arch/arm/boot/dts/omap3-overo-base.dtsi

   1 /*
   2  * Copyright (C) 2012 Florian Vaussard, EPFL Mobots group
   3  *
   4  * This program is free software; you can redistribute it and/or modify
   5  * it under the terms of the GNU General Public License version 2 as
   6  * published by the Free Software Foundation.
   7  */
   8
   9 /*
  10  * The Gumstix Overo must be combined with an expansion board.
  11  */
  12
  13 / {
  14         pwmleds {
  15                 compatible = "pwm-leds";
  16
  17                 overo {
  18                         label = "overo:blue:COM";
  19                         pwms = <&twl_pwmled 1 7812500>;
  20                         max-brightness = <127>;
  21                         linux,default-trigger = "mmc0";
  22                 };
  23         };
  24
  25         sound {
  26                 compatible = "ti,omap-twl4030";
  27                 ti,model = "overo";
  28
  29                 ti,mcbsp = <&mcbsp2>;
  30         };
  31
  32         /* HS USB Port 2 Power */
  33         hsusb2_power: hsusb2_power_reg {
  34                 compatible = "regulator-fixed";
  35                 regulator-name = "hsusb2_vbus";
  36                 regulator-min-microvolt = <5000000>;
  37                 regulator-max-microvolt = <5000000>;
  38                 gpio = <&gpio6 8 GPIO_ACTIVE_HIGH>;             /* gpio_168: vbus enable */
  39                 startup-delay-us = <70000>;
  40                 enable-active-high;
  41         };
  42
  43         /* HS USB Host PHY on PORT 2 */
  44         hsusb2_phy: hsusb2_phy {
  45                 compatible = "usb-nop-xceiv";
  46                 reset-gpios = <&gpio6 23 GPIO_ACTIVE_LOW>;      /* gpio_183 */
  47                 vcc-supply = <&hsusb2_power>;
  48         };
  49
  50         /* Regulator to trigger the nPoweron signal of the Wifi module */
  51         w3cbw003c_npoweron: regulator-w3cbw003c-npoweron {
  52                 compatible = "regulator-fixed";
  53                 regulator-name = "regulator-w3cbw003c-npoweron";
  54                 regulator-min-microvolt = <3300000>;
  55                 regulator-max-microvolt = <3300000>;
  56                 gpio = <&gpio2 22 GPIO_ACTIVE_HIGH>;            /* gpio_54: nPoweron */
  57                 enable-active-high;
  58         };
  59
  60         /* Regulator to trigger the nReset signal of the Wifi module */
  61         w3cbw003c_wifi_nreset: regulator-w3cbw003c-wifi-nreset {
  62                 pinctrl-names = "default";
  63                 pinctrl-0 = <&w3cbw003c_pins &w3cbw003c_2_pins>;
  64                 compatible = "regulator-fixed";
  65                 regulator-name = "regulator-w3cbw003c-wifi-nreset";
  66                 regulator-min-microvolt = <3300000>;
  67                 regulator-max-microvolt = <3300000>;
  68                 gpio = <&gpio1 16 GPIO_ACTIVE_HIGH>;            /* gpio_16: WiFi nReset */
  69                 startup-delay-us = <10000>;
  70         };
  71
  72         /* Regulator to trigger the nReset signal of the Bluetooth module */
  73         w3cbw003c_bt_nreset: regulator-w3cbw003c-bt-nreset {
  74                 compatible = "regulator-fixed";
  75                 regulator-name = "regulator-w3cbw003c-bt-nreset";
  76                 regulator-min-microvolt = <3300000>;
  77                 regulator-max-microvolt = <3300000>;
  78                 gpio = <&gpio6 4 GPIO_ACTIVE_HIGH>;             /* gpio_164: BT nReset */
  79                 startup-delay-us = <10000>;
  80         };
  81 };
  82
  83 &omap3_pmx_core {
  84         pinctrl-names = "default";
  85         pinctrl-0 = <
  86                         &hsusb2_pins
  87         >;
  88
  89         uart2_pins: pinmux_uart2_pins {
  90                 pinctrl-single,pins = <
  91                         OMAP3_CORE1_IOPAD(0x216c, PIN_INPUT | MUX_MODE1)        /* mcbsp3_dx.uart2_cts */
  92                         OMAP3_CORE1_IOPAD(0x216e, PIN_OUTPUT | MUX_MODE1)       /* mcbsp3_dr.uart2_rts */
