099 | { |
2100 | /* The address for a WUSB device is managed by wusbcore. */ | |
2101 | if (!udev->wusb) | |
2102 | udev->devnum = devnum; | |
2103 | } | |
2104 | ||
f7410ced HX |
2105 | static void hub_free_dev(struct usb_device *udev) |
2106 | { | |
2107 | struct usb_hcd *hcd = bus_to_hcd(udev->bus); | |
2108 | ||
2109 | /* Root hubs aren't real devices, so don't free HCD resources */ | |
2110 | if (hcd->driver->free_dev && udev->parent) | |
2111 | hcd->driver->free_dev(hcd, udev); | |
2112 | } | |
2113 | ||
7027df36 DW |
2114 | static void hub_disconnect_children(struct usb_device *udev) |
2115 | { | |
2116 | struct usb_hub *hub = usb_hub_to_struct_hub(udev); | |
2117 | int i; | |
2118 | ||
2119 | /* Free up all the children before we remove this device */ | |
2120 | for (i = 0; i < udev->maxchild; i++) { | |
2121 | if (hub->ports[i]->child) | |
2122 | usb_disconnect(&hub->ports[i]->child); | |
2123 | } | |
2124 | } | |
2125 | ||
1da177e4 LT |
2126 | /** |
2127 | * usb_disconnect - disconnect a device (usbcore-internal) | |
2128 | * @pdev: pointer to device being disconnected | |
2129 | * Context: !in_interrupt () | |
2130 | * | |
2131 | * Something got disconnected. Get rid of it and all of its children. | |
2132 | * | |
2133 | * If *pdev is a normal device then the parent hub must already be locked. | |
db8f2aa3 BH |
2134 | * If *pdev is a root hub then the caller must hold the usb_bus_list_lock, |
2135 | * which protects the set of root hubs as well as the list of buses. | |
1da177e4 LT |
2136 | * |
2137 | * Only hub drivers (including virtual root hub drivers for host | |
2138 | * controllers) should ever call this. | |
2139 | * | |
2140 | * This call is synchronous, and may not be used in an interrupt context. | |
2141 | */ | |
2142 | void usb_disconnect(struct usb_device **pdev) | |
2143 | { | |
7027df36 DW |
2144 | struct usb_port *port_dev = NULL; |
2145 | struct usb_device *udev = *pdev; | |
5b1dc209 PC |
2146 | struct usb_hub *hub = NULL; |
2147 | int port1 = 1; | |
1da177e4 | 2148 | |
1da177e4 LT |
2149 | /* mark the device as inactive, so any further urb submissions for |
2150 | * this device (and any of its children) will fail immediately. | |
25985edc | 2151 | * this quiesces everything except pending urbs. |
1da177e4 LT |
2152 | */ |
2153 | usb_set_device_state(udev, USB_STATE_NOTATTACHED); | |
3b29b68b AS |
2154 | dev_info(&udev->dev, "USB disconnect, device number %d\n", |
2155 | udev->devnum); | |
1da177e4 | 2156 | |
9ad3d6cc AS |
2157 | usb_lock_device(udev); |
2158 | ||
7027df36 | 2159 | hub_disconnect_children(udev); |
1da177e4 LT |
2160 | |
2161 | /* deallocate hcd/hardware state ... nuking all pending urbs and | |
2162 | * cleaning up all state associated with the current configuration | |
2163 | * so that the hardware is now fully quiesced. | |
2164 | */ | |
17248569 | 2165 | dev_dbg(&udev->dev, "unregistering device\n"); |
1da177e4 | 2166 | usb_disable_device(udev, 0); |
cde217a5 | 2167 | usb_hcd_synchronize_unlinks(udev); |
1da177e4 | 2168 | |
fde26380 | 2169 | if (udev->parent) { |
7027df36 DW |
2170 | port1 = udev->portnum; |
2171 | hub = usb_hub_to_struct_hub(udev->parent); | |
2172 | port_dev = hub->ports[port1 - 1]; | |
fde26380 LT |
2173 | |
2174 | sysfs_remove_link(&udev->dev.kobj, "port"); | |
2175 | sysfs_remove_link(&port_dev->dev.kobj, "device"); | |
971fcd49 | 2176 | |
7027df36 DW |
2177 | /* |
2178 | * As usb_port_runtime_resume() de-references udev, make | |
2179 | * sure no resumes occur during removal | |
2180 | */ | |
2181 | if (!test_and_set_bit(port1, hub->child_usage_bits)) | |
2182 | pm_runtime_get_sync(&port_dev->dev); | |
fde26380 LT |
2183 | } |
2184 | ||
3b23dd6f | 2185 | usb_remove_ep_devs(&udev->ep0); |
782da727 AS |
2186 | usb_unlock_device(udev); |
2187 | ||
2188 | /* Unregister the device. The device driver is responsible | |
3b23dd6f AS |
2189 | * for de-configuring the device and invoking the remove-device |
2190 | * notifier chain (used by usbfs and possibly others). | |
782da727 AS |
2191 | */ |
2192 | device_del(&udev->dev); | |
3099e75a | 2193 | |
782da727 | 2194 | /* Free the device number and delete the parent's children[] |
1da177e4 LT |
2195 | * (or root_hub) pointer. |
2196 | */ | |
3b29b68b | 2197 | release_devnum(udev); |
1da177e4 LT |
2198 | |
2199 | /* Avoid races with recursively_mark_NOTATTACHED() */ | |
2200 | spin_lock_irq(&device_state_lock); | |
2201 | *pdev = NULL; | |
2202 | spin_unlock_irq(&device_state_lock); | |
2203 | ||
7027df36 DW |
2204 | if (port_dev && test_and_clear_bit(port1, hub->child_usage_bits)) |
2205 | pm_runtime_put(&port_dev->dev); | |
2206 | ||
f7410ced HX |
2207 | hub_free_dev(udev); |
2208 | ||
782da727 | 2209 | put_device(&udev->dev); |
1da177e4 LT |
2210 | } |
2211 | ||
f2a383e4 | 2212 | #ifdef CONFIG_USB_ANNOUNCE_NEW_DEVICES |
1da177e4 LT |
2213 | static void show_string(struct usb_device *udev, char *id, char *string) |
2214 | { | |
2215 | if (!string) | |
2216 | return; | |
f2ec522e | 2217 | dev_info(&udev->dev, "%s: %s\n", id, string); |
1da177e4 LT |
2218 | } |
2219 | ||
f2a383e4 GKH |
2220 | static void announce_device(struct usb_device *udev) |
2221 | { | |
2222 | dev_info(&udev->dev, "New USB device found, idVendor=%04x, idProduct=%04x\n", | |
2223 | le16_to_cpu(udev->descriptor.idVendor), | |
2224 | le16_to_cpu(udev->descriptor.idProduct)); | |
b9cef6c3 WF |
2225 | dev_info(&udev->dev, |
2226 | "New USB device strings: Mfr=%d, Product=%d, SerialNumber=%d\n", | |
f2a383e4 GKH |
2227 | udev->descriptor.iManufacturer, |
2228 | udev->descriptor.iProduct, | |
2229 | udev->descriptor.iSerialNumber); | |
2230 | show_string(udev, "Product", udev->product); | |
2231 | show_string(udev, "Manufacturer", udev->manufacturer); | |
2232 | show_string(udev, "SerialNumber", udev->serial); | |
2233 | } | |
1da177e4 | 2234 | #else |
f2a383e4 | 2235 | static inline void announce_device(struct usb_device *udev) { } |
1da177e4 LT |
2236 | #endif |
2237 | ||
1da177e4 | 2238 | |
3ede760f | 2239 | /** |
8d8558d1 | 2240 | * usb_enumerate_device_otg - FIXME (usbcore-internal) |
3ede760f ON |
2241 | * @udev: newly addressed device (in ADDRESS state) |
2242 | * | |
8d8558d1 | 2243 | * Finish enumeration for On-The-Go devices |
626f090c YB |
2244 | * |
2245 | * Return: 0 if successful. A negative error code otherwise. | |
3ede760f | 2246 | */ |
8d8558d1 | 2247 | static int usb_enumerate_device_otg(struct usb_device *udev) |
1da177e4 | 2248 | { |
d9d16e8a | 2249 | int err = 0; |
1da177e4 LT |
2250 | |
2251 | #ifdef CONFIG_USB_OTG | |
2252 | /* | |
2253 | * OTG-aware devices on OTG-capable root hubs may be able to use SRP, | |
2254 | * to wake us after we've powered off VBUS; and HNP, switching roles | |
2255 | * "host" to "peripheral". The OTG descriptor helps figure this out. | |
2256 | */ | |
2257 | if (!udev->bus->is_b_host | |
2258 | && udev->config | |
2259 | && udev->parent == udev->bus->root_hub) { | |
2eb5052e | 2260 | struct usb_otg_descriptor *desc = NULL; |
1da177e4 | 2261 | struct usb_bus *bus = udev->bus; |
7d2d641c | 2262 | unsigned port1 = udev->portnum; |
1da177e4 LT |
2263 | |
2264 | /* descriptor may appear anywhere in config */ | |
7d2d641c LJ |
2265 | err = __usb_get_extra_descriptor(udev->rawdescriptors[0], |
2266 | le16_to_cpu(udev->config[0].desc.wTotalLength), | |
2267 | USB_DT_OTG, (void **) &desc); | |
2268 | if (err || !(desc->bmAttributes & USB_OTG_HNP)) | |
2269 | return 0; | |
2270 | ||
2271 | dev_info(&udev->dev, "Dual-Role OTG device on %sHNP port\n", | |
2272 | (port1 == bus->otg_port) ? "" : "non-"); | |
2273 | ||
2274 | /* enable HNP before suspend, it's simpler */ | |
2275 | if (port1 == bus->otg_port) { | |
2276 | bus->b_hnp_enable = 1; | |
2277 | err = usb_control_msg(udev, | |
2278 | usb_sndctrlpipe(udev, 0), | |
2279 | USB_REQ_SET_FEATURE, 0, | |
2280 | USB_DEVICE_B_HNP_ENABLE, | |
2281 | 0, NULL, 0, | |
2282 | USB_CTRL_SET_TIMEOUT); | |
2283 | if (err < 0) { | |
2284 | /* | |
2285 | * OTG MESSAGE: report errors here, | |
2286 | * customize to match your product. | |
2287 | */ | |
2288 | dev_err(&udev->dev, "can't set HNP mode: %d\n", | |
2289 | err); | |
2290 | bus->b_hnp_enable = 0; | |
1da177e4 | 2291 | } |
7d2d641c LJ |
2292 | } else if (desc->bLength == sizeof |
2293 | (struct usb_otg_descriptor)) { | |
2294 | /* Set a_alt_hnp_support for legacy otg device */ | |
2295 | err = usb_control_msg(udev, | |
2296 | usb_sndctrlpipe(udev, 0), | |
2297 | USB_REQ_SET_FEATURE, 0, | |
2298 | USB_DEVICE_A_ALT_HNP_SUPPORT, | |
2299 | 0, NULL, 0, | |
2300 | USB_CTRL_SET_TIMEOUT); | |
2301 | if (err < 0) | |
2302 | dev_err(&udev->dev, | |
2303 | "set a_alt_hnp_support failed: %d\n", | |
2304 | err); | |
1da177e4 LT |
2305 | } |
2306 | } | |
1da177e4 | 2307 | #endif |
d9d16e8a IPG |
2308 | return err; |
2309 | } | |
2310 | ||
2311 | ||
2312 | /** | |
8d8558d1 | 2313 | * usb_enumerate_device - Read device configs/intfs/otg (usbcore-internal) |
d9d16e8a IPG |
2314 | * @udev: newly addressed device (in ADDRESS state) |
2315 | * | |
2316 | * This is only called by usb_new_device() and usb_authorize_device() | |
2317 | * and FIXME -- all comments that apply to them apply here wrt to | |
2318 | * environment. | |
2319 | * | |
2320 | * If the device is WUSB and not authorized, we don't attempt to read | |
2321 | * the string descriptors, as they will be errored out by the device | |
2322 | * until it has been authorized. | |
626f090c YB |
2323 | * |
2324 | * Return: 0 if successful. A negative error code otherwise. | |
d9d16e8a | 2325 | */ |
8d8558d1 | 2326 | static int usb_enumerate_device(struct usb_device *udev) |
d9d16e8a IPG |
2327 | { |
2328 | int err; | |
026f3fcb | 2329 | struct usb_hcd *hcd = bus_to_hcd(udev->bus); |
1da177e4 | 2330 | |
d9d16e8a IPG |
2331 | if (udev->config == NULL) { |
2332 | err = usb_get_configuration(udev); | |
2333 | if (err < 0) { | |
e9e88fb7 AS |
2334 | if (err != -ENODEV) |
2335 | dev_err(&udev->dev, "can't read configurations, error %d\n", | |
2336 | err); | |
80da2e0d | 2337 | return err; |
d9d16e8a IPG |
2338 | } |
2339 | } | |
83e83ecb TP |
2340 | |
2341 | /* read the standard strings and cache them if present */ | |
2342 | udev->product = usb_cache_string(udev, udev->descriptor.iProduct); | |
2343 | udev->manufacturer = usb_cache_string(udev, | |
2344 | udev->descriptor.iManufacturer); | |
2345 | udev->serial = usb_cache_string(udev, udev->descriptor.iSerialNumber); | |
2346 | ||
8d8558d1 | 2347 | err = usb_enumerate_device_otg(udev); |
80da2e0d LP |
2348 | if (err < 0) |
2349 | return err; | |
2350 | ||
026f3fcb | 2351 | if (IS_ENABLED(CONFIG_USB_OTG_WHITELIST) && hcd->tpl_support && |
e5a9d621 | 2352 | !is_targeted(udev)) { |
026f3fcb PC |
2353 | /* Maybe it can talk to us, though we can't talk to it. |
2354 | * (Includes HNP test device.) | |
2355 | */ | |
e5a9d621 PC |
2356 | if (IS_ENABLED(CONFIG_USB_OTG) && (udev->bus->b_hnp_enable |
2357 | || udev->bus->is_b_host)) { | |
026f3fcb PC |
2358 | err = usb_port_suspend(udev, PMSG_AUTO_SUSPEND); |
2359 | if (err < 0) | |
2360 | dev_dbg(&udev->dev, "HNP fail, %d\n", err); | |
2361 | } | |
2362 | return -ENOTSUPP; | |
2363 | } | |
2364 | ||
80da2e0d LP |
2365 | usb_detect_interface_quirks(udev); |
2366 | ||
2367 | return 0; | |
d9d16e8a IPG |
2368 | } |
2369 | ||
d35e70d5 MG |
2370 | static void set_usb_port_removable(struct usb_device *udev) |
2371 | { | |
2372 | struct usb_device *hdev = udev->parent; | |
2373 | struct usb_hub *hub; | |
2374 | u8 port = udev->portnum; | |
2375 | u16 wHubCharacteristics; | |
2376 | bool removable = true; | |
2377 | ||
2378 | if (!hdev) | |
2379 | return; | |
2380 | ||
ad493e5e | 2381 | hub = usb_hub_to_struct_hub(udev->parent); |
d35e70d5 | 2382 | |
92bfbf71 MG |
2383 | /* |
2384 | * If the platform firmware has provided information about a port, | |
2385 | * use that to determine whether it's removable. | |
2386 | */ | |
2387 | switch (hub->ports[udev->portnum - 1]->connect_type) { | |
2388 | case USB_PORT_CONNECT_TYPE_HOT_PLUG: | |
2389 | udev->removable = USB_DEVICE_REMOVABLE; | |
2390 | return; | |
2391 | case USB_PORT_CONNECT_TYPE_HARD_WIRED: | |
58339c2e | 2392 | case USB_PORT_NOT_USED: |
92bfbf71 MG |
2393 | udev->removable = USB_DEVICE_FIXED; |
2394 | return; | |
58339c2e MG |
2395 | default: |
2396 | break; | |
92bfbf71 MG |
2397 | } |
2398 | ||
2399 | /* | |
2400 | * Otherwise, check whether the hub knows whether a port is removable | |
2401 | * or not | |
2402 | */ | |
d35e70d5 MG |
2403 | wHubCharacteristics = le16_to_cpu(hub->descriptor->wHubCharacteristics); |
2404 | ||
2405 | if (!(wHubCharacteristics & HUB_CHAR_COMPOUND)) | |
2406 | return; | |
2407 | ||
2408 | if (hub_is_superspeed(hdev)) { | |
ca3c1539 LT |
2409 | if (le16_to_cpu(hub->descriptor->u.ss.DeviceRemovable) |
2410 | & (1 << port)) | |
d35e70d5 MG |
2411 | removable = false; |
2412 | } else { | |
2413 | if (hub->descriptor->u.hs.DeviceRemovable[port / 8] & (1 << (port % 8))) | |
2414 | removable = false; | |
2415 | } | |
2416 | ||
2417 | if (removable) | |
2418 | udev->removable = USB_DEVICE_REMOVABLE; | |
2419 | else | |
2420 | udev->removable = USB_DEVICE_FIXED; | |
a4204ff0 | 2421 | |
d35e70d5 | 2422 | } |
d9d16e8a IPG |
2423 | |
2424 | /** | |
2425 | * usb_new_device - perform initial device setup (usbcore-internal) | |
2426 | * @udev: newly addressed device (in ADDRESS state) | |
2427 | * | |
8d8558d1 AS |
2428 | * This is called with devices which have been detected but not fully |
2429 | * enumerated. The device descriptor is available, but not descriptors | |
d9d16e8a IPG |
2430 | * for any device configuration. The caller must have locked either |
2431 | * the parent hub (if udev is a normal device) or else the | |
2432 | * usb_bus_list_lock (if udev is a root hub). The parent's pointer to | |
2433 | * udev has already been installed, but udev is not yet visible through | |
2434 | * sysfs or other filesystem code. | |
2435 | * | |
d9d16e8a IPG |
2436 | * This call is synchronous, and may not be used in an interrupt context. |
2437 | * | |
2438 | * Only the hub driver or root-hub registrar should ever call this. | |
626f090c YB |
2439 | * |
2440 | * Return: Whether the device is configured properly or not. Zero if the | |
2441 | * interface was registered with the driver core; else a negative errno | |
2442 | * value. | |
2443 | * | |
d9d16e8a IPG |
2444 | */ |
2445 | int usb_new_device(struct usb_device *udev) | |
2446 | { | |
2447 | int err; | |
2448 | ||
16985408 | 2449 | if (udev->parent) { |
16985408 DS |
2450 | /* Initialize non-root-hub device wakeup to disabled; |
2451 | * device (un)configuration controls wakeup capable | |
2452 | * sysfs power/wakeup controls wakeup enabled/disabled | |
2453 | */ | |
2454 | device_init_wakeup(&udev->dev, 0); | |
16985408 DS |
2455 | } |
2456 | ||
9bbdf1e0 AS |
2457 | /* Tell the runtime-PM framework the device is active */ |
2458 | pm_runtime_set_active(&udev->dev); | |
c08512c7 | 2459 | pm_runtime_get_noresume(&udev->dev); |
fcc4a01e | 2460 | pm_runtime_use_autosuspend(&udev->dev); |
9bbdf1e0 AS |
2461 | pm_runtime_enable(&udev->dev); |
2462 | ||
c08512c7 AS |
2463 | /* By default, forbid autosuspend for all devices. It will be |
2464 | * allowed for hubs during binding. | |
2465 | */ | |
2466 | usb_disable_autosuspend(udev); | |
2467 | ||
8d8558d1 | 2468 | err = usb_enumerate_device(udev); /* Read descriptors */ |
d9d16e8a IPG |
2469 | if (err < 0) |
2470 | goto fail; | |
c6515272 SS |
2471 | dev_dbg(&udev->dev, "udev %d, busnum %d, minor = %d\n", |
2472 | udev->devnum, udev->bus->busnum, | |
2473 | (((udev->bus->busnum-1) * 128) + (udev->devnum-1))); | |
9f8b17e6 KS |
2474 | /* export the usbdev device-node for libusb */ |
2475 | udev->dev.devt = MKDEV(USB_DEVICE_MAJOR, | |
2476 | (((udev->bus->busnum-1) * 128) + (udev->devnum-1))); | |
2477 | ||
6cd13201 AS |
2478 | /* Tell the world! */ |
2479 | announce_device(udev); | |
195af2cc | 2480 | |
b04b3156 TT |
2481 | if (udev->serial) |
2482 | add_device_randomness(udev->serial, strlen(udev->serial)); | |
2483 | if (udev->product) | |
2484 | add_device_randomness(udev->product, strlen(udev->product)); | |
2485 | if (udev->manufacturer) | |
2486 | add_device_randomness(udev->manufacturer, | |
2487 | strlen(udev->manufacturer)); | |
2488 | ||
927bc916 | 2489 | device_enable_async_suspend(&udev->dev); |
d35e70d5 | 2490 | |
a4204ff0 | 2491 | /* check whether the hub or firmware marks this port as non-removable */ |
d35e70d5 MG |
2492 | if (udev->parent) |
2493 | set_usb_port_removable(udev); | |
2494 | ||
782da727 | 2495 | /* Register the device. The device driver is responsible |
3b23dd6f AS |
2496 | * for configuring the device and invoking the add-device |
2497 | * notifier chain (used by usbfs and possibly others). | |
782da727 | 2498 | */ |
9f8b17e6 | 2499 | err = device_add(&udev->dev); |
1da177e4 LT |
2500 | if (err) { |
2501 | dev_err(&udev->dev, "can't device_add, error %d\n", err); | |
2502 | goto fail; | |
2503 | } | |
9ad3d6cc | 2504 | |
fde26380 LT |
2505 | /* Create link files between child device and usb port device. */ |
2506 | if (udev->parent) { | |
ad493e5e | 2507 | struct usb_hub *hub = usb_hub_to_struct_hub(udev->parent); |
d5c3834e DW |
2508 | int port1 = udev->portnum; |
2509 | struct usb_port *port_dev = hub->ports[port1 - 1]; | |
fde26380 LT |
2510 | |
2511 | err = sysfs_create_link(&udev->dev.kobj, | |
2512 | &port_dev->dev.kobj, "port"); | |
2513 | if (err) | |
2514 | goto fail; | |
2515 | ||
2516 | err = sysfs_create_link(&port_dev->dev.kobj, | |
2517 | &udev->dev.kobj, "device"); | |
2518 | if (err) { | |
2519 | sysfs_remove_link(&udev->dev.kobj, "port"); | |
2520 | goto fail; | |
2521 | } | |
971fcd49 | 2522 | |
d5c3834e DW |
2523 | if (!test_and_set_bit(port1, hub->child_usage_bits)) |
2524 | pm_runtime_get_sync(&port_dev->dev); | |
fde26380 LT |
2525 | } |
2526 | ||
3b23dd6f | 2527 | (void) usb_create_ep_devs(&udev->dev, &udev->ep0, udev); |
c08512c7 AS |
2528 | usb_mark_last_busy(udev); |
2529 | pm_runtime_put_sync_autosuspend(&udev->dev); | |
c066475e | 2530 | return err; |
1da177e4 LT |
2531 | |
2532 | fail: | |
2533 | usb_set_device_state(udev, USB_STATE_NOTATTACHED); | |
9bbdf1e0 AS |
2534 | pm_runtime_disable(&udev->dev); |
2535 | pm_runtime_set_suspended(&udev->dev); | |
d9d16e8a | 2536 | return err; |
1da177e4 LT |
2537 | } |
2538 | ||
93993a0a IPG |
2539 | |
2540 | /** | |
fd39c86b RD |
2541 | * usb_deauthorize_device - deauthorize a device (usbcore-internal) |
2542 | * @usb_dev: USB device | |
2543 | * | |
2544 | * Move the USB device to a very basic state where interfaces are disabled | |
2545 | * and the device is in fact unconfigured and unusable. | |
93993a0a IPG |
2546 | * |
2547 | * We share a lock (that we have) with device_del(), so we need to | |
2548 | * defer its call. | |
