projects / mirror_ubuntu-artful-kernel.git / blame
| Commit | Line | Data |
|---|---|---|
| 3f0292ae HS |
1 | /* |
| 2 | * gpio-regulator.h | |
| 3 | * | |
| 4 | * Copyright 2011 Heiko Stuebner <heiko@sntech.de> | |
| 5 | * | |
| 6 | * based on fixed.h | |
| 7 | * | |
| 8 | * Copyright 2008 Wolfson Microelectronics PLC. | |
| 9 | * | |
| 10 | * Author: Mark Brown <broonie@opensource.wolfsonmicro.com> | |
| 11 | * | |
| 12 | * Copyright (c) 2009 Nokia Corporation | |
| 13 | * Roger Quadros <ext-roger.quadros@nokia.com> | |
| 14 | * | |
| 15 | * This program is free software; you can redistribute it and/or | |
| 16 | * modify it under the terms of the GNU General Public License as | |
| 17 | * published by the Free Software Foundation; either version 2 of the | |
| 18 | * License, or (at your option) any later version. | |
| 19 | */ | |
| 20 | ||
| 21 | #ifndef __REGULATOR_GPIO_H | |
| 22 | #define __REGULATOR_GPIO_H | |
| 23 | ||
| 24 | struct regulator_init_data; | |
| 25 | ||
| 26 | enum regulator_type; | |
| 27 | ||
| 28 | /** | |
| 29 | * struct gpio_regulator_state - state description | |
| 30 | * @value: microvolts or microamps | |
| 31 | * @gpios: bitfield of gpio target-states for the value | |
| 32 | * | |
| 33 | * This structure describes a supported setting of the regulator | |
| 34 | * and the necessary gpio-state to achieve it. | |
| 35 | * | |
| 36 | * The n-th bit in the bitfield describes the state of the n-th GPIO | |
| 37 | * from the gpios-array defined in gpio_regulator_config below. | |
| 38 | */ | |
| 39 | struct gpio_regulator_state { | |
| 40 | int value; | |
| 41 | int gpios; | |
| 42 | }; | |
| 43 | ||
| 44 | /** | |
| 45 | * struct gpio_regulator_config - config structure | |
| 46 | * @supply_name: Name of the regulator supply | |
| 47 | * @enable_gpio: GPIO to use for enable control | |
| 48 | * set to -EINVAL if not used | |
| 49 | * @enable_high: Polarity of enable GPIO | |
| 50 | * 1 = Active high, 0 = Active low | |
| 51 | * @enabled_at_boot: Whether regulator has been enabled at | |
| 52 | * boot or not. 1 = Yes, 0 = No | |
| 53 | * This is used to keep the regulator at | |
| 54 | * the default state | |
| 55 | * @startup_delay: Start-up time in microseconds | |
| 56 | * @gpios: Array containing the gpios needed to control | |
| 57 | * the setting of the regulator | |
| 58 | * @nr_gpios: Number of gpios | |
| 59 | * @states: Array of gpio_regulator_state entries describing | |
| 60 | * the gpio state for specific voltages | |
| 61 | * @nr_states: Number of states available | |
| 62 | * @regulator_type: either REGULATOR_CURRENT or REGULATOR_VOLTAGE | |
| 63 | * @init_data: regulator_init_data | |
| 64 | * | |
| 65 | * This structure contains gpio-voltage regulator configuration | |
| 66 | * information that must be passed by platform code to the | |
| 67 | * gpio-voltage regulator driver. | |
| 68 | */ | |
| 69 | struct gpio_regulator_config { | |
| 70 | const char *supply_name; | |
| 71 | ||
| 72 | int enable_gpio; | |
| 73 | unsigned enable_high:1; | |
| 74 | unsigned enabled_at_boot:1; | |
| 75 | unsigned startup_delay; | |
| 76 | ||
| 77 | struct gpio *gpios; | |
| 78 | int nr_gpios; | |
| 79 | ||
| 80 | struct gpio_regulator_state *states; | |
| 81 | int nr_states; | |
| 82 | ||
| 83 | enum regulator_type type; | |
| 84 | struct regulator_init_data *init_data; | |
| 85 | }; | |
| 86 | ||
| 87 | #endif |