1 Linux Kernel 2.6 series
2 SCSI mid_level - lower_level driver interface
3 =============================================
7 This document outlines the interface between the Linux SCSI mid level and
8 SCSI lower level drivers. Lower level drivers (LLDs) are variously called
9 host bus adapter (HBA) drivers and host drivers (HD). A "host" in this
10 context is a bridge between a computer IO bus (e.g. PCI or ISA) and a
11 single SCSI initiator port on a SCSI transport. An "initiator" port
12 (SCSI terminology, see SAM-3 at http://www.t10.org) sends SCSI commands
13 to "target" SCSI ports (e.g. disks). There can be many LLDs in a running
14 system, but only one per hardware type. Most LLDs can control one or more
15 SCSI HBAs. Some HBAs contain multiple hosts.
17 In some cases the SCSI transport is an external bus that already has
18 its own subsystem in Linux (e.g. USB and ieee1394). In such cases the
19 SCSI subsystem LLD is a software bridge to the other driver subsystem.
20 Examples are the usb-storage driver (found in the drivers/usb/storage
21 directory) and the ieee1394/sbp2 driver (found in the drivers/ieee1394
24 For example, the aic7xxx LLD controls Adaptec SCSI parallel interface
25 (SPI) controllers based on that company's 7xxx chip series. The aic7xxx
26 LLD can be built into the kernel or loaded as a module. There can only be
27 one aic7xxx LLD running in a Linux system but it may be controlling many
28 HBAs. These HBAs might be either on PCI daughter-boards or built into
29 the motherboard (or both). Some aic7xxx based HBAs are dual controllers
30 and thus represent two hosts. Like most modern HBAs, each aic7xxx host
31 has its own PCI device address. [The one-to-one correspondence between
32 a SCSI host and a PCI device is common but not required (e.g. with
33 ISA or MCA adapters).]
35 The SCSI mid level isolates an LLD from other layers such as the SCSI
36 upper layer drivers and the block layer.
38 This version of the document roughly matches linux kernel version 2.6.8 .
42 There is a SCSI documentation directory within the kernel source tree,
43 typically Documentation/scsi . Most documents are in plain
44 (i.e. ASCII) text. This file is named scsi_mid_low_api.txt and can be
45 found in that directory. A more recent copy of this document may be found
46 at http://www.torque.net/scsi/scsi_mid_low_api.txt.gz .
47 Many LLDs are documented there (e.g. aic7xxx.txt). The SCSI mid-level is
48 briefly described in scsi.txt which contains a url to a document
49 describing the SCSI subsystem in the lk 2.4 series. Two upper level
50 drivers have documents in that directory: st.txt (SCSI tape driver) and
51 scsi-generic.txt (for the sg driver).
53 Some documentation (or urls) for LLDs may be found in the C source code
54 or in the same directory as the C source code. For example to find a url
55 about the USB mass storage driver see the
56 /usr/src/linux/drivers/usb/storage directory.
58 The Linux kernel source Documentation/DocBook/scsidrivers.tmpl file
59 refers to this file. With the appropriate DocBook tool-set, this permits
60 users to generate html, ps and pdf renderings of information within this
61 file (e.g. the interface functions).
65 Traditionally an LLD for the SCSI subsystem has been at least two files in
66 the drivers/scsi directory. For example, a driver called "xyz" has a header
67 file "xyz.h" and a source file "xyz.c". [Actually there is no good reason
68 why this couldn't all be in one file; the header file is superfluous.] Some
69 drivers that have been ported to several operating systems have more than
70 two files. For example the aic7xxx driver has separate files for generic
71 and OS-specific code (e.g. FreeBSD and Linux). Such drivers tend to have
72 their own directory under the drivers/scsi directory.
74 When a new LLD is being added to Linux, the following files (found in the
75 drivers/scsi directory) will need some attention: Makefile and Kconfig .
76 It is probably best to study how existing LLDs are organized.
78 As the 2.5 series development kernels evolve into the 2.6 series
79 production series, changes are being introduced into this interface. An
80 example of this is driver initialization code where there are now 2 models
81 available. The older one, similar to what was found in the lk 2.4 series,
82 is based on hosts that are detected at HBA driver load time. This will be
83 referred to the "passive" initialization model. The newer model allows HBAs
84 to be hot plugged (and unplugged) during the lifetime of the LLD and will
85 be referred to as the "hotplug" initialization model. The newer model is
86 preferred as it can handle both traditional SCSI equipment that is
87 permanently connected as well as modern "SCSI" devices (e.g. USB or
88 IEEE 1394 connected digital cameras) that are hotplugged. Both
89 initialization models are discussed in the following sections.
91 An LLD interfaces to the SCSI subsystem several ways:
92 a) directly invoking functions supplied by the mid level
93 b) passing a set of function pointers to a registration function
94 supplied by the mid level. The mid level will then invoke these
95 functions at some point in the future. The LLD will supply
96 implementations of these functions.
97 c) direct access to instances of well known data structures maintained
100 Those functions in group a) are listed in a section entitled "Mid level
101 supplied functions" below.
103 Those functions in group b) are listed in a section entitled "Interface
104 functions" below. Their function pointers are placed in the members of
105 "struct scsi_host_template", an instance of which is passed to
106 scsi_host_alloc() ** . Those interface functions that the LLD does not
107 wish to supply should have NULL placed in the corresponding member of
108 struct scsi_host_template. Defining an instance of struct
109 scsi_host_template at file scope will cause NULL to be placed in function
110 pointer members not explicitly initialized.
112 Those usages in group c) should be handled with care, especially in a
113 "hotplug" environment. LLDs should be aware of the lifetime of instances
114 that are shared with the mid level and other layers.
116 All functions defined within an LLD and all data defined at file scope
117 should be static. For example the slave_alloc() function in an LLD
118 called "xxx" could be defined as
119 "static int xxx_slave_alloc(struct scsi_device * sdev) { /* code */ }"
121 ** the scsi_host_alloc() function is a replacement for the rather vaguely
122 named scsi_register() function in most situations. The scsi_register()
123 and scsi_unregister() functions remain to support legacy LLDs that use
124 the passive initialization model.
127 Hotplug initialization model
128 ============================
129 In this model an LLD controls when SCSI hosts are introduced and removed
130 from the SCSI subsystem. Hosts can be introduced as early as driver
131 initialization and removed as late as driver shutdown. Typically a driver
132 will respond to a sysfs probe() callback that indicates an HBA has been
133 detected. After confirming that the new device is one that the LLD wants
134 to control, the LLD will initialize the HBA and then register a new host
135 with the SCSI mid level.
137 During LLD initialization the driver should register itself with the
138 appropriate IO bus on which it expects to find HBA(s) (e.g. the PCI bus).
139 This can probably be done via sysfs. Any driver parameters (especially
140 those that are writable after the driver is loaded) could also be
141 registered with sysfs at this point. The SCSI mid level first becomes
142 aware of an LLD when that LLD registers its first HBA.
