]>
Commit | Line | Data |
---|---|---|
1da177e4 LT |
1 | # |
2 | # USB Gadget support on a system involves | |
3 | # (a) a peripheral controller, and | |
4 | # (b) the gadget driver using it. | |
5 | # | |
6 | # NOTE: Gadget support ** DOES NOT ** depend on host-side CONFIG_USB !! | |
7 | # | |
8 | # - Host systems (like PCs) need CONFIG_USB (with "A" jacks). | |
9 | # - Peripherals (like PDAs) need CONFIG_USB_GADGET (with "B" jacks). | |
cab00891 | 10 | # - Some systems have both kinds of controllers. |
1da177e4 LT |
11 | # |
12 | # With help from a special transceiver and a "Mini-AB" jack, systems with | |
13 | # both kinds of controller can also support "USB On-the-Go" (CONFIG_USB_OTG). | |
14 | # | |
1da177e4 | 15 | |
b75be4ab DC |
16 | menuconfig USB_GADGET |
17 | tristate "USB Gadget Support" | |
1da177e4 LT |
18 | help |
19 | USB is a master/slave protocol, organized with one master | |
20 | host (such as a PC) controlling up to 127 peripheral devices. | |
21 | The USB hardware is asymmetric, which makes it easier to set up: | |
22 | you can't connect a "to-the-host" connector to a peripheral. | |
23 | ||
24 | Linux can run in the host, or in the peripheral. In both cases | |
25 | you need a low level bus controller driver, and some software | |
26 | talking to it. Peripheral controllers are often discrete silicon, | |
27 | or are integrated with the CPU in a microcontroller. The more | |
e113f29c | 28 | familiar host side controllers have names like "EHCI", "OHCI", |
1da177e4 LT |
29 | or "UHCI", and are usually integrated into southbridges on PC |
30 | motherboards. | |
31 | ||
32 | Enable this configuration option if you want to run Linux inside | |
33 | a USB peripheral device. Configure one hardware driver for your | |
34 | peripheral/device side bus controller, and a "gadget driver" for | |
35 | your peripheral protocol. (If you use modular gadget drivers, | |
36 | you may configure more than one.) | |
37 | ||
38 | If in doubt, say "N" and don't enable these drivers; most people | |
39 | don't have this kind of hardware (except maybe inside Linux PDAs). | |
40 | ||
41 | For more information, see <http://www.linux-usb.org/gadget> and | |
42 | the kernel DocBook documentation for this API. | |
43 | ||
b75be4ab DC |
44 | if USB_GADGET |
45 | ||
70790f63 DB |
46 | config USB_GADGET_DEBUG |
47 | boolean "Debugging messages" | |
48 | depends on USB_GADGET && DEBUG_KERNEL && EXPERIMENTAL | |
49 | help | |
50 | Many controller and gadget drivers will print some debugging | |
51 | messages if you use this option to ask for those messages. | |
52 | ||
53 | Avoid enabling these messages, even if you're actively | |
54 | debugging such a driver. Many drivers will emit so many | |
55 | messages that the driver timings are affected, which will | |
56 | either create new failure modes or remove the one you're | |
57 | trying to track down. Never enable these messages for a | |
58 | production build. | |
59 | ||
1da177e4 LT |
60 | config USB_GADGET_DEBUG_FILES |
61 | boolean "Debugging information files" | |
62 | depends on USB_GADGET && PROC_FS | |
63 | help | |
64 | Some of the drivers in the "gadget" framework can expose | |
65 | debugging information in files such as /proc/driver/udc | |
66 | (for a peripheral controller). The information in these | |
67 | files may help when you're troubleshooting or bringing up a | |
68 | driver on a new board. Enable these files by choosing "Y" | |
69 | here. If in doubt, or to conserve kernel memory, say "N". | |
70 | ||
914a3f3b HS |
71 | config USB_GADGET_DEBUG_FS |
72 | boolean "Debugging information files in debugfs" | |
