]>
Commit | Line | Data |
---|---|---|
1da177e4 LT |
1 | /* |
2 | * This file is subject to the terms and conditions of the GNU General Public | |
3 | * License. See the file "COPYING" in the main directory of this archive | |
4 | * for more details. | |
5 | * | |
6 | * hpc3.h: Definitions for SGI HPC3 controller | |
7 | * | |
8 | * Copyright (C) 1996 David S. Miller | |
9 | * Copyright (C) 1998 Ralf Baechle | |
10 | */ | |
11 | ||
12 | #ifndef _SGI_HPC3_H | |
13 | #define _SGI_HPC3_H | |
14 | ||
15 | #include <linux/types.h> | |
16 | #include <asm/page.h> | |
17 | ||
18 | /* An HPC DMA descriptor. */ | |
19 | struct hpc_dma_desc { | |
20 | u32 pbuf; /* physical address of data buffer */ | |
21 | u32 cntinfo; /* counter and info bits */ | |
22 | #define HPCDMA_EOX 0x80000000 /* last desc in chain for tx */ | |
23 | #define HPCDMA_EOR 0x80000000 /* last desc in chain for rx */ | |
24 | #define HPCDMA_EOXP 0x40000000 /* end of packet for tx */ | |
25 | #define HPCDMA_EORP 0x40000000 /* end of packet for rx */ | |
26 | #define HPCDMA_XIE 0x20000000 /* irq generated when at end of this desc */ | |
27 | #define HPCDMA_XIU 0x01000000 /* Tx buffer in use by CPU. */ | |
28 | #define HPCDMA_EIPC 0x00ff0000 /* SEEQ ethernet special xternal bytecount */ | |
29 | #define HPCDMA_ETXD 0x00008000 /* set to one by HPC when packet tx'd */ | |
30 | #define HPCDMA_OWN 0x00004000 /* Denotes ring buffer ownership on rx */ | |
31 | #define HPCDMA_BCNT 0x00003fff /* size in bytes of this dma buffer */ | |
32 | ||
33 | u32 pnext; /* paddr of next hpc_dma_desc if any */ | |
34 | }; | |
35 | ||
36 | /* The set of regs for each HPC3 PBUS DMA channel. */ | |
37 | struct hpc3_pbus_dmacregs { | |
38 | volatile u32 pbdma_bptr; /* pbus dma channel buffer ptr */ | |
39 | volatile u32 pbdma_dptr; /* pbus dma channel desc ptr */ | |
40 | u32 _unused0[0x1000/4 - 2]; /* padding */ | |
41 | volatile u32 pbdma_ctrl; /* pbus dma channel control register has | |
42 | * copletely different meaning for read | |
43 | * compared with write */ | |
44 | /* read */ | |
45 | #define HPC3_PDMACTRL_INT 0x00000001 /* interrupt (cleared after read) */ | |
46 | #define HPC3_PDMACTRL_ISACT 0x00000002 /* channel active */ | |
47 | /* write */ | |
48 | #define HPC3_PDMACTRL_SEL 0x00000002 /* little endian transfer */ | |
49 | #define HPC3_PDMACTRL_RCV 0x00000004 /* direction is receive */ | |
50 | #define HPC3_PDMACTRL_FLSH 0x00000008 /* enable flush for receive DMA */ | |
51 | #define HPC3_PDMACTRL_ACT 0x00000010 /* start dma transfer */ | |
52 | #define HPC3_PDMACTRL_LD 0x00000020 /* load enable for ACT */ | |
53 | #define HPC3_PDMACTRL_RT 0x00000040 /* Use realtime GIO bus servicing */ | |
54 | #define HPC3_PDMACTRL_HW 0x0000ff00 /* DMA High-water mark */ | |
55 | #define HPC3_PDMACTRL_FB 0x003f0000 /* Ptr to beginning of fifo */ | |
56 | #define HPC3_PDMACTRL_FE 0x3f000000 /* Ptr to end of fifo */ | |