144 At some later time, the LLD becomes aware of an HBA and what follows
145 is a typical sequence of calls between the LLD and the mid level.
146 This example shows the mid level scanning the newly introduced HBA for 3
147 scsi devices of which only the first 2 respond:
149 HBA PROBE: assume 2 SCSI devices found in scan
151 ===-------------------=========--------------------===------
152 scsi_host_alloc() -->
153 scsi_add_host() --------+
156 slave_configure() --> scsi_adjust_queue_depth()
163 ------------------------------------------------------------
165 If the LLD wants to adjust the default queue settings, it can invoke
166 scsi_adjust_queue_depth() in its slave_configure() routine.
168 *** For scsi devices that the mid level tries to scan but do not
169 respond, a slave_alloc(), slave_destroy() pair is called.
171 When an HBA is being removed it could be as part of an orderly shutdown
172 associated with the LLD module being unloaded (e.g. with the "rmmod"
173 command) or in response to a "hot unplug" indicated by sysfs()'s
174 remove() callback being invoked. In either case, the sequence is the
177 HBA REMOVE: assume 2 SCSI devices attached
179 ===----------------------=========-----------------===------
180 scsi_remove_host() ---------+
185 ------------------------------------------------------------
187 It may be useful for a LLD to keep track of struct Scsi_Host instances
188 (a pointer is returned by scsi_host_alloc()). Such instances are "owned"
189 by the mid-level. struct Scsi_Host instances are freed from
190 scsi_host_put() when the reference count hits zero.
192 Hot unplugging an HBA that controls a disk which is processing SCSI
193 commands on a mounted file system is an interesting situation. Reference
194 counting logic is being introduced into the mid level to cope with many
195 of the issues involved. See the section on reference counting below.
198 The hotplug concept may be extended to SCSI devices. Currently, when an
199 HBA is added, the scsi_add_host() function causes a scan for SCSI devices
200 attached to the HBA's SCSI transport. On newer SCSI transports the HBA
201 may become aware of a new SCSI device _after_ the scan has completed.
202 An LLD can use this sequence to make the mid level aware of a SCSI device:
206 ===-------------------=========--------------------===------
207 scsi_add_device() ------+
210 slave_configure() [--> scsi_adjust_queue_depth()]
211 ------------------------------------------------------------
213 In a similar fashion, an LLD may become aware that a SCSI device has been
214 removed (unplugged) or the connection to it has been interrupted. Some
215 existing SCSI transports (e.g. SPI) may not become aware that a SCSI
216 device has been removed until a subsequent SCSI command fails which will
217 probably cause that device to be set offline by the mid level. An LLD that
218 detects the removal of a SCSI device can instigate its removal from
219 upper layers with this sequence:
221 SCSI DEVICE hot unplug
223 ===----------------------=========-----------------===------
224 scsi_remove_device() -------+
227 ------------------------------------------------------------
229 It may be useful for an LLD to keep track of struct scsi_device instances
230 (a pointer is passed as the parameter to slave_alloc() and
231 slave_configure() callbacks). Such instances are "owned" by the mid-level.
232 struct scsi_device instances are freed after slave_destroy().
235 Passive initialization model
236 ============================
237 These older LLDs include a file called "scsi_module.c" [yes the ".c" is a
238 little surprising] in their source code. For that file to work an
239 instance of struct scsi_host_template with the name "driver_template"
240 needs to be defined. Here is a typical code sequence used in this model:
241 static struct scsi_host_template driver_template = {
244 #include "scsi_module.c"
246 The scsi_module.c file contains two functions:
247 - init_this_scsi_driver() which is executed when the LLD is
248 initialized (i.e. boot time or module load time)
249 - exit_this_scsi_driver() which is executed when the LLD is shut
250 down (i.e. module unload time)
251 Note: since these functions are tagged with __init and __exit qualifiers
252 an LLD should not call them explicitly (since the kernel does that).
254 Here is an example of an initialization sequence when two hosts are
255 detected (so detect() returns 2) and the SCSI bus scan on each host
256 finds 1 SCSI device (and a second device does not respond).
259 ===----------------------=========-----------------===------
260 init_this_scsi_driver() ----+
262 detect() -----------------+
268 slave_configure() --> scsi_adjust_queue_depth()
276 ------------------------------------------------------------
278 The mid level invokes scsi_adjust_queue_depth() with tagged queuing off and
279 "cmd_per_lun" for that host as the queue length. These settings can be
280 overridden by a slave_configure() supplied by the LLD.
282 *** For scsi devices that the mid level tries to scan but do not
283 respond, a slave_alloc(), slave_destroy() pair is called.
285 Here is an LLD shutdown sequence:
288 ===----------------------=========-----------------===------
289 exit_this_scsi_driver() ----+
292 release() --> scsi_unregister()
295 release() --> scsi_unregister()
296 ------------------------------------------------------------
298 An LLD need not define slave_destroy() (i.e. it is optional).
300 The shortcoming of the "passive initialization model" is that host
301 registration and de-registration are (typically) tied to LLD initialization
302 and shutdown. Once the LLD is initialized then a new host that appears
303 (e.g. via hotplugging) cannot easily be added without a redundant
304 driver shutdown and re-initialization. It may be possible to write an LLD
305 that uses both initialization models.
310 The Scsi_Host structure has had reference counting infrastructure added.
311 This effectively spreads the ownership of struct Scsi_Host instances
312 across the various SCSI layers which use them. Previously such instances
313 were exclusively owned by the mid level. LLDs would not usually need to
314 directly manipulate these reference counts but there may be some cases
317 There are 3 reference counting functions of interest associated with
319 - scsi_host_alloc(): returns a pointer to new instance of struct
320 Scsi_Host which has its reference count ^^ set to 1
321 - scsi_host_get(): adds 1 to the reference count of the given instance
322 - scsi_host_put(): decrements 1 from the reference count of the given
323 instance. If the reference count reaches 0 then the given instance
326 The Scsi_device structure has had reference counting infrastructure added.
327 This effectively spreads the ownership of struct Scsi_device instances
328 across the various SCSI layers which use them. Previously such instances
329 were exclusively owned by the mid level. See the access functions declared
330 towards the end of include/scsi/scsi_device.h . If an LLD wants to keep
331 a copy of a pointer to a Scsi_device instance it should use scsi_device_get()
332 to bump its reference count. When it is finished with the pointer it can
333 use scsi_device_put() to decrement its reference count (and potentially
336 ^^ struct Scsi_Host actually has 2 reference counts which are manipulated
337 in parallel by these functions.
342 First, Linus Torvalds's thoughts on C coding style can be found in the
343 Documentation/CodingStyle file.
345 Next, there is a movement to "outlaw" typedefs introducing synonyms for
346 struct tags. Both can be still found in the SCSI subsystem, but
347 the typedefs have been moved to a single file, scsi_typedefs.h to
348 make their future removal easier, for example:
349 "typedef struct scsi_host_template Scsi_Host_Template;"
351 Also, most C99 enhancements are encouraged to the extent they are supported
352 by the relevant gcc compilers. So C99 style structure and array
353 initializers are encouraged where appropriate. Don't go too far,
354 VLAs are not properly supported yet. An exception to this is the use of
355 "//" style comments; /*...*/ comments are still preferred in Linux.
