3 - ovs-vswitchd no longer deletes datapath flows on exit by default.
5 * The OpenFlow ofp_desc/serial_num may now be configured by setting the
6 value of other-config:dp-sn in the Bridge table.
7 * Added support to watch CONTROLLER port status in fast failover group.
8 * New action "delete_field".
10 * Deprecated DPDK pdump packet capture support removed.
11 * Deprecated DPDK ring ports (dpdkr) are no longer supported.
12 * Add hardware offload support for VLAN Push/Pop actions (experimental).
13 * Add hardware offload support for matching IPv6 protocol (experimental).
14 * Add hardware offload support for set of IPv6 src/dst/ttl
15 and tunnel push-output actions (experimental).
16 * OVS validated with DPDK 19.11.2, due to the inclusion of fixes for
17 CVE-2020-10722, CVE-2020-10723, CVE-2020-10724, CVE-2020-10725 and
18 CVE-2020-10726, this DPDK version is strongly recommended to be used.
20 * Support for kernel versions up to 5.5.x.
22 * New netdev class 'afxdp-nonpmd' for netdev-afxdp to save CPU cycles
23 by enabling interrupt mode.
25 * Removed artificial datapath flow limit that was 65536.
26 Now number of datapath flows is fully controlled by revalidators and the
27 'other_config:flow-limit' knob.
28 * Add support for conntrack zone-based timeout policy.
29 * New configuration knob 'other_config:lb-output-action' for bond ports
30 that enables new datapath action 'lb_output' to avoid recirculation
31 in balance-tcp mode. Disabled by default.
32 * Add runtime CPU ISA detection to allow optimized ISA functions
33 * Add support for dynamically changing DPCLS subtable lookup functions
34 * Add ISA optimized DPCLS lookup function using AVX512
35 - Tunnels: TC Flower offload
36 * Tunnel Local endpoint address masked match are supported.
37 * Tunnel Romte endpoint address masked match are supported.
43 * OVN has been removed from this repository. It now exists as a
44 separate project. You can find it at
45 https://github.com/ovn-org/ovn.git
47 * Add option to enable, disable and query TCP sequence checking in
49 * Add support for conntrack zone limits.
50 * Command "ovs-appctl dpctl/dump-flows" refactored to show subtable
51 miniflow bits for userspace datapath.
53 * New option 'use-need-wakeup' for netdev-afxdp to control enabling
54 of corresponding 'need_wakeup' flag in AF_XDP rings. Enabled by default
55 if supported by libbpf.
56 * 'xdpmode' option for netdev-afxdp renamed to 'xdp-mode'.
57 Modes also updated. New values:
58 native-with-zerocopy - former DRV
59 native - new one, DRV without zero-copy
61 best-effort [default] - new one, chooses the best available from
64 * DPDK pdump packet capture support disabled by default. New configure
65 option '--enable-dpdk-pdump' to enable it.
66 * DPDK pdump support is deprecated and will be removed in next releases.
67 * DPDK ring ports (dpdkr) are deprecated and will be removed in next
69 * Add support for DPDK 19.11.
70 * Add hardware offload support for output, drop, set of MAC, IPv4 and
71 TCP/UDP ports actions (experimental).
72 * Add experimental support for TSO.
74 * The rstp_statistics column in Port table will only be updated every
75 stats-update-interval configured in Open_vSwitch table.
77 * When ovsdb-server is running in backup mode, the default value of probe
78 interval is increased to 60 seconds for the connection to the
79 replication server. This value is configurable with the unixctl
80 command - ovsdb-server/set-active-ovsdb-server-probe-interval.
81 * ovsdb-server: New OVSDB extension to allow clients to specify row UUIDs.
82 - 'ovs-appctl dpctl/dump-flows' can now show offloaded=partial for
83 partially offloaded flows, dp:dpdk for fully offloaded by dpdk, and
84 type filter supports new filters: "dpdk" and "partially-offloaded".
85 - GTP-U Tunnel Protocol
86 * Add two new fields: tun_gtpu_flags, tun_gtpu_msgtype.
87 * Only support for userspace datapath.
92 * New option 'other_config:dpdk-socket-limit' to limit amount of
93 hugepage memory that can be used by DPDK.
94 * Add support for vHost Post-copy Live Migration (experimental).
95 * OVS validated with DPDK 18.11.2 which is the new minimal supported
97 * DPDK 18.11.1 and lower is no longer supported.
98 * New option 'tx-retries-max' to set the maximum amount of vhost tx
99 retries that can be made.
101 * All features required by OpenFlow 1.5 are now implemented, so
102 ovs-vswitchd now enables OpenFlow 1.5 by default (in addition to
103 OpenFlow 1.0 to 1.4).
104 * Removed support for OpenFlow 1.6 (draft), which ONF abandoned.
105 * New action "check_pkt_larger".
106 * Support for OpenFlow 1.5 "meter" action.
107 - Userspace datapath:
108 * ICMPv6 ND enhancements: support for match and set ND options type
110 * Add v4/v6 fragmentation support for conntrack.
111 * New ovs-appctl "dpctl/ipf-set-enabled" and "dpctl/ipf-set-disabled"
112 commands for userspace datapath conntrack fragmentation support.
113 * New "ovs-appctl dpctl/ipf-set-min-frag" command for userspace
114 datapath conntrack fragmentation support.
115 * New "ovs-appctl dpctl/ipf-set-max-nfrags" command for userspace datapath
116 conntrack fragmentation support.
117 * New "ovs-appctl dpctl/ipf-get-status" command for userspace datapath
118 conntrack fragmentation support.
119 * New action "check_pkt_len".
120 * Port configuration with "other-config:priority-tags" now has a mode
121 that retains the 802.1Q header even if VLAN and priority are both zero.
122 * 'ovs-appctl exit' now implies cleanup of non-internal ports in userspace
123 datapath regardless of '--cleanup' option. Use '--cleanup' to remove
125 * Removed experimental tag for SMC cache.
126 * Datapath classifer code refactored to enable function pointers to select
127 the lookup implementation at runtime. This enables specialization of
128 specific subtables based on the miniflow attributes, enhancing the
129 performance of the subtable search.
130 * Add Linux AF_XDP support through a new experimental netdev type "afxdp".
132 * OVSDB clients can now resynchronize with clustered servers much more
133 quickly after a brief disconnection, saving bandwidth and CPU time.
134 See section 4.1.15 of ovsdb-server(7) for details of related OVSDB
136 * Support to convert from cluster database to standalone database is now
137 available when clustered is down and cannot be revived using ovsdb-tool
138 . Check "Database Migration Commands" in ovsdb-tool man section.
141 - select IPAM mac_prefix in a random manner if not provided by the user
142 - add the capability to specify a static IPv4 and/or IPv6 address and
143 get the L2 one allocated dynamically using the following syntax:
144 ovn-nbctl lsp-set-addresses <port> "dynamic <IPv4 addr> <IPv6 addr>"
145 * Added the HA chassis group support.
146 * Added 'external' logical port support.
147 * Added Policy-based routing(PBR) support to create permit/deny/reroute
148 policies on the logical router. New table(Logical_Router_Policy) added in
149 OVN-NB schema. New "ovn-nbctl" commands to add/delete/list PBR policies.
150 * Support for Transport Zones, a way to separate chassis into
151 logical groups which results in tunnels only been formed between
152 members of the same transport zone(s).
153 * Support for IGMP Snooping and IGMP Querier.
154 - New QoS type "linux-netem" on Linux.
155 - Added support for TLS Server Name Indication (SNI).
157 * Support for the kernel versions 4.19.x and 4.20.x.
158 * Support for the kernel version 5.0.x.
159 * Add support for conntrack zone-based timeout policy.
160 - 'ovs-dpctl dump-flows' is no longer suitable for dumping offloaded flows.
161 'ovs-appctl dpctl/dump-flows' should be used instead.
162 - Add new argument '--offload-stats' for command
163 'ovs-appctl bridge/dump-flows',
164 so it can display offloaded packets statistics.
165 - Add L2 GRE tunnel over IPv6 support.
167 v2.11.0 - 19 Feb 2019
168 ---------------------
170 * OFPMP_TABLE_FEATURES_REQUEST can now modify table features.
172 * "mod-table" command can now change OpenFlow table names.
174 * OVN-SB schema changed: duplicated IP with same Encapsulation type
175 is not allowed any more. Please refer to
176 Documentation/intro/install/ovn-upgrades.rst for the instructions
177 in case there are problems encountered when upgrading from an earlier
179 * New support for IPSEC encrypted tunnels between hypervisors.
180 * ovn-ctl: allow passing user:group ids to the OVN daemons.
182 - add the capability to dynamically assign just L2 addresses
183 - add the capability to specify a static ip address and get the L2 one
184 allocated dynamically using the following syntax:
185 ovn-nbctl lsp-set-addresses <port> "dynamic <IP>"
187 * Add support for DPDK 18.11
188 * Add support for port representors.
189 - Userspace datapath:
190 * Add option for simple round-robin based Rxq to PMD assignment.
