]>
Commit | Line | Data |
---|---|---|
b2441318 | 1 | /* SPDX-License-Identifier: GPL-2.0 */ |
b92a78e5 RG |
2 | /* |
3 | * Host interface registers | |
4 | */ | |
5 | ||
6 | #define OXU_DEVICEID 0x00 | |
7 | #define OXU_REV_MASK 0xffff0000 | |
8 | #define OXU_REV_SHIFT 16 | |
9 | #define OXU_REV_2100 0x2100 | |
10 | #define OXU_BO_SHIFT 8 | |
11 | #define OXU_BO_MASK (0x3 << OXU_BO_SHIFT) | |
12 | #define OXU_MAJ_REV_SHIFT 4 | |
13 | #define OXU_MAJ_REV_MASK (0xf << OXU_MAJ_REV_SHIFT) | |
14 | #define OXU_MIN_REV_SHIFT 0 | |
15 | #define OXU_MIN_REV_MASK (0xf << OXU_MIN_REV_SHIFT) | |
16 | #define OXU_HOSTIFCONFIG 0x04 | |
17 | #define OXU_SOFTRESET 0x08 | |
18 | #define OXU_SRESET (1 << 0) | |
19 | ||
20 | #define OXU_PIOBURSTREADCTRL 0x0C | |
21 | ||
22 | #define OXU_CHIPIRQSTATUS 0x10 | |
23 | #define OXU_CHIPIRQEN_SET 0x14 | |
24 | #define OXU_CHIPIRQEN_CLR 0x18 | |
25 | #define OXU_USBSPHLPWUI 0x00000080 | |
26 | #define OXU_USBOTGLPWUI 0x00000040 | |
27 | #define OXU_USBSPHI 0x00000002 | |
28 | #define OXU_USBOTGI 0x00000001 | |
29 | ||
30 | #define OXU_CLKCTRL_SET 0x1C | |
31 | #define OXU_SYSCLKEN 0x00000008 | |
32 | #define OXU_USBSPHCLKEN 0x00000002 | |
33 | #define OXU_USBOTGCLKEN 0x00000001 | |
34 | ||
35 | #define OXU_ASO 0x68 | |
36 | #define OXU_SPHPOEN 0x00000100 | |
37 | #define OXU_OVRCCURPUPDEN 0x00000800 | |
38 | #define OXU_ASO_OP (1 << 10) | |
39 | #define OXU_COMPARATOR 0x000004000 | |
40 | ||
41 | #define OXU_USBMODE 0x1A8 | |
42 | #define OXU_VBPS 0x00000020 | |
43 | #define OXU_ES_LITTLE 0x00000000 | |
44 | #define OXU_CM_HOST_ONLY 0x00000003 | |
45 | ||
46 | /* | |
47 | * Proper EHCI structs & defines | |
48 | */ | |
49 | ||
50 | /* Magic numbers that can affect system performance */ | |
51 | #define EHCI_TUNE_CERR 3 /* 0-3 qtd retries; 0 == don't stop */ | |
52 | #define EHCI_TUNE_RL_HS 4 /* nak throttle; see 4.9 */ | |
53 | #define EHCI_TUNE_RL_TT 0 | |
54 | #define EHCI_TUNE_MULT_HS 1 /* 1-3 transactions/uframe; 4.10.3 */ | |
55 | #define EHCI_TUNE_MULT_TT 1 | |
56 | #define EHCI_TUNE_FLS 2 /* (small) 256 frame schedule */ | |
57 | ||
58 | struct oxu_hcd; | |
59 | ||
60 | /* EHCI register interface, corresponds to EHCI Revision 0.95 specification */ | |
61 | ||
62 | /* Section 2.2 Host Controller Capability Registers */ | |
63 | struct ehci_caps { | |
64 | /* these fields are specified as 8 and 16 bit registers, | |
65 | * but some hosts can't perform 8 or 16 bit PCI accesses. | |
66 | */ | |
67 | u32 hc_capbase; | |
68 | #define HC_LENGTH(p) (((p)>>00)&0x00ff) /* bits 7:0 */ | |
69 | #define HC_VERSION(p) (((p)>>16)&0xffff) /* bits 31:16 */ | |
70 | u32 hcs_params; /* HCSPARAMS - offset 0x4 */ | |
71 | #define HCS_DEBUG_PORT(p) (((p)>>20)&0xf) /* bits 23:20, debug port? */ | |
72 | #define HCS_INDICATOR(p) ((p)&(1 << 16)) /* true: has port indicators */ | |
73 | #define HCS_N_CC(p) (((p)>>12)&0xf) /* bits 15:12, #companion HCs */ | |
74 | #define HCS_N_PCC(p) (((p)>>8)&0xf) /* bits 11:8, ports per CC */ | |
75 | #define HCS_PORTROUTED(p) ((p)&(1 << 7)) /* true: port routing */ | |