357 Well written, tested and documented code, need not be re-formatted to
358 comply with the above conventions. For example, the aic7xxx driver
359 comes to Linux from FreeBSD and Adaptec's own labs. No doubt FreeBSD
360 and Adaptec have their own coding conventions.
363 Mid level supplied functions
364 ============================
365 These functions are supplied by the SCSI mid level for use by LLDs.
366 The names (i.e. entry points) of these functions are exported
367 so an LLD that is a module can access them. The kernel will
368 arrange for the SCSI mid level to be loaded and initialized before any LLD
369 is initialized. The functions below are listed alphabetically and their
370 names all start with "scsi_".
373 scsi_activate_tcq - turn on tag command queueing
374 scsi_add_device - creates new scsi device (lu) instance
375 scsi_add_host - perform sysfs registration and SCSI bus scan.
376 scsi_add_timer - (re-)start timer on a SCSI command.
377 scsi_adjust_queue_depth - change the queue depth on a SCSI device
378 scsi_assign_lock - replace default host_lock with given lock
379 scsi_bios_ptable - return copy of block device's partition table
380 scsi_block_requests - prevent further commands being queued to given host
381 scsi_deactivate_tcq - turn off tag command queueing
382 scsi_delete_timer - cancel timer on a SCSI command.
383 scsi_host_alloc - return a new scsi_host instance whose refcount==1
384 scsi_host_get - increments Scsi_Host instance's refcount
385 scsi_host_put - decrements Scsi_Host instance's refcount (free if 0)
386 scsi_partsize - parse partition table into cylinders, heads + sectors
387 scsi_register - create and register a scsi host adapter instance.
388 scsi_remove_device - detach and remove a SCSI device
389 scsi_remove_host - detach and remove all SCSI devices owned by host
390 scsi_report_bus_reset - report scsi _bus_ reset observed
391 scsi_set_device - place device reference in host structure
392 scsi_to_pci_dma_dir - convert SCSI subsystem direction flag to PCI
393 scsi_to_sbus_dma_dir - convert SCSI subsystem direction flag to SBUS
394 scsi_track_queue_full - track successive QUEUE_FULL events
395 scsi_unblock_requests - allow further commands to be queued to given host
396 scsi_unregister - [calls scsi_host_put()]
402 * scsi_activate_tcq - turn on tag command queueing ("ordered" task attribute)
403 * @sdev: device to turn on TCQ for
404 * @depth: queue depth
410 * Notes: Eventually, it is hoped depth would be the maximum depth
411 * the device could cope with and the real queue depth
412 * would be adjustable from 0 to depth.
414 * Defined (inline) in: include/scsi/scsi_tcq.h
416 void scsi_activate_tcq(struct scsi_device *sdev, int depth)
420 * scsi_add_device - creates new scsi device (lu) instance
421 * @shost: pointer to scsi host instance
422 * @channel: channel number (rarely other than 0)
423 * @id: target id number
424 * @lun: logical unit number
426 * Returns pointer to new struct scsi_device instance or
427 * ERR_PTR(-ENODEV) (or some other bent pointer) if something is
428 * wrong (e.g. no lu responds at given address)
432 * Notes: This call is usually performed internally during a scsi
433 * bus scan when an HBA is added (i.e. scsi_add_host()). So it
434 * should only be called if the HBA becomes aware of a new scsi
435 * device (lu) after scsi_add_host() has completed. If successful
436 * this call we lead to slave_alloc() and slave_configure() callbacks
439 * Defined in: drivers/scsi/scsi_scan.c
441 struct scsi_device * scsi_add_device(struct Scsi_Host *shost,
442 unsigned int channel,
443 unsigned int id, unsigned int lun)
447 * scsi_add_host - perform sysfs registration and SCSI bus scan.
448 * @shost: pointer to scsi host instance
449 * @dev: pointer to struct device of type scsi class
451 * Returns 0 on success, negative errno of failure (e.g. -ENOMEM)
455 * Notes: Only required in "hotplug initialization model" after a
456 * successful call to scsi_host_alloc().
458 * Defined in: drivers/scsi/hosts.c
460 int scsi_add_host(struct Scsi_Host *shost, struct device * dev)
464 * scsi_add_timer - (re-)start timer on a SCSI command.
465 * @scmd: pointer to scsi command instance
466 * @timeout: duration of timeout in "jiffies"
467 * @complete: pointer to function to call if timeout expires
473 * Notes: Each scsi command has its own timer, and as it is added
474 * to the queue, we set up the timer. When the command completes,
475 * we cancel the timer. An LLD can use this function to change
476 * the existing timeout value.
478 * Defined in: drivers/scsi/scsi_error.c
480 void scsi_add_timer(struct scsi_cmnd *scmd, int timeout,
481 void (*complete)(struct scsi_cmnd *))
485 * scsi_adjust_queue_depth - allow LLD to change queue depth on a SCSI device
486 * @sdev: pointer to SCSI device to change queue depth on
487 * @tagged: 0 - no tagged queuing
488 * MSG_SIMPLE_TAG - simple tagged queuing
489 * MSG_ORDERED_TAG - ordered tagged queuing
490 * @tags Number of tags allowed if tagged queuing enabled,
491 * or number of commands the LLD can queue up
492 * in non-tagged mode (as per cmd_per_lun).
498 * Notes: Can be invoked any time on a SCSI device controlled by this
499 * LLD. [Specifically during and after slave_configure() and prior to
500 * slave_destroy().] Can safely be invoked from interrupt code. Actual
501 * queue depth change may be delayed until the next command is being
502 * processed. See also scsi_activate_tcq() and scsi_deactivate_tcq().
504 * Defined in: drivers/scsi/scsi.c [see source code for more notes]
507 void scsi_adjust_queue_depth(struct scsi_device * sdev, int tagged,
512 * scsi_assign_lock - replace default host_lock with given lock
513 * @shost: a pointer to a scsi host instance
514 * @lock: pointer to lock to replace host_lock for this host
520 * Defined in: include/scsi/scsi_host.h .
522 void scsi_assign_lock(struct Scsi_Host *shost, spinlock_t *lock)
526 * scsi_bios_ptable - return copy of block device's partition table
527 * @dev: pointer to block device
529 * Returns pointer to partition table, or NULL for failure
533 * Notes: Caller owns memory returned (free with kfree() )
535 * Defined in: drivers/scsi/scsicam.c
537 unsigned char *scsi_bios_ptable(struct block_device *dev)
541 * scsi_block_requests - prevent further commands being queued to given host
543 * @shost: pointer to host to block commands on
549 * Notes: There is no timer nor any other means by which the requests
550 * get unblocked other than the LLD calling scsi_unblock_requests().