191 It can be set with pmd-rxq-assign.
192 * Add support for Auto load balancing of PMDs (experimental)
193 * Added new per-port configurable option to manage EMC:
194 'other_config:emc-enable'.
195 - Add 'symmetric_l3' hash function.
196 - OVS now honors 'updelay' and 'downdelay' for bonds with LACP configured.
198 * New configuration option "offload-rebalance", that enables dynamic
199 rebalancing of offloaded flows.
200 - The environment variable OVS_SYSLOG_METHOD, if set, is now used
201 as the default syslog method.
202 - The environment variable OVS_CTL_TIMEOUT, if set, is now used
203 as the default timeout for control utilities.
204 - The environment variable OVS_RESOLV_CONF, if set, is now used
205 as the DNS server configuration file.
207 * OVN packages are split from OVS packages. A new spec
208 file - ovn-fedora.spec.in is added to generate OVN packages.
210 * Support for the kernel versions 4.16.x, 4.17.x, and 4.18.x.
212 v2.10.0 - 18 Aug 2018
213 ---------------------
214 - ovs-vswitchd and utilities now support DNS names in OpenFlow and
217 * New options --l7 and --l7-len to "ofproto/trace" command.
218 * Previous versions gave OpenFlow tables default names of the form
219 "table#". These are not helpful names for the purpose of accepting
220 and displaying table names, so now tables by default have no names.
221 * The "null" interface type, deprecated since 2013, has been removed.
222 * Add minimum network namespace support for Linux.
223 * New command "lacp/show-stats"
225 * ovs-ofctl now accepts and display table names in place of numbers. By
226 default it always accepts names and in interactive use it displays them;
227 use --names or --no-names to override. See ovs-ofctl(8) for details.
228 - ovs-vsctl: New commands "add-bond-iface" and "del-bond-iface".
230 * New commands "ct-set-limits", "ct-del-limits", and "ct-get-limits".
232 * OFPT_ROLE_STATUS is now available in OpenFlow 1.3.
233 * OpenFlow 1.5 extensible statistics (OXS) now implemented.
234 * New OpenFlow 1.0 extensions for group support.
235 * Default selection method for select groups is now dp_hash with improved
238 * Add support for compiling OVS with the latest Linux 4.14 kernel.
239 * Added support for meters.
240 * Add support for conntrack zone limit.
242 * Implemented icmp4/icmp6/tcp_reset actions in order to drop the packet
243 and reply with a RST for TCP or ICMPv4/ICMPv6 unreachable message for
244 other IPv4/IPv6-based protocols whenever a reject ACL rule is hit.
245 * ACL match conditions can now match on Port_Groups as well as address
246 sets that are automatically generated by Port_Groups. ACLs can be
247 applied directly to Port_Groups as well.
248 * ovn-nbctl can now run as a daemon (long-lived, background process).
249 See ovn-nbctl(8) for details.
251 * New 'check-dpdk' Makefile target to run a new system testsuite.
252 See Testing topic for the details.
253 * Add LSC interrupt support for DPDK physical devices.
254 * Allow init to fail and record DPDK status/version in OVS database.
255 * Add experimental flow hardware offload support
256 * Support both shared and per port mempools for DPDK devices.
257 - Userspace datapath:
258 * Commands ovs-appctl dpif-netdev/pmd-*-show can now work on a single PMD
259 * Detailed PMD performance metrics available with new command
260 ovs-appctl dpif-netdev/pmd-perf-show
261 * Supervision of PMD performance metrics and logging of suspicious
263 * Add signature match cache (SMC) as experimental feature. When turned on,
264 it improves throughput when traffic has many more flows than EMC size.
266 * Implemented ERSPAN protocol (draft-foschiano-erspan-00.txt) for
267 both kernel datapath and userspace datapath.
268 * Added port-based and flow-based ERSPAN tunnel port support, added
269 OpenFlow rules matching ERSPAN fields. See ovs-fields(7).
271 * ovs-pki now generates x.509 version 3 certificate. The new format adds
272 subjectAltName field and sets its value the same as common name (CN).
276 - NSH implementation now conforms to latest draft (draft-ietf-sfc-nsh-28).
278 * Add a new action dec_nsh_ttl.
279 * Enable NSH support in kernel datapath.
280 - OVSDB has new, experimental support for database clustering:
281 * New high-level documentation in ovsdb(7).
282 * New file format documentation for developers in ovsdb(5).
283 * Protocol documentation moved from ovsdb-server(1) to ovsdb-server(7).
284 * ovsdb-server now supports online schema conversion via
285 "ovsdb-client convert".
286 * ovsdb-server now always hosts a built-in database named _Server. See
287 ovsdb-server(5) for more details.
288 * ovsdb-client: New "get-schema-cksum", "query", "backup", "restore",
289 and "wait" commands. New --timeout option.
290 * ovsdb-tool: New "create-cluster", "join-cluster", "db-cid", "db-sid",
291 "db-local-address", "db-is-clustered", "db-is-standalone", "db-name",
292 "schema-name", "compare-versions", and "check-cluster" commands.
293 * ovsdb-server: New ovs-appctl commands for managing clusters.
294 * ovs-sandbox: New support for clustered databases.
295 - ovs-vsctl and other commands that display data in tables now support a
296 --max-column-width option to limit column width.
297 - No longer slow-path traffic that sends to a controller. Applications,
298 such as OVN ACL logging, want to send a copy of a packet to a
299 controller while leaving the actual packet forwarding in the datapath.
301 * The "requested-chassis" option for a logical switch port now accepts a
302 chassis "hostname" in addition to a chassis "name".
304 - Added support to send IPv6 Router Advertisement packets in response to
305 the IPv6 Router Solicitation packets from the VIF ports.
306 - Added support to generate Neighbor Solicitation packets using the OVN
307 action 'nd_ns' to resolve unknown next hop MAC addresses for the
309 * Add support for QoS bandwidth limit with DPDK.
310 * ovn-ctl: New commands run_nb_ovsdb and run_sb_ovsdb.
311 * ovn-sbctl, ovn-nbctl: New options --leader-only, --no-leader-only.
313 * ct_clear action is now backed by kernel datapath. Support is probed for
316 * Add support for compiling OVS with the latest Linux 4.13 kernel
317 - ovs-dpctl and related ovs-appctl commands:
318 * "flush-conntrack" now accept a 5-tuple to delete a specific
319 connection tracking entry.
320 * New "ct-set-maxconns", "ct-get-maxconns", and "ct-get-nconns" commands
321 for userspace datapath.
322 - No longer send packets to the Linux TAP device if it's DOWN unless it is
323 in another networking namespace.
325 * Add support for DPDK v17.11
326 * Add support for vHost IOMMU
327 * New debug appctl command 'netdev-dpdk/get-mempool-info'.
328 * All the netdev-dpdk appctl commands described in ovs-vswitchd man page.
330 - DPDK physical ports now return custom set of "dropped", "error" and
331 "management" statistics.
332 - ovs-ofctl dump-ports command now prints new of set custom statistics
333 if available (for OpenFlow 1.4+).
334 * Switch from round-robin allocation of rxq to pmd assignments to a
335 utilization-based allocation.
336 * New appctl command 'dpif-netdev/pmd-rxq-rebalance' to rebalance rxq to
338 * Add rxq utilization of pmd to appctl 'dpif-netdev/pmd-rxq-show'.
339 * Add support for vHost dequeue zero copy (experimental).
340 - Userspace datapath:
341 * Output packet batching support.
343 * Datapath IDs may now be specified as 0x1 (etc.) instead of 16 digits.
344 * Configuring a controller, or unconfiguring all controllers, now deletes
345 all groups and meters (as well as all flows).
346 - New --enable-sparse configure option enables "sparse" checking by default.
347 - Added additional information to vhost-user status.
352 * ovs-ofctl can now accept and display port names in place of numbers. By
353 default it always accepts names and in interactive use it displays them;
354 use --names or --no-names to override. See ovs-ofctl(8) for details.
355 * "ovs-ofctl dump-flows" now accepts --no-stats to omit flow statistics.
356 - New ovs-dpctl command "ct-stats-show" to show connection tracking stats.
358 * Added support to set packet mark for tunnel endpoint using
359 `egress_pkt_mark` OVSDB option.
360 * When using Linux kernel datapath tunnels may be created using rtnetlink.
361 This will allow us to take advantage of new tunnel features without
362 having to make changes to the vport modules.
363 - EMC insertion probability is reduced to 1% and is configurable via
364 the new 'other_config:emc-insert-inv-prob' option.
366 * DPDK log messages redirected to OVS logging subsystem.
367 Log level can be changed in a usual OVS way using
368 'ovs-appctl vlog' commands for 'dpdk' module. Lower bound
369 still can be configured via extra arguments for DPDK EAL.
370 * dpdkvhostuser ports are marked as deprecated. They will be removed
371 in an upcoming release.
372 * Support for DPDK v17.05.1.
373 - IPFIX now provides additional counters:
374 * Total counters since metering process startup.
375 * Per-flow TCP flag counters.
376 * Multicast, broadcast, and unicast counters.
377 - New support for multiple VLANs (802.1ad or "QinQ"), including a new
378 "dot1q-tunnel" port VLAN mode.