76 | #define HCS_PPC(p) ((p)&(1 << 4)) /* true: port power control */ | |
77 | #define HCS_N_PORTS(p) (((p)>>0)&0xf) /* bits 3:0, ports on HC */ | |
78 | ||
79 | u32 hcc_params; /* HCCPARAMS - offset 0x8 */ | |
80 | #define HCC_EXT_CAPS(p) (((p)>>8)&0xff) /* for pci extended caps */ | |
81 | #define HCC_ISOC_CACHE(p) ((p)&(1 << 7)) /* true: can cache isoc frame */ | |
82 | #define HCC_ISOC_THRES(p) (((p)>>4)&0x7) /* bits 6:4, uframes cached */ | |
83 | #define HCC_CANPARK(p) ((p)&(1 << 2)) /* true: can park on async qh */ | |
84 | #define HCC_PGM_FRAMELISTLEN(p) ((p)&(1 << 1)) /* true: periodic_size changes*/ | |
85 | #define HCC_64BIT_ADDR(p) ((p)&(1)) /* true: can use 64-bit addr */ | |
86 | u8 portroute[8]; /* nibbles for routing - offset 0xC */ | |
87 | } __attribute__ ((packed)); | |
88 | ||
89 | ||
90 | /* Section 2.3 Host Controller Operational Registers */ | |
91 | struct ehci_regs { | |
92 | /* USBCMD: offset 0x00 */ | |
93 | u32 command; | |
94 | /* 23:16 is r/w intr rate, in microframes; default "8" == 1/msec */ | |
95 | #define CMD_PARK (1<<11) /* enable "park" on async qh */ | |
96 | #define CMD_PARK_CNT(c) (((c)>>8)&3) /* how many transfers to park for */ | |
97 | #define CMD_LRESET (1<<7) /* partial reset (no ports, etc) */ | |
98 | #define CMD_IAAD (1<<6) /* "doorbell" interrupt async advance */ | |
99 | #define CMD_ASE (1<<5) /* async schedule enable */ | |
100 | #define CMD_PSE (1<<4) /* periodic schedule enable */ | |
101 | /* 3:2 is periodic frame list size */ | |
102 | #define CMD_RESET (1<<1) /* reset HC not bus */ | |
103 | #define CMD_RUN (1<<0) /* start/stop HC */ | |
104 | ||
105 | /* USBSTS: offset 0x04 */ | |
106 | u32 status; | |
107 | #define STS_ASS (1<<15) /* Async Schedule Status */ | |
108 | #define STS_PSS (1<<14) /* Periodic Schedule Status */ | |
109 | #define STS_RECL (1<<13) /* Reclamation */ | |
110 | #define STS_HALT (1<<12) /* Not running (any reason) */ | |
111 | /* some bits reserved */ | |
112 | /* these STS_* flags are also intr_enable bits (USBINTR) */ | |
113 | #define STS_IAA (1<<5) /* Interrupted on async advance */ | |
114 | #define STS_FATAL (1<<4) /* such as some PCI access errors */ | |
115 | #define STS_FLR (1<<3) /* frame list rolled over */ | |
116 | #define STS_PCD (1<<2) /* port change detect */ | |
117 | #define STS_ERR (1<<1) /* "error" completion (overflow, ...) */ | |
118 | #define STS_INT (1<<0) /* "normal" completion (short, ...) */ | |
119 | ||
120 | #define INTR_MASK (STS_IAA | STS_FATAL | STS_PCD | STS_ERR | STS_INT) | |
121 | ||
122 | /* USBINTR: offset 0x08 */ | |
123 | u32 intr_enable; | |
124 | ||
125 | /* FRINDEX: offset 0x0C */ | |
126 | u32 frame_index; /* current microframe number */ | |
127 | /* CTRLDSSEGMENT: offset 0x10 */ | |
128 | u32 segment; /* address bits 63:32 if needed */ | |
129 | /* PERIODICLISTBASE: offset 0x14 */ | |
130 | u32 frame_list; /* points to periodic list */ | |
131 | /* ASYNCLISTADDR: offset 0x18 */ | |
132 | u32 async_next; /* address of next async queue head */ | |
133 | ||
134 | u32 reserved[9]; | |
135 | ||
136 | /* CONFIGFLAG: offset 0x40 */ | |
137 | u32 configured_flag; | |