552 * Defined in: drivers/scsi/scsi_lib.c
554 void scsi_block_requests(struct Scsi_Host * shost)
558 * scsi_deactivate_tcq - turn off tag command queueing
559 * @sdev: device to turn off TCQ for
560 * @depth: queue depth (stored in sdev)
566 * Defined (inline) in: include/scsi/scsi_tcq.h
568 void scsi_deactivate_tcq(struct scsi_device *sdev, int depth)
572 * scsi_delete_timer - cancel timer on a SCSI command.
573 * @scmd: pointer to scsi command instance
575 * Returns 1 if able to cancel timer else 0 (i.e. too late or already
578 * Might block: no [may in the future if it invokes del_timer_sync()]
580 * Notes: All commands issued by upper levels already have a timeout
581 * associated with them. An LLD can use this function to cancel the
584 * Defined in: drivers/scsi/scsi_error.c
586 int scsi_delete_timer(struct scsi_cmnd *scmd)
590 * scsi_host_alloc - create a scsi host adapter instance and perform basic
592 * @sht: pointer to scsi host template
593 * @privsize: extra bytes to allocate in hostdata array (which is the
594 * last member of the returned Scsi_Host instance)
596 * Returns pointer to new Scsi_Host instance or NULL on failure
600 * Notes: When this call returns to the LLD, the SCSI bus scan on
601 * this host has _not_ yet been done.
602 * The hostdata array (by default zero length) is a per host scratch
603 * area for the LLD's exclusive use.
604 * Both associated refcounting objects have their refcount set to 1.
605 * Full registration (in sysfs) and a bus scan are performed later when
606 * scsi_add_host() is called.
608 * Defined in: drivers/scsi/hosts.c .
610 struct Scsi_Host * scsi_host_alloc(struct scsi_host_template * sht,
615 * scsi_host_get - increment Scsi_Host instance refcount
616 * @shost: pointer to struct Scsi_Host instance
620 * Might block: currently may block but may be changed to not block
622 * Notes: Actually increments the counts in two sub-objects
624 * Defined in: drivers/scsi/hosts.c
626 void scsi_host_get(struct Scsi_Host *shost)
630 * scsi_host_put - decrement Scsi_Host instance refcount, free if 0
631 * @shost: pointer to struct Scsi_Host instance
635 * Might block: currently may block but may be changed to not block
637 * Notes: Actually decrements the counts in two sub-objects. If the
638 * latter refcount reaches 0, the Scsi_Host instance is freed.
639 * The LLD need not worry exactly when the Scsi_Host instance is
640 * freed, it just shouldn't access the instance after it has balanced
641 * out its refcount usage.
643 * Defined in: drivers/scsi/hosts.c
645 void scsi_host_put(struct Scsi_Host *shost)
649 * scsi_partsize - parse partition table into cylinders, heads + sectors
650 * @buf: pointer to partition table
651 * @capacity: size of (total) disk in 512 byte sectors
652 * @cyls: outputs number of cylinders calculated via this pointer
653 * @hds: outputs number of heads calculated via this pointer
654 * @secs: outputs number of sectors calculated via this pointer
656 * Returns 0 on success, -1 on failure
660 * Notes: Caller owns memory returned (free with kfree() )
662 * Defined in: drivers/scsi/scsicam.c
664 int scsi_partsize(unsigned char *buf, unsigned long capacity,
665 unsigned int *cyls, unsigned int *hds, unsigned int *secs)
669 * scsi_register - create and register a scsi host adapter instance.
670 * @sht: pointer to scsi host template
671 * @privsize: extra bytes to allocate in hostdata array (which is the
672 * last member of the returned Scsi_Host instance)
674 * Returns pointer to new Scsi_Host instance or NULL on failure
678 * Notes: When this call returns to the LLD, the SCSI bus scan on
679 * this host has _not_ yet been done.
680 * The hostdata array (by default zero length) is a per host scratch
683 * Defined in: drivers/scsi/hosts.c .
685 struct Scsi_Host * scsi_register(struct scsi_host_template * sht,
690 * scsi_remove_device - detach and remove a SCSI device
691 * @sdev: a pointer to a scsi device instance
693 * Returns value: 0 on success, -EINVAL if device not attached
697 * Notes: If an LLD becomes aware that a scsi device (lu) has
698 * been removed but its host is still present then it can request
699 * the removal of that scsi device. If successful this call will
700 * lead to the slave_destroy() callback being invoked. sdev is an
701 * invalid pointer after this call.
703 * Defined in: drivers/scsi/scsi_sysfs.c .
705 int scsi_remove_device(struct scsi_device *sdev)
709 * scsi_remove_host - detach and remove all SCSI devices owned by host
710 * @shost: a pointer to a scsi host instance
712 * Returns value: 0 on success, 1 on failure (e.g. LLD busy ??)
716 * Notes: Should only be invoked if the "hotplug initialization
717 * model" is being used. It should be called _prior_ to
720 * Defined in: drivers/scsi/hosts.c .
722 int scsi_remove_host(struct Scsi_Host *shost)
726 * scsi_report_bus_reset - report scsi _bus_ reset observed
727 * @shost: a pointer to a scsi host involved
728 * @channel: channel (within) host on which scsi bus reset occurred
734 * Notes: This only needs to be called if the reset is one which
735 * originates from an unknown location. Resets originated by the
736 * mid level itself don't need to call this, but there should be
737 * no harm. The main purpose of this is to make sure that a
738 * CHECK_CONDITION is properly treated.
740 * Defined in: drivers/scsi/scsi_error.c .
742 void scsi_report_bus_reset(struct Scsi_Host * shost, int channel)
746 * scsi_set_device - place device reference in host structure
747 * @shost: a pointer to a scsi host instance
748 * @pdev: pointer to device instance to assign
754 * Defined in: include/scsi/scsi_host.h .
756 void scsi_set_device(struct Scsi_Host * shost, struct device * dev)
760 * scsi_to_pci_dma_dir - convert SCSI subsystem direction flag to PCI
761 * @scsi_data_direction: SCSI subsystem direction flag
763 * Returns DMA_TO_DEVICE given SCSI_DATA_WRITE,
764 * DMA_FROM_DEVICE given SCSI_DATA_READ
765 * DMA_BIDIRECTIONAL given SCSI_DATA_UNKNOWN
766 * else returns DMA_NONE
770 * Notes: The SCSI subsystem now uses the same values for these
771 * constants as the PCI subsystem so this function is a nop.
772 * The recommendation is not to use this conversion function anymore
773 * (in the 2.6 kernel series) as it is not needed.
775 * Defined in: drivers/scsi/scsi.h .
777 int scsi_to_pci_dma_dir(unsigned char scsi_data_direction)
781 * scsi_to_sbus_dma_dir - convert SCSI subsystem direction flag to SBUS
782 * @scsi_data_direction: SCSI subsystem direction flag
784 * Returns DMA_TO_DEVICE given SCSI_DATA_WRITE,
785 * FROM_DEVICE given SCSI_DATA_READ
786 * DMA_BIDIRECTIONAL given SCSI_DATA_UNKNOWN
787 * else returns DMA_NONE
789 * Notes: The SCSI subsystem now uses the same values for these
790 * constants as the SBUS subsystem so this function is a nop.