379 - In ovn-vsctl and vtep-ctl, record UUIDs in commands may now be
380 abbreviated to 4 hex digits.
381 - Userspace Datapath:
382 * Added NAT support for userspace datapath.
383 * Added FTP and TFTP support with NAT for userspace datapath.
384 * Experimental NSH (Network Service Header) support in userspace datapath.
386 * New built-in DNS support.
387 * IPAM for IPv4 can now exclude user-defined addresses from assignment.
388 * IPAM can now assign IPv6 addresses.
389 * Make the DHCPv4 router setting optional.
390 * Gratuitous ARP for NAT addresses on a distributed logical router.
391 * Allow ovn-controller SSL configuration to be obtained from vswitchd
393 * ovn-trace now has basic support for tracing distributed firewalls.
394 * In ovn-nbctl and ovn-sbctl, record UUIDs in commands may now be
395 abbreviated to 4 hex digits.
396 * "ovn-sbctl lflow-list" can now print OpenFlow flows that correspond
398 * Now uses OVSDB RBAC support to reduce impact of compromised hypervisors.
399 * Multiple chassis may now be specified for L3 gateways. When more than
400 one chassis is specified, OVN will manage high availability for that
402 * Add support for ACL logging.
403 * ovn-northd now has native support for active-standby high availability.
404 - Tracing with ofproto/trace now traces through recirculation.
406 * New support for role-based access control (see ovsdb-server(1)).
407 - New commands 'stp/show' and 'rstp/show' (see ovs-vswitchd(8)).
409 * All features required by OpenFlow 1.4 are now implemented, so
410 ovs-vswitchd now enables OpenFlow 1.4 by default (in addition to
411 OpenFlow 1.0 to 1.3).
412 * Increased support for OpenFlow 1.6 (draft).
413 * Bundles now support hashing by just nw_src or nw_dst.
414 * The "learn" action now supports a "limit" option (see ovs-ofctl(8)).
415 * The port status bit OFPPS_LIVE now reflects link aliveness.
416 * OpenFlow 1.5 packet-out is now supported.
417 * Support for OpenFlow 1.5 field packet_type and packet-type-aware
419 * Added generic encap and decap actions (EXT-382).
420 First supported use case is encap/decap for Ethernet.
421 * Added NSH (Network Service Header) support in userspace
422 Used generic encap and decap actions to implement encapsulation and
423 decapsulation of NSH header.
424 IETF NSH draft - https://datatracker.ietf.org/doc/draft-ietf-sfc-nsh/
425 * Conntrack state is only available to the processing path that
426 follows the "recirc_table" argument of the ct() action. Starting
427 in OVS 2.8, this state is now cleared for the current processing
428 path whenever ct() is called.
430 * OVN services are no longer restarted automatically after upgrade.
431 * ovs-vswitchd and ovsdb-server run as non-root users by default.
432 - Add --cleanup option to command 'ovs-appctl exit' (see ovs-vswitchd(8)).
434 * Use new tunnel port option "packet_type" to configure L2 vs. L3.
435 * In conjunction with PTAP tunnel ports can handle a mix of L2 and L3
437 * New vxlan tunnel extension "gpe" to support VXLAN-GPE tunnels.
438 * New support for non-Ethernet (L3) payloads in GRE and VXLAN-GPE.
439 - The BFD detection multiplier is now user-configurable.
440 - Add experimental support for hardware offloading
441 * HW offloading is disabled by default.
442 * HW offloading is done through the TC interface.
443 - IPv6 link local addresses are now supported on Linux. Use % to designate
447 ---------------------
448 - Utilities and daemons that support SSL now allow protocols and
449 ciphers to be configured with --ssl-protocols and --ssl-ciphers.
451 * QoS is now implemented via egress shaping rather than ingress policing.
452 * DSCP marking is now supported, via the new northbound QoS table.
453 * IPAM now supports fixed MAC addresses.
454 * Support for source IP address based routing.
456 - New --ovs option to also print OpenFlow flows.
457 - put_dhcp_opts and put_dhcp_optsv6 actions may now be traced.
458 * Support for managing SSL and remote connection configuration in
459 northbound and southbound databases.
460 * TCP connections to northbound and southbound databases are no
461 longer enabled by default and must be explicitly configured.
462 See documentation for ovn-sbctl/ovn-nbctl "set-connection"
463 command or the ovn-ctl "--db-sb-create-insecure-remote" and
464 "--db-nb-create-insecure-remote" command-line options for
465 information regarding remote connection configuration.
466 * New appctl "inject-pkt" command in ovn-controller that allows
467 packets to be injected into the connected OVS instance.
468 * Distributed logical routers may now be connected directly to
469 logical switches with localnet ports, by specifying a
470 "redirect-chassis" on the distributed gateway port of the
471 logical router. NAT rules may be specified directly on the
472 distributed logical router, and are handled either centrally on
473 the "redirect-chassis", or in many cases are handled locally on
474 the hypervisor where the corresponding logical port resides.
475 Gratuitous ARP for NAT addresses on a distributed logical
476 router is not yet supported, but will be added in a future
478 - Fixed regression in table stats maintenance introduced in OVS
479 2.3.0, wherein the number of OpenFlow table hits and misses was
482 * OFPT_PACKET_OUT messages are now supported in bundles.
483 * A new "selection_method=dp_hash" type for OpenFlow select group
484 bucket selection that uses the datapath computed 5-tuple hash
485 without making datapath flows match the 5-tuple fields, which
486 is useful for more efficient load balancing, for example. This
487 uses the Netronome extension to OpenFlow 1.5+ that allows
488 control over the OpenFlow select groups selection method. See
489 "selection_method" and related options in ovs-ofctl(8) for
491 * The "sample" action now supports "ingress" and "egress" options.
492 * The "ct" action now supports the TFTP ALG where support is available.
493 * New actions "clone" and "ct_clear".
494 * The "meter" action is now supported in the userspace datapath.
496 * 'bundle' command now supports packet-out messages.
497 * New syntax for 'ovs-ofctl packet-out' command, which uses the
498 same string parser as the 'bundle' command. The old 'packet-out'
499 syntax is deprecated and will be removed in a later OVS
501 * New unixctl "ofctl/packet-out" command, which can be used to
502 instruct a flow monitor to issue OpenFlow packet-out messages.
504 * Remote connections can now be made read-only (see ovsdb-server(1)).
506 * TLV mappings for protocols such as Geneve are now segregated on
507 a per-OpenFlow bridge basis rather than globally. (The interface
509 * Removed support for IPsec tunnels.
511 * New option 'n_rxq_desc' and 'n_txq_desc' fields for DPDK interfaces
512 which set the number of rx and tx descriptors to use for the given port.
513 * Support for DPDK v16.11.
514 * Support for rx checksum offload. Refer DPDK HOWTO for details.
515 * Port Hotplug is now supported.
516 * DPDK physical ports can now have arbitrary names. The PCI address of
517 the device must be set using the 'dpdk-devargs' option. Compatibility
518 with the old dpdk<portid> naming scheme is broken, and as such a
519 device will not be available for use until a valid dpdk-devargs is
521 * Virtual DPDK Poll Mode Driver (vdev PMD) support.
522 * Removed experimental tag.
524 * A package upgrade does not automatically restart OVS service.
525 - ovs-vswitchd/ovs-vsctl:
526 * Ports now have a "protected" flag. Protected ports can not forward
527 frames to other protected ports. Unprotected ports can receive and
528 forward frames to protected and other unprotected ports.
529 - ovs-vsctl, ovn-nbctl, ovn-sbctl, vtep-ctl:
530 * Database commands now accept integer ranges, e.g. "set port
531 eth0 trunks=1-10" to enable trunking VLANs 1 to 10.
534 ---------------------
535 - First supported release of OVN. See ovn-architecture(7) for more
538 * New "monitor_cond" "monitor_cond_update" and "update2" extensions to
541 * OpenFlow 1.3+ bundles now expire after 10 seconds since the
542 last time the bundle was either opened, modified, or closed.
543 * OpenFlow 1.3 Extension 230, adding OpenFlow Bundles support, is
545 * OpenFlow 1.3+ bundles are now supported for group mods as well as
546 flow mods and port mods. Both 'atomic' and 'ordered' bundle
547 flags are supported for group mods as well as flow mods.
548 * Internal OpenFlow rule representation for load and set-field
549 actions is now much more memory efficient. For a complex flow
550 table this can reduce rule memory consumption by 40%.
551 * Bundles are now much more memory efficient than in OVS 2.5.
552 Together with memory efficiency improvements in OpenFlow rule
553 representation, the peak OVS resident memory use during a
554 bundle commit for large complex set of flow mods can be only
555 25% of that in OVS 2.5 (4x lower).
556 * OpenFlow 1.1+ OFPT_QUEUE_GET_CONFIG_REQUEST now supports OFPP_ANY.
557 * OpenFlow 1.4+ OFPMP_QUEUE_DESC is now supported.
558 * OpenFlow 1.4+ OFPT_TABLE_STATUS is now supported.