626f090c YB |
2549 | * |
2550 | * Return: 0. | |
93993a0a IPG |
2551 | */ |
2552 | int usb_deauthorize_device(struct usb_device *usb_dev) | |
2553 | { | |
93993a0a IPG |
2554 | usb_lock_device(usb_dev); |
2555 | if (usb_dev->authorized == 0) | |
2556 | goto out_unauthorized; | |
da307123 | 2557 | |
93993a0a IPG |
2558 | usb_dev->authorized = 0; |
2559 | usb_set_configuration(usb_dev, -1); | |
da307123 | 2560 | |
93993a0a IPG |
2561 | out_unauthorized: |
2562 | usb_unlock_device(usb_dev); | |
2563 | return 0; | |
2564 | } | |
2565 | ||
2566 | ||
2567 | int usb_authorize_device(struct usb_device *usb_dev) | |
2568 | { | |
2569 | int result = 0, c; | |
da307123 | 2570 | |
93993a0a IPG |
2571 | usb_lock_device(usb_dev); |
2572 | if (usb_dev->authorized == 1) | |
2573 | goto out_authorized; | |
da307123 | 2574 | |
93993a0a IPG |
2575 | result = usb_autoresume_device(usb_dev); |
2576 | if (result < 0) { | |
2577 | dev_err(&usb_dev->dev, | |
2578 | "can't autoresume for authorization: %d\n", result); | |
2579 | goto error_autoresume; | |
2580 | } | |
e50a322e JG |
2581 | |
2582 | if (usb_dev->wusb) { | |
2583 | result = usb_get_device_descriptor(usb_dev, sizeof(usb_dev->descriptor)); | |
2584 | if (result < 0) { | |
2585 | dev_err(&usb_dev->dev, "can't re-read device descriptor for " | |
2586 | "authorization: %d\n", result); | |
2587 | goto error_device_descriptor; | |
2588 | } | |
93993a0a | 2589 | } |
da307123 | 2590 | |
93993a0a | 2591 | usb_dev->authorized = 1; |
93993a0a IPG |
2592 | /* Choose and set the configuration. This registers the interfaces |
2593 | * with the driver core and lets interface drivers bind to them. | |
2594 | */ | |
b5ea060f | 2595 | c = usb_choose_configuration(usb_dev); |
93993a0a IPG |
2596 | if (c >= 0) { |
2597 | result = usb_set_configuration(usb_dev, c); | |
2598 | if (result) { | |
2599 | dev_err(&usb_dev->dev, | |
2600 | "can't set config #%d, error %d\n", c, result); | |
2601 | /* This need not be fatal. The user can try to | |
2602 | * set other configurations. */ | |
2603 | } | |
2604 | } | |
2605 | dev_info(&usb_dev->dev, "authorized to connect\n"); | |
da307123 | 2606 | |
93993a0a | 2607 | error_device_descriptor: |
da307123 | 2608 | usb_autosuspend_device(usb_dev); |
93993a0a IPG |
2609 | error_autoresume: |
2610 | out_authorized: | |
781b2137 | 2611 | usb_unlock_device(usb_dev); /* complements locktree */ |
93993a0a IPG |
2612 | return result; |
2613 | } | |
2614 | ||
2615 | ||
0165de09 IPG |
2616 | /* Returns 1 if @hub is a WUSB root hub, 0 otherwise */ |
2617 | static unsigned hub_is_wusb(struct usb_hub *hub) | |
2618 | { | |
2619 | struct usb_hcd *hcd; | |
2620 | if (hub->hdev->parent != NULL) /* not a root hub? */ | |
2621 | return 0; | |
2622 | hcd = container_of(hub->hdev->bus, struct usb_hcd, self); | |
2623 | return hcd->wireless; | |
2624 | } | |
2625 | ||
2626 | ||
1da177e4 LT |
2627 | #define PORT_RESET_TRIES 5 |
2628 | #define SET_ADDRESS_TRIES 2 | |
2629 | #define GET_DESCRIPTOR_TRIES 2 | |
2630 | #define SET_CONFIG_TRIES (2 * (use_both_schemes + 1)) | |
90ab5ee9 | 2631 | #define USE_NEW_SCHEME(i) ((i) / 2 == (int)old_scheme_first) |
1da177e4 LT |
2632 | |
2633 | #define HUB_ROOT_RESET_TIME 50 /* times are in msec */ | |
2634 | #define HUB_SHORT_RESET_TIME 10 | |
75d7cf72 | 2635 | #define HUB_BH_RESET_TIME 50 |
1da177e4 | 2636 | #define HUB_LONG_RESET_TIME 200 |
77c7f072 | 2637 | #define HUB_RESET_TIMEOUT 800 |
1da177e4 | 2638 | |
48fc7dbd DW |
2639 | /* |
2640 | * "New scheme" enumeration causes an extra state transition to be | |
2641 | * exposed to an xhci host and causes USB3 devices to receive control | |
2642 | * commands in the default state. This has been seen to cause | |
2643 | * enumeration failures, so disable this enumeration scheme for USB3 | |
2644 | * devices. | |
2645 | */ | |
2646 | static bool use_new_scheme(struct usb_device *udev, int retry) | |
2647 | { | |
2648 | if (udev->speed == USB_SPEED_SUPER) | |
2649 | return false; | |
2650 | ||
2651 | return USE_NEW_SCHEME(retry); | |
2652 | } | |
2653 | ||
025d4430 | 2654 | /* Is a USB 3.0 port in the Inactive or Compliance Mode state? |
8bea2bd3 SL |
2655 | * Port worm reset is required to recover |
2656 | */ | |
3cd12f91 DW |
2657 | static bool hub_port_warm_reset_required(struct usb_hub *hub, int port1, |
2658 | u16 portstatus) | |
10d674a8 | 2659 | { |
3cd12f91 DW |
2660 | u16 link_state; |
2661 | ||
2662 | if (!hub_is_superspeed(hub->hdev)) | |
2663 | return false; | |
2664 | ||
2665 | if (test_bit(port1, hub->warm_reset_bits)) | |
2666 | return true; | |
2667 | ||
2668 | link_state = portstatus & USB_PORT_STAT_LINK_STATE; | |
2669 | return link_state == USB_SS_PORT_LS_SS_INACTIVE | |
2670 | || link_state == USB_SS_PORT_LS_COMP_MOD; | |
10d674a8 SS |
2671 | } |
2672 | ||
1da177e4 | 2673 | static int hub_port_wait_reset(struct usb_hub *hub, int port1, |
75d7cf72 | 2674 | struct usb_device *udev, unsigned int delay, bool warm) |
1da177e4 LT |
2675 | { |
2676 | int delay_time, ret; | |
2677 | u16 portstatus; | |
2678 | u16 portchange; | |
2679 | ||
2680 | for (delay_time = 0; | |
2681 | delay_time < HUB_RESET_TIMEOUT; | |
2682 | delay_time += delay) { | |
2683 | /* wait to give the device a chance to reset */ | |
2684 | msleep(delay); | |
2685 | ||
2686 | /* read and decode port status */ | |
2687 | ret = hub_port_status(hub, port1, &portstatus, &portchange); | |
2688 | if (ret < 0) | |
2689 | return ret; | |
2690 | ||
4f43447e | 2691 | /* The port state is unknown until the reset completes. */ |
470f0be8 SS |
2692 | if (!(portstatus & USB_PORT_STAT_RESET)) |
2693 | break; | |
1da177e4 LT |
2694 | |
2695 | /* switch to the long delay after two short delay failures */ | |
2696 | if (delay_time >= 2 * HUB_SHORT_RESET_TIME) | |
2697 | delay = HUB_LONG_RESET_TIME; | |
2698 | ||
d99f6b41 DW |
2699 | dev_dbg(&hub->ports[port1 - 1]->dev, |
2700 | "not %sreset yet, waiting %dms\n", | |
2701 | warm ? "warm " : "", delay); | |
1da177e4 LT |
2702 | } |
2703 | ||
470f0be8 SS |
2704 | if ((portstatus & USB_PORT_STAT_RESET)) |
2705 | return -EBUSY; | |
2706 | ||
3cd12f91 | 2707 | if (hub_port_warm_reset_required(hub, port1, portstatus)) |
470f0be8 SS |
2708 | return -ENOTCONN; |
2709 | ||
2710 | /* Device went away? */ | |
2711 | if (!(portstatus & USB_PORT_STAT_CONNECTION)) | |
2712 | return -ENOTCONN; | |
2713 | ||
2714 | /* bomb out completely if the connection bounced. A USB 3.0 | |
2715 | * connection may bounce if multiple warm resets were issued, | |
2716 | * but the device may have successfully re-connected. Ignore it. | |
2717 | */ | |
2718 | if (!hub_is_superspeed(hub->hdev) && | |
2719 | (portchange & USB_PORT_STAT_C_CONNECTION)) | |
2720 | return -ENOTCONN; | |
2721 | ||
2722 | if (!(portstatus & USB_PORT_STAT_ENABLE)) | |
2723 | return -EBUSY; | |
2724 | ||
2725 | if (!udev) | |
2726 | return 0; | |
2727 | ||
2728 | if (hub_is_wusb(hub)) | |
2729 | udev->speed = USB_SPEED_WIRELESS; | |
2730 | else if (hub_is_superspeed(hub->hdev)) | |
2731 | udev->speed = USB_SPEED_SUPER; | |
2732 | else if (portstatus & USB_PORT_STAT_HIGH_SPEED) | |
2733 | udev->speed = USB_SPEED_HIGH; | |
2734 | else if (portstatus & USB_PORT_STAT_LOW_SPEED) | |
2735 | udev->speed = USB_SPEED_LOW; | |
2736 | else | |
2737 | udev->speed = USB_SPEED_FULL; | |
2738 | return 0; | |
1da177e4 LT |
2739 | } |
2740 | ||
75d7cf72 | 2741 | /* Handle port reset and port warm(BH) reset (for USB3 protocol ports) */ |
1da177e4 | 2742 | static int hub_port_reset(struct usb_hub *hub, int port1, |
75d7cf72 | 2743 | struct usb_device *udev, unsigned int delay, bool warm) |
1da177e4 LT |
2744 | { |
2745 | int i, status; | |
a24a6078 | 2746 | u16 portchange, portstatus; |
d99f6b41 | 2747 | struct usb_port *port_dev = hub->ports[port1 - 1]; |
1da177e4 | 2748 | |
0fe51aa5 SS |
2749 | if (!hub_is_superspeed(hub->hdev)) { |
2750 | if (warm) { | |
75d7cf72 AX |
2751 | dev_err(hub->intfdev, "only USB3 hub support " |
2752 | "warm reset\n"); | |
2753 | return -EINVAL; | |
2754 | } | |
0fe51aa5 SS |
2755 | /* Block EHCI CF initialization during the port reset. |
2756 | * Some companion controllers don't like it when they mix. | |
2757 | */ | |
2758 | down_read(&ehci_cf_port_reset_rwsem); | |
d3b9d7a9 SS |
2759 | } else if (!warm) { |
2760 | /* | |
2761 | * If the caller hasn't explicitly requested a warm reset, | |
2762 | * double check and see if one is needed. | |
2763 | */ | |
fb6d1f7d RS |
2764 | if (hub_port_status(hub, port1, &portstatus, &portchange) == 0) |
2765 | if (hub_port_warm_reset_required(hub, port1, | |
2766 | portstatus)) | |
2767 | warm = true; | |
75d7cf72 | 2768 | } |
3cd12f91 | 2769 | clear_bit(port1, hub->warm_reset_bits); |
32fe0198 | 2770 | |
1da177e4 LT |
2771 | /* Reset the port */ |
2772 | for (i = 0; i < PORT_RESET_TRIES; i++) { | |
75d7cf72 AX |
2773 | status = set_port_feature(hub->hdev, port1, (warm ? |
2774 | USB_PORT_FEAT_BH_PORT_RESET : | |
2775 | USB_PORT_FEAT_RESET)); | |
e9e88fb7 AS |
2776 | if (status == -ENODEV) { |
2777 | ; /* The hub is gone */ | |
2778 | } else if (status) { | |
d99f6b41 DW |
2779 | dev_err(&port_dev->dev, |
2780 | "cannot %sreset (err = %d)\n", | |
2781 | warm ? "warm " : "", status); | |
75d7cf72 AX |
2782 | } else { |
2783 | status = hub_port_wait_reset(hub, port1, udev, delay, | |
2784 | warm); | |
e9e88fb7 | 2785 | if (status && status != -ENOTCONN && status != -ENODEV) |
1da177e4 LT |
2786 | dev_dbg(hub->intfdev, |
2787 | "port_wait_reset: err = %d\n", | |
2788 | status); | |
2789 | } | |
2790 | ||
a24a6078 | 2791 | /* Check for disconnect or reset */ |
75d7cf72 | 2792 | if (status == 0 || status == -ENOTCONN || status == -ENODEV) { |
fb6d1f7d RS |
2793 | usb_clear_port_feature(hub->hdev, port1, |
2794 | USB_PORT_FEAT_C_RESET); | |
a24a6078 SS |
2795 | |
2796 | if (!hub_is_superspeed(hub->hdev)) | |
2797 | goto done; | |
2798 | ||
fb6d1f7d RS |
2799 | usb_clear_port_feature(hub->hdev, port1, |
2800 | USB_PORT_FEAT_C_BH_PORT_RESET); | |
2801 | usb_clear_port_feature(hub->hdev, port1, | |
2802 | USB_PORT_FEAT_C_PORT_LINK_STATE); | |
2803 | usb_clear_port_feature(hub->hdev, port1, | |
2804 | USB_PORT_FEAT_C_CONNECTION); | |
2805 | ||
a24a6078 SS |
2806 | /* |
2807 | * If a USB 3.0 device migrates from reset to an error | |
2808 | * state, re-issue the warm reset. | |
2809 | */ | |
2810 | if (hub_port_status(hub, port1, | |
2811 | &portstatus, &portchange) < 0) | |
2812 | goto done; | |
2813 | ||
3cd12f91 DW |
2814 | if (!hub_port_warm_reset_required(hub, port1, |
2815 | portstatus)) | |
a24a6078 SS |
2816 | goto done; |
2817 | ||
2818 | /* | |
2819 | * If the port is in SS.Inactive or Compliance Mode, the | |
2820 | * hot or warm reset failed. Try another warm reset. | |
2821 | */ | |
2822 | if (!warm) { | |
d99f6b41 DW |
2823 | dev_dbg(&port_dev->dev, |
2824 | "hot reset failed, warm reset\n"); | |
a24a6078 SS |
2825 | warm = true; |
2826 | } | |
1da177e4 LT |
2827 | } |
2828 | ||
d99f6b41 DW |
2829 | dev_dbg(&port_dev->dev, |
2830 | "not enabled, trying %sreset again...\n", | |
2831 | warm ? "warm " : ""); | |
1da177e4 LT |
2832 | delay = HUB_LONG_RESET_TIME; |
2833 | } | |
2834 | ||
d99f6b41 | 2835 | dev_err(&port_dev->dev, "Cannot enable. Maybe the USB cable is bad?\n"); |
1da177e4 | 2836 | |
75d7cf72 | 2837 | done: |
fb6d1f7d RS |
2838 | if (status == 0) { |
2839 | /* TRSTRCY = 10 ms; plus some extra */ | |
2840 | msleep(10 + 40); | |
2841 | if (udev) { | |
2842 | struct usb_hcd *hcd = bus_to_hcd(udev->bus); | |
2843 | ||
2844 | update_devnum(udev, 0); | |
2845 | /* The xHC may think the device is already reset, | |
2846 | * so ignore the status. | |
2847 | */ | |
2848 | if (hcd->driver->reset_device) | |
2849 | hcd->driver->reset_device(hcd, udev); | |
2850 | ||
2851 | usb_set_device_state(udev, USB_STATE_DEFAULT); | |
2852 | } | |
2853 | } else { | |
2854 | if (udev) | |
2855 | usb_set_device_state(udev, USB_STATE_NOTATTACHED); | |
2856 | } | |
2857 | ||
0fe51aa5 | 2858 | if (!hub_is_superspeed(hub->hdev)) |
75d7cf72 | 2859 | up_read(&ehci_cf_port_reset_rwsem); |
5e467f6e | 2860 | |
75d7cf72 | 2861 | return status; |
5e467f6e AX |
2862 | } |
2863 | ||
0ed9a57e AX |
2864 | /* Check if a port is power on */ |
2865 | static int port_is_power_on(struct usb_hub *hub, unsigned portstatus) | |
2866 | { | |
2867 | int ret = 0; | |
2868 | ||
2869 | if (hub_is_superspeed(hub->hdev)) { | |
2870 | if (portstatus & USB_SS_PORT_STAT_POWER) | |
2871 | ret = 1; | |
2872 | } else { | |
2873 | if (portstatus & USB_PORT_STAT_POWER) | |
2874 | ret = 1; | |
2875 | } | |
2876 | ||
2877 | return ret; | |
2878 | } | |
2879 | ||
5c79a1e3 DW |
2880 | static void usb_lock_port(struct usb_port *port_dev) |
2881 | __acquires(&port_dev->status_lock) | |
2882 | { | |
2883 | mutex_lock(&port_dev->status_lock); | |
2884 | __acquire(&port_dev->status_lock); | |
2885 | } | |
2886 | ||
2887 | static void usb_unlock_port(struct usb_port *port_dev) | |
2888 | __releases(&port_dev->status_lock) | |
2889 | { | |
2890 | mutex_unlock(&port_dev->status_lock); | |
2891 | __release(&port_dev->status_lock); | |
2892 | } | |
2893 | ||
d388dab7 | 2894 | #ifdef CONFIG_PM |
1da177e4 | 2895 | |
0ed9a57e AX |
2896 | /* Check if a port is suspended(USB2.0 port) or in U3 state(USB3.0 port) */ |
2897 | static int port_is_suspended(struct usb_hub *hub, unsigned portstatus) | |
2898 | { | |
2899 | int ret = 0; | |
2900 | ||
2901 | if (hub_is_superspeed(hub->hdev)) { | |
2902 | if ((portstatus & USB_PORT_STAT_LINK_STATE) | |
2903 | == USB_SS_PORT_LS_U3) | |
2904 | ret = 1; | |
2905 | } else { | |
2906 | if (portstatus & USB_PORT_STAT_SUSPEND) | |
2907 | ret = 1; | |
2908 | } | |
2909 | ||
2910 | return ret; | |
2911 | } | |
b01b03f3 AS |
2912 | |
2913 | /* Determine whether the device on a port is ready for a normal resume, | |
2914 | * is ready for a reset-resume, or should be disconnected. | |
2915 | */ | |
2916 | static int check_port_resume_type(struct usb_device *udev, | |
2917 | struct usb_hub *hub, int port1, | |
7fa40910 | 2918 | int status, u16 portchange, u16 portstatus) |
b01b03f3 | 2919 | { |
d99f6b41 | 2920 | struct usb_port *port_dev = hub->ports[port1 - 1]; |
7fa40910 | 2921 | int retries = 3; |
d99f6b41 | 2922 | |
7fa40910 | 2923 | retry: |
3cd12f91 DW |
2924 | /* Is a warm reset needed to recover the connection? */ |
2925 | if (status == 0 && udev->reset_resume | |
2926 | && hub_port_warm_reset_required(hub, port1, portstatus)) { | |
2927 | /* pass */; | |
2928 | } | |
b01b03f3 | 2929 | /* Is the device still present? */ |
3cd12f91 | 2930 | else if (status || port_is_suspended(hub, portstatus) || |
7fa40910 | 2931 | !port_is_power_on(hub, portstatus)) { |
b01b03f3 AS |
2932 | if (status >= 0) |
2933 | status = -ENODEV; | |
7fa40910 JW |
2934 | } else if (!(portstatus & USB_PORT_STAT_CONNECTION)) { |
2935 | if (retries--) { | |
2936 | usleep_range(200, 300); | |
2937 | status = hub_port_status(hub, port1, &portstatus, | |
2938 | &portchange); | |
2939 | goto retry; | |
2940 | } | |
2941 | status = -ENODEV; | |
b01b03f3 AS |
2942 | } |
2943 | ||
86c57edf AS |
2944 | /* Can't do a normal resume if the port isn't enabled, |
2945 | * so try a reset-resume instead. | |
2946 | */ | |
2947 | else if (!(portstatus & USB_PORT_STAT_ENABLE) && !udev->reset_resume) { | |
2948 | if (udev->persist_enabled) | |
2949 | udev->reset_resume = 1; | |
2950 | else | |
2951 | status = -ENODEV; | |
2952 | } | |
b01b03f3 AS |
2953 | |
2954 | if (status) { | |
d99f6b41 DW |
2955 | dev_dbg(&port_dev->dev, "status %04x.%04x after resume, %d\n", |
2956 | portchange, portstatus, status); | |
b01b03f3 AS |
2957 | } else if (udev->reset_resume) { |
2958 | ||
2959 | /* Late port handoff can set status-change bits */ | |
2960 | if (portchange & USB_PORT_STAT_C_CONNECTION) | |
ad493e5e | 2961 | usb_clear_port_feature(hub->hdev, port1, |
b01b03f3 AS |
2962 | USB_PORT_FEAT_C_CONNECTION); |
2963 | if (portchange & USB_PORT_STAT_C_ENABLE) | |
ad493e5e | 2964 | usb_clear_port_feature(hub->hdev, port1, |
b01b03f3 AS |
2965 | USB_PORT_FEAT_C_ENABLE); |
2966 | } | |
2967 | ||
2968 | return status; | |
2969 | } | |
2970 | ||
f74631e3 SS |
2971 | int usb_disable_ltm(struct usb_device *udev) |
2972 | { | |
2973 | struct usb_hcd *hcd = bus_to_hcd(udev->bus); | |
2974 | ||
2975 | /* Check if the roothub and device supports LTM. */ | |
2976 | if (!usb_device_supports_ltm(hcd->self.root_hub) || | |
2977 | !usb_device_supports_ltm(udev)) | |
2978 | return 0; | |
2979 | ||
2980 | /* Clear Feature LTM Enable can only be sent if the device is | |
2981 | * configured. | |
2982 | */ | |
2983 | if (!udev->actconfig) | |
2984 | return 0; | |
2985 | ||
2986 | return usb_control_msg(udev, usb_sndctrlpipe(udev, 0), | |
2987 | USB_REQ_CLEAR_FEATURE, USB_RECIP_DEVICE, | |
2988 | USB_DEVICE_LTM_ENABLE, 0, NULL, 0, | |
2989 | USB_CTRL_SET_TIMEOUT); | |
2990 | } | |
2991 | EXPORT_SYMBOL_GPL(usb_disable_ltm); | |
2992 | ||
2993 | void usb_enable_ltm(struct usb_device *udev) | |
2994 | { | |
2995 | struct usb_hcd *hcd = bus_to_hcd(udev->bus); | |
2996 | ||
2997 | /* Check if the roothub and device supports LTM. */ | |
2998 | if (!usb_device_supports_ltm(hcd->self.root_hub) || | |
2999 | !usb_device_supports_ltm(udev)) | |
3000 | return; | |
3001 | ||
3002 | /* Set Feature LTM Enable can only be sent if the device is | |
3003 | * configured. | |
3004 | */ | |
3005 | if (!udev->actconfig) | |
3006 | return; | |
3007 | ||
3008 | usb_control_msg(udev, usb_sndctrlpipe(udev, 0), | |
3009 | USB_REQ_SET_FEATURE, USB_RECIP_DEVICE, | |
3010 | USB_DEVICE_LTM_ENABLE, 0, NULL, 0, | |
3011 | USB_CTRL_SET_TIMEOUT); | |
3012 | } | |
3013 | EXPORT_SYMBOL_GPL(usb_enable_ltm); | |
3014 | ||
54a3ac0c | 3015 | /* |
28e86165 | 3016 | * usb_enable_remote_wakeup - enable remote wakeup for a device |
54a3ac0c LT |
3017 | * @udev: target device |
3018 | * | |
28e86165 AS |
3019 | * For USB-2 devices: Set the device's remote wakeup feature. |
3020 | * | |
3021 | * For USB-3 devices: Assume there's only one function on the device and | |
3022 | * enable remote wake for the first interface. FIXME if the interface | |
3023 | * association descriptor shows there's more than one function. | |
54a3ac0c | 3024 | */ |
28e86165 | 3025 | static int usb_enable_remote_wakeup(struct usb_device *udev) |
54a3ac0c | 3026 | { |
28e86165 AS |
3027 | if (udev->speed < USB_SPEED_SUPER) |
3028 | return usb_control_msg(udev, usb_sndctrlpipe(udev, 0), | |
3029 | USB_REQ_SET_FEATURE, USB_RECIP_DEVICE, | |
3030 | USB_DEVICE_REMOTE_WAKEUP, 0, NULL, 0, | |
3031 | USB_CTRL_SET_TIMEOUT); | |
3032 | else | |
3033 | return usb_control_msg(udev, usb_sndctrlpipe(udev, 0), | |
3034 | USB_REQ_SET_FEATURE, USB_RECIP_INTERFACE, | |
3035 | USB_INTRF_FUNC_SUSPEND, | |
3036 | USB_INTRF_FUNC_SUSPEND_RW | | |
3037 | USB_INTRF_FUNC_SUSPEND_LP, | |
