]>
Commit | Line | Data |
---|---|---|
1da177e4 LT |
1 | # |
2 | # Video configuration | |
3 | # | |
4 | ||
5 | menu "Graphics support" | |
e25df120 | 6 | depends on HAS_IOMEM |
1da177e4 | 7 | |
0912e535 NF |
8 | config HAVE_FB_ATMEL |
9 | bool | |
10 | ||
f00117a7 DES |
11 | config SH_MIPI_DSI |
12 | tristate | |
13 | depends on (SUPERH || ARCH_SHMOBILE) && HAVE_CLK | |
14 | ||
15 | config SH_LCD_MIPI_DSI | |
16 | bool | |
17 | ||
179b025f RD |
18 | source "drivers/char/agp/Kconfig" |
19 | ||
deb2d2ec BH |
20 | source "drivers/gpu/vga/Kconfig" |
21 | ||
75471687 TB |
22 | source "drivers/gpu/host1x/Kconfig" |
23 | ||
dee8268f TR |
24 | source "drivers/gpu/drm/Kconfig" |
25 | ||
b2f594fd AD |
26 | config VGASTATE |
27 | tristate | |
28 | default n | |
29 | ||
23b0f015 LY |
30 | config VIDEO_OUTPUT_CONTROL |
31 | tristate "Lowlevel video output switch controls" | |
23b0f015 LY |
32 | help |
33 | This framework adds support for low-level control of the video | |
34 | output switch. | |
35 | ||
a38884f6 TV |
36 | config VIDEOMODE_HELPERS |
37 | bool | |
cc3f414c | 38 | |
f142d3bd TR |
39 | config HDMI |
40 | bool | |
41 | ||
179b025f | 42 | menuconfig FB |
1da177e4 LT |
43 | tristate "Support for frame buffer devices" |
44 | ---help--- | |
45 | The frame buffer device provides an abstraction for the graphics | |
46 | hardware. It represents the frame buffer of some video hardware and | |
47 | allows application software to access the graphics hardware through | |
48 | a well-defined interface, so the software doesn't need to know | |
49 | anything about the low-level (hardware register) stuff. | |
50 | ||
51 | Frame buffer devices work identically across the different | |
52 | architectures supported by Linux and make the implementation of | |
53 | application programs easier and more portable; at this point, an X | |
54 | server exists which uses the frame buffer device exclusively. | |
55 | On several non-X86 architectures, the frame buffer device is the | |
56 | only way to use the graphics hardware. | |
57 | ||
58 | The device is accessed through special device nodes, usually located | |
59 | in the /dev directory, i.e. /dev/fb*. | |
60 | ||
61 | You need an utility program called fbset to make full use of frame | |
62 | buffer devices. Please read <file:Documentation/fb/framebuffer.txt> | |
63 | and the Framebuffer-HOWTO at | |
631dd1a8 | 64 | <http://www.munted.org.uk/programming/Framebuffer-HOWTO-1.3.html> for more |
1da177e4 LT |
65 | information. |
66 | ||
67 | Say Y here and to the driver for your graphics board below if you | |
68 | are compiling a kernel for a non-x86 architecture. | |
69 | ||
70 | If you are compiling for the x86 architecture, you can say Y if you | |
71 | want to play with it, but it is not essential. Please note that | |
72 | running graphical applications that directly touch the hardware | |
73 | (e.g. an accelerated X server) and that are not frame buffer | |
74 | device-aware may cause unexpected results. If unsure, say N. | |
75 | ||
e0e34ef7 JS |
76 | config FIRMWARE_EDID |
77 | bool "Enable firmware EDID" | |
78 | depends on FB | |
79 | default n | |
80 | ---help--- | |
81 | This enables access to the EDID transferred from the firmware. | |
82 | On the i386, this is from the Video BIOS. Enable this if DDC/I2C | |
83 | transfers do not work for your driver and if you are using | |
84 | nvidiafb, i810fb or savagefb. | |
85 | ||
86 | In general, choosing Y for this option is safe. If you | |
87 | experience extremely long delays while booting before you get | |
88 | something on your display, try setting this to N. Matrox cards in | |
89 | combination with certain motherboards and monitors are known to | |
90 | suffer from this problem. | |
91 | ||
fc5891c8 DM |
92 | config FB_DDC |
93 | tristate | |
e0e34ef7 JS |
94 | depends on FB |
95 | select I2C_ALGOBIT | |
96 | select I2C | |
fc5891c8 DM |
97 | default n |
98 | ||
4d31a2b7 MJ |
99 | config FB_BOOT_VESA_SUPPORT |
100 | bool | |
101 | depends on FB | |
102 | default n | |
103 | ---help--- | |
104 | If true, at least one selected framebuffer driver can take advantage | |
105 | of VESA video modes set at an early boot stage via the vga= parameter. | |
106 | ||
1da177e4 LT |
107 | config FB_CFB_FILLRECT |
108 | tristate | |
109 | depends on FB | |
110 | default n | |
111 | ---help--- | |
112 | Include the cfb_fillrect function for generic software rectangle | |
113 | filling. This is used by drivers that don't provide their own | |
114 | (accelerated) version. | |
115 | ||
116 | config FB_CFB_COPYAREA | |
117 | tristate | |
118 | depends on FB | |
119 | default n | |
120 | ---help--- | |
121 | Include the cfb_copyarea function for generic software area copying. | |
122 | This is used by drivers that don't provide their own (accelerated) | |
123 | version. | |
124 | ||
125 | config FB_CFB_IMAGEBLIT | |
126 | tristate | |
127 | depends on FB | |
128 | default n | |
129 | ---help--- | |
130 | Include the cfb_imageblit function for generic software image | |
131 | blitting. This is used by drivers that don't provide their own | |
132 | (accelerated) version. | |
133 | ||
779121e9 PP |
134 | config FB_CFB_REV_PIXELS_IN_BYTE |
135 | bool | |
136 | depends on FB | |
137 | default n | |
138 | ---help--- | |
139 | Allow generic frame-buffer functions to work on displays with 1, 2 | |
140 | and 4 bits per pixel depths which has opposite order of pixels in | |
141 | byte order to bytes in long order. | |
142 | ||
68648ed1 AD |
143 | config FB_SYS_FILLRECT |
144 | tristate | |
145 | depends on FB | |
146 | default n | |
147 | ---help--- | |
148 | Include the sys_fillrect function for generic software rectangle | |
149 | filling. This is used by drivers that don't provide their own | |
150 | (accelerated) version and the framebuffer is in system RAM. | |
151 | ||
152 | config FB_SYS_COPYAREA | |
153 | tristate | |
154 | depends on FB | |
155 | default n | |
156 | ---help--- | |
157 | Include the sys_copyarea function for generic software area copying. | |
158 | This is used by drivers that don't provide their own (accelerated) | |
159 | version and the framebuffer is in system RAM. | |
160 | ||
161 | config FB_SYS_IMAGEBLIT | |
162 | tristate | |
163 | depends on FB | |
164 | default n | |
165 | ---help--- | |
166 | Include the sys_imageblit function for generic software image | |
167 | blitting. This is used by drivers that don't provide their own | |
168 | (accelerated) version and the framebuffer is in system RAM. | |
169 | ||
e4c690e0 AV |
170 | menuconfig FB_FOREIGN_ENDIAN |
171 | bool "Framebuffer foreign endianness support" | |
172 | depends on FB | |
173 | ---help--- | |
174 | This menu will let you enable support for the framebuffers with | |
175 | non-native endianness (e.g. Little-Endian framebuffer on a | |
176 | Big-Endian machine). Most probably you don't have such hardware, | |
177 | so it's safe to say "n" here. | |
178 | ||
179 | choice | |
180 | prompt "Choice endianness support" | |
181 | depends on FB_FOREIGN_ENDIAN | |
182 | ||
183 | config FB_BOTH_ENDIAN | |
184 | bool "Support for Big- and Little-Endian framebuffers" | |
185 | ||
186 | config FB_BIG_ENDIAN | |
187 | bool "Support for Big-Endian framebuffers only" | |
188 | ||
189 | config FB_LITTLE_ENDIAN | |
190 | bool "Support for Little-Endian framebuffers only" | |
191 | ||
192 | endchoice | |
193 | ||
09aaf268 AD |
194 | config FB_SYS_FOPS |
195 | tristate | |
196 | depends on FB | |
197 | default n | |
198 | ||
60b59bea JK |
199 | config FB_DEFERRED_IO |
200 | bool | |
201 | depends on FB | |
60b59bea | 202 | |
0e27aa3d JK |
203 | config FB_HECUBA |
204 | tristate | |
205 | depends on FB | |
206 | depends on FB_DEFERRED_IO | |
207 | ||
a268422d OZ |
208 | config FB_SVGALIB |
209 | tristate | |
210 | depends on FB | |
211 | default n | |
212 | ---help--- | |
213 | Common utility functions useful to fbdev drivers of VGA-based | |
214 | cards. | |
215 | ||
1da177e4 LT |
216 | config FB_MACMODES |
217 | tristate | |
218 | depends on FB | |
219 | default n | |
220 | ||
5474c120 | 221 | config FB_BACKLIGHT |
4b755999 MH |
222 | bool |
223 | depends on FB | |
224 | select BACKLIGHT_LCD_SUPPORT | |
225 | select BACKLIGHT_CLASS_DEVICE | |
226 | default n | |
5474c120 | 227 | |
1da177e4 LT |
228 | config FB_MODE_HELPERS |
229 | bool "Enable Video Mode Handling Helpers" | |
230 | depends on FB | |
231 | default n | |
232 | ---help--- | |
233 | This enables functions for handling video modes using the | |
234 | Generalized Timing Formula and the EDID parser. A few drivers rely | |
235 | on this feature such as the radeonfb, rivafb, and the i810fb. If | |
236 | your driver does not take advantage of this feature, choosing Y will | |
237 | just increase the kernel size by about 5K. | |
238 | ||
239 | config FB_TILEBLITTING | |
240 | bool "Enable Tile Blitting Support" | |
241 | depends on FB | |
242 | default n | |
243 | ---help--- | |
244 | This enables tile blitting. Tile blitting is a drawing technique | |
245 | where the screen is divided into rectangular sections (tiles), whereas | |
246 | the standard blitting divides the screen into pixels. Because the | |
247 | default drawing element is a tile, drawing functions will be passed | |
248 | parameters in terms of number of tiles instead of number of pixels. | |
249 | For example, to draw a single character, instead of using bitmaps, | |
250 | an index to an array of bitmaps will be used. To clear or move a | |
251 | rectangular section of a screen, the rectangle will be described in | |
252 | terms of number of tiles in the x- and y-axis. | |
253 | ||
254 | This is particularly important to one driver, matroxfb. If | |
255 | unsure, say N. | |
256 | ||
10ccaf4b | 257 | comment "Frame buffer hardware drivers" |
e0e34ef7 JS |
258 | depends on FB |
259 | ||
a4b8f97a KG |
260 | config FB_GRVGA |
261 | tristate "Aeroflex Gaisler framebuffer support" | |
262 | depends on FB && SPARC | |
263 | select FB_CFB_FILLRECT | |
264 | select FB_CFB_COPYAREA | |
265 | select FB_CFB_IMAGEBLIT | |
266 | ---help--- | |
267 | This enables support for the SVGACTRL framebuffer in the GRLIB IP library from Aeroflex Gaisler. | |
268 | ||
1da177e4 LT |
269 | config FB_CIRRUS |
270 | tristate "Cirrus Logic support" | |
271 | depends on FB && (ZORRO || PCI) | |
272 | select FB_CFB_FILLRECT | |
273 | select FB_CFB_COPYAREA | |
274 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
275 | ---help--- |
276 | This enables support for Cirrus Logic GD542x/543x based boards on | |
277 | Amiga: SD64, Piccolo, Picasso II/II+, Picasso IV, or EGS Spectrum. | |
278 | ||
279 | If you have a PCI-based system, this enables support for these | |
280 | chips: GD-543x, GD-544x, GD-5480. | |
281 | ||
282 | Please read the file <file:Documentation/fb/cirrusfb.txt>. | |
283 | ||
284 | Say N unless you have such a graphics board or plan to get one | |
285 | before you next recompile the kernel. | |
286 | ||
287 | config FB_PM2 | |
288 | tristate "Permedia2 support" | |
289 | depends on FB && ((AMIGA && BROKEN) || PCI) | |
290 | select FB_CFB_FILLRECT | |
291 | select FB_CFB_COPYAREA | |
292 | select FB_CFB_IMAGEBLIT | |
1da177e4 | 293 | help |
4edad7f0 KH |
294 | This is the frame buffer device driver for cards based on |
295 | the 3D Labs Permedia, Permedia 2 and Permedia 2V chips. | |
296 | The driver was tested on the following cards: | |
297 | Diamond FireGL 1000 PRO AGP | |
298 | ELSA Gloria Synergy PCI | |
299 | Appian Jeronimo PRO (both heads) PCI | |
300 | 3DLabs Oxygen ACX aka EONtronics Picasso P2 PCI | |
301 | Techsource Raptor GFX-8P (aka Sun PGX-32) on SPARC | |
302 | ASK Graphic Blaster Exxtreme AGP | |
303 | ||
304 | To compile this driver as a module, choose M here: the | |
305 | module will be called pm2fb. | |
1da177e4 LT |
306 | |
307 | config FB_PM2_FIFO_DISCONNECT | |
308 | bool "enable FIFO disconnect feature" | |
309 | depends on FB_PM2 && PCI | |
310 | help | |
4edad7f0 | 311 | Support the Permedia2 FIFO disconnect feature. |
1da177e4 LT |
312 | |
313 | config FB_ARMCLCD | |
314 | tristate "ARM PrimeCell PL110 support" | |
c3235bfc MB |
315 | depends on ARM || ARM64 || COMPILE_TEST |
316 | depends on FB && ARM_AMBA | |
1da177e4 LT |
317 | select FB_CFB_FILLRECT |
318 | select FB_CFB_COPYAREA | |
319 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
320 | help |
321 | This framebuffer device driver is for the ARM PrimeCell PL110 | |
322 | Colour LCD controller. ARM PrimeCells provide the building | |
323 | blocks for System on a Chip devices. | |
324 | ||
325 | If you want to compile this as a module (=code which can be | |
326 | inserted into and removed from the running kernel), say M | |
39f5fb30 | 327 | here and read <file:Documentation/kbuild/modules.txt>. The module |
1da177e4 LT |
328 | will be called amba-clcd. |
329 | ||
330 | config FB_ACORN | |
331 | bool "Acorn VIDC support" | |
635f0258 | 332 | depends on (FB = y) && ARM && ARCH_ACORN |
1da177e4 LT |
333 | select FB_CFB_FILLRECT |
334 | select FB_CFB_COPYAREA | |
335 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
336 | help |
337 | This is the frame buffer device driver for the Acorn VIDC graphics | |
