projects / mirror_ubuntu-hirsute-kernel.git / blame
| Commit | Line | Data |
|---|---|---|
| 6b293258 BH |
1 | /* SPDX-License-Identifier: GPL-2.0+ WITH Linux-syscall-note */ |
| 2 | #ifndef _UAPI_LINUX_FSI_H | |
| 3 | #define _UAPI_LINUX_FSI_H | |
| 4 | ||
| 5 | #include <linux/types.h> | |
| 6 | #include <linux/ioctl.h> | |
| 7 | ||
| 8 | /* | |
| 9 | * /dev/scom "raw" ioctl interface | |
| 10 | * | |
| 11 | * The driver supports a high level "read/write" interface which | |
| 12 | * handles retries and converts the status to Linux error codes, | |
| 13 | * however low level tools an debugger need to access the "raw" | |
| 14 | * HW status information and interpret it themselves, so this | |
| 15 | * ioctl interface is also provided for their use case. | |
| 16 | */ | |
| 17 | ||
| 18 | /* Structure for SCOM read/write */ | |
| 19 | struct scom_access { | |
| 20 | __u64 addr; /* SCOM address, supports indirect */ | |
| 21 | __u64 data; /* SCOM data (in for write, out for read) */ | |
| 22 | __u64 mask; /* Data mask for writes */ | |
| 23 | __u32 intf_errors; /* Interface error flags */ | |
| 24 | #define SCOM_INTF_ERR_PARITY 0x00000001 /* Parity error */ | |
| 25 | #define SCOM_INTF_ERR_PROTECTION 0x00000002 /* Blocked by secure boot */ | |
| 26 | #define SCOM_INTF_ERR_ABORT 0x00000004 /* PIB reset during access */ | |
| 27 | #define SCOM_INTF_ERR_UNKNOWN 0x80000000 /* Unknown error */ | |
| 28 | /* | |
| 29 | * Note: Any other bit set in intf_errors need to be considered as an | |
| 30 | * error. Future implementations may define new error conditions. The | |
| 31 | * pib_status below is only valid if intf_errors is 0. | |
| 32 | */ | |
| 33 | __u8 pib_status; /* 3-bit PIB status */ | |
| 34 | #define SCOM_PIB_SUCCESS 0 /* Access successful */ | |
| 35 | #define SCOM_PIB_BLOCKED 1 /* PIB blocked, pls retry */ | |
| 36 | #define SCOM_PIB_OFFLINE 2 /* Chiplet offline */ | |
| 37 | #define SCOM_PIB_PARTIAL 3 /* Partial good */ | |
| 38 | #define SCOM_PIB_BAD_ADDR 4 /* Invalid address */ | |
| 39 | #define SCOM_PIB_CLK_ERR 5 /* Clock error */ | |
| 40 | #define SCOM_PIB_PARITY_ERR 6 /* Parity error on the PIB bus */ | |
| 41 | #define SCOM_PIB_TIMEOUT 7 /* Bus timeout */ | |
| 42 | __u8 pad; | |
| 43 | }; | |
| 44 | ||
| 45 | /* Flags for SCOM check */ | |
| 46 | #define SCOM_CHECK_SUPPORTED 0x00000001 /* Interface supported */ | |
| 47 | #define SCOM_CHECK_PROTECTED 0x00000002 /* Interface blocked by secure boot */ | |
| 48 | ||
| 49 | /* Flags for SCOM reset */ | |
| 50 | #define SCOM_RESET_INTF 0x00000001 /* Reset interface */ | |
| 51 | #define SCOM_RESET_PIB 0x00000002 /* Reset PIB */ | |
| 52 | ||
| 53 | #define FSI_SCOM_CHECK _IOR('s', 0x00, __u32) | |
| 54 | #define FSI_SCOM_READ _IOWR('s', 0x01, struct scom_access) | |
| 55 | #define FSI_SCOM_WRITE _IOWR('s', 0x02, struct scom_access) | |
| 56 | #define FSI_SCOM_RESET _IOW('s', 0x03, __u32) | |
| 57 | ||
| 58 | #endif /* _UAPI_LINUX_FSI_H */ |