57 | ||
58 | u32 _unused1[0x1000/4 - 1]; /* padding */ | |
59 | }; | |
60 | ||
61 | /* The HPC3 SCSI registers, this does not include external ones. */ | |
62 | struct hpc3_scsiregs { | |
63 | volatile u32 cbptr; /* current dma buffer ptr, diagnostic use only */ | |
64 | volatile u32 ndptr; /* next dma descriptor ptr */ | |
65 | u32 _unused0[0x1000/4 - 2]; /* padding */ | |
66 | volatile u32 bcd; /* byte count info */ | |
67 | #define HPC3_SBCD_BCNTMSK 0x00003fff /* bytes to transfer from/to memory */ | |
68 | #define HPC3_SBCD_XIE 0x00004000 /* Send IRQ when done with cur buf */ | |
69 | #define HPC3_SBCD_EOX 0x00008000 /* Indicates this is last buf in chain */ | |
70 | ||
71 | volatile u32 ctrl; /* control register */ | |
72 | #define HPC3_SCTRL_IRQ 0x01 /* IRQ asserted, either dma done or parity */ | |
73 | #define HPC3_SCTRL_ENDIAN 0x02 /* DMA endian mode, 0=big 1=little */ | |
74 | #define HPC3_SCTRL_DIR 0x04 /* DMA direction, 1=dev2mem 0=mem2dev */ | |
75 | #define HPC3_SCTRL_FLUSH 0x08 /* Tells HPC3 to flush scsi fifos */ | |
76 | #define HPC3_SCTRL_ACTIVE 0x10 /* SCSI DMA channel is active */ | |
77 | #define HPC3_SCTRL_AMASK 0x20 /* DMA active inhibits PIO */ | |
78 | #define HPC3_SCTRL_CRESET 0x40 /* Resets dma channel and external controller */ | |
79 | #define HPC3_SCTRL_PERR 0x80 /* Bad parity on HPC3 iface to scsi controller */ | |
80 | ||
81 | volatile u32 gfptr; /* current GIO fifo ptr */ | |
82 | volatile u32 dfptr; /* current device fifo ptr */ | |
83 | volatile u32 dconfig; /* DMA configuration register */ | |
84 | #define HPC3_SDCFG_HCLK 0x00001 /* Enable DMA half clock mode */ | |
85 | #define HPC3_SDCFG_D1 0x00006 /* Cycles to spend in D1 state */ | |
86 | #define HPC3_SDCFG_D2 0x00038 /* Cycles to spend in D2 state */ | |
87 | #define HPC3_SDCFG_D3 0x001c0 /* Cycles to spend in D3 state */ | |
88 | #define HPC3_SDCFG_HWAT 0x00e00 /* DMA high water mark */ | |
89 | #define HPC3_SDCFG_HW 0x01000 /* Enable 16-bit halfword DMA accesses to scsi */ | |
90 | #define HPC3_SDCFG_SWAP 0x02000 /* Byte swap all DMA accesses */ | |
91 | #define HPC3_SDCFG_EPAR 0x04000 /* Enable parity checking for DMA */ | |
92 | #define HPC3_SDCFG_POLL 0x08000 /* hd_dreq polarity control */ | |
93 | #define HPC3_SDCFG_ERLY 0x30000 /* hd_dreq behavior control bits */ | |
94 | ||
95 | volatile u32 pconfig; /* PIO configuration register */ | |
96 | #define HPC3_SPCFG_P3 0x0003 /* Cycles to spend in P3 state */ | |
97 | #define HPC3_SPCFG_P2W 0x001c /* Cycles to spend in P2 state for writes */ | |
98 | #define HPC3_SPCFG_P2R 0x01e0 /* Cycles to spend in P2 state for reads */ | |
99 | #define HPC3_SPCFG_P1 0x0e00 /* Cycles to spend in P1 state */ | |
100 | #define HPC3_SPCFG_HW 0x1000 /* Enable 16-bit halfword PIO accesses to scsi */ | |
101 | #define HPC3_SPCFG_SWAP 0x2000 /* Byte swap all PIO accesses */ | |
