1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
4 $id: http://devicetree.org/schemas/pinctrl/qcom,sc8180x-pinctrl.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Qualcomm Technologies, Inc. SC8180X TLMM block
10 - Bjorn Andersson <bjorn.andersson@linaro.org>
13 This binding describes the Top Level Mode Multiplexer block found in the
17 - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
21 const: qcom,sc8180x-tlmm
33 interrupt-controller: true
34 '#interrupt-cells': true
36 gpio-reserved-ranges: true
46 additionalProperties: false
51 - $ref: "#/$defs/qcom-sc8180x-tlmm-state"
54 $ref: "#/$defs/qcom-sc8180x-tlmm-state"
57 qcom-sc8180x-tlmm-state:
60 Pinctrl node's client devices use subnodes for desired pin configuration.
61 Client device subnodes use below standard properties.
62 $ref: "qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state"
67 List of gpio pins affected by the properties specified in this
71 - pattern: "^gpio([0-9]|[1-9][0-9]|1[0-8][0-9])$"
72 - enum: [ sdc2_clk, sdc2_cmd, sdc2_data, ufs_reset ]
78 Specify the alternative function to be configured for the specified
81 enum: [ adsp_ext, agera_pll, aoss_cti, atest_char, atest_tsens,
82 atest_tsens2, atest_usb0, atest_usb1, atest_usb2, atest_usb3,
83 atest_usb4, audio_ref, btfm_slimbus, cam_mclk, cci_async,
84 cci_i2c, cci_timer0, cci_timer1, cci_timer2, cci_timer3,
85 cci_timer4, cci_timer5, cci_timer6, cci_timer7, cci_timer8,
86 cci_timer9, cri_trng, dbg_out, ddr_bist, ddr_pxi, debug_hot,
87 dp_hot, edp_hot, edp_lcd, emac_phy, emac_pps, gcc_gp1, gcc_gp2,
88 gcc_gp3, gcc_gp4, gcc_gp5, gpio, gps, grfc, hs1_mi2s, hs2_mi2s,
89 hs3_mi2s, jitter_bist, lpass_slimbus, m_voc, mdp_vsync,
90 mdp_vsync0, mdp_vsync1, mdp_vsync2, mdp_vsync3, mdp_vsync4,
91 mdp_vsync5, mss_lte, nav_pps, pa_indicator, pci_e0, pci_e1,
92 pci_e2, pci_e3, phase_flag, pll_bist, pll_bypassnl, pll_reset,
93 pri_mi2s, pri_mi2s_ws, prng_rosc, qdss_cti, qdss_gpio, qlink,
94 qspi0, qspi0_clk, qspi0_cs, qspi1, qspi1_clk, qspi1_cs,
95 qua_mi2s, qup0, qup1, qup2, qup3, qup4, qup5, qup6, qup7, qup8,
96 qup9, qup10, qup11, qup12, qup13, qup14, qup15, qup16, qup17,
97 qup18, qup19, qup_l4, qup_l5, qup_l6, rgmii, sd_write, sdc4,
98 sdc4_clk, sdc4_cmd, sec_mi2s, sp_cmu, spkr_i2s, ter_mi2s, tgu,
99 tsense_pwm1, tsense_pwm2, tsif1, tsif2, uim1, uim2, uim_batt,
100 usb0_phy, usb1_phy, usb2phy_ac, vfr_1, vsense_trigger,
101 wlan1_adc, wlan2_adc, wmss_reset ]
115 additionalProperties: false
119 #include <dt-bindings/interrupt-controller/arm-gic.h>
121 compatible = "qcom,sc8180x-tlmm";
122 reg = <0x03100000 0x300000>,
123 <0x03500000 0x700000>,
124 <0x03d00000 0x300000>;
125 reg-names = "west", "east", "south";
126 interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
129 interrupt-controller;
130 #interrupt-cells = <2>;
131 gpio-ranges = <&tlmm 0 0 190>;
133 gpio-wo-subnode-state {
138 uart-w-subnodes-state {