138 | #define FLAG_CF (1<<0) /* true: we'll support "high speed" */ | |
139 | ||
140 | /* PORTSC: offset 0x44 */ | |
141 | u32 port_status[0]; /* up to N_PORTS */ | |
142 | /* 31:23 reserved */ | |
143 | #define PORT_WKOC_E (1<<22) /* wake on overcurrent (enable) */ | |
144 | #define PORT_WKDISC_E (1<<21) /* wake on disconnect (enable) */ | |
145 | #define PORT_WKCONN_E (1<<20) /* wake on connect (enable) */ | |
146 | /* 19:16 for port testing */ | |
147 | #define PORT_LED_OFF (0<<14) | |
148 | #define PORT_LED_AMBER (1<<14) | |
149 | #define PORT_LED_GREEN (2<<14) | |
150 | #define PORT_LED_MASK (3<<14) | |
151 | #define PORT_OWNER (1<<13) /* true: companion hc owns this port */ | |
152 | #define PORT_POWER (1<<12) /* true: has power (see PPC) */ | |
153 | #define PORT_USB11(x) (((x)&(3<<10)) == (1<<10)) /* USB 1.1 device */ | |
154 | /* 11:10 for detecting lowspeed devices (reset vs release ownership) */ | |
155 | /* 9 reserved */ | |
156 | #define PORT_RESET (1<<8) /* reset port */ | |
157 | #define PORT_SUSPEND (1<<7) /* suspend port */ | |
158 | #define PORT_RESUME (1<<6) /* resume it */ | |
159 | #define PORT_OCC (1<<5) /* over current change */ | |
160 | #define PORT_OC (1<<4) /* over current active */ | |
161 | #define PORT_PEC (1<<3) /* port enable change */ | |
162 | #define PORT_PE (1<<2) /* port enable */ | |
163 | #define PORT_CSC (1<<1) /* connect status change */ | |
164 | #define PORT_CONNECT (1<<0) /* device connected */ | |
165 | #define PORT_RWC_BITS (PORT_CSC | PORT_PEC | PORT_OCC) | |
166 | } __attribute__ ((packed)); | |
167 | ||
168 | /* Appendix C, Debug port ... intended for use with special "debug devices" | |
169 | * that can help if there's no serial console. (nonstandard enumeration.) | |
170 | */ | |
171 | struct ehci_dbg_port { | |
172 | u32 control; | |
173 | #define DBGP_OWNER (1<<30) | |
174 | #define DBGP_ENABLED (1<<28) | |
175 | #define DBGP_DONE (1<<16) | |
176 | #define DBGP_INUSE (1<<10) | |
177 | #define DBGP_ERRCODE(x) (((x)>>7)&0x07) | |
178 | # define DBGP_ERR_BAD 1 | |
179 | # define DBGP_ERR_SIGNAL 2 | |
180 | #define DBGP_ERROR (1<<6) | |
181 | #define DBGP_GO (1<<5) | |
182 | #define DBGP_OUT (1<<4) | |
183 | #define DBGP_LEN(x) (((x)>>0)&0x0f) | |
184 | u32 pids; | |
185 | #define DBGP_PID_GET(x) (((x)>>16)&0xff) | |
186 | #define DBGP_PID_SET(data, tok) (((data)<<8)|(tok)) | |
187 | u32 data03; | |
188 | u32 data47; | |
189 | u32 address; | |
190 | #define DBGP_EPADDR(dev, ep) (((dev)<<8)|(ep)) | |
191 | } __attribute__ ((packed)); | |
192 | ||
193 | ||
194 | #define QTD_NEXT(dma) cpu_to_le32((u32)dma) | |
195 | ||
196 | /* | |
197 | * EHCI Specification 0.95 Section 3.5 | |
198 | * QTD: describe data transfer components (buffer, direction, ...) | |
199 | * See Fig 3-6 "Queue Element Transfer Descriptor Block Diagram". | |
200 | * | |
201 | * These are associated only with "QH" (Queue Head) structures, | |
202 | * used with control, bulk, and interrupt transfers. | |
203 | */ | |
204 | struct ehci_qtd { | |
205 | /* first part defined by EHCI spec */ | |
