]> git.proxmox.com Git - mirror_ubuntu-hirsute-kernel.git/blob - arch/arm/boot/dts/r8a7790-lager.dts
Merge tag 'for-linus-5.9-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git...
[mirror_ubuntu-hirsute-kernel.git] / arch / arm / boot / dts / r8a7790-lager.dts
1 // SPDX-License-Identifier: GPL-2.0
2 /*
3 * Device Tree Source for the Lager board
4 *
5 * Copyright (C) 2013-2014 Renesas Solutions Corp.
6 * Copyright (C) 2014 Cogent Embedded, Inc.
7 * Copyright (C) 2015-2016 Renesas Electronics Corporation
8 */
9
10 /*
11 * SSI-AK4643
12 *
13 * SW1: 1: AK4643
14 * 2: CN22
15 * 3: ADV7511
16 *
17 * This command is required when Playback/Capture
18 *
19 * amixer set "LINEOUT Mixer DACL" on
20 * amixer set "DVC Out" 100%
21 * amixer set "DVC In" 100%
22 *
23 * You can use Mute
24 *
25 * amixer set "DVC Out Mute" on
26 * amixer set "DVC In Mute" on
27 *
28 * You can use Volume Ramp
29 *
30 * amixer set "DVC Out Ramp Up Rate" "0.125 dB/64 steps"
31 * amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
32 * amixer set "DVC Out Ramp" on
33 * aplay xxx.wav &
34 * amixer set "DVC Out" 80% // Volume Down
35 * amixer set "DVC Out" 100% // Volume Up
36 */
37
38 /dts-v1/;
39 #include "r8a7790.dtsi"
40 #include <dt-bindings/gpio/gpio.h>
41 #include <dt-bindings/input/input.h>
42
43 / {
44 model = "Lager";
45 compatible = "renesas,lager", "renesas,r8a7790";
46
47 aliases {
48 serial0 = &scif0;
49 serial1 = &scifa1;
50 i2c8 = &gpioi2c1;
51 i2c9 = &gpioi2c2;
52 i2c10 = &i2cexio0;
53 i2c11 = &i2cexio1;
54 i2c12 = &i2chdmi;
55 i2c13 = &i2cpwr;
56 };
57
58 chosen {
59 bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
60 stdout-path = "serial0:115200n8";
61 };
62
63 memory@40000000 {
64 device_type = "memory";
65 reg = <0 0x40000000 0 0x40000000>;
66 };
67
68 memory@140000000 {
69 device_type = "memory";
70 reg = <1 0x40000000 0 0xc0000000>;
71 };
72
73 lbsc {
74 #address-cells = <1>;
75 #size-cells = <1>;
76 };
77
78 keyboard {
79 compatible = "gpio-keys";
80
81 one {
82 linux,code = <KEY_1>;
83 label = "SW2-1";
84 wakeup-source;
85 debounce-interval = <20>;
86 gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
87 };
88 two {
89 linux,code = <KEY_2>;
90 label = "SW2-2";
91 wakeup-source;
92 debounce-interval = <20>;
93 gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
94 };
95 three {
96 linux,code = <KEY_3>;
97 label = "SW2-3";
98 wakeup-source;
99 debounce-interval = <20>;
100 gpios = <&gpio1 26 GPIO_ACTIVE_LOW>;
101 };
102 four {
103 linux,code = <KEY_4>;
104 label = "SW2-4";
105 wakeup-source;
106 debounce-interval = <20>;
107 gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
108 };
109 };
110
111 leds {
112 compatible = "gpio-leds";
113 led6 {
114 gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
115 };
116 led7 {
117 gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>;
118 };
119 led8 {
120 gpios = <&gpio5 17 GPIO_ACTIVE_HIGH>;
121 };
122 };
123
124 fixedregulator3v3: regulator-3v3 {
125 compatible = "regulator-fixed";
126 regulator-name = "fixed-3.3V";
127 regulator-min-microvolt = <3300000>;
128 regulator-max-microvolt = <3300000>;
129 regulator-boot-on;
130 regulator-always-on;
131 };
132
133 vcc_sdhi0: regulator-vcc-sdhi0 {
134 compatible = "regulator-fixed";
135
136 regulator-name = "SDHI0 Vcc";
137 regulator-min-microvolt = <3300000>;
138 regulator-max-microvolt = <3300000>;
139
140 gpio = <&gpio5 24 GPIO_ACTIVE_HIGH>;
141 enable-active-high;
