]>
Commit | Line | Data |
---|---|---|
1 | /* seeq8005.c: A network driver for linux. */ | |
2 | /* | |
3 | Based on skeleton.c, | |
4 | Written 1993-94 by Donald Becker. | |
5 | See the skeleton.c file for further copyright information. | |
6 | ||
7 | This software may be used and distributed according to the terms | |
8 | of the GNU General Public License, incorporated herein by reference. | |
9 | ||
10 | The author may be reached as hamish@zot.apana.org.au | |
11 | ||
12 | This file is a network device driver for the SEEQ 8005 chipset and | |
13 | the Linux operating system. | |
14 | ||
15 | */ | |
16 | ||
17 | static const char version[] = | |
18 | "seeq8005.c:v1.00 8/07/95 Hamish Coleman (hamish@zot.apana.org.au)\n"; | |
19 | ||
20 | /* | |
21 | Sources: | |
22 | SEEQ 8005 databook | |
23 | ||
24 | Version history: | |
25 | 1.00 Public release. cosmetic changes (no warnings now) | |
26 | 0.68 Turning per- packet,interrupt debug messages off - testing for release. | |
27 | 0.67 timing problems/bad buffer reads seem to be fixed now | |
28 | 0.63 *!@$ protocol=eth_type_trans -- now packets flow | |
29 | 0.56 Send working | |
30 | 0.48 Receive working | |
31 | */ | |
32 | ||
33 | #include <linux/module.h> | |
34 | #include <linux/kernel.h> | |
35 | #include <linux/types.h> | |
36 | #include <linux/fcntl.h> | |
37 | #include <linux/interrupt.h> | |
38 | #include <linux/ioport.h> | |
39 | #include <linux/in.h> | |
40 | #include <linux/string.h> | |
41 | #include <linux/init.h> | |
42 | #include <linux/delay.h> | |
43 | #include <linux/errno.h> | |
44 | #include <linux/netdevice.h> | |
45 | #include <linux/etherdevice.h> | |
46 | #include <linux/skbuff.h> | |
47 | #include <linux/bitops.h> | |
48 | #include <linux/jiffies.h> | |
49 | ||
50 | #include <asm/system.h> | |
51 | #include <asm/io.h> | |
52 | #include <asm/dma.h> | |
53 | ||
54 | #include "seeq8005.h" | |
55 | ||
56 | /* First, a few definitions that the brave might change. */ | |
57 | /* A zero-terminated list of I/O addresses to be probed. */ | |
58 | static unsigned int seeq8005_portlist[] __initdata = | |
59 | { 0x300, 0x320, 0x340, 0x360, 0}; | |
60 | ||
61 | /* use 0 for production, 1 for verification, >2 for debug */ | |
62 | #ifndef NET_DEBUG | |
63 | #define NET_DEBUG 1 | |
64 | #endif | |
65 | static unsigned int net_debug = NET_DEBUG; | |
66 | ||
67 | /* Information that need to be kept for each board. */ | |
68 | struct net_local { | |
69 | unsigned short receive_ptr; /* What address in packet memory do we expect a recv_pkt_header? */ | |
70 | long open_time; /* Useless example local info. */ | |
71 | }; | |
72 | ||
73 | /* The station (ethernet) address prefix, used for IDing the board. */ | |
74 | #define SA_ADDR0 0x00 | |
75 | #define SA_ADDR1 0x80 | |
76 | #define SA_ADDR2 0x4b | |
77 | ||
78 | /* Index to functions, as function prototypes. */ | |
79 | ||
80 | static int seeq8005_probe1(struct net_device *dev, int ioaddr); | |
81 | static int seeq8005_open(struct net_device *dev); | |
82 | static void seeq8005_timeout(struct net_device *dev); | |
83 | static netdev_tx_t seeq8005_send_packet(struct sk_buff *skb, | |
84 | struct net_device *dev); | |
85 | static irqreturn_t seeq8005_interrupt(int irq, void *dev_id); | |
86 | static void seeq8005_rx(struct net_device *dev); | |
87 | static int seeq8005_close(struct net_device *dev); | |
