Documentation/md.txt

   1 Tools that manage md devices can be found at
   2    http://www.<country>.kernel.org/pub/linux/utils/raid/....
   3
   4
   5 Boot time assembly of RAID arrays
   6 ---------------------------------
   7
   8 You can boot with your md device with the following kernel command
   9 lines:
  10
  11 for old raid arrays without persistent superblocks:
  12   md=<md device no.>,<raid level>,<chunk size factor>,<fault level>,dev0,dev1,...,devn
  13
  14 for raid arrays with persistent superblocks
  15   md=<md device no.>,dev0,dev1,...,devn
  16 or, to assemble a partitionable array:
  17   md=d<md device no.>,dev0,dev1,...,devn
  18
  19 md device no. = the number of the md device ...
  20               0 means md0,
  21               1 md1,
  22               2 md2,
  23               3 md3,
  24               4 md4
  25
  26 raid level = -1 linear mode
  27               0 striped mode
  28               other modes are only supported with persistent super blocks
  29
  30 chunk size factor = (raid-0 and raid-1 only)
  31               Set  the chunk size as 4k << n.
  32
  33 fault level = totally ignored
  34
  35 dev0-devn: e.g. /dev/hda1,/dev/hdc1,/dev/sda1,/dev/sdb1
  36
  37 A possible loadlin line (Harald Hoyer <HarryH@Royal.Net>)  looks like this:
  38
  39 e:\loadlin\loadlin e:\zimage root=/dev/md0 md=0,0,4,0,/dev/hdb2,/dev/hdc3 ro
  40
  41
  42 Boot time autodetection of RAID arrays
  43 --------------------------------------
  44
  45 When md is compiled into the kernel (not as module), partitions of
  46 type 0xfd are scanned and automatically assembled into RAID arrays.
  47 This autodetection may be suppressed with the kernel parameter
  48 "raid=noautodetect".  As of kernel 2.6.9, only drives with a type 0
  49 superblock can be autodetected and run at boot time.
  50
  51 The kernel parameter "raid=partitionable" (or "raid=part") means
  52 that all auto-detected arrays are assembled as partitionable.
  53
  54 Boot time assembly of degraded/dirty arrays
  55 -------------------------------------------
  56
  57 If a raid5 or raid6 array is both dirty and degraded, it could have
  58 undetectable data corruption.  This is because the fact that it is
  59 'dirty' means that the parity cannot be trusted, and the fact that it
  60 is degraded means that some datablocks are missing and cannot reliably
  61 be reconstructed (due to no parity).
  62
  63 For this reason, md will normally refuse to start such an array.  This
  64 requires the sysadmin to take action to explicitly start the array
  65 desipite possible corruption.  This is normally done with
  66    mdadm --assemble --force ....
  67
  68 This option is not really available if the array has the root
  69 filesystem on it.  In order to support this booting from such an
  70 array, md supports a module parameter "start_dirty_degraded" which,
  71 when set to 1, bypassed the checks and will allows dirty degraded
  72 arrays to be started.
  73
  74 So, to boot with a root filesystem of a dirty degraded raid[56], use
  75
  76    md-mod.start_dirty_degraded=1
  77
  78
  79 Superblock formats
  80 ------------------
  81
  82 The md driver can support a variety of different superblock formats.
  83 Currently, it supports superblock formats "0.90.0" and the "md-1" format
  84 introduced in the 2.5 development series.
  85
  86 The kernel will autodetect which format superblock is being used.
  87
  88 Superblock format '0' is treated differently to others for legacy
  89 reasons - it is the original superblock format.
  90
  91
  92 General Rules - apply for all superblock formats
  93 ------------------------------------------------
  94
  95 An array is 'created' by writing appropriate superblocks to all
  96 devices.
  97
  98 It is 'assembled' by associating each of these devices with an
  99 particular md virtual device.  Once it is completely assembled, it can
 100 be accessed.
 101
 102 An array should be created by a user-space tool.  This will write
 103 superblocks to all devices.  It will usually mark the array as
 104 'unclean', or with some devices missing so that the kernel md driver
 105 can create appropriate redundancy (copying in raid1, parity
 106 calculation in raid4/5).
 107
 108 When an array is assembled, it is first initialized with the
 109 SET_ARRAY_INFO ioctl.  This contains, in particular, a major and minor
 110 version number.  The major version number selects which superblock
 111 format is to be used.  The minor number might be used to tune handling
 112 of the format, such as suggesting where on each device to look for the
 113 superblock.
 114
 115 Then each device is added using the ADD_NEW_DISK ioctl.  This
 116 provides, in particular, a major and minor number identifying the
 117 device to add.
 118
 119 The array is started with the RUN_ARRAY ioctl.
 120
 121 Once started, new devices can be added.  They should have an
 122 appropriate superblock written to them, and then passed be in with
 123 ADD_NEW_DISK.
 124
 125 Devices that have failed or are not yet active can be detached from an
 126 array using HOT_REMOVE_DISK.