142 };
143
144 vccq_sdhi0: regulator-vccq-sdhi0 {
145 compatible = "regulator-gpio";
146
147 regulator-name = "SDHI0 VccQ";
148 regulator-min-microvolt = <1800000>;
149 regulator-max-microvolt = <3300000>;
150
151 gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
152 gpios-states = <1>;
153 states = <3300000 1>, <1800000 0>;
154 };
155
156 vcc_sdhi2: regulator-vcc-sdhi2 {
157 compatible = "regulator-fixed";
158
159 regulator-name = "SDHI2 Vcc";
160 regulator-min-microvolt = <3300000>;
161 regulator-max-microvolt = <3300000>;
162
163 gpio = <&gpio5 25 GPIO_ACTIVE_HIGH>;
164 enable-active-high;
165 };
166
167 vccq_sdhi2: regulator-vccq-sdhi2 {
168 compatible = "regulator-gpio";
169
170 regulator-name = "SDHI2 VccQ";
171 regulator-min-microvolt = <1800000>;
172 regulator-max-microvolt = <3300000>;
173
174 gpios = <&gpio5 30 GPIO_ACTIVE_HIGH>;
175 gpios-states = <1>;
176 states = <3300000 1>, <1800000 0>;
177 };
178
179 audio_clock: audio_clock {
180 compatible = "fixed-clock";
181 #clock-cells = <0>;
182 clock-frequency = <11289600>;
183 };
184
185 rsnd_ak4643: sound {
186 compatible = "simple-audio-card";
187
188 simple-audio-card,format = "left_j";
189 simple-audio-card,bitclock-master = <&sndcodec>;
190 simple-audio-card,frame-master = <&sndcodec>;
191
192 sndcpu: simple-audio-card,cpu {
193 sound-dai = <&rcar_sound>;
194 };
195
196 sndcodec: simple-audio-card,codec {
197 sound-dai = <&ak4643>;
198 clocks = <&audio_clock>;
199 };
200 };
201
202 vga-encoder {
203 compatible = "adi,adv7123";
204
205 ports {
206 #address-cells = <1>;
207 #size-cells = <0>;
208
209 port@0 {
210 reg = <0>;
211 adv7123_in: endpoint {
212 remote-endpoint = <&du_out_rgb>;
213 };
214 };
215 port@1 {
216 reg = <1>;
217 adv7123_out: endpoint {
218 remote-endpoint = <&vga_in>;
219 };
220 };
221 };
222 };
223
224 vga {
225 compatible = "vga-connector";
226
227 port {
228 vga_in: endpoint {
229 remote-endpoint = <&adv7123_out>;
230 };
231 };
232 };
233
234 hdmi-in {
235 compatible = "hdmi-connector";
236 type = "a";
237
238 port {
239 hdmi_con_in: endpoint {
240 remote-endpoint = <&adv7612_in>;
241 };
242 };
243 };
244
245 cec_clock: cec-clock {
246 compatible = "fixed-clock";
247 #clock-cells = <0>;
248 clock-frequency = <12000000>;
249 };
250
251 hdmi-out {
252 compatible = "hdmi-connector";
253 type = "a";
254
255 port {
256 hdmi_con_out: endpoint {
257 remote-endpoint = <&adv7511_out>;
258 };
259 };
260 };
261
262 x2_clk: x2-clock {
263 compatible = "fixed-clock";
264 #clock-cells = <0>;
265 clock-frequency = <148500000>;
266 };
267
268 x13_clk: x13-clock {
269 compatible = "fixed-clock";
270 #clock-cells = <0>;
271 clock-frequency = <148500000>;
272 };
273
274 gpioi2c1: i2c-8 {
275 #address-cells = <1>;
276 #size-cells = <0>;
277 compatible = "i2c-gpio";
278 status = "disabled";
279 scl-gpios = <&gpio1 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
280 sda-gpios = <&gpio1 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
281 i2c-gpio,delay-us = <5>;
282 };
283
284 gpioi2c2: i2c-9 {
285 #address-cells = <1>;
286 #size-cells = <0>;
287 compatible = "i2c-gpio";
288 status = "disabled";
289 scl-gpios = <&gpio5 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
290 sda-gpios = <&gpio5 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
291 i2c-gpio,delay-us = <5>;
292 };
293
294 /*
295 * IIC0/I2C0 is routed to EXIO connector A, pins 114 (SCL) + 116 (SDA) only.
