arch/arm/boot/dts/exynos4412-midas.dtsi

   1 // SPDX-License-Identifier: GPL-2.0
   2 /*
   3  * Samsung's Exynos4412 based Trats 2 board device tree source
   4  *
   5  * Copyright (c) 2013 Samsung Electronics Co., Ltd.
   6  *              http://www.samsung.com
   7  *
   8  * Device tree source file for Samsung's Trats 2 board which is based on
   9  * Samsung's Exynos4412 SoC.
  10  */
  11
  12 /dts-v1/;
  13 #include "exynos4412.dtsi"
  14 #include "exynos4412-ppmu-common.dtsi"
  15 #include <dt-bindings/gpio/gpio.h>
  16 #include <dt-bindings/interrupt-controller/irq.h>
  17 #include <dt-bindings/clock/maxim,max77686.h>
  18 #include <dt-bindings/pinctrl/samsung.h>
  19
  20 / {
  21         compatible = "samsung,midas", "samsung,exynos4412", "samsung,exynos4";
  22
  23         aliases {
  24                 i2c11 = &i2c_max77693;
  25                 i2c12 = &i2c_max77693_fuel;
  26         };
  27
  28         chosen {
  29                 stdout-path = &serial_2;
  30         };
  31
  32         firmware@204f000 {
  33                 compatible = "samsung,secure-firmware";
  34                 reg = <0x0204F000 0x1000>;
  35         };
  36
  37         fixed-rate-clocks {
  38                 xxti {
  39                         compatible = "samsung,clock-xxti", "fixed-clock";
  40                         clock-frequency = <0>;
  41                 };
  42
  43                 xusbxti {
  44                         compatible = "samsung,clock-xusbxti", "fixed-clock";
  45                         clock-frequency = <24000000>;
  46                 };
  47         };
  48
  49         cam_io_reg: voltage-regulator-1 {
  50                 compatible = "regulator-fixed";
  51                 regulator-name = "CAM_SENSOR_A";
  52                 regulator-min-microvolt = <2800000>;
  53                 regulator-max-microvolt = <2800000>;
  54                 enable-active-high;
  55                 status = "disabled";
  56         };
  57
  58         cam_af_reg: voltage-regulator-2 {
  59                 compatible = "regulator-fixed";
  60                 regulator-name = "CAM_AF";
  61                 regulator-min-microvolt = <2800000>;
  62                 regulator-max-microvolt = <2800000>;
  63                 enable-active-high;
  64                 status = "disabled";
  65         };
  66
  67         vsil12: voltage-regulator-3 {
  68                 compatible = "regulator-fixed";
  69                 regulator-name = "VSIL_1.2V";
  70                 regulator-min-microvolt = <1200000>;
  71                 regulator-max-microvolt = <1200000>;
  72                 gpio = <&gpl0 4 GPIO_ACTIVE_HIGH>;
  73                 enable-active-high;
  74                 vin-supply = <&buck7_reg>;
  75         };
  76
  77         vcc33mhl: voltage-regulator-4 {
  78                 compatible = "regulator-fixed";
  79                 regulator-name = "VCC_3.3_MHL";
  80                 regulator-min-microvolt = <3300000>;
  81                 regulator-max-microvolt = <3300000>;
  82                 gpio = <&gpl0 4 GPIO_ACTIVE_HIGH>;
  83                 enable-active-high;
  84         };
  85
  86         vcc18mhl: voltage-regulator-5 {
  87                 compatible = "regulator-fixed";
  88                 regulator-name = "VCC_1.8_MHL";
  89                 regulator-min-microvolt = <1800000>;
  90                 regulator-max-microvolt = <1800000>;
  91                 gpio = <&gpl0 4 GPIO_ACTIVE_HIGH>;
  92                 enable-active-high;
  93         };
  94
  95         gpio-keys {
  96                 compatible = "gpio-keys";
  97                 pinctrl-names = "default";
  98                 pinctrl-0 = <&gpio_keys>;
  99
 100                 key-down {
 101                         gpios = <&gpx3 3 GPIO_ACTIVE_LOW>;
 102                         linux,code = <114>;
 103                         label = "volume down";
 104                         debounce-interval = <10>;
 105                 };
 106
 107                 key-up {
 108                         gpios = <&gpx2 2 GPIO_ACTIVE_LOW>;
 109                         linux,code = <115>;
 110                         label = "volume up";
 111                         debounce-interval = <10>;
 112                 };
 113
 114                 key-power {
 115                         gpios = <&gpx2 7 GPIO_ACTIVE_LOW>;
 116                         linux,code = <116>;
 117                         label = "power";
 118                         debounce-interval = <10>;
 119                         wakeup-source;
 120                 };
 121
 122                 key-ok {
 123                         gpios = <&gpx0 1 GPIO_ACTIVE_LOW>;
 124                         linux,code = <139>;
 125                         label = "ok";
 126                         debounce-interval = <10>;
 127                         wakeup-source;
 128                 };
 129         };
 130
 131         i2c_max77693: i2c-gpio-1 {
 132                 compatible = "i2c-gpio";
 133                 gpios = <&gpm2 0 GPIO_ACTIVE_HIGH>, <&gpm2 1 GPIO_ACTIVE_HIGH>;
 134                 i2c-gpio,delay-us = <2>;
 135                 #address-cells = <1>;
 136                 #size-cells = <0>;
 137                 status = "okay";
 138
 139                 max77693@66 {
 140                         compatible = "maxim,max77693";
 141                         interrupt-parent = <&gpx1>;
 142                         interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
 143                         pinctrl-names = "default";
 144                         pinctrl-0 = <&max77693_irq>;
 145                         reg = <0x66>;
 146
 147                         regulators {
 148                                 esafeout1_reg: ESAFEOUT1 {
 149                                         regulator-name = "ESAFEOUT1";
 150                                 };
 151                                 esafeout2_reg: ESAFEOUT2 {
 152                                         regulator-name = "ESAFEOUT2";
 153                                 };
 154                                 charger_reg: CHARGER {
 155                                         regulator-name = "CHARGER";
 156                                         regulator-min-microamp = <60000>;
 157                                         regulator-max-microamp = <2580000>;
 158                                 };
 159                         };
 160
 161                         max77693_haptic {
 162                                 compatible = "maxim,max77693-haptic";
 163                                 haptic-supply = <&ldo26_reg>;
 164                                 pwms = <&pwm 0 38022 0>;
 165                         };
 166
 167                         charger {
