arch/arm/mach-imx/Kconfig

   1 menuconfig ARCH_MXC
   2         bool "Freescale i.MX family"
   3         depends on ARCH_MULTI_V4_V5 || ARCH_MULTI_V6_V7 || ARM_SINGLE_ARMV7M
   4         select ARCH_SUPPORTS_BIG_ENDIAN
   5         select CLKSRC_IMX_GPT
   6         select GENERIC_IRQ_CHIP
   7         select GPIOLIB
   8         select PINCTRL
   9         select PM_OPP if PM
  10         select SOC_BUS
  11         select SRAM
  12         help
  13           Support for Freescale MXC/iMX-based family of processors
  14
  15 if ARCH_MXC
  16
  17 config MXC_TZIC
  18         bool
  19
  20 config MXC_AVIC
  21         bool
  22
  23 config MXC_DEBUG_BOARD
  24         bool "Enable MXC debug board(for 3-stack)"
  25         depends on MACH_MX27_3DS || MACH_MX31_3DS || MACH_MX35_3DS
  26         help
  27           The debug board is an integral part of the MXC 3-stack(PDK)
  28           platforms, it can be attached or removed from the peripheral
  29           board. On debug board, several debug devices(ethernet, UART,
  30           buttons, LEDs and JTAG) are implemented. Between the MCU and
  31           these devices, a CPLD is added as a bridge which performs
  32           data/address de-multiplexing and decode, signal level shift,
  33           interrupt control and various board functions.
  34
  35 config HAVE_IMX_ANATOP
  36         bool
  37
  38 config HAVE_IMX_GPC
  39         bool
  40         select PM_GENERIC_DOMAINS if PM
  41
  42 config HAVE_IMX_MMDC
  43         bool
  44
  45 config HAVE_IMX_SRC
  46         def_bool y if SMP
  47         select ARCH_HAS_RESET_CONTROLLER
  48
  49 config IMX_HAVE_IOMUX_V1
  50         bool
  51
  52 config ARCH_MXC_IOMUX_V3
  53         bool
  54
  55 config SOC_IMX21
  56         bool
  57         select CPU_ARM926T
  58         select IMX_HAVE_IOMUX_V1
  59         select MXC_AVIC
  60
  61 config SOC_IMX27
  62         bool
  63         select CPU_ARM926T
  64         select IMX_HAVE_IOMUX_V1
  65         select MXC_AVIC
  66         select PINCTRL_IMX27
  67
  68 config SOC_IMX31
  69         bool
  70         select CPU_V6
  71         select MXC_AVIC
  72
  73 config SOC_IMX35
  74         bool
  75         select ARCH_MXC_IOMUX_V3
  76         select MXC_AVIC
  77         select PINCTRL_IMX35
  78
  79 if ARCH_MULTI_V5
  80
  81 comment "MX21 platforms:"
  82
  83 config MACH_MX21ADS
  84         bool "MX21ADS platform"
  85         select IMX_HAVE_PLATFORM_IMX_FB
  86         select IMX_HAVE_PLATFORM_IMX_UART
  87         select IMX_HAVE_PLATFORM_MXC_MMC
  88         select IMX_HAVE_PLATFORM_MXC_NAND
  89         select SOC_IMX21
  90         help
  91           Include support for MX21ADS platform. This includes specific
  92           configurations for the board and its peripherals.
  93
  94 comment "MX27 platforms:"
  95
  96 config MACH_MX27ADS
  97         bool "MX27ADS platform"
  98         select IMX_HAVE_PLATFORM_IMX_FB
  99         select IMX_HAVE_PLATFORM_IMX_I2C
 100         select IMX_HAVE_PLATFORM_IMX_UART
 101         select IMX_HAVE_PLATFORM_MXC_MMC
 102         select IMX_HAVE_PLATFORM_MXC_NAND
 103         select IMX_HAVE_PLATFORM_MXC_W1
 104         select SOC_IMX27
 105         help
 106           Include support for MX27ADS platform. This includes specific
 107           configurations for the board and its peripherals.