 127
 128
 129 Specific Rules that apply to format-0 super block arrays, and
 130        arrays with no superblock (non-persistent).
 131 -------------------------------------------------------------
 132
 133 An array can be 'created' by describing the array (level, chunksize
 134 etc) in a SET_ARRAY_INFO ioctl.  This must has major_version==0 and
 135 raid_disks != 0.
 136
 137 Then uninitialized devices can be added with ADD_NEW_DISK.  The
 138 structure passed to ADD_NEW_DISK must specify the state of the device
 139 and it's role in the array.
 140
 141 Once started with RUN_ARRAY, uninitialized spares can be added with
 142 HOT_ADD_DISK.
 143
 144
 145
 146 MD devices in sysfs
 147 -------------------
 148 md devices appear in sysfs (/sys) as regular block devices,
 149 e.g.
 150    /sys/block/md0
 151
 152 Each 'md' device will contain a subdirectory called 'md' which
 153 contains further md-specific information about the device.
 154
 155 All md devices contain:
 156   level
 157      a text file indicating the 'raid level'.  This may be a standard
 158      numerical level prefixed by "RAID-" - e.g. "RAID-5", or some
 159      other name such as "linear" or "multipath".
 160      If no raid level has been set yet (array is still being
 161      assembled), this file will be empty.
 162
 163   raid_disks
 164      a text file with a simple number indicating the number of devices
 165      in a fully functional array.  If this is not yet known, the file
 166      will be empty.  If an array is being resized (not currently
 167      possible) this will contain the larger of the old and new sizes.
 168
 169 As component devices are added to an md array, they appear in the 'md'
 170 directory as new directories named
 171       dev-XXX
 172 where XXX is a name that the kernel knows for the device, e.g. hdb1.
 173 Each directory contains:
 174
 175       block
 176         a symlink to the block device in /sys/block, e.g.
 177              /sys/block/md0/md/dev-hdb1/block -> ../../../../block/hdb/hdb1
 178
 179       super
 180         A file containing an image of the superblock read from, or
 181         written to, that device.
 182
 183       state
 184         A file recording the current state of the device in the array
 185         which can be a comma separated list of
 186               faulty   - device has been kicked from active use due to
 187                          a detected fault
 188               in_sync  - device is a fully in-sync member of the array
 189               spare    - device is working, but not a full member.
 190                          This includes spares that are in the process
 191                          of being recoverred to
 192         This list make grow in future.
 193
 194
 195 An active md device will also contain and entry for each active device
 196 in the array.  These are named
 197
 198     rdNN
 199
 200 where 'NN' is the possition in the array, starting from 0.
 201 So for a 3 drive array there will be rd0, rd1, rd2.
 202 These are symbolic links to the appropriate 'dev-XXX' entry.
 203 Thus, for example,
 204        cat /sys/block/md*/md/rd*/state
 205 will show 'in_sync' on every line.
 206
 207
 208
 209 Active md devices for levels that support data redundancy (1,4,5,6)
 210 also have
 211
 212    sync_action
 213      a text file that can be used to monitor and control the rebuild
 214      process.  It contains one word which can be one of:
 215        resync        - redundancy is being recalculated after unclean
 216                        shutdown or creation
 217        recover       - a hot spare is being built to replace a
 218                        failed/missing device
 219        idle          - nothing is happening
 220        check         - A full check of redundancy was requested and is
 221                        happening.  This reads all block and checks
 222                        them. A repair may also happen for some raid
 223                        levels.
 224        repair        - A full check and repair is happening.  This is
 225                        similar to 'resync', but was requested by the
 226                        user, and the write-intent bitmap is NOT used to
 227                        optimise the process.
 228
 229       This file is writable, and each of the strings that could be
 230       read are meaningful for writing.
 231
 232        'idle' will stop an active resync/recovery etc.  There is no
 233            guarantee that another resync/recovery may not be automatically
 234            started again, though some event will be needed to trigger
 235            this.
 236         'resync' or 'recovery' can be used to restart the
 237            corresponding operation if it was stopped with 'idle'.
 238         'check' and 'repair' will start the appropriate process
 239            providing the current state is 'idle'.
 240
 241    mismatch_count
 242       When performing 'check' and 'repair', and possibly when
 243       performing 'resync', md will count the number of errors that are
 244       found.  The count in 'mismatch_cnt' is the number of sectors
 245       that were re-written, or (for 'check') would have been
 246       re-written.  As most raid levels work in units of pages rather
 247       than sectors, this my be larger than the number of actual errors
 248       by a factor of the number of sectors in a page.
 249
 250 Each active md device may also have attributes specific to the
 251 personality module that manages it.
 252 These are specific to the implementation of the module and could
 253 change substantially if the implementation changes.
 254
 255 These currently include
 256
 257   stripe_cache_size  (currently raid5 only)
 258       number of entries in the stripe cache.  This is writable, but
 259       there are upper and lower limits (32768, 16).  Default is 128.
 260   strip_cache_active (currently raid5 only)
 261       number of active entries in the stripe cache