559 * New property-based packet-in message format NXT_PACKET_IN2 with support
560 for arbitrary user-provided data and for serializing flow table
561 traversal into a continuation for later resumption.
562 * New extension message NXT_SET_ASYNC_CONFIG2 to allow OpenFlow 1.4-like
563 control over asynchronous messages in earlier versions of OpenFlow.
564 * New OpenFlow extension NXM_NX_MPLS_TTL to provide access to MPLS TTL.
565 * New output option, output(port=N,max_len=M), to allow truncating a
566 packet to size M bytes when outputting to port N.
567 * New command OFPGC_ADD_OR_MOD for OFPT_GROUP_MOD message that adds a
568 new group or modifies an existing groups
569 * The optional OpenFlow packet buffering feature is deprecated in
570 this release, and will be removed in the next OVS release
571 (2.7). After the change OVS always sends the 'buffer_id' as
572 0xffffffff in packet-in messages and will send an error
573 response if any other value of this field is included in
574 packet-out and flow mod sent by a controller. Controllers are
575 already expected to work properly in cases where the switch can
576 not buffer packets, so this change should not affect existing
578 * New OpenFlow extension NXT_CT_FLUSH_ZONE to flush conntrack zones.
579 - Improved OpenFlow version compatibility for actions:
580 * New OpenFlow extension to support the "group" action in OpenFlow 1.0.
581 * OpenFlow 1.0 "enqueue" action now properly translated to OpenFlow 1.1+.
582 * OpenFlow 1.1 "mod_nw_ecn" and OpenFlow 1.1+ "mod_nw_ttl" actions now
583 properly translated to OpenFlow 1.0.
585 * queue-get-config command now allows a queue ID to be specified.
586 * '--bundle' option can now be used with OpenFlow 1.3 and with group mods.
587 * New "bundle" command allows executing a mixture of flow and group mods
588 as a single atomic transaction.
589 * New option "--color" to produce colorized output for some commands.
590 * New option '--may-create' to use OFPGC_ADD_OR_MOD in mod-group command.
592 * New "sampling_port" option for "sample" action to allow sampling
593 ingress and egress tunnel metadata with IPFIX.
594 * New ovs-ofctl commands "dump-ipfix-bridge" and "dump-ipfix-flow" to
595 dump bridge IPFIX statistics and flow based IPFIX statistics.
596 * New setting other-config:virtual_obs_id to add an arbitrary string
599 * OVS Linux datapath now implements Conntrack NAT action with all
600 supported Linux kernels.
601 * Support for truncate action.
602 * New QoS type "linux-noop" that prevents Open vSwitch from trying to
603 manage QoS for a given port (useful when other software manages QoS).
605 * New option "n_rxq" for PMD interfaces.
606 Old 'other_config:n-dpdk-rxqs' is no longer supported.
607 Not supported by vHost interfaces. For them number of rx and tx queues
608 is applied from connected virtio device.
609 * New 'other_config:pmd-rxq-affinity' field for PMD interfaces, that
610 allows to pin port's rx queues to desired cores.
611 * New appctl command 'dpif-netdev/pmd-rxq-show' to check the port/rxq
613 * Type of log messages from PMD threads changed from INFO to DBG.
614 * QoS functionality with sample egress-policer implementation.
615 * The mechanism for configuring DPDK has changed to use database
616 * Sensible defaults have been introduced for many of the required
617 configuration options
618 * DB entries have been added for many of the DPDK EAL command line
619 arguments. Additional arguments can be passed via the dpdk-extra
621 * Add ingress policing functionality.
622 * PMD threads servicing vHost User ports can now come from the NUMA
623 node that device memory is located on if CONFIG_RTE_LIBRTE_VHOST_NUMA
625 * Basic connection tracking for the userspace datapath (no ALG,
626 fragmentation or NAT support yet)
627 * Support for DPDK 16.07
628 * Optional support for DPDK pdump enabled.
629 * Jumbo frame support
630 * Remove dpdkvhostcuse port type.
631 * OVS client mode for vHost and vHost reconnect (Requires QEMU 2.7)
632 * 'dpdkvhostuserclient' port type.
633 - Increase number of registers to 16.
634 - ovs-benchmark: This utility has been removed due to lack of use and
637 * New "vlog/close" command.
639 * Added the ability to selectively start the forwarding and database
640 functions (ovs-vswitchd and ovsdb-server, respectively).
642 * Remove max number of sessions limit, to enable connection scaling
645 * Added support for Python 3.4+ in addition to existing support
648 * Introduced SELinux policy package.
649 - Datapath Linux kernel compatibility.
650 * Dropped support for kernel older than 3.10.
651 * Removed VLAN splinters feature.
652 * Datapath supports kernel upto 4.7.
654 * Flow based tunnel match and action can be used for IPv6 address using
655 tun_ipv6_src, tun_ipv6_dst fields.
656 * Added support for IPv6 tunnels, for details checkout FAQ.
657 * Deprecated support for IPsec tunnels ports.
658 - A wrapper script, 'ovs-tcpdump', to easily port-mirror an OVS port and
660 - Introduce --no-self-confinement flag that allows daemons to work with
661 sockets outside their run directory.
662 - ovs-pki: Changed message digest algorithm from SHA-1 to SHA-512 because
663 SHA-1 is no longer secure and some operating systems have started to
664 disable it in OpenSSL.
665 - Add 'mtu_request' column to the Interface table. It can be used to
666 configure the MTU of the ports.
669 - Using openvswitch module in conjunction with upstream Linux tunnels:
670 * When using the openvswitch module distributed with OVS against kernel
671 versions 4.4 to 4.6, the openvswitch module cannot be loaded or used at
672 the same time as "ip_gre".
673 - Conntrack FTP ALGs: When using the openvswitch module distributed with
674 OVS, particular Linux distribution kernels versions may provide diminished
675 functionality. This typically affects active FTP data connections when
676 using "actions=ct(alg=ftp),..." in flow tables. Specifically:
677 * Centos 7.1 kernels (3.10.0-2xx) kernels are unable to correctly set
678 up expectations for FTP data connections in multiple zones,
679 eg "actions=ct(zone=1,alg=ftp),ct(zone=2,alg=ftp),...". Executing the
680 "ct" action for subsequent data connections may fail to determine that
681 the data connection is "related" to an existing connection.
682 * Centos 7.2 kernels (3.10.0-3xx) kernels may not establish FTP ALG state
683 correctly for NATed connections. As a result, flows that perform NAT,
684 eg "actions=ct(nat,ftp=alg,table=1),..." may fail to NAT the packet,
685 and will populate the "ct_state=inv" bit in the flow.
689 ---------------------
690 - Dropped support for Python older than version 2.7. As a consequence,
691 using Open vSwitch 2.5 or later on XenServer 6.5 or earlier (which
692 have Python 2.4) requires first installing Python 2.7.
694 * Group chaining (where one OpenFlow group triggers another) is
696 * OpenFlow 1.4+ "importance" is now considered for flow eviction.
697 * OpenFlow 1.4+ OFPTC_EVICTION is now implemented.
698 * OpenFlow 1.4+ OFPTC_VACANCY_EVENTS is now implemented.
699 * OpenFlow 1.4+ OFPMP_TABLE_DESC is now implemented.
700 * Allow modifying the ICMPv4/ICMPv6 type and code fields.
701 * OpenFlow 1.4+ OFPT_SET_ASYNC_CONFIG and OFPT_GET_ASYNC_CONFIG are
704 * New "out_group" keyword for OpenFlow 1.1+ matching on output group.
706 * Geneve tunnels can now match and set options and the OAM bit.
707 * The nonstandard GRE64 tunnel extension has been dropped.
708 - Support Multicast Listener Discovery (MLDv1 and MLDv2).
709 - Add 'symmetric_l3l4' and 'symmetric_l3l4+udp' hash functions.
710 - sFlow agent now reports tunnel and MPLS structures.
711 - New 'check-system-userspace', 'check-kmod' and 'check-kernel' Makefile
712 targets to run a new system testsuite. These tests can be run inside
713 a Vagrant box. See INSTALL.md for details
714 - Mark --syslog-target argument as deprecated. It will be removed in
715 the next OVS release.
716 - Added --user option to all daemons
717 - Add support for connection tracking through the new "ct" action
718 and "ct_state"/"ct_zone"/"ct_mark"/"ct_label" match fields. Only
719 available on Linux kernels with the connection tracking module loaded.
720 - Add experimental version of OVN. OVN, the Open Virtual Network, is a
721 system to support virtual network abstraction. OVN complements the
722 existing capabilities of OVS to add native support for virtual network
723 abstractions, such as virtual L2 and L3 overlays and security groups.
725 * DPDK ports may now be created via network scripts (see README.RHEL).
728 * Added multiqueue support to vhost-user
729 * Note: QEMU 2.5+ required for multiqueue support
732 ---------------------
733 - Flow table modifications are now atomic, meaning that each packet
734 now sees a coherent version of the OpenFlow pipeline. For
735 example, if a controller removes all flows with a single OpenFlow
736 "flow_mod", no packet sees an intermediate version of the OpenFlow
737 pipeline where only some of the flows have been deleted.
738 - Added support for SFQ, FQ_CoDel and CoDel qdiscs.