338 | hardware found in Acorn RISC PCs and other ARM-based machines. If | |
339 | unsure, say N. | |
340 | ||
341 | config FB_CLPS711X | |
342 | bool "CLPS711X LCD support" | |
343 | depends on (FB = y) && ARM && ARCH_CLPS711X | |
344 | select FB_CFB_FILLRECT | |
345 | select FB_CFB_COPYAREA | |
346 | select FB_CFB_IMAGEBLIT | |
e65c0850 RD |
347 | help |
348 | Say Y to enable the Framebuffer driver for the CLPS7111 and | |
349 | EP7212 processors. | |
1da177e4 LT |
350 | |
351 | config FB_SA1100 | |
352 | bool "SA-1100 LCD support" | |
353 | depends on (FB = y) && ARM && ARCH_SA1100 | |
354 | select FB_CFB_FILLRECT | |
355 | select FB_CFB_COPYAREA | |
356 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
357 | help |
358 | This is a framebuffer device for the SA-1100 LCD Controller. | |
359 | See <http://www.linux-fbdev.org/> for information on framebuffer | |
360 | devices. | |
361 | ||
362 | If you plan to use the LCD display with your SA-1100 system, say | |
363 | Y here. | |
364 | ||
7c2f891c | 365 | config FB_IMX |
d04d2681 | 366 | tristate "Freescale i.MX1/21/25/27 LCD support" |
f142b619 | 367 | depends on FB && IMX_HAVE_PLATFORM_IMX_FB |
7c2f891c SH |
368 | select FB_CFB_FILLRECT |
369 | select FB_CFB_COPYAREA | |
370 | select FB_CFB_IMAGEBLIT | |
1b6c7936 MP |
371 | select FB_MODE_HELPERS |
372 | select VIDEOMODE_HELPERS | |
7c2f891c | 373 | |
1da177e4 LT |
374 | config FB_CYBER2000 |
375 | tristate "CyberPro 2000/2010/5000 support" | |
376 | depends on FB && PCI && (BROKEN || !SPARC64) | |
377 | select FB_CFB_FILLRECT | |
378 | select FB_CFB_COPYAREA | |
379 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
380 | help |
381 | This enables support for the Integraphics CyberPro 20x0 and 5000 | |
382 | VGA chips used in the Rebel.com Netwinder and other machines. | |
383 | Say Y if you have a NetWinder or a graphics card containing this | |
384 | device, otherwise say N. | |
385 | ||
e5dedf8d OZ |
386 | config FB_CYBER2000_DDC |
387 | bool "DDC for CyberPro support" | |
388 | depends on FB_CYBER2000 | |
389 | select FB_DDC | |
390 | default y | |
391 | help | |
392 | Say Y here if you want DDC support for your CyberPro graphics | |
393 | card. This is only I2C bus support, driver does not use EDID. | |
394 | ||
b7ca01a9 RK |
395 | config FB_CYBER2000_I2C |
396 | bool "CyberPro 2000/2010/5000 I2C support" | |
397 | depends on FB_CYBER2000 && I2C && ARCH_NETWINDER | |
398 | select I2C_ALGOBIT | |
399 | help | |
400 | Enable support for the I2C video decoder interface on the | |
401 | Integraphics CyberPro 20x0 and 5000 VGA chips. This is used | |
402 | on the Netwinder machines for the SAA7111 video capture. | |
403 | ||
1da177e4 LT |
404 | config FB_APOLLO |
405 | bool | |
406 | depends on (FB = y) && APOLLO | |
407 | default y | |
408 | select FB_CFB_FILLRECT | |
409 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
410 | |
411 | config FB_Q40 | |
412 | bool | |
413 | depends on (FB = y) && Q40 | |
414 | default y | |
415 | select FB_CFB_FILLRECT | |
416 | select FB_CFB_COPYAREA | |
417 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
418 | |
419 | config FB_AMIGA | |
420 | tristate "Amiga native chipset support" | |
421 | depends on FB && AMIGA | |
1da177e4 LT |
422 | help |
423 | This is the frame buffer device driver for the builtin graphics | |
424 | chipset found in Amigas. | |
425 | ||
426 | To compile this driver as a module, choose M here: the | |
427 | module will be called amifb. | |
428 | ||
429 | config FB_AMIGA_OCS | |
430 | bool "Amiga OCS chipset support" | |
431 | depends on FB_AMIGA | |
432 | help | |
433 | This enables support for the original Agnus and Denise video chips, | |
434 | found in the Amiga 1000 and most A500's and A2000's. If you intend | |
435 | to run Linux on any of these systems, say Y; otherwise say N. | |
436 | ||
437 | config FB_AMIGA_ECS | |
438 | bool "Amiga ECS chipset support" | |
439 | depends on FB_AMIGA | |
440 | help | |
441 | This enables support for the Enhanced Chip Set, found in later | |
442 | A500's, later A2000's, the A600, the A3000, the A3000T and CDTV. If | |
443 | you intend to run Linux on any of these systems, say Y; otherwise | |
444 | say N. | |
445 | ||
446 | config FB_AMIGA_AGA | |
447 | bool "Amiga AGA chipset support" | |
448 | depends on FB_AMIGA | |
449 | help | |
450 | This enables support for the Advanced Graphics Architecture (also | |
451 | known as the AGA or AA) Chip Set, found in the A1200, A4000, A4000T | |
452 | and CD32. If you intend to run Linux on any of these systems, say Y; | |
453 | otherwise say N. | |
454 | ||
1da177e4 LT |
455 | config FB_FM2 |
456 | bool "Amiga FrameMaster II/Rainbow II support" | |
457 | depends on (FB = y) && ZORRO | |
458 | select FB_CFB_FILLRECT | |
459 | select FB_CFB_COPYAREA | |
460 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
461 | help |
462 | This is the frame buffer device driver for the Amiga FrameMaster | |
463 | card from BSC (exhibited 1992 but not shipped as a CBM product). | |
464 | ||
1154ea7d JK |
465 | config FB_ARC |
466 | tristate "Arc Monochrome LCD board support" | |
467 | depends on FB && X86 | |
922e6f9a AD |
468 | select FB_SYS_FILLRECT |
469 | select FB_SYS_COPYAREA | |
470 | select FB_SYS_IMAGEBLIT | |
d9a05f18 | 471 | select FB_SYS_FOPS |
1154ea7d JK |
472 | help |
473 | This enables support for the Arc Monochrome LCD board. The board | |
474 | is based on the KS-108 lcd controller and is typically a matrix | |
475 | of 2*n chips. This driver was tested with a 128x64 panel. This | |
476 | driver supports it for use with x86 SBCs through a 16 bit GPIO | |
09509603 | 477 | interface (8 bit data, 8 bit control). If you anticipate using |
1154ea7d JK |
478 | this driver, say Y or M; otherwise say N. You must specify the |
479 | GPIO IO address to be used for setting control and data. | |
480 | ||
1da177e4 LT |
481 | config FB_ATARI |
482 | bool "Atari native chipset support" | |
a1005012 MS |
483 | depends on (FB = y) && ATARI |
484 | select FB_CFB_FILLRECT | |
485 | select FB_CFB_COPYAREA | |
486 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
487 | help |
488 | This is the frame buffer device driver for the builtin graphics | |
489 | chipset found in Ataris. | |
490 | ||
491 | config FB_OF | |
492 | bool "Open Firmware frame buffer device support" | |
bed59275 | 493 | depends on (FB = y) && (PPC64 || PPC_OF) && (!PPC_PSERIES || PCI) |
1da177e4 LT |
494 | select FB_CFB_FILLRECT |
495 | select FB_CFB_COPYAREA | |
496 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
497 | select FB_MACMODES |
498 | help | |
499 | Say Y if you want support with Open Firmware for your graphics | |
500 | board. | |
501 | ||
502 | config FB_CONTROL | |
503 | bool "Apple \"control\" display support" | |
a04b61d3 | 504 | depends on (FB = y) && PPC_PMAC && PPC32 |
1da177e4 LT |
505 | select FB_CFB_FILLRECT |
506 | select FB_CFB_COPYAREA | |
507 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
508 | select FB_MACMODES |
509 | help | |
510 | This driver supports a frame buffer for the graphics adapter in the | |
511 | Power Macintosh 7300 and others. | |
512 | ||
513 | config FB_PLATINUM | |
514 | bool "Apple \"platinum\" display support" | |
a04b61d3 | 515 | depends on (FB = y) && PPC_PMAC && PPC32 |
1da177e4 LT |
516 | select FB_CFB_FILLRECT |
517 | select FB_CFB_COPYAREA | |
518 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
519 | select FB_MACMODES |
520 | help | |
521 | This driver supports a frame buffer for the "platinum" graphics | |
522 | adapter in some Power Macintoshes. | |
523 | ||
524 | config FB_VALKYRIE | |
525 | bool "Apple \"valkyrie\" display support" | |
a04b61d3 | 526 | depends on (FB = y) && (MAC || (PPC_PMAC && PPC32)) |
1da177e4 LT |
527 | select FB_CFB_FILLRECT |
528 | select FB_CFB_COPYAREA | |
529 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
530 | select FB_MACMODES |
531 | help | |
532 | This driver supports a frame buffer for the "valkyrie" graphics | |
533 | adapter in some Power Macintoshes. | |
534 | ||
535 | config FB_CT65550 | |
536 | bool "Chips 65550 display support" | |
0f8c0234 | 537 | depends on (FB = y) && PPC32 && PCI |
1da177e4 LT |
538 | select FB_CFB_FILLRECT |
539 | select FB_CFB_COPYAREA | |
540 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
541 | help |
542 | This is the frame buffer device driver for the Chips & Technologies | |
543 | 65550 graphics chip in PowerBooks. | |
544 | ||
545 | config FB_ASILIANT | |
e65c0850 | 546 | bool "Asiliant (Chips) 69000 display support" |
1da177e4 LT |
547 | depends on (FB = y) && PCI |
548 | select FB_CFB_FILLRECT | |
549 | select FB_CFB_COPYAREA | |
550 | select FB_CFB_IMAGEBLIT | |
4de0b1ee AD |
551 | help |
552 | This is the frame buffer device driver for the Asiliant 69030 chipset | |
1da177e4 LT |
553 | |
554 | config FB_IMSTT | |
555 | bool "IMS Twin Turbo display support" | |
556 | depends on (FB = y) && PCI | |
557 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
558 | select FB_MACMODES if PPC |
559 | help | |
560 | The IMS Twin Turbo is a PCI-based frame buffer card bundled with | |
561 | many Macintosh and compatible computers. | |
562 | ||
1da177e4 LT |
563 | config FB_VGA16 |
564 | tristate "VGA 16-color graphics support" | |
565 | depends on FB && (X86 || PPC) | |
566 | select FB_CFB_FILLRECT | |
567 | select FB_CFB_COPYAREA | |
568 | select FB_CFB_IMAGEBLIT | |
b2f594fd | 569 | select VGASTATE |
d60d2d8a | 570 | select FONT_8x16 if FRAMEBUFFER_CONSOLE |
1da177e4 LT |
571 | help |
572 | This is the frame buffer device driver for VGA 16 color graphic | |
573 | cards. Say Y if you have such a card. | |
574 | ||
575 | To compile this driver as a module, choose M here: the | |
576 | module will be called vga16fb. | |
577 | ||
e9fa7c43 MH |
578 | config FB_BF54X_LQ043 |
579 | tristate "SHARP LQ043 TFT LCD (BF548 EZKIT)" | |
e7a05aa9 | 580 | depends on FB && (BF54x) && !BF542 |
e9fa7c43 MH |
581 | select FB_CFB_FILLRECT |
582 | select FB_CFB_COPYAREA | |
583 | select FB_CFB_IMAGEBLIT | |
584 | help | |
585 | This is the framebuffer device driver for a SHARP LQ043T1DG01 TFT LCD | |
586 | ||
99eeed47 MH |
587 | config FB_BFIN_T350MCQB |
588 | tristate "Varitronix COG-T350MCQB TFT LCD display (BF527 EZKIT)" | |
589 | depends on FB && BLACKFIN | |
590 | select BFIN_GPTIMERS | |
591 | select FB_CFB_FILLRECT | |
592 | select FB_CFB_COPYAREA | |
593 | select FB_CFB_IMAGEBLIT | |
594 | help | |
595 | This is the framebuffer device driver for a Varitronix VL-PS-COG-T350MCQB-01 display TFT LCD | |
596 | This display is a QVGA 320x240 24-bit RGB display interfaced by an 8-bit wide PPI | |
597 | It uses PPI[0..7] PPI_FS1, PPI_FS2 and PPI_CLK. | |
598 | ||
9cfe4a93 MH |
599 | config FB_BFIN_LQ035Q1 |
600 | tristate "SHARP LQ035Q1DH02 TFT LCD" | |
601 | depends on FB && BLACKFIN && SPI | |
602 | select FB_CFB_FILLRECT | |
603 | select FB_CFB_COPYAREA | |
604 | select FB_CFB_IMAGEBLIT | |
605 | select BFIN_GPTIMERS | |
606 | help | |
607 | This is the framebuffer device driver for a SHARP LQ035Q1DH02 TFT display found on | |
608 | the Blackfin Landscape LCD EZ-Extender Card. | |
609 | This display is a QVGA 320x240 18-bit RGB display interfaced by an 16-bit wide PPI | |
610 | It uses PPI[0..15] PPI_FS1, PPI_FS2 and PPI_CLK. | |
611 | ||
612 | To compile this driver as a module, choose M here: the | |
613 | module will be called bfin-lq035q1-fb. | |
99eeed47 | 614 | |
dbcc465a MH |
615 | config FB_BF537_LQ035 |
616 | tristate "SHARP LQ035 TFT LCD (BF537 STAMP)" | |
617 | depends on FB && (BF534 || BF536 || BF537) && I2C_BLACKFIN_TWI | |
618 | select FB_CFB_FILLRECT | |
619 | select FB_CFB_COPYAREA | |
620 | select FB_CFB_IMAGEBLIT | |
621 | select BFIN_GPTIMERS | |
622 | help | |
623 | This is the framebuffer device for a SHARP LQ035Q7DB03 TFT LCD | |
624 | attached to a BF537. | |
625 | ||
626 | To compile this driver as a module, choose M here: the | |
627 | module will be called bf537-lq035. | |
628 | ||
cffd9348 MH |
629 | config FB_BFIN_7393 |
630 | tristate "Blackfin ADV7393 Video encoder" | |
631 | depends on FB && BLACKFIN | |
632 | select I2C | |
633 | select FB_CFB_FILLRECT | |
634 | select FB_CFB_COPYAREA | |
635 | select FB_CFB_IMAGEBLIT | |
636 | help | |
637 | This is the framebuffer device for a ADV7393 video encoder | |
638 | attached to a Blackfin on the PPI port. | |
639 | If your Blackfin board has a ADV7393 select Y. | |
640 | ||
641 | To compile this driver as a module, choose M here: the | |
642 | module will be called bfin_adv7393fb. | |
643 | ||
644 | choice | |
645 | prompt "Video mode support" | |
646 | depends on FB_BFIN_7393 | |
647 | default NTSC | |
648 | ||
649 | config NTSC | |
650 | bool 'NTSC 720x480' | |
651 | ||
652 | config PAL | |
653 | bool 'PAL 720x576' | |
654 | ||
655 | config NTSC_640x480 | |
656 | bool 'NTSC 640x480 (Experimental)' | |
657 | ||
658 | config PAL_640x480 | |
659 | bool 'PAL 640x480 (Experimental)' | |
660 | ||
661 | config NTSC_YCBCR | |
662 | bool 'NTSC 720x480 YCbCR input' | |
663 | ||
664 | config PAL_YCBCR | |
665 | bool 'PAL 720x576 YCbCR input' | |
666 | ||
667 | endchoice | |
668 | ||
669 | choice | |