88 | static void set_multicast_list(struct net_device *dev); | |
89 | ||
90 | /* Example routines you must write ;->. */ | |
91 | #define tx_done(dev) (inw(SEEQ_STATUS) & SEEQSTAT_TX_ON) | |
92 | static void hardware_send_packet(struct net_device *dev, char *buf, int length); | |
93 | extern void seeq8005_init(struct net_device *dev, int startp); | |
94 | static inline void wait_for_buffer(struct net_device *dev); | |
95 | ||
96 | ||
97 | /* Check for a network adaptor of this type, and return '0' iff one exists. | |
98 | If dev->base_addr == 0, probe all likely locations. | |
99 | If dev->base_addr == 1, always return failure. | |
100 | */ | |
101 | ||
102 | static int io = 0x320; | |
103 | static int irq = 10; | |
104 | ||
105 | struct net_device * __init seeq8005_probe(int unit) | |
106 | { | |
107 | struct net_device *dev = alloc_etherdev(sizeof(struct net_local)); | |
108 | unsigned *port; | |
109 | int err = 0; | |
110 | ||
111 | if (!dev) | |
112 | return ERR_PTR(-ENODEV); | |
113 | ||
114 | if (unit >= 0) { | |
115 | sprintf(dev->name, "eth%d", unit); | |
116 | netdev_boot_setup_check(dev); | |
117 | io = dev->base_addr; | |
118 | irq = dev->irq; | |
119 | } | |
120 | ||
121 | if (io > 0x1ff) { /* Check a single specified location. */ | |
122 | err = seeq8005_probe1(dev, io); | |
123 | } else if (io != 0) { /* Don't probe at all. */ | |
124 | err = -ENXIO; | |
125 | } else { | |
126 | for (port = seeq8005_portlist; *port; port++) { | |
127 | if (seeq8005_probe1(dev, *port) == 0) | |
128 | break; | |
129 | } | |
130 | if (!*port) | |
131 | err = -ENODEV; | |
132 | } | |
133 | if (err) | |
134 | goto out; | |
135 | err = register_netdev(dev); | |
136 | if (err) | |
137 | goto out1; | |
138 | return dev; | |
139 | out1: | |
140 | release_region(dev->base_addr, SEEQ8005_IO_EXTENT); | |
141 | out: | |
142 | free_netdev(dev); | |
143 | return ERR_PTR(err); | |
144 | } | |
145 | ||
146 | static const struct net_device_ops seeq8005_netdev_ops = { | |
147 | .ndo_open = seeq8005_open, | |
148 | .ndo_stop = seeq8005_close, | |
149 | .ndo_start_xmit = seeq8005_send_packet, | |
150 | .ndo_tx_timeout = seeq8005_timeout, | |
151 | .ndo_set_multicast_list = set_multicast_list, | |
152 | .ndo_change_mtu = eth_change_mtu, | |
153 | .ndo_set_mac_address = eth_mac_addr, | |
154 | .ndo_validate_addr = eth_validate_addr, | |
155 | }; | |
156 | ||
157 | /* This is the real probe routine. Linux has a history of friendly device | |
158 | probes on the ISA bus. A good device probes avoids doing writes, and | |
159 | verifies that the correct device exists and functions. */ | |
160 | ||
161 | static int __init seeq8005_probe1(struct net_device *dev, int ioaddr) | |
162 | { | |
163 | static unsigned version_printed; | |
164 | int i,j; | |
165 | unsigned char SA_prom[32]; | |
166 | int old_cfg1; | |
167 | int old_cfg2; | |
168 | int old_stat; | |
169 | int old_dmaar; | |
170 | int old_rear; | |
171 | int retval; | |
172 | ||
173 | if (!request_region(ioaddr, SEEQ8005_IO_EXTENT, "seeq8005")) | |
174 | return -ENODEV; | |
175 | ||
176 | if (net_debug>1) | |
177 | printk("seeq8005: probing at 0x%x\n",ioaddr); | |
178 | ||
179 | old_stat = inw(SEEQ_STATUS); /* read status register */ | |
180 | if (old_stat == 0xffff) { | |
181 | retval = -ENODEV; | |
182 | goto out; /* assume that 0xffff == no device */ | |