739 - Add bash command-line completion support for ovs-vsctl Please check
740 utilities/ovs-command-compgen.INSTALL.md for how to use.
741 - The MAC learning feature now includes per-port fairness to mitigate
742 MAC flooding attacks.
743 - New support for a "conjunctive match" OpenFlow extension, which
744 allows constructing OpenFlow matches of the form "field1 in
745 {a,b,c...} AND field2 in {d,e,f...}" and generalizations. For details,
746 see documentation for the "conjunction" action in ovs-ofctl(8).
747 - Add bash command-line completion support for ovs-appctl/ovs-dpctl/
748 ovs-ofctl/ovsdb-tool commands. Please check
749 utilities/ovs-command-compgen.INSTALL.md for how to use.
750 - The "learn" action supports a new flag "delete_learned" that causes
751 the learned flows to be deleted when the flow with the "learn" action
753 - Basic support for the Geneve tunneling protocol. It is not yet
754 possible to generate or match options. This is planned for a future
755 release. The protocol is documented at
756 http://tools.ietf.org/html/draft-gross-geneve-00
757 - The OVS database now reports controller rate limiting statistics.
758 - sflow now exports information about LACP-based bonds, port names, and
759 OpenFlow port numbers, as well as datapath performance counters.
760 - ovs-dpctl functionality is now available for datapaths integrated
761 into ovs-vswitchd, via ovs-appctl. Some existing ovs-appctl
762 commands are now redundant and will be removed in a future
763 release. See ovs-vswitchd(8) for details.
765 * OpenFlow 1.4 bundles are now supported for flow mods and port
766 mods. For flow mods, both 'atomic' and 'ordered' bundle flags
767 are trivially supported, as all bundled messages are executed
768 in the order they were added and all flow table modifications
769 are now atomic to the datapath. Port mods may not appear in
770 atomic bundles, as port status modifications are not atomic.
771 * IPv6 flow label and neighbor discovery fields are now modifiable.
772 * OpenFlow 1.5 extended registers are now supported.
773 * The OpenFlow 1.5 actset_output field is now supported.
774 * OpenFlow 1.5 Copy-Field action is now supported.
775 * OpenFlow 1.5 masked Set-Field action is now supported.
776 * OpenFlow 1.3+ table features requests are now supported (read-only).
777 * Nicira extension "move" actions may now be included in action sets.
778 * "resubmit" actions may now be included in action sets. The resubmit
779 is executed last, and only if the action set has no "output" or "group"
781 * OpenFlow 1.4+ flow "importance" is now maintained in the flow table.
782 * A new Netronome extension to OpenFlow 1.5+ allows control over the
783 fields hashed for OpenFlow select groups. See "selection_method" and
784 related options in ovs-ofctl(8) for details.
785 - ovs-ofctl has a new '--bundle' option that makes the flow mod commands
786 ('add-flow', 'add-flows', 'mod-flows', 'del-flows', and 'replace-flows')
787 use an OpenFlow 1.4 bundle to operate the modifications as a single
788 atomic transaction. If any of the flow mods in a transaction fail, none
789 of them are executed. All flow mods in a bundle appear to datapath
790 lookups simultaneously.
791 - ovs-ofctl 'add-flow' and 'add-flows' commands now accept arbitrary flow
792 mods as an input by allowing the flow specification to start with an
793 explicit 'add', 'modify', 'modify_strict', 'delete', or 'delete_strict'
794 keyword. A missing keyword is treated as 'add', so this is fully
795 backwards compatible. With the new '--bundle' option all the flow mods
796 are executed as a single atomic transaction using an OpenFlow 1.4 bundle.
797 - ovs-pki: Changed message digest algorithm from MD5 to SHA-1 because
798 MD5 is no longer secure and some operating systems have started to disable
800 - ovsdb-server: New OVSDB protocol extension allows inequality tests on
801 "optional scalar" columns. See ovsdb-server(1) for details.
802 - ovs-vsctl now permits immutable columns in a new row to be modified in
803 the same transaction that creates the row.
804 - test-controller has been renamed ovs-testcontroller at request of users
805 who find it useful for testing basic OpenFlow setups. It is still not
806 a necessary or desirable part of most Open vSwitch deployments.
807 - Support for travis-ci.org based continuous integration builds has been
808 added. Build failures are reported to build@openvswitch.org. See INSTALL.md
809 file for additional details.
810 - Support for the Rapid Spanning Tree Protocol (IEEE 802.1D-2004).
811 The implementation has been tested successfully against the Ixia Automated
812 Network Validation Library (ANVL).
813 - Stats are no longer updated on fake bond interface.
814 - Keep active bond slave selection across OVS restart.
815 - A simple wrapper script, 'ovs-docker', to integrate OVS with Docker
816 containers. If and when there is a native integration of Open vSwitch
817 with Docker, the wrapper script will be retired.
818 - Added support for DPDK Tunneling. VXLAN, GRE, and Geneve are supported
819 protocols. This is generic tunneling mechanism for userspace datapath.
820 - Support for multicast snooping (IGMPv1, IGMPv2 and IGMPv3)
821 - Support for Linux kernels up to 4.0.x
822 - The documentation now use the term 'destination' to mean one of syslog,
823 console or file for vlog logging instead of the previously used term
825 - Support for VXLAN Group Policy extension
826 - Initial support for the IETF Auto-Attach SPBM draft standard. This
827 contains rudimentary support for the LLDP protocol as needed for
829 - The default OpenFlow and OVSDB ports are now the IANA-assigned
830 numbers. OpenFlow is 6653 and OVSDB is 6640.
831 - Support for DPDK vHost.
832 - Support for outer UDP checksums in Geneve and VXLAN.
833 - The kernel vports with dependencies are no longer part of the overall
834 openvswitch.ko but built and loaded automatically as individual kernel
835 modules (vport-*.ko).
836 - Support for STT tunneling.
837 - ovs-sim: New developer tool for simulating multiple OVS instances.
838 See ovs-sim(1) for more information.
839 - Support to configure method (--syslog-method argument) that determines
840 how daemons will talk with syslog.
841 - Support for "ovs-appctl vlog/list-pattern" command that lets to query
842 logging message format for each destination.
846 ---------------------
847 - OpenFlow 1.1, 1.2, and 1.3 are now enabled by default in
849 - Linux kernel datapath now has an exact match cache optimizing the
850 flow matching process.
851 - Datapath flows now have partially wildcarded tranport port field
852 matches. This reduces userspace upcalls, but increases the
853 number of different masks in the datapath. The kernel datapath
854 exact match cache removes the overhead of matching the incoming
855 packets with the larger number of masks, but when paired with an
856 older kernel module, some workloads may perform worse with the
858 - Compatibility with autoconf 2.63 (previously >=2.64)
860 v2.2.0 - Internal Release
861 ---------------------
862 - Internal ports are no longer brought up by default, because it
863 should be an administrator task to bring up devices as they are
865 - ovs-vsctl now reports when ovs-vswitchd fails to create a new port or
867 - Port creation and configuration errors are now stored in a new error
868 column of the Interface table and included in 'ovs-vsctl show'.
869 - The "ovsdbmonitor" graphical tool has been removed, because it was
870 poorly maintained and not widely used.
871 - New "check-ryu" Makefile target for running Ryu tests for OpenFlow
872 controllers against Open vSwitch. See INSTALL.md for details.
873 - Added IPFIX support for SCTP flows and templates for ICMPv4/v6 flows.
874 - Upon the receipt of a SIGHUP signal, ovs-vswitchd no longer reopens its
875 log file (it will terminate instead). Please use 'ovs-appctl vlog/reopen'
877 - Support for Linux kernels up to 3.14. From Kernel 3.12 onwards OVS uses
878 tunnel API for GRE and VXLAN.
879 - Added DPDK support.
880 - Added support for custom vlog patterns in Python
884 ---------------------
885 - Address prefix tracking support for flow tables. New columns
886 "prefixes" in OVS-DB table "Flow_Table" controls which packet
887 header fields are used for address prefix tracking. Prefix
888 tracking allows the classifier to skip rules with longer than
889 necessary prefixes, resulting in better wildcarding for datapath
890 flows. Default configuration is to not use any fields for prefix
891 tracking. However, if any flow tables contain both exact matches
892 and masked matches for IP address fields, OVS performance may be
893 increased by using this feature.
894 * As of now, the fields for which prefix lookup can be enabled
895 are: 'tun_id', 'tun_src', 'tun_dst', 'nw_src', 'nw_dst' (or
896 aliases 'ip_src' and 'ip_dst'), 'ipv6_src', and 'ipv6_dst'.
897 (Using this feature for 'tun_id' would only make sense if the
898 tunnel IDs have prefix structure similar to IP addresses.)
899 * There is a maximum number of fields that can be enabled for any
900 one flow table. Currently this limit is 3.