 168                                 compatible = "maxim,max77693-charger";
 169
 170                                 maxim,constant-microvolt = <4350000>;
 171                                 maxim,min-system-microvolt = <3600000>;
 172                                 maxim,thermal-regulation-celsius = <100>;
 173                                 maxim,battery-overcurrent-microamp = <3500000>;
 174                                 maxim,charge-input-threshold-microvolt = <4300000>;
 175                         };
 176                 };
 177         };
 178
 179         i2c_max77693_fuel: i2c-gpio-3 {
 180                 compatible = "i2c-gpio";
 181                 gpios = <&gpf1 5 GPIO_ACTIVE_HIGH>, <&gpf1 4 GPIO_ACTIVE_HIGH>;
 182                 i2c-gpio,delay-us = <2>;
 183                 #address-cells = <1>;
 184                 #size-cells = <0>;
 185                 status = "okay";
 186
 187                 max77693-fuel-gauge@36 {
 188                         compatible = "maxim,max17047";
 189                         interrupt-parent = <&gpx2>;
 190                         interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
 191                         pinctrl-names = "default";
 192                         pinctrl-0 = <&max77693_fuel_irq>;
 193                         reg = <0x36>;
 194
 195                         maxim,over-heat-temp = <700>;
 196                         maxim,over-volt = <4500>;
 197                 };
 198         };
 199
 200         i2c-mhl {
 201                 compatible = "i2c-gpio";
 202                 gpios = <&gpf0 4 GPIO_ACTIVE_HIGH>, <&gpf0 6 GPIO_ACTIVE_HIGH>;
 203                 i2c-gpio,delay-us = <100>;
 204                 #address-cells = <1>;
 205                 #size-cells = <0>;
 206
 207                 pinctrl-0 = <&i2c_mhl_bus>;
 208                 pinctrl-names = "default";
 209                 status = "okay";
 210
 211                 sii9234: hdmi-bridge@39 {
 212                         compatible = "sil,sii9234";
 213                         avcc33-supply = <&vcc33mhl>;
 214                         iovcc18-supply = <&vcc18mhl>;
 215                         avcc12-supply = <&vsil12>;
 216                         cvcc12-supply = <&vsil12>;
 217                         reset-gpios = <&gpf3 4 GPIO_ACTIVE_LOW>;
 218                         interrupt-parent = <&gpf3>;
 219                         interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
 220                         reg = <0x39>;
 221
 222                         port {
 223                                 mhl_to_hdmi: endpoint {
 224                                         remote-endpoint = <&hdmi_to_mhl>;
 225                                 };
 226                         };
 227                 };
 228         };
 229
 230         wlan_pwrseq: sdhci3-pwrseq {
 231                 compatible = "mmc-pwrseq-simple";
 232                 reset-gpios = <&gpj0 0 GPIO_ACTIVE_LOW>;
 233                 clocks = <&max77686 MAX77686_CLK_PMIC>;
 234                 clock-names = "ext_clock";
 235         };
 236
 237         sound {
 238                 compatible = "samsung,trats2-audio";
 239                 samsung,i2s-controller = <&i2s0>;
 240                 samsung,model = "Trats2";
 241                 samsung,audio-codec = <&wm1811>;
 242                 samsung,audio-routing =
 243                         "SPK", "SPKOUTLN",
 244                         "SPK", "SPKOUTLP",
 245                         "SPK", "SPKOUTRN",
 246                         "SPK", "SPKOUTRP";
 247         };
 248
 249         thermistor-ap {
 250                 compatible = "murata,ncp15wb473";
 251                 pullup-uv = <1800000>;   /* VCC_1.8V_AP */
 252                 pullup-ohm = <100000>;   /* 100K */
 253                 pulldown-ohm = <100000>; /* 100K */
 254                 io-channels = <&adc 1>;  /* AP temperature */
 255         };
 256
 257         thermistor-battery {
 258                 compatible = "murata,ncp15wb473";
 259                 pullup-uv = <1800000>;   /* VCC_1.8V_AP */
 260                 pullup-ohm = <100000>;   /* 100K */
 261                 pulldown-ohm = <100000>; /* 100K */
 262                 io-channels = <&adc 2>;  /* Battery temperature */
 263         };
 264
 265         thermal-zones {
 266                 cpu_thermal: cpu-thermal {
 267                         cooling-maps {
 268                                 map0 {
 269                                      /* Corresponds to 800MHz at freq_table */
 270                                      cooling-device = <&cpu0 7 7>, <&cpu1 7 7>,
 271                                                       <&cpu2 7 7>, <&cpu3 7 7>;
 272                                 };
 273                                 map1 {
 274                                      /* Corresponds to 200MHz at freq_table */
 275                                      cooling-device = <&cpu0 13 13>,
 276                                                       <&cpu1 13 13>,
 277                                                       <&cpu2 13 13>,
 278                                                       <&cpu3 13 13>;
 279                                };
 280                        };
 281                 };
 282         };
 283 };
 284
 285 &adc {
 286         vdd-supply = <&ldo3_reg>;
 287         status = "okay";
 288 };
 289
 290 &bus_dmc {
 291         devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>;
 292         vdd-supply = <&buck1_reg>;
 293         status = "okay";
 294 };
 295
 296 &bus_acp {
 297         devfreq = <&bus_dmc>;
 298         status = "okay";
 299 };
 300
 301 &bus_c2c {
 302         devfreq = <&bus_dmc>;
 303         status = "okay";
 304 };
 305
 306 &bus_leftbus {
 307         devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>;
 308         vdd-supply = <&buck3_reg>;
 309         status = "okay";
 310 };
 311
 312 &bus_rightbus {
 313         devfreq = <&bus_leftbus>;
 314         status = "okay";
 315 };
 316
 317 &bus_display {
 318         devfreq = <&bus_leftbus>;
 319         status = "okay";
 320 };
 321
 322 &bus_fsys {
 323         devfreq = <&bus_leftbus>;
 324         status = "okay";
 325 };
 326
 327 &bus_peri {
 328         devfreq = <&bus_leftbus>;
 329         status = "okay";
 330 };
 331
 332 &bus_mfc {
 333         devfreq = <&bus_leftbus>;
 334         status = "okay";
 335 };
 336
 337 &camera {
 338         pinctrl-0 = <&cam_port_a_clk_active &cam_port_b_clk_active>;
 339         pinctrl-names = "default";
 340         status = "okay";
 341         assigned-clocks = <&clock CLK_MOUT_CAM0>,
 342                 <&clock CLK_MOUT_CAM1>;
 343         assigned-clock-parents = <&clock CLK_XUSBXTI>,
 344                 <&clock CLK_XUSBXTI>;
 345 };
 346
 347 &cpu0 {