 108
 109 config MACH_MX27_3DS
 110         bool "MX27PDK platform"
 111         select IMX_HAVE_PLATFORM_FSL_USB2_UDC
 112         select IMX_HAVE_PLATFORM_IMX2_WDT
 113         select IMX_HAVE_PLATFORM_IMX_FB
 114         select IMX_HAVE_PLATFORM_IMX_I2C
 115         select IMX_HAVE_PLATFORM_IMX_KEYPAD
 116         select IMX_HAVE_PLATFORM_IMX_SSI
 117         select IMX_HAVE_PLATFORM_IMX_UART
 118         select IMX_HAVE_PLATFORM_MX2_CAMERA
 119         select IMX_HAVE_PLATFORM_MXC_EHCI
 120         select IMX_HAVE_PLATFORM_MXC_MMC
 121         select IMX_HAVE_PLATFORM_SPI_IMX
 122         select MXC_DEBUG_BOARD
 123         select USB_ULPI_VIEWPORT if USB_ULPI
 124         select SOC_IMX27
 125         help
 126           Include support for MX27PDK platform. This includes specific
 127           configurations for the board and its peripherals.
 128
 129 config MACH_IMX27_VISSTRIM_M10
 130         bool "Vista Silicon i.MX27 Visstrim_m10"
 131         select IMX_HAVE_PLATFORM_GPIO_KEYS
 132         select IMX_HAVE_PLATFORM_IMX_I2C
 133         select IMX_HAVE_PLATFORM_IMX_SSI
 134         select IMX_HAVE_PLATFORM_IMX_UART
 135         select IMX_HAVE_PLATFORM_MX2_CAMERA
 136         select IMX_HAVE_PLATFORM_MX2_EMMA
 137         select IMX_HAVE_PLATFORM_MXC_EHCI
 138         select IMX_HAVE_PLATFORM_MXC_MMC
 139         select LEDS_GPIO_REGISTER
 140         select SOC_IMX27
 141         help
 142           Include support for Visstrim_m10 platform and its different variants.
 143           This includes specific configurations for the board and its
 144           peripherals.
 145
 146 config MACH_PCA100
 147         bool "Phytec phyCARD-s (pca100)"
 148         select IMX_HAVE_PLATFORM_FSL_USB2_UDC
 149         select IMX_HAVE_PLATFORM_IMX2_WDT
 150         select IMX_HAVE_PLATFORM_IMX_FB
 151         select IMX_HAVE_PLATFORM_IMX_I2C
 152         select IMX_HAVE_PLATFORM_IMX_SSI
 153         select IMX_HAVE_PLATFORM_IMX_UART
 154         select IMX_HAVE_PLATFORM_MXC_EHCI
 155         select IMX_HAVE_PLATFORM_MXC_MMC
 156         select IMX_HAVE_PLATFORM_MXC_NAND
 157         select IMX_HAVE_PLATFORM_MXC_W1
 158         select IMX_HAVE_PLATFORM_SPI_IMX
 159         select USB_ULPI_VIEWPORT if USB_ULPI
 160         select SOC_IMX27
 161         help
 162           Include support for phyCARD-s (aka pca100) platform. This
 163           includes specific configurations for the module and its peripherals.
 164
 165 config MACH_IMX27_DT
 166         bool "Support i.MX27 platforms from device tree"
 167         select SOC_IMX27
 168         help
 169           Include support for Freescale i.MX27 based platforms
 170           using the device tree for discovery
 171
 172 endif
 173
 174 if ARCH_MULTI_V6
 175
 176 comment "MX31 platforms:"
 177
 178 config MACH_MX31ADS
 179         bool "Support MX31ADS platforms"
 180         default y
 181         select IMX_HAVE_PLATFORM_IMX_I2C
 182         select IMX_HAVE_PLATFORM_IMX_SSI
 183         select IMX_HAVE_PLATFORM_IMX_UART
 184         select SOC_IMX31
 185         help
 186           Include support for MX31ADS platform. This includes specific
 187           configurations for the board and its peripherals.
 188
 189 config MACH_MX31ADS_WM1133_EV1
 190         bool "Support Wolfson Microelectronics 1133-EV1 module"
 191         depends on MACH_MX31ADS
 192         depends on MFD_WM8350_I2C
 193         depends on REGULATOR_WM8350 = y
 194         help
 195           Include support for the Wolfson Microelectronics 1133-EV1 PMU
 196           and audio module for the MX31ADS platform.