902 $ ovs-vsctl set Bridge br0 flow_tables:0=@N1 -- \
903 --id=@N1 create Flow_Table name=table0
904 $ ovs-vsctl set Bridge br0 flow_tables:1=@N1 -- \
905 --id=@N1 create Flow_Table name=table1
906 $ ovs-vsctl set Flow_Table table0 prefixes=ip_dst,ip_src
907 $ ovs-vsctl set Flow_Table table1 prefixes=[]
908 - TCP flags matching: OVS now supports matching of TCP flags. This
909 has an adverse performance impact when using OVS userspace 1.10
910 or older (no megaflows support) together with the new OVS kernel
911 module. It is recommended that the kernel and userspace modules
912 both are upgraded at the same time.
913 - The default OpenFlow and OVSDB ports will change to
914 IANA-assigned numbers in a future release. Consider updating
915 your installations to specify port numbers instead of using the
918 * The OpenFlow 1.1+ "Write-Actions" instruction is now supported.
919 * OVS limits the OpenFlow port numbers it assigns to port 32767 and
920 below, leaving port numbers above that range free for assignment
922 * ovs-vswitchd now honors changes to the "ofport_request" column
923 in the Interface table by changing the port's OpenFlow port
925 * The Open vSwitch software switch now supports OpenFlow groups.
926 - ovs-vswitchd.conf.db.5 man page will contain graphviz/dot
927 diagram only if graphviz package was installed at the build time.
928 - Support for Linux kernels up to 3.11
930 The "show" command also displays mega flow mask stats.
932 * New command "ofp-parse-pcap" to dump OpenFlow from PCAP files.
933 - ovs-controller has been renamed test-controller. It is no longer
934 packaged or installed by default, because too many users assumed
935 incorrectly that ovs-controller was a necessary or desirable part
936 of an Open vSwitch deployment.
937 - Added vlog option to export to a UDP syslog sink.
939 * The "monitor" command can now monitor all tables in a database,
940 instead of being limited to a single table.
941 - The flow-eviction-threshold has been replaced by the flow-limit which is a
942 hard limit on the number of flows in the datapath. It defaults to 200,000
943 flows. OVS automatically adjusts this number depending on network
945 - Added IPv6 support for active and passive socket communications.
949 ---------------------
950 - The ovs-vswitchd process is no longer single-threaded. Multiple
951 threads are now used to handle flow set up and asynchronous
954 * Experimental support for OpenFlow 1.1 (in addition to 1.2 and
955 1.3, which had experimental support in 1.10).
956 * Experimental protocol support for OpenFlow 1.1+ groups. This
957 does not yet include an implementation in the Open vSwitch
959 * Experimental protocol support for OpenFlow 1.2+ meters. This
960 does not yet include an implementation in the Open vSwitch
962 * New support for matching outer source and destination IP address
963 of tunneled packets, for tunnel ports configured with the newly
964 added "remote_ip=flow" and "local_ip=flow" options.
965 * Support for matching on metadata 'pkt_mark' for interacting with
966 other system components. On Linux this corresponds to the skb
968 * Support matching, rewriting SCTP ports
969 - The Interface table in the database has a new "ifindex" column to
970 report the interface's OS-assigned ifindex.
971 - New "check-oftest" Makefile target for running OFTest against Open
972 vSwitch. See README-OFTest for details.
973 - The flow eviction threshold has been moved to the Open_vSwitch table.
974 - Database names are now mandatory when specifying ovsdb-server options
975 through database paths (e.g. Private key option with the database name
976 should look like "--private-key=db:Open_vSwitch,SSL,private_key").
977 - Added ovs-dev.py, a utility script helpful for Open vSwitch developers.
978 - Support for Linux kernels up to 3.10
980 * New "ofp-parse" for printing OpenFlow messages read from a file.
981 * New commands for OpenFlow 1.1+ groups.
982 - Added configurable flow caching support to IPFIX exporter.
983 - Dropped support for Linux pre-2.6.32.
984 - Log file timestamps and ovsdb commit timestamps are now reported
985 with millisecond resolution. (Previous versions only reported
989 v1.11.0 - 28 Aug 2013
990 ---------------------
991 - Support for megaflows, which allows wildcarding in the kernel (and
992 any dpif implementation that supports wildcards). Depending on
993 the flow table and switch configuration, flow set up rates are
994 close to the Linux bridge.
995 - The "tutorial" directory contains a new tutorial for some advanced
996 Open vSwitch features.
997 - Stable bond mode has been removed.
998 - The autopath action has been removed.
999 - New support for the data encapsulation format of the LISP tunnel
1000 protocol (RFC 6830). An external control plane or manual flow
1001 setup is required for EID-to-RLOC mapping.
1003 * The "dec_mpls_ttl" and "set_mpls_ttl" actions from OpenFlow
1004 1.1 and later are now implemented.
1005 * New "stack" extension for use in actions, to push and pop from
1007 * The "load" and "set_field" actions can now modify the "in_port". (This
1008 allows one to enable output to a flow's input port by setting the
1009 in_port to some unused value, such as OFPP_NONE.)
1011 * New debugging commands "add-flow", "mod-flow", "del-flow".
1012 * "dump-flows" now has a -m option to increase output verbosity.
1013 - In dpif-based bridges, cache action translations, which can improve
1014 flow set up performance by 80% with a complicated flow table.
1015 - New syslog format, prefixed with "ovs|", to be easier to filter.
1016 - RHEL: Removes the default firewall rule that allowed GRE traffic to
1017 pass through. Any users that relied on this automatic firewall hole
1018 will have to manually configure it. The ovs-ctl(8) manpage documents
1019 the "enable-protocol" command that can be used as an alternative.
1020 - New CFM demand mode which uses data traffic to indicate interface
1023 v1.10.0 - 01 May 2013
1024 ---------------------
1025 - Bridge compatibility support has been removed. Any uses that
1026 rely on ovs-brcompatd will have to stick with Open vSwitch 1.9.x
1027 or adapt to native Open vSwitch support (e.g. use ovs-vsctl instead
1029 - The maximum size of the MAC learning table is now configurable.
1030 - With the Linux datapath, packets for new flows are now queued
1031 separately on a per-port basis, so it should no longer be
1032 possible for a large number of new flows arriving on one port to
1033 prevent new flows from being processed on other ports.
1035 * Previously ovs-vsctl would retry connecting to the database forever,
1036 causing it to hang if ovsdb-server was not running. Now, ovs-vsctl
1037 only tries once by default (use --retry to try forever). This change
1038 means that you may want to remove uses of --timeout to avoid hangs
1040 * Many "ovs-vsctl" database commands now accept an --if-exists option.
1041 Please refer to the ovs-vsctl manpage for details.
1043 - Experimental support for newer versions of OpenFlow. See
1044 the "What versions of OpenFlow does Open vSwitch support?"
1045 question in the FAQ for more details.
1046 - The OpenFlow "dp_desc" may now be configured by setting the
1047 value of other-config:dp-desc in the Bridge table.
1048 - It is possible to request the OpenFlow port number with the
1049 "ofport_request" column in the Interface table.
1050 - The NXM flow_removed message now reports the OpenFlow table ID
1051 from which the flow was removed.
1053 - New support for the VXLAN tunnel protocol (see the IETF draft here:
1054 http://tools.ietf.org/html/draft-mahalingam-dutt-dcops-vxlan-03).
1055 - Tunneling requires the version of the kernel module paired with
1056 Open vSwitch 1.9.0 or later.
1057 - Inheritance of the Don't Fragment bit in IP tunnels (df_inherit)
1058 is no longer supported.
1059 - Path MTU discovery is no longer supported.
1060 - CAPWAP tunneling support removed.
1061 - Tunnels with multicast destination ports are no longer supported.
1063 - The "dump-flows" and "del-flows" no longer require an argument
1064 if only one datapath exists.
1066 - New "vlog/disable-rate-limit" and "vlog/enable-rate-limit"
1067 commands available allow control over logging rate limits.
1068 - New "dpif/dump-dps", "dpif/show", and "dpif/dump-flows" command
1069 that mimic the equivalent ovs-dpctl commands.
1070 - The ofproto library is now responsible for assigning OpenFlow port
1071 numbers. An ofproto implementation should assign them when
1072 port_construct() is called.
1073 - All dpif-based bridges of a particular type share a common
1074 datapath called "ovs-<type>", e.g. "ovs-system". The ovs-dpctl
1075 commands will now return information on that shared datapath. To
1076 get the equivalent bridge-specific information, use the new
1077 "ovs-appctl dpif/*" commands.
1078 - Backward-incompatible changes:
1079 - Earlier Open vSwitch versions treated ANY as a wildcard in flow
1080 syntax. OpenFlow 1.1 adds a port named ANY, which introduces a
1081 conflict. ANY was rarely used in flow syntax, so we chose to
1082 retire that meaning of ANY in favor of the OpenFlow 1.1 meaning.
1083 - Patch ports no longer require kernel support, so they now work
1084 with FreeBSD and the kernel module built into Linux 3.3 and later.
1085 - New "sample" action.
1088 v1.9.0 - 26 Feb 2013
1089 ------------------------
1091 - Support for ipv6 set action.
1092 - SKB mark matching and setting.
1093 - support for Linux kernels up to 3.8
1094 - FreeBSD is now a supported platform, thanks to code contributions from
1095 Gaetano Catalli, Ed Maste, and Giuseppe Lettieri.
1096 - ovs-bugtool: New --ovs option to report only OVS related information.