791 * The recommendation is not to use this conversion function anymore
792 * (in the 2.6 kernel series) as it is not needed.
796 * Defined in: drivers/scsi/scsi.h .
798 int scsi_to_sbus_dma_dir(unsigned char scsi_data_direction)
802 * scsi_track_queue_full - track successive QUEUE_FULL events on given
803 * device to determine if and when there is a need
804 * to adjust the queue depth on the device.
805 * @sdev: pointer to SCSI device instance
806 * @depth: Current number of outstanding SCSI commands on this device,
807 * not counting the one returned as QUEUE_FULL.
809 * Returns 0 - no change needed
810 * >0 - adjust queue depth to this new depth
811 * -1 - drop back to untagged operation using host->cmd_per_lun
812 * as the untagged command depth
816 * Notes: LLDs may call this at any time and we will do "The Right
817 * Thing"; interrupt context safe.
819 * Defined in: drivers/scsi/scsi.c .
821 int scsi_track_queue_full(Scsi_Device *sdev, int depth)
825 * scsi_unblock_requests - allow further commands to be queued to given host
827 * @shost: pointer to host to unblock commands on
833 * Defined in: drivers/scsi/scsi_lib.c .
835 void scsi_unblock_requests(struct Scsi_Host * shost)
839 * scsi_unregister - unregister and free memory used by host instance
840 * @shp: pointer to scsi host instance to unregister.
846 * Notes: Should not be invoked if the "hotplug initialization
847 * model" is being used. Called internally by exit_this_scsi_driver()
848 * in the "passive initialization model". Hence a LLD has no need to
849 * call this function directly.
851 * Defined in: drivers/scsi/hosts.c .
853 void scsi_unregister(struct Scsi_Host * shp)
860 Interface functions are supplied (defined) by LLDs and their function
861 pointers are placed in an instance of struct scsi_host_template which
862 is passed to scsi_host_alloc() [or scsi_register() / init_this_scsi_driver()].
863 Some are mandatory. Interface functions should be declared static. The
864 accepted convention is that driver "xyz" will declare its slave_configure()
866 static int xyz_slave_configure(struct scsi_device * sdev);
867 and so forth for all interface functions listed below.
869 A pointer to this function should be placed in the 'slave_configure' member
870 of a "struct scsi_host_template" instance. A pointer to such an instance
871 should be passed to the mid level's scsi_host_alloc() [or scsi_register() /
872 init_this_scsi_driver()].
874 The interface functions are also described in the include/scsi/scsi_host.h
875 file immediately above their definition point in "struct scsi_host_template".
876 In some cases more detail is given in scsi_host.h than below.
878 The interface functions are listed below in alphabetical order.
881 bios_param - fetch head, sector, cylinder info for a disk
882 detect - detects HBAs this driver wants to control
883 eh_timed_out - notify the host that a command timer expired
884 eh_abort_handler - abort given command
885 eh_bus_reset_handler - issue SCSI bus reset
886 eh_device_reset_handler - issue SCSI device reset
887 eh_host_reset_handler - reset host (host bus adapter)
888 eh_strategy_handler - driver supplied alternate to scsi_unjam_host()
889 info - supply information about given host
890 ioctl - driver can respond to ioctls
891 proc_info - supports /proc/scsi/{driver_name}/{host_no}
892 queuecommand - queue scsi command, invoke 'done' on completion
893 release - release all resources associated with given host
894 slave_alloc - prior to any commands being sent to a new device
895 slave_configure - driver fine tuning for given device after attach
896 slave_destroy - given device is about to be shut down
902 * bios_param - fetch head, sector, cylinder info for a disk
903 * @sdev: pointer to scsi device context (defined in
904 * include/scsi/scsi_device.h)
905 * @bdev: pointer to block device context (defined in fs.h)
906 * @capacity: device size (in 512 byte sectors)
907 * @params: three element array to place output:
908 * params[0] number of heads (max 255)
909 * params[1] number of sectors (max 63)
910 * params[2] number of cylinders
912 * Return value is ignored
916 * Calling context: process (sd)
918 * Notes: an arbitrary geometry (based on READ CAPACITY) is used
919 * if this function is not provided. The params array is
920 * pre-initialized with made up values just in case this function
921 * doesn't output anything.
923 * Optionally defined in: LLD
925 int bios_param(struct scsi_device * sdev, struct block_device *bdev,
926 sector_t capacity, int params[3])
930 * detect - detects HBAs this driver wants to control
931 * @shtp: host template for this driver.
933 * Returns number of hosts this driver wants to control. 0 means no
934 * suitable hosts found.
938 * Calling context: process [invoked from init_this_scsi_driver()]
940 * Notes: First function called from the SCSI mid level on this
941 * driver. Upper level drivers (e.g. sd) may not (yet) be present.
942 * For each host found, this method should call scsi_register()
945 * Defined in: LLD (required if "passive initialization mode" is used,
946 * not invoked in "hotplug initialization mode")
948 int detect(struct scsi_host_template * shtp)
952 * eh_timed_out - The timer for the command has just fired
953 * @scp: identifies command timing out
957 * EH_HANDLED: I fixed the error, please complete the command
958 * EH_RESET_TIMER: I need more time, reset the timer and
959 * begin counting again
960 * EH_NOT_HANDLED Begin normal error recovery
965 * Calling context: interrupt
967 * Notes: This is to give the LLD an opportunity to do local recovery.
968 * This recovery is limited to determining if the outstanding command
969 * will ever complete. You may not abort and restart the command from
972 * Optionally defined in: LLD
974 int eh_timed_out(struct scsi_cmnd * scp)
978 * eh_abort_handler - abort command associated with scp
979 * @scp: identifies command to be aborted
981 * Returns SUCCESS if command aborted else FAILED
983 * Locks: struct Scsi_Host::host_lock held (with irqsave) on entry
984 * and assumed to be held on return.
986 * Calling context: kernel thread
988 * Notes: Invoked from scsi_eh thread. No other commands will be
989 * queued on current host during eh.
991 * Optionally defined in: LLD
993 int eh_abort_handler(struct scsi_cmnd * scp)
997 * eh_bus_reset_handler - issue SCSI bus reset
998 * @scp: SCSI bus that contains this device should be reset
1000 * Returns SUCCESS if command aborted else FAILED
1002 * Locks: struct Scsi_Host::host_lock held (with irqsave) on entry
1003 * and assumed to be held on return.
1005 * Calling context: kernel thread
1007 * Notes: Invoked from scsi_eh thread. No other commands will be
1008 * queued on current host during eh.
1010 * Optionally defined in: LLD
1012 int eh_bus_reset_handler(struct scsi_cmnd * scp)
1016 * eh_device_reset_handler - issue SCSI device reset
1017 * @scp: identifies SCSI device to be reset
1019 * Returns SUCCESS if command aborted else FAILED
1021 * Locks: struct Scsi_Host::host_lock held (with irqsave) on entry
1022 * and assumed to be held on return.
