Documentation/parisc/registers

   1 Register Usage for Linux/PA-RISC
   2
   3 [ an asterisk is used for planned usage which is currently unimplemented ]
   4
   5         General Registers as specified by ABI
   6
   7         Control Registers
   8
   9 CR 0 (Recovery Counter)         used for ptrace
  10 CR 1-CR 7(undefined)            unused
  11 CR 8 (Protection ID)            per-process value*
  12 CR 9, 12, 13 (PIDS)             unused
  13 CR10 (CCR)                      lazy FPU saving*
  14 CR11                            as specified by ABI (SAR)
  15 CR14 (interruption vector)      initialized to fault_vector
  16 CR15 (EIEM)                     initialized to all ones*
  17 CR16 (Interval Timer)           read for cycle count/write starts Interval Tmr
  18 CR17-CR22                       interruption parameters
  19 CR19                            Interrupt Instruction Register
  20 CR20                            Interrupt Space Register
  21 CR21                            Interrupt Offset Register
  22 CR22                            Interrupt PSW
  23 CR23 (EIRR)                     read for pending interrupts/write clears bits
  24 CR24 (TR 0)                     Kernel Space Page Directory Pointer
  25 CR25 (TR 1)                     User   Space Page Directory Pointer
  26 CR26 (TR 2)                     not used
  27 CR27 (TR 3)                     Thread descriptor pointer
  28 CR28 (TR 4)                     not used
  29 CR29 (TR 5)                     not used
  30 CR30 (TR 6)                     current / 0
  31 CR31 (TR 7)                     Temporary register, used in various places
  32
  33         Space Registers (kernel mode)
  34
  35 SR0                             temporary space register
  36 SR4-SR7                         set to 0
  37 SR1                             temporary space register
  38 SR2                             kernel should not clobber this
  39 SR3                             used for userspace accesses (current process)
  40
  41         Space Registers (user mode)
  42
  43 SR0                             temporary space register
  44 SR1                             temporary space register
  45 SR2                             holds space of linux gateway page
  46 SR3                             holds user address space value while in kernel
  47 SR4-SR7                         Defines short address space for user/kernel
  48
  49
  50         Processor Status Word
  51
  52 W (64-bit addresses)            0
  53 E (Little-endian)               0
  54 S (Secure Interval Timer)       0
  55 T (Taken Branch Trap)           0
  56 H (Higher-privilege trap)       0
  57 L (Lower-privilege trap)        0
  58 N (Nullify next instruction)    used by C code
  59 X (Data memory break disable)   0
  60 B (Taken Branch)                used by C code
  61 C (code address translation)    1, 0 while executing real-mode code
  62 V (divide step correction)      used by C code
  63 M (HPMC mask)                   0, 1 while executing HPMC handler*
  64 C/B (carry/borrow bits)         used by C code
  65 O (ordered references)          1*
  66 F (performance monitor)         0
  67 R (Recovery Counter trap)       0
  68 Q (collect interruption state)  1 (0 in code directly preceding an rfi)
  69 P (Protection Identifiers)      1*
  70 D (Data address translation)    1, 0 while executing real-mode code
  71 I (external interrupt mask)     used by cli()/sti() macros
  72
  73         "Invisible" Registers
  74
  75 PSW default W value             0
  76 PSW default E value             0
  77 Shadow Registers                used by interruption handler code
  78 TOC enable bit                  1
  79
  80 =========================================================================
  81 Register usage notes, originally from John Marvin, with some additional
  82 notes from Randolph Chung.
  83
  84 For the general registers:
  85
  86 r1,r2,r19-r26,r28,r29 & r31 can be used without saving them first. And of
  87 course, you need to save them if you care about them, before calling
  88 another procedure. Some of the above registers do have special meanings
  89 that you should be aware of:
  90
  91     r1: The addil instruction is hardwired to place its result in r1,
  92         so if you use that instruction be aware of that.
  93
  94     r2: This is the return pointer. In general you don't want to
  95         use this, since you need the pointer to get back to your
  96         caller. However, it is grouped with this set of registers
  97         since the caller can't rely on the value being the same
  98         when you return, i.e. you can copy r2 to another register
  99         and return through that register after trashing r2, and
 100         that should not cause a problem for the calling routine.
 101
 102     r19-r22: these are generally regarded as temporary registers.
 103         Note that in 64 bit they are arg7-arg4.
 104
 105     r23-r26: these are arg3-arg0, i.e. you can use them if you
 106         don't care about the values that were passed in anymore.
 107
 108     r28,r29: are ret0 and ret1. They are what you pass return values
 109         in. r28 is the primary return. When returning small structures
 110         r29 may also be used to pass data back to the caller.
 111
 112     r30: stack pointer
 113
 114     r31: the ble instruction puts the return pointer in here.
 115
 116
 117 r3-r18,r27,r30 need to be saved and restored. r3-r18 are just
 118     general purpose registers. r27 is the data pointer, and is
 119     used to make references to global variables easier. r30 is
 120     the stack pointer.
 121