670 | prompt "Size of ADV7393 frame buffer memory Single/Double Size" | |
671 | depends on (FB_BFIN_7393) | |
672 | default ADV7393_1XMEM | |
673 | ||
674 | config ADV7393_1XMEM | |
675 | bool 'Single' | |
676 | ||
677 | config ADV7393_2XMEM | |
678 | bool 'Double' | |
679 | endchoice | |
680 | ||
1da177e4 LT |
681 | config FB_STI |
682 | tristate "HP STI frame buffer device support" | |
683 | depends on FB && PARISC | |
684 | select FB_CFB_FILLRECT | |
685 | select FB_CFB_COPYAREA | |
686 | select FB_CFB_IMAGEBLIT | |
17085a93 AB |
687 | select STI_CONSOLE |
688 | select VT | |
1da177e4 LT |
689 | default y |
690 | ---help--- | |
691 | STI refers to the HP "Standard Text Interface" which is a set of | |
692 | BIOS routines contained in a ROM chip in HP PA-RISC based machines. | |
693 | Enabling this option will implement the linux framebuffer device | |
694 | using calls to the STI BIOS routines for initialisation. | |
695 | ||
696 | If you enable this option, you will get a planar framebuffer device | |
697 | /dev/fb which will work on the most common HP graphic cards of the | |
698 | NGLE family, including the artist chips (in the 7xx and Bxxx series), | |
699 | HCRX, HCRX24, CRX, CRX24 and VisEG series. | |
700 | ||
701 | It is safe to enable this option, so you should probably say "Y". | |
702 | ||
703 | config FB_MAC | |
704 | bool "Generic Macintosh display support" | |
705 | depends on (FB = y) && MAC | |
706 | select FB_CFB_FILLRECT | |
707 | select FB_CFB_COPYAREA | |
708 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
709 | select FB_MACMODES |
710 | ||
1da177e4 LT |
711 | config FB_HP300 |
712 | bool | |
ad7e484f | 713 | depends on (FB = y) && DIO |
1da177e4 | 714 | select FB_CFB_IMAGEBLIT |
1da177e4 LT |
715 | default y |
716 | ||
717 | config FB_TGA | |
86c6f7d0 MR |
718 | tristate "TGA/SFB+ framebuffer support" |
719 | depends on FB && (ALPHA || TC) | |
1da177e4 LT |
720 | select FB_CFB_FILLRECT |
721 | select FB_CFB_COPYAREA | |
722 | select FB_CFB_IMAGEBLIT | |
1c667682 | 723 | select BITREVERSE |
86c6f7d0 MR |
724 | ---help--- |
725 | This is the frame buffer device driver for generic TGA and SFB+ | |
726 | graphic cards. These include DEC ZLXp-E1, -E2 and -E3 PCI cards, | |
727 | also known as PBXGA-A, -B and -C, and DEC ZLX-E1, -E2 and -E3 | |
728 | TURBOchannel cards, also known as PMAGD-A, -B and -C. | |
729 | ||
730 | Due to hardware limitations ZLX-E2 and E3 cards are not supported | |
731 | for DECstation 5000/200 systems. Additionally due to firmware | |
732 | limitations these cards may cause troubles with booting DECstation | |
733 | 5000/240 and /260 systems, but are fully supported under Linux if | |
734 | you manage to get it going. ;-) | |
735 | ||
736 | Say Y if you have one of those. | |
1da177e4 | 737 | |
8bdb3a2d MJ |
738 | config FB_UVESA |
739 | tristate "Userspace VESA VGA graphics support" | |
740 | depends on FB && CONNECTOR | |
741 | select FB_CFB_FILLRECT | |
742 | select FB_CFB_COPYAREA | |
743 | select FB_CFB_IMAGEBLIT | |
744 | select FB_MODE_HELPERS | |
745 | help | |
746 | This is the frame buffer driver for generic VBE 2.0 compliant | |
747 | graphic cards. It can also take advantage of VBE 3.0 features, | |
748 | such as refresh rate adjustment. | |
749 | ||
750 | This driver generally provides more features than vesafb but | |
751 | requires a userspace helper application called 'v86d'. See | |
752 | <file:Documentation/fb/uvesafb.txt> for more information. | |
753 | ||
754 | If unsure, say N. | |
755 | ||
1da177e4 LT |
756 | config FB_VESA |
757 | bool "VESA VGA graphics support" | |
0d078f6f | 758 | depends on (FB = y) && X86 |
1da177e4 LT |
759 | select FB_CFB_FILLRECT |
760 | select FB_CFB_COPYAREA | |
761 | select FB_CFB_IMAGEBLIT | |
4d31a2b7 | 762 | select FB_BOOT_VESA_SUPPORT |
1da177e4 LT |
763 | help |
764 | This is the frame buffer device driver for generic VESA 2.0 | |
765 | compliant graphic cards. The older VESA 1.2 cards are not supported. | |
766 | You will get a boot time penguin logo at no additional cost. Please | |
767 | read <file:Documentation/fb/vesafb.txt>. If unsure, say Y. | |
768 | ||
7c83172b HY |
769 | config FB_EFI |
770 | bool "EFI-based Framebuffer Support" | |
b64ef8af | 771 | depends on (FB = y) && X86 && EFI |
90b4f9ac EH |
772 | select FB_CFB_FILLRECT |
773 | select FB_CFB_COPYAREA | |
774 | select FB_CFB_IMAGEBLIT | |
775 | help | |
7c08c9ae PJ |
776 | This is the EFI frame buffer device driver. If the firmware on |
777 | your platform is EFI 1.10 or UEFI 2.0, select Y to add support for | |
778 | using the EFI framebuffer as your console. | |
90b4f9ac | 779 | |
0e27aa3d JK |
780 | config FB_N411 |
781 | tristate "N411 Apollo/Hecuba devkit support" | |
aad09e51 | 782 | depends on FB && X86 && MMU |
d6774935 AD |
783 | select FB_SYS_FILLRECT |
784 | select FB_SYS_COPYAREA | |
785 | select FB_SYS_IMAGEBLIT | |
28d4564b | 786 | select FB_SYS_FOPS |
aad09e51 | 787 | select FB_DEFERRED_IO |
0e27aa3d | 788 | select FB_HECUBA |
aad09e51 | 789 | help |
0e27aa3d JK |
790 | This enables support for the Apollo display controller in its |
791 | Hecuba form using the n411 devkit. | |
aad09e51 | 792 | |
1da177e4 LT |
793 | config FB_HGA |
794 | tristate "Hercules mono graphics support" | |
795 | depends on FB && X86 | |
1da177e4 LT |
796 | help |
797 | Say Y here if you have a Hercules mono graphics card. | |
798 | ||
799 | To compile this driver as a module, choose M here: the | |
800 | module will be called hgafb. | |
801 | ||
529ed806 BC |
802 | As this card technology is at least 25 years old, |
803 | most people will answer N here. | |
1da177e4 | 804 | |
1da177e4 LT |
805 | config FB_SGIVW |
806 | tristate "SGI Visual Workstation framebuffer support" | |
807 | depends on FB && X86_VISWS | |
808 | select FB_CFB_FILLRECT | |
809 | select FB_CFB_COPYAREA | |
810 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
811 | help |
812 | SGI Visual Workstation support for framebuffer graphics. | |
813 | ||
814 | config FB_GBE | |
815 | bool "SGI Graphics Backend frame buffer support" | |
816 | depends on (FB = y) && (SGI_IP32 || X86_VISWS) | |
817 | select FB_CFB_FILLRECT | |
818 | select FB_CFB_COPYAREA | |
819 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
820 | help |
821 | This is the frame buffer device driver for SGI Graphics Backend. | |
822 | This chip is used in SGI O2 and Visual Workstation 320/540. | |
823 | ||
824 | config FB_GBE_MEM | |
825 | int "Video memory size in MB" | |
826 | depends on FB_GBE | |
80c410dc | 827 | default 4 |
1da177e4 LT |
828 | help |
829 | This is the amount of memory reserved for the framebuffer, | |
830 | which can be any value between 1MB and 8MB. | |
831 | ||
1a571986 MF |
832 | config FB_SBUS |
833 | bool "SBUS and UPA framebuffers" | |
0b57ee9e | 834 | depends on (FB = y) && SPARC |
1a571986 MF |
835 | help |
836 | Say Y if you want support for SBUS or UPA based frame buffer device. | |
837 | ||
1da177e4 LT |
838 | config FB_BW2 |
839 | bool "BWtwo support" | |
e019630e | 840 | depends on (FB = y) && (SPARC && FB_SBUS) |
1da177e4 LT |
841 | select FB_CFB_FILLRECT |
842 | select FB_CFB_COPYAREA | |
843 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
844 | help |
845 | This is the frame buffer device driver for the BWtwo frame buffer. | |
846 | ||
847 | config FB_CG3 | |
848 | bool "CGthree support" | |
e019630e | 849 | depends on (FB = y) && (SPARC && FB_SBUS) |
1a571986 | 850 | select FB_CFB_FILLRECT |
1da177e4 LT |
851 | select FB_CFB_COPYAREA |
852 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
853 | help |
854 | This is the frame buffer device driver for the CGthree frame buffer. | |
855 | ||
856 | config FB_CG6 | |
857 | bool "CGsix (GX,TurboGX) support" | |
e019630e | 858 | depends on (FB = y) && (SPARC && FB_SBUS) |
1da177e4 LT |
859 | select FB_CFB_COPYAREA |
860 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
861 | help |
862 | This is the frame buffer device driver for the CGsix (GX, TurboGX) | |
863 | frame buffer. | |
864 | ||
8d74c1fd KH |
865 | config FB_FFB |
866 | bool "Creator/Creator3D/Elite3D support" | |
867 | depends on FB_SBUS && SPARC64 | |
868 | select FB_CFB_COPYAREA | |
869 | select FB_CFB_IMAGEBLIT | |
870 | help | |
871 | This is the frame buffer device driver for the Creator, Creator3D, | |
872 | and Elite3D graphics boards. | |
873 | ||
874 | config FB_TCX | |
875 | bool "TCX (SS4/SS5 only) support" | |
876 | depends on FB_SBUS | |
877 | select FB_CFB_FILLRECT | |
878 | select FB_CFB_COPYAREA | |
879 | select FB_CFB_IMAGEBLIT | |
880 | help | |
881 | This is the frame buffer device driver for the TCX 24/8bit frame | |
882 | buffer. | |
883 | ||
884 | config FB_CG14 | |
885 | bool "CGfourteen (SX) support" | |
886 | depends on FB_SBUS | |
887 | select FB_CFB_FILLRECT | |
888 | select FB_CFB_COPYAREA | |
889 | select FB_CFB_IMAGEBLIT | |
890 | help | |
891 | This is the frame buffer device driver for the CGfourteen frame | |
892 | buffer on Desktop SPARCsystems with the SX graphics option. | |
893 | ||
894 | config FB_P9100 | |
895 | bool "P9100 (Sparcbook 3 only) support" | |
896 | depends on FB_SBUS | |
897 | select FB_CFB_FILLRECT | |
898 | select FB_CFB_COPYAREA | |
899 | select FB_CFB_IMAGEBLIT | |
900 | help | |
901 | This is the frame buffer device driver for the P9100 card | |
902 | supported on Sparcbook 3 machines. | |
903 | ||
904 | config FB_LEO | |
905 | bool "Leo (ZX) support" | |
906 | depends on FB_SBUS | |
907 | select FB_CFB_FILLRECT | |
908 | select FB_CFB_COPYAREA | |
909 | select FB_CFB_IMAGEBLIT | |
910 | help | |
911 | This is the frame buffer device driver for the SBUS-based Sun ZX | |
912 | (leo) frame buffer cards. | |
913 | ||
914 | config FB_IGA | |
915 | bool "IGA 168x display support" | |
e11a6c23 | 916 | depends on (FB = y) && SPARC32 |
8d74c1fd KH |
917 | select FB_CFB_FILLRECT |
918 | select FB_CFB_COPYAREA | |
919 | select FB_CFB_IMAGEBLIT | |
920 | help | |
921 | This is the framebuffer device for the INTERGRAPHICS 1680 and | |
922 | successor frame buffer cards. | |
923 | ||
924 | config FB_XVR500 | |
925 | bool "Sun XVR-500 3DLABS Wildcat support" | |
e11a6c23 | 926 | depends on (FB = y) && PCI && SPARC64 |
8d74c1fd KH |
927 | select FB_CFB_FILLRECT |
928 | select FB_CFB_COPYAREA | |
929 | select FB_CFB_IMAGEBLIT | |
930 | help | |
931 | This is the framebuffer device for the Sun XVR-500 and similar | |
932 | graphics cards based upon the 3DLABS Wildcat chipset. The driver | |
01dd2fbf | 933 | only works on sparc64 systems where the system firmware has |
8d74c1fd KH |
934 | mostly initialized the card already. It is treated as a |
935 | completely dumb framebuffer device. | |
936 | ||
937 | config FB_XVR2500 | |
938 | bool "Sun XVR-2500 3DLABS Wildcat support" | |
e11a6c23 | 939 | depends on (FB = y) && PCI && SPARC64 |
8d74c1fd KH |
940 | select FB_CFB_FILLRECT |
941 | select FB_CFB_COPYAREA | |
942 | select FB_CFB_IMAGEBLIT | |
943 | help | |
944 | This is the framebuffer device for the Sun XVR-2500 and similar | |
945 | graphics cards based upon the 3DLABS Wildcat chipset. The driver | |
01dd2fbf | 946 | only works on sparc64 systems where the system firmware has |
8d74c1fd KH |
947 | mostly initialized the card already. It is treated as a |
948 | completely dumb framebuffer device. | |
949 | ||
2d378b91 DM |
950 | config FB_XVR1000 |
951 | bool "Sun XVR-1000 support" | |
f04e879b | 952 | depends on (FB = y) && SPARC64 |
2d378b91 DM |
953 | select FB_CFB_FILLRECT |
954 | select FB_CFB_COPYAREA | |
955 | select FB_CFB_IMAGEBLIT | |
956 | help | |
957 | This is the framebuffer device for the Sun XVR-1000 and similar | |
958 | graphics cards. The driver only works on sparc64 systems where | |
959 | the system firmware has mostly initialized the card already. It | |
960 | is treated as a completely dumb framebuffer device. | |
961 | ||
1da177e4 LT |
962 | config FB_PVR2 |
963 | tristate "NEC PowerVR 2 display support" | |
964 | depends on FB && SH_DREAMCAST | |
965 | select FB_CFB_FILLRECT | |
966 | select FB_CFB_COPYAREA | |
967 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
968 | ---help--- |
969 | Say Y here if you have a PowerVR 2 card in your box. If you plan to | |
970 | run linux on your Dreamcast, you will have to say Y here. | |
971 | This driver may or may not work on other PowerVR 2 cards, but is | |
972 | totally untested. Use at your own risk. If unsure, say N. | |
973 | ||
974 | To compile this driver as a module, choose M here: the | |
975 | module will be called pvr2fb. | |
976 | ||
977 | You can pass several parameters to the driver at boot time or at | |
978 | module load time. The parameters look like "video=pvr2:XXX", where | |
979 | the meaning of XXX can be found at the end of the main source file | |
980 | (<file:drivers/video/pvr2fb.c>). Please see the file | |
981 | <file:Documentation/fb/pvr2fb.txt>. | |
982 | ||
e61d05dd SK |
983 | config FB_OPENCORES |
984 | tristate "OpenCores VGA/LCD core 2.0 framebuffer support" | |
985 | depends on FB | |
986 | select FB_CFB_FILLRECT | |
987 | select FB_CFB_COPYAREA | |
988 | select FB_CFB_IMAGEBLIT | |
989 | help | |
990 | This enables support for the OpenCores VGA/LCD core. | |
991 | ||