3038 | NULL, 0, USB_CTRL_SET_TIMEOUT); | |
3039 | } | |
3040 | ||
3041 | /* | |
3042 | * usb_disable_remote_wakeup - disable remote wakeup for a device | |
3043 | * @udev: target device | |
3044 | * | |
3045 | * For USB-2 devices: Clear the device's remote wakeup feature. | |
3046 | * | |
3047 | * For USB-3 devices: Assume there's only one function on the device and | |
3048 | * disable remote wake for the first interface. FIXME if the interface | |
3049 | * association descriptor shows there's more than one function. | |
3050 | */ | |
3051 | static int usb_disable_remote_wakeup(struct usb_device *udev) | |
3052 | { | |
3053 | if (udev->speed < USB_SPEED_SUPER) | |
3054 | return usb_control_msg(udev, usb_sndctrlpipe(udev, 0), | |
3055 | USB_REQ_CLEAR_FEATURE, USB_RECIP_DEVICE, | |
3056 | USB_DEVICE_REMOTE_WAKEUP, 0, NULL, 0, | |
3057 | USB_CTRL_SET_TIMEOUT); | |
3058 | else | |
3059 | return usb_control_msg(udev, usb_sndctrlpipe(udev, 0), | |
54a3ac0c LT |
3060 | USB_REQ_CLEAR_FEATURE, USB_RECIP_INTERFACE, |
3061 | USB_INTRF_FUNC_SUSPEND, 0, NULL, 0, | |
3062 | USB_CTRL_SET_TIMEOUT); | |
3063 | } | |
1da177e4 | 3064 | |
e583d9db AS |
3065 | /* Count of wakeup-enabled devices at or below udev */ |
3066 | static unsigned wakeup_enabled_descendants(struct usb_device *udev) | |
3067 | { | |
3068 | struct usb_hub *hub = usb_hub_to_struct_hub(udev); | |
3069 | ||
3070 | return udev->do_remote_wakeup + | |
3071 | (hub ? hub->wakeup_enabled_descendants : 0); | |
3072 | } | |
3073 | ||
1da177e4 | 3074 | /* |
624d6c07 AS |
3075 | * usb_port_suspend - suspend a usb device's upstream port |
3076 | * @udev: device that's no longer in active use, not a root hub | |
3077 | * Context: must be able to sleep; device not locked; pm locks held | |
3078 | * | |
3079 | * Suspends a USB device that isn't in active use, conserving power. | |
3080 | * Devices may wake out of a suspend, if anything important happens, | |
3081 | * using the remote wakeup mechanism. They may also be taken out of | |
3082 | * suspend by the host, using usb_port_resume(). It's also routine | |
3083 | * to disconnect devices while they are suspended. | |
3084 | * | |
3085 | * This only affects the USB hardware for a device; its interfaces | |
3086 | * (and, for hubs, child devices) must already have been suspended. | |
3087 | * | |
1da177e4 LT |
3088 | * Selective port suspend reduces power; most suspended devices draw |
3089 | * less than 500 uA. It's also used in OTG, along with remote wakeup. | |
3090 | * All devices below the suspended port are also suspended. | |
3091 | * | |
3092 | * Devices leave suspend state when the host wakes them up. Some devices | |
3093 | * also support "remote wakeup", where the device can activate the USB | |
3094 | * tree above them to deliver data, such as a keypress or packet. In | |
3095 | * some cases, this wakes the USB host. | |
624d6c07 AS |
3096 | * |
3097 | * Suspending OTG devices may trigger HNP, if that's been enabled | |
3098 | * between a pair of dual-role devices. That will change roles, such | |
3099 | * as from A-Host to A-Peripheral or from B-Host back to B-Peripheral. | |
3100 | * | |
3101 | * Devices on USB hub ports have only one "suspend" state, corresponding | |
3102 | * to ACPI D2, "may cause the device to lose some context". | |
3103 | * State transitions include: | |
3104 | * | |
3105 | * - suspend, resume ... when the VBUS power link stays live | |
3106 | * - suspend, disconnect ... VBUS lost | |
3107 | * | |
3108 | * Once VBUS drop breaks the circuit, the port it's using has to go through | |
3109 | * normal re-enumeration procedures, starting with enabling VBUS power. | |
3110 | * Other than re-initializing the hub (plug/unplug, except for root hubs), | |
37ebb549 | 3111 | * Linux (2.6) currently has NO mechanisms to initiate that: no hub_wq |
624d6c07 AS |
3112 | * timer, no SRP, no requests through sysfs. |
3113 | * | |
e583d9db AS |
3114 | * If Runtime PM isn't enabled or used, non-SuperSpeed devices may not get |
3115 | * suspended until their bus goes into global suspend (i.e., the root | |
0aa2832d AS |
3116 | * hub is suspended). Nevertheless, we change @udev->state to |
3117 | * USB_STATE_SUSPENDED as this is the device's "logical" state. The actual | |
3118 | * upstream port setting is stored in @udev->port_is_suspended. | |
624d6c07 AS |
3119 | * |
3120 | * Returns 0 on success, else negative errno. | |
1da177e4 | 3121 | */ |
65bfd296 | 3122 | int usb_port_suspend(struct usb_device *udev, pm_message_t msg) |
1da177e4 | 3123 | { |
ad493e5e LT |
3124 | struct usb_hub *hub = usb_hub_to_struct_hub(udev->parent); |
3125 | struct usb_port *port_dev = hub->ports[udev->portnum - 1]; | |
624d6c07 AS |
3126 | int port1 = udev->portnum; |
3127 | int status; | |
0aa2832d | 3128 | bool really_suspend = true; |
1da177e4 | 3129 | |
5c79a1e3 DW |
3130 | usb_lock_port(port_dev); |
3131 | ||
1da177e4 LT |
3132 | /* enable remote wakeup when appropriate; this lets the device |
3133 | * wake up the upstream hub (including maybe the root hub). | |
3134 | * | |
3135 | * NOTE: OTG devices may issue remote wakeup (or SRP) even when | |
3136 | * we don't explicitly enable it here. | |
3137 | */ | |
645daaab | 3138 | if (udev->do_remote_wakeup) { |
28e86165 | 3139 | status = usb_enable_remote_wakeup(udev); |
0c487206 | 3140 | if (status) { |
624d6c07 AS |
3141 | dev_dbg(&udev->dev, "won't remote wakeup, status %d\n", |
3142 | status); | |
0c487206 | 3143 | /* bail if autosuspend is requested */ |
5b1b0b81 | 3144 | if (PMSG_IS_AUTO(msg)) |
4fae6f0f | 3145 | goto err_wakeup; |
0c487206 | 3146 | } |
1da177e4 LT |
3147 | } |
3148 | ||
65580b43 AX |
3149 | /* disable USB2 hardware LPM */ |
3150 | if (udev->usb2_hw_lpm_enabled == 1) | |
3151 | usb_set_usb2_hardware_lpm(udev, 0); | |
3152 | ||
f74631e3 | 3153 | if (usb_disable_ltm(udev)) { |
4fae6f0f AS |
3154 | dev_err(&udev->dev, "Failed to disable LTM before suspend\n."); |
3155 | status = -ENOMEM; | |
3156 | if (PMSG_IS_AUTO(msg)) | |
3157 | goto err_ltm; | |
f74631e3 | 3158 | } |
8306095f | 3159 | if (usb_unlocked_disable_lpm(udev)) { |
4fae6f0f AS |
3160 | dev_err(&udev->dev, "Failed to disable LPM before suspend\n."); |
3161 | status = -ENOMEM; | |
3162 | if (PMSG_IS_AUTO(msg)) | |
3163 | goto err_lpm3; | |
8306095f SS |
3164 | } |
3165 | ||
1da177e4 | 3166 | /* see 7.1.7.6 */ |
a7114230 | 3167 | if (hub_is_superspeed(hub->hdev)) |
c2f60db7 | 3168 | status = hub_set_port_link_state(hub, port1, USB_SS_PORT_LS_U3); |
e583d9db | 3169 | |
0aa2832d AS |
3170 | /* |
3171 | * For system suspend, we do not need to enable the suspend feature | |
3172 | * on individual USB-2 ports. The devices will automatically go | |
3173 | * into suspend a few ms after the root hub stops sending packets. | |
3174 | * The USB 2.0 spec calls this "global suspend". | |
e583d9db AS |
3175 | * |
3176 | * However, many USB hubs have a bug: They don't relay wakeup requests | |
3177 | * from a downstream port if the port's suspend feature isn't on. | |
3178 | * Therefore we will turn on the suspend feature if udev or any of its | |
3179 | * descendants is enabled for remote wakeup. | |
0aa2832d | 3180 | */ |
e583d9db AS |
3181 | else if (PMSG_IS_AUTO(msg) || wakeup_enabled_descendants(udev) > 0) |
3182 | status = set_port_feature(hub->hdev, port1, | |
3183 | USB_PORT_FEAT_SUSPEND); | |
0aa2832d AS |
3184 | else { |
3185 | really_suspend = false; | |
3186 | status = 0; | |
3187 | } | |
1da177e4 | 3188 | if (status) { |
d99f6b41 | 3189 | dev_dbg(&port_dev->dev, "can't suspend, status %d\n", status); |
cbb33004 | 3190 | |
4fae6f0f AS |
3191 | /* Try to enable USB3 LPM and LTM again */ |
3192 | usb_unlocked_enable_lpm(udev); | |
3193 | err_lpm3: | |
3194 | usb_enable_ltm(udev); | |
3195 | err_ltm: | |
c3e751e4 AX |
3196 | /* Try to enable USB2 hardware LPM again */ |
3197 | if (udev->usb2_hw_lpm_capable == 1) | |
3198 | usb_set_usb2_hardware_lpm(udev, 1); | |
3199 | ||
4fae6f0f AS |
3200 | if (udev->do_remote_wakeup) |
3201 | (void) usb_disable_remote_wakeup(udev); | |
3202 | err_wakeup: | |
8306095f | 3203 | |
cbb33004 | 3204 | /* System sleep transitions should never fail */ |
5b1b0b81 | 3205 | if (!PMSG_IS_AUTO(msg)) |
cbb33004 | 3206 | status = 0; |
1da177e4 | 3207 | } else { |
30b1a7a3 AS |
3208 | dev_dbg(&udev->dev, "usb %ssuspend, wakeup %d\n", |
3209 | (PMSG_IS_AUTO(msg) ? "auto-" : ""), | |
3210 | udev->do_remote_wakeup); | |
0aa2832d AS |
3211 | if (really_suspend) { |
3212 | udev->port_is_suspended = 1; | |
e583d9db AS |
3213 | |
3214 | /* device has up to 10 msec to fully suspend */ | |
0aa2832d AS |
3215 | msleep(10); |
3216 | } | |
e583d9db | 3217 | usb_set_device_state(udev, USB_STATE_SUSPENDED); |
1da177e4 | 3218 | } |
ad493e5e | 3219 | |
d5c3834e DW |
3220 | if (status == 0 && !udev->do_remote_wakeup && udev->persist_enabled |
3221 | && test_and_clear_bit(port1, hub->child_usage_bits)) | |
98a4f1ff | 3222 | pm_runtime_put_sync(&port_dev->dev); |
ad493e5e | 3223 | |
c08512c7 | 3224 | usb_mark_last_busy(hub->hdev); |
5c79a1e3 DW |
3225 | |
3226 | usb_unlock_port(port_dev); | |
1da177e4 LT |
3227 | return status; |
3228 | } | |
3229 | ||
1da177e4 | 3230 | /* |
390a8c34 DB |
3231 | * If the USB "suspend" state is in use (rather than "global suspend"), |
3232 | * many devices will be individually taken out of suspend state using | |
54515fe5 | 3233 | * special "resume" signaling. This routine kicks in shortly after |
1da177e4 LT |
3234 | * hardware resume signaling is finished, either because of selective |
3235 | * resume (by host) or remote wakeup (by device) ... now see what changed | |
3236 | * in the tree that's rooted at this device. | |
54515fe5 AS |
3237 | * |
3238 | * If @udev->reset_resume is set then the device is reset before the | |
3239 | * status check is done. | |
1da177e4 | 3240 | */ |
140d8f68 | 3241 | static int finish_port_resume(struct usb_device *udev) |
1da177e4 | 3242 | { |
54515fe5 | 3243 | int status = 0; |
07e72b95 | 3244 | u16 devstatus = 0; |
1da177e4 LT |
3245 | |
3246 | /* caller owns the udev device lock */ | |
b9cef6c3 WF |
3247 | dev_dbg(&udev->dev, "%s\n", |
3248 | udev->reset_resume ? "finish reset-resume" : "finish resume"); | |
1da177e4 LT |
3249 | |
3250 | /* usb ch9 identifies four variants of SUSPENDED, based on what | |
3251 | * state the device resumes to. Linux currently won't see the | |
3252 | * first two on the host side; they'd be inside hub_port_init() | |
37ebb549 | 3253 | * during many timeouts, but hub_wq can't suspend until later. |
1da177e4 LT |
3254 | */ |
3255 | usb_set_device_state(udev, udev->actconfig | |
3256 | ? USB_STATE_CONFIGURED | |
3257 | : USB_STATE_ADDRESS); | |
1da177e4 | 3258 | |
54515fe5 AS |
3259 | /* 10.5.4.5 says not to reset a suspended port if the attached |
3260 | * device is enabled for remote wakeup. Hence the reset | |
3261 | * operation is carried out here, after the port has been | |
3262 | * resumed. | |
3263 | */ | |
1d10255c AS |
3264 | if (udev->reset_resume) { |
3265 | /* | |
3266 | * If the device morphs or switches modes when it is reset, | |
3267 | * we don't want to perform a reset-resume. We'll fail the | |
3268 | * resume, which will cause a logical disconnect, and then | |
3269 | * the device will be rediscovered. | |
3270 | */ | |
86c57edf | 3271 | retry_reset_resume: |
1d10255c AS |
3272 | if (udev->quirks & USB_QUIRK_RESET) |
3273 | status = -ENODEV; | |
3274 | else | |
3275 | status = usb_reset_and_verify_device(udev); | |
3276 | } | |
54515fe5 | 3277 | |
469271f8 MB |
3278 | /* 10.5.4.5 says be sure devices in the tree are still there. |
3279 | * For now let's assume the device didn't go crazy on resume, | |
1da177e4 LT |
3280 | * and device drivers will know about any resume quirks. |
3281 | */ | |
54515fe5 | 3282 | if (status == 0) { |
46dede46 | 3283 | devstatus = 0; |
54515fe5 | 3284 | status = usb_get_status(udev, USB_RECIP_DEVICE, 0, &devstatus); |
86c57edf AS |
3285 | |
3286 | /* If a normal resume failed, try doing a reset-resume */ | |
3287 | if (status && !udev->reset_resume && udev->persist_enabled) { | |
3288 | dev_dbg(&udev->dev, "retry with reset-resume\n"); | |
3289 | udev->reset_resume = 1; | |
3290 | goto retry_reset_resume; | |
3291 | } | |
54515fe5 | 3292 | } |
b40b7a90 | 3293 | |
624d6c07 AS |
3294 | if (status) { |
3295 | dev_dbg(&udev->dev, "gone after usb resume? status %d\n", | |
3296 | status); | |
07e72b95 ON |
3297 | /* |
3298 | * There are a few quirky devices which violate the standard | |
3299 | * by claiming to have remote wakeup enabled after a reset, | |
3300 | * which crash if the feature is cleared, hence check for | |
3301 | * udev->reset_resume | |
3302 | */ | |
3303 | } else if (udev->actconfig && !udev->reset_resume) { | |
28e86165 | 3304 | if (udev->speed < USB_SPEED_SUPER) { |
54a3ac0c | 3305 | if (devstatus & (1 << USB_DEVICE_REMOTE_WAKEUP)) |
28e86165 | 3306 | status = usb_disable_remote_wakeup(udev); |
54a3ac0c LT |
3307 | } else { |
3308 | status = usb_get_status(udev, USB_RECIP_INTERFACE, 0, | |
3309 | &devstatus); | |
54a3ac0c LT |
3310 | if (!status && devstatus & (USB_INTRF_STAT_FUNC_RW_CAP |
3311 | | USB_INTRF_STAT_FUNC_RW)) | |
28e86165 | 3312 | status = usb_disable_remote_wakeup(udev); |
4bf0ba86 | 3313 | } |
54a3ac0c LT |
3314 | |
3315 | if (status) | |
3316 | dev_dbg(&udev->dev, | |
3317 | "disable remote wakeup, status %d\n", | |
3318 | status); | |
1da177e4 | 3319 | status = 0; |
1da177e4 LT |
3320 | } |
3321 | return status; | |
3322 | } | |
3323 | ||
a40178b2 PA |
3324 | /* |
3325 | * There are some SS USB devices which take longer time for link training. | |
3326 | * XHCI specs 4.19.4 says that when Link training is successful, port | |
3327 | * sets CSC bit to 1. So if SW reads port status before successful link | |
3328 | * training, then it will not find device to be present. | |
3329 | * USB Analyzer log with such buggy devices show that in some cases | |
3330 | * device switch on the RX termination after long delay of host enabling | |
3331 | * the VBUS. In few other cases it has been seen that device fails to | |
3332 | * negotiate link training in first attempt. It has been | |
3333 | * reported till now that few devices take as long as 2000 ms to train | |
3334 | * the link after host enabling its VBUS and termination. Following | |
3335 | * routine implements a 2000 ms timeout for link training. If in a case | |
3336 | * link trains before timeout, loop will exit earlier. | |
3337 | * | |
3338 | * FIXME: If a device was connected before suspend, but was removed | |
3339 | * while system was asleep, then the loop in the following routine will | |
3340 | * only exit at timeout. | |
3341 | * | |
3342 | * This routine should only be called when persist is enabled for a SS | |
3343 | * device. | |
3344 | */ | |
3345 | static int wait_for_ss_port_enable(struct usb_device *udev, | |
3346 | struct usb_hub *hub, int *port1, | |
3347 | u16 *portchange, u16 *portstatus) | |
3348 | { | |
3349 | int status = 0, delay_ms = 0; | |
3350 | ||
3351 | while (delay_ms < 2000) { | |
3352 | if (status || *portstatus & USB_PORT_STAT_CONNECTION) | |
3353 | break; | |
3354 | msleep(20); | |
3355 | delay_ms += 20; | |
3356 | status = hub_port_status(hub, *port1, portstatus, portchange); | |
3357 | } | |
3358 | return status; | |
3359 | } | |
3360 | ||
624d6c07 AS |
3361 | /* |
3362 | * usb_port_resume - re-activate a suspended usb device's upstream port | |
3363 | * @udev: device to re-activate, not a root hub | |
3364 | * Context: must be able to sleep; device not locked; pm locks held | |
3365 | * | |
3366 | * This will re-activate the suspended device, increasing power usage | |
3367 | * while letting drivers communicate again with its endpoints. | |
3368 | * USB resume explicitly guarantees that the power session between | |
3369 | * the host and the device is the same as it was when the device | |
3370 | * suspended. | |
3371 | * | |
feccc30d AS |
3372 | * If @udev->reset_resume is set then this routine won't check that the |
3373 | * port is still enabled. Furthermore, finish_port_resume() above will | |
54515fe5 AS |
3374 | * reset @udev. The end result is that a broken power session can be |
3375 | * recovered and @udev will appear to persist across a loss of VBUS power. | |
3376 | * | |
3377 | * For example, if a host controller doesn't maintain VBUS suspend current | |
3378 | * during a system sleep or is reset when the system wakes up, all the USB | |
3379 | * power sessions below it will be broken. This is especially troublesome | |
3380 | * for mass-storage devices containing mounted filesystems, since the | |
3381 | * device will appear to have disconnected and all the memory mappings | |
3382 | * to it will be lost. Using the USB_PERSIST facility, the device can be | |
3383 | * made to appear as if it had not disconnected. | |
3384 | * | |
742120c6 | 3385 | * This facility can be dangerous. Although usb_reset_and_verify_device() makes |
feccc30d | 3386 | * every effort to insure that the same device is present after the |
54515fe5 AS |
3387 | * reset as before, it cannot provide a 100% guarantee. Furthermore it's |
3388 | * quite possible for a device to remain unaltered but its media to be | |
3389 | * changed. If the user replaces a flash memory card while the system is | |
3390 | * asleep, he will have only himself to blame when the filesystem on the | |
3391 | * new card is corrupted and the system crashes. | |
3392 | * | |
624d6c07 AS |
3393 | * Returns 0 on success, else negative errno. |
3394 | */ | |
65bfd296 | 3395 | int usb_port_resume(struct usb_device *udev, pm_message_t msg) |
1da177e4 | 3396 | { |
ad493e5e LT |
3397 | struct usb_hub *hub = usb_hub_to_struct_hub(udev->parent); |
3398 | struct usb_port *port_dev = hub->ports[udev->portnum - 1]; | |
624d6c07 AS |
3399 | int port1 = udev->portnum; |
3400 | int status; | |
3401 | u16 portchange, portstatus; | |
d25450c6 | 3402 | |
d5c3834e | 3403 | if (!test_and_set_bit(port1, hub->child_usage_bits)) { |
ad493e5e | 3404 | status = pm_runtime_get_sync(&port_dev->dev); |
ad493e5e LT |
3405 | if (status < 0) { |
3406 | dev_dbg(&udev->dev, "can't resume usb port, status %d\n", | |
3407 | status); | |
3408 | return status; | |
3409 | } | |
3410 | } | |
3411 | ||
5c79a1e3 DW |
3412 | usb_lock_port(port_dev); |
3413 | ||
d25450c6 AS |
3414 | /* Skip the initial Clear-Suspend step for a remote wakeup */ |
3415 | status = hub_port_status(hub, port1, &portstatus, &portchange); | |
0ed9a57e | 3416 | if (status == 0 && !port_is_suspended(hub, portstatus)) |
d25450c6 | 3417 | goto SuspendCleared; |
1da177e4 | 3418 | |
1da177e4 | 3419 | /* see 7.1.7.7; affects power usage, but not budgeting */ |
a7114230 | 3420 | if (hub_is_superspeed(hub->hdev)) |
c2f60db7 | 3421 | status = hub_set_port_link_state(hub, port1, USB_SS_PORT_LS_U0); |