  93                         OMAP3_CORE1_IOPAD(0x2170, PIN_OUTPUT | MUX_MODE1)       /* mcbsp3_clk.uart2_tx */
  94                         OMAP3_CORE1_IOPAD(0x2172, PIN_INPUT | MUX_MODE1)        /* mcbsp3_fsx.uart2_rx */
  95                 >;
  96         };
  97
  98         i2c1_pins: pinmux_i2c1_pins {
  99                 pinctrl-single,pins = <
 100                         OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0)                /* i2c1_scl.i2c1_scl */
 101                         OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0)                /* i2c1_sda.i2c1_sda */
 102                 >;
 103         };
 104
 105         mmc1_pins: pinmux_mmc1_pins {
 106                 pinctrl-single,pins = <
 107                         OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0)         /* sdmmc1_clk.sdmmc1_clk */
 108                         OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0)         /* sdmmc1_cmd.sdmmc1_cmd */
 109                         OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0)         /* sdmmc1_dat0.sdmmc1_dat0 */
 110                         OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0)         /* sdmmc1_dat1.sdmmc1_dat1 */
 111                         OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0)         /* sdmmc1_dat2.sdmmc1_dat2 */
 112                         OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0)         /* sdmmc1_dat3.sdmmc1_dat3 */
 113                 >;
 114         };
 115
 116         mmc2_pins: pinmux_mmc2_pins {
 117                 pinctrl-single,pins = <
 118                         OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)         /* sdmmc2_clk.sdmmc2_clk */
 119                         OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0)         /* sdmmc2_cmd.sdmmc2_cmd */
 120                         OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0)         /* sdmmc2_dat0.sdmmc2_dat0 */
 121                         OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0)         /* sdmmc2_dat1.sdmmc2_dat1 */
 122                         OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0)         /* sdmmc2_dat2.sdmmc2_dat2 */
 123                         OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0)         /* sdmmc2_dat3.sdmmc2_dat3 */
 124                 >;
 125         };
 126
 127         /* WiFi/BT combo */
 128         w3cbw003c_pins: pinmux_w3cbw003c_pins {
 129                 pinctrl-single,pins = <
 130                         OMAP3_CORE1_IOPAD(0x20b4, PIN_OUTPUT | MUX_MODE4)               /* gpmc_ncs3.gpio_54 */
 131                         OMAP3_CORE1_IOPAD(0x219c, PIN_OUTPUT | MUX_MODE4)               /* uart3_rts_sd.gpio_164 */
 132                 >;
 133         };
 134
 135         hsusb2_pins: pinmux_hsusb2_pins {
 136                 pinctrl-single,pins = <
 137                         OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3)       /* mcspi1_cs3.hsusb2_data2 */
 138                         OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3)       /* mcspi2_clk.hsusb2_data7 */
 139                         OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3)       /* mcspi2_simo.hsusb2_data4 */
 140                         OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3)       /* mcspi2_somi.hsusb2_data5 */
 141                         OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3)       /* mcspi2_cs0.hsusb2_data6 */
 142                         OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3)       /* mcspi2_cs1.hsusb2_data3 */
 143                         OMAP3_CORE1_IOPAD(0x21be, PIN_OUTPUT | MUX_MODE4)               /* i2c2_scl.gpio_168 */
 144                         OMAP3_CORE1_IOPAD(0x21c0, PIN_OUTPUT | MUX_MODE4)               /* i2c2_sda.gpio_183 */
 145                 >;
 146         };
 147 };
 148
 149 &i2c1 {
 150         pinctrl-names = "default";
 151         pinctrl-0 = <&i2c1_pins>;
 152         clock-frequency = <2600000>;
 153