296 * We use the I2C demuxer, so the desired IP core can be selected at runtime
297 * depending on the use case (e.g. DMA with IIC0 or slave support with I2C0).
298 * Note: For testing the I2C slave feature, it is convenient to connect this
299 * bus with IIC3 on pins 110 (SCL) + 112 (SDA), select I2C0 at runtime, and
300 * instantiate the slave device at runtime according to the documentation.
301 * You can then communicate with the slave via IIC3.
302 *
303 * IIC0/I2C0 does not appear to support fallback to GPIO.
304 */
305 i2cexio0: i2c-10 {
306 compatible = "i2c-demux-pinctrl";
307 i2c-parent = <&iic0>, <&i2c0>;
308 i2c-bus-name = "i2c-exio0";
309 #address-cells = <1>;
310 #size-cells = <0>;
311 };
312
313 /*
314 * IIC1/I2C1 is routed to EXIO connector A, pins 78 (SCL) + 80 (SDA).
315 * This is similar to the arangement described for i2cexio0 (above)
316 * with a fallback to GPIO also provided.
317 */
318 i2cexio1: i2c-11 {
319 compatible = "i2c-demux-pinctrl";
320 i2c-parent = <&iic1>, <&i2c1>, <&gpioi2c1>;
321 i2c-bus-name = "i2c-exio1";
322 #address-cells = <1>;
323 #size-cells = <0>;
324 };
325
326 /*
327 * IIC2 and I2C2 may be switched using pinmux.
328 * A fallback to GPIO is also provided.
329 */
330 i2chdmi: i2c-12 {
331 compatible = "i2c-demux-pinctrl";
332 i2c-parent = <&iic2>, <&i2c2>, <&gpioi2c2>;
333 i2c-bus-name = "i2c-hdmi";
334 #address-cells = <1>;
335 #size-cells = <0>;
336
337 ak4643: codec@12 {
338 compatible = "asahi-kasei,ak4643";
339 #sound-dai-cells = <0>;
340 reg = <0x12>;
341 };
342
343 composite-in@20 {
344 compatible = "adi,adv7180";
345 reg = <0x20>;
346
347 port {
348 adv7180: endpoint {
349 bus-width = <8>;
350 remote-endpoint = <&vin1ep0>;
351 };
352 };
353 };
354
355 hdmi@39 {
356 compatible = "adi,adv7511w";
357 reg = <0x39>;
358 interrupt-parent = <&gpio1>;
359 interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
360 clocks = <&cec_clock>;
361 clock-names = "cec";
362
363 adi,input-depth = <8>;
364 adi,input-colorspace = "rgb";
365 adi,input-clock = "1x";
366
367 ports {
368 #address-cells = <1>;
369 #size-cells = <0>;
370
371 port@0 {
372 reg = <0>;
373 adv7511_in: endpoint {
374 remote-endpoint = <&lvds0_out>;
375 };
376 };
377
378 port@1 {
379 reg = <1>;
380 adv7511_out: endpoint {
381 remote-endpoint = <&hdmi_con_out>;
382 };
383 };
384 };
385 };
386
387 hdmi-in@4c {
388 compatible = "adi,adv7612";
389 reg = <0x4c>;
390 interrupt-parent = <&gpio1>;
391 interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
392 default-input = <0>;
393
394 ports {
395 #address-cells = <1>;
396 #size-cells = <0>;
397
398 port@0 {
399 reg = <0>;
400 adv7612_in: endpoint {
401 remote-endpoint = <&hdmi_con_in>;
402 };
403 };
404
405 port@2 {
406 reg = <2>;
407 adv7612_out: endpoint {
408 remote-endpoint = <&vin0ep2>;
409 };
410 };
411 };
412 };
413 };
414
415 /*
416 * IIC3 and I2C3 may be switched using pinmux.
417 * IIC3/I2C3 does not appear to support fallback to GPIO.