73 | depends on USB_GADGET && DEBUG_FS | |
74 | help | |
75 | Some of the drivers in the "gadget" framework can expose | |
76 | debugging information in files under /sys/kernel/debug/. | |
77 | The information in these files may help when you're | |
78 | troubleshooting or bringing up a driver on a new board. | |
79 | Enable these files by choosing "Y" here. If in doubt, or | |
80 | to conserve kernel memory, say "N". | |
81 | ||
028b271b DB |
82 | config USB_GADGET_SELECTED |
83 | boolean | |
84 | ||
1da177e4 LT |
85 | # |
86 | # USB Peripheral Controller Support | |
87 | # | |
88 | choice | |
89 | prompt "USB Peripheral Controller" | |
90 | depends on USB_GADGET | |
91 | help | |
92 | A USB device uses a controller to talk to its host. | |
93 | Systems should have only one such upstream link. | |
94 | Many controller drivers are platform-specific; these | |
95 | often need board-specific hooks. | |
96 | ||
55d402d8 TD |
97 | config USB_GADGET_AMD5536UDC |
98 | boolean "AMD5536 UDC" | |
99 | depends on PCI | |
100 | select USB_GADGET_DUALSPEED | |
101 | help | |
102 | The AMD5536 UDC is part of the AMD Geode CS5536, an x86 southbridge. | |
103 | It is a USB Highspeed DMA capable USB device controller. Beside ep0 | |
104 | it provides 4 IN and 4 OUT endpoints (bulk or interrupt type). | |
105 | The UDC port supports OTG operation, and may be used as a host port | |
106 | if it's not being used to implement peripheral or OTG roles. | |
107 | ||
108 | Say "y" to link the driver statically, or "m" to build a | |
109 | dynamically linked module called "amd5536udc" and force all | |
110 | gadget drivers to also be dynamically linked. | |
111 | ||
112 | config USB_AMD5536UDC | |
113 | tristate | |
114 | depends on USB_GADGET_AMD5536UDC | |
115 | default USB_GADGET | |
116 | select USB_GADGET_SELECTED | |
117 | ||
914a3f3b HS |
118 | config USB_GADGET_ATMEL_USBA |
119 | boolean "Atmel USBA" | |
120 | select USB_GADGET_DUALSPEED | |
121 | depends on AVR32 | |
122 | help | |
123 | USBA is the integrated high-speed USB Device controller on | |
124 | the AT32AP700x processors from Atmel. | |
125 | ||
126 | config USB_ATMEL_USBA | |
127 | tristate | |
128 | depends on USB_GADGET_ATMEL_USBA | |
129 | default USB_GADGET | |
130 | select USB_GADGET_SELECTED | |
131 | ||
b504882d LY |
132 | config USB_GADGET_FSL_USB2 |
133 | boolean "Freescale Highspeed USB DR Peripheral Controller" | |
134 | depends on MPC834x || PPC_MPC831x | |
135 | select USB_GADGET_DUALSPEED | |
136 | help | |
137 | Some of Freescale PowerPC processors have a High Speed | |
138 | Dual-Role(DR) USB controller, which supports device mode. | |
139 | ||
140 | The number of programmable endpoints is different through | |
141 | SOC revisions. | |
142 | ||
143 | Say "y" to link the driver statically, or "m" to build a | |
144 | dynamically linked module called "fsl_usb2_udc" and force | |
145 | all gadget drivers to also be dynamically linked. | |
146 | ||
147 | config USB_FSL_USB2 | |
148 | tristate | |
149 | depends on USB_GADGET_FSL_USB2 | |
150 | default USB_GADGET | |
151 | select USB_GADGET_SELECTED | |
152 | ||
1da177e4 | 153 | config USB_GADGET_NET2280 |
950ee4c8 | 154 | boolean "NetChip 228x" |
1da177e4 LT |
155 | depends on PCI |
156 | select USB_GADGET_DUALSPEED | |
157 | help | |
950ee4c8 | 158 | NetChip 2280 / 2282 is a PCI based USB peripheral controller which |
1da177e4 LT |
159 | supports both full and high speed USB 2.0 data transfers. |
160 | ||
161 | It has six configurable endpoints, as well as endpoint zero | |