 348         cpu0-supply = <&buck2_reg>;
 349 };
 350
 351 &csis_0 {
 352         status = "okay";
 353         vddcore-supply = <&ldo8_reg>;
 354         vddio-supply = <&ldo10_reg>;
 355         assigned-clocks = <&clock CLK_MOUT_CSIS0>,
 356                         <&clock CLK_SCLK_CSIS0>;
 357         assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
 358         assigned-clock-rates = <0>, <176000000>;
 359
 360         /* Camera C (3) MIPI CSI-2 (CSIS0) */
 361         port@3 {
 362                 reg = <3>;
 363                 csis0_ep: endpoint {
 364                         remote-endpoint = <&s5c73m3_ep>;
 365                         data-lanes = <1 2 3 4>;
 366                         samsung,csis-hs-settle = <12>;
 367                 };
 368         };
 369 };
 370
 371 &csis_1 {
 372         status = "okay";
 373         vddcore-supply = <&ldo8_reg>;
 374         vddio-supply = <&ldo10_reg>;
 375         assigned-clocks = <&clock CLK_MOUT_CSIS1>,
 376                         <&clock CLK_SCLK_CSIS1>;
 377         assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
 378         assigned-clock-rates = <0>, <176000000>;
 379
 380         /* Camera D (4) MIPI CSI-2 (CSIS1) */
 381         port@4 {
 382                 reg = <4>;
 383                 csis1_ep: endpoint {
 384                         remote-endpoint = <&is_s5k6a3_ep>;
 385                         data-lanes = <1>;
 386                         samsung,csis-hs-settle = <18>;
 387                         samsung,csis-wclk;
 388                 };
 389         };
 390 };
 391
 392 &dsi_0 {
 393         vddcore-supply = <&ldo8_reg>;
 394         vddio-supply = <&ldo10_reg>;
 395         samsung,burst-clock-frequency = <500000000>;
 396         samsung,esc-clock-frequency = <20000000>;
 397         samsung,pll-clock-frequency = <24000000>;
 398 };
 399
 400 &exynos_usbphy {
 401         vbus-supply = <&esafeout1_reg>;
 402         status = "okay";
 403 };
 404
 405 &fimc_0 {
 406         status = "okay";
 407         assigned-clocks = <&clock CLK_MOUT_FIMC0>,
 408                         <&clock CLK_SCLK_FIMC0>;
 409         assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
 410         assigned-clock-rates = <0>, <176000000>;
 411 };
 412
 413 &fimc_1 {
 414         status = "okay";
 415         assigned-clocks = <&clock CLK_MOUT_FIMC1>,
 416                         <&clock CLK_SCLK_FIMC1>;
 417         assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
 418         assigned-clock-rates = <0>, <176000000>;
 419 };
 420
 421 &fimc_2 {
 422         status = "okay";
 423         assigned-clocks = <&clock CLK_MOUT_FIMC2>,
 424                         <&clock CLK_SCLK_FIMC2>;
 425         assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
 426         assigned-clock-rates = <0>, <176000000>;
 427 };
 428
 429 &fimc_3 {
 430         status = "okay";
 431         assigned-clocks = <&clock CLK_MOUT_FIMC3>,
 432                         <&clock CLK_SCLK_FIMC3>;
 433         assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
 434         assigned-clock-rates = <0>, <176000000>;
 435 };
 436
 437 &fimc_is {
 438         pinctrl-0 = <&fimc_is_uart>;
 439         pinctrl-names = "default";
 440         status = "okay";
 441
 442         };
 443
 444 &fimc_lite_0 {
 445         status = "okay";
 446 };
 447
 448 &fimc_lite_1 {
 449         status = "okay";
 450 };
 451
 452 &fimd {
 453         status = "okay";
 454 };
 455
 456 &hdmi {
 457         hpd-gpios = <&gpx3 7 GPIO_ACTIVE_HIGH>;
 458         pinctrl-names = "default";
 459         pinctrl-0 = <&hdmi_hpd>;
 460         vdd-supply = <&ldo3_reg>;
 461         vdd_osc-supply = <&ldo4_reg>;
 462         vdd_pll-supply = <&ldo3_reg>;
 463         ddc = <&i2c_5>;
 464         status = "okay";
 465
 466         ports {
 467                 #address-cells = <1>;
 468                 #size-cells = <0>;
 469
 470                 port@1 {
 471                         reg = <1>;
 472                         hdmi_to_mhl: endpoint {
 473                                 remote-endpoint = <&mhl_to_hdmi>;
 474                         };
 475                 };
 476         };
 477 };
 478
 479 &hsotg {
 480         vusb_d-supply = <&ldo15_reg>;
 481         vusb_a-supply = <&ldo12_reg>;
 482         dr_mode = "peripheral";
 483         status = "okay";
 484 };
 485
 486 &i2c_0 {
 487         samsung,i2c-sda-delay = <100>;
 488         samsung,i2c-slave-addr = <0x10>;
 489         samsung,i2c-max-bus-freq = <400000>;
 490         pinctrl-0 = <&i2c0_bus>;
 491         pinctrl-names = "default";
 492         status = "okay";
 493
 494         s5c73m3: s5c73m3@3c {
 495                 compatible = "samsung,s5c73m3";
 496                 reg = <0x3c>;
 497                 xshutdown-gpios = <&gpf1 3 GPIO_ACTIVE_LOW>; /* ISP_RESET */
 498                 vdd-int-supply = <&buck9_reg>;
 499                 vddio-cis-supply = <&ldo9_reg>;
 500                 vddio-host-supply = <&ldo18_reg>;
 501                 vdd-af-supply = <&cam_af_reg>;
 502                 vdd-reg-supply = <&cam_io_reg>;
 503                 clock-frequency = <24000000>;
 504                 /* CAM_A_CLKOUT */
 505                 clocks = <&camera 0>;
 506                 clock-names = "cis_extclk";
 507                 status = "disabled";
 508                 port {
 509                         s5c73m3_ep: endpoint {
 510                                 remote-endpoint = <&csis0_ep>;
 511                                 data-lanes = <1 2 3 4>;
 512                         };
 513                 };
 514         };
 515 };
 516
 517 &i2c1_isp {
 518         pinctrl-0 = <&fimc_is_i2c1>;
 519         pinctrl-names = "default";
 520
 521         s5k6a3@10 {
 522                 compatible = "samsung,s5k6a3";
 523                 reg = <0x10>;
 524                 svdda-supply = <&cam_io_reg>;
 525                 svddio-supply = <&ldo19_reg>;
 526                 afvdd-supply = <&ldo19_reg>;
 527                 clock-frequency = <24000000>;
 528                 /* CAM_B_CLKOUT */
 529                 clocks = <&camera 1>;
 530                 clock-names = "extclk";
 531                 samsung,camclk-out = <1>;
 532                 gpios = <&gpm1 6 GPIO_ACTIVE_HIGH>;
 533
 534                 port {
 535                         is_s5k6a3_ep: endpoint {
 536                                 remote-endpoint = <&csis1_ep>;
 537                                 data-lanes = <1>;
 538                         };
 539                 };
 540         };
 541 };
 542
 543 &i2c_3 {
 544         samsung,i2c-sda-delay = <100>;
 545         samsung,i2c-slave-addr = <0x10>;
 546         samsung,i2c-max-bus-freq = <400000>;
 547         pinctrl-0 = <&i2c3_bus>;