183 | } | |
184 | if ( (old_stat & 0x1800) != 0x1800 ) { /* assume that unused bits are 1, as my manual says */ | |
185 | if (net_debug>1) { | |
186 | printk("seeq8005: reserved stat bits != 0x1800\n"); | |
187 | printk(" == 0x%04x\n",old_stat); | |
188 | } | |
189 | retval = -ENODEV; | |
190 | goto out; | |
191 | } | |
192 | ||
193 | old_rear = inw(SEEQ_REA); | |
194 | if (old_rear == 0xffff) { | |
195 | outw(0,SEEQ_REA); | |
196 | if (inw(SEEQ_REA) == 0xffff) { /* assume that 0xffff == no device */ | |
197 | retval = -ENODEV; | |
198 | goto out; | |
199 | } | |
200 | } else if ((old_rear & 0xff00) != 0xff00) { /* assume that unused bits are 1 */ | |
201 | if (net_debug>1) { | |
202 | printk("seeq8005: unused rear bits != 0xff00\n"); | |
203 | printk(" == 0x%04x\n",old_rear); | |
204 | } | |
205 | retval = -ENODEV; | |
206 | goto out; | |
207 | } | |
208 | ||
209 | old_cfg2 = inw(SEEQ_CFG2); /* read CFG2 register */ | |
210 | old_cfg1 = inw(SEEQ_CFG1); | |
211 | old_dmaar = inw(SEEQ_DMAAR); | |
212 | ||
213 | if (net_debug>4) { | |
214 | printk("seeq8005: stat = 0x%04x\n",old_stat); | |
215 | printk("seeq8005: cfg1 = 0x%04x\n",old_cfg1); | |
216 | printk("seeq8005: cfg2 = 0x%04x\n",old_cfg2); | |
217 | printk("seeq8005: raer = 0x%04x\n",old_rear); | |
218 | printk("seeq8005: dmaar= 0x%04x\n",old_dmaar); | |
219 | } | |
220 | ||
221 | outw( SEEQCMD_FIFO_WRITE | SEEQCMD_SET_ALL_OFF, SEEQ_CMD); /* setup for reading PROM */ | |
222 | outw( 0, SEEQ_DMAAR); /* set starting PROM address */ | |
223 | outw( SEEQCFG1_BUFFER_PROM, SEEQ_CFG1); /* set buffer to look at PROM */ | |
224 | ||
225 | ||
226 | j=0; | |
227 | for(i=0; i <32; i++) { | |
228 | j+= SA_prom[i] = inw(SEEQ_BUFFER) & 0xff; | |
229 | } | |
230 | ||
231 | #if 0 | |
232 | /* untested because I only have the one card */ | |
233 | if ( (j&0xff) != 0 ) { /* checksum appears to be 8bit = 0 */ | |
234 | if (net_debug>1) { /* check this before deciding that we have a card */ | |
235 | printk("seeq8005: prom sum error\n"); | |
236 | } | |
237 | outw( old_stat, SEEQ_STATUS); | |
238 | outw( old_dmaar, SEEQ_DMAAR); | |
239 | outw( old_cfg1, SEEQ_CFG1); | |
240 | retval = -ENODEV; | |
241 | goto out; | |
242 | } | |
243 | #endif | |
244 | ||
245 | outw( SEEQCFG2_RESET, SEEQ_CFG2); /* reset the card */ | |
246 | udelay(5); | |
247 | outw( SEEQCMD_SET_ALL_OFF, SEEQ_CMD); | |
248 | ||
249 | if (net_debug) { | |
250 | printk("seeq8005: prom sum = 0x%08x\n",j); | |
251 | for(j=0; j<32; j+=16) { | |
252 | printk("seeq8005: prom %02x: ",j); | |
253 | for(i=0;i<16;i++) { | |
254 | printk("%02x ",SA_prom[j|i]); | |
255 | } | |
256 | printk(" "); | |
257 | for(i=0;i<16;i++) { | |
258 | if ((SA_prom[j|i]>31)&&(SA_prom[j|i]<127)) { | |
259 | printk("%c", SA_prom[j|i]); | |
260 | } else { | |
261 | printk(" "); | |
262 | } | |
263 | } | |
264 | printk("\n"); | |
265 | } | |
266 | } | |
267 | ||
268 | #if 0 | |
269 | /* | |
270 | * testing the packet buffer memory doesn't work yet | |
271 | * but all other buffer accesses do | |
272 | * - fixing is not a priority | |
273 | */ | |
274 | if (net_debug>1) { /* test packet buffer memory */ | |
275 | printk("seeq8005: testing packet buffer ... "); | |
276 | outw( SEEQCFG1_BUFFER_BUFFER, SEEQ_CFG1); | |
277 | outw( SEEQCMD_FIFO_WRITE | SEEQCMD_SET_ALL_OFF, SEEQ_CMD); | |