162 | (for control transfers) and several endpoints with dedicated | |
163 | functions. | |
164 | ||
165 | Say "y" to link the driver statically, or "m" to build a | |
166 | dynamically linked module called "net2280" and force all | |
167 | gadget drivers to also be dynamically linked. | |
168 | ||
169 | config USB_NET2280 | |
170 | tristate | |
171 | depends on USB_GADGET_NET2280 | |
172 | default USB_GADGET | |
028b271b | 173 | select USB_GADGET_SELECTED |
1da177e4 LT |
174 | |
175 | config USB_GADGET_PXA2XX | |
176 | boolean "PXA 25x or IXP 4xx" | |
177 | depends on (ARCH_PXA && PXA25x) || ARCH_IXP4XX | |
178 | help | |
179 | Intel's PXA 25x series XScale ARM-5TE processors include | |
180 | an integrated full speed USB 1.1 device controller. The | |
181 | controller in the IXP 4xx series is register-compatible. | |
182 | ||
183 | It has fifteen fixed-function endpoints, as well as endpoint | |
184 | zero (for control transfers). | |
185 | ||
186 | Say "y" to link the driver statically, or "m" to build a | |
187 | dynamically linked module called "pxa2xx_udc" and force all | |
188 | gadget drivers to also be dynamically linked. | |
189 | ||
190 | config USB_PXA2XX | |
191 | tristate | |
192 | depends on USB_GADGET_PXA2XX | |
193 | default USB_GADGET | |
028b271b | 194 | select USB_GADGET_SELECTED |
1da177e4 LT |
195 | |
196 | # if there's only one gadget driver, using only two bulk endpoints, | |
197 | # don't waste memory for the other endpoints | |
198 | config USB_PXA2XX_SMALL | |
199 | depends on USB_GADGET_PXA2XX | |
200 | bool | |
201 | default n if USB_ETH_RNDIS | |
202 | default y if USB_ZERO | |
203 | default y if USB_ETH | |
204 | default y if USB_G_SERIAL | |
205 | ||
598f22e1 YS |
206 | config USB_GADGET_M66592 |
207 | boolean "Renesas M66592 USB Peripheral Controller" | |
208 | select USB_GADGET_DUALSPEED | |
209 | help | |
210 | M66592 is a discrete USB peripheral controller chip that | |
211 | supports both full and high speed USB 2.0 data transfers. | |
212 | It has seven configurable endpoints, and endpoint zero. | |
213 | ||
214 | Say "y" to link the driver statically, or "m" to build a | |
215 | dynamically linked module called "m66592_udc" and force all | |
216 | gadget drivers to also be dynamically linked. | |
217 | ||
218 | config USB_M66592 | |
219 | tristate | |
220 | depends on USB_GADGET_M66592 | |
221 | default USB_GADGET | |
222 | select USB_GADGET_SELECTED | |
223 | ||
8c73aff6 YS |
224 | config SUPERH_BUILT_IN_M66592 |
225 | boolean "Enable SuperH built-in USB like the M66592" | |
226 | depends on USB_GADGET_M66592 && CPU_SUBTYPE_SH7722 | |
227 | help | |
228 | SH7722 has USB like the M66592. | |
229 | ||
230 | The transfer rate is very slow when use "Ethernet Gadget". | |
231 | However, this problem is improved if change a value of | |
232 | NET_IP_ALIGN to 4. | |
233 | ||
1da177e4 LT |
234 | config USB_GADGET_GOKU |
235 | boolean "Toshiba TC86C001 'Goku-S'" | |
236 | depends on PCI | |
237 | help | |
238 | The Toshiba TC86C001 is a PCI device which includes controllers | |
239 | for full speed USB devices, IDE, I2C, SIO, plus a USB host (OHCI). | |
240 | ||
241 | The device controller has three configurable (bulk or interrupt) | |
242 | endpoints, plus endpoint zero (for control transfers). | |
243 | ||
244 | Say "y" to link the driver statically, or "m" to build a | |
245 | dynamically linked module called "goku_udc" and to force all | |
246 | gadget drivers to also be dynamically linked. | |
247 | ||
248 | config USB_GOKU | |
249 | tristate | |
250 | depends on USB_GADGET_GOKU | |
251 | default USB_GADGET | |
028b271b | 252 | select USB_GADGET_SELECTED |