 548         pinctrl-names = "default";
 549         status = "okay";
 550 };
 551
 552 &i2c_4 {
 553         samsung,i2c-sda-delay = <100>;
 554         samsung,i2c-slave-addr = <0x10>;
 555         samsung,i2c-max-bus-freq = <100000>;
 556         pinctrl-0 = <&i2c4_bus>;
 557         pinctrl-names = "default";
 558         status = "okay";
 559
 560         wm1811: wm1811@1a {
 561                 compatible = "wlf,wm1811";
 562                 reg = <0x1a>;
 563                 clocks = <&pmu_system_controller 0>;
 564                 clock-names = "MCLK1";
 565                 DCVDD-supply = <&ldo3_reg>;
 566                 DBVDD1-supply = <&ldo3_reg>;
 567                 wlf,ldo1ena = <&gpj0 4 0>;
 568         };
 569 };
 570
 571 &i2c_5 {
 572         status = "okay";
 573 };
 574
 575 &i2c_7 {
 576         samsung,i2c-sda-delay = <100>;
 577         samsung,i2c-slave-addr = <0x10>;
 578         samsung,i2c-max-bus-freq = <100000>;
 579         pinctrl-0 = <&i2c7_bus>;
 580         pinctrl-names = "default";
 581         status = "okay";
 582
 583         max77686: max77686_pmic@9 {
 584                 compatible = "maxim,max77686";
 585                 interrupt-parent = <&gpx0>;
 586                 interrupts = <7 IRQ_TYPE_NONE>;
 587                 pinctrl-0 = <&max77686_irq>;
 588                 pinctrl-names = "default";
 589                 reg = <0x09>;
 590                 #clock-cells = <1>;
 591
 592                 voltage-regulators {
 593                         ldo1_reg: LDO1 {
 594                                 regulator-name = "VALIVE_1.0V_AP";
 595                                 regulator-min-microvolt = <1000000>;
 596                                 regulator-max-microvolt = <1000000>;
 597                                 regulator-always-on;
 598                         };
 599
 600                         ldo2_reg: LDO2 {
 601                                 regulator-name = "VM1M2_1.2V_AP";
 602                                 regulator-min-microvolt = <1200000>;
 603                                 regulator-max-microvolt = <1200000>;
 604                                 regulator-always-on;
 605                                 regulator-state-mem {
 606                                         regulator-on-in-suspend;
 607                                 };
 608                         };
 609
 610                         ldo3_reg: LDO3 {
 611                                 regulator-name = "VCC_1.8V_AP";
 612                                 regulator-min-microvolt = <1800000>;
 613                                 regulator-max-microvolt = <1800000>;
 614                                 regulator-always-on;
 615                         };
 616
 617                         ldo4_reg: LDO4 {
 618                                 regulator-name = "VCC_2.8V_AP";
 619                                 regulator-min-microvolt = <2800000>;
 620                                 regulator-max-microvolt = <2800000>;
 621                                 regulator-always-on;
 622                         };
 623
 624                         ldo5_reg: LDO5 {
 625                                 regulator-name = "VCC_1.8V_IO";
 626                                 regulator-min-microvolt = <1800000>;
 627                                 regulator-max-microvolt = <1800000>;
 628                                 regulator-always-on;
 629                         };
 630
 631                         ldo6_reg: LDO6 {
 632                                 regulator-name = "VMPLL_1.0V_AP";
 633                                 regulator-min-microvolt = <1000000>;
 634                                 regulator-max-microvolt = <1000000>;
 635                                 regulator-always-on;
 636                                 regulator-state-mem {
 637                                         regulator-on-in-suspend;
 638                                 };
 639                         };
 640
 641                         ldo7_reg: LDO7 {
 642                                 regulator-name = "VPLL_1.0V_AP";
 643                                 regulator-min-microvolt = <1000000>;
 644                                 regulator-max-microvolt = <1000000>;
 645                                 regulator-always-on;
 646                                 regulator-state-mem {
 647                                         regulator-on-in-suspend;
 648                                 };
 649                         };
 650
 651                         ldo8_reg: LDO8 {
 652                                 regulator-name = "VMIPI_1.0V";
 653                                 regulator-min-microvolt = <1000000>;
 654                                 regulator-max-microvolt = <1000000>;
 655                                 regulator-state-mem {
 656                                         regulator-off-in-suspend;
 657                                 };
 658                         };
 659
 660                         ldo9_reg: LDO9 {
 661                                 regulator-name = "CAM_ISP_MIPI_1.2V";
 662                                 regulator-min-microvolt = <1200000>;
 663                                 regulator-max-microvolt = <1200000>;
 664                         };
 665
 666                         ldo10_reg: LDO10 {
 667                                 regulator-name = "VMIPI_1.8V";
 668                                 regulator-min-microvolt = <1800000>;
 669                                 regulator-max-microvolt = <1800000>;
 670                                 regulator-state-mem {
 671                                         regulator-off-in-suspend;
 672                                 };
 673                         };
 674
 675                         ldo11_reg: LDO11 {
 676                                 regulator-name = "VABB1_1.95V";
 677                                 regulator-min-microvolt = <1950000>;
 678                                 regulator-max-microvolt = <1950000>;
 679                                 regulator-always-on;
 680                                 regulator-state-mem {
 681                                         regulator-off-in-suspend;
 682                                 };
 683                         };
 684
 685                         ldo12_reg: LDO12 {
 686                                 regulator-name = "VUOTG_3.0V";
 687                                 regulator-min-microvolt = <3000000>;
 688                                 regulator-max-microvolt = <3000000>;
 689                                 regulator-state-mem {
 690                                         regulator-off-in-suspend;
 691                                 };
 692                         };
 693
 694                         ldo13_reg: LDO13 {