 197
 198 config MACH_MX31LILLY
 199         bool "Support MX31 LILLY-1131 platforms (INCO startec)"
 200         select IMX_HAVE_PLATFORM_IMX_UART
 201         select IMX_HAVE_PLATFORM_IPU_CORE
 202         select IMX_HAVE_PLATFORM_MXC_EHCI
 203         select IMX_HAVE_PLATFORM_MXC_MMC
 204         select IMX_HAVE_PLATFORM_SPI_IMX
 205         select USB_ULPI_VIEWPORT if USB_ULPI
 206         select SOC_IMX31
 207         help
 208           Include support for mx31 based LILLY1131 modules. This includes
 209           specific configurations for the board and its peripherals.
 210
 211 config MACH_MX31LITE
 212         bool "Support MX31 LITEKIT (LogicPD)"
 213         select IMX_HAVE_PLATFORM_IMX2_WDT
 214         select IMX_HAVE_PLATFORM_IMX_UART
 215         select IMX_HAVE_PLATFORM_MXC_EHCI
 216         select IMX_HAVE_PLATFORM_MXC_MMC
 217         select IMX_HAVE_PLATFORM_MXC_NAND
 218         select IMX_HAVE_PLATFORM_MXC_RTC
 219         select IMX_HAVE_PLATFORM_SPI_IMX
 220         select LEDS_GPIO_REGISTER
 221         select USB_ULPI_VIEWPORT if USB_ULPI
 222         select SOC_IMX31
 223         help
 224           Include support for MX31 LITEKIT platform. This includes specific
 225           configurations for the board and its peripherals.
 226
 227 config MACH_PCM037
 228         bool "Support Phytec pcm037 (i.MX31) platforms"
 229         select IMX_HAVE_PLATFORM_FSL_USB2_UDC
 230         select IMX_HAVE_PLATFORM_IMX2_WDT
 231         select IMX_HAVE_PLATFORM_IMX_I2C
 232         select IMX_HAVE_PLATFORM_IMX_UART
 233         select IMX_HAVE_PLATFORM_IPU_CORE
 234         select IMX_HAVE_PLATFORM_MXC_EHCI
 235         select IMX_HAVE_PLATFORM_MXC_MMC
 236         select IMX_HAVE_PLATFORM_MXC_NAND
 237         select IMX_HAVE_PLATFORM_MXC_W1
 238         select USB_ULPI_VIEWPORT if USB_ULPI
 239         select SOC_IMX31
 240         help
 241           Include support for Phytec pcm037 platform. This includes
 242           specific configurations for the board and its peripherals.
 243
 244 config MACH_PCM037_EET
 245         bool "Support pcm037 EET board extensions"
 246         depends on MACH_PCM037
 247         select IMX_HAVE_PLATFORM_GPIO_KEYS
 248         select IMX_HAVE_PLATFORM_SPI_IMX
 249         help
 250           Add support for PCM037 EET baseboard extensions. If you are using the
 251           OLED display with EET, use "video=mx3fb:CMEL-OLED" kernel
 252           command-line parameter.
 253
 254 config MACH_MX31_3DS
 255         bool "Support MX31PDK (3DS)"
 256         select IMX_HAVE_PLATFORM_FSL_USB2_UDC
 257         select IMX_HAVE_PLATFORM_IMX2_WDT
 258         select IMX_HAVE_PLATFORM_IMX_I2C
 259         select IMX_HAVE_PLATFORM_IMX_KEYPAD
 260         select IMX_HAVE_PLATFORM_IMX_SSI
 261         select IMX_HAVE_PLATFORM_IMX_UART
 262         select IMX_HAVE_PLATFORM_IPU_CORE
 263         select IMX_HAVE_PLATFORM_MXC_EHCI
 264         select IMX_HAVE_PLATFORM_MXC_MMC
 265         select IMX_HAVE_PLATFORM_MXC_NAND
 266         select IMX_HAVE_PLATFORM_SPI_IMX
 267         select MXC_DEBUG_BOARD
 268         select USB_ULPI_VIEWPORT if USB_ULPI
 269         select SOC_IMX31
 270         help
 271           Include support for MX31PDK (3DS) platform. This includes specific
 272           configurations for the board and its peripherals.