102 | #define HPC3_SPCFG_EPAR 0x4000 /* Enable parity checking for PIO */ | |
103 | #define HPC3_SPCFG_FUJI 0x8000 /* Fujitsu scsi controller mode for faster dma/pio */ | |
104 | ||
105 | u32 _unused1[0x1000/4 - 6]; /* padding */ | |
106 | }; | |
107 | ||
108 | /* SEEQ ethernet HPC3 registers, only one seeq per HPC3. */ | |
109 | struct hpc3_ethregs { | |
110 | /* Receiver registers. */ | |
111 | volatile u32 rx_cbptr; /* current dma buffer ptr, diagnostic use only */ | |
112 | volatile u32 rx_ndptr; /* next dma descriptor ptr */ | |
113 | u32 _unused0[0x1000/4 - 2]; /* padding */ | |
114 | volatile u32 rx_bcd; /* byte count info */ | |
115 | #define HPC3_ERXBCD_BCNTMSK 0x00003fff /* bytes to be sent to memory */ | |
116 | #define HPC3_ERXBCD_XIE 0x20000000 /* HPC3 interrupts cpu at end of this buf */ | |
117 | #define HPC3_ERXBCD_EOX 0x80000000 /* flags this as end of descriptor chain */ | |
118 | ||
119 | volatile u32 rx_ctrl; /* control register */ | |
120 | #define HPC3_ERXCTRL_STAT50 0x0000003f /* Receive status reg bits of Seeq8003 */ | |
121 | #define HPC3_ERXCTRL_STAT6 0x00000040 /* Rdonly irq status */ | |
122 | #define HPC3_ERXCTRL_STAT7 0x00000080 /* Rdonlt old/new status bit from Seeq */ | |
123 | #define HPC3_ERXCTRL_ENDIAN 0x00000100 /* Endian for dma channel, little=1 big=0 */ | |
124 | #define HPC3_ERXCTRL_ACTIVE 0x00000200 /* Tells if DMA transfer is in progress */ | |
125 | #define HPC3_ERXCTRL_AMASK 0x00000400 /* Tells if ACTIVE inhibits PIO's to hpc3 */ | |
126 | #define HPC3_ERXCTRL_RBO 0x00000800 /* Receive buffer overflow if set to 1 */ | |
127 | ||
128 | volatile u32 rx_gfptr; /* current GIO fifo ptr */ | |
129 | volatile u32 rx_dfptr; /* current device fifo ptr */ | |
130 | u32 _unused1; /* padding */ | |
302a5c4b RB |
131 | volatile u32 reset; /* reset register */ |
132 | #define HPC3_ERST_CRESET 0x1 /* Reset dma channel and external controller */ | |
133 | #define HPC3_ERST_CLRIRQ 0x2 /* Clear channel interrupt */ | |
134 | #define HPC3_ERST_LBACK 0x4 /* Enable diagnostic loopback mode of Seeq8003 */ | |
135 | ||
136 | volatile u32 dconfig; /* DMA configuration register */ | |
137 | #define HPC3_EDCFG_D1 0x0000f /* Cycles to spend in D1 state for PIO */ | |
138 | #define HPC3_EDCFG_D2 0x000f0 /* Cycles to spend in D2 state for PIO */ | |
139 | #define HPC3_EDCFG_D3 0x00f00 /* Cycles to spend in D3 state for PIO */ | |
140 | #define HPC3_EDCFG_WCTRL 0x01000 /* Enable writes of desc into ex ctrl port */ | |
141 | #define HPC3_EDCFG_FRXDC 0x02000 /* Clear eop stat bits upon rxdc, hw seeq fix */ | |
142 | #define HPC3_EDCFG_FEOP 0x04000 /* Bad packet marker timeout enable */ | |
143 | #define HPC3_EDCFG_FIRQ 0x08000 /* Another bad packet timeout enable */ | |
144 | #define HPC3_EDCFG_PTO 0x30000 /* Programmed timeout value for above two */ | |
145 | ||
146 | volatile u32 pconfig; /* PIO configuration register */ | |