206 | __le32 hw_next; /* see EHCI 3.5.1 */ | |
207 | __le32 hw_alt_next; /* see EHCI 3.5.2 */ | |
208 | __le32 hw_token; /* see EHCI 3.5.3 */ | |
209 | #define QTD_TOGGLE (1 << 31) /* data toggle */ | |
210 | #define QTD_LENGTH(tok) (((tok)>>16) & 0x7fff) | |
211 | #define QTD_IOC (1 << 15) /* interrupt on complete */ | |
212 | #define QTD_CERR(tok) (((tok)>>10) & 0x3) | |
213 | #define QTD_PID(tok) (((tok)>>8) & 0x3) | |
214 | #define QTD_STS_ACTIVE (1 << 7) /* HC may execute this */ | |
215 | #define QTD_STS_HALT (1 << 6) /* halted on error */ | |
216 | #define QTD_STS_DBE (1 << 5) /* data buffer error (in HC) */ | |
217 | #define QTD_STS_BABBLE (1 << 4) /* device was babbling (qtd halted) */ | |
218 | #define QTD_STS_XACT (1 << 3) /* device gave illegal response */ | |
219 | #define QTD_STS_MMF (1 << 2) /* incomplete split transaction */ | |
220 | #define QTD_STS_STS (1 << 1) /* split transaction state */ | |
221 | #define QTD_STS_PING (1 << 0) /* issue PING? */ | |
222 | __le32 hw_buf[5]; /* see EHCI 3.5.4 */ | |
223 | __le32 hw_buf_hi[5]; /* Appendix B */ | |
224 | ||
225 | /* the rest is HCD-private */ | |
226 | dma_addr_t qtd_dma; /* qtd address */ | |
227 | struct list_head qtd_list; /* sw qtd list */ | |
228 | struct urb *urb; /* qtd's urb */ | |
229 | size_t length; /* length of buffer */ | |
230 | ||
231 | u32 qtd_buffer_len; | |
232 | void *buffer; | |
233 | dma_addr_t buffer_dma; | |
234 | void *transfer_buffer; | |
235 | void *transfer_dma; | |
236 | } __attribute__ ((aligned(32))); | |
237 | ||
238 | /* mask NakCnt+T in qh->hw_alt_next */ | |
551509d2 | 239 | #define QTD_MASK cpu_to_le32 (~0x1f) |
b92a78e5 RG |
240 | |
241 | #define IS_SHORT_READ(token) (QTD_LENGTH(token) != 0 && QTD_PID(token) == 1) | |
242 | ||
243 | /* Type tag from {qh, itd, sitd, fstn}->hw_next */ | |
551509d2 | 244 | #define Q_NEXT_TYPE(dma) ((dma) & cpu_to_le32 (3 << 1)) |
b92a78e5 RG |
245 | |
246 | /* values for that type tag */ | |
551509d2 | 247 | #define Q_TYPE_QH cpu_to_le32 (1 << 1) |
b92a78e5 RG |
248 | |
249 | /* next async queue entry, or pointer to interrupt/periodic QH */ | |
250 | #define QH_NEXT(dma) (cpu_to_le32(((u32)dma)&~0x01f)|Q_TYPE_QH) | |
251 | ||
252 | /* for periodic/async schedules and qtd lists, mark end of list */ | |
551509d2 | 253 | #define EHCI_LIST_END cpu_to_le32(1) /* "null pointer" to hw */ |
b92a78e5 RG |
254 | |
255 | /* | |
256 | * Entries in periodic shadow table are pointers to one of four kinds | |
257 | * of data structure. That's dictated by the hardware; a type tag is | |
258 | * encoded in the low bits of the hardware's periodic schedule. Use | |
259 | * Q_NEXT_TYPE to get the tag. | |
260 | * | |
261 | * For entries in the async schedule, the type tag always says "qh". | |
262 | */ | |
263 | union ehci_shadow { | |
264 | struct ehci_qh *qh; /* Q_TYPE_QH */ | |
265 | __le32 *hw_next; /* (all types) */ | |
266 | void *ptr; | |
267 | }; | |
268 | ||
269 | /* | |
270 | * EHCI Specification 0.95 Section 3.6 | |
271 | * QH: describes control/bulk/interrupt endpoints | |
272 | * See Fig 3-7 "Queue Head Structure Layout". | |
273 | * | |