a7114230 | 3422 | else |
ad493e5e | 3423 | status = usb_clear_port_feature(hub->hdev, |
a7114230 | 3424 | port1, USB_PORT_FEAT_SUSPEND); |
1da177e4 | 3425 | if (status) { |
d99f6b41 | 3426 | dev_dbg(&port_dev->dev, "can't resume, status %d\n", status); |
1da177e4 | 3427 | } else { |
bbc78c07 | 3428 | /* drive resume for USB_RESUME_TIMEOUT msec */ |
686314cf | 3429 | dev_dbg(&udev->dev, "usb %sresume\n", |
5b1b0b81 | 3430 | (PMSG_IS_AUTO(msg) ? "auto-" : "")); |
bbc78c07 | 3431 | msleep(USB_RESUME_TIMEOUT); |
1da177e4 | 3432 | |
1da177e4 LT |
3433 | /* Virtual root hubs can trigger on GET_PORT_STATUS to |
3434 | * stop resume signaling. Then finish the resume | |
3435 | * sequence. | |
3436 | */ | |
d25450c6 | 3437 | status = hub_port_status(hub, port1, &portstatus, &portchange); |
54515fe5 | 3438 | |
b01b03f3 AS |
3439 | /* TRSMRCY = 10 msec */ |
3440 | msleep(10); | |
3441 | } | |
3442 | ||
54515fe5 | 3443 | SuspendCleared: |
b01b03f3 | 3444 | if (status == 0) { |
bfd1e910 | 3445 | udev->port_is_suspended = 0; |
a7114230 AX |
3446 | if (hub_is_superspeed(hub->hdev)) { |
3447 | if (portchange & USB_PORT_STAT_C_LINK_STATE) | |
ad493e5e | 3448 | usb_clear_port_feature(hub->hdev, port1, |
a7114230 AX |
3449 | USB_PORT_FEAT_C_PORT_LINK_STATE); |
3450 | } else { | |
3451 | if (portchange & USB_PORT_STAT_C_SUSPEND) | |
ad493e5e | 3452 | usb_clear_port_feature(hub->hdev, port1, |
a7114230 AX |
3453 | USB_PORT_FEAT_C_SUSPEND); |
3454 | } | |
1da177e4 | 3455 | } |
1da177e4 | 3456 | |
a40178b2 PA |
3457 | if (udev->persist_enabled && hub_is_superspeed(hub->hdev)) |
3458 | status = wait_for_ss_port_enable(udev, hub, &port1, &portchange, | |
3459 | &portstatus); | |
3460 | ||
b01b03f3 AS |
3461 | status = check_port_resume_type(udev, |
3462 | hub, port1, status, portchange, portstatus); | |
54515fe5 AS |
3463 | if (status == 0) |
3464 | status = finish_port_resume(udev); | |
3465 | if (status < 0) { | |
3466 | dev_dbg(&udev->dev, "can't resume, status %d\n", status); | |
3467 | hub_port_logical_disconnect(hub, port1); | |
65580b43 AX |
3468 | } else { |
3469 | /* Try to enable USB2 hardware LPM */ | |
3470 | if (udev->usb2_hw_lpm_capable == 1) | |
3471 | usb_set_usb2_hardware_lpm(udev, 1); | |
8306095f | 3472 | |
f74631e3 SS |
3473 | /* Try to enable USB3 LTM and LPM */ |
3474 | usb_enable_ltm(udev); | |
8306095f | 3475 | usb_unlocked_enable_lpm(udev); |
54515fe5 | 3476 | } |
65580b43 | 3477 | |
5c79a1e3 DW |
3478 | usb_unlock_port(port_dev); |
3479 | ||
1da177e4 LT |
3480 | return status; |
3481 | } | |
3482 | ||
0534d468 | 3483 | int usb_remote_wakeup(struct usb_device *udev) |
1da177e4 LT |
3484 | { |
3485 | int status = 0; | |
3486 | ||
5c79a1e3 | 3487 | usb_lock_device(udev); |
1da177e4 | 3488 | if (udev->state == USB_STATE_SUSPENDED) { |
645daaab | 3489 | dev_dbg(&udev->dev, "usb %sresume\n", "wakeup-"); |
9bbdf1e0 AS |
3490 | status = usb_autoresume_device(udev); |
3491 | if (status == 0) { | |
3492 | /* Let the drivers do their thing, then... */ | |
3493 | usb_autosuspend_device(udev); | |
3494 | } | |
1da177e4 | 3495 | } |
5c79a1e3 | 3496 | usb_unlock_device(udev); |
1da177e4 LT |
3497 | return status; |
3498 | } | |
3499 | ||
7e73be22 DW |
3500 | /* Returns 1 if there was a remote wakeup and a connect status change. */ |
3501 | static int hub_handle_remote_wakeup(struct usb_hub *hub, unsigned int port, | |
3502 | u16 portstatus, u16 portchange) | |
3503 | __must_hold(&port_dev->status_lock) | |
3504 | { | |
3505 | struct usb_port *port_dev = hub->ports[port - 1]; | |
3506 | struct usb_device *hdev; | |
3507 | struct usb_device *udev; | |
3508 | int connect_change = 0; | |
3509 | int ret; | |
3510 | ||
3511 | hdev = hub->hdev; | |
3512 | udev = port_dev->child; | |
3513 | if (!hub_is_superspeed(hdev)) { | |
3514 | if (!(portchange & USB_PORT_STAT_C_SUSPEND)) | |
3515 | return 0; | |
3516 | usb_clear_port_feature(hdev, port, USB_PORT_FEAT_C_SUSPEND); | |
3517 | } else { | |
3518 | if (!udev || udev->state != USB_STATE_SUSPENDED || | |
3519 | (portstatus & USB_PORT_STAT_LINK_STATE) != | |
3520 | USB_SS_PORT_LS_U0) | |
3521 | return 0; | |
3522 | } | |
3523 | ||
3524 | if (udev) { | |
3525 | /* TRSMRCY = 10 msec */ | |
3526 | msleep(10); | |
3527 | ||
3528 | usb_unlock_port(port_dev); | |
3529 | ret = usb_remote_wakeup(udev); | |
3530 | usb_lock_port(port_dev); | |
3531 | if (ret < 0) | |
3532 | connect_change = 1; | |
3533 | } else { | |
3534 | ret = -ENODEV; | |
3535 | hub_port_disable(hub, port, 1); | |
3536 | } | |
3537 | dev_dbg(&port_dev->dev, "resume, status %d\n", ret); | |
3538 | return connect_change; | |
3539 | } | |
3540 | ||
e6f30dea ML |
3541 | static int check_ports_changed(struct usb_hub *hub) |
3542 | { | |
3543 | int port1; | |
3544 | ||
3545 | for (port1 = 1; port1 <= hub->hdev->maxchild; ++port1) { | |
3546 | u16 portstatus, portchange; | |
3547 | int status; | |
3548 | ||
3549 | status = hub_port_status(hub, port1, &portstatus, &portchange); | |
3550 | if (!status && portchange) | |
3551 | return 1; | |
3552 | } | |
3553 | return 0; | |
3554 | } | |
3555 | ||
db690874 | 3556 | static int hub_suspend(struct usb_interface *intf, pm_message_t msg) |
1da177e4 | 3557 | { |
17248569 | 3558 | struct usb_hub *hub = usb_get_intfdata(intf); |
1da177e4 LT |
3559 | struct usb_device *hdev = hub->hdev; |
3560 | unsigned port1; | |
4296c70a | 3561 | int status; |
1da177e4 | 3562 | |
e583d9db AS |
3563 | /* |
3564 | * Warn if children aren't already suspended. | |
3565 | * Also, add up the number of wakeup-enabled descendants. | |
3566 | */ | |
3567 | hub->wakeup_enabled_descendants = 0; | |
1da177e4 | 3568 | for (port1 = 1; port1 <= hdev->maxchild; port1++) { |
d99f6b41 DW |
3569 | struct usb_port *port_dev = hub->ports[port1 - 1]; |
3570 | struct usb_device *udev = port_dev->child; | |
1da177e4 | 3571 | |
6840d255 | 3572 | if (udev && udev->can_submit) { |
b658b8f5 DW |
3573 | dev_warn(&port_dev->dev, "device %s not suspended yet\n", |
3574 | dev_name(&udev->dev)); | |
5b1b0b81 | 3575 | if (PMSG_IS_AUTO(msg)) |
cbb33004 | 3576 | return -EBUSY; |
c9f89fa4 | 3577 | } |
e583d9db AS |
3578 | if (udev) |
3579 | hub->wakeup_enabled_descendants += | |
3580 | wakeup_enabled_descendants(udev); | |
1da177e4 | 3581 | } |
e6f30dea ML |
3582 | |
3583 | if (hdev->do_remote_wakeup && hub->quirk_check_port_auto_suspend) { | |
3584 | /* check if there are changes pending on hub ports */ | |
3585 | if (check_ports_changed(hub)) { | |
3586 | if (PMSG_IS_AUTO(msg)) | |
3587 | return -EBUSY; | |
3588 | pm_wakeup_event(&hdev->dev, 2000); | |
3589 | } | |
3590 | } | |
3591 | ||
4296c70a SS |
3592 | if (hub_is_superspeed(hdev) && hdev->do_remote_wakeup) { |
3593 | /* Enable hub to send remote wakeup for all ports. */ | |
3594 | for (port1 = 1; port1 <= hdev->maxchild; port1++) { | |
3595 | status = set_port_feature(hdev, | |
3596 | port1 | | |
3597 | USB_PORT_FEAT_REMOTE_WAKE_CONNECT | | |
3598 | USB_PORT_FEAT_REMOTE_WAKE_DISCONNECT | | |
3599 | USB_PORT_FEAT_REMOTE_WAKE_OVER_CURRENT, | |
3600 | USB_PORT_FEAT_REMOTE_WAKE_MASK); | |
3601 | } | |
3602 | } | |
1da177e4 | 3603 | |
441b62c1 | 3604 | dev_dbg(&intf->dev, "%s\n", __func__); |
40f122f3 | 3605 | |
37ebb549 | 3606 | /* stop hub_wq and related activity */ |
4330354f | 3607 | hub_quiesce(hub, HUB_SUSPEND); |
b6f6436d | 3608 | return 0; |
1da177e4 LT |
3609 | } |
3610 | ||
3611 | static int hub_resume(struct usb_interface *intf) | |
3612 | { | |
5e6effae | 3613 | struct usb_hub *hub = usb_get_intfdata(intf); |
40f122f3 | 3614 | |
5e6effae | 3615 | dev_dbg(&intf->dev, "%s\n", __func__); |
f2835219 | 3616 | hub_activate(hub, HUB_RESUME); |
1da177e4 LT |
3617 | return 0; |
3618 | } | |
3619 | ||
b41a60ec | 3620 | static int hub_reset_resume(struct usb_interface *intf) |
f07600cf | 3621 | { |
b41a60ec | 3622 | struct usb_hub *hub = usb_get_intfdata(intf); |
f07600cf | 3623 | |
5e6effae | 3624 | dev_dbg(&intf->dev, "%s\n", __func__); |
f2835219 | 3625 | hub_activate(hub, HUB_RESET_RESUME); |
f07600cf AS |
3626 | return 0; |
3627 | } | |
3628 | ||
54515fe5 AS |
3629 | /** |
3630 | * usb_root_hub_lost_power - called by HCD if the root hub lost Vbus power | |
3631 | * @rhdev: struct usb_device for the root hub | |
3632 | * | |
3633 | * The USB host controller driver calls this function when its root hub | |
3634 | * is resumed and Vbus power has been interrupted or the controller | |
feccc30d AS |
3635 | * has been reset. The routine marks @rhdev as having lost power. |
3636 | * When the hub driver is resumed it will take notice and carry out | |
3637 | * power-session recovery for all the "USB-PERSIST"-enabled child devices; | |
3638 | * the others will be disconnected. | |
54515fe5 AS |
3639 | */ |
3640 | void usb_root_hub_lost_power(struct usb_device *rhdev) | |
3641 | { | |
3642 | dev_warn(&rhdev->dev, "root hub lost power or was reset\n"); | |
3643 | rhdev->reset_resume = 1; | |
3644 | } | |
3645 | EXPORT_SYMBOL_GPL(usb_root_hub_lost_power); | |
3646 | ||
1ea7e0e8 SS |
3647 | static const char * const usb3_lpm_names[] = { |
3648 | "U0", | |
3649 | "U1", | |
3650 | "U2", | |
3651 | "U3", | |
3652 | }; | |
3653 | ||
3654 | /* | |
3655 | * Send a Set SEL control transfer to the device, prior to enabling | |
3656 | * device-initiated U1 or U2. This lets the device know the exit latencies from | |
3657 | * the time the device initiates a U1 or U2 exit, to the time it will receive a | |
3658 | * packet from the host. | |
3659 | * | |
3660 | * This function will fail if the SEL or PEL values for udev are greater than | |
3661 | * the maximum allowed values for the link state to be enabled. | |
3662 | */ | |
3663 | static int usb_req_set_sel(struct usb_device *udev, enum usb3_link_state state) | |
3664 | { | |
3665 | struct usb_set_sel_req *sel_values; | |
3666 | unsigned long long u1_sel; | |
3667 | unsigned long long u1_pel; | |
3668 | unsigned long long u2_sel; | |
3669 | unsigned long long u2_pel; | |
3670 | int ret; | |
3671 | ||
38d7f688 XR |
3672 | if (udev->state != USB_STATE_CONFIGURED) |
3673 | return 0; | |
3674 | ||
1ea7e0e8 SS |
3675 | /* Convert SEL and PEL stored in ns to us */ |
3676 | u1_sel = DIV_ROUND_UP(udev->u1_params.sel, 1000); | |
3677 | u1_pel = DIV_ROUND_UP(udev->u1_params.pel, 1000); | |
3678 | u2_sel = DIV_ROUND_UP(udev->u2_params.sel, 1000); | |
3679 | u2_pel = DIV_ROUND_UP(udev->u2_params.pel, 1000); | |
3680 | ||
3681 | /* | |
3682 | * Make sure that the calculated SEL and PEL values for the link | |
3683 | * state we're enabling aren't bigger than the max SEL/PEL | |
3684 | * value that will fit in the SET SEL control transfer. | |
3685 | * Otherwise the device would get an incorrect idea of the exit | |
3686 | * latency for the link state, and could start a device-initiated | |
3687 | * U1/U2 when the exit latencies are too high. | |
3688 | */ | |
3689 | if ((state == USB3_LPM_U1 && | |
3690 | (u1_sel > USB3_LPM_MAX_U1_SEL_PEL || | |
3691 | u1_pel > USB3_LPM_MAX_U1_SEL_PEL)) || | |
3692 | (state == USB3_LPM_U2 && | |
3693 | (u2_sel > USB3_LPM_MAX_U2_SEL_PEL || | |
3694 | u2_pel > USB3_LPM_MAX_U2_SEL_PEL))) { | |
1510a1a2 | 3695 | dev_dbg(&udev->dev, "Device-initiated %s disabled due to long SEL %llu us or PEL %llu us\n", |
1ea7e0e8 SS |
3696 | usb3_lpm_names[state], u1_sel, u1_pel); |
3697 | return -EINVAL; | |
3698 | } | |
3699 | ||
3700 | /* | |
3701 | * If we're enabling device-initiated LPM for one link state, | |
3702 | * but the other link state has a too high SEL or PEL value, | |
3703 | * just set those values to the max in the Set SEL request. | |
3704 | */ | |
3705 | if (u1_sel > USB3_LPM_MAX_U1_SEL_PEL) | |
3706 | u1_sel = USB3_LPM_MAX_U1_SEL_PEL; | |
3707 | ||
3708 | if (u1_pel > USB3_LPM_MAX_U1_SEL_PEL) | |
3709 | u1_pel = USB3_LPM_MAX_U1_SEL_PEL; | |
3710 | ||
3711 | if (u2_sel > USB3_LPM_MAX_U2_SEL_PEL) | |
3712 | u2_sel = USB3_LPM_MAX_U2_SEL_PEL; | |
3713 | ||
3714 | if (u2_pel > USB3_LPM_MAX_U2_SEL_PEL) | |
3715 | u2_pel = USB3_LPM_MAX_U2_SEL_PEL; | |
3716 | ||
3717 | /* | |
3718 | * usb_enable_lpm() can be called as part of a failed device reset, | |
3719 | * which may be initiated by an error path of a mass storage driver. | |
3720 | * Therefore, use GFP_NOIO. | |
3721 | */ | |
3722 | sel_values = kmalloc(sizeof *(sel_values), GFP_NOIO); | |
3723 | if (!sel_values) | |
3724 | return -ENOMEM; | |
3725 | ||
3726 | sel_values->u1_sel = u1_sel; | |
3727 | sel_values->u1_pel = u1_pel; | |
3728 | sel_values->u2_sel = cpu_to_le16(u2_sel); | |
3729 | sel_values->u2_pel = cpu_to_le16(u2_pel); | |
3730 | ||
3731 | ret = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), | |
3732 | USB_REQ_SET_SEL, | |
3733 | USB_RECIP_DEVICE, | |
3734 | 0, 0, | |
3735 | sel_values, sizeof *(sel_values), | |
3736 | USB_CTRL_SET_TIMEOUT); | |
3737 | kfree(sel_values); | |
3738 | return ret; | |
3739 | } | |
3740 | ||
3741 | /* | |
3742 | * Enable or disable device-initiated U1 or U2 transitions. | |
3743 | */ | |
3744 | static int usb_set_device_initiated_lpm(struct usb_device *udev, | |
3745 | enum usb3_link_state state, bool enable) | |
3746 | { | |
3747 | int ret; | |
3748 | int feature; | |
3749 | ||
3750 | switch (state) { | |
3751 | case USB3_LPM_U1: | |
3752 | feature = USB_DEVICE_U1_ENABLE; | |
3753 | break; | |
3754 | case USB3_LPM_U2: | |
3755 | feature = USB_DEVICE_U2_ENABLE; | |
3756 | break; | |
3757 | default: | |
3758 | dev_warn(&udev->dev, "%s: Can't %s non-U1 or U2 state.\n", | |
3759 | __func__, enable ? "enable" : "disable"); | |
3760 | return -EINVAL; | |
3761 | } | |
3762 | ||
3763 | if (udev->state != USB_STATE_CONFIGURED) { | |
3764 | dev_dbg(&udev->dev, "%s: Can't %s %s state " | |
3765 | "for unconfigured device.\n", | |
3766 | __func__, enable ? "enable" : "disable", | |
3767 | usb3_lpm_names[state]); | |
3768 | return 0; | |
3769 | } | |
3770 | ||
3771 | if (enable) { | |
1ea7e0e8 SS |
3772 | /* |
3773 | * Now send the control transfer to enable device-initiated LPM | |
3774 | * for either U1 or U2. | |
3775 | */ | |
3776 | ret = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), | |
3777 | USB_REQ_SET_FEATURE, | |
3778 | USB_RECIP_DEVICE, | |
3779 | feature, | |
3780 | 0, NULL, 0, | |
3781 | USB_CTRL_SET_TIMEOUT); | |
3782 | } else { | |
3783 | ret = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), | |
3784 | USB_REQ_CLEAR_FEATURE, | |
3785 | USB_RECIP_DEVICE, | |
3786 | feature, | |
3787 | 0, NULL, 0, | |
3788 | USB_CTRL_SET_TIMEOUT); | |
3789 | } | |
3790 | if (ret < 0) { | |
3791 | dev_warn(&udev->dev, "%s of device-initiated %s failed.\n", | |
3792 | enable ? "Enable" : "Disable", | |
3793 | usb3_lpm_names[state]); | |
3794 | return -EBUSY; | |
3795 | } | |
3796 | return 0; | |
3797 | } | |
3798 | ||
3799 | static int usb_set_lpm_timeout(struct usb_device *udev, | |
3800 | enum usb3_link_state state, int timeout) | |
3801 | { | |
3802 | int ret; | |
3803 | int feature; | |
3804 | ||
3805 | switch (state) { | |
3806 | case USB3_LPM_U1: | |
3807 | feature = USB_PORT_FEAT_U1_TIMEOUT; | |
3808 | break; | |
3809 | case USB3_LPM_U2: | |
3810 | feature = USB_PORT_FEAT_U2_TIMEOUT; | |
3811 | break; | |
3812 | default: | |
3813 | dev_warn(&udev->dev, "%s: Can't set timeout for non-U1 or U2 state.\n", | |
3814 | __func__); | |
3815 | return -EINVAL; | |
3816 | } | |
3817 | ||
3818 | if (state == USB3_LPM_U1 && timeout > USB3_LPM_U1_MAX_TIMEOUT && | |
3819 | timeout != USB3_LPM_DEVICE_INITIATED) { | |
3820 | dev_warn(&udev->dev, "Failed to set %s timeout to 0x%x, " | |
3821 | "which is a reserved value.\n", | |
3822 | usb3_lpm_names[state], timeout); | |
3823 | return -EINVAL; | |
3824 | } | |
3825 | ||
3826 | ret = set_port_feature(udev->parent, | |
3827 | USB_PORT_LPM_TIMEOUT(timeout) | udev->portnum, | |
3828 | feature); | |
3829 | if (ret < 0) { | |
3830 | dev_warn(&udev->dev, "Failed to set %s timeout to 0x%x," | |
3831 | "error code %i\n", usb3_lpm_names[state], | |
3832 | timeout, ret); | |
3833 | return -EBUSY; | |
3834 | } | |
3835 | if (state == USB3_LPM_U1) | |
3836 | udev->u1_params.timeout = timeout; | |
3837 | else | |
3838 | udev->u2_params.timeout = timeout; | |
3839 | return 0; | |
3840 | } | |
3841 | ||
3842 | /* | |
3843 | * Enable the hub-initiated U1/U2 idle timeouts, and enable device-initiated | |
3844 | * U1/U2 entry. | |
3845 | * | |
3846 | * We will attempt to enable U1 or U2, but there are no guarantees that the | |
3847 | * control transfers to set the hub timeout or enable device-initiated U1/U2 | |
3848 | * will be successful. | |
3849 | * | |
3850 | * If we cannot set the parent hub U1/U2 timeout, we attempt to let the xHCI | |
3851 | * driver know about it. If that call fails, it should be harmless, and just | |
3852 | * take up more slightly more bus bandwidth for unnecessary U1/U2 exit latency. | |
3853 | */ | |
3854 | static void usb_enable_link_state(struct usb_hcd *hcd, struct usb_device *udev, | |
3855 | enum usb3_link_state state) | |
3856 | { | |
65a95b75 | 3857 | int timeout, ret; |
ae8963ad SS |
3858 | __u8 u1_mel = udev->bos->ss_cap->bU1devExitLat; |
3859 | __le16 u2_mel = udev->bos->ss_cap->bU2DevExitLat; | |
3860 | ||
3861 | /* If the device says it doesn't have *any* exit latency to come out of | |
3862 | * U1 or U2, it's probably lying. Assume it doesn't implement that link | |
3863 | * state. | |
3864 | */ | |
3865 | if ((state == USB3_LPM_U1 && u1_mel == 0) || | |
3866 | (state == USB3_LPM_U2 && u2_mel == 0)) | |
3867 | return; | |
1ea7e0e8 | 3868 | |
65a95b75 SS |
3869 | /* |
3870 | * First, let the device know about the exit latencies | |
3871 | * associated with the link state we're about to enable. | |
3872 | */ | |
3873 | ret = usb_req_set_sel(udev, state); | |
3874 | if (ret < 0) { | |
3875 | dev_warn(&udev->dev, "Set SEL for device-initiated %s failed.\n", | |
3876 | usb3_lpm_names[state]); | |
3877 | return; | |
3878 | } | |
3879 | ||
1ea7e0e8 SS |
3880 | /* We allow the host controller to set the U1/U2 timeout internally |
3881 | * first, so that it can change its schedule to account for the | |
3882 | * additional latency to send data to a device in a lower power | |
3883 | * link state. | |
3884 | */ | |
3885 | timeout = hcd->driver->enable_usb3_lpm_timeout(hcd, udev, state); | |
3886 | ||
3887 | /* xHCI host controller doesn't want to enable this LPM state. */ | |
3888 | if (timeout == 0) | |
3889 | return; | |
3890 | ||
3891 | if (timeout < 0) { | |
3892 | dev_warn(&udev->dev, "Could not enable %s link state, " | |
3893 | "xHCI error %i.\n", usb3_lpm_names[state], | |
3894 | timeout); | |
3895 | return; | |
3896 | } | |
3897 | ||
3898 | if (usb_set_lpm_timeout(udev, state, timeout)) | |
3899 | /* If we can't set the parent hub U1/U2 timeout, | |
3900 | * device-initiated LPM won't be allowed either, so let the xHCI | |