 695                                 regulator-name = "NFC_AVDD_1.8V";
 696                                 regulator-min-microvolt = <1800000>;
 697                                 regulator-max-microvolt = <1800000>;
 698                         };
 699
 700                         ldo14_reg: LDO14 {
 701                                 regulator-name = "VABB2_1.95V";
 702                                 regulator-min-microvolt = <1950000>;
 703                                 regulator-max-microvolt = <1950000>;
 704                                 regulator-always-on;
 705                                 regulator-state-mem {
 706                                         regulator-off-in-suspend;
 707                                 };
 708                         };
 709
 710                         ldo15_reg: LDO15 {
 711                                 regulator-name = "VHSIC_1.0V";
 712                                 regulator-min-microvolt = <1000000>;
 713                                 regulator-max-microvolt = <1000000>;
 714                                 regulator-state-mem {
 715                                         regulator-on-in-suspend;
 716                                 };
 717                         };
 718
 719                         ldo16_reg: LDO16 {
 720                                 regulator-name = "VHSIC_1.8V";
 721                                 regulator-min-microvolt = <1800000>;
 722                                 regulator-max-microvolt = <1800000>;
 723                                 regulator-state-mem {
 724                                         regulator-on-in-suspend;
 725                                 };
 726                         };
 727
 728                         ldo17_reg: LDO17 {
 729                                 regulator-name = "CAM_SENSOR_CORE_1.2V";
 730                                 regulator-min-microvolt = <1200000>;
 731                                 regulator-max-microvolt = <1200000>;
 732                         };
 733
 734                         ldo18_reg: LDO18 {
 735                                 regulator-name = "CAM_ISP_SEN_IO_1.8V";
 736                                 regulator-min-microvolt = <1800000>;
 737                                 regulator-max-microvolt = <1800000>;
 738                         };
 739
 740                         ldo19_reg: LDO19 {
 741                                 regulator-name = "VT_CAM_1.8V";
 742                                 regulator-min-microvolt = <1800000>;
 743                                 regulator-max-microvolt = <1800000>;
 744                         };
 745
 746                         ldo20_reg: LDO20 {
 747                                 regulator-name = "VDDQ_PRE_1.8V";
 748                                 regulator-min-microvolt = <1800000>;
 749                                 regulator-max-microvolt = <1800000>;
 750                         };
 751
 752                         ldo21_reg: LDO21 {
 753                                 regulator-name = "VTF_2.8V";
 754                                 regulator-min-microvolt = <2800000>;
 755                                 regulator-max-microvolt = <2800000>;
 756                                 maxim,ena-gpios = <&gpy2 0 GPIO_ACTIVE_HIGH>;
 757                         };
 758
 759                         ldo22_reg: LDO22 {
 760                                 regulator-name = "VMEM_VDD_2.8V";
 761                                 regulator-min-microvolt = <2800000>;
 762                                 regulator-max-microvolt = <2800000>;
 763                                 maxim,ena-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>;
 764                         };
 765
 766                         ldo23_reg: LDO23 {
 767                                 regulator-name = "TSP_AVDD_3.3V";
 768                                 regulator-min-microvolt = <3300000>;
 769                                 regulator-max-microvolt = <3300000>;
 770                         };
 771
 772                         ldo24_reg: LDO24 {
 773                                 regulator-name = "TSP_VDD_1.8V";
 774                                 regulator-min-microvolt = <1800000>;
 775                                 regulator-max-microvolt = <1800000>;
 776                         };
 777
 778                         ldo25_reg: LDO25 {
 779                                 regulator-name = "LDO25";
 780                         };
 781
 782                         ldo26_reg: LDO26 {
 783                                 regulator-name = "MOTOR_VCC_3.0V";
 784                                 regulator-min-microvolt = <3000000>;
 785                                 regulator-max-microvolt = <3000000>;
 786                         };
 787
 788                         buck1_reg: BUCK1 {
 789                                 regulator-name = "vdd_mif";
 790                                 regulator-min-microvolt = <850000>;
 791                                 regulator-max-microvolt = <1100000>;
 792                                 regulator-always-on;
 793                                 regulator-boot-on;
 794                                 regulator-state-mem {
 795                                         regulator-off-in-suspend;
 796                                 };
 797                         };
 798
 799                         buck2_reg: BUCK2 {
 800                                 regulator-name = "vdd_arm";
 801                                 regulator-min-microvolt = <850000>;
 802                                 regulator-max-microvolt = <1500000>;
 803                                 regulator-always-on;
 804                                 regulator-boot-on;
 805                                 regulator-state-mem {
 806                                         regulator-on-in-suspend;
 807                                 };
 808                         };
 809
 810                         buck3_reg: BUCK3 {
 811                                 regulator-name = "vdd_int";
 812                                 regulator-min-microvolt = <850000>;
 813                                 regulator-max-microvolt = <1150000>;
 814                                 regulator-always-on;
 815                                 regulator-boot-on;
 816                                 regulator-state-mem {
 817                                         regulator-off-in-suspend;
 818                                 };
 819                         };
 820
 821                         buck4_reg: BUCK4 {
 822                                 regulator-name = "vdd_g3d";
 823                                 regulator-min-microvolt = <850000>;
 824                                 regulator-max-microvolt = <1150000>;
