]>
Commit | Line | Data |
---|---|---|
1da177e4 LT |
1 | #ifndef CYPRESS_M8_H |
2 | #define CYPRESS_M8_H | |
3 | ||
4 | /* definitions and function prototypes used for the cypress USB to Serial controller */ | |
5 | ||
6 | /* For sending our feature buffer - controlling serial communication states */ | |
7 | /* Linux HID has no support for serial devices so we do this through the driver */ | |
8 | #define HID_REQ_GET_REPORT 0x01 | |
9 | #define HID_REQ_SET_REPORT 0x09 | |
10 | ||
11 | /* List other cypress USB to Serial devices here, and add them to the id_table */ | |
12 | ||
13 | /* DeLorme Earthmate USB - a GPS device */ | |
14 | #define VENDOR_ID_DELORME 0x1163 | |
15 | #define PRODUCT_ID_EARTHMATEUSB 0x0100 | |
25b6f08e | 16 | #define PRODUCT_ID_EARTHMATEUSB_LT20 0x0200 |
1da177e4 LT |
17 | |
18 | /* Cypress HID->COM RS232 Adapter */ | |
19 | #define VENDOR_ID_CYPRESS 0x04b4 | |
20 | #define PRODUCT_ID_CYPHIDCOM 0x5500 | |
a5c44e29 | 21 | |
6f6f06ee DS |
22 | /* Powercom UPS, chip CY7C63723 */ |
23 | #define VENDOR_ID_POWERCOM 0x0d9f | |
24 | #define PRODUCT_ID_UPS 0x0002 | |
25 | ||
a5c44e29 LM |
26 | /* Nokia CA-42 USB to serial cable */ |
27 | #define VENDOR_ID_DAZZLE 0x07d0 | |
28 | #define PRODUCT_ID_CA42 0x4101 | |
1da177e4 LT |
29 | /* End of device listing */ |
30 | ||
31 | /* Used for setting / requesting serial line settings */ | |
32 | #define CYPRESS_SET_CONFIG 0x01 | |
33 | #define CYPRESS_GET_CONFIG 0x02 | |
34 | ||
35 | /* Used for throttle control */ | |
36 | #define THROTTLED 0x1 | |
37 | #define ACTUALLY_THROTTLED 0x2 | |
38 | ||
39 | /* chiptypes - used in case firmware differs from the generic form ... offering | |
40 | * different baud speeds/etc. | |
41 | */ | |
42 | ||
43 | #define CT_EARTHMATE 0x01 | |
44 | #define CT_CYPHIDCOM 0x02 | |
a5c44e29 | 45 | #define CT_CA42V2 0x03 |
1da177e4 LT |
46 | #define CT_GENERIC 0x0F |
47 | /* End of chiptype definitions */ | |
48 | ||
49 | /* RS-232 serial data communication protocol definitions */ | |
50 | /* these are sent / read at byte 0 of the input/output hid reports */ | |
51 | /* You can find these values defined in the CY4601 USB to Serial design notes */ | |
52 | ||
53 | #define CONTROL_DTR 0x20 /* data terminal ready - flow control - host to device */ | |
54 | #define UART_DSR 0x20 /* data set ready - flow control - device to host */ | |
55 | #define CONTROL_RTS 0x10 /* request to send - flow control - host to device */ | |
56 | #define UART_CTS 0x10 /* clear to send - flow control - device to host */ | |
57 | #define UART_RI 0x10 /* ring indicator - modem - device to host */ | |
58 | #define UART_CD 0x40 /* carrier detect - modem - device to host */ | |
59 | #define CYP_ERROR 0x08 /* received from input report - device to host */ | |
60 | /* Note - the below has nothing to to with the "feature report" reset */ | |
61 | #define CONTROL_RESET 0x08 /* sent with output report - host to device */ | |
62 | ||
63 | /* End of RS-232 protocol definitions */ | |
64 | ||
65 | #endif /* CYPRESS_M8_H */ |