Documentation/devicetree/bindings/mfd/qcom-rpm.txt

   1 Qualcomm Resource Power Manager (RPM)
   2
   3 This driver is used to interface with the Resource Power Manager (RPM) found in
   4 various Qualcomm platforms. The RPM allows each component in the system to vote
   5 for state of the system resources, such as clocks, regulators and bus
   6 frequencies.
   7
   8 - compatible:
   9         Usage: required
  10         Value type: <string>
  11         Definition: must be one of:
  12                     "qcom,rpm-apq8064"
  13                     "qcom,rpm-msm8660"
  14                     "qcom,rpm-msm8960"
  15                     "qcom,rpm-ipq8064"
  16                     "qcom,rpm-mdm9615"
  17
  18 - reg:
  19         Usage: required
  20         Value type: <prop-encoded-array>
  21         Definition: base address and size of the RPM's message ram
  22
  23 - interrupts:
  24         Usage: required
  25         Value type: <prop-encoded-array>
  26         Definition: three entries specifying the RPM's:
  27                     1. acknowledgement interrupt
  28                     2. error interrupt
  29                     3. wakeup interrupt
  30
  31 - interrupt-names:
  32         Usage: required
  33         Value type: <string-array>
  34         Definition: must be the three strings "ack", "err" and "wakeup", in order
  35
  36 - qcom,ipc:
  37         Usage: required
  38         Value type: <prop-encoded-array>
  39
  40         Definition: three entries specifying the outgoing ipc bit used for
  41                     signaling the RPM:
  42                     - phandle to a syscon node representing the apcs registers
  43                     - u32 representing offset to the register within the syscon
  44                     - u32 representing the ipc bit within the register
  45
  46
  47 = SUBNODES
  48
  49 The RPM exposes resources to its subnodes. The below bindings specify the set
  50 of valid subnodes that can operate on these resources.
  51
  52 == Regulators
  53
  54 Regulator nodes are identified by their compatible:
  55
  56 - compatible:
  57         Usage: required
  58         Value type: <string>
  59         Definition: must be one of:
  60                     "qcom,rpm-pm8058-regulators"
  61                     "qcom,rpm-pm8901-regulators"
  62                     "qcom,rpm-pm8921-regulators"
  63                     "qcom,rpm-pm8018-regulators"
  64                     "qcom,rpm-smb208-regulators"
  65
  66 - vdd_l0_l1_lvs-supply:
  67 - vdd_l2_l11_l12-supply:
  68 - vdd_l3_l4_l5-supply:
  69 - vdd_l6_l7-supply:
  70 - vdd_l8-supply:
  71 - vdd_l9-supply:
  72 - vdd_l10-supply:
  73 - vdd_l13_l16-supply:
  74 - vdd_l14_l15-supply:
  75 - vdd_l17_l18-supply:
  76 - vdd_l19_l20-supply:
  77 - vdd_l21-supply:
  78 - vdd_l22-supply:
  79 - vdd_l23_l24_l25-supply:
  80 - vdd_ncp-supply:
  81 - vdd_s0-supply:
  82 - vdd_s1-supply:
  83 - vdd_s2-supply:
  84 - vdd_s3-supply:
  85 - vdd_s4-supply:
  86         Usage: optional (pm8058 only)
  87         Value type: <phandle>
  88         Definition: reference to regulator supplying the input pin, as
  89                     described in the data sheet
  90
  91 - lvs0_in-supply:
  92 - lvs1_in-supply:
  93 - lvs2_in-supply:
  94 - lvs3_in-supply:
  95 - mvs_in-supply:
  96 - vdd_l0-supply:
  97 - vdd_l1-supply:
  98 - vdd_l2-supply:
  99 - vdd_l3-supply:
 100 - vdd_l4-supply:
 101 - vdd_l5-supply:
 102 - vdd_l6-supply:
 103 - vdd_s0-supply:
 104 - vdd_s1-supply:
 105 - vdd_s2-supply:
 106 - vdd_s3-supply:
 107 - vdd_s4-supply:
 108         Usage: optional (pm8901 only)
 109         Value type: <phandle>
 110         Definition: reference to regulator supplying the input pin, as
 111                     described in the data sheet
 112
 113 - vdd_l1_l2_l12_l18-supply:
 114 - vdd_l3_l15_l17-supply:
 115 - vdd_l4_l14-supply:
 116 - vdd_l5_l8_l16-supply:
 117 - vdd_l6_l7-supply:
 118 - vdd_l9_l11-supply:
 119 - vdd_l10_l22-supply:
 120 - vdd_l21_l23_l29-supply:
 121 - vdd_l24-supply:
 122 - vdd_l25-supply:
 123 - vdd_l26-supply:
 124 - vdd_l27-supply:
 125 - vdd_l28-supply:
 126 - vdd_ncp-supply:
 127 - vdd_s1-supply:
 128 - vdd_s2-supply:
 129 - vdd_s4-supply:
 130 - vdd_s5-supply:
 131 - vdd_s6-supply:
 132 - vdd_s7-supply:
 133 - vdd_s8-supply:
 134 - vin_5vs-supply:
 135 - vin_lvs1_3_6-supply:
 136 - vin_lvs2-supply:
 137 - vin_lvs4_5_7-supply:
 138         Usage: optional (pm8921 only)
 139         Value type: <phandle>
 140         Definition: reference to regulator supplying the input pin, as
 141                     described in the data sheet
 142
 143 - vin_lvs1-supply:
 144 - vdd_l7-supply:
 145 - vdd_l8-supply:
 146 - vdd_l9_l10_l11_l12-supply:
 147         Usage: optional (pm8018 only)
 148         Value type: <phandle>
 149         Definition: reference to regulator supplying the input pin, as
 150                     described in the data sheet
 151
 152 The regulator node houses sub-nodes for each regulator within the device. Each
 153 sub-node is identified using the node's name, with valid values listed for each
 154 of the pmics below.