992 | The OpenCores VGA/LCD core is typically used together with | |
993 | softcore CPUs (e.g. OpenRISC or Microblaze) or hard processor | |
994 | systems (e.g. Altera socfpga or Xilinx Zynq) on FPGAs. | |
995 | ||
996 | The source code and specification for the core is available at | |
997 | <http://opencores.org/project,vga_lcd> | |
998 | ||
ecc41d5e RD |
999 | config FB_S1D13XXX |
1000 | tristate "Epson S1D13XXX framebuffer support" | |
1001 | depends on FB | |
1002 | select FB_CFB_FILLRECT | |
1003 | select FB_CFB_COPYAREA | |
1004 | select FB_CFB_IMAGEBLIT | |
ecc41d5e RD |
1005 | help |
1006 | Support for S1D13XXX framebuffer device family (currently only | |
1007 | working with S1D13806). Product specs at | |
631dd1a8 | 1008 | <http://vdc.epson.com/> |
ecc41d5e | 1009 | |
14340586 NF |
1010 | config FB_ATMEL |
1011 | tristate "AT91/AT32 LCD Controller support" | |
0912e535 | 1012 | depends on FB && HAVE_FB_ATMEL |
14340586 NF |
1013 | select FB_CFB_FILLRECT |
1014 | select FB_CFB_COPYAREA | |
1015 | select FB_CFB_IMAGEBLIT | |
b985172b JCPV |
1016 | select FB_MODE_HELPERS |
1017 | select VIDEOMODE_HELPERS | |
14340586 NF |
1018 | help |
1019 | This enables support for the AT91/AT32 LCD Controller. | |
1020 | ||
1021 | config FB_INTSRAM | |
1022 | bool "Frame Buffer in internal SRAM" | |
1023 | depends on FB_ATMEL && ARCH_AT91SAM9261 | |
1024 | help | |
1025 | Say Y if you want to map Frame Buffer in internal SRAM. Say N if you want | |
1026 | to let frame buffer in external SDRAM. | |
1027 | ||
250a269d NF |
1028 | config FB_ATMEL_STN |
1029 | bool "Use a STN display with AT91/AT32 LCD Controller" | |
915190f7 | 1030 | depends on FB_ATMEL && (MACH_AT91SAM9261EK || MACH_AT91SAM9G10EK) |
250a269d NF |
1031 | default n |
1032 | help | |
1033 | Say Y if you want to connect a STN LCD display to the AT91/AT32 LCD | |
1034 | Controller. Say N if you want to connect a TFT. | |
1035 | ||
1036 | If unsure, say N. | |
1037 | ||
1da177e4 LT |
1038 | config FB_NVIDIA |
1039 | tristate "nVidia Framebuffer Support" | |
1040 | depends on FB && PCI | |
e0e34ef7 | 1041 | select FB_BACKLIGHT if FB_NVIDIA_BACKLIGHT |
1da177e4 LT |
1042 | select FB_MODE_HELPERS |
1043 | select FB_CFB_FILLRECT | |
1044 | select FB_CFB_COPYAREA | |
1045 | select FB_CFB_IMAGEBLIT | |
1c667682 | 1046 | select BITREVERSE |
b2f594fd | 1047 | select VGASTATE |
1da177e4 LT |
1048 | help |
1049 | This driver supports graphics boards with the nVidia chips, TNT | |
1050 | and newer. For very old chipsets, such as the RIVA128, then use | |
1051 | the rivafb. | |
1052 | Say Y if you have such a graphics board. | |
1053 | ||
1054 | To compile this driver as a module, choose M here: the | |
1055 | module will be called nvidiafb. | |
1056 | ||
1057 | config FB_NVIDIA_I2C | |
1058 | bool "Enable DDC Support" | |
85f1503a | 1059 | depends on FB_NVIDIA |
166f60dd | 1060 | select FB_DDC |
1da177e4 LT |
1061 | help |
1062 | This enables I2C support for nVidia Chipsets. This is used | |
1063 | only for getting EDID information from the attached display | |
1064 | allowing for robust video mode handling and switching. | |
1065 | ||
1066 | Because fbdev-2.6 requires that drivers must be able to | |
1067 | independently validate video mode parameters, you should say Y | |
1068 | here. | |
1069 | ||
647f2e7a JD |
1070 | config FB_NVIDIA_DEBUG |
1071 | bool "Lots of debug output" | |
1072 | depends on FB_NVIDIA | |
1073 | default n | |
1074 | help | |
1075 | Say Y here if you want the nVidia driver to output all sorts | |
1076 | of debugging information to provide to the maintainer when | |
1077 | something goes wrong. | |
1078 | ||
5474c120 MH |
1079 | config FB_NVIDIA_BACKLIGHT |
1080 | bool "Support for backlight control" | |
e0e34ef7 | 1081 | depends on FB_NVIDIA |
5474c120 MH |
1082 | default y |
1083 | help | |
1084 | Say Y here if you want to control the backlight of your display. | |
1085 | ||
1da177e4 LT |
1086 | config FB_RIVA |
1087 | tristate "nVidia Riva support" | |
1088 | depends on FB && PCI | |
e0e34ef7 | 1089 | select FB_BACKLIGHT if FB_RIVA_BACKLIGHT |
1da177e4 LT |
1090 | select FB_MODE_HELPERS |
1091 | select FB_CFB_FILLRECT | |
1092 | select FB_CFB_COPYAREA | |
1093 | select FB_CFB_IMAGEBLIT | |
1c667682 | 1094 | select BITREVERSE |
b2f594fd | 1095 | select VGASTATE |
1da177e4 LT |
1096 | help |
1097 | This driver supports graphics boards with the nVidia Riva/Geforce | |
1098 | chips. | |
1099 | Say Y if you have such a graphics board. | |
1100 | ||
1101 | To compile this driver as a module, choose M here: the | |
1102 | module will be called rivafb. | |
1103 | ||
1104 | config FB_RIVA_I2C | |
1105 | bool "Enable DDC Support" | |
1106 | depends on FB_RIVA | |
166f60dd | 1107 | select FB_DDC |
1da177e4 LT |
1108 | help |
1109 | This enables I2C support for nVidia Chipsets. This is used | |
1110 | only for getting EDID information from the attached display | |
1111 | allowing for robust video mode handling and switching. | |
1112 | ||
1113 | Because fbdev-2.6 requires that drivers must be able to | |
1114 | independently validate video mode parameters, you should say Y | |
1115 | here. | |
1116 | ||
1117 | config FB_RIVA_DEBUG | |
647f2e7a | 1118 | bool "Lots of debug output" |
1da177e4 LT |
1119 | depends on FB_RIVA |
1120 | default n | |
1121 | help | |
1122 | Say Y here if you want the Riva driver to output all sorts | |
09509603 | 1123 | of debugging information to provide to the maintainer when |
1da177e4 LT |
1124 | something goes wrong. |
1125 | ||
5474c120 MH |
1126 | config FB_RIVA_BACKLIGHT |
1127 | bool "Support for backlight control" | |
e0e34ef7 | 1128 | depends on FB_RIVA |
5474c120 MH |
1129 | default y |
1130 | help | |
1131 | Say Y here if you want to control the backlight of your display. | |
1132 | ||
5350c65f | 1133 | config FB_I740 |
d1d34224 KC |
1134 | tristate "Intel740 support" |
1135 | depends on FB && PCI | |
5350c65f OZ |
1136 | select FB_MODE_HELPERS |
1137 | select FB_CFB_FILLRECT | |
1138 | select FB_CFB_COPYAREA | |
1139 | select FB_CFB_IMAGEBLIT | |
1140 | select VGASTATE | |
1141 | select FB_DDC | |
1142 | help | |
1143 | This driver supports graphics cards based on Intel740 chip. | |
1144 | ||
1da177e4 | 1145 | config FB_I810 |
d1d34224 KC |
1146 | tristate "Intel 810/815 support" |
1147 | depends on FB && PCI && X86_32 && AGP_INTEL | |
1da177e4 LT |
1148 | select FB_MODE_HELPERS |
1149 | select FB_CFB_FILLRECT | |
1150 | select FB_CFB_COPYAREA | |
1151 | select FB_CFB_IMAGEBLIT | |
b2f594fd | 1152 | select VGASTATE |
1da177e4 LT |
1153 | help |
1154 | This driver supports the on-board graphics built in to the Intel 810 | |
1155 | and 815 chipsets. Say Y if you have and plan to use such a board. | |
1156 | ||
1157 | To compile this driver as a module, choose M here: the | |
1158 | module will be called i810fb. | |
1159 | ||
1160 | For more information, please read | |
1161 | <file:Documentation/fb/intel810.txt> | |
1162 | ||
1163 | config FB_I810_GTF | |
1164 | bool "use VESA Generalized Timing Formula" | |
1165 | depends on FB_I810 | |
1166 | help | |
1167 | If you say Y, then the VESA standard, Generalized Timing Formula | |
1168 | or GTF, will be used to calculate the required video timing values | |
1169 | per video mode. Since the GTF allows nondiscrete timings | |
1170 | (nondiscrete being a range of values as opposed to discrete being a | |
1171 | set of values), you'll be able to use any combination of horizontal | |
1172 | and vertical resolutions, and vertical refresh rates without having | |
1173 | to specify your own timing parameters. This is especially useful | |
1174 | to maximize the performance of an aging display, or if you just | |
1175 | have a display with nonstandard dimensions. A VESA compliant | |
1176 | monitor is recommended, but can still work with non-compliant ones. | |
1177 | If you need or want this, then select this option. The timings may | |
1178 | not be compliant with Intel's recommended values. Use at your own | |
1179 | risk. | |
1180 | ||
1181 | If you say N, the driver will revert to discrete video timings | |
1182 | using a set recommended by Intel in their documentation. | |
1183 | ||
1184 | If unsure, say N. | |
1185 | ||
74f6ae84 AD |
1186 | config FB_I810_I2C |
1187 | bool "Enable DDC Support" | |
db84502b | 1188 | depends on FB_I810 && FB_I810_GTF |
e80987f8 | 1189 | select FB_DDC |
74f6ae84 AD |
1190 | help |
1191 | ||
dbe7e429 AH |
1192 | config FB_LE80578 |
1193 | tristate "Intel LE80578 (Vermilion) support" | |
1194 | depends on FB && PCI && X86 | |
1195 | select FB_MODE_HELPERS | |
1196 | select FB_CFB_FILLRECT | |
1197 | select FB_CFB_COPYAREA | |
1198 | select FB_CFB_IMAGEBLIT | |
1199 | help | |
1200 | This driver supports the LE80578 (Vermilion Range) chipset | |
1201 | ||
1202 | config FB_CARILLO_RANCH | |
1203 | tristate "Intel Carillo Ranch support" | |
1204 | depends on FB_LE80578 && FB && PCI && X86 | |
1205 | help | |
1206 | This driver supports the LE80578 (Carillo Ranch) board | |
1207 | ||
1da177e4 | 1208 | config FB_INTEL |
d1d34224 KC |
1209 | tristate "Intel 830M/845G/852GM/855GM/865G/915G/945G/945GM/965G/965GM support" |
1210 | depends on FB && PCI && X86 && AGP_INTEL && EXPERT | |
1da177e4 LT |
1211 | select FB_MODE_HELPERS |
1212 | select FB_CFB_FILLRECT | |
1213 | select FB_CFB_COPYAREA | |
1214 | select FB_CFB_IMAGEBLIT | |
4b198289 | 1215 | select FB_BOOT_VESA_SUPPORT if FB_INTEL = y |
ba0ab823 | 1216 | depends on !DRM_I915 |
1da177e4 LT |
1217 | help |
1218 | This driver supports the on-board graphics built in to the Intel | |
0e170c72 | 1219 | 830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM/965G/965GM chipsets. |
1da177e4 LT |
1220 | Say Y if you have and plan to use such a board. |
1221 | ||
4b198289 KH |
1222 | To make FB_INTELFB=Y work you need to say AGP_INTEL=y too. |
1223 | ||
1f6e8449 | 1224 | To compile this driver as a module, choose M here: the |
1da177e4 LT |
1225 | module will be called intelfb. |
1226 | ||
d463d34e CM |
1227 | For more information, please read <file:Documentation/fb/intelfb.txt> |
1228 | ||
1da177e4 | 1229 | config FB_INTEL_DEBUG |
1f6e8449 | 1230 | bool "Intel driver Debug Messages" |
1da177e4 LT |
1231 | depends on FB_INTEL |
1232 | ---help--- | |
1233 | Say Y here if you want the Intel driver to output all sorts | |
09509603 | 1234 | of debugging information to provide to the maintainer when |
1da177e4 LT |
1235 | something goes wrong. |
1236 | ||
1f6e8449 DM |
1237 | config FB_INTEL_I2C |
1238 | bool "DDC/I2C for Intel framebuffer support" | |
1239 | depends on FB_INTEL | |
166f60dd | 1240 | select FB_DDC |
1f6e8449 DM |
1241 | default y |
1242 | help | |
1243 | Say Y here if you want DDC/I2C support for your on-board Intel graphics. | |
1244 | ||
1da177e4 LT |
1245 | config FB_MATROX |
1246 | tristate "Matrox acceleration" | |
1247 | depends on FB && PCI | |
1248 | select FB_CFB_FILLRECT | |
1249 | select FB_CFB_COPYAREA | |
1250 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
1251 | select FB_TILEBLITTING |
1252 | select FB_MACMODES if PPC_PMAC | |
1253 | ---help--- | |
1254 | Say Y here if you have a Matrox Millennium, Matrox Millennium II, | |
1255 | Matrox Mystique, Matrox Mystique 220, Matrox Productiva G100, Matrox | |
1256 | Mystique G200, Matrox Millennium G200, Matrox Marvel G200 video, | |
1257 | Matrox G400, G450 or G550 card in your box. | |
1258 | ||
1259 | To compile this driver as a module, choose M here: the | |
1260 | module will be called matroxfb. | |
1261 | ||
1262 | You can pass several parameters to the driver at boot time or at | |
90a48151 | 1263 | module load time. The parameters look like "video=matroxfb:XXX", and |
1da177e4 LT |
1264 | are described in <file:Documentation/fb/matroxfb.txt>. |
1265 | ||
1266 | config FB_MATROX_MILLENIUM | |
1267 | bool "Millennium I/II support" | |
1268 | depends on FB_MATROX | |
1269 | help | |
1270 | Say Y here if you have a Matrox Millennium or Matrox Millennium II | |
1271 | video card. If you select "Advanced lowlevel driver options" below, | |
1272 | you should check 4 bpp packed pixel, 8 bpp packed pixel, 16 bpp | |
1273 | packed pixel, 24 bpp packed pixel and 32 bpp packed pixel. You can | |
1274 | also use font widths different from 8. | |
1275 | ||
1276 | config FB_MATROX_MYSTIQUE | |
1277 | bool "Mystique support" | |
1278 | depends on FB_MATROX | |
1279 | help | |
1280 | Say Y here if you have a Matrox Mystique or Matrox Mystique 220 | |
1281 | video card. If you select "Advanced lowlevel driver options" below, | |
1282 | you should check 8 bpp packed pixel, 16 bpp packed pixel, 24 bpp | |
1283 | packed pixel and 32 bpp packed pixel. You can also use font widths | |
1284 | different from 8. | |
1285 | ||
1286 | config FB_MATROX_G | |
1287 | bool "G100/G200/G400/G450/G550 support" | |
1288 | depends on FB_MATROX | |
1289 | ---help--- | |
1290 | Say Y here if you have a Matrox G100, G200, G400, G450 or G550 based | |
1291 | video card. If you select "Advanced lowlevel driver options", you | |
1292 | should check 8 bpp packed pixel, 16 bpp packed pixel, 24 bpp packed | |
1293 | pixel and 32 bpp packed pixel. You can also use font widths | |
1294 | different from 8. | |
