[mirror_qemu.git] / hw / char / bcm2835_aux.c

/*
 * BCM2835 (Raspberry Pi / Pi 2) Aux block (mini UART and SPI).
 * Copyright (c) 2015, Microsoft
 * Written by Andrew Baumann
 * Based on pl011.c, copyright terms below:
 *
 * Arm PrimeCell PL011 UART
 *
 * Copyright (c) 2006 CodeSourcery.
 * Written by Paul Brook
 *
 * This code is licensed under the GPL.
 *
 * At present only the core UART functions (data path for tx/rx) are
 * implemented. The following features/registers are unimplemented:
 *  - Line/modem control
 *  - Scratch register
 *  - Extra control
 *  - Baudrate
 *  - SPI interfaces
 */

#include "qemu/osdep.h"
#include "hw/char/bcm2835_aux.h"
#include "qemu/log.h"

#define AUX_IRQ         0x0
#define AUX_ENABLES     0x4
#define AUX_MU_IO_REG   0x40
#define AUX_MU_IER_REG  0x44
#define AUX_MU_IIR_REG  0x48
#define AUX_MU_LCR_REG  0x4c
#define AUX_MU_MCR_REG  0x50
#define AUX_MU_LSR_REG  0x54
#define AUX_MU_MSR_REG  0x58
#define AUX_MU_SCRATCH  0x5c
#define AUX_MU_CNTL_REG 0x60
#define AUX_MU_STAT_REG 0x64
#define AUX_MU_BAUD_REG 0x68

/* bits in IER/IIR registers */
#define RX_INT  0x1
#define TX_INT  0x2

static void bcm2835_aux_update(BCM2835AuxState *s)
{
    /* signal an interrupt if either:
     * 1. rx interrupt is enabled and we have a non-empty rx fifo, or
     * 2. the tx interrupt is enabled (since we instantly drain the tx fifo)
     */
    s->iir = 0;
    if ((s->ier & RX_INT) && s->read_count != 0) {
        s->iir |= RX_INT;
    }
    if (s->ier & TX_INT) {
        s->iir |= TX_INT;
    }
    qemu_set_irq(s->irq, s->iir != 0);
}

static uint64_t bcm2835_aux_read(void *opaque, hwaddr offset, unsigned size)
{
    BCM2835AuxState *s = opaque;
    uint32_t c, res;

    switch (offset) {
    case AUX_IRQ:
        return s->iir != 0;

    case AUX_ENABLES:
        return 1; /* mini UART permanently enabled */

    case AUX_MU_IO_REG:
        /* "DLAB bit set means access baudrate register" is NYI */
        c = s->read_fifo[s->read_pos];
        if (s->read_count > 0) {
            s->read_count--;
            if (++s->read_pos == BCM2835_AUX_RX_FIFO_LEN) {
                s->read_pos = 0;
            }
        }
        qemu_chr_fe_accept_input(&s->chr);
        bcm2835_aux_update(s);
        return c;

    case AUX_MU_IER_REG:
        /* "DLAB bit set means access baudrate register" is NYI */
        return 0xc0 | s->ier; /* FIFO enables always read 1 */

    case AUX_MU_IIR_REG:
        res = 0xc0; /* FIFO enables */
        /* The spec is unclear on what happens when both tx and rx
         * interrupts are active, besides that this cannot occur. At
         * present, we choose to prioritise the rx interrupt, since
         * the tx fifo is always empty. */
        if (s->read_count != 0) {
            res |= 0x4;
        } else {
            res |= 0x2;
        }
        if (s->iir == 0) {
            res |= 0x1;
        }
        return res;

    case AUX_MU_LCR_REG:
        qemu_log_mask(LOG_UNIMP, "%s: AUX_MU_LCR_REG unsupported\n", __func__);
        return 0;

    case AUX_MU_MCR_REG:
        qemu_log_mask(LOG_UNIMP, "%s: AUX_MU_MCR_REG unsupported\n", __func__);
        return 0;

    case AUX_MU_LSR_REG:
        res = 0x60; /* tx idle, empty */
        if (s->read_count != 0) {
            res |= 0x1;
        }
        return res;