418 */
419 i2cpwr: i2c-13 {
420 compatible = "i2c-demux-pinctrl";
421 pinctrl-names = "default";
422 pinctrl-0 = <&pmic_irq_pins>;
423 i2c-parent = <&iic3>, <&i2c3>;
424 i2c-bus-name = "i2c-pwr";
425 #address-cells = <1>;
426 #size-cells = <0>;
427
428 pmic@58 {
429 compatible = "dlg,da9063";
430 reg = <0x58>;
431 interrupt-parent = <&irqc0>;
432 interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
433 interrupt-controller;
434
435 rtc {
436 compatible = "dlg,da9063-rtc";
437 };
438
439 wdt {
440 compatible = "dlg,da9063-watchdog";
441 };
442 };
443
444 vdd_dvfs: regulator@68 {
445 compatible = "dlg,da9210";
446 reg = <0x68>;
447 interrupt-parent = <&irqc0>;
448 interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
449
450 regulator-min-microvolt = <1000000>;
451 regulator-max-microvolt = <1000000>;
452 regulator-boot-on;
453 regulator-always-on;
454 };
455 };
456 };
457
458 &du {
459 pinctrl-0 = <&du_pins>;
460 pinctrl-names = "default";
461 status = "okay";
462
463 clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 722>,
464 <&x13_clk>, <&x2_clk>;
465 clock-names = "du.0", "du.1", "du.2", "dclkin.0", "dclkin.1";
466
467 ports {
468 port@0 {
469 endpoint {
470 remote-endpoint = <&adv7123_in>;
471 };
472 };
473 };
474 };
475
476 &lvds0 {
477 status = "okay";
478
479 ports {
480 port@1 {
481 endpoint {
482 remote-endpoint = <&adv7511_in>;
483 };
484 };
485 };
486 };
487
488 &lvds1 {
489 ports {
490 port@1 {
491 lvds_connector: endpoint {
492 };
493 };
494 };
495 };
496
497 &extal_clk {
498 clock-frequency = <20000000>;
499 };
500
501 &pfc {
502 pinctrl-0 = <&scif_clk_pins>;
503 pinctrl-names = "default";
504
505 du_pins: du {
506 groups = "du_rgb666", "du_sync_1", "du_clk_out_0";
507 function = "du";
508 };
509
510 scif0_pins: scif0 {
511 groups = "scif0_data";
512 function = "scif0";
513 };
514
515 scif_clk_pins: scif_clk {
516 groups = "scif_clk";
517 function = "scif_clk";
518 };
519
520 ether_pins: ether {
521 groups = "eth_link", "eth_mdio", "eth_rmii";
522 function = "eth";
523 };
524
525 phy1_pins: phy1 {
526 groups = "intc_irq0";
527 function = "intc";
528 };
529
530 scifa1_pins: scifa1 {
531 groups = "scifa1_data";
532 function = "scifa1";
533 };
534
535 sdhi0_pins: sd0 {
536 groups = "sdhi0_data4", "sdhi0_ctrl";
537 function = "sdhi0";
538 power-source = <3300>;
539 };
540
541 sdhi0_pins_uhs: sd0_uhs {
542 groups = "sdhi0_data4", "sdhi0_ctrl";
543 function = "sdhi0";
544 power-source = <1800>;
545 };
546
547 sdhi2_pins: sd2 {
548 groups = "sdhi2_data4", "sdhi2_ctrl";
549 function = "sdhi2";
550 power-source = <3300>;
551 };
552
553 sdhi2_pins_uhs: sd2_uhs {
554 groups = "sdhi2_data4", "sdhi2_ctrl";
555 function = "sdhi2";
556 power-source = <1800>;
557 };
558
559 mmc1_pins: mmc1 {
560 groups = "mmc1_data8", "mmc1_ctrl";
561 function = "mmc1";
562 };
563
564 qspi_pins: qspi {
565 groups = "qspi_ctrl", "qspi_data4";
566 function = "qspi";
567 };
568
569 msiof1_pins: msiof1 {
570 groups = "msiof1_clk", "msiof1_sync", "msiof1_rx",
571 "msiof1_tx";
572 function = "msiof1";
573 };
574
575 i2c0_pins: i2c0 {
576 groups = "i2c0";
577 function = "i2c0";
578 };
579
580 iic0_pins: iic0 {
581 groups = "iic0";