147 | #define HPC3_EPCFG_P1 0x000f /* Cycles to spend in P1 state for PIO */ | |
148 | #define HPC3_EPCFG_P2 0x00f0 /* Cycles to spend in P2 state for PIO */ | |
149 | #define HPC3_EPCFG_P3 0x0f00 /* Cycles to spend in P3 state for PIO */ | |
150 | #define HPC3_EPCFG_TST 0x1000 /* Diagnistic ram test feature bit */ | |
1da177e4 LT |
151 | |
152 | u32 _unused2[0x1000/4 - 8]; /* padding */ | |
153 | ||
154 | /* Transmitter registers. */ | |
155 | volatile u32 tx_cbptr; /* current dma buffer ptr, diagnostic use only */ | |
156 | volatile u32 tx_ndptr; /* next dma descriptor ptr */ | |
157 | u32 _unused3[0x1000/4 - 2]; /* padding */ | |
158 | volatile u32 tx_bcd; /* byte count info */ | |
159 | #define HPC3_ETXBCD_BCNTMSK 0x00003fff /* bytes to be read from memory */ | |
160 | #define HPC3_ETXBCD_ESAMP 0x10000000 /* if set, too late to add descriptor */ | |
161 | #define HPC3_ETXBCD_XIE 0x20000000 /* Interrupt cpu at end of cur desc */ | |
162 | #define HPC3_ETXBCD_EOP 0x40000000 /* Last byte of cur buf is end of packet */ | |
163 | #define HPC3_ETXBCD_EOX 0x80000000 /* This buf is the end of desc chain */ | |
164 | ||
165 | volatile u32 tx_ctrl; /* control register */ | |
166 | #define HPC3_ETXCTRL_STAT30 0x0000000f /* Rdonly copy of seeq tx stat reg */ | |
167 | #define HPC3_ETXCTRL_STAT4 0x00000010 /* Indicate late collision occurred */ | |
168 | #define HPC3_ETXCTRL_STAT75 0x000000e0 /* Rdonly irq status from seeq */ | |
169 | #define HPC3_ETXCTRL_ENDIAN 0x00000100 /* DMA channel endian mode, 1=little 0=big */ | |
170 | #define HPC3_ETXCTRL_ACTIVE 0x00000200 /* DMA tx channel is active */ | |
171 | #define HPC3_ETXCTRL_AMASK 0x00000400 /* Indicates ACTIVE inhibits PIO's */ | |
172 | ||
173 | volatile u32 tx_gfptr; /* current GIO fifo ptr */ | |
174 | volatile u32 tx_dfptr; /* current device fifo ptr */ | |
175 | u32 _unused4[0x1000/4 - 4]; /* padding */ | |
176 | }; | |
177 | ||
178 | struct hpc3_regs { | |
179 | /* First regs for the PBUS 8 dma channels. */ | |
180 | struct hpc3_pbus_dmacregs pbdma[8]; | |
181 | ||
182 | /* Now the HPC scsi registers, we get two scsi reg sets. */ | |
183 | struct hpc3_scsiregs scsi_chan0, scsi_chan1; | |
184 | ||
185 | /* The SEEQ hpc3 ethernet dma/control registers. */ | |
186 | struct hpc3_ethregs ethregs; | |
187 | ||
188 | /* Here are where the hpc3 fifo's can be directly accessed | |
189 | * via PIO accesses. Under normal operation we never stick | |
190 | * our grubby paws in here so it's just padding. */ | |
191 | u32 _unused0[0x18000/4]; | |
192 | ||
193 | /* HPC3 irq status regs. Due to a peculiar bug you need to | |
194 | * look at two different register addresses to get at all of | |
195 | * the status bits. The first reg can only reliably report | |
196 | * bits 4:0 of the status, and the second reg can only | |
197 | * reliably report bits 9:5 of the hpc3 irq status. I told | |
198 | * you it was a peculiar bug. ;-) | |