    case AUX_MU_MSR_REG:
        qemu_log_mask(LOG_UNIMP, "%s: AUX_MU_MSR_REG unsupported\n", __func__);
        return 0;

    case AUX_MU_SCRATCH:
        qemu_log_mask(LOG_UNIMP, "%s: AUX_MU_SCRATCH unsupported\n", __func__);
        return 0;

    case AUX_MU_CNTL_REG:
        return 0x3; /* tx, rx enabled */

    case AUX_MU_STAT_REG:
        res = 0x30e; /* space in the output buffer, empty tx fifo, idle tx/rx */
        if (s->read_count > 0) {
            res |= 0x1; /* data in input buffer */
            assert(s->read_count < BCM2835_AUX_RX_FIFO_LEN);
            res |= ((uint32_t)s->read_count) << 16; /* rx fifo fill level */
        }
        return res;

    case AUX_MU_BAUD_REG:
        qemu_log_mask(LOG_UNIMP, "%s: AUX_MU_BAUD_REG unsupported\n", __func__);
        return 0;

    default:
        qemu_log_mask(LOG_GUEST_ERROR, "%s: Bad offset %"HWADDR_PRIx"\n",
                      __func__, offset);
        return 0;
    }
}

static void bcm2835_aux_write(void *opaque, hwaddr offset, uint64_t value,
                              unsigned size)
{
    BCM2835AuxState *s = opaque;
    unsigned char ch;

    switch (offset) {
    case AUX_ENABLES:
        if (value != 1) {
            qemu_log_mask(LOG_UNIMP, "%s: unsupported attempt to enable SPI "
                          "or disable UART\n", __func__);
        }
        break;

    case AUX_MU_IO_REG:
        /* "DLAB bit set means access baudrate register" is NYI */
        ch = value;
        /* XXX this blocks entire thread. Rewrite to use
         * qemu_chr_fe_write and background I/O callbacks */
        qemu_chr_fe_write_all(&s->chr, &ch, 1);
        break;

    case AUX_MU_IER_REG:
        /* "DLAB bit set means access baudrate register" is NYI */
        s->ier = value & (TX_INT | RX_INT);
        bcm2835_aux_update(s);
        break;

    case AUX_MU_IIR_REG:
        if (value & 0x2) {
            s->read_count = 0;
        }
        break;

    case AUX_MU_LCR_REG:
        qemu_log_mask(LOG_UNIMP, "%s: AUX_MU_LCR_REG unsupported\n", __func__);
        break;

    case AUX_MU_MCR_REG:
        qemu_log_mask(LOG_UNIMP, "%s: AUX_MU_MCR_REG unsupported\n", __func__);
        break;

    case AUX_MU_SCRATCH:
        qemu_log_mask(LOG_UNIMP, "%s: AUX_MU_SCRATCH unsupported\n", __func__);
        break;

    case AUX_MU_CNTL_REG:
        qemu_log_mask(LOG_UNIMP, "%s: AUX_MU_CNTL_REG unsupported\n", __func__);
        break;

    case AUX_MU_BAUD_REG:
        qemu_log_mask(LOG_UNIMP, "%s: AUX_MU_BAUD_REG unsupported\n", __func__);
        break;

    default:
        qemu_log_mask(LOG_GUEST_ERROR, "%s: Bad offset %"HWADDR_PRIx"\n",
                      __func__, offset);
    }

    bcm2835_aux_update(s);
}

static int bcm2835_aux_can_receive(void *opaque)
{
    BCM2835AuxState *s = opaque;

    return s->read_count < BCM2835_AUX_RX_FIFO_LEN;
}

static void bcm2835_aux_put_fifo(void *opaque, uint8_t value)
{
    BCM2835AuxState *s = opaque;
    int slot;

    slot = s->read_pos + s->read_count;
    if (slot >= BCM2835_AUX_RX_FIFO_LEN) {
        slot -= BCM2835_AUX_RX_FIFO_LEN;
    }
    s->read_fifo[slot] = value;
    s->read_count++;
    if (s->read_count == BCM2835_AUX_RX_FIFO_LEN) {
        /* buffer full */
    }
    bcm2835_aux_update(s);
}