 273
 274 config MACH_MX31_3DS_MXC_NAND_USE_BBT
 275         bool "Make the MXC NAND driver use the in flash Bad Block Table"
 276         depends on MACH_MX31_3DS
 277         depends on MTD_NAND_MXC
 278         help
 279           Enable this if you want that the MXC NAND driver uses the in flash
 280           Bad Block Table to know what blocks are bad instead of scanning the
 281           entire flash looking for bad block markers.
 282
 283 config MACH_MX31MOBOARD
 284         bool "Support mx31moboard platforms (EPFL Mobots group)"
 285         select IMX_HAVE_PLATFORM_FSL_USB2_UDC
 286         select IMX_HAVE_PLATFORM_IMX2_WDT
 287         select IMX_HAVE_PLATFORM_IMX_I2C
 288         select IMX_HAVE_PLATFORM_IMX_SSI
 289         select IMX_HAVE_PLATFORM_IMX_UART
 290         select IMX_HAVE_PLATFORM_IPU_CORE
 291         select IMX_HAVE_PLATFORM_MXC_EHCI
 292         select IMX_HAVE_PLATFORM_MXC_MMC
 293         select IMX_HAVE_PLATFORM_SPI_IMX
 294         select LEDS_GPIO_REGISTER
 295         select USB_ULPI_VIEWPORT if USB_ULPI
 296         select SOC_IMX31
 297         help
 298           Include support for mx31moboard platform. This includes specific
 299           configurations for the board and its peripherals.
 300
 301 config MACH_QONG
 302         bool "Support Dave/DENX QongEVB-LITE platform"
 303         select IMX_HAVE_PLATFORM_IMX2_WDT
 304         select IMX_HAVE_PLATFORM_IMX_UART
 305         select SOC_IMX31
 306         help
 307           Include support for Dave/DENX QongEVB-LITE platform. This includes
 308           specific configurations for the board and its peripherals.
 309
 310 config MACH_ARMADILLO5X0
 311         bool "Support Atmark Armadillo-500 Development Base Board"
 312         select IMX_HAVE_PLATFORM_GPIO_KEYS
 313         select IMX_HAVE_PLATFORM_IMX_I2C
 314         select IMX_HAVE_PLATFORM_IMX_UART
 315         select IMX_HAVE_PLATFORM_IPU_CORE
 316         select IMX_HAVE_PLATFORM_MXC_EHCI
 317         select IMX_HAVE_PLATFORM_MXC_MMC
 318         select IMX_HAVE_PLATFORM_MXC_NAND
 319         select USB_ULPI_VIEWPORT if USB_ULPI
 320         select SOC_IMX31
 321         help
 322           Include support for Atmark Armadillo-500 platform. This includes
 323           specific configurations for the board and its peripherals.
 324
 325 config MACH_KZM_ARM11_01
 326         bool "Support KZM-ARM11-01(Kyoto Microcomputer)"
 327         select IMX_HAVE_PLATFORM_IMX_UART
 328         select SOC_IMX31
 329         help
 330           Include support for KZM-ARM11-01. This includes specific
 331           configurations for the board and its peripherals.
 332
 333 config MACH_BUG
 334         bool "Support Buglabs BUGBase platform"
 335         default y
 336         select IMX_HAVE_PLATFORM_IMX_UART
 337         select SOC_IMX31
 338         help
 339           Include support for BUGBase 1.3 platform. This includes specific
 340           configurations for the board and its peripherals.
 341
 342 config MACH_IMX31_DT
 343         bool "Support i.MX31 platforms from device tree"
 344         select SOC_IMX31
 345         help
 346           Include support for Freescale i.MX31 based platforms
 347           using the device tree for discovery.
 348
 349 comment "MX35 platforms:"
 350
 351 config MACH_IMX35_DT
 352         bool "Support i.MX35 platforms from device tree"
 353         select SOC_IMX35
 354         help
 355           Include support for Freescale i.MX35 based platforms
 356           using the device tree for discovery.