1295 | ||
ee83126b JD |
1296 | If you need support for G400 secondary head, you must say Y to |
1297 | "Matrox I2C support" and "G400 second head support" right below. | |
1298 | G450/G550 secondary head and digital output are supported without | |
1299 | additional modules. | |
1da177e4 LT |
1300 | |
1301 | The driver starts in monitor mode. You must use the matroxset tool | |
1302 | (available at <ftp://platan.vc.cvut.cz/pub/linux/matrox-latest/>) to | |
1303 | swap primary and secondary head outputs, or to change output mode. | |
1304 | Secondary head driver always start in 640x480 resolution and you | |
1305 | must use fbset to change it. | |
1306 | ||
1307 | Do not forget that second head supports only 16 and 32 bpp | |
1308 | packed pixels, so it is a good idea to compile them into the kernel | |
1309 | too. You can use only some font widths, as the driver uses generic | |
1310 | painting procedures (the secondary head does not use acceleration | |
1311 | engine). | |
1312 | ||
1313 | G450/G550 hardware can display TV picture only from secondary CRTC, | |
1314 | and it performs no scaling, so picture must have 525 or 625 lines. | |
1315 | ||
1316 | config FB_MATROX_I2C | |
1317 | tristate "Matrox I2C support" | |
166f60dd JS |
1318 | depends on FB_MATROX |
1319 | select FB_DDC | |
1da177e4 LT |
1320 | ---help--- |
1321 | This drivers creates I2C buses which are needed for accessing the | |
1322 | DDC (I2C) bus present on all Matroxes, an I2C bus which | |
1323 | interconnects Matrox optional devices, like MGA-TVO on G200 and | |
1324 | G400, and the secondary head DDC bus, present on G400 only. | |
1325 | ||
1326 | You can say Y or M here if you want to experiment with monitor | |
1327 | detection code. You must say Y or M here if you want to use either | |
1328 | second head of G400 or MGA-TVO on G200 or G400. | |
1329 | ||
1330 | If you compile it as module, it will create a module named | |
1331 | i2c-matroxfb. | |
1332 | ||
1333 | config FB_MATROX_MAVEN | |
1334 | tristate "G400 second head support" | |
1335 | depends on FB_MATROX_G && FB_MATROX_I2C | |
1336 | ---help--- | |
1337 | WARNING !!! This support does not work with G450 !!! | |
1338 | ||
1339 | Say Y or M here if you want to use a secondary head (meaning two | |
1340 | monitors in parallel) on G400 or MGA-TVO add-on on G200. Secondary | |
1341 | head is not compatible with accelerated XFree 3.3.x SVGA servers - | |
1342 | secondary head output is blanked while you are in X. With XFree | |
1343 | 3.9.17 preview you can use both heads if you use SVGA over fbdev or | |
1344 | the fbdev driver on first head and the fbdev driver on second head. | |
1345 | ||
1346 | If you compile it as module, two modules are created, | |
1347 | matroxfb_crtc2 and matroxfb_maven. Matroxfb_maven is needed for | |
1348 | both G200 and G400, matroxfb_crtc2 is needed only by G400. You must | |
1349 | also load i2c-matroxfb to get it to run. | |
1350 | ||
1351 | The driver starts in monitor mode and you must use the matroxset | |
1352 | tool (available at | |
1353 | <ftp://platan.vc.cvut.cz/pub/linux/matrox-latest/>) to switch it to | |
1354 | PAL or NTSC or to swap primary and secondary head outputs. | |
1355 | Secondary head driver also always start in 640x480 resolution, you | |
1356 | must use fbset to change it. | |
1357 | ||
1358 | Also do not forget that second head supports only 16 and 32 bpp | |
1359 | packed pixels, so it is a good idea to compile them into the kernel | |
1360 | too. You can use only some font widths, as the driver uses generic | |
1361 | painting procedures (the secondary head does not use acceleration | |
1362 | engine). | |
1363 | ||
1da177e4 LT |
1364 | config FB_RADEON |
1365 | tristate "ATI Radeon display support" | |
1366 | depends on FB && PCI | |
e0e34ef7 | 1367 | select FB_BACKLIGHT if FB_RADEON_BACKLIGHT |
1da177e4 LT |
1368 | select FB_MODE_HELPERS |
1369 | select FB_CFB_FILLRECT | |
1370 | select FB_CFB_COPYAREA | |
1371 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
1372 | select FB_MACMODES if PPC_OF |
1373 | help | |
1374 | Choose this option if you want to use an ATI Radeon graphics card as | |
1375 | a framebuffer device. There are both PCI and AGP versions. You | |
1376 | don't need to choose this to run the Radeon in plain VGA mode. | |
1377 | ||
1da177e4 | 1378 | There is a product page at |
631dd1a8 | 1379 | http://products.amd.com/en-us/GraphicCardResult.aspx |
5474c120 | 1380 | |
1da177e4 LT |
1381 | config FB_RADEON_I2C |
1382 | bool "DDC/I2C for ATI Radeon support" | |
1383 | depends on FB_RADEON | |
166f60dd | 1384 | select FB_DDC |
1da177e4 LT |
1385 | default y |
1386 | help | |
1387 | Say Y here if you want DDC/I2C support for your Radeon board. | |
1388 | ||
5474c120 MH |
1389 | config FB_RADEON_BACKLIGHT |
1390 | bool "Support for backlight control" | |
e0e34ef7 | 1391 | depends on FB_RADEON |
5474c120 MH |
1392 | default y |
1393 | help | |
1394 | Say Y here if you want to control the backlight of your display. | |
1395 | ||
1da177e4 LT |
1396 | config FB_RADEON_DEBUG |
1397 | bool "Lots of debug output from Radeon driver" | |
1398 | depends on FB_RADEON | |
1399 | default n | |
1400 | help | |
1401 | Say Y here if you want the Radeon driver to output all sorts | |
09509603 | 1402 | of debugging information to provide to the maintainer when |
1da177e4 LT |
1403 | something goes wrong. |
1404 | ||
1405 | config FB_ATY128 | |
1406 | tristate "ATI Rage128 display support" | |
1407 | depends on FB && PCI | |
1408 | select FB_CFB_FILLRECT | |
1409 | select FB_CFB_COPYAREA | |
1410 | select FB_CFB_IMAGEBLIT | |
e0e34ef7 | 1411 | select FB_BACKLIGHT if FB_ATY128_BACKLIGHT |
1da177e4 LT |
1412 | select FB_MACMODES if PPC_PMAC |
1413 | help | |
1414 | This driver supports graphics boards with the ATI Rage128 chips. | |
1415 | Say Y if you have such a graphics board and read | |
1416 | <file:Documentation/fb/aty128fb.txt>. | |
1417 | ||
1418 | To compile this driver as a module, choose M here: the | |
1419 | module will be called aty128fb. | |
1420 | ||
5474c120 MH |
1421 | config FB_ATY128_BACKLIGHT |
1422 | bool "Support for backlight control" | |
e0e34ef7 | 1423 | depends on FB_ATY128 |
5474c120 MH |
1424 | default y |
1425 | help | |
1426 | Say Y here if you want to control the backlight of your display. | |
1427 | ||
1da177e4 LT |
1428 | config FB_ATY |
1429 | tristate "ATI Mach64 display support" if PCI || ATARI | |
f2e782ef | 1430 | depends on FB && !SPARC32 |
1da177e4 LT |
1431 | select FB_CFB_FILLRECT |
1432 | select FB_CFB_COPYAREA | |
1433 | select FB_CFB_IMAGEBLIT | |
e0e34ef7 | 1434 | select FB_BACKLIGHT if FB_ATY_BACKLIGHT |
1da177e4 LT |
1435 | select FB_MACMODES if PPC |
1436 | help | |
1437 | This driver supports graphics boards with the ATI Mach64 chips. | |
1438 | Say Y if you have such a graphics board. | |
1439 | ||
1440 | To compile this driver as a module, choose M here: the | |
1441 | module will be called atyfb. | |
1442 | ||
1443 | config FB_ATY_CT | |
1444 | bool "Mach64 CT/VT/GT/LT (incl. 3D RAGE) support" | |
1445 | depends on PCI && FB_ATY | |
8d74c1fd | 1446 | default y if SPARC64 && PCI |
1da177e4 LT |
1447 | help |
1448 | Say Y here to support use of ATI's 64-bit Rage boards (or other | |
1449 | boards based on the Mach64 CT, VT, GT, and LT chipsets) as a | |
1450 | framebuffer device. The ATI product support page for these boards | |
631dd1a8 | 1451 | is at <http://support.ati.com/products/pc/mach64/mach64.html>. |
1da177e4 LT |
1452 | |
1453 | config FB_ATY_GENERIC_LCD | |
d1d34224 | 1454 | bool "Mach64 generic LCD support" |
1da177e4 LT |
1455 | depends on FB_ATY_CT |
1456 | help | |
1457 | Say Y if you have a laptop with an ATI Rage LT PRO, Rage Mobility, | |
1458 | Rage XC, or Rage XL chipset. | |
1459 | ||
1da177e4 LT |
1460 | config FB_ATY_GX |
1461 | bool "Mach64 GX support" if PCI | |
1462 | depends on FB_ATY | |
1463 | default y if ATARI | |
1464 | help | |
1465 | Say Y here to support use of the ATI Mach64 Graphics Expression | |
1466 | board (or other boards based on the Mach64 GX chipset) as a | |
1467 | framebuffer device. The ATI product support page for these boards | |
1468 | is at | |
1469 | <http://support.ati.com/products/pc/mach64/graphics_xpression.html>. | |
1470 | ||
5474c120 MH |
1471 | config FB_ATY_BACKLIGHT |
1472 | bool "Support for backlight control" | |
e0e34ef7 | 1473 | depends on FB_ATY |
5474c120 MH |
1474 | default y |
1475 | help | |
1476 | Say Y here if you want to control the backlight of your display. | |
1477 | ||
a268422d OZ |
1478 | config FB_S3 |
1479 | tristate "S3 Trio/Virge support" | |
1480 | depends on FB && PCI | |
1481 | select FB_CFB_FILLRECT | |
1482 | select FB_CFB_COPYAREA | |
1483 | select FB_CFB_IMAGEBLIT | |
1484 | select FB_TILEBLITTING | |
1485 | select FB_SVGALIB | |
b2f594fd | 1486 | select VGASTATE |
8db51668 | 1487 | select FONT_8x16 if FRAMEBUFFER_CONSOLE |
a268422d OZ |
1488 | ---help--- |
1489 | Driver for graphics boards with S3 Trio / S3 Virge chip. | |
1490 | ||
86c0f043 OZ |
1491 | config FB_S3_DDC |
1492 | bool "DDC for S3 support" | |
1493 | depends on FB_S3 | |
1494 | select FB_DDC | |
1495 | default y | |
1496 | help | |
1497 | Say Y here if you want DDC support for your S3 graphics card. | |
1498 | ||
1da177e4 LT |
1499 | config FB_SAVAGE |
1500 | tristate "S3 Savage support" | |
d1d34224 | 1501 | depends on FB && PCI |
1da177e4 LT |
1502 | select FB_MODE_HELPERS |
1503 | select FB_CFB_FILLRECT | |
1504 | select FB_CFB_COPYAREA | |
1505 | select FB_CFB_IMAGEBLIT | |
b2f594fd | 1506 | select VGASTATE |
1da177e4 LT |
1507 | help |
1508 | This driver supports notebooks and computers with S3 Savage PCI/AGP | |
1509 | chips. | |
1510 | ||
1511 | Say Y if you have such a graphics card. | |
1512 | ||
1513 | To compile this driver as a module, choose M here; the module | |
1514 | will be called savagefb. | |
1515 | ||
1516 | config FB_SAVAGE_I2C | |
1517 | bool "Enable DDC2 Support" | |
1518 | depends on FB_SAVAGE | |
166f60dd | 1519 | select FB_DDC |
1da177e4 LT |
1520 | help |
1521 | This enables I2C support for S3 Savage Chipsets. This is used | |
1522 | only for getting EDID information from the attached display | |
1523 | allowing for robust video mode handling and switching. | |
1524 | ||
1525 | Because fbdev-2.6 requires that drivers must be able to | |
1526 | independently validate video mode parameters, you should say Y | |
1527 | here. | |
1528 | ||
1529 | config FB_SAVAGE_ACCEL | |
1530 | bool "Enable Console Acceleration" | |
1531 | depends on FB_SAVAGE | |
1532 | default n | |
1533 | help | |
1534 | This option will compile in console acceleration support. If | |
1535 | the resulting framebuffer console has bothersome glitches, then | |
1536 | choose N here. | |
1537 | ||
1538 | config FB_SIS | |
544393fe | 1539 | tristate "SiS/XGI display support" |
1da177e4 LT |
1540 | depends on FB && PCI |
1541 | select FB_CFB_FILLRECT | |
1542 | select FB_CFB_COPYAREA | |
1543 | select FB_CFB_IMAGEBLIT | |
4b198289 | 1544 | select FB_BOOT_VESA_SUPPORT if FB_SIS = y |
1da177e4 | 1545 | help |
544393fe TW |
1546 | This is the frame buffer device driver for the SiS 300, 315, 330 |
1547 | and 340 series as well as XGI V3XT, V5, V8, Z7 graphics chipsets. | |
1548 | Specs available at <http://www.sis.com> and <http://www.xgitech.com>. | |
1da177e4 LT |
1549 | |
1550 | To compile this driver as a module, choose M here; the module | |
1551 | will be called sisfb. | |
1552 | ||
1553 | config FB_SIS_300 | |
1554 | bool "SiS 300 series support" | |
1555 | depends on FB_SIS | |
1556 | help | |
1557 | Say Y here to support use of the SiS 300/305, 540, 630 and 730. | |
1558 | ||
1559 | config FB_SIS_315 | |
544393fe | 1560 | bool "SiS 315/330/340 series and XGI support" |
1da177e4 LT |
1561 | depends on FB_SIS |
1562 | help | |
544393fe TW |
1563 | Say Y here to support use of the SiS 315, 330 and 340 series |
1564 | (315/H/PRO, 55x, 650, 651, 740, 330, 661, 741, 760, 761) as well | |
1565 | as XGI V3XT, V5, V8 and Z7. | |
1da177e4 | 1566 | |
6bde3ed9 JC |
1567 | config FB_VIA |
1568 | tristate "VIA UniChrome (Pro) and Chrome9 display support" | |
901b97d7 | 1569 | depends on FB && PCI && X86 |
6bde3ed9 JC |
1570 | select FB_CFB_FILLRECT |
1571 | select FB_CFB_COPYAREA | |
1572 | select FB_CFB_IMAGEBLIT | |
6bde3ed9 JC |
1573 | select I2C_ALGOBIT |
1574 | select I2C | |
7e0de022 | 1575 | select GPIOLIB |
6bde3ed9 JC |
1576 | help |
1577 | This is the frame buffer device driver for Graphics chips of VIA | |
1578 | UniChrome (Pro) Family (CLE266,PM800/CN400,P4M800CE/P4M800Pro/ | |
1579 | CN700/VN800,CX700/VX700,P4M890) and Chrome9 Family (K8M890,CN896 | |
1580 | /P4M900,VX800) | |
1581 | Say Y if you have a VIA UniChrome graphics board. | |
1582 | ||
1583 | To compile this driver as a module, choose M here: the | |
1584 | module will be called viafb. | |
7e0de022 | 1585 | |
2b78a963 FTS |
1586 | if FB_VIA |
1587 | ||
1588 | config FB_VIA_DIRECT_PROCFS | |
1589 | bool "direct hardware access via procfs (DEPRECATED)(DANGEROUS)" | |
1590 | depends on FB_VIA | |
1591 | default n | |
1592 | help | |
1593 | Allow direct hardware access to some output registers via procfs. | |