278 | outw( 0 , SEEQ_DMAAR); | |
279 | for(i=0;i<32768;i++) { | |
280 | outw(0x5a5a, SEEQ_BUFFER); | |
281 | } | |
282 | j=jiffies+HZ; | |
283 | while ( ((inw(SEEQ_STATUS) & SEEQSTAT_FIFO_EMPTY) != SEEQSTAT_FIFO_EMPTY) && time_before(jiffies, j) ) | |
284 | mb(); | |
285 | outw( 0 , SEEQ_DMAAR); | |
286 | while ( ((inw(SEEQ_STATUS) & SEEQSTAT_WINDOW_INT) != SEEQSTAT_WINDOW_INT) && time_before(jiffies, j+HZ)) | |
287 | mb(); | |
288 | if ( (inw(SEEQ_STATUS) & SEEQSTAT_WINDOW_INT) == SEEQSTAT_WINDOW_INT) | |
289 | outw( SEEQCMD_WINDOW_INT_ACK | (inw(SEEQ_STATUS)& SEEQCMD_INT_MASK), SEEQ_CMD); | |
290 | outw( SEEQCMD_FIFO_READ | SEEQCMD_SET_ALL_OFF, SEEQ_CMD); | |
291 | j=0; | |
292 | for(i=0;i<32768;i++) { | |
293 | if (inw(SEEQ_BUFFER) != 0x5a5a) | |
294 | j++; | |
295 | } | |
296 | if (j) { | |
297 | printk("%i\n",j); | |
298 | } else { | |
299 | printk("ok.\n"); | |
300 | } | |
301 | } | |
302 | #endif | |
303 | ||
304 | if (net_debug && version_printed++ == 0) | |
305 | printk(version); | |
306 | ||
307 | printk("%s: %s found at %#3x, ", dev->name, "seeq8005", ioaddr); | |
308 | ||
309 | /* Fill in the 'dev' fields. */ | |
310 | dev->base_addr = ioaddr; | |
311 | dev->irq = irq; | |
312 | ||
313 | /* Retrieve and print the ethernet address. */ | |
314 | for (i = 0; i < 6; i++) | |
315 | dev->dev_addr[i] = SA_prom[i+6]; | |
316 | printk("%pM", dev->dev_addr); | |
317 | ||
318 | if (dev->irq == 0xff) | |
319 | ; /* Do nothing: a user-level program will set it. */ | |
320 | else if (dev->irq < 2) { /* "Auto-IRQ" */ | |
321 | unsigned long cookie = probe_irq_on(); | |
322 | ||
323 | outw( SEEQCMD_RX_INT_EN | SEEQCMD_SET_RX_ON | SEEQCMD_SET_RX_OFF, SEEQ_CMD ); | |
324 | ||
325 | dev->irq = probe_irq_off(cookie); | |
326 | ||
327 | if (net_debug >= 2) | |
328 | printk(" autoirq is %d\n", dev->irq); | |
329 | } else if (dev->irq == 2) | |
330 | /* Fixup for users that don't know that IRQ 2 is really IRQ 9, | |
331 | * or don't know which one to set. | |
332 | */ | |
333 | dev->irq = 9; | |
334 | ||
335 | #if 0 | |
336 | { | |
337 | int irqval = request_irq(dev->irq, seeq8005_interrupt, 0, "seeq8005", dev); | |
338 | if (irqval) { | |
339 | printk ("%s: unable to get IRQ %d (irqval=%d).\n", dev->name, | |
340 | dev->irq, irqval); | |
341 | retval = -EAGAIN; | |
342 | goto out; | |
343 | } | |
344 | } | |
345 | #endif | |
346 | dev->netdev_ops = &seeq8005_netdev_ops; | |
347 | dev->watchdog_timeo = HZ/20; | |
348 | dev->flags &= ~IFF_MULTICAST; | |
349 | ||
350 | return 0; | |
351 | out: | |
352 | release_region(ioaddr, SEEQ8005_IO_EXTENT); | |
353 | return retval; | |
354 | } | |
355 | ||
356 | ||
357 | /* Open/initialize the board. This is called (in the current kernel) | |
358 | sometime after booting when the 'ifconfig' program is run. | |
359 | ||
360 | This routine should set everything up anew at each open, even | |
361 | registers that "should" only need to be set once at boot, so that | |
362 | there is non-reboot way to recover if something goes wrong. | |
363 | */ | |
364 | static int seeq8005_open(struct net_device *dev) | |
365 | { | |
366 | struct net_local *lp = netdev_priv(dev); | |
367 | ||
368 | { | |
369 | int irqval = request_irq(dev->irq, seeq8005_interrupt, 0, "seeq8005", dev); | |
370 | if (irqval) { | |
371 | printk ("%s: unable to get IRQ %d (irqval=%d).\n", dev->name, | |