 357
 358 config MACH_PCM043
 359         bool "Support Phytec pcm043 (i.MX35) platforms"
 360         select IMX_HAVE_PLATFORM_FLEXCAN
 361         select IMX_HAVE_PLATFORM_FSL_USB2_UDC
 362         select IMX_HAVE_PLATFORM_IMX2_WDT
 363         select IMX_HAVE_PLATFORM_IMX_I2C
 364         select IMX_HAVE_PLATFORM_IMX_SSI
 365         select IMX_HAVE_PLATFORM_IMX_UART
 366         select IMX_HAVE_PLATFORM_IPU_CORE
 367         select IMX_HAVE_PLATFORM_MXC_EHCI
 368         select IMX_HAVE_PLATFORM_MXC_NAND
 369         select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX
 370         select USB_ULPI_VIEWPORT if USB_ULPI
 371         select SOC_IMX35
 372         help
 373           Include support for Phytec pcm043 platform. This includes
 374           specific configurations for the board and its peripherals.
 375
 376 config MACH_MX35_3DS
 377         bool "Support MX35PDK platform"
 378         select IMX_HAVE_PLATFORM_FSL_USB2_UDC
 379         select IMX_HAVE_PLATFORM_IMX2_WDT
 380         select IMX_HAVE_PLATFORM_IMX_FB
 381         select IMX_HAVE_PLATFORM_IMX_I2C
 382         select IMX_HAVE_PLATFORM_IMX_UART
 383         select IMX_HAVE_PLATFORM_IPU_CORE
 384         select IMX_HAVE_PLATFORM_MXC_EHCI
 385         select IMX_HAVE_PLATFORM_MXC_NAND
 386         select IMX_HAVE_PLATFORM_MXC_RTC
 387         select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX
 388         select MXC_DEBUG_BOARD
 389         select SOC_IMX35
 390         help
 391           Include support for MX35PDK platform. This includes specific
 392           configurations for the board and its peripherals.
 393
 394 config MACH_VPR200
 395         bool "Support VPR200 platform"
 396         select IMX_HAVE_PLATFORM_FSL_USB2_UDC
 397         select IMX_HAVE_PLATFORM_GPIO_KEYS
 398         select IMX_HAVE_PLATFORM_IMX2_WDT
 399         select IMX_HAVE_PLATFORM_IMX_I2C
 400         select IMX_HAVE_PLATFORM_IMX_UART
 401         select IMX_HAVE_PLATFORM_IPU_CORE
 402         select IMX_HAVE_PLATFORM_MXC_EHCI
 403         select IMX_HAVE_PLATFORM_MXC_NAND
 404         select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX
 405         select SOC_IMX35
 406         help
 407           Include support for VPR200 platform. This includes specific
 408           configurations for the board and its peripherals.
 409
 410 endif
 411
 412 comment "Device tree only"
 413
 414 if ARCH_MULTI_V4T
 415
 416 config SOC_IMX1
 417         bool "i.MX1 support"
 418         select CPU_ARM920T
 419         select MXC_AVIC
 420         select PINCTRL_IMX1
 421         help
 422           This enables support for Freescale i.MX1 processor
 423
 424 endif
 425
 426 if ARCH_MULTI_V5
 427
 428 config SOC_IMX25
 429         bool "i.MX25 support"
 430         select ARCH_MXC_IOMUX_V3
 431         select CPU_ARM926T
 432         select MXC_AVIC
 433         select PINCTRL_IMX25
 434         help
 435           This enables support for Freescale i.MX25 processor
 436 endif
 437
 438 if ARCH_MULTI_V7
 439
 440 comment "Cortex-A platforms"
 441
 442 config SOC_IMX5
 443         bool
 444         select HAVE_IMX_SRC
 445         select MXC_TZIC
 446
 447 config  SOC_IMX50
 448         bool "i.MX50 support"
 449         select PINCTRL_IMX50
 450         select SOC_IMX5
 451
 452         help
 453           This enables support for Freescale i.MX50 processor.
 454
 455 config SOC_IMX51
 456         bool "i.MX51 support"
 457         select PINCTRL_IMX51
 458         select SOC_IMX5
 459         help
 460           This enables support for Freescale i.MX51 processor
 461
 462 config  SOC_IMX53
 463         bool "i.MX53 support"