1da177e4 LT |
253 | |
254 | ||
255 | config USB_GADGET_LH7A40X | |
256 | boolean "LH7A40X" | |
257 | depends on ARCH_LH7A40X | |
258 | help | |
259 | This driver provides USB Device Controller driver for LH7A40x | |
260 | ||
261 | config USB_LH7A40X | |
262 | tristate | |
263 | depends on USB_GADGET_LH7A40X | |
264 | default USB_GADGET | |
028b271b | 265 | select USB_GADGET_SELECTED |
1da177e4 | 266 | |
1da177e4 LT |
267 | config USB_GADGET_OMAP |
268 | boolean "OMAP USB Device Controller" | |
269 | depends on ARCH_OMAP | |
270 | select ISP1301_OMAP if MACH_OMAP_H2 || MACH_OMAP_H3 | |
271 | help | |
272 | Many Texas Instruments OMAP processors have flexible full | |
273 | speed USB device controllers, with support for up to 30 | |
274 | endpoints (plus endpoint zero). This driver supports the | |
275 | controller in the OMAP 1611, and should work with controllers | |
276 | in other OMAP processors too, given minor tweaks. | |
277 | ||
278 | Say "y" to link the driver statically, or "m" to build a | |
279 | dynamically linked module called "omap_udc" and force all | |
280 | gadget drivers to also be dynamically linked. | |
281 | ||
282 | config USB_OMAP | |
283 | tristate | |
284 | depends on USB_GADGET_OMAP | |
285 | default USB_GADGET | |
028b271b | 286 | select USB_GADGET_SELECTED |
1da177e4 LT |
287 | |
288 | config USB_OTG | |
289 | boolean "OTG Support" | |
290 | depends on USB_GADGET_OMAP && ARCH_OMAP_OTG && USB_OHCI_HCD | |
291 | help | |
292 | The most notable feature of USB OTG is support for a | |
293 | "Dual-Role" device, which can act as either a device | |
294 | or a host. The initial role choice can be changed | |
295 | later, when two dual-role devices talk to each other. | |
296 | ||
297 | Select this only if your OMAP board has a Mini-AB connector. | |
298 | ||
3fc154b6 AP |
299 | config USB_GADGET_S3C2410 |
300 | boolean "S3C2410 USB Device Controller" | |
301 | depends on ARCH_S3C2410 | |
302 | help | |
303 | Samsung's S3C2410 is an ARM-4 processor with an integrated | |
304 | full speed USB 1.1 device controller. It has 4 configurable | |
305 | endpoints, as well as endpoint zero (for control transfers). | |
306 | ||
307 | This driver has been tested on the S3C2410, S3C2412, and | |
308 | S3C2440 processors. | |
309 | ||
310 | config USB_S3C2410 | |
311 | tristate | |
312 | depends on USB_GADGET_S3C2410 | |
313 | default USB_GADGET | |
314 | select USB_GADGET_SELECTED | |
315 | ||
316 | config USB_S3C2410_DEBUG | |
317 | boolean "S3C2410 udc debug messages" | |
318 | depends on USB_GADGET_S3C2410 | |
319 | ||
bae4bd84 DB |
320 | config USB_GADGET_AT91 |
321 | boolean "AT91 USB Device Port" | |
2b3b3516 | 322 | depends on ARCH_AT91 && !ARCH_AT91SAM9RL && !ARCH_AT91CAP9 |
bae4bd84 DB |
323 | select USB_GADGET_SELECTED |
324 | help | |
325 | Many Atmel AT91 processors (such as the AT91RM2000) have a | |
326 | full speed USB Device Port with support for five configurable | |
327 | endpoints (plus endpoint zero). | |
328 | ||
329 | Say "y" to link the driver statically, or "m" to build a | |
330 | dynamically linked module called "at91_udc" and force all | |
331 | gadget drivers to also be dynamically linked. | |
332 | ||
333 | config USB_AT91 | |
334 | tristate | |
335 | depends on USB_GADGET_AT91 | |
336 | default USB_GADGET | |
1da177e4 LT |
337 | |
338 | config USB_GADGET_DUMMY_HCD | |
339 | boolean "Dummy HCD (DEVELOPMENT)" | |
be0c8015 | 340 | depends on (USB=y || (USB=m && USB_GADGET=m)) && EXPERIMENTAL |
1da177e4 LT |
341 | select USB_GADGET_DUALSPEED |
342 | help | |