 825                                 regulator-boot-on;
 826                                 regulator-state-mem {
 827                                         regulator-off-in-suspend;
 828                                 };
 829                         };
 830
 831                         buck5_reg: BUCK5 {
 832                                 regulator-name = "VMEM_1.2V_AP";
 833                                 regulator-min-microvolt = <1200000>;
 834                                 regulator-max-microvolt = <1200000>;
 835                                 regulator-always-on;
 836                         };
 837
 838                         buck6_reg: BUCK6 {
 839                                 regulator-name = "VCC_SUB_1.35V";
 840                                 regulator-min-microvolt = <1350000>;
 841                                 regulator-max-microvolt = <1350000>;
 842                                 regulator-always-on;
 843                         };
 844
 845                         buck7_reg: BUCK7 {
 846                                 regulator-name = "VCC_SUB_2.0V";
 847                                 regulator-min-microvolt = <2000000>;
 848                                 regulator-max-microvolt = <2000000>;
 849                                 regulator-always-on;
 850                         };
 851
 852                         buck8_reg: BUCK8 {
 853                                 regulator-name = "VMEM_VDDF_3.0V";
 854                                 regulator-min-microvolt = <2850000>;
 855                                 regulator-max-microvolt = <2850000>;
 856                                 maxim,ena-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>;
 857                         };
 858
 859                         buck9_reg: BUCK9 {
 860                                 regulator-name = "CAM_ISP_CORE_1.2V";
 861                                 regulator-min-microvolt = <1000000>;
 862                                 regulator-max-microvolt = <1200000>;
 863                         };
 864                 };
 865         };
 866 };
 867
 868 &i2c_8 {
 869         status = "okay";
 870 };
 871
 872 &i2s0 {
 873         pinctrl-0 = <&i2s0_bus>;
 874         pinctrl-names = "default";
 875         status = "okay";
 876 };
 877
 878 &mixer {
 879         status = "okay";
 880 };
 881
 882 &mshc_0 {
 883         broken-cd;
 884         non-removable;
 885         card-detect-delay = <200>;
 886         vmmc-supply = <&ldo22_reg>;
 887         clock-frequency = <400000000>;
 888         samsung,dw-mshc-ciu-div = <0>;
 889         samsung,dw-mshc-sdr-timing = <2 3>;
 890         samsung,dw-mshc-ddr-timing = <1 2>;
 891         pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
 892         pinctrl-names = "default";
 893         status = "okay";
 894         bus-width = <8>;
 895         cap-mmc-highspeed;
 896 };
 897
 898 &pmu_system_controller {
 899         assigned-clocks = <&pmu_system_controller 0>;
 900         assigned-clock-parents =  <&clock CLK_XUSBXTI>;
 901 };
 902
 903 &pinctrl_0 {
 904         pinctrl-names = "default";
 905         pinctrl-0 = <&sleep0>;
 906
 907         mhl_int: mhl-int {
 908                 samsung,pins = "gpf3-5";
 909                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 910         };
 911
 912         i2c_mhl_bus: i2c-mhl-bus {
 913                 samsung,pins = "gpf0-4", "gpf0-6";
 914                 samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 915                 samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 916                 samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 917         };
 918
 919         sleep0: sleep-states {
 920                 PIN_SLP(gpa0-0, INPUT, NONE);
 921                 PIN_SLP(gpa0-1, OUT0, NONE);
 922                 PIN_SLP(gpa0-2, INPUT, NONE);
 923                 PIN_SLP(gpa0-3, INPUT, UP);
 924                 PIN_SLP(gpa0-4, INPUT, NONE);
 925                 PIN_SLP(gpa0-5, INPUT, DOWN);
 926                 PIN_SLP(gpa0-6, INPUT, DOWN);
 927                 PIN_SLP(gpa0-7, INPUT, UP);
 928
 929                 PIN_SLP(gpa1-0, INPUT, DOWN);
 930                 PIN_SLP(gpa1-1, INPUT, DOWN);
 931                 PIN_SLP(gpa1-2, INPUT, DOWN);
 932                 PIN_SLP(gpa1-3, INPUT, DOWN);
 933                 PIN_SLP(gpa1-4, INPUT, DOWN);
 934                 PIN_SLP(gpa1-5, INPUT, DOWN);
 935
 936                 PIN_SLP(gpb-0, INPUT, NONE);
 937                 PIN_SLP(gpb-1, INPUT, NONE);
 938                 PIN_SLP(gpb-2, INPUT, NONE);
 939                 PIN_SLP(gpb-3, INPUT, NONE);
 940                 PIN_SLP(gpb-4, INPUT, DOWN);
 941                 PIN_SLP(gpb-5, INPUT, UP);
 942                 PIN_SLP(gpb-6, INPUT, DOWN);
 943                 PIN_SLP(gpb-7, INPUT, DOWN);
 944
 945                 PIN_SLP(gpc0-0, INPUT, DOWN);
 946                 PIN_SLP(gpc0-1, INPUT, DOWN);
 947                 PIN_SLP(gpc0-2, INPUT, DOWN);
 948                 PIN_SLP(gpc0-3, INPUT, DOWN);
 949                 PIN_SLP(gpc0-4, INPUT, DOWN);
 950
 951                 PIN_SLP(gpc1-0, INPUT, NONE);
 952                 PIN_SLP(gpc1-1, PREV, NONE);
 953                 PIN_SLP(gpc1-2, INPUT, NONE);
 954                 PIN_SLP(gpc1-3, INPUT, NONE);
 955                 PIN_SLP(gpc1-4, INPUT, NONE);
 956
 957                 PIN_SLP(gpd0-0, INPUT, DOWN);
 958                 PIN_SLP(gpd0-1, INPUT, DOWN);
 959                 PIN_SLP(gpd0-2, INPUT, NONE);
 960                 PIN_SLP(gpd0-3, INPUT, NONE);
 961
 962                 PIN_SLP(gpd1-0, INPUT, DOWN);
 963                 PIN_SLP(gpd1-1, INPUT, DOWN);
 964                 PIN_SLP(gpd1-2, INPUT, NONE);
 965                 PIN_SLP(gpd1-3, INPUT, NONE);
 966
 967                 PIN_SLP(gpf0-0, INPUT, NONE);
 968                 PIN_SLP(gpf0-1, INPUT, NONE);
 969                 PIN_SLP(gpf0-2, INPUT, DOWN);
 970                 PIN_SLP(gpf0-3, INPUT, DOWN);
 971                 PIN_SLP(gpf0-4, INPUT, NONE);
 972                 PIN_SLP(gpf0-5, INPUT, DOWN);
 973                 PIN_SLP(gpf0-6, INPUT, NONE);
 974                 PIN_SLP(gpf0-7, INPUT, DOWN);
 975
 976                 PIN_SLP(gpf1-0, INPUT, DOWN);
 977                 PIN_SLP(gpf1-1, INPUT, DOWN);
 978                 PIN_SLP(gpf1-2, INPUT, DOWN);
 979                 PIN_SLP(gpf1-3, INPUT, DOWN);
 980                 PIN_SLP(gpf1-4, INPUT, NONE);
 981                 PIN_SLP(gpf1-5, INPUT, NONE);
 982                 PIN_SLP(gpf1-6, INPUT, DOWN);
 983                 PIN_SLP(gpf1-7, PREV, NONE);
 984
 985                 PIN_SLP(gpf2-0, PREV, NONE);
 986                 PIN_SLP(gpf2-1, INPUT, DOWN);
 987                 PIN_SLP(gpf2-2, INPUT, DOWN);
 988                 PIN_SLP(gpf2-3, INPUT, DOWN);