3901 | * host know that this link state won't be enabled. | |
3902 | */ | |
3903 | hcd->driver->disable_usb3_lpm_timeout(hcd, udev, state); | |
3904 | ||
3905 | /* Only a configured device will accept the Set Feature U1/U2_ENABLE */ | |
3906 | else if (udev->actconfig) | |
3907 | usb_set_device_initiated_lpm(udev, state, true); | |
3908 | ||
3909 | } | |
3910 | ||
3911 | /* | |
3912 | * Disable the hub-initiated U1/U2 idle timeouts, and disable device-initiated | |
3913 | * U1/U2 entry. | |
3914 | * | |
3915 | * If this function returns -EBUSY, the parent hub will still allow U1/U2 entry. | |
3916 | * If zero is returned, the parent will not allow the link to go into U1/U2. | |
3917 | * | |
3918 | * If zero is returned, device-initiated U1/U2 entry may still be enabled, but | |
3919 | * it won't have an effect on the bus link state because the parent hub will | |
3920 | * still disallow device-initiated U1/U2 entry. | |
3921 | * | |
3922 | * If zero is returned, the xHCI host controller may still think U1/U2 entry is | |
3923 | * possible. The result will be slightly more bus bandwidth will be taken up | |
3924 | * (to account for U1/U2 exit latency), but it should be harmless. | |
3925 | */ | |
3926 | static int usb_disable_link_state(struct usb_hcd *hcd, struct usb_device *udev, | |
3927 | enum usb3_link_state state) | |
3928 | { | |
1ea7e0e8 SS |
3929 | switch (state) { |
3930 | case USB3_LPM_U1: | |
1ea7e0e8 | 3931 | case USB3_LPM_U2: |
1ea7e0e8 SS |
3932 | break; |
3933 | default: | |
3934 | dev_warn(&udev->dev, "%s: Can't disable non-U1 or U2 state.\n", | |
3935 | __func__); | |
3936 | return -EINVAL; | |
3937 | } | |
3938 | ||
3939 | if (usb_set_lpm_timeout(udev, state, 0)) | |
3940 | return -EBUSY; | |
3941 | ||
3942 | usb_set_device_initiated_lpm(udev, state, false); | |
3943 | ||
3944 | if (hcd->driver->disable_usb3_lpm_timeout(hcd, udev, state)) | |
3945 | dev_warn(&udev->dev, "Could not disable xHCI %s timeout, " | |
3946 | "bus schedule bandwidth may be impacted.\n", | |
3947 | usb3_lpm_names[state]); | |
3948 | return 0; | |
3949 | } | |
3950 | ||
3951 | /* | |
3952 | * Disable hub-initiated and device-initiated U1 and U2 entry. | |
3953 | * Caller must own the bandwidth_mutex. | |
3954 | * | |
3955 | * This will call usb_enable_lpm() on failure, which will decrement | |
3956 | * lpm_disable_count, and will re-enable LPM if lpm_disable_count reaches zero. | |
3957 | */ | |
3958 | int usb_disable_lpm(struct usb_device *udev) | |
3959 | { | |
3960 | struct usb_hcd *hcd; | |
3961 | ||
3962 | if (!udev || !udev->parent || | |
3963 | udev->speed != USB_SPEED_SUPER || | |
51df62ff PA |
3964 | !udev->lpm_capable || |
3965 | udev->state < USB_STATE_DEFAULT) | |
1ea7e0e8 SS |
3966 | return 0; |
3967 | ||
3968 | hcd = bus_to_hcd(udev->bus); | |
3969 | if (!hcd || !hcd->driver->disable_usb3_lpm_timeout) | |
3970 | return 0; | |
3971 | ||
3972 | udev->lpm_disable_count++; | |
55558c33 | 3973 | if ((udev->u1_params.timeout == 0 && udev->u2_params.timeout == 0)) |
1ea7e0e8 SS |
3974 | return 0; |
3975 | ||
3976 | /* If LPM is enabled, attempt to disable it. */ | |
3977 | if (usb_disable_link_state(hcd, udev, USB3_LPM_U1)) | |
3978 | goto enable_lpm; | |
3979 | if (usb_disable_link_state(hcd, udev, USB3_LPM_U2)) | |
3980 | goto enable_lpm; | |
3981 | ||
655fe4ef KS |
3982 | udev->usb3_lpm_enabled = 0; |
3983 | ||
1ea7e0e8 SS |
3984 | return 0; |
3985 | ||
3986 | enable_lpm: | |
3987 | usb_enable_lpm(udev); | |
3988 | return -EBUSY; | |
3989 | } | |
3990 | EXPORT_SYMBOL_GPL(usb_disable_lpm); | |
3991 | ||
3992 | /* Grab the bandwidth_mutex before calling usb_disable_lpm() */ | |
3993 | int usb_unlocked_disable_lpm(struct usb_device *udev) | |
3994 | { | |
3995 | struct usb_hcd *hcd = bus_to_hcd(udev->bus); | |
3996 | int ret; | |
3997 | ||
3998 | if (!hcd) | |
3999 | return -EINVAL; | |
4000 | ||
4001 | mutex_lock(hcd->bandwidth_mutex); | |
4002 | ret = usb_disable_lpm(udev); | |
4003 | mutex_unlock(hcd->bandwidth_mutex); | |
4004 | ||
4005 | return ret; | |
4006 | } | |
4007 | EXPORT_SYMBOL_GPL(usb_unlocked_disable_lpm); | |
4008 | ||
4009 | /* | |
4010 | * Attempt to enable device-initiated and hub-initiated U1 and U2 entry. The | |
4011 | * xHCI host policy may prevent U1 or U2 from being enabled. | |
4012 | * | |
4013 | * Other callers may have disabled link PM, so U1 and U2 entry will be disabled | |
4014 | * until the lpm_disable_count drops to zero. Caller must own the | |
4015 | * bandwidth_mutex. | |
4016 | */ | |
4017 | void usb_enable_lpm(struct usb_device *udev) | |
4018 | { | |
4019 | struct usb_hcd *hcd; | |
4020 | ||
4021 | if (!udev || !udev->parent || | |
4022 | udev->speed != USB_SPEED_SUPER || | |
51df62ff PA |
4023 | !udev->lpm_capable || |
4024 | udev->state < USB_STATE_DEFAULT) | |
1ea7e0e8 SS |
4025 | return; |
4026 | ||
4027 | udev->lpm_disable_count--; | |
4028 | hcd = bus_to_hcd(udev->bus); | |
4029 | /* Double check that we can both enable and disable LPM. | |
4030 | * Device must be configured to accept set feature U1/U2 timeout. | |
4031 | */ | |
4032 | if (!hcd || !hcd->driver->enable_usb3_lpm_timeout || | |
4033 | !hcd->driver->disable_usb3_lpm_timeout) | |
4034 | return; | |
4035 | ||
4036 | if (udev->lpm_disable_count > 0) | |
4037 | return; | |
4038 | ||
4039 | usb_enable_link_state(hcd, udev, USB3_LPM_U1); | |
4040 | usb_enable_link_state(hcd, udev, USB3_LPM_U2); | |
655fe4ef KS |
4041 | |
4042 | udev->usb3_lpm_enabled = 1; | |
1ea7e0e8 SS |
4043 | } |
4044 | EXPORT_SYMBOL_GPL(usb_enable_lpm); | |
4045 | ||
4046 | /* Grab the bandwidth_mutex before calling usb_enable_lpm() */ | |
4047 | void usb_unlocked_enable_lpm(struct usb_device *udev) | |
4048 | { | |
4049 | struct usb_hcd *hcd = bus_to_hcd(udev->bus); | |
4050 | ||
4051 | if (!hcd) | |
4052 | return; | |
4053 | ||
4054 | mutex_lock(hcd->bandwidth_mutex); | |
4055 | usb_enable_lpm(udev); | |
4056 | mutex_unlock(hcd->bandwidth_mutex); | |
4057 | } | |
4058 | EXPORT_SYMBOL_GPL(usb_unlocked_enable_lpm); | |
4059 | ||
4060 | ||
d388dab7 AS |
4061 | #else /* CONFIG_PM */ |
4062 | ||
f07600cf AS |
4063 | #define hub_suspend NULL |
4064 | #define hub_resume NULL | |
4065 | #define hub_reset_resume NULL | |
1ea7e0e8 SS |
4066 | |
4067 | int usb_disable_lpm(struct usb_device *udev) | |
4068 | { | |
4069 | return 0; | |
4070 | } | |
e9261fb6 | 4071 | EXPORT_SYMBOL_GPL(usb_disable_lpm); |
1ea7e0e8 SS |
4072 | |
4073 | void usb_enable_lpm(struct usb_device *udev) { } | |
e9261fb6 | 4074 | EXPORT_SYMBOL_GPL(usb_enable_lpm); |
1ea7e0e8 SS |
4075 | |
4076 | int usb_unlocked_disable_lpm(struct usb_device *udev) | |
4077 | { | |
4078 | return 0; | |
4079 | } | |
e9261fb6 | 4080 | EXPORT_SYMBOL_GPL(usb_unlocked_disable_lpm); |
1ea7e0e8 SS |
4081 | |
4082 | void usb_unlocked_enable_lpm(struct usb_device *udev) { } | |
e9261fb6 | 4083 | EXPORT_SYMBOL_GPL(usb_unlocked_enable_lpm); |
f74631e3 SS |
4084 | |
4085 | int usb_disable_ltm(struct usb_device *udev) | |
4086 | { | |
4087 | return 0; | |
4088 | } | |
4089 | EXPORT_SYMBOL_GPL(usb_disable_ltm); | |
4090 | ||
4091 | void usb_enable_ltm(struct usb_device *udev) { } | |
4092 | EXPORT_SYMBOL_GPL(usb_enable_ltm); | |
c4b51a43 | 4093 | |
4a95b1fc SR |
4094 | static int hub_handle_remote_wakeup(struct usb_hub *hub, unsigned int port, |
4095 | u16 portstatus, u16 portchange) | |
4096 | { | |
4097 | return 0; | |
4098 | } | |
4099 | ||
c4b51a43 | 4100 | #endif /* CONFIG_PM */ |
d388dab7 | 4101 | |
1da177e4 LT |
4102 | |
4103 | /* USB 2.0 spec, 7.1.7.3 / fig 7-29: | |
4104 | * | |
4105 | * Between connect detection and reset signaling there must be a delay | |
4106 | * of 100ms at least for debounce and power-settling. The corresponding | |
4107 | * timer shall restart whenever the downstream port detects a disconnect. | |
469271f8 | 4108 | * |
1da177e4 LT |
4109 | * Apparently there are some bluetooth and irda-dongles and a number of |
4110 | * low-speed devices for which this debounce period may last over a second. | |
4111 | * Not covered by the spec - but easy to deal with. | |
4112 | * | |
4113 | * This implementation uses a 1500ms total debounce timeout; if the | |
4114 | * connection isn't stable by then it returns -ETIMEDOUT. It checks | |
4115 | * every 25ms for transient disconnects. When the port status has been | |
4116 | * unchanged for 100ms it returns the port status. | |
4117 | */ | |
ad493e5e | 4118 | int hub_port_debounce(struct usb_hub *hub, int port1, bool must_be_connected) |
1da177e4 LT |
4119 | { |
4120 | int ret; | |
1da177e4 LT |
4121 | u16 portchange, portstatus; |
4122 | unsigned connection = 0xffff; | |
d99f6b41 DW |
4123 | int total_time, stable_time = 0; |
4124 | struct usb_port *port_dev = hub->ports[port1 - 1]; | |
1da177e4 LT |
4125 | |
4126 | for (total_time = 0; ; total_time += HUB_DEBOUNCE_STEP) { | |
4127 | ret = hub_port_status(hub, port1, &portstatus, &portchange); | |
4128 | if (ret < 0) | |
4129 | return ret; | |
4130 | ||
4131 | if (!(portchange & USB_PORT_STAT_C_CONNECTION) && | |
4132 | (portstatus & USB_PORT_STAT_CONNECTION) == connection) { | |
ad493e5e LT |
4133 | if (!must_be_connected || |
4134 | (connection == USB_PORT_STAT_CONNECTION)) | |
4135 | stable_time += HUB_DEBOUNCE_STEP; | |
1da177e4 LT |
4136 | if (stable_time >= HUB_DEBOUNCE_STABLE) |
4137 | break; | |
4138 | } else { | |
4139 | stable_time = 0; | |
4140 | connection = portstatus & USB_PORT_STAT_CONNECTION; | |
4141 | } | |
4142 | ||
4143 | if (portchange & USB_PORT_STAT_C_CONNECTION) { | |
ad493e5e | 4144 | usb_clear_port_feature(hub->hdev, port1, |
1da177e4 LT |
4145 | USB_PORT_FEAT_C_CONNECTION); |
4146 | } | |
4147 | ||
4148 | if (total_time >= HUB_DEBOUNCE_TIMEOUT) | |
4149 | break; | |
4150 | msleep(HUB_DEBOUNCE_STEP); | |
4151 | } | |
4152 | ||
d99f6b41 DW |
4153 | dev_dbg(&port_dev->dev, "debounce total %dms stable %dms status 0x%x\n", |
4154 | total_time, stable_time, portstatus); | |
1da177e4 LT |
4155 | |
4156 | if (stable_time < HUB_DEBOUNCE_STABLE) | |
4157 | return -ETIMEDOUT; | |
4158 | return portstatus; | |
4159 | } | |
4160 | ||
fc721f51 | 4161 | void usb_ep0_reinit(struct usb_device *udev) |
1da177e4 | 4162 | { |
ddeac4e7 AS |
4163 | usb_disable_endpoint(udev, 0 + USB_DIR_IN, true); |
4164 | usb_disable_endpoint(udev, 0 + USB_DIR_OUT, true); | |
2caf7fcd | 4165 | usb_enable_endpoint(udev, &udev->ep0, true); |
1da177e4 | 4166 | } |
fc721f51 | 4167 | EXPORT_SYMBOL_GPL(usb_ep0_reinit); |
1da177e4 LT |
4168 | |
4169 | #define usb_sndaddr0pipe() (PIPE_CONTROL << 30) | |
4170 | #define usb_rcvaddr0pipe() ((PIPE_CONTROL << 30) | USB_DIR_IN) | |
4171 | ||
4326ed0b | 4172 | static int hub_set_address(struct usb_device *udev, int devnum) |
1da177e4 LT |
4173 | { |
4174 | int retval; | |
c6515272 | 4175 | struct usb_hcd *hcd = bus_to_hcd(udev->bus); |
1da177e4 | 4176 | |
c6515272 SS |
4177 | /* |
4178 | * The host controller will choose the device address, | |
4179 | * instead of the core having chosen it earlier | |
4180 | */ | |
4181 | if (!hcd->driver->address_device && devnum <= 1) | |
1da177e4 LT |
4182 | return -EINVAL; |
4183 | if (udev->state == USB_STATE_ADDRESS) | |
4184 | return 0; | |
4185 | if (udev->state != USB_STATE_DEFAULT) | |
4186 | return -EINVAL; | |
c8d4af8e | 4187 | if (hcd->driver->address_device) |
c6515272 | 4188 | retval = hcd->driver->address_device(hcd, udev); |
c8d4af8e | 4189 | else |
c6515272 SS |
4190 | retval = usb_control_msg(udev, usb_sndaddr0pipe(), |
4191 | USB_REQ_SET_ADDRESS, 0, devnum, 0, | |
4192 | NULL, 0, USB_CTRL_SET_TIMEOUT); | |
1da177e4 | 4193 | if (retval == 0) { |
3b29b68b | 4194 | update_devnum(udev, devnum); |
4953d141 | 4195 | /* Device now using proper address. */ |
1da177e4 | 4196 | usb_set_device_state(udev, USB_STATE_ADDRESS); |
fc721f51 | 4197 | usb_ep0_reinit(udev); |
1da177e4 LT |
4198 | } |
4199 | return retval; | |
4200 | } | |
4201 | ||
890dae88 MN |
4202 | /* |
4203 | * There are reports of USB 3.0 devices that say they support USB 2.0 Link PM | |
4204 | * when they're plugged into a USB 2.0 port, but they don't work when LPM is | |
4205 | * enabled. | |
4206 | * | |
4207 | * Only enable USB 2.0 Link PM if the port is internal (hardwired), or the | |
4208 | * device says it supports the new USB 2.0 Link PM errata by setting the BESL | |
4209 | * support bit in the BOS descriptor. | |
4210 | */ | |
4211 | static void hub_set_initial_usb2_lpm_policy(struct usb_device *udev) | |
4212 | { | |
d99f6b41 DW |
4213 | struct usb_hub *hub = usb_hub_to_struct_hub(udev->parent); |
4214 | int connect_type = USB_PORT_CONNECT_TYPE_UNKNOWN; | |
890dae88 MN |
4215 | |
4216 | if (!udev->usb2_hw_lpm_capable) | |
4217 | return; | |
4218 | ||
d99f6b41 DW |
4219 | if (hub) |
4220 | connect_type = hub->ports[udev->portnum - 1]->connect_type; | |
890dae88 | 4221 | |
23c05820 | 4222 | if ((udev->bos->ext_cap->bmAttributes & cpu_to_le32(USB_BESL_SUPPORT)) || |
890dae88 MN |
4223 | connect_type == USB_PORT_CONNECT_TYPE_HARD_WIRED) { |
4224 | udev->usb2_hw_lpm_allowed = 1; | |
4225 | usb_set_usb2_hardware_lpm(udev, 1); | |
4226 | } | |
4227 | } | |
4228 | ||
48fc7dbd DW |
4229 | static int hub_enable_device(struct usb_device *udev) |
4230 | { | |
4231 | struct usb_hcd *hcd = bus_to_hcd(udev->bus); | |
4232 | ||
4233 | if (!hcd->driver->enable_device) | |
4234 | return 0; | |
4235 | if (udev->state == USB_STATE_ADDRESS) | |
4236 | return 0; | |
4237 | if (udev->state != USB_STATE_DEFAULT) | |
4238 | return -EINVAL; | |
4239 | ||
4240 | return hcd->driver->enable_device(hcd, udev); | |
4241 | } | |
4242 | ||
1da177e4 LT |
4243 | /* Reset device, (re)assign address, get device descriptor. |
4244 | * Device connection must be stable, no more debouncing needed. | |
4245 | * Returns device in USB_STATE_ADDRESS, except on error. | |
4246 | * | |
4247 | * If this is called for an already-existing device (as part of | |
5c79a1e3 DW |
4248 | * usb_reset_and_verify_device), the caller must own the device lock and |
4249 | * the port lock. For a newly detected device that is not accessible | |
4250 | * through any global pointers, it's not necessary to lock the device, | |
4251 | * but it is still necessary to lock the port. | |
1da177e4 LT |
4252 | */ |
4253 | static int | |
039b3307 | 4254 | hub_port_init(struct usb_hub *hub, struct usb_device *udev, int port1, |
1da177e4 LT |
4255 | int retry_counter) |
4256 | { | |
1da177e4 | 4257 | struct usb_device *hdev = hub->hdev; |
e7b77172 | 4258 | struct usb_hcd *hcd = bus_to_hcd(hdev->bus); |
1da177e4 LT |
4259 | int i, j, retval; |
4260 | unsigned delay = HUB_SHORT_RESET_TIME; | |
4261 | enum usb_device_speed oldspeed = udev->speed; | |
e538dfda | 4262 | const char *speed; |
4326ed0b | 4263 | int devnum = udev->devnum; |
1da177e4 LT |
4264 | |
4265 | /* root hub ports have a slightly longer reset period | |
4266 | * (from USB 2.0 spec, section 7.1.7.5) | |
4267 | */ | |
4268 | if (!hdev->parent) { | |
4269 | delay = HUB_ROOT_RESET_TIME; | |
4270 | if (port1 == hdev->bus->otg_port) | |
4271 | hdev->bus->b_hnp_enable = 0; | |
4272 | } | |
4273 | ||
4274 | /* Some low speed devices have problems with the quick delay, so */ | |
4275 | /* be a bit pessimistic with those devices. RHbug #23670 */ | |
4276 | if (oldspeed == USB_SPEED_LOW) | |
4277 | delay = HUB_LONG_RESET_TIME; | |
4278 | ||
6fecd4f2 | 4279 | mutex_lock(&hdev->bus->usb_address0_mutex); |
1da177e4 | 4280 | |
07194ab7 LT |
4281 | /* Reset the device; full speed may morph to high speed */ |
4282 | /* FIXME a USB 2.0 device may morph into SuperSpeed on reset. */ | |
75d7cf72 | 4283 | retval = hub_port_reset(hub, port1, udev, delay, false); |
07194ab7 LT |
4284 | if (retval < 0) /* error or disconnect */ |
4285 | goto fail; | |
4286 | /* success, speed is known */ | |
4287 | ||
1da177e4 LT |
4288 | retval = -ENODEV; |
4289 | ||
4290 | if (oldspeed != USB_SPEED_UNKNOWN && oldspeed != udev->speed) { | |
4291 | dev_dbg(&udev->dev, "device reset changed speed!\n"); | |
4292 | goto fail; | |
4293 | } | |
4294 | oldspeed = udev->speed; | |
4326ed0b | 4295 | |
1da177e4 LT |
4296 | /* USB 2.0 section 5.5.3 talks about ep0 maxpacket ... |
4297 | * it's fixed size except for full speed devices. | |
5bb6e0ae IPG |
4298 | * For Wireless USB devices, ep0 max packet is always 512 (tho |
4299 | * reported as 0xff in the device descriptor). WUSB1.0[4.8.1]. | |
1da177e4 LT |
4300 | */ |
4301 | switch (udev->speed) { | |
6b403b02 | 4302 | case USB_SPEED_SUPER: |
551cdbbe | 4303 | case USB_SPEED_WIRELESS: /* fixed at 512 */ |
551509d2 | 4304 | udev->ep0.desc.wMaxPacketSize = cpu_to_le16(512); |
5bb6e0ae | 4305 | break; |
1da177e4 | 4306 | case USB_SPEED_HIGH: /* fixed at 64 */ |
551509d2 | 4307 | udev->ep0.desc.wMaxPacketSize = cpu_to_le16(64); |
1da177e4 LT |
4308 | break; |
4309 | case USB_SPEED_FULL: /* 8, 16, 32, or 64 */ | |
4310 | /* to determine the ep0 maxpacket size, try to read | |
4311 | * the device descriptor to get bMaxPacketSize0 and | |
4312 | * then correct our initial guess. | |
4313 | */ | |
551509d2 | 4314 | udev->ep0.desc.wMaxPacketSize = cpu_to_le16(64); |
1da177e4 LT |
4315 | break; |
4316 | case USB_SPEED_LOW: /* fixed at 8 */ | |
551509d2 | 4317 | udev->ep0.desc.wMaxPacketSize = cpu_to_le16(8); |
1da177e4 LT |
4318 | break; |
4319 | default: | |
4320 | goto fail; | |
4321 | } | |
e538dfda MN |
4322 | |
4323 | if (udev->speed == USB_SPEED_WIRELESS) | |
4324 | speed = "variable speed Wireless"; | |
4325 | else | |
4326 | speed = usb_speed_string(udev->speed); | |
4327 | ||
c6515272 SS |
4328 | if (udev->speed != USB_SPEED_SUPER) |
4329 | dev_info(&udev->dev, | |
e538dfda MN |
4330 | "%s %s USB device number %d using %s\n", |
4331 | (udev->config) ? "reset" : "new", speed, | |
3b29b68b | 4332 | devnum, udev->bus->controller->driver->name); |
1da177e4 LT |
4333 | |
4334 | /* Set up TT records, if needed */ | |
4335 | if (hdev->tt) { | |
4336 | udev->tt = hdev->tt; | |
4337 | udev->ttport = hdev->ttport; | |
4338 | } else if (udev->speed != USB_SPEED_HIGH | |
4339 | && hdev->speed == USB_SPEED_HIGH) { | |
d199c96d AS |
4340 | if (!hub->tt.hub) { |
4341 | dev_err(&udev->dev, "parent hub has no TT\n"); | |
4342 | retval = -EINVAL; | |
4343 | goto fail; | |
4344 | } | |
1da177e4 LT |
4345 | udev->tt = &hub->tt; |
4346 | udev->ttport = port1; | |
4347 | } | |
469271f8 | 4348 | |
1da177e4 LT |
4349 | /* Why interleave GET_DESCRIPTOR and SET_ADDRESS this way? |
4350 | * Because device hardware and firmware is sometimes buggy in | |
4351 | * this area, and this is how Linux has done it for ages. | |
4352 | * Change it cautiously. | |
4353 | * | |
48fc7dbd | 4354 | * NOTE: If use_new_scheme() is true we will start by issuing |
1da177e4 LT |
4355 | * a 64-byte GET_DESCRIPTOR request. This is what Windows does, |
4356 | * so it may help with some non-standards-compliant devices. | |