199 | */ | |
200 | volatile u32 istat0; /* Irq status, only bits <4:0> reliable. */ | |
201 | #define HPC3_ISTAT_PBIMASK 0x0ff /* irq bits for pbus devs 0 --> 7 */ | |
202 | #define HPC3_ISTAT_SC0MASK 0x100 /* irq bit for scsi channel 0 */ | |
203 | #define HPC3_ISTAT_SC1MASK 0x200 /* irq bit for scsi channel 1 */ | |
204 | ||
205 | volatile u32 gio_misc; /* GIO misc control bits. */ | |
206 | #define HPC3_GIOMISC_ERTIME 0x1 /* Enable external timer real time. */ | |
207 | #define HPC3_GIOMISC_DENDIAN 0x2 /* dma descriptor endian, 1=lit 0=big */ | |
208 | ||
78709b9d | 209 | u32 eeprom; /* EEPROM data reg. */ |
1da177e4 LT |
210 | #define HPC3_EEPROM_EPROT 0x01 /* Protect register enable */ |
211 | #define HPC3_EEPROM_CSEL 0x02 /* Chip select */ | |
212 | #define HPC3_EEPROM_ECLK 0x04 /* EEPROM clock */ | |
213 | #define HPC3_EEPROM_DATO 0x08 /* Data out */ | |
214 | #define HPC3_EEPROM_DATI 0x10 /* Data in */ | |
215 | ||
216 | volatile u32 istat1; /* Irq status, only bits <9:5> reliable. */ | |
217 | volatile u32 bestat; /* Bus error interrupt status reg. */ | |
218 | #define HPC3_BESTAT_BLMASK 0x000ff /* Bus lane where bad parity occurred */ | |
219 | #define HPC3_BESTAT_CTYPE 0x00100 /* Bus cycle type, 0=PIO 1=DMA */ | |
220 | #define HPC3_BESTAT_PIDSHIFT 9 | |
221 | #define HPC3_BESTAT_PIDMASK 0x3f700 /* DMA channel parity identifier */ | |
222 | ||
223 | u32 _unused1[0x14000/4 - 5]; /* padding */ | |
42a3b4f2 | 224 | |
1da177e4 LT |
225 | /* Now direct PIO per-HPC3 peripheral access to external regs. */ |
226 | volatile u32 scsi0_ext[256]; /* SCSI channel 0 external regs */ | |
227 | u32 _unused2[0x7c00/4]; | |
228 | volatile u32 scsi1_ext[256]; /* SCSI channel 1 external regs */ | |
229 | u32 _unused3[0x7c00/4]; | |
230 | volatile u32 eth_ext[320]; /* Ethernet external registers */ | |
231 | u32 _unused4[0x3b00/4]; | |
232 | ||
233 | /* Per-peripheral device external registers and DMA/PIO control. */ | |
234 | volatile u32 pbus_extregs[16][256]; | |
235 | volatile u32 pbus_dmacfg[8][128]; | |
236 | /* Cycles to spend in D3 for reads */ | |
237 | #define HPC3_DMACFG_D3R_MASK 0x00000001 | |
238 | #define HPC3_DMACFG_D3R_SHIFT 0 | |
239 | /* Cycles to spend in D4 for reads */ | |
240 | #define HPC3_DMACFG_D4R_MASK 0x0000001e | |
241 | #define HPC3_DMACFG_D4R_SHIFT 1 | |
242 | /* Cycles to spend in D5 for reads */ | |
243 | #define HPC3_DMACFG_D5R_MASK 0x000001e0 | |
244 | #define HPC3_DMACFG_D5R_SHIFT 5 | |
245 | /* Cycles to spend in D3 for writes */ | |
246 | #define HPC3_DMACFG_D3W_MASK 0x00000200 | |
247 | #define HPC3_DMACFG_D3W_SHIFT 9 | |
248 | /* Cycles to spend in D4 for writes */ | |
249 | #define HPC3_DMACFG_D4W_MASK 0x00003c00 | |
250 | #define HPC3_DMACFG_D4W_SHIFT 10 | |
251 | /* Cycles to spend in D5 for writes */ | |
252 | #define HPC3_DMACFG_D5W_MASK 0x0003c000 | |
253 | #define HPC3_DMACFG_D5W_SHIFT 14 | |