343 | This host controller driver emulates USB, looping all data transfer | |
344 | requests back to a USB "gadget driver" in the same host. The host | |
345 | side is the master; the gadget side is the slave. Gadget drivers | |
346 | can be high, full, or low speed; and they have access to endpoints | |
347 | like those from NET2280, PXA2xx, or SA1100 hardware. | |
348 | ||
349 | This may help in some stages of creating a driver to embed in a | |
350 | Linux device, since it lets you debug several parts of the gadget | |
351 | driver without its hardware or drivers being involved. | |
352 | ||
353 | Since such a gadget side driver needs to interoperate with a host | |
354 | side Linux-USB device driver, this may help to debug both sides | |
355 | of a USB protocol stack. | |
356 | ||
357 | Say "y" to link the driver statically, or "m" to build a | |
358 | dynamically linked module called "dummy_hcd" and force all | |
359 | gadget drivers to also be dynamically linked. | |
360 | ||
361 | config USB_DUMMY_HCD | |
362 | tristate | |
363 | depends on USB_GADGET_DUMMY_HCD | |
364 | default USB_GADGET | |
028b271b | 365 | select USB_GADGET_SELECTED |
1da177e4 LT |
366 | |
367 | # NOTE: Please keep dummy_hcd LAST so that "real hardware" appears | |
368 | # first and will be selected by default. | |
369 | ||
370 | endchoice | |
371 | ||
372 | config USB_GADGET_DUALSPEED | |
373 | bool | |
374 | depends on USB_GADGET | |
375 | default n | |
376 | help | |
377 | Means that gadget drivers should include extra descriptors | |
378 | and code to handle dual-speed controllers. | |
379 | ||
380 | # | |
381 | # USB Gadget Drivers | |
382 | # | |
383 | choice | |
384 | tristate "USB Gadget Drivers" | |
028b271b | 385 | depends on USB_GADGET && USB_GADGET_SELECTED |
1da177e4 LT |
386 | default USB_ETH |
387 | help | |
388 | A Linux "Gadget Driver" talks to the USB Peripheral Controller | |
389 | driver through the abstract "gadget" API. Some other operating | |
390 | systems call these "client" drivers, of which "class drivers" | |
391 | are a subset (implementing a USB device class specification). | |
392 | A gadget driver implements one or more USB functions using | |
393 | the peripheral hardware. | |
394 | ||
395 | Gadget drivers are hardware-neutral, or "platform independent", | |
396 | except that they sometimes must understand quirks or limitations | |
397 | of the particular controllers they work with. For example, when | |
398 | a controller doesn't support alternate configurations or provide | |
399 | enough of the right types of endpoints, the gadget driver might | |
400 | not be able work with that controller, or might need to implement | |
401 | a less common variant of a device class protocol. | |
402 | ||
403 | # this first set of drivers all depend on bulk-capable hardware. | |
404 | ||
405 | config USB_ZERO | |
406 | tristate "Gadget Zero (DEVELOPMENT)" | |
407 | depends on EXPERIMENTAL | |
408 | help | |
409 | Gadget Zero is a two-configuration device. It either sinks and | |
410 | sources bulk data; or it loops back a configurable number of | |
411 | transfers. It also implements control requests, for "chapter 9" | |
412 | conformance. The driver needs only two bulk-capable endpoints, so | |
413 | it can work on top of most device-side usb controllers. It's | |
414 | useful for testing, and is also a working example showing how | |
415 | USB "gadget drivers" can be written. | |
416 | ||
417 | Make this be the first driver you try using on top of any new | |
418 | USB peripheral controller driver. Then you can use host-side | |
419 | test software, like the "usbtest" driver, to put your hardware | |