372 | dev->irq, irqval); | |
373 | return -EAGAIN; | |
374 | } | |
375 | } | |
376 | ||
377 | /* Reset the hardware here. Don't forget to set the station address. */ | |
378 | seeq8005_init(dev, 1); | |
379 | ||
380 | lp->open_time = jiffies; | |
381 | ||
382 | netif_start_queue(dev); | |
383 | return 0; | |
384 | } | |
385 | ||
386 | static void seeq8005_timeout(struct net_device *dev) | |
387 | { | |
388 | int ioaddr = dev->base_addr; | |
389 | printk(KERN_WARNING "%s: transmit timed out, %s?\n", dev->name, | |
390 | tx_done(dev) ? "IRQ conflict" : "network cable problem"); | |
391 | /* Try to restart the adaptor. */ | |
392 | seeq8005_init(dev, 1); | |
393 | dev->trans_start = jiffies; /* prevent tx timeout */ | |
394 | netif_wake_queue(dev); | |
395 | } | |
396 | ||
397 | static netdev_tx_t seeq8005_send_packet(struct sk_buff *skb, | |
398 | struct net_device *dev) | |
399 | { | |
400 | short length = skb->len; | |
401 | unsigned char *buf; | |
402 | ||
403 | if (length < ETH_ZLEN) { | |
404 | if (skb_padto(skb, ETH_ZLEN)) | |
405 | return NETDEV_TX_OK; | |
406 | length = ETH_ZLEN; | |
407 | } | |
408 | buf = skb->data; | |
409 | ||
410 | /* Block a timer-based transmit from overlapping */ | |
411 | netif_stop_queue(dev); | |
412 | ||
413 | hardware_send_packet(dev, buf, length); | |
414 | dev->stats.tx_bytes += length; | |
415 | dev_kfree_skb (skb); | |
416 | /* You might need to clean up and record Tx statistics here. */ | |
417 | ||
418 | return NETDEV_TX_OK; | |
419 | } | |
420 | ||
421 | /* | |
422 | * wait_for_buffer | |
423 | * | |
424 | * This routine waits for the SEEQ chip to assert that the FIFO is ready | |
425 | * by checking for a window interrupt, and then clearing it. This has to | |
426 | * occur in the interrupt handler! | |
427 | */ | |
428 | inline void wait_for_buffer(struct net_device * dev) | |
429 | { | |
430 | int ioaddr = dev->base_addr; | |
431 | unsigned long tmp; | |
432 | int status; | |
433 | ||
434 | tmp = jiffies + HZ; | |
435 | while ( ( ((status=inw(SEEQ_STATUS)) & SEEQSTAT_WINDOW_INT) != SEEQSTAT_WINDOW_INT) && time_before(jiffies, tmp)) | |
436 | cpu_relax(); | |
437 | ||
438 | if ( (status & SEEQSTAT_WINDOW_INT) == SEEQSTAT_WINDOW_INT) | |
439 | outw( SEEQCMD_WINDOW_INT_ACK | (status & SEEQCMD_INT_MASK), SEEQ_CMD); | |
440 | } | |
441 | ||
442 | /* The typical workload of the driver: | |
443 | Handle the network interface interrupts. */ | |
444 | static irqreturn_t seeq8005_interrupt(int irq, void *dev_id) | |
445 | { | |
446 | struct net_device *dev = dev_id; | |
447 | struct net_local *lp; | |
448 | int ioaddr, status, boguscount = 0; | |
449 | int handled = 0; | |
450 | ||
451 | ioaddr = dev->base_addr; | |
452 | lp = netdev_priv(dev); | |
453 | ||
454 | status = inw(SEEQ_STATUS); | |
455 | do { | |
456 | if (net_debug >2) { | |
457 | printk("%s: int, status=0x%04x\n",dev->name,status); | |
458 | } | |
459 | ||
460 | if (status & SEEQSTAT_WINDOW_INT) { | |
461 | handled = 1; | |
462 | outw( SEEQCMD_WINDOW_INT_ACK | (status & SEEQCMD_INT_MASK), SEEQ_CMD); | |
463 | if (net_debug) { | |
464 | printk("%s: window int!\n",dev->name); | |
465 | } | |
466 | } | |
467 | if (status & SEEQSTAT_TX_INT) { | |
468 | handled = 1; | |
469 | outw( SEEQCMD_TX_INT_ACK | (status & SEEQCMD_INT_MASK), SEEQ_CMD); | |
470 | dev->stats.tx_packets++; | |