4357 | * Otherwise we start with SET_ADDRESS and then try to read the | |
4358 | * first 8 bytes of the device descriptor to get the ep0 maxpacket | |
4359 | * value. | |
4360 | */ | |
4361 | for (i = 0; i < GET_DESCRIPTOR_TRIES; (++i, msleep(100))) { | |
48fc7dbd DW |
4362 | bool did_new_scheme = false; |
4363 | ||
4364 | if (use_new_scheme(udev, retry_counter)) { | |
1da177e4 LT |
4365 | struct usb_device_descriptor *buf; |
4366 | int r = 0; | |
4367 | ||
48fc7dbd DW |
4368 | did_new_scheme = true; |
4369 | retval = hub_enable_device(udev); | |
938569eb ON |
4370 | if (retval < 0) { |
4371 | dev_err(&udev->dev, | |
4372 | "hub failed to enable device, error %d\n", | |
4373 | retval); | |
48fc7dbd | 4374 | goto fail; |
938569eb | 4375 | } |
48fc7dbd | 4376 | |
1da177e4 LT |
4377 | #define GET_DESCRIPTOR_BUFSIZE 64 |
4378 | buf = kmalloc(GET_DESCRIPTOR_BUFSIZE, GFP_NOIO); | |
4379 | if (!buf) { | |
4380 | retval = -ENOMEM; | |
4381 | continue; | |
4382 | } | |
4383 | ||
b89ee19a AS |
4384 | /* Retry on all errors; some devices are flakey. |
4385 | * 255 is for WUSB devices, we actually need to use | |
4386 | * 512 (WUSB1.0[4.8.1]). | |
1da177e4 LT |
4387 | */ |
4388 | for (j = 0; j < 3; ++j) { | |
4389 | buf->bMaxPacketSize0 = 0; | |
4390 | r = usb_control_msg(udev, usb_rcvaddr0pipe(), | |
4391 | USB_REQ_GET_DESCRIPTOR, USB_DIR_IN, | |
4392 | USB_DT_DEVICE << 8, 0, | |
4393 | buf, GET_DESCRIPTOR_BUFSIZE, | |
fd7c519d | 4394 | initial_descriptor_timeout); |
1da177e4 | 4395 | switch (buf->bMaxPacketSize0) { |
5bb6e0ae | 4396 | case 8: case 16: case 32: case 64: case 255: |
1da177e4 LT |
4397 | if (buf->bDescriptorType == |
4398 | USB_DT_DEVICE) { | |
4399 | r = 0; | |
4400 | break; | |
4401 | } | |
4402 | /* FALL THROUGH */ | |
4403 | default: | |
4404 | if (r == 0) | |
4405 | r = -EPROTO; | |
4406 | break; | |
4407 | } | |
4408 | if (r == 0) | |
4409 | break; | |
4410 | } | |
4411 | udev->descriptor.bMaxPacketSize0 = | |
4412 | buf->bMaxPacketSize0; | |
4413 | kfree(buf); | |
4414 | ||
75d7cf72 | 4415 | retval = hub_port_reset(hub, port1, udev, delay, false); |
1da177e4 LT |
4416 | if (retval < 0) /* error or disconnect */ |
4417 | goto fail; | |
4418 | if (oldspeed != udev->speed) { | |
4419 | dev_dbg(&udev->dev, | |
4420 | "device reset changed speed!\n"); | |
4421 | retval = -ENODEV; | |
4422 | goto fail; | |
4423 | } | |
4424 | if (r) { | |
e9e88fb7 AS |
4425 | if (r != -ENODEV) |
4426 | dev_err(&udev->dev, "device descriptor read/64, error %d\n", | |
4427 | r); | |
1da177e4 LT |
4428 | retval = -EMSGSIZE; |
4429 | continue; | |
4430 | } | |
4431 | #undef GET_DESCRIPTOR_BUFSIZE | |
4432 | } | |
4433 | ||
469271f8 MB |
4434 | /* |
4435 | * If device is WUSB, we already assigned an | |
4436 | * unauthorized address in the Connect Ack sequence; | |
4437 | * authorization will assign the final address. | |
4438 | */ | |
c6515272 | 4439 | if (udev->wusb == 0) { |
6c529cdc IPG |
4440 | for (j = 0; j < SET_ADDRESS_TRIES; ++j) { |
4441 | retval = hub_set_address(udev, devnum); | |
4442 | if (retval >= 0) | |
4443 | break; | |
4444 | msleep(200); | |
4445 | } | |
4446 | if (retval < 0) { | |
e9e88fb7 AS |
4447 | if (retval != -ENODEV) |
4448 | dev_err(&udev->dev, "device not accepting address %d, error %d\n", | |
4449 | devnum, retval); | |
6c529cdc IPG |
4450 | goto fail; |
4451 | } | |
c6515272 SS |
4452 | if (udev->speed == USB_SPEED_SUPER) { |
4453 | devnum = udev->devnum; | |
4454 | dev_info(&udev->dev, | |
3b29b68b | 4455 | "%s SuperSpeed USB device number %d using %s\n", |
c6515272 | 4456 | (udev->config) ? "reset" : "new", |
3b29b68b | 4457 | devnum, udev->bus->controller->driver->name); |
c6515272 | 4458 | } |
6c529cdc IPG |
4459 | |
4460 | /* cope with hardware quirkiness: | |
4461 | * - let SET_ADDRESS settle, some device hardware wants it | |
4462 | * - read ep0 maxpacket even for high and low speed, | |
4463 | */ | |
4464 | msleep(10); | |
48fc7dbd DW |
4465 | /* use_new_scheme() checks the speed which may have |
4466 | * changed since the initial look so we cache the result | |
4467 | * in did_new_scheme | |
4468 | */ | |
4469 | if (did_new_scheme) | |
1da177e4 | 4470 | break; |
469271f8 | 4471 | } |
1da177e4 LT |
4472 | |
4473 | retval = usb_get_device_descriptor(udev, 8); | |
4474 | if (retval < 8) { | |
e9e88fb7 AS |
4475 | if (retval != -ENODEV) |
4476 | dev_err(&udev->dev, | |
b9cef6c3 WF |
4477 | "device descriptor read/8, error %d\n", |
4478 | retval); | |
1da177e4 LT |
4479 | if (retval >= 0) |
4480 | retval = -EMSGSIZE; | |
4481 | } else { | |
4482 | retval = 0; | |
4483 | break; | |
4484 | } | |
4485 | } | |
4486 | if (retval) | |
4487 | goto fail; | |
4488 | ||
d8aec3db EF |
4489 | /* |
4490 | * Some superspeed devices have finished the link training process | |
4491 | * and attached to a superspeed hub port, but the device descriptor | |
4492 | * got from those devices show they aren't superspeed devices. Warm | |
4493 | * reset the port attached by the devices can fix them. | |
4494 | */ | |
4495 | if ((udev->speed == USB_SPEED_SUPER) && | |
4496 | (le16_to_cpu(udev->descriptor.bcdUSB) < 0x0300)) { | |
4497 | dev_err(&udev->dev, "got a wrong device descriptor, " | |
4498 | "warm reset device\n"); | |
4499 | hub_port_reset(hub, port1, udev, | |
4500 | HUB_BH_RESET_TIME, true); | |
4501 | retval = -EINVAL; | |
4502 | goto fail; | |
4503 | } | |
4504 | ||
6b403b02 SS |
4505 | if (udev->descriptor.bMaxPacketSize0 == 0xff || |
4506 | udev->speed == USB_SPEED_SUPER) | |
4507 | i = 512; | |
4508 | else | |
4509 | i = udev->descriptor.bMaxPacketSize0; | |
29cc8897 | 4510 | if (usb_endpoint_maxp(&udev->ep0.desc) != i) { |
56626a72 | 4511 | if (udev->speed == USB_SPEED_LOW || |
1da177e4 | 4512 | !(i == 8 || i == 16 || i == 32 || i == 64)) { |
56626a72 | 4513 | dev_err(&udev->dev, "Invalid ep0 maxpacket: %d\n", i); |
1da177e4 LT |
4514 | retval = -EMSGSIZE; |
4515 | goto fail; | |
4516 | } | |
56626a72 AS |
4517 | if (udev->speed == USB_SPEED_FULL) |
4518 | dev_dbg(&udev->dev, "ep0 maxpacket = %d\n", i); | |
4519 | else | |
4520 | dev_warn(&udev->dev, "Using ep0 maxpacket: %d\n", i); | |
1da177e4 | 4521 | udev->ep0.desc.wMaxPacketSize = cpu_to_le16(i); |
fc721f51 | 4522 | usb_ep0_reinit(udev); |
1da177e4 | 4523 | } |
469271f8 | 4524 | |
1da177e4 LT |
4525 | retval = usb_get_device_descriptor(udev, USB_DT_DEVICE_SIZE); |
4526 | if (retval < (signed)sizeof(udev->descriptor)) { | |
e9e88fb7 AS |
4527 | if (retval != -ENODEV) |
4528 | dev_err(&udev->dev, "device descriptor read/all, error %d\n", | |
4529 | retval); | |
1da177e4 LT |
4530 | if (retval >= 0) |
4531 | retval = -ENOMSG; | |
4532 | goto fail; | |
4533 | } | |
4534 | ||
ad87e032 AS |
4535 | usb_detect_quirks(udev); |
4536 | ||
1ff4df56 AX |
4537 | if (udev->wusb == 0 && le16_to_cpu(udev->descriptor.bcdUSB) >= 0x0201) { |
4538 | retval = usb_get_bos_descriptor(udev); | |
51e0a012 | 4539 | if (!retval) { |
d9b2099c | 4540 | udev->lpm_capable = usb_device_supports_lpm(udev); |
51e0a012 SS |
4541 | usb_set_lpm_parameters(udev); |
4542 | } | |
1ff4df56 | 4543 | } |
3148bf04 | 4544 | |
1da177e4 | 4545 | retval = 0; |
48f24970 AD |
4546 | /* notify HCD that we have a device connected and addressed */ |
4547 | if (hcd->driver->update_device) | |
4548 | hcd->driver->update_device(hcd, udev); | |
890dae88 | 4549 | hub_set_initial_usb2_lpm_policy(udev); |
1da177e4 | 4550 | fail: |
4326ed0b | 4551 | if (retval) { |
1da177e4 | 4552 | hub_port_disable(hub, port1, 0); |
3b29b68b | 4553 | update_devnum(udev, devnum); /* for disconnect processing */ |
4326ed0b | 4554 | } |
6fecd4f2 | 4555 | mutex_unlock(&hdev->bus->usb_address0_mutex); |
1da177e4 LT |
4556 | return retval; |
4557 | } | |
4558 | ||
4559 | static void | |
039b3307 | 4560 | check_highspeed(struct usb_hub *hub, struct usb_device *udev, int port1) |
1da177e4 LT |
4561 | { |
4562 | struct usb_qualifier_descriptor *qual; | |
4563 | int status; | |
4564 | ||
2a159389 JH |
4565 | if (udev->quirks & USB_QUIRK_DEVICE_QUALIFIER) |
4566 | return; | |
4567 | ||
039b3307 | 4568 | qual = kmalloc(sizeof *qual, GFP_KERNEL); |
1da177e4 LT |
4569 | if (qual == NULL) |
4570 | return; | |
4571 | ||
039b3307 | 4572 | status = usb_get_descriptor(udev, USB_DT_DEVICE_QUALIFIER, 0, |
1da177e4 LT |
4573 | qual, sizeof *qual); |
4574 | if (status == sizeof *qual) { | |
4575 | dev_info(&udev->dev, "not running at top speed; " | |
4576 | "connect to a high speed hub\n"); | |
4577 | /* hub LEDs are probably harder to miss than syslog */ | |
4578 | if (hub->has_indicators) { | |
4579 | hub->indicator[port1-1] = INDICATOR_GREEN_BLINK; | |
22f6a0f0 SD |
4580 | queue_delayed_work(system_power_efficient_wq, |
4581 | &hub->leds, 0); | |
1da177e4 LT |
4582 | } |
4583 | } | |
1bc3c9e1 | 4584 | kfree(qual); |
1da177e4 LT |
4585 | } |
4586 | ||
4587 | static unsigned | |
039b3307 | 4588 | hub_power_remaining(struct usb_hub *hub) |
1da177e4 LT |
4589 | { |
4590 | struct usb_device *hdev = hub->hdev; | |
4591 | int remaining; | |
55c52718 | 4592 | int port1; |
1da177e4 | 4593 | |
55c52718 | 4594 | if (!hub->limited_power) |
1da177e4 LT |
4595 | return 0; |
4596 | ||
55c52718 AS |
4597 | remaining = hdev->bus_mA - hub->descriptor->bHubContrCurrent; |
4598 | for (port1 = 1; port1 <= hdev->maxchild; ++port1) { | |
d99f6b41 DW |
4599 | struct usb_port *port_dev = hub->ports[port1 - 1]; |
4600 | struct usb_device *udev = port_dev->child; | |
4601 | unsigned unit_load; | |
4602 | int delta; | |
1da177e4 LT |
4603 | |
4604 | if (!udev) | |
4605 | continue; | |
430ee58e SAS |
4606 | if (hub_is_superspeed(udev)) |
4607 | unit_load = 150; | |
4608 | else | |
4609 | unit_load = 100; | |
1da177e4 | 4610 | |
430ee58e SAS |
4611 | /* |
4612 | * Unconfigured devices may not use more than one unit load, | |
4613 | * or 8mA for OTG ports | |
4614 | */ | |
1da177e4 | 4615 | if (udev->actconfig) |
8d8479db | 4616 | delta = usb_get_max_power(udev, udev->actconfig); |
55c52718 | 4617 | else if (port1 != udev->bus->otg_port || hdev->parent) |
430ee58e | 4618 | delta = unit_load; |
1da177e4 | 4619 | else |
55c52718 AS |
4620 | delta = 8; |
4621 | if (delta > hub->mA_per_port) | |
d99f6b41 DW |
4622 | dev_warn(&port_dev->dev, "%dmA is over %umA budget!\n", |
4623 | delta, hub->mA_per_port); | |
1da177e4 LT |
4624 | remaining -= delta; |
4625 | } | |
4626 | if (remaining < 0) { | |
55c52718 | 4627 | dev_warn(hub->intfdev, "%dmA over power budget!\n", |
469271f8 | 4628 | -remaining); |
1da177e4 LT |
4629 | remaining = 0; |
4630 | } | |
4631 | return remaining; | |
4632 | } | |
4633 | ||
af376a46 DW |
4634 | static void hub_port_connect(struct usb_hub *hub, int port1, u16 portstatus, |
4635 | u16 portchange) | |
1da177e4 | 4636 | { |
1da177e4 | 4637 | int status, i; |
430ee58e | 4638 | unsigned unit_load; |
1da177e4 | 4639 | struct usb_device *hdev = hub->hdev; |
90da096e | 4640 | struct usb_hcd *hcd = bus_to_hcd(hdev->bus); |
d99f6b41 | 4641 | struct usb_port *port_dev = hub->ports[port1 - 1]; |
af376a46 | 4642 | struct usb_device *udev = port_dev->child; |
5ee0f803 | 4643 | static int unreliable_port = -1; |
8808f00c | 4644 | |
24618b0c | 4645 | /* Disconnect any existing devices under this port */ |
b76baa81 | 4646 | if (udev) { |
b2108f1e | 4647 | if (hcd->usb_phy && !hdev->parent) |
3d46e73d | 4648 | usb_phy_notify_disconnect(hcd->usb_phy, udev->speed); |
d99f6b41 | 4649 | usb_disconnect(&port_dev->child); |
b76baa81 | 4650 | } |
24618b0c | 4651 | |
253e0572 AS |
4652 | /* We can forget about a "removed" device when there's a physical |
4653 | * disconnect or the connect status changes. | |
4654 | */ | |
4655 | if (!(portstatus & USB_PORT_STAT_CONNECTION) || | |
4656 | (portchange & USB_PORT_STAT_C_CONNECTION)) | |
4657 | clear_bit(port1, hub->removed_bits); | |
4658 | ||
5257d97a AS |
4659 | if (portchange & (USB_PORT_STAT_C_CONNECTION | |
4660 | USB_PORT_STAT_C_ENABLE)) { | |
ad493e5e | 4661 | status = hub_port_debounce_be_stable(hub, port1); |
5257d97a | 4662 | if (status < 0) { |
5ee0f803 ON |
4663 | if (status != -ENODEV && |
4664 | port1 != unreliable_port && | |
4665 | printk_ratelimit()) | |
dd5f5006 | 4666 | dev_err(&port_dev->dev, "connect-debounce failed\n"); |
5257d97a | 4667 | portstatus &= ~USB_PORT_STAT_CONNECTION; |
5ee0f803 | 4668 | unreliable_port = port1; |
5257d97a AS |
4669 | } else { |
4670 | portstatus = status; | |
4671 | } | |
4672 | } | |
4673 | ||
253e0572 AS |
4674 | /* Return now if debouncing failed or nothing is connected or |
4675 | * the device was "removed". | |
4676 | */ | |
4677 | if (!(portstatus & USB_PORT_STAT_CONNECTION) || | |
4678 | test_bit(port1, hub->removed_bits)) { | |
1da177e4 | 4679 | |
fbaecff0 DD |
4680 | /* |
4681 | * maybe switch power back on (e.g. root hub was reset) | |
4682 | * but only if the port isn't owned by someone else. | |
4683 | */ | |
9262c19d | 4684 | if (hub_is_port_power_switchable(hub) |
fbaecff0 DD |
4685 | && !port_is_power_on(hub, portstatus) |
4686 | && !port_dev->port_owner) | |
1da177e4 | 4687 | set_port_feature(hdev, port1, USB_PORT_FEAT_POWER); |
5257d97a | 4688 | |
1da177e4 | 4689 | if (portstatus & USB_PORT_STAT_ENABLE) |
469271f8 | 4690 | goto done; |
1da177e4 LT |
4691 | return; |
4692 | } | |
430ee58e SAS |
4693 | if (hub_is_superspeed(hub->hdev)) |
4694 | unit_load = 150; | |
4695 | else | |
4696 | unit_load = 100; | |
1da177e4 | 4697 | |
e9e88fb7 | 4698 | status = 0; |
1da177e4 | 4699 | for (i = 0; i < SET_CONFIG_TRIES; i++) { |
1da177e4 LT |
4700 | |
4701 | /* reallocate for each attempt, since references | |
4702 | * to the previous one can escape in various ways | |
4703 | */ | |
4704 | udev = usb_alloc_dev(hdev, hdev->bus, port1); | |
4705 | if (!udev) { | |
d99f6b41 DW |
4706 | dev_err(&port_dev->dev, |
4707 | "couldn't allocate usb_device\n"); | |
1da177e4 LT |
4708 | goto done; |
4709 | } | |
4710 | ||
4711 | usb_set_device_state(udev, USB_STATE_POWERED); | |
469271f8 | 4712 | udev->bus_mA = hub->mA_per_port; |
b6956ffa | 4713 | udev->level = hdev->level + 1; |
8af548dc | 4714 | udev->wusb = hub_is_wusb(hub); |
55c52718 | 4715 | |
131dec34 SS |
4716 | /* Only USB 3.0 devices are connected to SuperSpeed hubs. */ |
4717 | if (hub_is_superspeed(hub->hdev)) | |
e7b77172 SS |
4718 | udev->speed = USB_SPEED_SUPER; |
4719 | else | |
4720 | udev->speed = USB_SPEED_UNKNOWN; | |
4721 | ||
3b29b68b | 4722 | choose_devnum(udev); |
c8d4af8e AX |
4723 | if (udev->devnum <= 0) { |
4724 | status = -ENOTCONN; /* Don't retry */ | |
4725 | goto loop; | |
c6515272 SS |
4726 | } |
4727 | ||
e7b77172 | 4728 | /* reset (non-USB 3.0 devices) and get descriptor */ |
5c79a1e3 | 4729 | usb_lock_port(port_dev); |
1da177e4 | 4730 | status = hub_port_init(hub, udev, port1, i); |
5c79a1e3 | 4731 | usb_unlock_port(port_dev); |
1da177e4 LT |
4732 | if (status < 0) |
4733 | goto loop; | |
4734 | ||
93362a87 PD |
4735 | if (udev->quirks & USB_QUIRK_DELAY_INIT) |
4736 | msleep(1000); | |
4737 | ||
1da177e4 LT |
4738 | /* consecutive bus-powered hubs aren't reliable; they can |
4739 | * violate the voltage drop budget. if the new child has | |
4740 | * a "powered" LED, users should notice we didn't enable it | |
4741 | * (without reading syslog), even without per-port LEDs | |
4742 | * on the parent. | |
4743 | */ | |
4744 | if (udev->descriptor.bDeviceClass == USB_CLASS_HUB | |
430ee58e | 4745 | && udev->bus_mA <= unit_load) { |
1da177e4 LT |
4746 | u16 devstat; |
4747 | ||
4748 | status = usb_get_status(udev, USB_RECIP_DEVICE, 0, | |
4749 | &devstat); | |
15b7336e | 4750 | if (status) { |
1da177e4 LT |
4751 | dev_dbg(&udev->dev, "get status %d ?\n", status); |
4752 | goto loop_disable; | |
4753 | } | |
1da177e4 LT |
4754 | if ((devstat & (1 << USB_DEVICE_SELF_POWERED)) == 0) { |
4755 | dev_err(&udev->dev, | |
4756 | "can't connect bus-powered hub " | |
4757 | "to this port\n"); | |
4758 | if (hub->has_indicators) { | |
4759 | hub->indicator[port1-1] = | |
4760 | INDICATOR_AMBER_BLINK; | |
22f6a0f0 SD |
4761 | queue_delayed_work( |
4762 | system_power_efficient_wq, | |
4763 | &hub->leds, 0); | |
1da177e4 LT |
4764 | } |
4765 | status = -ENOTCONN; /* Don't retry */ | |
4766 | goto loop_disable; | |
4767 | } | |
4768 | } | |
469271f8 | 4769 | |
1da177e4 LT |
4770 | /* check for devices running slower than they could */ |
4771 | if (le16_to_cpu(udev->descriptor.bcdUSB) >= 0x0200 | |
4772 | && udev->speed == USB_SPEED_FULL | |
4773 | && highspeed_hubs != 0) | |
039b3307 | 4774 | check_highspeed(hub, udev, port1); |
1da177e4 | 4775 | |
fa286188 | 4776 | /* Store the parent's children[] pointer. At this point |
1da177e4 LT |
4777 | * udev becomes globally accessible, although presumably |
4778 | * no one will look at it until hdev is unlocked. | |
4779 | */ | |
1da177e4 LT |
4780 | status = 0; |
4781 | ||
d8521afe DW |
4782 | mutex_lock(&usb_port_peer_mutex); |
4783 | ||
1da177e4 LT |
4784 | /* We mustn't add new devices if the parent hub has |
4785 | * been disconnected; we would race with the | |
4786 | * recursively_mark_NOTATTACHED() routine. | |
4787 | */ | |
4788 | spin_lock_irq(&device_state_lock); | |
4789 | if (hdev->state == USB_STATE_NOTATTACHED) | |
4790 | status = -ENOTCONN; | |
4791 | else | |
d99f6b41 | 4792 | port_dev->child = udev; |
1da177e4 | 4793 | spin_unlock_irq(&device_state_lock); |
d8521afe | 4794 | mutex_unlock(&usb_port_peer_mutex); |
1da177e4 LT |
4795 | |
4796 | /* Run it through the hoops (find a driver, etc) */ | |
4797 | if (!status) { | |
4798 | status = usb_new_device(udev); | |
4799 | if (status) { | |
d8521afe | 4800 | mutex_lock(&usb_port_peer_mutex); |
1da177e4 | 4801 | spin_lock_irq(&device_state_lock); |
d99f6b41 | 4802 | port_dev->child = NULL; |
1da177e4 | 4803 | spin_unlock_irq(&device_state_lock); |
d8521afe | 4804 | mutex_unlock(&usb_port_peer_mutex); |
01ed67dc TZ |
4805 | } else { |
4806 | if (hcd->usb_phy && !hdev->parent) | |
4807 | usb_phy_notify_connect(hcd->usb_phy, | |
4808 | udev->speed); | |
1da177e4 LT |
4809 | } |
4810 | } | |
4811 | ||
1da177e4 LT |
4812 | if (status) |
4813 | goto loop_disable; | |
4814 | ||
4815 | status = hub_power_remaining(hub); | |
4816 | if (status) | |
d99f6b41 | 4817 | dev_dbg(hub->intfdev, "%dmA power budget left\n", status); |
1da177e4 LT |
4818 | |
4819 | return; | |
4820 | ||
4821 | loop_disable: | |
4822 | hub_port_disable(hub, port1, 1); | |
4823 | loop: | |
fc721f51 | 4824 | usb_ep0_reinit(udev); |
3b29b68b | 4825 | release_devnum(udev); |
f7410ced | 4826 | hub_free_dev(udev); |
1da177e4 | 4827 | usb_put_dev(udev); |
ffcdc18d | 4828 | if ((status == -ENOTCONN) || (status == -ENOTSUPP)) |
1da177e4 LT |
4829 | break; |
4830 | } | |
3a31155c AS |
4831 | if (hub->hdev->parent || |
4832 | !hcd->driver->port_handed_over || | |
e9e88fb7 AS |
4833 | !(hcd->driver->port_handed_over)(hcd, port1)) { |
4834 | if (status != -ENOTCONN && status != -ENODEV) | |