 154         twl: twl@48 {
 155                 reg = <0x48>;
 156                 interrupts = <7>; /* SYS_NIRQ cascaded to intc */
 157                 interrupt-parent = <&intc>;
 158
 159                 twl_audio: audio {
 160                         compatible = "ti,twl4030-audio";
 161                         codec {
 162                         };
 163                 };
 164         };
 165 };
 166
 167 #include "twl4030.dtsi"
 168 #include "twl4030_omap3.dtsi"
 169
 170 /* i2c2 pins are used for gpio */
 171 &i2c2 {
 172         status = "disabled";
 173 };
 174
 175 /* on board microSD slot */
 176 &mmc1 {
 177         pinctrl-names = "default";
 178         pinctrl-0 = <&mmc1_pins>;
 179         vmmc-supply = <&vmmc1>;
 180         bus-width = <4>;
 181 };
 182
 183 /* optional on board WiFi */
 184 &mmc2 {
 185         pinctrl-names = "default";
 186         pinctrl-0 = <&mmc2_pins>;
 187         vmmc-supply = <&w3cbw003c_npoweron>;
 188         vqmmc-supply = <&w3cbw003c_bt_nreset>;
 189         vmmc_aux-supply = <&w3cbw003c_wifi_nreset>;
 190         bus-width = <4>;
 191         cap-sdio-irq;
 192         non-removable;
 193 };
 194
 195 &twl_gpio {
 196         ti,use-leds;
 197 };
 198
 199 &usb_otg_hs {
 200         interface-type = <0>;
 201         usb-phy = <&usb2_phy>;
 202         phys = <&usb2_phy>;
 203         phy-names = "usb2-phy";
 204         mode = <3>;
 205         power = <50>;
 206 };
 207
 208 &usbhshost {
 209         port2-mode = "ehci-phy";
 210 };
 211
 212 &usbhsehci {
 213         phys = <0 &hsusb2_phy>;
 214 };
 215
 216 &uart2 {
 217         pinctrl-names = "default";
 218         pinctrl-0 = <&uart2_pins>;
 219 };
 220
 221 &mcbsp2 {
 222         status = "okay";
 223 };
 224
 225 &gpmc {
 226         ranges = <0 0 0x00000000 0x20000000>;
 227
 228         nand@0,0 {
 229                 compatible = "ti,omap2-nand";
 230                 linux,mtd-name= "micron,mt29c4g96maz";
 231                 reg = <0 0 4>;  /* CS0, offset 0, IO size 4 */
 232                 interrupt-parent = <&gpmc>;
 233                 interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
 234                              <1 IRQ_TYPE_NONE>; /* termcount */
 235                 nand-bus-width = <16>;
 236                 gpmc,device-width = <2>;
 237                 ti,nand-ecc-opt = "bch8";
 238
 239                 gpmc,sync-clk-ps = <0>;
 240                 gpmc,cs-on-ns = <0>;
 241                 gpmc,cs-rd-off-ns = <44>;
 242                 gpmc,cs-wr-off-ns = <44>;
 243                 gpmc,adv-on-ns = <6>;
 244                 gpmc,adv-rd-off-ns = <34>;
 245                 gpmc,adv-wr-off-ns = <44>;
 246                 gpmc,we-off-ns = <40>;
 247                 gpmc,oe-off-ns = <54>;
 248                 gpmc,access-ns = <64>;
 249                 gpmc,rd-cycle-ns = <82>;
 250                 gpmc,wr-cycle-ns = <82>;
 251                 gpmc,wr-access-ns = <40>;
 252                 gpmc,wr-data-mux-bus-ns = <0>;
 253
 254                 #address-cells = <1>;
 255                 #size-cells = <1>;
 256
 257                 partition@0 {
 258                         label = "SPL";
 259                         reg = <0 0x80000>; /* 512KiB */
 260                 };
 261                 partition@80000 {
 262                         label = "U-Boot";
 263                         reg = <0x80000 0x1C0000>; /* 1792KiB */
 264                 };
 265                 partition@1c0000 {
 266                         label = "Environment";
 267                         reg = <0x240000 0x40000>; /* 256KiB */
 268                 };
 269                 partition@280000 {
 270                         label = "Kernel";
 271                         reg = <0x280000 0x800000>; /* 8192KiB */
 272                 };
 273                 partition@780000 {
 274                         label = "Filesystem";
 275                         reg = <0xA80000 0>;
 276                         /* HACK: MTDPART_SIZ_FULL=0 so fill to end */
 277                 };
 278         };
 279 };