471 | netif_wake_queue(dev); /* Inform upper layers. */ | |
472 | } | |
473 | if (status & SEEQSTAT_RX_INT) { | |
474 | handled = 1; | |
475 | /* Got a packet(s). */ | |
476 | seeq8005_rx(dev); | |
477 | } | |
478 | status = inw(SEEQ_STATUS); | |
479 | } while ( (++boguscount < 10) && (status & SEEQSTAT_ANY_INT)) ; | |
480 | ||
481 | if(net_debug>2) { | |
482 | printk("%s: eoi\n",dev->name); | |
483 | } | |
484 | return IRQ_RETVAL(handled); | |
485 | } | |
486 | ||
487 | /* We have a good packet(s), get it/them out of the buffers. */ | |
488 | static void seeq8005_rx(struct net_device *dev) | |
489 | { | |
490 | struct net_local *lp = netdev_priv(dev); | |
491 | int boguscount = 10; | |
492 | int pkt_hdr; | |
493 | int ioaddr = dev->base_addr; | |
494 | ||
495 | do { | |
496 | int next_packet; | |
497 | int pkt_len; | |
498 | int i; | |
499 | int status; | |
500 | ||
501 | status = inw(SEEQ_STATUS); | |
502 | outw( lp->receive_ptr, SEEQ_DMAAR); | |
503 | outw(SEEQCMD_FIFO_READ | SEEQCMD_RX_INT_ACK | (status & SEEQCMD_INT_MASK), SEEQ_CMD); | |
504 | wait_for_buffer(dev); | |
505 | next_packet = ntohs(inw(SEEQ_BUFFER)); | |
506 | pkt_hdr = inw(SEEQ_BUFFER); | |
507 | ||
508 | if (net_debug>2) { | |
509 | printk("%s: 0x%04x recv next=0x%04x, hdr=0x%04x\n",dev->name,lp->receive_ptr,next_packet,pkt_hdr); | |
510 | } | |
511 | ||
512 | if ((next_packet == 0) || ((pkt_hdr & SEEQPKTH_CHAIN)==0)) { /* Read all the frames? */ | |
513 | return; /* Done for now */ | |
514 | } | |
515 | ||
516 | if ((pkt_hdr & SEEQPKTS_DONE)==0) | |
517 | break; | |
518 | ||
519 | if (next_packet < lp->receive_ptr) { | |
520 | pkt_len = (next_packet + 0x10000 - ((DEFAULT_TEA+1)<<8)) - lp->receive_ptr - 4; | |
521 | } else { | |
522 | pkt_len = next_packet - lp->receive_ptr - 4; | |
523 | } | |
524 | ||
525 | if (next_packet < ((DEFAULT_TEA+1)<<8)) { /* is the next_packet address sane? */ | |
526 | printk("%s: recv packet ring corrupt, resetting board\n",dev->name); | |
527 | seeq8005_init(dev,1); | |
528 | return; | |
529 | } | |
530 | ||
531 | lp->receive_ptr = next_packet; | |
532 | ||
533 | if (net_debug>2) { | |
534 | printk("%s: recv len=0x%04x\n",dev->name,pkt_len); | |
535 | } | |
536 | ||
537 | if (pkt_hdr & SEEQPKTS_ANY_ERROR) { /* There was an error. */ | |
538 | dev->stats.rx_errors++; | |
539 | if (pkt_hdr & SEEQPKTS_SHORT) dev->stats.rx_frame_errors++; | |
540 | if (pkt_hdr & SEEQPKTS_DRIB) dev->stats.rx_frame_errors++; | |
541 | if (pkt_hdr & SEEQPKTS_OVERSIZE) dev->stats.rx_over_errors++; | |
542 | if (pkt_hdr & SEEQPKTS_CRC_ERR) dev->stats.rx_crc_errors++; | |
543 | /* skip over this packet */ | |
544 | outw( SEEQCMD_FIFO_WRITE | SEEQCMD_DMA_INT_ACK | (status & SEEQCMD_INT_MASK), SEEQ_CMD); | |
545 | outw( (lp->receive_ptr & 0xff00)>>8, SEEQ_REA); | |
546 | } else { | |
547 | /* Malloc up new buffer. */ | |
548 | struct sk_buff *skb; | |
549 | unsigned char *buf; | |
550 | ||
551 | skb = dev_alloc_skb(pkt_len); | |
552 | if (skb == NULL) { | |
553 | printk("%s: Memory squeeze, dropping packet.\n", dev->name); | |
554 | dev->stats.rx_dropped++; | |
555 | break; | |
556 | } | |
557 | skb_reserve(skb, 2); /* align data on 16 byte */ | |
558 | buf = skb_put(skb,pkt_len); | |
559 | ||
560 | insw(SEEQ_BUFFER, buf, (pkt_len + 1) >> 1); | |
561 | ||
562 | if (net_debug>2) { | |
563 | char * p = buf; | |