254 | /* Enable 16-bit DMA access mode */ | |
255 | #define HPC3_DMACFG_DS16 0x00040000 | |
256 | /* Places halfwords on high 16 bits of bus */ | |
257 | #define HPC3_DMACFG_EVENHI 0x00080000 | |
258 | /* Make this device real time */ | |
259 | #define HPC3_DMACFG_RTIME 0x00200000 | |
260 | /* 5 bit burst count for DMA device */ | |
261 | #define HPC3_DMACFG_BURST_MASK 0x07c00000 | |
262 | #define HPC3_DMACFG_BURST_SHIFT 22 | |
263 | /* Use live pbus_dreq unsynchronized signal */ | |
264 | #define HPC3_DMACFG_DRQLIVE 0x08000000 | |
265 | volatile u32 pbus_piocfg[16][64]; | |
266 | /* Cycles to spend in P2 state for reads */ | |
267 | #define HPC3_PIOCFG_P2R_MASK 0x00001 | |
268 | #define HPC3_PIOCFG_P2R_SHIFT 0 | |
269 | /* Cycles to spend in P3 state for reads */ | |
270 | #define HPC3_PIOCFG_P3R_MASK 0x0001e | |
271 | #define HPC3_PIOCFG_P3R_SHIFT 1 | |
272 | /* Cycles to spend in P4 state for reads */ | |
273 | #define HPC3_PIOCFG_P4R_MASK 0x001e0 | |
274 | #define HPC3_PIOCFG_P4R_SHIFT 5 | |
275 | /* Cycles to spend in P2 state for writes */ | |
276 | #define HPC3_PIOCFG_P2W_MASK 0x00200 | |
277 | #define HPC3_PIOCFG_P2W_SHIFT 9 | |
278 | /* Cycles to spend in P3 state for writes */ | |
279 | #define HPC3_PIOCFG_P3W_MASK 0x03c00 | |
280 | #define HPC3_PIOCFG_P3W_SHIFT 10 | |
281 | /* Cycles to spend in P4 state for writes */ | |
282 | #define HPC3_PIOCFG_P4W_MASK 0x3c000 | |
283 | #define HPC3_PIOCFG_P4W_SHIFT 14 | |
284 | /* Enable 16-bit PIO accesses */ | |
285 | #define HPC3_PIOCFG_DS16 0x40000 | |
286 | /* Place even address bits in bits <15:8> */ | |
287 | #define HPC3_PIOCFG_EVENHI 0x80000 | |
288 | ||
289 | /* PBUS PROM control regs. */ | |
290 | volatile u32 pbus_promwe; /* PROM write enable register */ | |
291 | #define HPC3_PROM_WENAB 0x1 /* Enable writes to the PROM */ | |
292 | ||
293 | u32 _unused5[0x0800/4 - 1]; | |
294 | volatile u32 pbus_promswap; /* Chip select swap reg */ | |
295 | #define HPC3_PROM_SWAP 0x1 /* invert GIO addr bit to select prom0 or prom1 */ | |
296 | ||
297 | u32 _unused6[0x0800/4 - 1]; | |
298 | volatile u32 pbus_gout; /* PROM general purpose output reg */ | |
299 | #define HPC3_PROM_STAT 0x1 /* General purpose status bit in gout */ | |
300 | ||
301 | u32 _unused7[0x1000/4 - 1]; | |
302 | volatile u32 rtcregs[14]; /* Dallas clock registers */ | |
303 | u32 _unused8[50]; | |
304 | volatile u32 bbram[8192-50-14]; /* Battery backed ram */ | |
305 | }; | |
306 | ||
42a3b4f2 | 307 | /* |
1da177e4 LT |
308 | * It is possible to have two HPC3's within the address space on |
309 | * one machine, though only having one is more likely on an Indy. | |
310 | */ | |
311 | extern struct hpc3_regs *hpc3c0, *hpc3c1; | |
312 | #define HPC3_CHIP0_BASE 0x1fb80000 /* physical */ | |
313 | #define HPC3_CHIP1_BASE 0x1fb00000 /* physical */ | |
314 | ||
315 | extern void sgihpc_init(void); | |
316 | ||
317 | #endif /* _SGI_HPC3_H */ |