1024 * Calling context: kernel thread
1026 * Notes: Invoked from scsi_eh thread. No other commands will be
1027 * queued on current host during eh.
1029 * Optionally defined in: LLD
1031 int eh_device_reset_handler(struct scsi_cmnd * scp)
1035 * eh_host_reset_handler - reset host (host bus adapter)
1036 * @scp: SCSI host that contains this device should be reset
1038 * Returns SUCCESS if command aborted else FAILED
1040 * Locks: struct Scsi_Host::host_lock held (with irqsave) on entry
1041 * and assumed to be held on return.
1043 * Calling context: kernel thread
1045 * Notes: Invoked from scsi_eh thread. No other commands will be
1046 * queued on current host during eh.
1047 * With the default eh_strategy in place, if none of the _abort_,
1048 * _device_reset_, _bus_reset_ or this eh handler function are
1049 * defined (or they all return FAILED) then the device in question
1050 * will be set offline whenever eh is invoked.
1052 * Optionally defined in: LLD
1054 int eh_host_reset_handler(struct scsi_cmnd * scp)
1058 * eh_strategy_handler - driver supplied alternate to scsi_unjam_host()
1059 * @shp: host on which error has occurred
1061 * Returns TRUE if host unjammed, else FALSE.
1065 * Calling context: kernel thread
1067 * Notes: Invoked from scsi_eh thread. LLD supplied alternate to
1068 * scsi_unjam_host() found in scsi_error.c
1070 * Optionally defined in: LLD
1072 int eh_strategy_handler(struct Scsi_Host * shp)
1076 * info - supply information about given host: driver name plus data
1077 * to distinguish given host
1078 * @shp: host to supply information about
1080 * Return ASCII null terminated string. [This driver is assumed to
1081 * manage the memory pointed to and maintain it, typically for the
1082 * lifetime of this host.]
1086 * Calling context: process
1088 * Notes: Often supplies PCI or ISA information such as IO addresses
1089 * and interrupt numbers. If not supplied struct Scsi_Host::name used
1090 * instead. It is assumed the returned information fits on one line
1091 * (i.e. does not included embedded newlines).
1092 * The SCSI_IOCTL_PROBE_HOST ioctl yields the string returned by this
1093 * function (or struct Scsi_Host::name if this function is not
1095 * In a similar manner, init_this_scsi_driver() outputs to the console
1096 * each host's "info" (or name) for the driver it is registering.
1097 * Also if proc_info() is not supplied, the output of this function
1100 * Optionally defined in: LLD
1102 const char * info(struct Scsi_Host * shp)
1106 * ioctl - driver can respond to ioctls
1107 * @sdp: device that ioctl was issued for
1108 * @cmd: ioctl number
1109 * @arg: pointer to read or write data from. Since it points to
1110 * user space, should use appropriate kernel functions
1111 * (e.g. copy_from_user() ). In the Unix style this argument
1112 * can also be viewed as an unsigned long.
1114 * Returns negative "errno" value when there is a problem. 0 or a
1115 * positive value indicates success and is returned to the user space.
1119 * Calling context: process
1121 * Notes: The SCSI subsystem uses a "trickle down" ioctl model.
1122 * The user issues an ioctl() against an upper level driver
1123 * (e.g. /dev/sdc) and if the upper level driver doesn't recognize
1124 * the 'cmd' then it is passed to the SCSI mid level. If the SCSI
1125 * mid level does not recognize it, then the LLD that controls
1126 * the device receives the ioctl. According to recent Unix standards
1127 * unsupported ioctl() 'cmd' numbers should return -ENOTTY.
1129 * Optionally defined in: LLD
1131 int ioctl(struct scsi_device *sdp, int cmd, void *arg)
1135 * proc_info - supports /proc/scsi/{driver_name}/{host_no}
1136 * @buffer: anchor point to output to (0==writeto1_read0) or fetch from
1137 * (1==writeto1_read0).
1138 * @start: where "interesting" data is written to. Ignored when
1139 * 1==writeto1_read0.
1140 * @offset: offset within buffer 0==writeto1_read0 is actually
1141 * interested in. Ignored when 1==writeto1_read0 .
1142 * @length: maximum (or actual) extent of buffer
1143 * @host_no: host number of interest (struct Scsi_Host::host_no)
1144 * @writeto1_read0: 1 -> data coming from user space towards driver
1145 * (e.g. "echo some_string > /proc/scsi/xyz/2")
1146 * 0 -> user what data from this driver
1147 * (e.g. "cat /proc/scsi/xyz/2")
1149 * Returns length when 1==writeto1_read0. Otherwise number of chars
1150 * output to buffer past offset.
1154 * Calling context: process
1156 * Notes: Driven from scsi_proc.c which interfaces to proc_fs. proc_fs
1157 * support can now be configured out of the scsi subsystem.
1159 * Optionally defined in: LLD
1161 int proc_info(char * buffer, char ** start, off_t offset,
1162 int length, int host_no, int writeto1_read0)
1166 * queuecommand - queue scsi command, invoke 'done' on completion
1167 * @scp: pointer to scsi command object
1168 * @done: function pointer to be invoked on completion
1170 * Returns 0 on success.
1172 * If there's a failure, return either:
1174 * SCSI_MLQUEUE_DEVICE_BUSY if the device queue is full, or
1175 * SCSI_MLQUEUE_HOST_BUSY if the entire host queue is full
1177 * On both of these returns, the mid-layer will requeue the I/O
1179 * - if the return is SCSI_MLQUEUE_DEVICE_BUSY, only that particular
1180 * device will be paused, and it will be unpaused when a command to
1181 * the device returns (or after a brief delay if there are no more
1182 * outstanding commands to it). Commands to other devices continue
1183 * to be processed normally.
1185 * - if the return is SCSI_MLQUEUE_HOST_BUSY, all I/O to the host
1186 * is paused and will be unpaused when any command returns from
1187 * the host (or after a brief delay if there are no outstanding
1188 * commands to the host).
1190 * For compatibility with earlier versions of queuecommand, any
1191 * other return value is treated the same as
1192 * SCSI_MLQUEUE_HOST_BUSY.
1194 * Other types of errors that are detected immediately may be
1195 * flagged by setting scp->result to an appropriate value,
1196 * invoking the 'done' callback, and then returning 0 from this
1197 * function. If the command is not performed immediately (and the
1198 * LLD is starting (or will start) the given command) then this
1199 * function should place 0 in scp->result and return 0.
1201 * Command ownership. If the driver returns zero, it owns the
1202 * command and must take responsibility for ensuring the 'done'
1203 * callback is executed. Note: the driver may call done before
1204 * returning zero, but after it has called done, it may not
1205 * return any value other than zero. If the driver makes a
1206 * non-zero return, it must not execute the command's done
1207 * callback at any time.
1209 * Locks: struct Scsi_Host::host_lock held on entry (with "irqsave")
1210 * and is expected to be held on return.