274 | * These appear in both the async and (for interrupt) periodic schedules. | |
275 | */ | |
276 | ||
277 | struct ehci_qh { | |
278 | /* first part defined by EHCI spec */ | |
279 | __le32 hw_next; /* see EHCI 3.6.1 */ | |
280 | __le32 hw_info1; /* see EHCI 3.6.2 */ | |
281 | #define QH_HEAD 0x00008000 | |
282 | __le32 hw_info2; /* see EHCI 3.6.2 */ | |
283 | #define QH_SMASK 0x000000ff | |
284 | #define QH_CMASK 0x0000ff00 | |
285 | #define QH_HUBADDR 0x007f0000 | |
286 | #define QH_HUBPORT 0x3f800000 | |
287 | #define QH_MULT 0xc0000000 | |
288 | __le32 hw_current; /* qtd list - see EHCI 3.6.4 */ | |
289 | ||
290 | /* qtd overlay (hardware parts of a struct ehci_qtd) */ | |
291 | __le32 hw_qtd_next; | |
292 | __le32 hw_alt_next; | |
293 | __le32 hw_token; | |
294 | __le32 hw_buf[5]; | |
295 | __le32 hw_buf_hi[5]; | |
296 | ||
297 | /* the rest is HCD-private */ | |
298 | dma_addr_t qh_dma; /* address of qh */ | |
299 | union ehci_shadow qh_next; /* ptr to qh; or periodic */ | |
300 | struct list_head qtd_list; /* sw qtd list */ | |
301 | struct ehci_qtd *dummy; | |
302 | struct ehci_qh *reclaim; /* next to reclaim */ | |
303 | ||
304 | struct oxu_hcd *oxu; | |
305 | struct kref kref; | |
306 | unsigned stamp; | |
307 | ||
308 | u8 qh_state; | |
309 | #define QH_STATE_LINKED 1 /* HC sees this */ | |
310 | #define QH_STATE_UNLINK 2 /* HC may still see this */ | |
311 | #define QH_STATE_IDLE 3 /* HC doesn't see this */ | |
312 | #define QH_STATE_UNLINK_WAIT 4 /* LINKED and on reclaim q */ | |
313 | #define QH_STATE_COMPLETING 5 /* don't touch token.HALT */ | |
314 | ||
315 | /* periodic schedule info */ | |
316 | u8 usecs; /* intr bandwidth */ | |
317 | u8 gap_uf; /* uframes split/csplit gap */ | |
318 | u8 c_usecs; /* ... split completion bw */ | |
319 | u16 tt_usecs; /* tt downstream bandwidth */ | |
320 | unsigned short period; /* polling interval */ | |
321 | unsigned short start; /* where polling starts */ | |
322 | #define NO_FRAME ((unsigned short)~0) /* pick new start */ | |
323 | struct usb_device *dev; /* access to TT */ | |
324 | } __attribute__ ((aligned(32))); | |
325 | ||
326 | /* | |
327 | * Proper OXU210HP structs | |
328 | */ | |
329 | ||
330 | #define OXU_OTG_CORE_OFFSET 0x00400 | |
331 | #define OXU_OTG_CAP_OFFSET (OXU_OTG_CORE_OFFSET + 0x100) | |
332 | #define OXU_SPH_CORE_OFFSET 0x00800 | |
333 | #define OXU_SPH_CAP_OFFSET (OXU_SPH_CORE_OFFSET + 0x100) | |
334 | ||
335 | #define OXU_OTG_MEM 0xE000 | |
336 | #define OXU_SPH_MEM 0x16000 | |
337 | ||
338 | /* Only how many elements & element structure are specifies here. */ | |
339 | /* 2 host controllers are enabled - total size <= 28 kbytes */ | |
340 | #define DEFAULT_I_TDPS 1024 | |
341 | #define QHEAD_NUM 16 | |
342 | #define QTD_NUM 32 | |
343 | #define SITD_NUM 8 | |
344 | #define MURB_NUM 8 | |
345 | ||
346 | #define BUFFER_NUM 8 | |
347 | #define BUFFER_SIZE 512 | |
348 | ||
349 | struct oxu_info { | |
350 | struct usb_hcd *hcd[2]; | |
351 | }; | |
352 | ||
353 | struct oxu_buf { | |
354 | u8 buffer[BUFFER_SIZE]; | |
355 | } __attribute__ ((aligned(BUFFER_SIZE))); | |