static void bcm2835_aux_receive(void *opaque, const uint8_t *buf, int size)
{
    bcm2835_aux_put_fifo(opaque, *buf);
}

static const MemoryRegionOps bcm2835_aux_ops = {
    .read = bcm2835_aux_read,
    .write = bcm2835_aux_write,
    .endianness = DEVICE_NATIVE_ENDIAN,
    .valid.min_access_size = 4,
    .valid.max_access_size = 4,
};

static const VMStateDescription vmstate_bcm2835_aux = {
    .name = TYPE_BCM2835_AUX,
    .version_id = 1,
    .minimum_version_id = 1,
    .fields = (VMStateField[]) {
        VMSTATE_UINT8_ARRAY(read_fifo, BCM2835AuxState,
                            BCM2835_AUX_RX_FIFO_LEN),
        VMSTATE_UINT8(read_pos, BCM2835AuxState),
        VMSTATE_UINT8(read_count, BCM2835AuxState),
        VMSTATE_UINT8(ier, BCM2835AuxState),
        VMSTATE_UINT8(iir, BCM2835AuxState),
        VMSTATE_END_OF_LIST()
    }
};

static void bcm2835_aux_init(Object *obj)
{
    SysBusDevice *sbd = SYS_BUS_DEVICE(obj);
    BCM2835AuxState *s = BCM2835_AUX(obj);

    memory_region_init_io(&s->iomem, OBJECT(s), &bcm2835_aux_ops, s,
                          TYPE_BCM2835_AUX, 0x100);
    sysbus_init_mmio(sbd, &s->iomem);
    sysbus_init_irq(sbd, &s->irq);
}

static void bcm2835_aux_realize(DeviceState *dev, Error **errp)
{
    BCM2835AuxState *s = BCM2835_AUX(dev);

    qemu_chr_fe_set_handlers(&s->chr, bcm2835_aux_can_receive,
                             bcm2835_aux_receive, NULL, NULL, s, NULL, true);
}

static Property bcm2835_aux_props[] = {
    DEFINE_PROP_CHR("chardev", BCM2835AuxState, chr),
    DEFINE_PROP_END_OF_LIST(),
};

static void bcm2835_aux_class_init(ObjectClass *oc, void *data)
{
    DeviceClass *dc = DEVICE_CLASS(oc);

    dc->realize = bcm2835_aux_realize;
    dc->vmsd = &vmstate_bcm2835_aux;
    set_bit(DEVICE_CATEGORY_INPUT, dc->categories);
    dc->props = bcm2835_aux_props;
}

static const TypeInfo bcm2835_aux_info = {
    .name          = TYPE_BCM2835_AUX,
    .parent        = TYPE_SYS_BUS_DEVICE,
    .instance_size = sizeof(BCM2835AuxState),
    .instance_init = bcm2835_aux_init,
    .class_init    = bcm2835_aux_class_init,
};

static void bcm2835_aux_register_types(void)
{
    type_register_static(&bcm2835_aux_info);
}