564 | printk("%s: recv ",dev->name); | |
565 | for(i=0;i<14;i++) { | |
566 | printk("%02x ",*(p++)&0xff); | |
567 | } | |
568 | printk("\n"); | |
569 | } | |
570 | ||
571 | skb->protocol=eth_type_trans(skb,dev); | |
572 | netif_rx(skb); | |
573 | dev->stats.rx_packets++; | |
574 | dev->stats.rx_bytes += pkt_len; | |
575 | } | |
576 | } while ((--boguscount) && (pkt_hdr & SEEQPKTH_CHAIN)); | |
577 | ||
578 | /* If any worth-while packets have been received, netif_rx() | |
579 | has done a mark_bh(NET_BH) for us and will work on them | |
580 | when we get to the bottom-half routine. */ | |
581 | } | |
582 | ||
583 | /* The inverse routine to net_open(). */ | |
584 | static int seeq8005_close(struct net_device *dev) | |
585 | { | |
586 | struct net_local *lp = netdev_priv(dev); | |
587 | int ioaddr = dev->base_addr; | |
588 | ||
589 | lp->open_time = 0; | |
590 | ||
591 | netif_stop_queue(dev); | |
592 | ||
593 | /* Flush the Tx and disable Rx here. */ | |
594 | outw( SEEQCMD_SET_ALL_OFF, SEEQ_CMD); | |
595 | ||
596 | free_irq(dev->irq, dev); | |
597 | ||
598 | /* Update the statistics here. */ | |
599 | ||
600 | return 0; | |
601 | ||
602 | } | |
603 | ||
604 | /* Set or clear the multicast filter for this adaptor. | |
605 | num_addrs == -1 Promiscuous mode, receive all packets | |
606 | num_addrs == 0 Normal mode, clear multicast list | |
607 | num_addrs > 0 Multicast mode, receive normal and MC packets, and do | |
608 | best-effort filtering. | |
609 | */ | |
610 | static void set_multicast_list(struct net_device *dev) | |
611 | { | |
612 | /* | |
613 | * I _could_ do up to 6 addresses here, but won't (yet?) | |
614 | */ | |
615 | ||
616 | #if 0 | |
617 | int ioaddr = dev->base_addr; | |
618 | /* | |
619 | * hmm, not even sure if my matching works _anyway_ - seem to be receiving | |
620 | * _everything_ . . . | |
621 | */ | |
622 | ||
623 | if (num_addrs) { /* Enable promiscuous mode */ | |
624 | outw( (inw(SEEQ_CFG1) & ~SEEQCFG1_MATCH_MASK)| SEEQCFG1_MATCH_ALL, SEEQ_CFG1); | |
625 | dev->flags|=IFF_PROMISC; | |
626 | } else { /* Disable promiscuous mode, use normal mode */ | |
627 | outw( (inw(SEEQ_CFG1) & ~SEEQCFG1_MATCH_MASK)| SEEQCFG1_MATCH_BROAD, SEEQ_CFG1); | |
628 | } | |
629 | #endif | |
630 | } | |
631 | ||
632 | void seeq8005_init(struct net_device *dev, int startp) | |
633 | { | |
634 | struct net_local *lp = netdev_priv(dev); | |
635 | int ioaddr = dev->base_addr; | |
636 | int i; | |
637 | ||
638 | outw(SEEQCFG2_RESET, SEEQ_CFG2); /* reset device */ | |
639 | udelay(5); | |
640 | ||
641 | outw( SEEQCMD_FIFO_WRITE | SEEQCMD_SET_ALL_OFF, SEEQ_CMD); | |
642 | outw( 0, SEEQ_DMAAR); /* load start address into both low and high byte */ | |
643 | /* wait_for_buffer(dev); */ /* I think that you only need a wait for memory buffer */ | |
644 | outw( SEEQCFG1_BUFFER_MAC0, SEEQ_CFG1); | |
645 | ||
646 | for(i=0;i<6;i++) { /* set Station address */ | |
647 | outb(dev->dev_addr[i], SEEQ_BUFFER); | |
648 | udelay(2); | |
649 | } | |
650 | ||
651 | outw( SEEQCFG1_BUFFER_TEA, SEEQ_CFG1); /* set xmit end area pointer to 16K */ | |
652 | outb( DEFAULT_TEA, SEEQ_BUFFER); /* this gives us 16K of send buffer and 48K of recv buffer */ | |
653 | ||
654 | lp->receive_ptr = (DEFAULT_TEA+1)<<8; /* so we can find our packet_header */ | |
655 | outw( lp->receive_ptr, SEEQ_RPR); /* Receive Pointer Register is set to recv buffer memory */ | |