1212 * Calling context: in interrupt (soft irq) or process context
1214 * Notes: This function should be relatively fast. Normally it will
1215 * not wait for IO to complete. Hence the 'done' callback is invoked
1216 * (often directly from an interrupt service routine) some time after
1217 * this function has returned. In some cases (e.g. pseudo adapter
1218 * drivers that manufacture the response to a SCSI INQUIRY)
1219 * the 'done' callback may be invoked before this function returns.
1220 * If the 'done' callback is not invoked within a certain period
1221 * the SCSI mid level will commence error processing.
1222 * If a status of CHECK CONDITION is placed in "result" when the
1223 * 'done' callback is invoked, then the LLD driver should
1224 * perform autosense and fill in the struct scsi_cmnd::sense_buffer
1225 * array. The scsi_cmnd::sense_buffer array is zeroed prior to
1226 * the mid level queuing a command to an LLD.
1230 int queuecommand(struct scsi_cmnd * scp,
1231 void (*done)(struct scsi_cmnd *))
1235 * release - release all resources associated with given host
1236 * @shp: host to be released.
1238 * Return value ignored (could soon be a function returning void).
1242 * Calling context: process
1244 * Notes: Invoked from scsi_module.c's exit_this_scsi_driver().
1245 * LLD's implementation of this function should call
1246 * scsi_unregister(shp) prior to returning.
1247 * Only needed for old-style host templates.
1249 * Defined in: LLD (required in "passive initialization model",
1250 * should not be defined in hotplug model)
1252 int release(struct Scsi_Host * shp)
1256 * slave_alloc - prior to any commands being sent to a new device
1257 * (i.e. just prior to scan) this call is made
1258 * @sdp: pointer to new device (about to be scanned)
1260 * Returns 0 if ok. Any other return is assumed to be an error and
1261 * the device is ignored.
1265 * Calling context: process
1267 * Notes: Allows the driver to allocate any resources for a device
1268 * prior to its initial scan. The corresponding scsi device may not
1269 * exist but the mid level is just about to scan for it (i.e. send
1270 * and INQUIRY command plus ...). If a device is found then
1271 * slave_configure() will be called while if a device is not found
1272 * slave_destroy() is called.
1273 * For more details see the include/scsi/scsi_host.h file.
1275 * Optionally defined in: LLD
1277 int slave_alloc(struct scsi_device *sdp)
1281 * slave_configure - driver fine tuning for given device just after it
1282 * has been first scanned (i.e. it responded to an
1284 * @sdp: device that has just been attached
1286 * Returns 0 if ok. Any other return is assumed to be an error and
1287 * the device is taken offline. [offline devices will _not_ have
1288 * slave_destroy() called on them so clean up resources.]
1292 * Calling context: process
1294 * Notes: Allows the driver to inspect the response to the initial
1295 * INQUIRY done by the scanning code and take appropriate action.
1296 * For more details see the include/scsi/scsi_host.h file.
1298 * Optionally defined in: LLD
1300 int slave_configure(struct scsi_device *sdp)
1304 * slave_destroy - given device is about to be shut down. All
1305 * activity has ceased on this device.
1306 * @sdp: device that is about to be shut down
1312 * Calling context: process
1314 * Notes: Mid level structures for given device are still in place
1315 * but are about to be torn down. Any per device resources allocated
1316 * by this driver for given device should be freed now. No further
1317 * commands will be sent for this sdp instance. [However the device
1318 * could be re-attached in the future in which case a new instance
1319 * of struct scsi_device would be supplied by future slave_alloc()
1320 * and slave_configure() calls.]
1322 * Optionally defined in: LLD
1324 void slave_destroy(struct scsi_device *sdp)
1330 struct scsi_host_template
1331 -------------------------
1332 There is one "struct scsi_host_template" instance per LLD ***. It is
1333 typically initialized as a file scope static in a driver's header file. That
1334 way members that are not explicitly initialized will be set to 0 or NULL.
1336 name - name of driver (may contain spaces, please limit to
1337 less than 80 characters)
1338 proc_name - name used in "/proc/scsi/<proc_name>/<host_no>" and
1339 by sysfs in one of its "drivers" directories. Hence
1340 "proc_name" should only contain characters acceptable
1341 to a Unix file name.
1342 (*queuecommand)() - primary callback that the mid level uses to inject
1343 SCSI commands into an LLD.
1344 The structure is defined and commented in include/scsi/scsi_host.h
1346 *** In extreme situations a single driver may have several instances
1347 if it controls several different classes of hardware (e.g. an LLD
1348 that handles both ISA and PCI cards and has a separate instance of
1349 struct scsi_host_template for each class).
1353 There is one struct Scsi_Host instance per host (HBA) that an LLD
1354 controls. The struct Scsi_Host structure has many members in common
1355 with "struct scsi_host_template". When a new struct Scsi_Host instance
1356 is created (in scsi_host_alloc() in hosts.c) those common members are
1357 initialized from the driver's struct scsi_host_template instance. Members
1359 host_no - system wide unique number that is used for identifying
1360 this host. Issued in ascending order from 0.
1361 can_queue - must be greater than 0; do not send more than can_queue
1362 commands to the adapter.
1363 this_id - scsi id of host (scsi initiator) or -1 if not known
1364 sg_tablesize - maximum scatter gather elements allowed by host.
1365 0 implies scatter gather not supported by host
1366 max_sectors - maximum number of sectors (usually 512 bytes) allowed
1367 in a single SCSI command. The default value of 0 leads
1368 to a setting of SCSI_DEFAULT_MAX_SECTORS (defined in
1369 scsi_host.h) which is currently set to 1024. So for a
1370 disk the maximum transfer size is 512 KB when max_sectors
1371 is not defined. Note that this size may not be sufficient
1372 for disk firmware uploads.
1373 cmd_per_lun - maximum number of commands that can be queued on devices
1374 controlled by the host. Overridden by LLD calls to
1375 scsi_adjust_queue_depth().
1376 unchecked_isa_dma - 1=>only use bottom 16 MB of ram (ISA DMA addressing
1377 restriction), 0=>can use full 32 bit (or better) DMA
1379 use_clustering - 1=>SCSI commands in mid level's queue can be merged,
1380 0=>disallow SCSI command merging
1381 hostt - pointer to driver's struct scsi_host_template from which
1382 this struct Scsi_Host instance was spawned
1383 hostt->proc_name - name of LLD. This is the driver name that sysfs uses
1384 transportt - pointer to driver's struct scsi_transport_template instance
1385 (if any). FC and SPI transports currently supported.
1386 sh_list - a double linked list of pointers to all struct Scsi_Host
1387 instances (currently ordered by ascending host_no)
1388 my_devices - a double linked list of pointers to struct scsi_device
1389 instances that belong to this host.
1390 hostdata[0] - area reserved for LLD at end of struct Scsi_Host. Size
1391 is set by the second argument (named 'xtr_bytes') to
1392 scsi_host_alloc() or scsi_register().
1394 The scsi_host structure is defined in include/scsi/scsi_host.h
1398 Generally, there is one instance of this structure for each SCSI logical unit
1399 on a host. Scsi devices connected to a host are uniquely identified by a
1400 channel number, target id and logical unit number (lun).