type_init(bcm2835_aux_register_types)
Commit	Line	Data
97398d90 AB	1	/*
	2	* BCM2835 (Raspberry Pi / Pi 2) Aux block (mini UART and SPI).
	3	* Copyright (c) 2015, Microsoft
	4	* Written by Andrew Baumann
	5	* Based on pl011.c, copyright terms below:
	6	*
	7	* Arm PrimeCell PL011 UART
	8	*
	9	* Copyright (c) 2006 CodeSourcery.
	10	* Written by Paul Brook
	11	*
	12	* This code is licensed under the GPL.
	13	*
	14	* At present only the core UART functions (data path for tx/rx) are
	15	* implemented. The following features/registers are unimplemented:
	16	* - Line/modem control
	17	* - Scratch register
	18	* - Extra control
	19	* - Baudrate
	20	* - SPI interfaces
	21	*/
	22
	23	#include "qemu/osdep.h"
	24	#include "hw/char/bcm2835_aux.h"
03dd024f	25	#include "qemu/log.h"
97398d90 AB	26
	27	#define AUX_IRQ 0x0
	28	#define AUX_ENABLES 0x4
	29	#define AUX_MU_IO_REG 0x40
	30	#define AUX_MU_IER_REG 0x44
	31	#define AUX_MU_IIR_REG 0x48
	32	#define AUX_MU_LCR_REG 0x4c
	33	#define AUX_MU_MCR_REG 0x50
	34	#define AUX_MU_LSR_REG 0x54
	35	#define AUX_MU_MSR_REG 0x58
	36	#define AUX_MU_SCRATCH 0x5c
	37	#define AUX_MU_CNTL_REG 0x60
	38	#define AUX_MU_STAT_REG 0x64
	39	#define AUX_MU_BAUD_REG 0x68
	40
	41	/* bits in IER/IIR registers */
65e9f27f GR	42	#define RX_INT 0x1
65e9f27f GR	43	#define TX_INT 0x2
97398d90 AB	44
	45	static void bcm2835_aux_update(BCM2835AuxState *s)
	46	{
	47	/* signal an interrupt if either:
	48	* 1. rx interrupt is enabled and we have a non-empty rx fifo, or
	49	* 2. the tx interrupt is enabled (since we instantly drain the tx fifo)
	50	*/
	51	s->iir = 0;
	52	if ((s->ier & RX_INT) && s->read_count != 0) {
	53	s->iir \|= RX_INT;
	54	}
	55	if (s->ier & TX_INT) {
	56	s->iir \|= TX_INT;
	57	}
	58	qemu_set_irq(s->irq, s->iir != 0);
	59	}
	60
	61	static uint64_t bcm2835_aux_read(void *opaque, hwaddr offset, unsigned size)
	62	{
	63	BCM2835AuxState *s = opaque;
	64	uint32_t c, res;
	65
	66	switch (offset) {
	67	case AUX_IRQ:
	68	return s->iir != 0;
	69
	70	case AUX_ENABLES:
	71	return 1; /* mini UART permanently enabled */
	72
	73	case AUX_MU_IO_REG:
	74	/* "DLAB bit set means access baudrate register" is NYI */
	75	c = s->read_fifo[s->read_pos];
	76	if (s->read_count > 0) {
	77	s->read_count--;
	78	if (++s->read_pos == BCM2835_AUX_RX_FIFO_LEN) {
	79	s->read_pos = 0;
	80	}
	81	}
fa394ed6	82	qemu_chr_fe_accept_input(&s->chr);
97398d90 AB	83	bcm2835_aux_update(s);
	84	return c;
	85
	86	case AUX_MU_IER_REG:
	87	/* "DLAB bit set means access baudrate register" is NYI */
	88	return 0xc0 \| s->ier; /* FIFO enables always read 1 */
	89
	90	case AUX_MU_IIR_REG:
	91	res = 0xc0; /* FIFO enables */
	92	/* The spec is unclear on what happens when both tx and rx
	93	* interrupts are active, besides that this cannot occur. At
	94	* present, we choose to prioritise the rx interrupt, since
	95	* the tx fifo is always empty. */
	96	if (s->read_count != 0) {
	97	res \|= 0x4;
	98	} else {
	99	res \|= 0x2;
	100	}
	101	if (s->iir == 0) {