 989                 PIN_SLP(gpf2-4, INPUT, DOWN);
 990                 PIN_SLP(gpf2-5, INPUT, DOWN);
 991                 PIN_SLP(gpf2-6, INPUT, NONE);
 992                 PIN_SLP(gpf2-7, INPUT, NONE);
 993
 994                 PIN_SLP(gpf3-0, INPUT, NONE);
 995                 PIN_SLP(gpf3-1, PREV, NONE);
 996                 PIN_SLP(gpf3-2, PREV, NONE);
 997                 PIN_SLP(gpf3-3, PREV, NONE);
 998                 PIN_SLP(gpf3-4, OUT1, NONE);
 999                 PIN_SLP(gpf3-5, INPUT, DOWN);
1000
1001                 PIN_SLP(gpj0-0, PREV, NONE);
1002                 PIN_SLP(gpj0-1, PREV, NONE);
1003                 PIN_SLP(gpj0-2, PREV, NONE);
1004                 PIN_SLP(gpj0-3, INPUT, DOWN);
1005                 PIN_SLP(gpj0-4, PREV, NONE);
1006                 PIN_SLP(gpj0-5, PREV, NONE);
1007                 PIN_SLP(gpj0-6, INPUT, DOWN);
1008                 PIN_SLP(gpj0-7, INPUT, DOWN);
1009
1010                 PIN_SLP(gpj1-0, INPUT, DOWN);
1011                 PIN_SLP(gpj1-1, PREV, NONE);
1012                 PIN_SLP(gpj1-2, PREV, NONE);
1013                 PIN_SLP(gpj1-3, INPUT, DOWN);
1014                 PIN_SLP(gpj1-4, INPUT, DOWN);
1015         };
1016 };
1017
1018 &pinctrl_1 {
1019         pinctrl-names = "default";
1020         pinctrl-0 = <&sleep1>;
1021
1022         gpio_keys: gpio-keys {
1023                 samsung,pins = "gpx0-1", "gpx2-2", "gpx2-7", "gpx3-3";
1024                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
1025         };
1026
1027         max77686_irq: max77686-irq {
1028                 samsung,pins = "gpx0-7";
1029                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
1030         };
1031
1032         max77693_irq: max77693-irq {
1033                 samsung,pins = "gpx1-5";
1034                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
1035         };
1036
1037         max77693_fuel_irq: max77693-fuel-irq {
1038                 samsung,pins = "gpx2-3";
1039                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
1040         };
1041
1042         sdhci2_cd: sdhci2-cd-irq {
1043                 samsung,pins = "gpx3-4";
1044                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
1045         };
1046
1047         hdmi_hpd: hdmi-hpd {
1048                 samsung,pins = "gpx3-7";
1049                 samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
1050         };
1051
1052         sleep1: sleep-states {
1053                 PIN_SLP(gpk0-0, PREV, NONE);
1054                 PIN_SLP(gpk0-1, PREV, NONE);
1055                 PIN_SLP(gpk0-2, OUT0, NONE);
1056                 PIN_SLP(gpk0-3, PREV, NONE);
1057                 PIN_SLP(gpk0-4, PREV, NONE);
1058                 PIN_SLP(gpk0-5, PREV, NONE);
1059                 PIN_SLP(gpk0-6, PREV, NONE);
1060
1061                 PIN_SLP(gpk1-0, INPUT, DOWN);
1062                 PIN_SLP(gpk1-1, INPUT, DOWN);
1063                 PIN_SLP(gpk1-2, INPUT, DOWN);
1064                 PIN_SLP(gpk1-3, PREV, NONE);
1065                 PIN_SLP(gpk1-4, PREV, NONE);
1066                 PIN_SLP(gpk1-5, PREV, NONE);
1067                 PIN_SLP(gpk1-6, PREV, NONE);
1068
1069                 PIN_SLP(gpk2-0, INPUT, DOWN);
1070                 PIN_SLP(gpk2-1, INPUT, DOWN);
1071                 PIN_SLP(gpk2-2, INPUT, DOWN);
1072                 PIN_SLP(gpk2-3, INPUT, DOWN);
1073                 PIN_SLP(gpk2-4, INPUT, DOWN);
1074                 PIN_SLP(gpk2-5, INPUT, DOWN);
1075                 PIN_SLP(gpk2-6, INPUT, DOWN);
1076
1077                 PIN_SLP(gpk3-0, OUT0, NONE);
1078                 PIN_SLP(gpk3-1, INPUT, NONE);
1079                 PIN_SLP(gpk3-2, INPUT, DOWN);
1080                 PIN_SLP(gpk3-3, INPUT, NONE);
1081                 PIN_SLP(gpk3-4, INPUT, NONE);
1082                 PIN_SLP(gpk3-5, INPUT, NONE);
1083                 PIN_SLP(gpk3-6, INPUT, NONE);
1084
1085                 PIN_SLP(gpl0-0, INPUT, DOWN);
1086                 PIN_SLP(gpl0-1, INPUT, DOWN);
1087                 PIN_SLP(gpl0-2, INPUT, DOWN);
1088                 PIN_SLP(gpl0-3, INPUT, DOWN);
1089                 PIN_SLP(gpl0-4, PREV, NONE);
1090                 PIN_SLP(gpl0-6, PREV, NONE);
1091
1092                 PIN_SLP(gpl1-0, INPUT, DOWN);
1093                 PIN_SLP(gpl1-1, INPUT, DOWN);
1094                 PIN_SLP(gpl2-0, INPUT, DOWN);
1095                 PIN_SLP(gpl2-1, INPUT, DOWN);
1096                 PIN_SLP(gpl2-2, INPUT, DOWN);
1097                 PIN_SLP(gpl2-3, INPUT, DOWN);
1098                 PIN_SLP(gpl2-4, INPUT, DOWN);
1099                 PIN_SLP(gpl2-5, INPUT, DOWN);
1100                 PIN_SLP(gpl2-6, PREV, NONE);
1101                 PIN_SLP(gpl2-7, INPUT, DOWN);
1102
1103                 PIN_SLP(gpm0-0, INPUT, DOWN);
1104                 PIN_SLP(gpm0-1, INPUT, DOWN);
1105                 PIN_SLP(gpm0-2, INPUT, DOWN);
1106                 PIN_SLP(gpm0-3, INPUT, DOWN);
1107                 PIN_SLP(gpm0-4, INPUT, DOWN);
1108                 PIN_SLP(gpm0-5, INPUT, DOWN);
1109                 PIN_SLP(gpm0-6, INPUT, DOWN);
1110                 PIN_SLP(gpm0-7, INPUT, DOWN);
1111
1112                 PIN_SLP(gpm1-0, INPUT, DOWN);
1113                 PIN_SLP(gpm1-1, INPUT, DOWN);
1114                 PIN_SLP(gpm1-2, INPUT, NONE);
1115                 PIN_SLP(gpm1-3, INPUT, NONE);
1116                 PIN_SLP(gpm1-4, INPUT, NONE);
1117                 PIN_SLP(gpm1-5, INPUT, NONE);
1118                 PIN_SLP(gpm1-6, INPUT, DOWN);
1119
1120                 PIN_SLP(gpm2-0, INPUT, NONE);
1121                 PIN_SLP(gpm2-1, INPUT, NONE);
1122                 PIN_SLP(gpm2-2, INPUT, DOWN);
1123                 PIN_SLP(gpm2-3, INPUT, DOWN);
1124                 PIN_SLP(gpm2-4, INPUT, DOWN);
1125
1126                 PIN_SLP(gpm3-0, PREV, NONE);
1127                 PIN_SLP(gpm3-1, PREV, NONE);
1128                 PIN_SLP(gpm3-2, PREV, NONE);
1129                 PIN_SLP(gpm3-3, OUT1, NONE);
1130                 PIN_SLP(gpm3-4, INPUT, DOWN);
1131                 PIN_SLP(gpm3-5, INPUT, DOWN);
1132                 PIN_SLP(gpm3-6, INPUT, DOWN);
1133                 PIN_SLP(gpm3-7, INPUT, DOWN);
1134
1135                 PIN_SLP(gpm4-0, INPUT, DOWN);
1136                 PIN_SLP(gpm4-1, INPUT, DOWN);
1137                 PIN_SLP(gpm4-2, INPUT, DOWN);
1138                 PIN_SLP(gpm4-3, INPUT, DOWN);
1139                 PIN_SLP(gpm4-4, INPUT, DOWN);
1140                 PIN_SLP(gpm4-5, INPUT, DOWN);
1141                 PIN_SLP(gpm4-6, INPUT, DOWN);
1142                 PIN_SLP(gpm4-7, INPUT, DOWN);
1143
1144                 PIN_SLP(gpy0-0, INPUT, DOWN);
1145                 PIN_SLP(gpy0-1, INPUT, DOWN);
1146                 PIN_SLP(gpy0-2, INPUT, DOWN);
1147                 PIN_SLP(gpy0-3, INPUT, DOWN);