d99f6b41 DW |
4835 | dev_err(&port_dev->dev, |
4836 | "unable to enumerate USB device\n"); | |
e9e88fb7 | 4837 | } |
469271f8 | 4838 | |
1da177e4 LT |
4839 | done: |
4840 | hub_port_disable(hub, port1, 1); | |
90da096e BR |
4841 | if (hcd->driver->relinquish_port && !hub->hdev->parent) |
4842 | hcd->driver->relinquish_port(hcd, port1); | |
af376a46 | 4843 | |
1da177e4 LT |
4844 | } |
4845 | ||
af376a46 DW |
4846 | /* Handle physical or logical connection change events. |
4847 | * This routine is called when: | |
4848 | * a port connection-change occurs; | |
4849 | * a port enable-change occurs (often caused by EMI); | |
4850 | * usb_reset_and_verify_device() encounters changed descriptors (as from | |
4851 | * a firmware download) | |
4852 | * caller already locked the hub | |
4853 | */ | |
4854 | static void hub_port_connect_change(struct usb_hub *hub, int port1, | |
4855 | u16 portstatus, u16 portchange) | |
5c79a1e3 | 4856 | __must_hold(&port_dev->status_lock) |
714b07be | 4857 | { |
af376a46 DW |
4858 | struct usb_port *port_dev = hub->ports[port1 - 1]; |
4859 | struct usb_device *udev = port_dev->child; | |
4860 | int status = -ENODEV; | |
714b07be | 4861 | |
af376a46 DW |
4862 | dev_dbg(&port_dev->dev, "status %04x, change %04x, %s\n", portstatus, |
4863 | portchange, portspeed(hub, portstatus)); | |
4864 | ||
4865 | if (hub->has_indicators) { | |
4866 | set_port_led(hub, port1, HUB_LED_AUTO); | |
4867 | hub->indicator[port1-1] = INDICATOR_AUTO; | |
4ee823b8 SS |
4868 | } |
4869 | ||
af376a46 DW |
4870 | #ifdef CONFIG_USB_OTG |
4871 | /* during HNP, don't repeat the debounce */ | |
4872 | if (hub->hdev->bus->is_b_host) | |
4873 | portchange &= ~(USB_PORT_STAT_C_CONNECTION | | |
4874 | USB_PORT_STAT_C_ENABLE); | |
4875 | #endif | |
4876 | ||
4877 | /* Try to resuscitate an existing device */ | |
4878 | if ((portstatus & USB_PORT_STAT_CONNECTION) && udev && | |
4879 | udev->state != USB_STATE_NOTATTACHED) { | |
4880 | if (portstatus & USB_PORT_STAT_ENABLE) { | |
4881 | status = 0; /* Nothing to do */ | |
ceb6c9c8 | 4882 | #ifdef CONFIG_PM |
af376a46 DW |
4883 | } else if (udev->state == USB_STATE_SUSPENDED && |
4884 | udev->persist_enabled) { | |
4885 | /* For a suspended device, treat this as a | |
4886 | * remote wakeup event. | |
4887 | */ | |
5c79a1e3 | 4888 | usb_unlock_port(port_dev); |
af376a46 | 4889 | status = usb_remote_wakeup(udev); |
5c79a1e3 | 4890 | usb_lock_port(port_dev); |
af376a46 DW |
4891 | #endif |
4892 | } else { | |
4893 | /* Don't resuscitate */; | |
4894 | } | |
af376a46 DW |
4895 | } |
4896 | clear_bit(port1, hub->change_bits); | |
4897 | ||
5c79a1e3 | 4898 | /* successfully revalidated the connection */ |
af376a46 DW |
4899 | if (status == 0) |
4900 | return; | |
4901 | ||
5c79a1e3 | 4902 | usb_unlock_port(port_dev); |
af376a46 | 4903 | hub_port_connect(hub, port1, portstatus, portchange); |
5c79a1e3 | 4904 | usb_lock_port(port_dev); |
1da177e4 LT |
4905 | } |
4906 | ||
af376a46 | 4907 | static void port_event(struct usb_hub *hub, int port1) |
5c79a1e3 | 4908 | __must_hold(&port_dev->status_lock) |
af376a46 | 4909 | { |
7671bd1e | 4910 | int connect_change; |
af376a46 DW |
4911 | struct usb_port *port_dev = hub->ports[port1 - 1]; |
4912 | struct usb_device *udev = port_dev->child; | |
4913 | struct usb_device *hdev = hub->hdev; | |
4914 | u16 portstatus, portchange; | |
4915 | ||
4916 | connect_change = test_bit(port1, hub->change_bits); | |
4917 | clear_bit(port1, hub->event_bits); | |
4918 | clear_bit(port1, hub->wakeup_bits); | |
4919 | ||
4920 | if (hub_port_status(hub, port1, &portstatus, &portchange) < 0) | |
4921 | return; | |
4922 | ||
4923 | if (portchange & USB_PORT_STAT_C_CONNECTION) { | |
4924 | usb_clear_port_feature(hdev, port1, USB_PORT_FEAT_C_CONNECTION); | |
4925 | connect_change = 1; | |
4926 | } | |
4927 | ||
4928 | if (portchange & USB_PORT_STAT_C_ENABLE) { | |
4929 | if (!connect_change) | |
4930 | dev_dbg(&port_dev->dev, "enable change, status %08x\n", | |
4931 | portstatus); | |
4932 | usb_clear_port_feature(hdev, port1, USB_PORT_FEAT_C_ENABLE); | |
4933 | ||
4934 | /* | |
4935 | * EM interference sometimes causes badly shielded USB devices | |
4936 | * to be shutdown by the hub, this hack enables them again. | |
4937 | * Works at least with mouse driver. | |
4938 | */ | |
4939 | if (!(portstatus & USB_PORT_STAT_ENABLE) | |
4940 | && !connect_change && udev) { | |
4941 | dev_err(&port_dev->dev, "disabled by hub (EMI?), re-enabling...\n"); | |
4942 | connect_change = 1; | |
4943 | } | |
4944 | } | |
4945 | ||
4946 | if (portchange & USB_PORT_STAT_C_OVERCURRENT) { | |
4947 | u16 status = 0, unused; | |
4948 | ||
4949 | dev_dbg(&port_dev->dev, "over-current change\n"); | |
4950 | usb_clear_port_feature(hdev, port1, | |
4951 | USB_PORT_FEAT_C_OVER_CURRENT); | |
4952 | msleep(100); /* Cool down */ | |
4953 | hub_power_on(hub, true); | |
4954 | hub_port_status(hub, port1, &status, &unused); | |
4955 | if (status & USB_PORT_STAT_OVERCURRENT) | |
4956 | dev_err(&port_dev->dev, "over-current condition\n"); | |
4957 | } | |
4958 | ||
4959 | if (portchange & USB_PORT_STAT_C_RESET) { | |
4960 | dev_dbg(&port_dev->dev, "reset change\n"); | |
4961 | usb_clear_port_feature(hdev, port1, USB_PORT_FEAT_C_RESET); | |
4962 | } | |
4963 | if ((portchange & USB_PORT_STAT_C_BH_RESET) | |
4964 | && hub_is_superspeed(hdev)) { | |
4965 | dev_dbg(&port_dev->dev, "warm reset change\n"); | |
4966 | usb_clear_port_feature(hdev, port1, | |
4967 | USB_PORT_FEAT_C_BH_PORT_RESET); | |
4968 | } | |
4969 | if (portchange & USB_PORT_STAT_C_LINK_STATE) { | |
4970 | dev_dbg(&port_dev->dev, "link state change\n"); | |
4971 | usb_clear_port_feature(hdev, port1, | |
4972 | USB_PORT_FEAT_C_PORT_LINK_STATE); | |
4973 | } | |
4974 | if (portchange & USB_PORT_STAT_C_CONFIG_ERROR) { | |
4975 | dev_warn(&port_dev->dev, "config error\n"); | |
4976 | usb_clear_port_feature(hdev, port1, | |
4977 | USB_PORT_FEAT_C_PORT_CONFIG_ERROR); | |
4978 | } | |
4979 | ||
097a155f DW |
4980 | /* skip port actions that require the port to be powered on */ |
4981 | if (!pm_runtime_active(&port_dev->dev)) | |
4982 | return; | |
714b07be | 4983 | |
af376a46 DW |
4984 | if (hub_handle_remote_wakeup(hub, port1, portstatus, portchange)) |
4985 | connect_change = 1; | |
4986 | ||
4987 | /* | |
4988 | * Warm reset a USB3 protocol port if it's in | |
4989 | * SS.Inactive state. | |
4990 | */ | |
3cd12f91 | 4991 | if (hub_port_warm_reset_required(hub, port1, portstatus)) { |
af376a46 DW |
4992 | dev_dbg(&port_dev->dev, "do warm reset\n"); |
4993 | if (!udev || !(portstatus & USB_PORT_STAT_CONNECTION) | |
4994 | || udev->state == USB_STATE_NOTATTACHED) { | |
4995 | if (hub_port_reset(hub, port1, NULL, | |
4996 | HUB_BH_RESET_TIME, true) < 0) | |
4997 | hub_port_disable(hub, port1, 1); | |
7671bd1e ZJC |
4998 | } else { |
4999 | usb_unlock_port(port_dev); | |
5000 | usb_lock_device(udev); | |
5001 | usb_reset_device(udev); | |
5002 | usb_unlock_device(udev); | |
5003 | usb_lock_port(port_dev); | |
5004 | connect_change = 0; | |
5005 | } | |
714b07be | 5006 | } |
af376a46 DW |
5007 | |
5008 | if (connect_change) | |
5009 | hub_port_connect_change(hub, port1, portstatus, portchange); | |
714b07be SS |
5010 | } |
5011 | ||
32a69589 | 5012 | static void hub_event(struct work_struct *work) |
1da177e4 | 5013 | { |
1da177e4 LT |
5014 | struct usb_device *hdev; |
5015 | struct usb_interface *intf; | |
5016 | struct usb_hub *hub; | |
5017 | struct device *hub_dev; | |
5018 | u16 hubstatus; | |
5019 | u16 hubchange; | |
1da177e4 | 5020 | int i, ret; |
1da177e4 | 5021 | |
32a69589 | 5022 | hub = container_of(work, struct usb_hub, events); |
eb6e2924 PM |
5023 | hdev = hub->hdev; |
5024 | hub_dev = hub->intfdev; | |
5025 | intf = to_usb_interface(hub_dev); | |
32a69589 | 5026 | |
eb6e2924 PM |
5027 | dev_dbg(hub_dev, "state %d ports %d chg %04x evt %04x\n", |
5028 | hdev->state, hdev->maxchild, | |
5029 | /* NOTE: expects max 15 ports... */ | |
5030 | (u16) hub->change_bits[0], | |
5031 | (u16) hub->event_bits[0]); | |
5032 | ||
5033 | /* Lock the device, then check to see if we were | |
5034 | * disconnected while waiting for the lock to succeed. */ | |
5035 | usb_lock_device(hdev); | |
5036 | if (unlikely(hub->disconnected)) | |
32a69589 | 5037 | goto out_hdev_lock; |
eb6e2924 PM |
5038 | |
5039 | /* If the hub has died, clean up after it */ | |
5040 | if (hdev->state == USB_STATE_NOTATTACHED) { | |
5041 | hub->error = -ENODEV; | |
5042 | hub_quiesce(hub, HUB_DISCONNECT); | |
32a69589 | 5043 | goto out_hdev_lock; |
eb6e2924 PM |
5044 | } |
5045 | ||
5046 | /* Autoresume */ | |
5047 | ret = usb_autopm_get_interface(intf); | |
5048 | if (ret) { | |
5049 | dev_dbg(hub_dev, "Can't autoresume: %d\n", ret); | |
32a69589 | 5050 | goto out_hdev_lock; |
eb6e2924 | 5051 | } |
1da177e4 | 5052 | |
eb6e2924 PM |
5053 | /* If this is an inactive hub, do nothing */ |
5054 | if (hub->quiescing) | |
5055 | goto out_autopm; | |
1da177e4 | 5056 | |
eb6e2924 PM |
5057 | if (hub->error) { |
5058 | dev_dbg(hub_dev, "resetting for error %d\n", hub->error); | |
5059 | ||
5060 | ret = usb_reset_device(hdev); | |
40f122f3 | 5061 | if (ret) { |
eb6e2924 PM |
5062 | dev_dbg(hub_dev, "error resetting hub: %d\n", ret); |
5063 | goto out_autopm; | |
40f122f3 | 5064 | } |
a8e7c565 | 5065 | |
eb6e2924 PM |
5066 | hub->nerrors = 0; |
5067 | hub->error = 0; | |
5068 | } | |
1da177e4 | 5069 | |
eb6e2924 PM |
5070 | /* deal with port status changes */ |
5071 | for (i = 1; i <= hdev->maxchild; i++) { | |
5072 | struct usb_port *port_dev = hub->ports[i - 1]; | |
1da177e4 | 5073 | |
eb6e2924 PM |
5074 | if (test_bit(i, hub->event_bits) |
5075 | || test_bit(i, hub->change_bits) | |
5076 | || test_bit(i, hub->wakeup_bits)) { | |
5077 | /* | |
5078 | * The get_noresume and barrier ensure that if | |
5079 | * the port was in the process of resuming, we | |
5080 | * flush that work and keep the port active for | |
5081 | * the duration of the port_event(). However, | |
5082 | * if the port is runtime pm suspended | |
5083 | * (powered-off), we leave it in that state, run | |
5084 | * an abbreviated port_event(), and move on. | |
5085 | */ | |
5086 | pm_runtime_get_noresume(&port_dev->dev); | |
5087 | pm_runtime_barrier(&port_dev->dev); | |
5088 | usb_lock_port(port_dev); | |
5089 | port_event(hub, i); | |
5090 | usb_unlock_port(port_dev); | |
5091 | pm_runtime_put_sync(&port_dev->dev); | |
1da177e4 | 5092 | } |
eb6e2924 | 5093 | } |
1da177e4 | 5094 | |
eb6e2924 PM |
5095 | /* deal with hub status changes */ |
5096 | if (test_and_clear_bit(0, hub->event_bits) == 0) | |
5097 | ; /* do nothing */ | |
5098 | else if (hub_hub_status(hub, &hubstatus, &hubchange) < 0) | |
5099 | dev_err(hub_dev, "get_hub_status failed\n"); | |
5100 | else { | |
5101 | if (hubchange & HUB_CHANGE_LOCAL_POWER) { | |
5102 | dev_dbg(hub_dev, "power change\n"); | |
5103 | clear_hub_feature(hdev, C_HUB_LOCAL_POWER); | |
5104 | if (hubstatus & HUB_STATUS_LOCAL_POWER) | |
5105 | /* FIXME: Is this always true? */ | |
5106 | hub->limited_power = 1; | |
5107 | else | |
5108 | hub->limited_power = 0; | |
af376a46 | 5109 | } |
eb6e2924 PM |
5110 | if (hubchange & HUB_CHANGE_OVERCURRENT) { |
5111 | u16 status = 0; | |
5112 | u16 unused; | |
1da177e4 | 5113 | |
eb6e2924 PM |
5114 | dev_dbg(hub_dev, "over-current change\n"); |
5115 | clear_hub_feature(hdev, C_HUB_OVER_CURRENT); | |
5116 | msleep(500); /* Cool down */ | |
5117 | hub_power_on(hub, true); | |
5118 | hub_hub_status(hub, &status, &unused); | |
5119 | if (status & HUB_STATUS_OVERCURRENT) | |
5120 | dev_err(hub_dev, "over-current condition\n"); | |
1da177e4 | 5121 | } |
eb6e2924 | 5122 | } |
1da177e4 | 5123 | |
eb6e2924 PM |
5124 | out_autopm: |
5125 | /* Balance the usb_autopm_get_interface() above */ | |
5126 | usb_autopm_put_interface_no_suspend(intf); | |
32a69589 | 5127 | out_hdev_lock: |
eb6e2924 | 5128 | usb_unlock_device(hdev); |
1da177e4 | 5129 | |
32a69589 PM |
5130 | /* Balance the stuff in kick_hub_wq() and allow autosuspend */ |
5131 | usb_autopm_put_interface(intf); | |
5132 | kref_put(&hub->kref, hub_release); | |
1da177e4 LT |
5133 | } |
5134 | ||
1e927d96 | 5135 | static const struct usb_device_id hub_id_table[] = { |
e6f30dea | 5136 | { .match_flags = USB_DEVICE_ID_MATCH_VENDOR |
469271f8 | 5137 | | USB_DEVICE_ID_MATCH_INT_CLASS, |
e6f30dea ML |
5138 | .idVendor = USB_VENDOR_GENESYS_LOGIC, |
5139 | .bInterfaceClass = USB_CLASS_HUB, | |
5140 | .driver_info = HUB_QUIRK_CHECK_PORT_AUTOSUSPEND}, | |
1da177e4 LT |
5141 | { .match_flags = USB_DEVICE_ID_MATCH_DEV_CLASS, |
5142 | .bDeviceClass = USB_CLASS_HUB}, | |
5143 | { .match_flags = USB_DEVICE_ID_MATCH_INT_CLASS, | |
5144 | .bInterfaceClass = USB_CLASS_HUB}, | |
5145 | { } /* Terminating entry */ | |
5146 | }; | |
5147 | ||
039b3307 | 5148 | MODULE_DEVICE_TABLE(usb, hub_id_table); |
1da177e4 LT |
5149 | |
5150 | static struct usb_driver hub_driver = { | |
1da177e4 LT |
5151 | .name = "hub", |
5152 | .probe = hub_probe, | |
5153 | .disconnect = hub_disconnect, | |
5154 | .suspend = hub_suspend, | |
5155 | .resume = hub_resume, | |
f07600cf | 5156 | .reset_resume = hub_reset_resume, |
7de18d8b AS |
5157 | .pre_reset = hub_pre_reset, |
5158 | .post_reset = hub_post_reset, | |
c532b29a | 5159 | .unlocked_ioctl = hub_ioctl, |
1da177e4 | 5160 | .id_table = hub_id_table, |
40f122f3 | 5161 | .supports_autosuspend = 1, |
1da177e4 LT |
5162 | }; |
5163 | ||
5164 | int usb_hub_init(void) | |
5165 | { | |
1da177e4 LT |
5166 | if (usb_register(&hub_driver) < 0) { |
5167 | printk(KERN_ERR "%s: can't register hub driver\n", | |
5168 | usbcore_name); | |
5169 | return -1; | |
5170 | } | |
5171 | ||
32a69589 PM |
5172 | /* |
5173 | * The workqueue needs to be freezable to avoid interfering with | |
5174 | * USB-PERSIST port handover. Otherwise it might see that a full-speed | |
5175 | * device was gone before the EHCI controller had handed its port | |
5176 | * over to the companion full-speed controller. | |
32a69589 | 5177 | */ |
638139eb | 5178 | hub_wq = alloc_workqueue("usb_hub_wq", WQ_FREEZABLE, 0); |
32a69589 | 5179 | if (hub_wq) |
1da177e4 | 5180 | return 0; |
1da177e4 LT |
5181 | |
5182 | /* Fall through if kernel_thread failed */ | |
5183 | usb_deregister(&hub_driver); | |
32a69589 | 5184 | pr_err("%s: can't allocate workqueue for usb hub\n", usbcore_name); |
1da177e4 LT |
5185 | |
5186 | return -1; | |
5187 | } | |
5188 | ||
5189 | void usb_hub_cleanup(void) | |
5190 | { | |
32a69589 | 5191 | destroy_workqueue(hub_wq); |
1da177e4 LT |
5192 | |
5193 | /* | |
5194 | * Hub resources are freed for us by usb_deregister. It calls | |
5195 | * usb_driver_purge on every device which in turn calls that | |
5196 | * devices disconnect function if it is using this driver. | |
5197 | * The hub_disconnect function takes care of releasing the | |
5198 | * individual hub resources. -greg | |
5199 | */ | |
5200 | usb_deregister(&hub_driver); | |
5201 | } /* usb_hub_cleanup() */ | |
5202 | ||
eb764c4b | 5203 | static int descriptors_changed(struct usb_device *udev, |
e3376d6c XR |
5204 | struct usb_device_descriptor *old_device_descriptor, |
5205 | struct usb_host_bos *old_bos) | |
eb764c4b AS |
5206 | { |
5207 | int changed = 0; | |
5208 | unsigned index; | |
5209 | unsigned serial_len = 0; | |
5210 | unsigned len; | |
5211 | unsigned old_length; | |
5212 | int length; | |
5213 | char *buf; | |
5214 | ||
5215 | if (memcmp(&udev->descriptor, old_device_descriptor, | |
5216 | sizeof(*old_device_descriptor)) != 0) | |
5217 | return 1; | |
5218 | ||
e3376d6c XR |
5219 | if ((old_bos && !udev->bos) || (!old_bos && udev->bos)) |
5220 | return 1; | |
5221 | if (udev->bos) { | |
b9a10481 XR |
5222 | len = le16_to_cpu(udev->bos->desc->wTotalLength); |
5223 | if (len != le16_to_cpu(old_bos->desc->wTotalLength)) | |
e3376d6c | 5224 | return 1; |
b9a10481 | 5225 | if (memcmp(udev->bos->desc, old_bos->desc, len)) |
e3376d6c XR |
5226 | return 1; |
5227 | } | |
5228 | ||
eb764c4b AS |
5229 | /* Since the idVendor, idProduct, and bcdDevice values in the |
5230 | * device descriptor haven't changed, we will assume the | |
5231 | * Manufacturer and Product strings haven't changed either. | |
5232 | * But the SerialNumber string could be different (e.g., a | |
5233 | * different flash card of the same brand). | |
5234 | */ | |
5235 | if (udev->serial) | |
5236 | serial_len = strlen(udev->serial) + 1; | |
1da177e4 | 5237 | |
eb764c4b | 5238 | len = serial_len; |
1da177e4 | 5239 | for (index = 0; index < udev->descriptor.bNumConfigurations; index++) { |
eb764c4b AS |
5240 | old_length = le16_to_cpu(udev->config[index].desc.wTotalLength); |
5241 | len = max(len, old_length); | |
1da177e4 | 5242 | } |
eb764c4b | 5243 | |
0cc1a51f | 5244 | buf = kmalloc(len, GFP_NOIO); |
1da177e4 LT |
5245 | if (buf == NULL) { |
5246 | dev_err(&udev->dev, "no mem to re-read configs after reset\n"); | |
5247 | /* assume the worst */ | |
5248 | return 1; | |
5249 | } | |
5250 | for (index = 0; index < udev->descriptor.bNumConfigurations; index++) { | |
eb764c4b | 5251 | old_length = le16_to_cpu(udev->config[index].desc.wTotalLength); |
1da177e4 LT |
5252 | length = usb_get_descriptor(udev, USB_DT_CONFIG, index, buf, |
5253 | old_length); | |
eb764c4b | 5254 | if (length != old_length) { |
1da177e4 LT |
5255 | dev_dbg(&udev->dev, "config index %d, error %d\n", |
5256 | index, length); | |
eb764c4b | 5257 | changed = 1; |
1da177e4 LT |
5258 | break; |
5259 | } | |
039b3307 | 5260 | if (memcmp(buf, udev->rawdescriptors[index], old_length) |
1da177e4 LT |
5261 | != 0) { |
5262 | dev_dbg(&udev->dev, "config index %d changed (#%d)\n", | |
eb764c4b AS |
5263 | index, |
5264 | ((struct usb_config_descriptor *) buf)-> | |
5265 | bConfigurationValue); | |
5266 | changed = 1; | |
1da177e4 LT |
5267 | break; |
5268 | } | |
5269 | } | |
eb764c4b AS |
5270 | |
5271 | if (!changed && serial_len) { | |
5272 | length = usb_string(udev, udev->descriptor.iSerialNumber, | |
5273 | buf, serial_len); | |
5274 | if (length + 1 != serial_len) { | |
5275 | dev_dbg(&udev->dev, "serial string error %d\n", | |
5276 | length); | |
5277 | changed = 1; | |
5278 | } else if (memcmp(buf, udev->serial, length) != 0) { | |
5279 | dev_dbg(&udev->dev, "serial string changed\n"); | |
5280 | changed = 1; | |
5281 | } | |
5282 | } | |
5283 | ||
1da177e4 | 5284 | kfree(buf); |
eb764c4b | 5285 | return changed; |
1da177e4 LT |
5286 | } |
5287 | ||
5288 | /** | |
742120c6 | 5289 | * usb_reset_and_verify_device - perform a USB port reset to reinitialize a device |
1da177e4 LT |
5290 | * @udev: device to reset (not in SUSPENDED or NOTATTACHED state) |
5291 | * | |
79efa097 AS |
5292 | * WARNING - don't use this routine to reset a composite device |
5293 | * (one with multiple interfaces owned by separate drivers)! | |