356 | ||
357 | struct oxu_onchip_mem { | |
358 | struct oxu_buf db_pool[BUFFER_NUM]; | |
359 | ||
360 | u32 frame_list[DEFAULT_I_TDPS]; | |
361 | struct ehci_qh qh_pool[QHEAD_NUM]; | |
362 | struct ehci_qtd qtd_pool[QTD_NUM]; | |
363 | } __attribute__ ((aligned(4 << 10))); | |
364 | ||
365 | #define EHCI_MAX_ROOT_PORTS 15 /* see HCS_N_PORTS */ | |
366 | ||
367 | struct oxu_murb { | |
368 | struct urb urb; | |
369 | struct urb *main; | |
370 | u8 last; | |
371 | }; | |
372 | ||
373 | struct oxu_hcd { /* one per controller */ | |
374 | unsigned int is_otg:1; | |
375 | ||
376 | u8 qh_used[QHEAD_NUM]; | |
377 | u8 qtd_used[QTD_NUM]; | |
378 | u8 db_used[BUFFER_NUM]; | |
379 | u8 murb_used[MURB_NUM]; | |
380 | ||
381 | struct oxu_onchip_mem __iomem *mem; | |
382 | spinlock_t mem_lock; | |
383 | ||
384 | struct timer_list urb_timer; | |
385 | ||
386 | struct ehci_caps __iomem *caps; | |
387 | struct ehci_regs __iomem *regs; | |
388 | ||
389 | __u32 hcs_params; /* cached register copy */ | |
390 | spinlock_t lock; | |
391 | ||
392 | /* async schedule support */ | |
393 | struct ehci_qh *async; | |
394 | struct ehci_qh *reclaim; | |
395 | unsigned reclaim_ready:1; | |
396 | unsigned scanning:1; | |
397 | ||
398 | /* periodic schedule support */ | |
399 | unsigned periodic_size; | |
400 | __le32 *periodic; /* hw periodic table */ | |
401 | dma_addr_t periodic_dma; | |
402 | unsigned i_thresh; /* uframes HC might cache */ | |
403 | ||
404 | union ehci_shadow *pshadow; /* mirror hw periodic table */ | |
405 | int next_uframe; /* scan periodic, start here */ | |
406 | unsigned periodic_sched; /* periodic activity count */ | |
407 | ||
408 | /* per root hub port */ | |
409 | unsigned long reset_done[EHCI_MAX_ROOT_PORTS]; | |
410 | /* bit vectors (one bit per port) */ | |
411 | unsigned long bus_suspended; /* which ports were | |
412 | * already suspended at the | |
413 | * start of a bus suspend | |
414 | */ | |
415 | unsigned long companion_ports;/* which ports are dedicated | |
416 | * to the companion controller | |
417 | */ | |
418 | ||
419 | struct timer_list watchdog; | |
420 | unsigned long actions; | |
421 | unsigned stamp; | |
422 | unsigned long next_statechange; | |
423 | u32 command; | |
424 | ||
425 | /* SILICON QUIRKS */ | |
426 | struct list_head urb_list; /* this is the head to urb | |
427 | * queue that didn't get enough | |
428 | * resources | |
429 | */ | |
430 | struct oxu_murb *murb_pool; /* murb per split big urb */ | |
431 | unsigned urb_len; | |
432 | ||
433 | u8 sbrn; /* packed release number */ | |
434 | }; | |
435 | ||
436 | #define EHCI_IAA_JIFFIES (HZ/100) /* arbitrary; ~10 msec */ | |
437 | #define EHCI_IO_JIFFIES (HZ/10) /* io watchdog > irq_thresh */ | |
438 | #define EHCI_ASYNC_JIFFIES (HZ/20) /* async idle timeout */ | |
439 | #define EHCI_SHRINK_JIFFIES (HZ/200) /* async qh unlink delay */ | |
440 | ||
441 | enum ehci_timer_action { | |
442 | TIMER_IO_WATCHDOG, | |
443 | TIMER_IAA_WATCHDOG, | |
444 | TIMER_ASYNC_SHRINK, | |
445 | TIMER_ASYNC_OFF, | |
446 | }; | |
447 | ||
448 | #include <linux/oxu210hp.h> |