420 | and its driver through a basic set of functional tests. | |
421 | ||
422 | Gadget Zero also works with the host-side "usb-skeleton" driver, | |
423 | and with many kinds of host-side test software. You may need | |
424 | to tweak product and vendor IDs before host software knows about | |
425 | this device, and arrange to select an appropriate configuration. | |
426 | ||
427 | Say "y" to link the driver statically, or "m" to build a | |
428 | dynamically linked module called "g_zero". | |
429 | ||
430 | config USB_ZERO_HNPTEST | |
431 | boolean "HNP Test Device" | |
432 | depends on USB_ZERO && USB_OTG | |
433 | help | |
434 | You can configure this device to enumerate using the device | |
435 | identifiers of the USB-OTG test device. That means that when | |
436 | this gadget connects to another OTG device, with this one using | |
437 | the "B-Peripheral" role, that device will use HNP to let this | |
438 | one serve as the USB host instead (in the "B-Host" role). | |
439 | ||
440 | config USB_ETH | |
441 | tristate "Ethernet Gadget (with CDC Ethernet support)" | |
442 | depends on NET | |
443 | help | |
444 | This driver implements Ethernet style communication, in either | |
445 | of two ways: | |
446 | ||
447 | - The "Communication Device Class" (CDC) Ethernet Control Model. | |
448 | That protocol is often avoided with pure Ethernet adapters, in | |
449 | favor of simpler vendor-specific hardware, but is widely | |
450 | supported by firmware for smart network devices. | |
451 | ||
452 | - On hardware can't implement that protocol, a simple CDC subset | |
453 | is used, placing fewer demands on USB. | |
454 | ||
455 | RNDIS support is a third option, more demanding than that subset. | |
456 | ||
457 | Within the USB device, this gadget driver exposes a network device | |
458 | "usbX", where X depends on what other networking devices you have. | |
459 | Treat it like a two-node Ethernet link: host, and gadget. | |
460 | ||
461 | The Linux-USB host-side "usbnet" driver interoperates with this | |
462 | driver, so that deep I/O queues can be supported. On 2.4 kernels, | |
463 | use "CDCEther" instead, if you're using the CDC option. That CDC | |
464 | mode should also interoperate with standard CDC Ethernet class | |
465 | drivers on other host operating systems. | |
466 | ||
467 | Say "y" to link the driver statically, or "m" to build a | |
468 | dynamically linked module called "g_ether". | |
469 | ||
470 | config USB_ETH_RNDIS | |
471 | bool "RNDIS support (EXPERIMENTAL)" | |
472 | depends on USB_ETH && EXPERIMENTAL | |
473 | default y | |
474 | help | |
475 | Microsoft Windows XP bundles the "Remote NDIS" (RNDIS) protocol, | |
476 | and Microsoft provides redistributable binary RNDIS drivers for | |
477 | older versions of Windows. | |
478 | ||
479 | If you say "y" here, the Ethernet gadget driver will try to provide | |
480 | a second device configuration, supporting RNDIS to talk to such | |
481 | Microsoft USB hosts. | |
482 | ||
483 | To make MS-Windows work with this, use Documentation/usb/linux.inf | |
484 | as the "driver info file". For versions of MS-Windows older than | |
485 | XP, you'll need to download drivers from Microsoft's website; a URL | |
486 | is given in comments found in that info file. | |
487 | ||
488 | config USB_GADGETFS | |
489 | tristate "Gadget Filesystem (EXPERIMENTAL)" | |
490 | depends on EXPERIMENTAL | |
491 | help | |
492 | This driver provides a filesystem based API that lets user mode | |
493 | programs implement a single-configuration USB device, including | |