582 function = "iic0";
583 };
584
585 i2c1_pins: i2c1 {
586 groups = "i2c1";
587 function = "i2c1";
588 };
589
590 iic1_pins: iic1 {
591 groups = "iic1";
592 function = "iic1";
593 };
594
595 i2c2_pins: i2c2 {
596 groups = "i2c2";
597 function = "i2c2";
598 };
599
600 iic2_pins: iic2 {
601 groups = "iic2";
602 function = "iic2";
603 };
604
605 i2c3_pins: i2c3 {
606 groups = "i2c3";
607 function = "i2c3";
608 };
609
610 iic3_pins: iic3 {
611 groups = "iic3";
612 function = "iic3";
613 };
614
615 pmic_irq_pins: pmicirq {
616 groups = "intc_irq2";
617 function = "intc";
618 };
619
620 hsusb_pins: hsusb {
621 groups = "usb0_ovc_vbus";
622 function = "usb0";
623 };
624
625 usb0_pins: usb0 {
626 groups = "usb0";
627 function = "usb0";
628 };
629
630 usb1_pins: usb1 {
631 groups = "usb1";
632 function = "usb1";
633 };
634
635 usb2_pins: usb2 {
636 groups = "usb2";
637 function = "usb2";
638 };
639
640 vin0_pins: vin0 {
641 groups = "vin0_data24", "vin0_sync", "vin0_clkenb", "vin0_clk";
642 function = "vin0";
643 };
644
645 vin1_pins: vin1 {
646 groups = "vin1_data8", "vin1_clk";
647 function = "vin1";
648 };
649
650 sound_pins: sound {
651 groups = "ssi0129_ctrl", "ssi0_data", "ssi1_data";
652 function = "ssi";
653 };
654
655 sound_clk_pins: sound_clk {
656 groups = "audio_clk_a";
657 function = "audio_clk";
658 };
659 };
660
661 &ether {
662 pinctrl-0 = <&ether_pins &phy1_pins>;
663 pinctrl-names = "default";
664
665 phy-handle = <&phy1>;
666 renesas,ether-link-active-low;
667 status = "okay";
668
669 phy1: ethernet-phy@1 {
670 reg = <1>;
671 interrupt-parent = <&irqc0>;
672 interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
673 micrel,led-mode = <1>;
674 reset-gpios = <&gpio5 31 GPIO_ACTIVE_LOW>;
675 };
676 };
677
678 &cmt0 {
679 status = "okay";
680 };
681
682 &mmcif1 {
683 pinctrl-0 = <&mmc1_pins>;
684 pinctrl-names = "default";
685
686 vmmc-supply = <&fixedregulator3v3>;
687 bus-width = <8>;
688 non-removable;
689 status = "okay";
690 };
691
692 &sata1 {
693 status = "okay";
694 };
695
696 &qspi {
697 pinctrl-0 = <&qspi_pins>;
698 pinctrl-names = "default";
699
700 status = "okay";
701
702 flash: flash@0 {
703 compatible = "spansion,s25fl512s", "jedec,spi-nor";
704 reg = <0>;
705 spi-max-frequency = <30000000>;
706 spi-tx-bus-width = <4>;
707 spi-rx-bus-width = <4>;
708 spi-cpha;
709 spi-cpol;
710 m25p,fast-read;
711
712 partitions {
713 compatible = "fixed-partitions";
714 #address-cells = <1>;
715 #size-cells = <1>;
716
717 partition@0 {
718 label = "loader";
719 reg = <0x00000000 0x00040000>;
720 read-only;
721 };
722 partition@40000 {
723 label = "user";
724 reg = <0x00040000 0x00400000>;
725 read-only;
726 };
727 partition@440000 {
728 label = "flash";
729 reg = <0x00440000 0x03bc0000>;
730 };
731 };
732 };
733 };
734
735 &scif0 {
736 pinctrl-0 = <&scif0_pins>;
737 pinctrl-names = "default";
738
739 status = "okay";
740 };
741
742 &scifa1 {
743 pinctrl-0 = <&scifa1_pins>;
744 pinctrl-names = "default";
745
746 status = "okay";
747 };
748
749 &scif_clk {
750 clock-frequency = <14745600>;
751 };
752
753 &msiof1 {
754 pinctrl-0 = <&msiof1_pins>;
755 pinctrl-names = "default";
756
757 status = "okay";
758
759 pmic: pmic@0 {