656 | ||
657 | outw( 0x00ff, SEEQ_REA); /* Receive Area End */ | |
658 | ||
659 | if (net_debug>4) { | |
660 | printk("%s: SA0 = ",dev->name); | |
661 | ||
662 | outw( SEEQCMD_FIFO_READ | SEEQCMD_SET_ALL_OFF, SEEQ_CMD); | |
663 | outw( 0, SEEQ_DMAAR); | |
664 | outw( SEEQCFG1_BUFFER_MAC0, SEEQ_CFG1); | |
665 | ||
666 | for(i=0;i<6;i++) { | |
667 | printk("%02x ",inb(SEEQ_BUFFER)); | |
668 | } | |
669 | printk("\n"); | |
670 | } | |
671 | ||
672 | outw( SEEQCFG1_MAC0_EN | SEEQCFG1_MATCH_BROAD | SEEQCFG1_BUFFER_BUFFER, SEEQ_CFG1); | |
673 | outw( SEEQCFG2_AUTO_REA | SEEQCFG2_CTRLO, SEEQ_CFG2); | |
674 | outw( SEEQCMD_SET_RX_ON | SEEQCMD_TX_INT_EN | SEEQCMD_RX_INT_EN, SEEQ_CMD); | |
675 | ||
676 | if (net_debug>4) { | |
677 | int old_cfg1; | |
678 | old_cfg1 = inw(SEEQ_CFG1); | |
679 | printk("%s: stat = 0x%04x\n",dev->name,inw(SEEQ_STATUS)); | |
680 | printk("%s: cfg1 = 0x%04x\n",dev->name,old_cfg1); | |
681 | printk("%s: cfg2 = 0x%04x\n",dev->name,inw(SEEQ_CFG2)); | |
682 | printk("%s: raer = 0x%04x\n",dev->name,inw(SEEQ_REA)); | |
683 | printk("%s: dmaar= 0x%04x\n",dev->name,inw(SEEQ_DMAAR)); | |
684 | ||
685 | } | |
686 | } | |
687 | ||
688 | ||
689 | static void hardware_send_packet(struct net_device * dev, char *buf, int length) | |
690 | { | |
691 | int ioaddr = dev->base_addr; | |
692 | int status = inw(SEEQ_STATUS); | |
693 | int transmit_ptr = 0; | |
694 | unsigned long tmp; | |
695 | ||
696 | if (net_debug>4) { | |
697 | printk("%s: send 0x%04x\n",dev->name,length); | |
698 | } | |
699 | ||
700 | /* Set FIFO to writemode and set packet-buffer address */ | |
701 | outw( SEEQCMD_FIFO_WRITE | (status & SEEQCMD_INT_MASK), SEEQ_CMD); | |
702 | outw( transmit_ptr, SEEQ_DMAAR); | |
703 | ||
704 | /* output SEEQ Packet header barfage */ | |
705 | outw( htons(length + 4), SEEQ_BUFFER); | |
706 | outw( SEEQPKTH_XMIT | SEEQPKTH_DATA_FOLLOWS | SEEQPKTH_XMIT_INT_EN, SEEQ_BUFFER ); | |
707 | ||
708 | /* blat the buffer */ | |
709 | outsw( SEEQ_BUFFER, buf, (length +1) >> 1); | |
710 | /* paranoia !! */ | |
711 | outw( 0, SEEQ_BUFFER); | |
712 | outw( 0, SEEQ_BUFFER); | |
713 | ||
714 | /* set address of start of transmit chain */ | |
715 | outw( transmit_ptr, SEEQ_TPR); | |
716 | ||
717 | /* drain FIFO */ | |
718 | tmp = jiffies; | |
719 | while ( (((status=inw(SEEQ_STATUS)) & SEEQSTAT_FIFO_EMPTY) == 0) && time_before(jiffies, tmp + HZ)) | |
720 | mb(); | |
721 | ||
722 | /* doit ! */ | |
723 | outw( SEEQCMD_WINDOW_INT_ACK | SEEQCMD_SET_TX_ON | (status & SEEQCMD_INT_MASK), SEEQ_CMD); | |
724 | ||
725 | } | |
726 | ||
727 | ||
728 | #ifdef MODULE | |
729 | ||
730 | static struct net_device *dev_seeq; | |
731 | MODULE_LICENSE("GPL"); | |
732 | module_param(io, int, 0); | |
733 | module_param(irq, int, 0); | |
734 | MODULE_PARM_DESC(io, "SEEQ 8005 I/O base address"); | |
735 | MODULE_PARM_DESC(irq, "SEEQ 8005 IRQ number"); | |
736 | ||
737 | int __init init_module(void) | |
738 | { | |
739 | dev_seeq = seeq8005_probe(-1); | |
740 | if (IS_ERR(dev_seeq)) | |
741 | return PTR_ERR(dev_seeq); | |
742 | return 0; | |
743 | } | |
744 | ||
745 | void __exit cleanup_module(void) | |
746 | { | |
747 | unregister_netdev(dev_seeq); | |
748 | release_region(dev_seeq->base_addr, SEEQ8005_IO_EXTENT); | |
749 | free_netdev(dev_seeq); | |
750 | } | |
751 | ||
752 | #endif /* MODULE */ |