	102	res \|= 0x1;
	103	}
	104	return res;
	105
	106	case AUX_MU_LCR_REG:
	107	qemu_log_mask(LOG_UNIMP, "%s: AUX_MU_LCR_REG unsupported\n", __func__);
	108	return 0;
	109
	110	case AUX_MU_MCR_REG:
	111	qemu_log_mask(LOG_UNIMP, "%s: AUX_MU_MCR_REG unsupported\n", __func__);
	112	return 0;
	113
	114	case AUX_MU_LSR_REG:
	115	res = 0x60; /* tx idle, empty */
	116	if (s->read_count != 0) {
	117	res \|= 0x1;
	118	}
	119	return res;
	120
	121	case AUX_MU_MSR_REG:
	122	qemu_log_mask(LOG_UNIMP, "%s: AUX_MU_MSR_REG unsupported\n", __func__);
	123	return 0;
	124
	125	case AUX_MU_SCRATCH:
	126	qemu_log_mask(LOG_UNIMP, "%s: AUX_MU_SCRATCH unsupported\n", __func__);
	127	return 0;
	128
	129	case AUX_MU_CNTL_REG:
	130	return 0x3; /* tx, rx enabled */
	131
	132	case AUX_MU_STAT_REG:
	133	res = 0x30e; /* space in the output buffer, empty tx fifo, idle tx/rx */
	134	if (s->read_count > 0) {
	135	res \|= 0x1; /* data in input buffer */
	136	assert(s->read_count < BCM2835_AUX_RX_FIFO_LEN);
	137	res \|= ((uint32_t)s->read_count) << 16; /* rx fifo fill level */
	138	}
	139	return res;
	140
	141	case AUX_MU_BAUD_REG:
	142	qemu_log_mask(LOG_UNIMP, "%s: AUX_MU_BAUD_REG unsupported\n", __func__);
	143	return 0;
	144
	145	default:
	146	qemu_log_mask(LOG_GUEST_ERROR, "%s: Bad offset %"HWADDR_PRIx"\n",
147	__func__, offset);
148	return 0;
149	}
150	}
151
152	static void bcm2835_aux_write(void *opaque, hwaddr offset, uint64_t value,
153	unsigned size)
154	{
155	BCM2835AuxState *s = opaque;
156	unsigned char ch;
157
158	switch (offset) {
159	case AUX_ENABLES:
160	if (value != 1) {
161	qemu_log_mask(LOG_UNIMP, "%s: unsupported attempt to enable SPI "
162	"or disable UART\n", __func__);
163	}
164	break;
165
166	case AUX_MU_IO_REG:
167	/* "DLAB bit set means access baudrate register" is NYI */
168	ch = value;
fa394ed6 MAL	169	/* XXX this blocks entire thread. Rewrite to use
	170	* qemu_chr_fe_write and background I/O callbacks */
	171	qemu_chr_fe_write_all(&s->chr, &ch, 1);
97398d90 AB	172	break;
	173
	174	case AUX_MU_IER_REG:
	175	/* "DLAB bit set means access baudrate register" is NYI */
	176	s->ier = value & (TX_INT \| RX_INT);
	177	bcm2835_aux_update(s);
	178	break;
	179
	180	case AUX_MU_IIR_REG:
	181	if (value & 0x2) {
	182	s->read_count = 0;
	183	}
	184	break;
	185
	186	case AUX_MU_LCR_REG:
	187	qemu_log_mask(LOG_UNIMP, "%s: AUX_MU_LCR_REG unsupported\n", __func__);
	188	break;
	189
	190	case AUX_MU_MCR_REG:
	191	qemu_log_mask(LOG_UNIMP, "%s: AUX_MU_MCR_REG unsupported\n", __func__);
	192	break;
	193
	194	case AUX_MU_SCRATCH:
	195	qemu_log_mask(LOG_UNIMP, "%s: AUX_MU_SCRATCH unsupported\n", __func__);
	196	break;
	197
	198	case AUX_MU_CNTL_REG:
	199	qemu_log_mask(LOG_UNIMP, "%s: AUX_MU_CNTL_REG unsupported\n", __func__);
	200	break;
	201
	202	case AUX_MU_BAUD_REG:
	203	qemu_log_mask(LOG_UNIMP, "%s: AUX_MU_BAUD_REG unsupported\n", __func__);
	204	break;
	205
	206	default:
	207	qemu_log_mask(LOG_GUEST_ERROR, "%s: Bad offset %"HWADDR_PRIx"\n",