1594 | This is dangerous but may provide the only chance to get the | |
1595 | correct output device configuration. | |
1596 | Its use is strongly discouraged. | |
1597 | ||
2946294f FTS |
1598 | config FB_VIA_X_COMPATIBILITY |
1599 | bool "X server compatibility" | |
1600 | depends on FB_VIA | |
1601 | default n | |
1602 | help | |
1603 | This option reduces the functionality (power saving, ...) of the | |
1604 | framebuffer to avoid negative impact on the OpenChrome X server. | |
1605 | If you use any X server other than fbdev you should enable this | |
1606 | otherwise it should be safe to disable it and allow using all | |
1607 | features. | |
1608 | ||
2b78a963 FTS |
1609 | endif |
1610 | ||
1da177e4 LT |
1611 | config FB_NEOMAGIC |
1612 | tristate "NeoMagic display support" | |
1613 | depends on FB && PCI | |
1614 | select FB_MODE_HELPERS | |
1615 | select FB_CFB_FILLRECT | |
1616 | select FB_CFB_COPYAREA | |
1617 | select FB_CFB_IMAGEBLIT | |
b2f594fd | 1618 | select VGASTATE |
1da177e4 LT |
1619 | help |
1620 | This driver supports notebooks with NeoMagic PCI chips. | |
1621 | Say Y if you have such a graphics card. | |
1622 | ||
1623 | To compile this driver as a module, choose M here: the | |
1624 | module will be called neofb. | |
1625 | ||
1626 | config FB_KYRO | |
1627 | tristate "IMG Kyro support" | |
1628 | depends on FB && PCI | |
1629 | select FB_CFB_FILLRECT | |
1630 | select FB_CFB_COPYAREA | |
1631 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
1632 | help |
1633 | Say Y here if you have a STG4000 / Kyro / PowerVR 3 based | |
1634 | graphics board. | |
1635 | ||
1636 | To compile this driver as a module, choose M here: the | |
1637 | module will be called kyrofb. | |
1638 | ||
1639 | config FB_3DFX | |
4edad7f0 | 1640 | tristate "3Dfx Banshee/Voodoo3/Voodoo5 display support" |
1da177e4 LT |
1641 | depends on FB && PCI |
1642 | select FB_CFB_IMAGEBLIT | |
1643 | select FB_CFB_FILLRECT | |
1644 | select FB_CFB_COPYAREA | |
feff3880 | 1645 | select FB_MODE_HELPERS |
1da177e4 | 1646 | help |
4edad7f0 KH |
1647 | This driver supports graphics boards with the 3Dfx Banshee, |
1648 | Voodoo3 or VSA-100 (aka Voodoo4/5) chips. Say Y if you have | |
1649 | such a graphics board. | |
1da177e4 LT |
1650 | |
1651 | To compile this driver as a module, choose M here: the | |
1652 | module will be called tdfxfb. | |
1653 | ||
1654 | config FB_3DFX_ACCEL | |
d1d34224 KC |
1655 | bool "3Dfx Acceleration functions" |
1656 | depends on FB_3DFX | |
1da177e4 | 1657 | ---help--- |
4edad7f0 KH |
1658 | This will compile the 3Dfx Banshee/Voodoo3/VSA-100 frame buffer |
1659 | device driver with acceleration functions. | |
1da177e4 | 1660 | |
feff3880 KH |
1661 | config FB_3DFX_I2C |
1662 | bool "Enable DDC/I2C support" | |
d1d34224 | 1663 | depends on FB_3DFX |
feff3880 KH |
1664 | select FB_DDC |
1665 | default y | |
1666 | help | |
1667 | Say Y here if you want DDC/I2C support for your 3dfx Voodoo3. | |
1668 | ||
1da177e4 LT |
1669 | config FB_VOODOO1 |
1670 | tristate "3Dfx Voodoo Graphics (sst1) support" | |
1671 | depends on FB && PCI | |
1672 | select FB_CFB_FILLRECT | |
1673 | select FB_CFB_COPYAREA | |
1674 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
1675 | ---help--- |
1676 | Say Y here if you have a 3Dfx Voodoo Graphics (Voodoo1/sst1) or | |
1677 | Voodoo2 (cvg) based graphics card. | |
1678 | ||
1679 | To compile this driver as a module, choose M here: the | |
1680 | module will be called sstfb. | |
1681 | ||
1682 | WARNING: Do not use any application that uses the 3D engine | |
1683 | (namely glide) while using this driver. | |
e403149c | 1684 | Please read the <file:Documentation/fb/sstfb.txt> for supported |
1da177e4 LT |
1685 | options and other important info support. |
1686 | ||
558b7bd8 OZ |
1687 | config FB_VT8623 |
1688 | tristate "VIA VT8623 support" | |
1689 | depends on FB && PCI | |
1690 | select FB_CFB_FILLRECT | |
1691 | select FB_CFB_COPYAREA | |
1692 | select FB_CFB_IMAGEBLIT | |
1693 | select FB_TILEBLITTING | |
1694 | select FB_SVGALIB | |
1695 | select VGASTATE | |
1696 | select FONT_8x16 if FRAMEBUFFER_CONSOLE | |
1697 | ---help--- | |
1698 | Driver for CastleRock integrated graphics core in the | |
1699 | VIA VT8623 [Apollo CLE266] chipset. | |
1700 | ||
1da177e4 | 1701 | config FB_TRIDENT |
04645fc3 | 1702 | tristate "Trident/CyberXXX/CyberBlade support" |
1da177e4 LT |
1703 | depends on FB && PCI |
1704 | select FB_CFB_FILLRECT | |
1705 | select FB_CFB_COPYAREA | |
1706 | select FB_CFB_IMAGEBLIT | |
1da177e4 | 1707 | ---help--- |
4edad7f0 KH |
1708 | This is the frame buffer device driver for Trident PCI/AGP chipsets. |
1709 | Supported chipset families are TGUI 9440/96XX, 3DImage, Blade3D | |
1710 | and Blade XP. | |
1711 | There are also integrated versions of these chips called CyberXXXX, | |
1712 | CyberImage or CyberBlade. These chips are mostly found in laptops | |
ddb53d48 KH |
1713 | but also on some motherboards including early VIA EPIA motherboards. |
1714 | For more information, read <file:Documentation/fb/tridentfb.txt> | |
1da177e4 LT |
1715 | |
1716 | Say Y if you have such a graphics board. | |
1717 | ||
1718 | To compile this driver as a module, choose M here: the | |
1719 | module will be called tridentfb. | |
1720 | ||
681e1473 OZ |
1721 | config FB_ARK |
1722 | tristate "ARK 2000PV support" | |
1723 | depends on FB && PCI | |
1724 | select FB_CFB_FILLRECT | |
1725 | select FB_CFB_COPYAREA | |
1726 | select FB_CFB_IMAGEBLIT | |
1727 | select FB_TILEBLITTING | |
1728 | select FB_SVGALIB | |
1729 | select VGASTATE | |
1730 | select FONT_8x16 if FRAMEBUFFER_CONSOLE | |
1731 | ---help--- | |
1732 | Driver for PCI graphics boards with ARK 2000PV chip | |
1733 | and ICS 5342 RAMDAC. | |
1734 | ||
1da177e4 | 1735 | config FB_PM3 |
d1d34224 KC |
1736 | tristate "Permedia3 support" |
1737 | depends on FB && PCI | |
f23a06f0 KH |
1738 | select FB_CFB_FILLRECT |
1739 | select FB_CFB_COPYAREA | |
1740 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
1741 | help |
1742 | This is the frame buffer device driver for the 3DLabs Permedia3 | |
1743 | chipset, used in Formac ProFormance III, 3DLabs Oxygen VX1 & | |
1744 | similar boards, 3DLabs Permedia3 Create!, Appian Jeronimo 2000 | |
1745 | and maybe other boards. | |
1746 | ||
2ece5f43 SS |
1747 | config FB_CARMINE |
1748 | tristate "Fujitsu carmine frame buffer support" | |
1749 | depends on FB && PCI | |
1750 | select FB_CFB_FILLRECT | |
1751 | select FB_CFB_COPYAREA | |
1752 | select FB_CFB_IMAGEBLIT | |
1753 | help | |
1754 | This is the frame buffer device driver for the Fujitsu Carmine chip. | |
1755 | The driver provides two independent frame buffer devices. | |
1756 | ||
1757 | choice | |
1758 | depends on FB_CARMINE | |
1759 | prompt "DRAM timing" | |
1760 | default FB_CARMINE_DRAM_EVAL | |
1761 | ||
1762 | config FB_CARMINE_DRAM_EVAL | |
1763 | bool "Eval board timings" | |
1764 | help | |
1765 | Use timings which work on the eval card. | |
1766 | ||
1767 | config CARMINE_DRAM_CUSTOM | |
1768 | bool "Custom board timings" | |
1769 | help | |
1770 | Use custom board timings. | |
1771 | endchoice | |
1772 | ||
1da177e4 LT |
1773 | config FB_AU1100 |
1774 | bool "Au1100 LCD Driver" | |
37663860 | 1775 | depends on (FB = y) && MIPS_ALCHEMY |
d1709e47 RB |
1776 | select FB_CFB_FILLRECT |
1777 | select FB_CFB_COPYAREA | |
1778 | select FB_CFB_IMAGEBLIT | |
1779 | help | |
1780 | This is the framebuffer driver for the AMD Au1100 SOC. It can drive | |
1781 | various panels and CRTs by passing in kernel cmd line option | |
1782 | au1100fb:panel=<name>. | |
1da177e4 | 1783 | |
f95ec3c6 | 1784 | config FB_AU1200 |
809f36c6 | 1785 | bool "Au1200/Au1300 LCD Driver" |
37663860 | 1786 | depends on (FB = y) && MIPS_ALCHEMY |
4ee58461 ML |
1787 | select FB_SYS_FILLRECT |
1788 | select FB_SYS_COPYAREA | |
1789 | select FB_SYS_IMAGEBLIT | |
1790 | select FB_SYS_FOPS | |
f95ec3c6 | 1791 | help |
809f36c6 ML |
1792 | This is the framebuffer driver for the Au1200/Au1300 SOCs. |
1793 | It can drive various panels and CRTs by passing in kernel cmd line | |
1794 | option au1200fb:panel=<name>. | |
f95ec3c6 | 1795 | |
d6ff7d0f | 1796 | config FB_VT8500 |
3d20837d | 1797 | bool "VIA VT8500 framebuffer support" |
e7b99537 | 1798 | depends on (FB = y) && ARM && ARCH_VT8500 |
18a434b5 TP |
1799 | select FB_SYS_FILLRECT if (!FB_WMT_GE_ROPS) |
1800 | select FB_SYS_COPYAREA if (!FB_WMT_GE_ROPS) | |
d6ff7d0f | 1801 | select FB_SYS_IMAGEBLIT |
7ab0a484 | 1802 | select FB_MODE_HELPERS |
e45f265e | 1803 | select VIDEOMODE_HELPERS |
d6ff7d0f AC |
1804 | help |
1805 | This is the framebuffer driver for VIA VT8500 integrated LCD | |
1806 | controller. | |
1807 | ||
1808 | config FB_WM8505 | |
3d20837d | 1809 | bool "Wondermedia WM8xxx-series frame buffer support" |
e7b99537 | 1810 | depends on (FB = y) && ARM && ARCH_VT8500 |
18a434b5 TP |
1811 | select FB_SYS_FILLRECT if (!FB_WMT_GE_ROPS) |
1812 | select FB_SYS_COPYAREA if (!FB_WMT_GE_ROPS) | |
d6ff7d0f | 1813 | select FB_SYS_IMAGEBLIT |
7ab0a484 | 1814 | select FB_MODE_HELPERS |
e45f265e | 1815 | select VIDEOMODE_HELPERS |
d6ff7d0f | 1816 | help |
3d20837d TP |
1817 | This is the framebuffer driver for WonderMedia WM8xxx-series |
1818 | integrated LCD controller. This driver covers the WM8505, WM8650 | |
1819 | and WM8850 SoCs. | |
d6ff7d0f | 1820 | |
18a434b5 | 1821 | config FB_WMT_GE_ROPS |
3d20837d | 1822 | bool "VT8500/WM8xxx accelerated raster ops support" |
18a434b5 TP |
1823 | depends on (FB = y) && (FB_VT8500 || FB_WM8505) |
1824 | default n | |
d6ff7d0f | 1825 | help |
18a434b5 TP |
1826 | This adds support for accelerated raster operations on the |
1827 | VIA VT8500 and Wondermedia 85xx series SoCs. | |
d6ff7d0f | 1828 | |
1da177e4 LT |
1829 | source "drivers/video/geode/Kconfig" |
1830 | ||
1da177e4 LT |
1831 | config FB_HIT |
1832 | tristate "HD64461 Frame Buffer support" | |
1833 | depends on FB && HD64461 | |
1834 | select FB_CFB_FILLRECT | |
1835 | select FB_CFB_COPYAREA | |
1836 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
1837 | help |
1838 | This is the frame buffer device driver for the Hitachi HD64461 LCD | |
1839 | frame buffer card. | |
1840 | ||
1841 | config FB_PMAG_AA | |
1842 | bool "PMAG-AA TURBOchannel framebuffer support" | |
a9350003 | 1843 | depends on (FB = y) && TC |
1da177e4 LT |
1844 | select FB_CFB_FILLRECT |
1845 | select FB_CFB_COPYAREA | |
1846 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
1847 | help |
1848 | Support for the PMAG-AA TURBOchannel framebuffer card (1280x1024x1) | |
1849 | used mainly in the MIPS-based DECstation series. | |
1850 | ||
1851 | config FB_PMAG_BA | |
335dc50c MR |
1852 | tristate "PMAG-BA TURBOchannel framebuffer support" |
1853 | depends on FB && TC | |
1da177e4 LT |
1854 | select FB_CFB_FILLRECT |
1855 | select FB_CFB_COPYAREA | |
1856 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
1857 | help |
1858 | Support for the PMAG-BA TURBOchannel framebuffer card (1024x864x8) | |
1859 | used mainly in the MIPS-based DECstation series. | |
1860 | ||
1861 | config FB_PMAGB_B | |
9084b005 | 1862 | tristate "PMAGB-B TURBOchannel framebuffer support" |
28ea28a6 | 1863 | depends on FB && TC |
1da177e4 LT |
1864 | select FB_CFB_FILLRECT |
1865 | select FB_CFB_COPYAREA | |
1866 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
1867 | help |
1868 | Support for the PMAGB-B TURBOchannel framebuffer card used mainly | |
1869 | in the MIPS-based DECstation series. The card is currently only | |
1870 | supported in 1280x1024x8 mode. | |
1871 | ||
1872 | config FB_MAXINE | |
1873 | bool "Maxine (Personal DECstation) onboard framebuffer support" | |
a9350003 | 1874 | depends on (FB = y) && MACH_DECSTATION |
1da177e4 LT |
1875 | select FB_CFB_FILLRECT |
1876 | select FB_CFB_COPYAREA | |
1877 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
1878 | help |
1879 | Support for the onboard framebuffer (1024x768x8) in the Personal | |
1880 | DECstation series (Personal DECstation 5000/20, /25, /33, /50, | |
1881 | Codename "Maxine"). | |
1882 | ||
1da177e4 | 1883 | config FB_G364 |
b38817dd YY |
1884 | bool "G364 frame buffer support" |
1885 | depends on (FB = y) && (MIPS_MAGNUM_4000 || OLIVETTI_M700) | |
1da177e4 LT |
1886 | select FB_CFB_FILLRECT |
1887 | select FB_CFB_COPYAREA | |
1888 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
1889 | help |
1890 | The G364 driver is the framebuffer used in MIPS Magnum 4000 and | |
1891 | Olivetti M700-10 systems. | |
1892 | ||
1893 | config FB_68328 | |
1894 | bool "Motorola 68328 native frame buffer support" | |
833f8062 | 1895 | depends on (FB = y) && (M68328 || M68EZ328 || M68VZ328) |
1da177e4 LT |
1896 | select FB_CFB_FILLRECT |
1897 | select FB_CFB_COPYAREA | |
1898 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
1899 | help |
1900 | Say Y here if you want to support the built-in frame buffer of | |
1901 | the Motorola 68328 CPU family. | |
1902 | ||
638772c7 LB |
1903 | config FB_PXA168 |
1904 | tristate "PXA168/910 LCD framebuffer support" | |
1905 | depends on FB && (CPU_PXA168 || CPU_PXA910) | |
1906 | select FB_CFB_FILLRECT | |
1907 | select FB_CFB_COPYAREA | |