1148                 PIN_SLP(gpy0-4, INPUT, DOWN);
1149                 PIN_SLP(gpy0-5, INPUT, DOWN);
1150
1151                 PIN_SLP(gpy1-0, INPUT, DOWN);
1152                 PIN_SLP(gpy1-1, INPUT, DOWN);
1153                 PIN_SLP(gpy1-2, INPUT, DOWN);
1154                 PIN_SLP(gpy1-3, INPUT, DOWN);
1155
1156                 PIN_SLP(gpy2-0, PREV, NONE);
1157                 PIN_SLP(gpy2-1, INPUT, DOWN);
1158                 PIN_SLP(gpy2-2, INPUT, NONE);
1159                 PIN_SLP(gpy2-3, INPUT, NONE);
1160                 PIN_SLP(gpy2-4, INPUT, NONE);
1161                 PIN_SLP(gpy2-5, INPUT, NONE);
1162
1163                 PIN_SLP(gpy3-0, INPUT, DOWN);
1164                 PIN_SLP(gpy3-1, INPUT, DOWN);
1165                 PIN_SLP(gpy3-2, INPUT, DOWN);
1166                 PIN_SLP(gpy3-3, INPUT, DOWN);
1167                 PIN_SLP(gpy3-4, INPUT, DOWN);
1168                 PIN_SLP(gpy3-5, INPUT, DOWN);
1169                 PIN_SLP(gpy3-6, INPUT, DOWN);
1170                 PIN_SLP(gpy3-7, INPUT, DOWN);
1171
1172                 PIN_SLP(gpy4-0, INPUT, DOWN);
1173                 PIN_SLP(gpy4-1, INPUT, DOWN);
1174                 PIN_SLP(gpy4-2, INPUT, DOWN);
1175                 PIN_SLP(gpy4-3, INPUT, DOWN);
1176                 PIN_SLP(gpy4-4, INPUT, DOWN);
1177                 PIN_SLP(gpy4-5, INPUT, DOWN);
1178                 PIN_SLP(gpy4-6, INPUT, DOWN);
1179                 PIN_SLP(gpy4-7, INPUT, DOWN);
1180
1181                 PIN_SLP(gpy5-0, INPUT, DOWN);
1182                 PIN_SLP(gpy5-1, INPUT, DOWN);
1183                 PIN_SLP(gpy5-2, INPUT, DOWN);
1184                 PIN_SLP(gpy5-3, INPUT, DOWN);
1185                 PIN_SLP(gpy5-4, INPUT, DOWN);
1186                 PIN_SLP(gpy5-5, INPUT, DOWN);
1187                 PIN_SLP(gpy5-6, INPUT, DOWN);
1188                 PIN_SLP(gpy5-7, INPUT, DOWN);
1189
1190                 PIN_SLP(gpy6-0, INPUT, DOWN);
1191                 PIN_SLP(gpy6-1, INPUT, DOWN);
1192                 PIN_SLP(gpy6-2, INPUT, DOWN);
1193                 PIN_SLP(gpy6-3, INPUT, DOWN);
1194                 PIN_SLP(gpy6-4, INPUT, DOWN);
1195                 PIN_SLP(gpy6-5, INPUT, DOWN);
1196                 PIN_SLP(gpy6-6, INPUT, DOWN);
1197                 PIN_SLP(gpy6-7, INPUT, DOWN);
1198         };
1199 };
1200
1201 &pinctrl_2 {
1202         pinctrl-names = "default";
1203         pinctrl-0 = <&sleep2>;
1204
1205         sleep2: sleep-states {
1206                 PIN_SLP(gpz-0, INPUT, DOWN);
1207                 PIN_SLP(gpz-1, INPUT, DOWN);
1208                 PIN_SLP(gpz-2, INPUT, DOWN);
1209                 PIN_SLP(gpz-3, INPUT, DOWN);
1210                 PIN_SLP(gpz-4, INPUT, DOWN);
1211                 PIN_SLP(gpz-5, INPUT, DOWN);
1212                 PIN_SLP(gpz-6, INPUT, DOWN);
1213         };
1214 };
1215
1216 &pinctrl_3 {
1217         pinctrl-names = "default";
1218         pinctrl-0 = <&sleep3>;
1219
1220         sleep3: sleep-states {
1221                 PIN_SLP(gpv0-0, INPUT, DOWN);
1222                 PIN_SLP(gpv0-1, INPUT, DOWN);
1223                 PIN_SLP(gpv0-2, INPUT, DOWN);
1224                 PIN_SLP(gpv0-3, INPUT, DOWN);
1225                 PIN_SLP(gpv0-4, INPUT, DOWN);
1226                 PIN_SLP(gpv0-5, INPUT, DOWN);
1227                 PIN_SLP(gpv0-6, INPUT, DOWN);
1228                 PIN_SLP(gpv0-7, INPUT, DOWN);
1229
1230                 PIN_SLP(gpv1-0, INPUT, DOWN);
1231                 PIN_SLP(gpv1-1, INPUT, DOWN);
1232                 PIN_SLP(gpv1-2, INPUT, DOWN);
1233                 PIN_SLP(gpv1-3, INPUT, DOWN);
1234                 PIN_SLP(gpv1-4, INPUT, DOWN);
1235                 PIN_SLP(gpv1-5, INPUT, DOWN);
1236                 PIN_SLP(gpv1-6, INPUT, DOWN);
1237                 PIN_SLP(gpv1-7, INPUT, DOWN);
1238
1239                 PIN_SLP(gpv2-0, INPUT, DOWN);
1240                 PIN_SLP(gpv2-1, INPUT, DOWN);
1241                 PIN_SLP(gpv2-2, INPUT, DOWN);
1242                 PIN_SLP(gpv2-3, INPUT, DOWN);
1243                 PIN_SLP(gpv2-4, INPUT, DOWN);
1244                 PIN_SLP(gpv2-5, INPUT, DOWN);
1245                 PIN_SLP(gpv2-6, INPUT, DOWN);
1246                 PIN_SLP(gpv2-7, INPUT, DOWN);
1247
1248                 PIN_SLP(gpv3-0, INPUT, DOWN);
1249                 PIN_SLP(gpv3-1, INPUT, DOWN);
1250                 PIN_SLP(gpv3-2, INPUT, DOWN);
1251                 PIN_SLP(gpv3-3, INPUT, DOWN);
1252                 PIN_SLP(gpv3-4, INPUT, DOWN);
1253                 PIN_SLP(gpv3-5, INPUT, DOWN);
1254                 PIN_SLP(gpv3-6, INPUT, DOWN);
1255                 PIN_SLP(gpv3-7, INPUT, DOWN);
1256
1257                 PIN_SLP(gpv4-0, INPUT, DOWN);
1258         };
1259 };
1260
1261 &pwm {
1262         pinctrl-0 = <&pwm0_out>;
1263         pinctrl-names = "default";
1264         samsung,pwm-outputs = <0>;
1265         status = "okay";
1266 };
1267
1268 &rtc {
1269         status = "okay";
1270         clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>;
1271         clock-names = "rtc", "rtc_src";
1272 };
1273
1274 &sdhci_2 {
1275         bus-width = <4>;
1276         cd-gpios = <&gpx3 4 GPIO_ACTIVE_LOW>;
1277         pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sdhci2_cd>;
1278         pinctrl-names = "default";
1279         vmmc-supply = <&ldo21_reg>;
1280         status = "okay";
1281 };
1282
1283 &sdhci_3 {
1284         #address-cells = <1>;
1285         #size-cells = <0>;
1286         non-removable;
1287         bus-width = <4>;
1288
1289         mmc-pwrseq = <&wlan_pwrseq>;
1290         pinctrl-names = "default";
1291         pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4>;
1292         status = "okay";
1293
1294         brcmf: wifi@1 {
1295                 reg = <1>;
1296                 compatible = "brcm,bcm4329-fmac";
1297                 interrupt-parent = <&gpx2>;
1298                 interrupts = <5 IRQ_TYPE_NONE>;
1299                 interrupt-names = "host-wake";
1300         };
1301 };
1302
1303 &serial_0 {
1304         status = "okay";
1305 };
1306
1307 &serial_1 {
1308         status = "okay";
1309 };
1310
1311 &serial_2 {
1312         status = "okay";
1313 };
1314
1315 &serial_3 {
1316         status = "okay";
1317 };
1318
1319 &spi_1 {
1320         pinctrl-names = "default";
1321         pinctrl-0 = <&spi1_bus>;
1322         cs-gpios = <&gpb 5 GPIO_ACTIVE_HIGH>;
1323         status = "okay";
1324
1325         s5c73m3_spi: s5c73m3@0 {
1326                 compatible = "samsung,s5c73m3";
1327                 spi-max-frequency = <50000000>;
1328                 reg = <0>;
1329                 controller-data {
1330                         samsung,spi-feedback-delay = <2>;
1331                 };
1332         };
1333 };
1334
1335 &tmu {
1336         vtmu-supply = <&ldo10_reg>;
1337         status = "okay";
1338 };