1097 - New %t and %T log escapes to identify the subprogram within a
1098 cooperating group of processes or threads that emitted a log message.
1099 The default log patterns now include this information.
1101 - Allow bitwise masking for SHA and THA fields in ARP, SLL and TLL
1102 fields in IPv6 neighbor discovery messages, and IPv6 flow label.
1103 - Adds support for writing to the metadata field for a flow.
1105 - The tunneling code no longer assumes input and output keys are
1106 symmetric. If they are not, PMTUD needs to be disabled for
1107 tunneling to work. Note this only applies to flow-based keys.
1108 - New support for a nonstandard form of GRE that supports a 64-bit key.
1109 - Tunnel Path MTU Discovery default value was set to 'disabled'.
1110 This feature is deprecated and will be removed soon.
1111 - Tunnel header caching removed.
1113 - Commands and actions that accept port numbers now also accept keywords
1114 that represent those ports (such as LOCAL, NONE, and ALL). This is
1115 also the recommended way to specify these ports, for compatibility
1116 with OpenFlow 1.1 and later (which use the OpenFlow 1.0 numbers
1117 for these ports for different purposes).
1119 - Support requesting the port number with the "port_no" option in
1120 the "add-if" command.
1121 - ovs-pki: The "online PKI" features have been removed, along with
1122 the ovs-pki-cgi program that facilitated it, because of some
1123 alarmist insecurity claims. We do not believe that these claims
1124 are true, but because we do not know of any users for this
1125 feature it seems better on balance to remove it. (The ovs-pki-cgi
1126 program was not included in distribution packaging.)
1127 - ovsdb-server now enforces the immutability of immutable columns. This
1128 was not enforced in earlier versions due to an oversight.
1129 - The following features are now deprecated. They will be removed no
1130 earlier than February 2013. Please email dev@openvswitch.org with
1132 - Bridge compatibility.
1134 - The autopath action.
1135 - Interface type "null".
1136 - Numeric values for reserved ports (see "ovs-ofctl" note above).
1137 - Tunnel Path MTU Discovery.
1138 - CAPWAP tunnel support.
1139 - The data in the RARP packets can now be matched in the same way as the
1140 data in ARP packets.
1143 v1.8.0 - 26 Feb 2013
1144 ------------------------
1145 *** Internal only release ***
1146 - New FAQ. Please send updates and additions!
1147 - Authors of controllers, please read the new section titled "Action
1148 Reproduction" in DESIGN, which describes an Open vSwitch change in
1149 behavior in corner cases that may affect some controllers.
1151 - A new test utility that can create L3 tunnel between two Open
1152 vSwitches and detect connectivity issues.
1154 - New --sort and --rsort options for "dump-flows" command.
1155 - "mod-port" command can now control all OpenFlow config flags.
1157 - Allow general bitwise masking for IPv4 and IPv6 addresses in
1158 IPv4, IPv6, and ARP packets. (Previously, only CIDR masks
1160 - Allow support for arbitrary Ethernet masks. (Previously, only
1161 the multicast bit in the destination address could be individually
1163 - New field OXM_OF_METADATA, to align with OpenFlow 1.1.
1164 - The OFPST_QUEUE request now reports an error if a specified port or
1165 queue does not exist, or for requests for a specific queue on all
1166 ports, if the specified queue does not exist on any port. (Previous
1167 versions generally reported an empty set of results.)
1168 - New "flow monitor" feature to allow controllers to be notified of
1169 flow table changes as they happen.
1170 - Additional protocols are not mirrored and dropped when forward-bpdu is
1171 false. For a full list, see the ovs-vswitchd.conf.db man page.
1172 - Open vSwitch now sends RARP packets in situations where it previously
1173 sent a custom protocol, making it consistent with behavior of QEMU and
1175 - All Open vSwitch programs and log files now show timestamps in UTC,
1176 instead the local timezone, by default.
1179 v1.7.0 - 30 Jul 2012
1180 ------------------------
1181 - kernel modules are renamed. openvswitch_mod.ko is now
1182 openvswitch.ko and brcompat_mod.ko is now brcompat.ko.
1183 - Increased the number of NXM registers to 8.
1184 - Added ability to configure DSCP setting for manager and controller
1185 connections. By default, these connections have a DSCP value of
1186 Internetwork Control (0xc0).
1187 - Added the granular link health statistics, 'cfm_health', to an
1190 - Added support to mask nd_target for ICMPv6 neighbor discovery flows.
1191 - Added support for OpenFlow 1.3 port description (OFPMP_PORT_DESC)
1194 - Added the "dump-ports-desc" command to retrieve port
1195 information using the new port description multipart messages.
1197 - Added support for spawning ovs-test server from the client.
1198 - Now ovs-test is able to automatically create test bridges and ports.
1199 - "ovs-dpctl dump-flows" now prints observed TCP flags in TCP flows.
1200 - Tripled flow setup performance.
1201 - The "coverage/log" command previously available through ovs-appctl
1202 has been replaced by "coverage/show". The new command replies with
1203 coverage counter values, instead of logging them.
1206 v1.6.1 - 25 Jun 2012
1207 ------------------------
1208 - Allow OFPP_CONTROLLER as the in_port for packet-out messages.
1211 v1.6.0 - 24 Feb 2012
1212 ------------------------
1213 *** Internal only release ***
1215 - LACP bonds no longer fall back to balance-slb when negotiations fail.
1216 Instead they drop traffic.
1217 - The default bond_mode changed from SLB to active-backup, to protect
1218 unsuspecting users from the significant risks of SLB bonds (which are
1219 documented in vswitchd/INTERNALS).
1220 - Load balancing can be disabled by setting the bond-rebalance-interval
1223 - Added support for bitwise matching on TCP and UDP ports.
1224 See ovs-ofctl(8) for more information.
1225 - NXM flow dumps now include times elapsed toward idle and hard
1227 - Added an OpenFlow extension NXT_SET_ASYNC_CONFIG that allows
1228 controllers more precise control over which OpenFlow messages they
1229 receive asynchronously.
1230 - New "fin_timeout" action.
1231 - Added "fin_timeout" support to "learn" action.
1232 - New Nicira action NXAST_CONTROLLER that offers additional features
1233 over output to OFPP_CONTROLLER.
1234 - When QoS settings for an interface do not configure a default queue
1235 (queue 0), Open vSwitch now uses a default configuration for that
1236 queue, instead of dropping all packets as in previous versions.
1238 - Logging to console and file will have UTC timestamp as a default for
1239 all the daemons. An example of the default format is
1240 2012-01-27T16:35:17Z. ovs-appctl can be used to change the default
1242 - The syntax of commands and options to set log levels was simplified,
1243 to make it easier to remember.
1244 - New support for limiting the number of flows in an OpenFlow flow
1245 table, with configurable policy for evicting flows upon
1246 overflow. See the Flow_Table table in ovs-vswitch.conf.db(5)
1247 for more information.
1248 - New "enable-async-messages" column in the Controller table. If set to
1249 false, OpenFlow connections to the controller will initially have all
1250 asynchronous messages disabled, overriding normal OpenFlow behavior.
1251 - ofproto-provider interface:
1252 - "struct rule" has a new member "used" that ofproto implementations
1253 should maintain by updating with ofproto_rule_update_used().
1255 - The new option --timestamp causes the "monitor" command to print
1256 a timestamp with every update.
1257 - CFM module CCM broadcasts can now be tagged with an 802.1p priority.
1260 v1.5.0 - 01 Jun 2012
1261 ------------------------
1263 - Added support for querying, modifying, and deleting flows
1264 based on flow cookie when using NXM.
1265 - Added new NXM_PACKET_IN format.
1266 - Added new NXAST_DEC_TTL action.
1268 - Added daemonization support to the monitor and snoop commands.
1270 - The "find" command supports new set relational operators
1271 {=}, {!=}, {<}, {>}, {<=}, and {>=}.
1272 - ovsdb-tool now uses the typical database and schema installation
1273 directories as defaults.
1274 - The default MAC learning timeout has been increased from 60 seconds
1275 to 300 seconds. The MAC learning timeout is now configurable.
1278 v1.4.0 - 30 Jan 2012
1279 ------------------------
1280 - Compatible with Open vSwitch kernel module included in Linux 3.3.
1281 - New "VLAN splinters" feature to work around buggy device drivers
1282 in old Linux versions. (This feature is deprecated. When
1283 broken device drivers are no longer in widespread use, we will
1284 delete this feature.) See ovs-vswitchd.conf.db(5) for more
1287 - Added ability to match on IPv6 flow label through NXM.
1288 - Added ability to match on ECN bits in IPv4 and IPv6 through NXM.
1289 - Added ability to match on TTL in IPv4 and IPv6 through NXM.
1290 - Added ability to modify ECN bits in IPv4.
1291 - Added ability to modify TTL in IPv4.
1293 - Don't require the "normal" action to use mirrors. Traffic will
1294 now be properly mirrored for any flows, regardless of their
1296 - Track packet and byte statistics sent on mirrors.