	208	__func__, offset);
	209	}
	210
	211	bcm2835_aux_update(s);
	212	}
	213
	214	static int bcm2835_aux_can_receive(void *opaque)
	215	{
	216	BCM2835AuxState *s = opaque;
	217
	218	return s->read_count < BCM2835_AUX_RX_FIFO_LEN;
	219	}
	220
	221	static void bcm2835_aux_put_fifo(void *opaque, uint8_t value)
	222	{
	223	BCM2835AuxState *s = opaque;
	224	int slot;
	225
	226	slot = s->read_pos + s->read_count;
	227	if (slot >= BCM2835_AUX_RX_FIFO_LEN) {
	228	slot -= BCM2835_AUX_RX_FIFO_LEN;
	229	}
	230	s->read_fifo[slot] = value;
	231	s->read_count++;
	232	if (s->read_count == BCM2835_AUX_RX_FIFO_LEN) {
	233	/* buffer full */
	234	}
	235	bcm2835_aux_update(s);
236	}
237
238	static void bcm2835_aux_receive(void opaque, const uint8_t buf, int size)
239	{
240	bcm2835_aux_put_fifo(opaque, *buf);
241	}
242
243	static const MemoryRegionOps bcm2835_aux_ops = {
244	.read = bcm2835_aux_read,
245	.write = bcm2835_aux_write,
246	.endianness = DEVICE_NATIVE_ENDIAN,
247	.valid.min_access_size = 4,
248	.valid.max_access_size = 4,
249	};
250
251	static const VMStateDescription vmstate_bcm2835_aux = {
252	.name = TYPE_BCM2835_AUX,
253	.version_id = 1,
254	.minimum_version_id = 1,
255	.fields = (VMStateField[]) {
256	VMSTATE_UINT8_ARRAY(read_fifo, BCM2835AuxState,
257	BCM2835_AUX_RX_FIFO_LEN),
258	VMSTATE_UINT8(read_pos, BCM2835AuxState),
259	VMSTATE_UINT8(read_count, BCM2835AuxState),
260	VMSTATE_UINT8(ier, BCM2835AuxState),
261	VMSTATE_UINT8(iir, BCM2835AuxState),
262	VMSTATE_END_OF_LIST()
263	}
264	};
265
266	static void bcm2835_aux_init(Object *obj)
267	{
268	SysBusDevice *sbd = SYS_BUS_DEVICE(obj);
269	BCM2835AuxState *s = BCM2835_AUX(obj);
270
271	memory_region_init_io(&s->iomem, OBJECT(s), &bcm2835_aux_ops, s,
272	TYPE_BCM2835_AUX, 0x100);
273	sysbus_init_mmio(sbd, &s->iomem);
274	sysbus_init_irq(sbd, &s->irq);
275	}
276
277	static void bcm2835_aux_realize(DeviceState dev, Error *errp)
278	{
279	BCM2835AuxState *s = BCM2835_AUX(dev);
280
fa394ed6	281	qemu_chr_fe_set_handlers(&s->chr, bcm2835_aux_can_receive,
81517ba3	282	bcm2835_aux_receive, NULL, NULL, s, NULL, true);
97398d90 AB	283	}
	284
	285	static Property bcm2835_aux_props[] = {
	286	DEFINE_PROP_CHR("chardev", BCM2835AuxState, chr),
	287	DEFINE_PROP_END_OF_LIST(),
	288	};
	289
	290	static void bcm2835_aux_class_init(ObjectClass oc, void data)
	291	{
	292	DeviceClass *dc = DEVICE_CLASS(oc);
	293
	294	dc->realize = bcm2835_aux_realize;
	295	dc->vmsd = &vmstate_bcm2835_aux;
	296	set_bit(DEVICE_CATEGORY_INPUT, dc->categories);
	297	dc->props = bcm2835_aux_props;
	298	}
	299
	300	static const TypeInfo bcm2835_aux_info = {
	301	.name = TYPE_BCM2835_AUX,
	302	.parent = TYPE_SYS_BUS_DEVICE,
	303	.instance_size = sizeof(BCM2835AuxState),
	304	.instance_init = bcm2835_aux_init,
	305	.class_init = bcm2835_aux_class_init,
	306	};
	307
	308	static void bcm2835_aux_register_types(void)
	309	{
	310	type_register_static(&bcm2835_aux_info);
	311	}
	312
	313	type_init(bcm2835_aux_register_types)