760 compatible = "renesas,r2a11302ft";
761 reg = <0>;
762 spi-max-frequency = <6000000>;
763 spi-cpol;
764 spi-cpha;
765 };
766 };
767
768 &sdhi0 {
769 pinctrl-0 = <&sdhi0_pins>;
770 pinctrl-1 = <&sdhi0_pins_uhs>;
771 pinctrl-names = "default", "state_uhs";
772
773 vmmc-supply = <&vcc_sdhi0>;
774 vqmmc-supply = <&vccq_sdhi0>;
775 cd-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>;
776 sd-uhs-sdr50;
777 sd-uhs-sdr104;
778 status = "okay";
779 };
780
781 &sdhi2 {
782 pinctrl-0 = <&sdhi2_pins>;
783 pinctrl-1 = <&sdhi2_pins_uhs>;
784 pinctrl-names = "default", "state_uhs";
785
786 vmmc-supply = <&vcc_sdhi2>;
787 vqmmc-supply = <&vccq_sdhi2>;
788 cd-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>;
789 sd-uhs-sdr50;
790 status = "okay";
791 };
792
793 &cpu0 {
794 cpu0-supply = <&vdd_dvfs>;
795 };
796
797 &i2c0 {
798 pinctrl-0 = <&i2c0_pins>;
799 pinctrl-names = "i2c-exio0";
800 };
801
802 &iic0 {
803 pinctrl-0 = <&iic0_pins>;
804 pinctrl-names = "i2c-exio0";
805 };
806
807 &i2c1 {
808 pinctrl-0 = <&i2c1_pins>;
809 pinctrl-names = "i2c-exio1";
810 };
811
812 &iic1 {
813 pinctrl-0 = <&iic1_pins>;
814 pinctrl-names = "i2c-exio1";
815 };
816
817 &i2c2 {
818 pinctrl-0 = <&i2c2_pins>;
819 pinctrl-names = "i2c-hdmi";
820
821 clock-frequency = <100000>;
822 };
823
824 &iic2 {
825 pinctrl-0 = <&iic2_pins>;
826 pinctrl-names = "i2c-hdmi";
827
828 clock-frequency = <100000>;
829 };
830
831 &i2c3 {
832 pinctrl-0 = <&i2c3_pins>;
833 pinctrl-names = "i2c-pwr";
834 };
835
836 &iic3 {
837 pinctrl-0 = <&iic3_pins>;
838 pinctrl-names = "i2c-pwr";
839 };
840
841 &pci0 {
842 status = "okay";
843 pinctrl-0 = <&usb0_pins>;
844 pinctrl-names = "default";
845 };
846
847 &pci1 {
848 status = "okay";
849 pinctrl-0 = <&usb1_pins>;
850 pinctrl-names = "default";
851 };
852
853 &xhci {
854 status = "okay";
855 pinctrl-0 = <&usb2_pins>;
856 pinctrl-names = "default";
857 };
858
859 &pci2 {
860 status = "okay";
861 pinctrl-0 = <&usb2_pins>;
862 pinctrl-names = "default";
863 };
864
865 &hsusb {
866 status = "okay";
867 pinctrl-0 = <&hsusb_pins>;
868 pinctrl-names = "default";
869 renesas,enable-gpio = <&gpio5 18 GPIO_ACTIVE_HIGH>;
870 };
871
872 &usbphy {
873 status = "okay";
874 };
875
876 /* HDMI video input */
877 &vin0 {
878 pinctrl-0 = <&vin0_pins>;
879 pinctrl-names = "default";
880
881 status = "okay";
882
883 port {
884 vin0ep2: endpoint {
885 remote-endpoint = <&adv7612_out>;
886 bus-width = <24>;
887 hsync-active = <0>;
888 vsync-active = <0>;
889 pclk-sample = <1>;
890 data-active = <1>;
891 };
892 };
893 };
894
895 /* composite video input */
896 &vin1 {
897 pinctrl-0 = <&vin1_pins>;
898 pinctrl-names = "default";
899
900 status = "okay";
901
902 port {
903 vin1ep0: endpoint {
904 remote-endpoint = <&adv7180>;
905 bus-width = <8>;
906 };
907 };
908 };
909
910 &rcar_sound {
911 pinctrl-0 = <&sound_pins &sound_clk_pins>;
912 pinctrl-names = "default";
913
914 /* Single DAI */
915 #sound-dai-cells = <0>;
916
917 status = "okay";
918
919 rcar_sound,dai {
920 dai0 {
921 playback = <&ssi0 &src2 &dvc0>;
922 capture = <&ssi1 &src3 &dvc1>;
923 };
924 };
925 };
926
927 &rwdt {
928 timeout-sec = <60>;
929 status = "okay";
930 };
931
932 &ssi1 {
933 shared-pin;
934 };