1297 - The sFlow implementation can now usually infer the correct agent
1298 device instead of having to be told explicitly.
1300 - New "fdb/flush" command to flush bridge's MAC learning table.
1302 - A new distributed testing tool that allows one to diagnose performance
1303 and connectivity issues. This tool currently is not included in RH or
1305 - RHEL packaging now supports integration with Red Hat network scripts.
1307 - Post 1.4.*, OVS will be changing the default bond mode from balance-slb
1308 to active-backup. SLB bonds carry significant risks with them
1309 (documented vswitchd/INTERNALS) which we want to prevent unsuspecting
1310 users from running into. Users are advised to update any scripts or
1311 configuration which may be negatively impacted by explicitly setting
1312 the bond mode which they want to use.
1315 v1.3.0 - 09 Dec 2011
1316 ------------------------
1318 - Added an OpenFlow extension which allows the "output" action to accept
1320 - Added an OpenFlow extension for flexible learning.
1321 - Bumped number of NXM registers from four to five.
1323 - New "version" command to determine version of running daemon.
1324 - If no argument is provided for "cfm/show", displays detailed
1325 information about all interfaces with CFM enabled.
1326 - If no argument is provided for "lacp/show", displays detailed
1327 information about all ports with LACP enabled.
1329 - New "set-if" command to modify a datapath port's configuration.
1331 - The software switch now supports 255 OpenFlow tables, instead
1332 of just one. By default, only table 0 is consulted, but the
1333 new NXAST_RESUBMIT_TABLE action can look up in additional
1334 tables. Tables 128 and above are reserved for use by the
1335 switch itself; please use only tables 0 through 127.
1336 - Add support for 802.1D spanning tree (STP).
1337 - Fragment handling extensions:
1338 - New OFPC_FRAG_NX_MATCH fragment handling mode, in which L4
1339 fields are made available for matching in fragments with
1341 - New NXM_NX_IP_FRAG match field for matching IP fragments (usable
1342 via "ip_frag" in ovs-ofctl).
1343 - New ovs-ofctl "get-frags" and "set-frags" commands to get and set
1344 fragment handling policy.
1345 - CAPWAP tunneling now supports an extension to transport a 64-bit key.
1346 By default it remains compatible with the old version and other
1347 standards-based implementations.
1348 - Flow setups are now processed in a round-robin manner across ports
1349 to prevent any single client from monopolizing the CPU and conducting
1350 a denial of service attack.
1351 - Added support for native VLAN tagging. A new "vlan_mode"
1352 parameter can be set for "port". Possible values: "access",
1353 "trunk", "native-tagged" and "native-untagged".
1354 - test-openflowd has been removed. Please use ovs-vswitchd instead.
1356 v1.2.0 - 03 Aug 2011
1357 ------------------------
1358 - New "ofproto" abstraction layer to ease porting to hardware
1360 - Packaging for Red Hat Enterprise Linux 5.6 and 6.0.
1361 - Datapath support for Linux kernels up to 3.0.
1363 - New "bundle" and "bundle_load" action extensions.
1365 - Implement table unique constraints.
1366 - Support cooperative locking between callers.
1368 - New "-s" option for "show" command prints packet and byte
1369 counters for each port.
1371 - New "--readd" option for "replace-flows".
1373 - New "show" command to print an overview of configuration.
1374 - New "comment" command to add remark that explains intentions.
1375 - ovs-brcompatd has been rewritten to fix long-standing bugs.
1376 - ovs-openflowd has been renamed test-openflowd and moved into the
1377 tests directory. Its presence confused too many users. Please
1378 use ovs-vswitchd instead.
1379 - New ovs-benchmark utility to test flow setup performance.
1380 - A new log level "off" has been added. Configuring a log facility
1381 "off" prevents any messages from being logged to it. Previously,
1382 "emer" was effectively "off" because no messages were ever logged at
1383 level "emer". Now, errors that cause a process to exit are logged
1385 - "configure" option --with-l26 has been renamed --with-linux, and
1386 --with-l26-source has been renamed --with-linux-source. The old
1387 names will be removed after the next release, so please update
1389 - The "-2.6" suffix has been dropped from the datapath/linux-2.6 and
1390 datapath/linux-2.6/compat-2.6 directories.
1392 - Dropped support for "tun_id_from_cookie" OpenFlow extension.
1393 Please use the extensible match extensions instead.
1394 - Removed the Maintenance_Point and Monitor tables in an effort
1395 to simplify 802.1ag configuration.
1396 - Performance and scalability improvements
1399 v1.1.0 - 05 Apr 2011
1400 ------------------------
1401 - Ability to define policies over IPv6
1404 - Support for extensible match extensions to OpenFlow
1406 - Support for HFSC qdisc.
1407 - Queue used by in-band control can now be configured.
1409 - Kernel<->userspace interface has been reworked and should be
1410 close to a stable ABI now.
1411 - "Port group" concept has been dropped.
1412 - GRE over IPSEC tunnels
1414 - New active backup bonding mode.
1415 - New L4 hashing support when LACP is enabled.
1416 - Source MAC hash now includes VLAN field also.
1418 - Greatly improved handling of large flow tables
1420 - "show" command now prints full vport configuration.
1421 - "dump-groups" command removed since kernel support for
1422 port groups was dropped.
1424 - New commands for working with the new Managers table.
1425 - "list" command enhanced with new formatting options and --columns
1427 - "get" command now accepts new --id option.
1428 - New "find" command.
1430 - New "queue-stats" command for printing queue stats.
1431 - New commands "replace-flows" and "diff-flows".
1432 - Commands to add and remove flows can now read from files.
1433 - New --flow-format option to enable or disable NXM.
1434 - New --more option to increase OpenFlow message verbosity.
1435 - Removed "tun-cookie" command, which is no longer useful.
1436 - ovs-controller enhancements for testing various features.
1437 - New ovs-vlan-test command for testing for Linux kernel driver VLAN
1438 bugs. New ovs-vlan-bug-workaround command for enabling and
1439 disabling a workaround for these driver bugs.
1441 - "Resubmit" actions now update flow statistics.
1442 - New "register" extension for use in matching and actions, via NXM.
1443 - New "multipath" experimental action extension.
1444 - New support for matching multicast Ethernet frames, via NXM.
1445 - New extension for OpenFlow vendor error codes.
1446 - New extension to set the QoS output queue without actually
1447 sending to an output port.
1448 - Open vSwitch now reports a single flow table, instead of
1449 separate hash and wildcard tables. This better models the
1450 current implementation.
1451 - New experimental "note" action.
1452 - New "ofproto/trace" ovs-appctl command and associated utilities
1453 to ease debugging complex flow tables.
1455 - Schema documentation now includes an entity-relationship diagram.
1456 - The database is now garbage collected. In most tables,
1457 unreferenced rows will be deleted automatically.
1458 - Many tables now include statistics updated periodically by
1459 ovs-vswitchd or ovsdb-server.
1460 - Every table now has an "external-ids" column for use by OVS
1462 - There is no default controller anymore. Each bridge must have its
1463 controller individually specified.
1464 - The "fail-mode" is now a property of a Bridge instead of a Controller.
1465 - New versioning and checksum features.
1466 - New Managers table and manager_options column in Open_vSwitch table
1467 for specifying managers. The old "managers" column in the
1468 Open_vSwitch table has been removed.
1469 - Many "name" columns are now immutable.
1471 - Dropped support for XenServer pre-5.6.100.
1472 - Dropped support for Linux pre-2.6.18.
1473 - Dropped controller discovery support.
1474 - Dropped "ovs-ofctl status" and the OpenFlow extension that it used.
1475 Statistics reporting in the database is a rough equivalent.
1476 - Dropped the "corekeeper" package (now separate, at
1477 http://openvswitch.org/cgi-bin/gitweb.cgi?p=corekeeper).
1478 - Performance and scalability improvements
1481 v1.1.0pre2 - 13 Sep 2010
1482 ------------------------
1485 v1.1.0pre1 - 31 Aug 2010
1486 ------------------------
1487 - OpenFlow 1.0 slicing (QoS) functionality
1488 - Python bindings for configuration database (no write support)
1489 - Performance and scalability improvements
1492 v1.0.1 - 31 May 2010
1493 --------------------
1494 - New "patch" interface type
1497 v1.0.0 - 15 May 2010
1498 --------------------
1499 - Configuration database with remote management
1502 - Support for XenServer 5.5 and 5.6
1503 - Performance and scalability improvements
1506 v0.99.2 - 18 Feb 2010
1507 ---------------------
1510 v0.99.1 - 25 Jan 2010
1511 ---------------------
1512 - Add support for sFlow(R)
1513 - Make headers compatible with C++
1516 v0.99.0 - 14 Jan 2010
1517 ---------------------
1518 - User-space forwarding engine
1521 v0.90.7 - 29 Nov 2009
1522 ---------------------
1523 - Add support for NetFlow active timeouts
1526 v0.90.6 - 6 Oct 2009
1527 --------------------
1530 v0.90.5 - 21 Sep 2009
1531 ---------------------
1532 - Generalize in-band control to more diverse network setups
projects / ovs.git / blob