 155
 156 pm8058:
 157         l0, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, l14, l15,
 158         l16, l17, l18, l19, l20, l21, l22, l23, l24, l25, s0, s1, s2, s3, s4,
 159         lvs0, lvs1, ncp
 160
 161 pm8901:
 162         l0, l1, l2, l3, l4, l5, l6, s0, s1, s2, s3, s4, lvs0, lvs1, lvs2, lvs3,
 163         mvs
 164
 165 pm8921:
 166         s1, s2, s3, s4, s7, s8, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11,
 167         l12, l14, l15, l16, l17, l18, l21, l22, l23, l24, l25, l26, l27, l28,
 168         l29, lvs1, lvs2, lvs3, lvs4, lvs5, lvs6, lvs7, usb-switch, hdmi-switch,
 169         ncp
 170
 171 pm8018:
 172         s1, s2, s3, s4, s5, , l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11,
 173         l12, l14, lvs1
 174
 175 smb208:
 176         s1a, s1b, s2a, s2b
 177
 178 The content of each sub-node is defined by the standard binding for regulators -
 179 see regulator.txt - with additional custom properties described below:
 180
 181 === Switch-mode Power Supply regulator custom properties
 182
 183 - bias-pull-down:
 184         Usage: optional
 185         Value type: <empty>
 186         Definition: enable pull down of the regulator when inactive
 187
 188 - qcom,switch-mode-frequency:
 189         Usage: required
 190         Value type: <u32>
 191         Definition: Frequency (Hz) of the switch-mode power supply;
 192                     must be one of:
 193                     19200000, 9600000, 6400000, 4800000, 3840000, 3200000,
 194                     2740000, 2400000, 2130000, 1920000, 1750000, 1600000,
 195                     1480000, 1370000, 1280000, 1200000
 196
 197 - qcom,force-mode:
 198         Usage: optional (default if no other qcom,force-mode is specified)
 199         Value type: <u32>
 200         Definition: indicates that the regulator should be forced to a
 201                    particular mode, valid values are:
 202                    QCOM_RPM_FORCE_MODE_NONE - do not force any mode
 203                    QCOM_RPM_FORCE_MODE_LPM - force into low power mode
 204                    QCOM_RPM_FORCE_MODE_HPM - force into high power mode
 205                    QCOM_RPM_FORCE_MODE_AUTO - allow regulator to automatically
 206                                               select its own mode based on
 207                                               realtime current draw, only for:
 208                                               pm8921 smps and ftsmps
 209
 210 - qcom,power-mode-hysteretic:
 211         Usage: optional
 212         Value type: <empty>
 213         Definition: select that the power supply should operate in hysteretic
 214                     mode, instead of the default pwm mode
 215
 216 === Low-dropout regulator custom properties
 217
 218 - bias-pull-down:
 219         Usage: optional
 220         Value type: <empty>
 221         Definition: enable pull down of the regulator when inactive
 222
 223 - qcom,force-mode:
 224         Usage: optional
 225         Value type: <u32>
 226         Definition: indicates that the regulator should not be forced to any
 227                    particular mode, valid values are:
 228                    QCOM_RPM_FORCE_MODE_NONE - do not force any mode
 229                    QCOM_RPM_FORCE_MODE_LPM - force into low power mode
 230                    QCOM_RPM_FORCE_MODE_HPM - force into high power mode
 231                    QCOM_RPM_FORCE_MODE_BYPASS - set regulator to use bypass
 232                                                 mode, i.e.  to act as a switch
 233                                                 and not regulate, only for:
 234                                                 pm8921 pldo, nldo and nldo1200
 235
 236 === Negative Charge Pump custom properties
 237
 238 - qcom,switch-mode-frequency:
 239         Usage: required
 240         Value type: <u32>
 241         Definition: Frequency (Hz) of the switch mode power supply;
 242                     must be one of:
 243                     19200000, 9600000, 6400000, 4800000, 3840000, 3200000,
 244                     2740000, 2400000, 2130000, 1920000, 1750000, 1600000,
 245                     1480000, 1370000, 1280000, 1200000
 246
 247 = EXAMPLE
 248
 249         #include <dt-bindings/mfd/qcom-rpm.h>
 250
 251         rpm@108000 {
 252                 compatible = "qcom,rpm-msm8960";
 253                 reg = <0x108000 0x1000>;
 254                 qcom,ipc = <&apcs 0x8 2>;
 255
 256                 interrupts = <0 19 0>, <0 21 0>, <0 22 0>;
 257                 interrupt-names = "ack", "err", "wakeup";
 258
 259                 regulators {
 260                         compatible = "qcom,rpm-pm8921-regulators";
 261                         vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
 262
 263                         s1 {
 264                                 regulator-min-microvolt = <1225000>;
 265                                 regulator-max-microvolt = <1225000>;
 266
 267                                 bias-pull-down;
 268
 269                                 qcom,switch-mode-frequency = <3200000>;
 270                         };
 271
 272                         pm8921_s4: s4 {
 273                                 regulator-min-microvolt = <1800000>;
 274                                 regulator-max-microvolt = <1800000>;
 275
 276                                 qcom,switch-mode-frequency = <1600000>;
 277                                 bias-pull-down;
 278
 279                                 qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
 280                         };
 281                 };
 282         };
 283