1908 | select FB_CFB_IMAGEBLIT | |
1909 | ---help--- | |
1910 | Frame buffer driver for the built-in LCD controller in the Marvell | |
1911 | MMP processor. | |
1912 | ||
1da177e4 LT |
1913 | config FB_PXA |
1914 | tristate "PXA LCD framebuffer support" | |
1915 | depends on FB && ARCH_PXA | |
1916 | select FB_CFB_FILLRECT | |
1917 | select FB_CFB_COPYAREA | |
1918 | select FB_CFB_IMAGEBLIT | |
1da177e4 LT |
1919 | ---help--- |
1920 | Frame buffer driver for the built-in LCD controller in the Intel | |
1921 | PXA2x0 processor. | |
1922 | ||
1923 | This driver is also available as a module ( = code which can be | |
1924 | inserted and removed from the running kernel whenever you want). The | |
74b4f042 | 1925 | module will be called pxafb. If you want to compile it as a module, |
39f5fb30 | 1926 | say M here and read <file:Documentation/kbuild/modules.txt>. |
1da177e4 LT |
1927 | |
1928 | If unsure, say N. | |
1929 | ||
198fc108 EM |
1930 | config FB_PXA_OVERLAY |
1931 | bool "Support PXA27x/PXA3xx Overlay(s) as framebuffer" | |
1932 | default n | |
1933 | depends on FB_PXA && (PXA27x || PXA3xx) | |
1934 | ||
3c42a449 EM |
1935 | config FB_PXA_SMARTPANEL |
1936 | bool "PXA Smartpanel LCD support" | |
7f1133cb | 1937 | default n |
3c42a449 EM |
1938 | depends on FB_PXA |
1939 | ||
1da177e4 LT |
1940 | config FB_PXA_PARAMETERS |
1941 | bool "PXA LCD command line parameters" | |
1942 | default n | |
1943 | depends on FB_PXA | |
1944 | ---help--- | |
1945 | Enable the use of kernel command line or module parameters | |
1946 | to configure the physical properties of the LCD panel when | |
1947 | using the PXA LCD driver. | |
1948 | ||
1949 | This option allows you to override the panel parameters | |
1950 | supplied by the platform in order to support multiple | |
1951 | different models of flatpanel. If you will only be using a | |
1952 | single model of flatpanel then you can safely leave this | |
1953 | option disabled. | |
1954 | ||
1955 | <file:Documentation/fb/pxafb.txt> describes the available parameters. | |
1956 | ||
364dbdf3 DM |
1957 | config PXA3XX_GCU |
1958 | tristate "PXA3xx 2D graphics accelerator driver" | |
1959 | depends on FB_PXA | |
1960 | help | |
1961 | Kernelspace driver for the 2D graphics controller unit (GCU) | |
1962 | found on PXA3xx processors. There is a counterpart driver in the | |
1963 | DirectFB suite, see http://www.directfb.org/ | |
1964 | ||
1965 | If you compile this as a module, it will be called pxa3xx_gcu. | |
1966 | ||
22caf042 MR |
1967 | config FB_MBX |
1968 | tristate "2700G LCD framebuffer support" | |
1969 | depends on FB && ARCH_PXA | |
1970 | select FB_CFB_FILLRECT | |
1971 | select FB_CFB_COPYAREA | |
1972 | select FB_CFB_IMAGEBLIT | |
1973 | ---help--- | |
1974 | Framebuffer driver for the Intel 2700G (Marathon) Graphics | |
1975 | Accelerator | |
1976 | ||
1977 | config FB_MBX_DEBUG | |
1978 | bool "Enable debugging info via debugfs" | |
1979 | depends on FB_MBX && DEBUG_FS | |
1980 | default n | |
1981 | ---help--- | |
1982 | Enable this if you want debugging information using the debug | |
1983 | filesystem (debugfs) | |
1984 | ||
1985 | If unsure, say N. | |
1986 | ||
9b53a9e2 YS |
1987 | config FB_FSL_DIU |
1988 | tristate "Freescale DIU framebuffer support" | |
1989 | depends on FB && FSL_SOC | |
8b856f04 | 1990 | select FB_MODE_HELPERS |
9b53a9e2 YS |
1991 | select FB_CFB_FILLRECT |
1992 | select FB_CFB_COPYAREA | |
1993 | select FB_CFB_IMAGEBLIT | |
1994 | select PPC_LIB_RHEAP | |
1995 | ---help--- | |
1996 | Framebuffer driver for the Freescale SoC DIU | |
1997 | ||
ecc41d5e RD |
1998 | config FB_W100 |
1999 | tristate "W100 frame buffer support" | |
e5dd3cbd | 2000 | depends on FB && ARCH_PXA |
ecc41d5e RD |
2001 | select FB_CFB_FILLRECT |
2002 | select FB_CFB_COPYAREA | |
2003 | select FB_CFB_IMAGEBLIT | |
ecc41d5e RD |
2004 | ---help--- |
2005 | Frame buffer driver for the w100 as found on the Sharp SL-Cxx series. | |
e5dd3cbd | 2006 | It can also drive the w3220 chip found on iPAQ hx4700. |
ecc41d5e RD |
2007 | |
2008 | This driver is also available as a module ( = code which can be | |
2009 | inserted and removed from the running kernel whenever you want). The | |
74b4f042 | 2010 | module will be called w100fb. If you want to compile it as a module, |
39f5fb30 | 2011 | say M here and read <file:Documentation/kbuild/modules.txt>. |
ecc41d5e RD |
2012 | |
2013 | If unsure, say N. | |
1da177e4 | 2014 | |
cfb4f5d1 MD |
2015 | config FB_SH_MOBILE_LCDC |
2016 | tristate "SuperH Mobile LCDC framebuffer support" | |
7278a221 | 2017 | depends on FB && (SUPERH || ARCH_SHMOBILE) && HAVE_CLK |
2540c111 MD |
2018 | select FB_SYS_FILLRECT |
2019 | select FB_SYS_COPYAREA | |
2020 | select FB_SYS_IMAGEBLIT | |
2021 | select FB_SYS_FOPS | |
8564557a | 2022 | select FB_DEFERRED_IO |
3b0fd9d7 | 2023 | select FB_BACKLIGHT |
9fd04fe3 | 2024 | select SH_MIPI_DSI if SH_LCD_MIPI_DSI |
cfb4f5d1 MD |
2025 | ---help--- |
2026 | Frame buffer driver for the on-chip SH-Mobile LCD controller. | |
2027 | ||
6011bdea GL |
2028 | config FB_SH_MOBILE_HDMI |
2029 | tristate "SuperH Mobile HDMI controller support" | |
2030 | depends on FB_SH_MOBILE_LCDC | |
2031 | select FB_MODE_HELPERS | |
630f2d44 GL |
2032 | select SOUND |
2033 | select SND | |
3056c70c | 2034 | select SND_SOC |
6011bdea GL |
2035 | ---help--- |
2036 | Driver for the on-chip SH-Mobile HDMI controller. | |
2037 | ||
b53cde35 DES |
2038 | config FB_TMIO |
2039 | tristate "Toshiba Mobile IO FrameBuffer support" | |
2040 | depends on FB && MFD_CORE | |
2041 | select FB_CFB_FILLRECT | |
2042 | select FB_CFB_COPYAREA | |
2043 | select FB_CFB_IMAGEBLIT | |
2044 | ---help--- | |
2045 | Frame buffer driver for the Toshiba Mobile IO integrated as found | |
2046 | on the Sharp SL-6000 series | |
2047 | ||
2048 | This driver is also available as a module ( = code which can be | |
2049 | inserted and removed from the running kernel whenever you want). The | |
2050 | module will be called tmiofb. If you want to compile it as a module, | |
2051 | say M here and read <file:Documentation/kbuild/modules.txt>. | |
2052 | ||
2053 | If unsure, say N. | |
2054 | ||
2055 | config FB_TMIO_ACCELL | |
2056 | bool "tmiofb acceleration" | |
2057 | depends on FB_TMIO | |
2058 | default y | |
2059 | ||
ec549a0f BD |
2060 | config FB_S3C |
2061 | tristate "Samsung S3C framebuffer support" | |
4e45a765 JH |
2062 | depends on FB && (CPU_S3C2416 || ARCH_S3C64XX || ARCH_S5P64X0 || \ |
2063 | ARCH_S5PC100 || ARCH_S5PV210 || ARCH_EXYNOS) | |
ec549a0f BD |
2064 | select FB_CFB_FILLRECT |
2065 | select FB_CFB_COPYAREA | |
2066 | select FB_CFB_IMAGEBLIT | |
2067 | ---help--- | |
2068 | Frame buffer driver for the built-in FB controller in the Samsung | |
2069 | SoC line from the S3C2443 onwards, including the S3C2416, S3C2450, | |
2070 | and the S3C64XX series such as the S3C6400 and S3C6410. | |
2071 | ||
2072 | These chips all have the same basic framebuffer design with the | |
2073 | actual capabilities depending on the chip. For instance the S3C6400 | |
2074 | and S3C6410 support 4 hardware windows whereas the S3C24XX series | |
2075 | currently only have two. | |
2076 | ||
2077 | Currently the support is only for the S3C6400 and S3C6410 SoCs. | |
2078 | ||
2079 | config FB_S3C_DEBUG_REGWRITE | |
2080 | bool "Debug register writes" | |
2081 | depends on FB_S3C | |
2082 | ---help--- | |
975d352b | 2083 | Show all register writes via pr_debug() |
ec549a0f | 2084 | |
20fd5767 AP |
2085 | config FB_S3C2410 |
2086 | tristate "S3C2410 LCD framebuffer support" | |
b130d5c2 | 2087 | depends on FB && ARCH_S3C24XX |
20fd5767 AP |
2088 | select FB_CFB_FILLRECT |
2089 | select FB_CFB_COPYAREA | |
2090 | select FB_CFB_IMAGEBLIT | |
20fd5767 AP |
2091 | ---help--- |
2092 | Frame buffer driver for the built-in LCD controller in the Samsung | |
2093 | S3C2410 processor. | |
2094 | ||
2095 | This driver is also available as a module ( = code which can be | |
2096 | inserted and removed from the running kernel whenever you want). The | |
2097 | module will be called s3c2410fb. If you want to compile it as a module, | |
39f5fb30 | 2098 | say M here and read <file:Documentation/kbuild/modules.txt>. |
20fd5767 AP |
2099 | |
2100 | If unsure, say N. | |
2101 | config FB_S3C2410_DEBUG | |
2102 | bool "S3C2410 lcd debug messages" | |
2103 | depends on FB_S3C2410 | |
2104 | help | |
2105 | Turn on debugging messages. Note that you can set/unset at run time | |
2106 | through sysfs | |
2107 | ||
86619708 WQ |
2108 | config FB_NUC900 |
2109 | bool "NUC900 LCD framebuffer support" | |
2110 | depends on FB && ARCH_W90X900 | |
2111 | select FB_CFB_FILLRECT | |
2112 | select FB_CFB_COPYAREA | |
2113 | select FB_CFB_IMAGEBLIT | |
2114 | ---help--- | |
2115 | Frame buffer driver for the built-in LCD controller in the Nuvoton | |
2116 | NUC900 processor | |
2117 | ||
2118 | config GPM1040A0_320X240 | |
2119 | bool "Giantplus Technology GPM1040A0 320x240 Color TFT LCD" | |
2120 | depends on FB_NUC900 | |
2121 | ||
5fc404e4 BD |
2122 | config FB_SM501 |
2123 | tristate "Silicon Motion SM501 framebuffer support" | |
2124 | depends on FB && MFD_SM501 | |
2125 | select FB_CFB_FILLRECT | |
2126 | select FB_CFB_COPYAREA | |
2127 | select FB_CFB_IMAGEBLIT | |
2128 | ---help--- | |
2129 | Frame buffer driver for the CRT and LCD controllers in the Silicon | |
2130 | Motion SM501. | |
2131 | ||
2132 | This driver is also available as a module ( = code which can be | |
2133 | inserted and removed from the running kernel whenever you want). The | |
2134 | module will be called sm501fb. If you want to compile it as a module, | |
e403149c | 2135 | say M here and read <file:Documentation/kbuild/modules.txt>. |
5fc404e4 BD |
2136 | |
2137 | If unsure, say N. | |
2138 | ||
3c8a63e2 SG |
2139 | config FB_SMSCUFX |
2140 | tristate "SMSC UFX6000/7000 USB Framebuffer support" | |
2141 | depends on FB && USB | |
2142 | select FB_MODE_HELPERS | |
2143 | select FB_SYS_FILLRECT | |
2144 | select FB_SYS_COPYAREA | |
2145 | select FB_SYS_IMAGEBLIT | |
2146 | select FB_SYS_FOPS | |
2147 | select FB_DEFERRED_IO | |
2148 | ---help--- | |
2149 | This is a kernel framebuffer driver for SMSC UFX USB devices. | |
2150 | Supports fbdev clients like xf86-video-fbdev, kdrive, fbi, and | |
2151 | mplayer -vo fbdev. Supports both UFX6000 (USB 2.0) and UFX7000 | |
2152 | (USB 3.0) devices. | |
2153 | To compile as a module, choose M here: the module name is smscufx. | |
2154 | ||
96f8d864 PM |
2155 | config FB_UDL |
2156 | tristate "Displaylink USB Framebuffer support" | |
2157 | depends on FB && USB | |
2158 | select FB_MODE_HELPERS | |
2159 | select FB_SYS_FILLRECT | |
2160 | select FB_SYS_COPYAREA | |
2161 | select FB_SYS_IMAGEBLIT | |
2162 | select FB_SYS_FOPS | |
2163 | select FB_DEFERRED_IO | |
2164 | ---help--- | |
2165 | This is a kernel framebuffer driver for DisplayLink USB devices. | |
2166 | Supports fbdev clients like xf86-video-fbdev, kdrive, fbi, and | |
2167 | mplayer -vo fbdev. Supports all USB 2.0 era DisplayLink devices. | |
2168 | To compile as a module, choose M here: the module name is udlfb. | |
5fc404e4 | 2169 | |
a3d89983 | 2170 | config FB_IBM_GXT4500 |
6c39dcc4 | 2171 | tristate "Framebuffer support for IBM GXT4000P/4500P/6000P/6500P adaptors" |
0058f479 | 2172 | depends on FB && PPC |
a3d89983 PM |
2173 | select FB_CFB_FILLRECT |
2174 | select FB_CFB_COPYAREA | |
2175 | select FB_CFB_IMAGEBLIT | |
2176 | ---help--- | |
6c39dcc4 DH |
2177 | Say Y here to enable support for the IBM GXT4000P/6000P and |
2178 | GXT4500P/6500P display adaptor based on Raster Engine RC1000, | |
2179 | found on some IBM System P (pSeries) machines. This driver | |
2180 | doesn't use Geometry Engine GT1000. | |
a3d89983 | 2181 | |
310d8c11 | 2182 | config FB_PS3 |
9e6b99bd GU |
2183 | tristate "PS3 GPU framebuffer driver" |
2184 | depends on FB && PS3_PS3AV | |
92c4579d GU |
2185 | select FB_SYS_FILLRECT |
2186 | select FB_SYS_COPYAREA | |
2187 | select FB_SYS_IMAGEBLIT | |
2188 | select FB_SYS_FOPS | |
23e9c94c | 2189 | select VT_HW_CONSOLE_BINDING if FRAMEBUFFER_CONSOLE |
310d8c11 GU |
2190 | ---help--- |
2191 | Include support for the virtual frame buffer in the PS3 platform. | |
2192 | ||
2193 | config FB_PS3_DEFAULT_SIZE_M | |
2194 | int "PS3 default frame buffer size (in MiB)" | |
2195 | depends on FB_PS3 | |
50b2529e | 2196 | default 9 |
310d8c11 GU |
2197 | ---help--- |
2198 | This is the default size (in MiB) of the virtual frame buffer in | |
2199 | the PS3. | |
2200 | The default value can be overridden on the kernel command line | |
2201 | using the "ps3fb" option (e.g. "ps3fb=9M"); | |
2202 | ||
147394c8 AK |
2203 | config FB_XILINX |
2204 | tristate "Xilinx frame buffer support" | |
196bf9f3 | 2205 | depends on FB && (XILINX_VIRTEX || MICROBLAZE || ARCH_ZYNQ) |
147394c8 AK |
2206 | select FB_CFB_FILLRECT |
2207 | select FB_CFB_COPYAREA | |
2208 | select FB_CFB_IMAGEBLIT | |
2209 | ---help--- | |
2210 | Include support for the Xilinx ML300/ML403 reference design | |
2211 | framebuffer. ML300 carries a 640*480 LCD display on the board, | |
2212 | ML403 uses a standard DB15 VGA connector. | |
2213 | ||
c289ba2d AH |
2214 | config FB_GOLDFISH |