1401 The structure is defined in include/scsi/scsi_device.h
1405 Instances of this structure convey SCSI commands to the LLD and responses
1406 back to the mid level. The SCSI mid level will ensure that no more SCSI
1407 commands become queued against the LLD than are indicated by
1408 scsi_adjust_queue_depth() (or struct Scsi_Host::cmd_per_lun). There will
1409 be at least one instance of struct scsi_cmnd available for each SCSI device.
1410 Members of interest:
1411 cmnd - array containing SCSI command
1412 cmnd_len - length (in bytes) of SCSI command
1413 sc_data_direction - direction of data transfer in data phase. See
1414 "enum dma_data_direction" in include/linux/dma-mapping.h
1415 request_bufflen - number of data bytes to transfer (0 if no data phase)
1416 use_sg - ==0 -> no scatter gather list, hence transfer data
1417 to/from request_buffer
1418 - >0 -> scatter gather list (actually an array) in
1419 request_buffer with use_sg elements
1420 request_buffer - either contains data buffer or scatter gather list
1421 depending on the setting of use_sg. Scatter gather
1422 elements are defined by 'struct scatterlist' found
1423 in include/asm/scatterlist.h .
1424 done - function pointer that should be invoked by LLD when the
1425 SCSI command is completed (successfully or otherwise).
1426 Should only be called by an LLD if the LLD has accepted
1427 the command (i.e. queuecommand() returned or will return
1428 0). The LLD may invoke 'done' prior to queuecommand()
1430 result - should be set by LLD prior to calling 'done'. A value
1431 of 0 implies a successfully completed command (and all
1432 data (if any) has been transferred to or from the SCSI
1433 target device). 'result' is a 32 bit unsigned integer that
1434 can be viewed as 4 related bytes. The SCSI status value is
1435 in the LSB. See include/scsi/scsi.h status_byte(),
1436 msg_byte(), host_byte() and driver_byte() macros and
1438 sense_buffer - an array (maximum size: SCSI_SENSE_BUFFERSIZE bytes) that
1439 should be written when the SCSI status (LSB of 'result')
1440 is set to CHECK_CONDITION (2). When CHECK_CONDITION is
1441 set, if the top nibble of sense_buffer[0] has the value 7
1442 then the mid level will assume the sense_buffer array
1443 contains a valid SCSI sense buffer; otherwise the mid
1444 level will issue a REQUEST_SENSE SCSI command to
1445 retrieve the sense buffer. The latter strategy is error
1446 prone in the presence of command queuing so the LLD should
1447 always "auto-sense".
1448 device - pointer to scsi_device object that this command is
1450 resid - an LLD should set this signed integer to the requested
1451 transfer length (i.e. 'request_bufflen') less the number
1452 of bytes that are actually transferred. 'resid' is
1453 preset to 0 so an LLD can ignore it if it cannot detect
1454 underruns (overruns should be rare). If possible an LLD
1455 should set 'resid' prior to invoking 'done'. The most
1456 interesting case is data transfers from a SCSI target
1457 device device (i.e. READs) that underrun.
1458 underflow - LLD should place (DID_ERROR << 16) in 'result' if
1459 actual number of bytes transferred is less than this
1460 figure. Not many LLDs implement this check and some that
1461 do just output an error message to the log rather than
1462 report a DID_ERROR. Better for an LLD to implement
1465 The scsi_cmnd structure is defined in include/scsi/scsi_cmnd.h
1470 Each struct Scsi_Host instance has a spin_lock called struct
1471 Scsi_Host::default_lock which is initialized in scsi_host_alloc() [found in
1472 hosts.c]. Within the same function the struct Scsi_Host::host_lock pointer
1473 is initialized to point at default_lock with the scsi_assign_lock() function.
1474 Thereafter lock and unlock operations performed by the mid level use the
1475 struct Scsi_Host::host_lock pointer.
1477 LLDs can override the use of struct Scsi_Host::default_lock by
1478 using scsi_assign_lock(). The earliest opportunity to do this would
1479 be in the detect() function after it has invoked scsi_register(). It
1480 could be replaced by a coarser grain lock (e.g. per driver) or a
1481 lock of equal granularity (i.e. per host). Using finer grain locks
1482 (e.g. per SCSI device) may be possible by juggling locks in
1487 Autosense (or auto-sense) is defined in the SAM-2 document as "the
1488 automatic return of sense data to the application client coincident
1489 with the completion of a SCSI command" when a status of CHECK CONDITION
1490 occurs. LLDs should perform autosense. This should be done when the LLD
1491 detects a CHECK CONDITION status by either:
1492 a) instructing the SCSI protocol (e.g. SCSI Parallel Interface (SPI))
1493 to perform an extra data in phase on such responses
1494 b) or, the LLD issuing a REQUEST SENSE command itself
1496 Either way, when a status of CHECK CONDITION is detected, the mid level
1497 decides whether the LLD has performed autosense by checking struct
1498 scsi_cmnd::sense_buffer[0] . If this byte has an upper nibble of 7 (or 0xf)
1499 then autosense is assumed to have taken place. If it has another value (and
1500 this byte is initialized to 0 before each command) then the mid level will
1501 issue a REQUEST SENSE command.
1503 In the presence of queued commands the "nexus" that maintains sense
1504 buffer data from the command that failed until a following REQUEST SENSE
1505 may get out of synchronization. This is why it is best for the LLD
1506 to perform autosense.
1509 Changes since lk 2.4 series
1510 ===========================
1511 io_request_lock has been replaced by several finer grained locks. The lock
1512 relevant to LLDs is struct Scsi_Host::host_lock and there is
1515 The older error handling mechanism has been removed. This means the
1516 LLD interface functions abort() and reset() have been removed.
1517 The struct scsi_host_template::use_new_eh_code flag has been removed.
1519 In the 2.4 series the SCSI subsystem configuration descriptions were
1520 aggregated with the configuration descriptions from all other Linux
1521 subsystems in the Documentation/Configure.help file. In the 2.6 series,
1522 the SCSI subsystem now has its own (much smaller) drivers/scsi/Kconfig
1523 file that contains both configuration and help information.
1525 struct SHT has been renamed to struct scsi_host_template.
1527 Addition of the "hotplug initialization model" and many extra functions
1533 The following people have contributed to this document:
1534 Mike Anderson <andmike at us dot ibm dot com>
1535 James Bottomley <James dot Bottomley at steeleye dot com>
1536 Patrick Mansfield <patmans at us dot ibm dot com>
1537 Christoph Hellwig <hch at infradead dot org>
1538 Doug Ledford <dledford at redhat dot com>
1539 Andries Brouwer <Andries dot Brouwer at cwi dot nl>
1540 Randy Dunlap <rddunlap at osdl dot org>
1541 Alan Stern <stern at rowland dot harvard dot edu>
1545 dgilbert at interlog dot com
projects / mirror_ubuntu-artful-kernel.git / blob