742120c6 | 5294 | * Use usb_reset_device() instead. |
1da177e4 LT |
5295 | * |
5296 | * Do a port reset, reassign the device's address, and establish its | |
5297 | * former operating configuration. If the reset fails, or the device's | |
5298 | * descriptors change from their values before the reset, or the original | |
5299 | * configuration and altsettings cannot be restored, a flag will be set | |
37ebb549 | 5300 | * telling hub_wq to pretend the device has been disconnected and then |
1da177e4 LT |
5301 | * re-connected. All drivers will be unbound, and the device will be |
5302 | * re-enumerated and probed all over again. | |
5303 | * | |
626f090c | 5304 | * Return: 0 if the reset succeeded, -ENODEV if the device has been |
1da177e4 LT |
5305 | * flagged for logical disconnection, or some other negative error code |
5306 | * if the reset wasn't even attempted. | |
5307 | * | |
626f090c | 5308 | * Note: |
5c79a1e3 DW |
5309 | * The caller must own the device lock and the port lock, the latter is |
5310 | * taken by usb_reset_device(). For example, it's safe to use | |
5311 | * usb_reset_device() from a driver probe() routine after downloading | |
5312 | * new firmware. For calls that might not occur during probe(), drivers | |
5313 | * should lock the device using usb_lock_device_for_reset(). | |
6bc6cff5 AS |
5314 | * |
5315 | * Locking exception: This routine may also be called from within an | |
5316 | * autoresume handler. Such usage won't conflict with other tasks | |
5317 | * holding the device lock because these tasks should always call | |
5c79a1e3 DW |
5318 | * usb_autopm_resume_device(), thereby preventing any unwanted |
5319 | * autoresume. The autoresume handler is expected to have already | |
5320 | * acquired the port lock before calling this routine. | |
1da177e4 | 5321 | */ |
742120c6 | 5322 | static int usb_reset_and_verify_device(struct usb_device *udev) |
1da177e4 LT |
5323 | { |
5324 | struct usb_device *parent_hdev = udev->parent; | |
5325 | struct usb_hub *parent_hub; | |
3f0479e0 | 5326 | struct usb_hcd *hcd = bus_to_hcd(udev->bus); |
1da177e4 | 5327 | struct usb_device_descriptor descriptor = udev->descriptor; |
e3376d6c | 5328 | struct usb_host_bos *bos; |
7a7b562d | 5329 | int i, j, ret = 0; |
12c3da34 | 5330 | int port1 = udev->portnum; |
1da177e4 LT |
5331 | |
5332 | if (udev->state == USB_STATE_NOTATTACHED || | |
5333 | udev->state == USB_STATE_SUSPENDED) { | |
5334 | dev_dbg(&udev->dev, "device reset not allowed in state %d\n", | |
5335 | udev->state); | |
5336 | return -EINVAL; | |
5337 | } | |
5338 | ||
5c79a1e3 | 5339 | if (!parent_hdev) |
1da177e4 | 5340 | return -EISDIR; |
5c79a1e3 | 5341 | |
ad493e5e | 5342 | parent_hub = usb_hub_to_struct_hub(parent_hdev); |
1da177e4 | 5343 | |
dcc01c08 SS |
5344 | /* Disable USB2 hardware LPM. |
5345 | * It will be re-enabled by the enumeration process. | |
5346 | */ | |
5347 | if (udev->usb2_hw_lpm_enabled == 1) | |
5348 | usb_set_usb2_hardware_lpm(udev, 0); | |
5349 | ||
f74631e3 SS |
5350 | /* Disable LPM and LTM while we reset the device and reinstall the alt |
5351 | * settings. Device-initiated LPM settings, and system exit latency | |
5352 | * settings are cleared when the device is reset, so we have to set | |
5353 | * them up again. | |
6d1d0513 SS |
5354 | */ |
5355 | ret = usb_unlocked_disable_lpm(udev); | |
5356 | if (ret) { | |
5357 | dev_err(&udev->dev, "%s Failed to disable LPM\n.", __func__); | |
464ad8c4 | 5358 | goto re_enumerate_no_bos; |
6d1d0513 | 5359 | } |
f74631e3 SS |
5360 | ret = usb_disable_ltm(udev); |
5361 | if (ret) { | |
5362 | dev_err(&udev->dev, "%s Failed to disable LTM\n.", | |
5363 | __func__); | |
464ad8c4 | 5364 | goto re_enumerate_no_bos; |
f74631e3 | 5365 | } |
6d1d0513 | 5366 | |
464ad8c4 HY |
5367 | bos = udev->bos; |
5368 | udev->bos = NULL; | |
5369 | ||
1da177e4 LT |
5370 | for (i = 0; i < SET_CONFIG_TRIES; ++i) { |
5371 | ||
5372 | /* ep0 maxpacket size may change; let the HCD know about it. | |
5373 | * Other endpoints will be handled by re-enumeration. */ | |
fc721f51 | 5374 | usb_ep0_reinit(udev); |
1da177e4 | 5375 | ret = hub_port_init(parent_hub, udev, port1, i); |
dd4dd19e | 5376 | if (ret >= 0 || ret == -ENOTCONN || ret == -ENODEV) |
1da177e4 LT |
5377 | break; |
5378 | } | |
d5cbad4b | 5379 | |
1da177e4 LT |
5380 | if (ret < 0) |
5381 | goto re_enumerate; | |
469271f8 | 5382 | |
1da177e4 | 5383 | /* Device might have changed firmware (DFU or similar) */ |
e3376d6c | 5384 | if (descriptors_changed(udev, &descriptor, bos)) { |
1da177e4 LT |
5385 | dev_info(&udev->dev, "device firmware changed\n"); |
5386 | udev->descriptor = descriptor; /* for disconnect() calls */ | |
5387 | goto re_enumerate; | |
469271f8 | 5388 | } |
4fe0387a AS |
5389 | |
5390 | /* Restore the device's previous configuration */ | |
1da177e4 LT |
5391 | if (!udev->actconfig) |
5392 | goto done; | |
3f0479e0 | 5393 | |
d673bfcb | 5394 | mutex_lock(hcd->bandwidth_mutex); |
3f0479e0 SS |
5395 | ret = usb_hcd_alloc_bandwidth(udev, udev->actconfig, NULL, NULL); |
5396 | if (ret < 0) { | |
5397 | dev_warn(&udev->dev, | |
5398 | "Busted HC? Not enough HCD resources for " | |
5399 | "old configuration.\n"); | |
d673bfcb | 5400 | mutex_unlock(hcd->bandwidth_mutex); |
3f0479e0 SS |
5401 | goto re_enumerate; |
5402 | } | |
1da177e4 LT |
5403 | ret = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), |
5404 | USB_REQ_SET_CONFIGURATION, 0, | |
5405 | udev->actconfig->desc.bConfigurationValue, 0, | |
5406 | NULL, 0, USB_CTRL_SET_TIMEOUT); | |
5407 | if (ret < 0) { | |
5408 | dev_err(&udev->dev, | |
5409 | "can't restore configuration #%d (error=%d)\n", | |
5410 | udev->actconfig->desc.bConfigurationValue, ret); | |
d673bfcb | 5411 | mutex_unlock(hcd->bandwidth_mutex); |
1da177e4 | 5412 | goto re_enumerate; |
469271f8 | 5413 | } |
d673bfcb | 5414 | mutex_unlock(hcd->bandwidth_mutex); |
1da177e4 LT |
5415 | usb_set_device_state(udev, USB_STATE_CONFIGURED); |
5416 | ||
4fe0387a AS |
5417 | /* Put interfaces back into the same altsettings as before. |
5418 | * Don't bother to send the Set-Interface request for interfaces | |
5419 | * that were already in altsetting 0; besides being unnecessary, | |
5420 | * many devices can't handle it. Instead just reset the host-side | |
5421 | * endpoint state. | |
5422 | */ | |
1da177e4 | 5423 | for (i = 0; i < udev->actconfig->desc.bNumInterfaces; i++) { |
3f0479e0 SS |
5424 | struct usb_host_config *config = udev->actconfig; |
5425 | struct usb_interface *intf = config->interface[i]; | |
1da177e4 LT |
5426 | struct usb_interface_descriptor *desc; |
5427 | ||
1da177e4 | 5428 | desc = &intf->cur_altsetting->desc; |
4fe0387a AS |
5429 | if (desc->bAlternateSetting == 0) { |
5430 | usb_disable_interface(udev, intf, true); | |
5431 | usb_enable_interface(udev, intf, true); | |
5432 | ret = 0; | |
5433 | } else { | |
04a723ea SS |
5434 | /* Let the bandwidth allocation function know that this |
5435 | * device has been reset, and it will have to use | |
5436 | * alternate setting 0 as the current alternate setting. | |
3f0479e0 | 5437 | */ |
04a723ea | 5438 | intf->resetting_device = 1; |
4fe0387a AS |
5439 | ret = usb_set_interface(udev, desc->bInterfaceNumber, |
5440 | desc->bAlternateSetting); | |
04a723ea | 5441 | intf->resetting_device = 0; |
4fe0387a | 5442 | } |
1da177e4 LT |
5443 | if (ret < 0) { |
5444 | dev_err(&udev->dev, "failed to restore interface %d " | |
5445 | "altsetting %d (error=%d)\n", | |
5446 | desc->bInterfaceNumber, | |
5447 | desc->bAlternateSetting, | |
5448 | ret); | |
5449 | goto re_enumerate; | |
5450 | } | |
7a7b562d HG |
5451 | /* Resetting also frees any allocated streams */ |
5452 | for (j = 0; j < intf->cur_altsetting->desc.bNumEndpoints; j++) | |
5453 | intf->cur_altsetting->endpoint[j].streams = 0; | |
1da177e4 LT |
5454 | } |
5455 | ||
5456 | done: | |
f74631e3 | 5457 | /* Now that the alt settings are re-installed, enable LTM and LPM. */ |
de68bab4 | 5458 | usb_set_usb2_hardware_lpm(udev, 1); |
8306095f | 5459 | usb_unlocked_enable_lpm(udev); |
f74631e3 | 5460 | usb_enable_ltm(udev); |
e3376d6c XR |
5461 | usb_release_bos_descriptor(udev); |
5462 | udev->bos = bos; | |
1da177e4 | 5463 | return 0; |
469271f8 | 5464 | |
1da177e4 | 5465 | re_enumerate: |
e3376d6c XR |
5466 | usb_release_bos_descriptor(udev); |
5467 | udev->bos = bos; | |
464ad8c4 HY |
5468 | re_enumerate_no_bos: |
5469 | /* LPM state doesn't matter when we're about to destroy the device. */ | |
5470 | hub_port_logical_disconnect(parent_hub, port1); | |
1da177e4 LT |
5471 | return -ENODEV; |
5472 | } | |
79efa097 AS |
5473 | |
5474 | /** | |
742120c6 | 5475 | * usb_reset_device - warn interface drivers and perform a USB port reset |
79efa097 | 5476 | * @udev: device to reset (not in SUSPENDED or NOTATTACHED state) |
79efa097 AS |
5477 | * |
5478 | * Warns all drivers bound to registered interfaces (using their pre_reset | |
5479 | * method), performs the port reset, and then lets the drivers know that | |
5480 | * the reset is over (using their post_reset method). | |
5481 | * | |
626f090c | 5482 | * Return: The same as for usb_reset_and_verify_device(). |
79efa097 | 5483 | * |
626f090c | 5484 | * Note: |
79efa097 AS |
5485 | * The caller must own the device lock. For example, it's safe to use |
5486 | * this from a driver probe() routine after downloading new firmware. | |
5487 | * For calls that might not occur during probe(), drivers should lock | |
5488 | * the device using usb_lock_device_for_reset(). | |
78d9a487 AS |
5489 | * |
5490 | * If an interface is currently being probed or disconnected, we assume | |
5491 | * its driver knows how to handle resets. For all other interfaces, | |
5492 | * if the driver doesn't have pre_reset and post_reset methods then | |
5493 | * we attempt to unbind it and rebind afterward. | |
79efa097 | 5494 | */ |
742120c6 | 5495 | int usb_reset_device(struct usb_device *udev) |
79efa097 AS |
5496 | { |
5497 | int ret; | |
852c4b43 | 5498 | int i; |
4d769def | 5499 | unsigned int noio_flag; |
5c79a1e3 | 5500 | struct usb_port *port_dev; |
79efa097 | 5501 | struct usb_host_config *config = udev->actconfig; |
5c79a1e3 | 5502 | struct usb_hub *hub = usb_hub_to_struct_hub(udev->parent); |
79efa097 AS |
5503 | |
5504 | if (udev->state == USB_STATE_NOTATTACHED || | |
5505 | udev->state == USB_STATE_SUSPENDED) { | |
5506 | dev_dbg(&udev->dev, "device reset not allowed in state %d\n", | |
5507 | udev->state); | |
5508 | return -EINVAL; | |
5509 | } | |
5510 | ||
5c79a1e3 DW |
5511 | if (!udev->parent) { |
5512 | /* this requires hcd-specific logic; see ohci_restart() */ | |
5513 | dev_dbg(&udev->dev, "%s for root hub!\n", __func__); | |
5514 | return -EISDIR; | |
5515 | } | |
5516 | ||
5517 | port_dev = hub->ports[udev->portnum - 1]; | |
5518 | ||
4d769def ML |
5519 | /* |
5520 | * Don't allocate memory with GFP_KERNEL in current | |
5521 | * context to avoid possible deadlock if usb mass | |
5522 | * storage interface or usbnet interface(iSCSI case) | |
5523 | * is included in current configuration. The easist | |
5524 | * approach is to do it for every device reset, | |
5525 | * because the device 'memalloc_noio' flag may have | |
5526 | * not been set before reseting the usb device. | |
5527 | */ | |
5528 | noio_flag = memalloc_noio_save(); | |
5529 | ||
645daaab | 5530 | /* Prevent autosuspend during the reset */ |
94fcda1f | 5531 | usb_autoresume_device(udev); |
645daaab | 5532 | |
79efa097 | 5533 | if (config) { |
79efa097 | 5534 | for (i = 0; i < config->desc.bNumInterfaces; ++i) { |
852c4b43 AS |
5535 | struct usb_interface *cintf = config->interface[i]; |
5536 | struct usb_driver *drv; | |
78d9a487 | 5537 | int unbind = 0; |
852c4b43 AS |
5538 | |
5539 | if (cintf->dev.driver) { | |
79efa097 | 5540 | drv = to_usb_driver(cintf->dev.driver); |
78d9a487 AS |
5541 | if (drv->pre_reset && drv->post_reset) |
5542 | unbind = (drv->pre_reset)(cintf); | |
5543 | else if (cintf->condition == | |
5544 | USB_INTERFACE_BOUND) | |
5545 | unbind = 1; | |
5546 | if (unbind) | |
5547 | usb_forced_unbind_intf(cintf); | |
79efa097 AS |
5548 | } |
5549 | } | |
5550 | } | |
5551 | ||
5c79a1e3 | 5552 | usb_lock_port(port_dev); |
742120c6 | 5553 | ret = usb_reset_and_verify_device(udev); |
5c79a1e3 | 5554 | usb_unlock_port(port_dev); |
79efa097 AS |
5555 | |
5556 | if (config) { | |
79efa097 | 5557 | for (i = config->desc.bNumInterfaces - 1; i >= 0; --i) { |
852c4b43 AS |
5558 | struct usb_interface *cintf = config->interface[i]; |
5559 | struct usb_driver *drv; | |
78d9a487 | 5560 | int rebind = cintf->needs_binding; |
852c4b43 | 5561 | |
78d9a487 | 5562 | if (!rebind && cintf->dev.driver) { |
79efa097 AS |
5563 | drv = to_usb_driver(cintf->dev.driver); |
5564 | if (drv->post_reset) | |
78d9a487 AS |
5565 | rebind = (drv->post_reset)(cintf); |
5566 | else if (cintf->condition == | |
5567 | USB_INTERFACE_BOUND) | |
5568 | rebind = 1; | |
6aec044c AS |
5569 | if (rebind) |
5570 | cintf->needs_binding = 1; | |
79efa097 | 5571 | } |
79efa097 | 5572 | } |
6aec044c | 5573 | usb_unbind_and_rebind_marked_interfaces(udev); |
79efa097 AS |
5574 | } |
5575 | ||
94fcda1f | 5576 | usb_autosuspend_device(udev); |
4d769def | 5577 | memalloc_noio_restore(noio_flag); |
79efa097 AS |
5578 | return ret; |
5579 | } | |
742120c6 | 5580 | EXPORT_SYMBOL_GPL(usb_reset_device); |
dc023dce IPG |
5581 | |
5582 | ||
5583 | /** | |
5584 | * usb_queue_reset_device - Reset a USB device from an atomic context | |
5585 | * @iface: USB interface belonging to the device to reset | |
5586 | * | |
5587 | * This function can be used to reset a USB device from an atomic | |
5588 | * context, where usb_reset_device() won't work (as it blocks). | |
5589 | * | |
5590 | * Doing a reset via this method is functionally equivalent to calling | |
5591 | * usb_reset_device(), except for the fact that it is delayed to a | |
5592 | * workqueue. This means that any drivers bound to other interfaces | |
5593 | * might be unbound, as well as users from usbfs in user space. | |
5594 | * | |
5595 | * Corner cases: | |
5596 | * | |
5597 | * - Scheduling two resets at the same time from two different drivers | |
5598 | * attached to two different interfaces of the same device is | |
5599 | * possible; depending on how the driver attached to each interface | |
5600 | * handles ->pre_reset(), the second reset might happen or not. | |
5601 | * | |
524134d4 AS |
5602 | * - If the reset is delayed so long that the interface is unbound from |
5603 | * its driver, the reset will be skipped. | |
dc023dce | 5604 | * |
524134d4 AS |
5605 | * - This function can be called during .probe(). It can also be called |
5606 | * during .disconnect(), but doing so is pointless because the reset | |
5607 | * will not occur. If you really want to reset the device during | |
5608 | * .disconnect(), call usb_reset_device() directly -- but watch out | |
5609 | * for nested unbinding issues! | |
dc023dce IPG |
5610 | */ |
5611 | void usb_queue_reset_device(struct usb_interface *iface) | |
5612 | { | |
524134d4 AS |
5613 | if (schedule_work(&iface->reset_ws)) |
5614 | usb_get_intf(iface); | |
dc023dce IPG |
5615 | } |
5616 | EXPORT_SYMBOL_GPL(usb_queue_reset_device); | |
ff823c79 LT |
5617 | |
5618 | /** | |
5619 | * usb_hub_find_child - Get the pointer of child device | |
5620 | * attached to the port which is specified by @port1. | |
5621 | * @hdev: USB device belonging to the usb hub | |
5622 | * @port1: port num to indicate which port the child device | |
5623 | * is attached to. | |
5624 | * | |
5625 | * USB drivers call this function to get hub's child device | |
5626 | * pointer. | |
5627 | * | |
626f090c | 5628 | * Return: %NULL if input param is invalid and |
ff823c79 LT |
5629 | * child's usb_device pointer if non-NULL. |
5630 | */ | |
5631 | struct usb_device *usb_hub_find_child(struct usb_device *hdev, | |
5632 | int port1) | |
5633 | { | |
ad493e5e | 5634 | struct usb_hub *hub = usb_hub_to_struct_hub(hdev); |
ff823c79 LT |
5635 | |
5636 | if (port1 < 1 || port1 > hdev->maxchild) | |
5637 | return NULL; | |
5638 | return hub->ports[port1 - 1]->child; | |
5639 | } | |
5640 | EXPORT_SYMBOL_GPL(usb_hub_find_child); | |
d5575424 | 5641 | |
d2123fd9 LT |
5642 | void usb_hub_adjust_deviceremovable(struct usb_device *hdev, |
5643 | struct usb_hub_descriptor *desc) | |
5644 | { | |
d99f6b41 | 5645 | struct usb_hub *hub = usb_hub_to_struct_hub(hdev); |
d2123fd9 LT |
5646 | enum usb_port_connect_type connect_type; |
5647 | int i; | |
5648 | ||
d99f6b41 DW |
5649 | if (!hub) |
5650 | return; | |
5651 | ||
d2123fd9 LT |
5652 | if (!hub_is_superspeed(hdev)) { |
5653 | for (i = 1; i <= hdev->maxchild; i++) { | |
d99f6b41 | 5654 | struct usb_port *port_dev = hub->ports[i - 1]; |
d2123fd9 | 5655 | |
d99f6b41 | 5656 | connect_type = port_dev->connect_type; |
d2123fd9 LT |
5657 | if (connect_type == USB_PORT_CONNECT_TYPE_HARD_WIRED) { |
5658 | u8 mask = 1 << (i%8); | |
5659 | ||
5660 | if (!(desc->u.hs.DeviceRemovable[i/8] & mask)) { | |
d99f6b41 | 5661 | dev_dbg(&port_dev->dev, "DeviceRemovable is changed to 1 according to platform information.\n"); |
d2123fd9 LT |
5662 | desc->u.hs.DeviceRemovable[i/8] |= mask; |
5663 | } | |
5664 | } | |
5665 | } | |
5666 | } else { | |
5667 | u16 port_removable = le16_to_cpu(desc->u.ss.DeviceRemovable); | |
5668 | ||
5669 | for (i = 1; i <= hdev->maxchild; i++) { | |
d99f6b41 | 5670 | struct usb_port *port_dev = hub->ports[i - 1]; |
d2123fd9 | 5671 | |
d99f6b41 | 5672 | connect_type = port_dev->connect_type; |
d2123fd9 LT |
5673 | if (connect_type == USB_PORT_CONNECT_TYPE_HARD_WIRED) { |
5674 | u16 mask = 1 << i; | |
5675 | ||
5676 | if (!(port_removable & mask)) { | |
d99f6b41 | 5677 | dev_dbg(&port_dev->dev, "DeviceRemovable is changed to 1 according to platform information.\n"); |
d2123fd9 LT |
5678 | port_removable |= mask; |
5679 | } | |
5680 | } | |
5681 | } | |
5682 | ||
5683 | desc->u.ss.DeviceRemovable = cpu_to_le16(port_removable); | |
5684 | } | |
5685 | } | |
5686 | ||
d5575424 LT |
5687 | #ifdef CONFIG_ACPI |
5688 | /** | |
5689 | * usb_get_hub_port_acpi_handle - Get the usb port's acpi handle | |
5690 | * @hdev: USB device belonging to the usb hub | |
5691 | * @port1: port num of the port | |
5692 | * | |
626f090c YB |
5693 | * Return: Port's acpi handle if successful, %NULL if params are |
5694 | * invalid. | |
d5575424 LT |
5695 | */ |
5696 | acpi_handle usb_get_hub_port_acpi_handle(struct usb_device *hdev, | |
5697 | int port1) | |
5698 | { | |
ad493e5e | 5699 | struct usb_hub *hub = usb_hub_to_struct_hub(hdev); |
d5575424 | 5700 | |
41341261 MN |
5701 | if (!hub) |
5702 | return NULL; | |
5703 | ||
3a83f992 | 5704 | return ACPI_HANDLE(&hub->ports[port1 - 1]->dev); |
d5575424 LT |
5705 | } |
5706 | #endif |