494 | endpoint I/O and control requests that don't relate to enumeration. | |
495 | All endpoints, transfer speeds, and transfer types supported by | |
496 | the hardware are available, through read() and write() calls. | |
497 | ||
498 | Say "y" to link the driver statically, or "m" to build a | |
499 | dynamically linked module called "gadgetfs". | |
500 | ||
501 | config USB_FILE_STORAGE | |
502 | tristate "File-backed Storage Gadget" | |
87840289 | 503 | depends on BLOCK |
1da177e4 LT |
504 | help |
505 | The File-backed Storage Gadget acts as a USB Mass Storage | |
506 | disk drive. As its storage repository it can use a regular | |
507 | file or a block device (in much the same way as the "loop" | |
508 | device driver), specified as a module parameter. | |
509 | ||
510 | Say "y" to link the driver statically, or "m" to build a | |
511 | dynamically linked module called "g_file_storage". | |
512 | ||
513 | config USB_FILE_STORAGE_TEST | |
514 | bool "File-backed Storage Gadget testing version" | |
515 | depends on USB_FILE_STORAGE | |
516 | default n | |
517 | help | |
518 | Say "y" to generate the larger testing version of the | |
519 | File-backed Storage Gadget, useful for probing the | |
520 | behavior of USB Mass Storage hosts. Not needed for | |
521 | normal operation. | |
522 | ||
523 | config USB_G_SERIAL | |
524 | tristate "Serial Gadget (with CDC ACM support)" | |
525 | help | |
526 | The Serial Gadget talks to the Linux-USB generic serial driver. | |
527 | This driver supports a CDC-ACM module option, which can be used | |
528 | to interoperate with MS-Windows hosts or with the Linux-USB | |
529 | "cdc-acm" driver. | |
530 | ||
531 | Say "y" to link the driver statically, or "m" to build a | |
532 | dynamically linked module called "g_serial". | |
533 | ||
534 | For more information, see Documentation/usb/gadget_serial.txt | |
535 | which includes instructions and a "driver info file" needed to | |
536 | make MS-Windows work with this driver. | |
537 | ||
f2ebf92c BW |
538 | config USB_MIDI_GADGET |
539 | tristate "MIDI Gadget (EXPERIMENTAL)" | |
540 | depends on SND && EXPERIMENTAL | |
541 | select SND_RAWMIDI | |
542 | help | |
543 | The MIDI Gadget acts as a USB Audio device, with one MIDI | |
544 | input and one MIDI output. These MIDI jacks appear as | |
545 | a sound "card" in the ALSA sound system. Other MIDI | |
546 | connections can then be made on the gadget system, using | |
547 | ALSA's aconnect utility etc. | |
548 | ||
549 | Say "y" to link the driver statically, or "m" to build a | |
550 | dynamically linked module called "g_midi". | |
551 | ||
25a010c8 CN |
552 | config USB_G_PRINTER |
553 | tristate "Printer Gadget" | |
554 | help | |
555 | The Printer Gadget channels data between the USB host and a | |
556 | userspace program driving the print engine. The user space | |
557 | program reads and writes the device file /dev/g_printer to | |
558 | receive or send printer data. It can use ioctl calls to | |
559 | the device file to get or set printer status. | |
560 | ||
561 | Say "y" to link the driver statically, or "m" to build a | |
562 | dynamically linked module called "g_printer". | |
563 | ||
564 | For more information, see Documentation/usb/gadget_printer.txt | |
565 | which includes sample code for accessing the device file. | |
1da177e4 LT |
566 | |
567 | # put drivers that need isochronous transfer support (for audio | |
568 | # or video class gadget drivers), or specific hardware, here. | |
569 | ||
570 | # - none yet | |
571 | ||
572 | endchoice | |
573 | ||
b75be4ab | 574 | endif # USB_GADGET |