2 * Device Tree file for the Linksys WRT1900AC (Mamba).
4 * Note: this board is shipped with a new generation boot loader that
5 * remaps internal registers at 0xf1000000. Therefore, if earlyprintk
6 * is used, the CONFIG_DEBUG_MVEBU_UART0_ALTERNATE option should be
9 * Copyright (C) 2014 Imre Kaloz <kaloz@openwrt.org>
11 * Based on armada-xp-axpwifiap.dts:
13 * Copyright (C) 2013 Marvell
15 * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
17 * This file is dual-licensed: you can use it either under the terms
18 * of the GPL or the X11 license, at your option. Note that this dual
19 * licensing only applies to this file, and not this project as a
22 * a) This file is licensed under the terms of the GNU General Public
23 * License version 2. This program is licensed "as is" without
24 * any warranty of any kind, whether express or implied.
28 * b) Permission is hereby granted, free of charge, to any person
29 * obtaining a copy of this software and associated documentation
30 * files (the "Software"), to deal in the Software without
31 * restriction, including without limitation the rights to use,
32 * copy, modify, merge, publish, distribute, sublicense, and/or
33 * sell copies of the Software, and to permit persons to whom the
34 * Software is furnished to do so, subject to the following
37 * The above copyright notice and this permission notice shall be
38 * included in all copies or substantial portions of the Software.
40 * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
41 * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
42 * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
43 * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
44 * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
45 * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
46 * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
47 * OTHER DEALINGS IN THE SOFTWARE.
51 #include <dt-bindings/gpio/gpio.h>
52 #include <dt-bindings/input/input.h>
53 #include "armada-xp-mv78230.dtsi"
56 model = "Linksys WRT1900AC";
57 compatible = "linksys,mamba", "marvell,armadaxp-mv78230",
58 "marvell,armadaxp", "marvell,armada-370-xp";
61 bootargs = "console=ttyS0,115200";
66 device_type = "memory";
67 reg = <0x00000000 0x00000000 0x00000000 0x10000000>; /* 256MB */
71 ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
72 MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
73 MBUS_ID(0x09, 0x09) 0 0 0xf1100000 0x10000
74 MBUS_ID(0x09, 0x05) 0 0 0xf1110000 0x10000>;
79 /* No crystal connected to the internal RTC */
83 /* J10: VCC, NC, RX, NC, TX, GND */
94 pinctrl-0 = <&ge0_rgmii_pins>;
95 pinctrl-names = "default";
97 phy-mode = "rgmii-id";
105 pinctrl-0 = <&ge1_rgmii_pins>;
106 pinctrl-names = "default";
108 phy-mode = "rgmii-id";
115 /* USB part of the eSATA/USB 2.0 port */
122 clock-frequency = <100000>;
125 compatible = "ti,tmp421";
130 #address-cells = <1>;
133 compatible = "ti,tlc59116";
137 label = "mamba:amber:wan";
142 label = "mamba:white:wan";
147 label = "mamba:white:wlan_2g";
152 label = "mamba:white:wlan_5g";
157 label = "mamba:white:esata";
162 label = "mamba:white:usb2";
167 label = "mamba:white:usb3_1";
172 label = "mamba:white:usb3_2";
177 label = "mamba:white:wps";
182 label = "mamba:amber:wps";
191 marvell,nand-keep-config;
192 marvell,nand-enable-arbiter;
194 nand-ecc-strength = <4>;
195 nand-ecc-step-size = <512>;
199 reg = <0x0000000 0x100000>; /* 1MB */
205 reg = <0x100000 0x40000>; /* 256KB */
210 reg = <0x140000 0x40000>; /* 256KB */
215 reg = <0x900000 0x100000>; /* 1MB */
219 /* kernel1 overlaps with rootfs1 by design */
222 reg = <0xa00000 0x2800000>; /* 40MB */
227 reg = <0xd00000 0x2500000>; /* 37MB */
230 /* kernel2 overlaps with rootfs2 by design */
233 reg = <0x3200000 0x2800000>; /* 40MB */
238 reg = <0x3500000 0x2500000>; /* 37MB */
242 * 38MB, last MB is for the BBT, not writable
246 reg = <0x5a00000 0x2600000>;
250 * Unused area between "s_env" and "devinfo".
251 * Moved here because otherwise the renumbered
252 * partitions would break the bootloader
256 label = "unused_area";
257 reg = <0x180000 0x780000>; /* 7.5MB */
264 compatible = "gpio-keys";
265 #address-cells = <1>;
267 pinctrl-0 = <&keys_pin>;
268 pinctrl-names = "default";
272 linux,code = <KEY_WPS_BUTTON>;
273 gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
277 label = "Factory Reset Button";
278 linux,code = <KEY_RESTART>;
279 gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
284 compatible = "gpio-leds";
285 pinctrl-0 = <&power_led_pin>;
286 pinctrl-names = "default";
289 label = "mamba:white:power";
290 gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
291 default-state = "on";
296 /* SUNON HA4010V4-0000-C99 */
297 compatible = "gpio-fan";
298 gpios = <&gpio0 24 0>;
300 gpio-fan,speed-map = <0 0
305 compatible = "marvell,dsa";
306 #address-cells = <2>;
309 dsa,ethernet = <ð0>;
310 dsa,mii-bus = <&mdio>;
313 #address-cells = <1>;
315 reg = <0x0 0>; /* MDIO address 0, switch 0 in tree */
353 /* Etron EJ168 USB 3.0 controller */
359 /* First mini-PCIe port */
365 /* Second mini-PCIe port */
375 marvell,pins = "mpp32", "mpp33";
376 marvell,function = "gpio";
379 power_led_pin: power-led-pin {
380 marvell,pins = "mpp40";
381 marvell,function = "gpio";
384 gpio_fan_pin: gpio-fan-pin {
385 marvell,pins = "mpp24";
386 marvell,function = "gpio";
394 #address-cells = <1>;
396 compatible = "everspin,mr25h256";
397 reg = <0>; /* Chip select 0 */
398 spi-max-frequency = <40000000>;