2215 | tristate "Goldfish Framebuffer" | |
e5ee7305 | 2216 | depends on FB && HAS_DMA |
c289ba2d AH |
2217 | select FB_CFB_FILLRECT |
2218 | select FB_CFB_COPYAREA | |
2219 | select FB_CFB_IMAGEBLIT | |
2220 | ---help--- | |
2221 | Framebuffer driver for Goldfish Virtual Platform | |
2222 | ||
5abe3b40 YY |
2223 | config FB_COBALT |
2224 | tristate "Cobalt server LCD frame buffer support" | |
13f36e9e | 2225 | depends on FB && (MIPS_COBALT || MIPS_SEAD3) |
5abe3b40 | 2226 | |
4a25e418 | 2227 | config FB_SH7760 |
5c72f303 NI |
2228 | bool "SH7760/SH7763/SH7720/SH7721 LCDC support" |
2229 | depends on FB && (CPU_SUBTYPE_SH7760 || CPU_SUBTYPE_SH7763 \ | |
2230 | || CPU_SUBTYPE_SH7720 || CPU_SUBTYPE_SH7721) | |
2231 | select FB_CFB_FILLRECT | |
2232 | select FB_CFB_COPYAREA | |
2233 | select FB_CFB_IMAGEBLIT | |
2234 | ---help--- | |
2235 | Support for the SH7760/SH7763/SH7720/SH7721 integrated | |
2236 | (D)STN/TFT LCD Controller. | |
2237 | Supports display resolutions up to 1024x1024 pixel, grayscale and | |
2238 | color operation, with depths ranging from 1 bpp to 8 bpp monochrome | |
2239 | and 8, 15 or 16 bpp color; 90 degrees clockwise display rotation for | |
2240 | panels <= 320 pixel horizontal resolution. | |
4a25e418 | 2241 | |
4ed824d9 | 2242 | config FB_DA8XX |
979778ff DE |
2243 | tristate "DA8xx/OMAP-L1xx/AM335x Framebuffer support" |
2244 | depends on FB && (ARCH_DAVINCI_DA8XX || SOC_AM33XX) | |
4ed824d9 SR |
2245 | select FB_CFB_FILLRECT |
2246 | select FB_CFB_COPYAREA | |
2247 | select FB_CFB_IMAGEBLIT | |
f413070e | 2248 | select FB_CFB_REV_PIXELS_IN_BYTE |
979778ff DE |
2249 | select FB_MODE_HELPERS |
2250 | select VIDEOMODE_HELPERS | |
4ed824d9 SR |
2251 | ---help--- |
2252 | This is the frame buffer device driver for the TI LCD controller | |
979778ff | 2253 | found on DA8xx/OMAP-L1xx/AM335x SoCs. |
4ed824d9 SR |
2254 | If unsure, say N. |
2255 | ||
1da177e4 LT |
2256 | config FB_VIRTUAL |
2257 | tristate "Virtual Frame Buffer support (ONLY FOR TESTING!)" | |
2258 | depends on FB | |
87b48849 AD |
2259 | select FB_SYS_FILLRECT |
2260 | select FB_SYS_COPYAREA | |
2261 | select FB_SYS_IMAGEBLIT | |
52102c07 | 2262 | select FB_SYS_FOPS |
1da177e4 LT |
2263 | ---help--- |
2264 | This is a `virtual' frame buffer device. It operates on a chunk of | |
2265 | unswappable kernel memory instead of on the memory of a graphics | |
2266 | board. This means you cannot see any output sent to this frame | |
2267 | buffer device, while it does consume precious memory. The main use | |
2268 | of this frame buffer device is testing and debugging the frame | |
2269 | buffer subsystem. Do NOT enable it for normal systems! To protect | |
2270 | the innocent, it has to be enabled explicitly at boot time using the | |
2271 | kernel option `video=vfb:'. | |
2272 | ||
2273 | To compile this driver as a module, choose M here: the | |
66cf7512 MF |
2274 | module will be called vfb. In order to load it, you must use |
2275 | the vfb_enable=1 option. | |
1da177e4 LT |
2276 | |
2277 | If unsure, say N. | |
e0e34ef7 | 2278 | |
4ee36dc0 MA |
2279 | config XEN_FBDEV_FRONTEND |
2280 | tristate "Xen virtual frame buffer support" | |
2281 | depends on FB && XEN | |
2282 | select FB_SYS_FILLRECT | |
2283 | select FB_SYS_COPYAREA | |
2284 | select FB_SYS_IMAGEBLIT | |
2285 | select FB_SYS_FOPS | |
2286 | select FB_DEFERRED_IO | |
36c1132e | 2287 | select INPUT_XEN_KBDDEV_FRONTEND if INPUT_MISC |
ba69ea42 | 2288 | select XEN_XENBUS_FRONTEND |
4ee36dc0 MA |
2289 | default y |
2290 | help | |
2291 | This driver implements the front-end of the Xen virtual | |
2292 | frame buffer driver. It communicates with a back-end | |
2293 | in another domain. | |
2294 | ||
e9355085 JK |
2295 | config FB_METRONOME |
2296 | tristate "E-Ink Metronome/8track controller support" | |
2297 | depends on FB | |
2298 | select FB_SYS_FILLRECT | |
2299 | select FB_SYS_COPYAREA | |
2300 | select FB_SYS_IMAGEBLIT | |
2301 | select FB_SYS_FOPS | |
2302 | select FB_DEFERRED_IO | |
2303 | help | |
2304 | This driver implements support for the E-Ink Metronome | |
2305 | controller. The pre-release name for this device was 8track | |
2306 | and could also have been called by some vendors as PVI-nnnn. | |
2307 | ||
17a1217e AG |
2308 | config FB_MB862XX |
2309 | tristate "Fujitsu MB862xx GDC support" | |
2310 | depends on FB | |
b9b52cf4 | 2311 | depends on PCI || (OF && PPC) |
17a1217e AG |
2312 | select FB_CFB_FILLRECT |
2313 | select FB_CFB_COPYAREA | |
2314 | select FB_CFB_IMAGEBLIT | |
2315 | ---help--- | |
2316 | Frame buffer driver for Fujitsu Carmine/Coral-P(A)/Lime controllers. | |
2317 | ||
b9b52cf4 BH |
2318 | choice |
2319 | prompt "GDC variant" | |
2320 | depends on FB_MB862XX | |
2321 | ||
17a1217e AG |
2322 | config FB_MB862XX_PCI_GDC |
2323 | bool "Carmine/Coral-P(A) GDC" | |
b9b52cf4 | 2324 | depends on PCI |
17a1217e AG |
2325 | ---help--- |
2326 | This enables framebuffer support for Fujitsu Carmine/Coral-P(A) | |
2327 | PCI graphics controller devices. | |
2328 | ||
2329 | config FB_MB862XX_LIME | |
2330 | bool "Lime GDC" | |
b9b52cf4 | 2331 | depends on OF && PPC |
17a1217e AG |
2332 | select FB_FOREIGN_ENDIAN |
2333 | select FB_LITTLE_ENDIAN | |
2334 | ---help--- | |
2335 | Framebuffer support for Fujitsu Lime GDC on host CPU bus. | |
2336 | ||
b9b52cf4 BH |
2337 | endchoice |
2338 | ||
f8a6b1f4 AG |
2339 | config FB_MB862XX_I2C |
2340 | bool "Support I2C bus on MB862XX GDC" | |
2341 | depends on FB_MB862XX && I2C | |
2342 | default y | |
2343 | help | |
2344 | Selecting this option adds Coral-P(A)/Lime GDC I2C bus adapter | |
2345 | driver to support accessing I2C devices on controller's I2C bus. | |
2346 | These are usually some video decoder chips. | |
2347 | ||
88017bda RM |
2348 | config FB_EP93XX |
2349 | tristate "EP93XX frame buffer support" | |
2350 | depends on FB && ARCH_EP93XX | |
2351 | select FB_CFB_FILLRECT | |
2352 | select FB_CFB_COPYAREA | |
2353 | select FB_CFB_IMAGEBLIT | |
2354 | ---help--- | |
2355 | Framebuffer driver for the Cirrus Logic EP93XX series of processors. | |
2356 | This driver is also available as a module. The module will be called | |
2357 | ep93xx-fb. | |
2358 | ||
17a1217e AG |
2359 | config FB_PRE_INIT_FB |
2360 | bool "Don't reinitialize, use bootloader's GDC/Display configuration" | |
93f40e6f | 2361 | depends on FB && FB_MB862XX_LIME |
17a1217e AG |
2362 | ---help--- |
2363 | Select this option if display contents should be inherited as set by | |
2364 | the bootloader. | |
2365 | ||
d480ace0 | 2366 | config FB_MSM |
4e00dc76 | 2367 | tristate "MSM Framebuffer support" |
d480ace0 PM |
2368 | depends on FB && ARCH_MSM |
2369 | select FB_CFB_FILLRECT | |
2370 | select FB_CFB_COPYAREA | |
2371 | select FB_CFB_IMAGEBLIT | |
d480ace0 | 2372 | |
86528da2 | 2373 | config FB_MX3 |
6e1588cb GL |
2374 | tristate "MX3 Framebuffer support" |
2375 | depends on FB && MX3_IPU | |
2376 | select FB_CFB_FILLRECT | |
2377 | select FB_CFB_COPYAREA | |
2378 | select FB_CFB_IMAGEBLIT | |
2379 | default y | |
2380 | help | |
2381 | This is a framebuffer device for the i.MX31 LCD Controller. So | |
2382 | far only synchronous displays are supported. If you plan to use | |
2383 | an LCD display with your i.MX31 system, say Y here. | |
86528da2 | 2384 | |
0d4ff4df JK |
2385 | config FB_BROADSHEET |
2386 | tristate "E-Ink Broadsheet/Epson S1D13521 controller support" | |
2387 | depends on FB | |
2388 | select FB_SYS_FILLRECT | |
2389 | select FB_SYS_COPYAREA | |
2390 | select FB_SYS_IMAGEBLIT | |
2391 | select FB_SYS_FOPS | |
2392 | select FB_DEFERRED_IO | |
2393 | help | |
2394 | This driver implements support for the E-Ink Broadsheet | |
2395 | controller. The release name for this device was Epson S1D13521 | |
2396 | and could also have been called by other names when coupled with | |
2397 | a bridge adapter. | |
2398 | ||
2c8304d3 HS |
2399 | config FB_AUO_K190X |
2400 | tristate "AUO-K190X EPD controller support" | |
2401 | depends on FB | |
2402 | select FB_SYS_FILLRECT | |
2403 | select FB_SYS_COPYAREA | |
2404 | select FB_SYS_IMAGEBLIT | |
2405 | select FB_SYS_FOPS | |
2406 | select FB_DEFERRED_IO | |
2407 | help | |
2408 | Provides support for epaper controllers from the K190X series | |
2409 | of AUO. These controllers can be used to drive epaper displays | |
2410 | from Sipix. | |
2411 | ||
2412 | This option enables the common support, shared by the individual | |
2413 | controller drivers. You will also have to enable the driver | |
2414 | for the controller type used in your device. | |
2415 | ||
96b1d500 HS |
2416 | config FB_AUO_K1900 |
2417 | tristate "AUO-K1900 EPD controller support" | |
2418 | depends on FB && FB_AUO_K190X | |
2419 | help | |
2420 | This driver implements support for the AUO K1900 epd-controller. | |
2421 | This controller can drive Sipix epaper displays but can only do | |
2422 | serial updates, reducing the number of possible frames per second. | |
2423 | ||
53027cdf HS |
2424 | config FB_AUO_K1901 |
2425 | tristate "AUO-K1901 EPD controller support" | |
2426 | depends on FB && FB_AUO_K190X | |
2427 | help | |
2428 | This driver implements support for the AUO K1901 epd-controller. | |
2429 | This controller can drive Sipix epaper displays and supports | |
2430 | concurrent updates, making higher frames per second possible. | |
2431 | ||
7a92d545 LPC |
2432 | config FB_JZ4740 |
2433 | tristate "JZ4740 LCD framebuffer support" | |
2434 | depends on FB && MACH_JZ4740 | |
2435 | select FB_SYS_FILLRECT | |
2436 | select FB_SYS_COPYAREA | |
2437 | select FB_SYS_IMAGEBLIT | |
2438 | help | |
2439 | Framebuffer support for the JZ4740 SoC. | |
2440 | ||
f0a523b5 SH |
2441 | config FB_MXS |
2442 | tristate "MXS LCD framebuffer support" | |
2443 | depends on FB && ARCH_MXS | |
2444 | select FB_CFB_FILLRECT | |
2445 | select FB_CFB_COPYAREA | |
2446 | select FB_CFB_IMAGEBLIT | |
66940653 | 2447 | select FB_MODE_HELPERS |
d7321df3 | 2448 | select VIDEOMODE_HELPERS |
f0a523b5 SH |
2449 | help |
2450 | Framebuffer support for the MXS SoC. | |
2451 | ||
ce443ab5 G |
2452 | config FB_PUV3_UNIGFX |
2453 | tristate "PKUnity v3 Unigfx framebuffer support" | |
2454 | depends on FB && UNICORE32 && ARCH_PUV3 | |
2455 | select FB_SYS_FILLRECT | |
2456 | select FB_SYS_COPYAREA | |
2457 | select FB_SYS_IMAGEBLIT | |
2458 | select FB_SYS_FOPS | |
2459 | help | |
2460 | Choose this option if you want to use the Unigfx device as a | |
2461 | framebuffer device. Without the support of PCI & AGP. | |
2462 | ||
68a2d20b HZ |
2463 | config FB_HYPERV |
2464 | tristate "Microsoft Hyper-V Synthetic Video support" | |
2465 | depends on FB && HYPERV | |
2466 | select FB_CFB_FILLRECT | |
2467 | select FB_CFB_COPYAREA | |
2468 | select FB_CFB_IMAGEBLIT | |
2469 | help | |
2470 | This framebuffer driver supports Microsoft Hyper-V Synthetic Video. | |
2471 | ||
26549c8d SW |
2472 | config FB_SIMPLE |
2473 | bool "Simple framebuffer support" | |
5ef76da6 | 2474 | depends on (FB = y) |
26549c8d SW |
2475 | select FB_CFB_FILLRECT |
2476 | select FB_CFB_COPYAREA | |
2477 | select FB_CFB_IMAGEBLIT | |
2478 | help | |
2479 | Say Y if you want support for a simple frame-buffer. | |
2480 | ||
2481 | This driver assumes that the display hardware has been initialized | |
2482 | before the kernel boots, and the kernel will simply render to the | |
2483 | pre-allocated frame buffer surface. | |
2484 | ||
2485 | Configuration re: surface address, size, and format must be provided | |
5ef76da6 | 2486 | through device tree, or plain old platform data. |
26549c8d | 2487 | |
f08f3895 | 2488 | source "drivers/video/omap/Kconfig" |
afedec18 | 2489 | source "drivers/video/omap2/Kconfig" |
7258cc14 | 2490 | source "drivers/video/exynos/Kconfig" |
59393bb9 | 2491 | source "drivers/video/mmp/Kconfig" |
179b025f | 2492 | source "drivers/video/backlight/Kconfig" |
179b025f | 2493 | |
1da177e4 LT |
2494 | if VT |
2495 | source "drivers/video/console/Kconfig" | |
2496 | endif | |
2497 | ||
2498 | if FB || SGI_NEWPORT_CONSOLE | |
2499 | source "drivers/video/logo/Kconfig" | |
2500 | endif | |
2501 | ||
f363afc1 KM |
2502 | config FB_SH_MOBILE_MERAM |
2503 | tristate "SuperH Mobile MERAM read ahead support" | |
2504 | depends on (SUPERH || ARCH_SHMOBILE) | |
2505 | select GENERIC_ALLOCATOR | |
2506 | ---help--- | |
2507 | Enable MERAM support for the SuperH controller. | |
2508 | ||
2509 | This will allow for caching of the framebuffer to provide more | |
2510 | reliable access under heavy main memory bus traffic situations. | |
2511 | Up to 4 memory channels can be configured, allowing 4 RGB or | |
2512 | 2 YCbCr framebuffers to be configured. | |
2513 | ||
a2ed00da MR |
2514 | config FB_SSD1307 |
2515 | tristate "Solomon SSD1307 framebuffer support" | |
2516 | depends on FB && I2C | |
2517 | depends on OF | |
76ec9d18 | 2518 | depends on GPIOLIB |
a2ed00da MR |
2519 | select FB_SYS_FOPS |
2520 | select FB_SYS_FILLRECT | |
2521 | select FB_SYS_COPYAREA | |
2522 | select FB_SYS_IMAGEBLIT | |
2523 | select FB_DEFERRED_IO | |
2524 | select PWM | |
2525 | help | |
2526 | This driver implements support for the Solomon SSD1307 | |
2527 | OLED controller over I2C. | |
2528 | ||
1da177e4 | 2529 | endmenu |