 464         select PINCTRL_IMX53
 465         select SOC_IMX5
 466
 467         help
 468           This enables support for Freescale i.MX53 processor.
 469
 470 config SOC_IMX6
 471         bool
 472         select ARM_CPU_SUSPEND if (PM || CPU_IDLE)
 473         select ARM_ERRATA_754322
 474         select ARM_ERRATA_775420
 475         select ARM_GIC
 476         select HAVE_IMX_ANATOP
 477         select HAVE_IMX_GPC
 478         select HAVE_IMX_MMDC
 479         select HAVE_IMX_SRC
 480         select MFD_SYSCON
 481         select PL310_ERRATA_769419 if CACHE_L2X0
 482
 483 config SOC_IMX6Q
 484         bool "i.MX6 Quad/DualLite support"
 485         select ARM_ERRATA_764369 if SMP
 486         select HAVE_ARM_SCU if SMP
 487         select HAVE_ARM_TWD
 488         select PINCTRL_IMX6Q
 489         select SOC_IMX6
 490
 491         help
 492           This enables support for Freescale i.MX6 Quad processor.
 493
 494 config SOC_IMX6SL
 495         bool "i.MX6 SoloLite support"
 496         select PINCTRL_IMX6SL
 497         select SOC_IMX6
 498
 499         help
 500           This enables support for Freescale i.MX6 SoloLite processor.
 501
 502 config SOC_IMX6SLL
 503         bool "i.MX6 SoloLiteLite support"
 504         select SOC_IMX6
 505
 506         help
 507           This enables support for Freescale i.MX6 SoloLiteLite processor.
 508
 509 config SOC_IMX6SX
 510         bool "i.MX6 SoloX support"
 511         select PINCTRL_IMX6SX
 512         select SOC_IMX6
 513
 514         help
 515           This enables support for Freescale i.MX6 SoloX processor.
 516
 517 config SOC_IMX6UL
 518         bool "i.MX6 UltraLite support"
 519         select PINCTRL_IMX6UL
 520         select SOC_IMX6
 521
 522         help
 523           This enables support for Freescale i.MX6 UltraLite processor.
 524
 525 config SOC_IMX7D
 526         bool "i.MX7 Dual support"
 527         select PINCTRL_IMX7D
 528         select ARM_GIC
 529         select HAVE_ARM_ARCH_TIMER
 530         select HAVE_IMX_ANATOP
 531         select HAVE_IMX_MMDC
 532         select HAVE_IMX_SRC
 533         select IMX_GPCV2
 534         help
 535                 This enables support for Freescale i.MX7 Dual processor.
 536
 537 config SOC_LS1021A
 538         bool "Freescale LS1021A support"
 539         select ARM_GIC
 540         select HAVE_ARM_ARCH_TIMER
 541         select ZONE_DMA if ARM_LPAE
 542         help
 543           This enables support for Freescale LS1021A processor.
 544
 545 endif
 546
 547 comment "Cortex-A/Cortex-M asymmetric multiprocessing platforms"
 548
 549 if ARCH_MULTI_V7 || ARM_SINGLE_ARMV7M
 550
 551 config SOC_VF610
 552         bool "Vybrid Family VF610 support"
 553         select ARM_GIC if ARCH_MULTI_V7
 554         select PINCTRL_VF610
 555
 556         help
 557           This enables support for Freescale Vybrid VF610 processor.
 558
 559 choice
 560         prompt "Clocksource for scheduler clock"
 561         depends on SOC_VF610
 562         default VF_USE_ARM_GLOBAL_TIMER
 563
 564         config VF_USE_ARM_GLOBAL_TIMER
 565                 bool "Use ARM Global Timer"
 566                 depends on ARCH_MULTI_V7
 567                 select ARM_GLOBAL_TIMER
 568                 select CLKSRC_ARM_GLOBAL_TIMER_SCHED_CLOCK
 569                 help
 570                   Use the ARM Global Timer as clocksource
 571
 572         config VF_USE_PIT_TIMER
 573                 bool "Use PIT timer"
 574                 select VF_PIT_TIMER
 575                 help
 576                   Use SoC Periodic Interrupt Timer (PIT) as clocksource
 577
 578 endchoice
 579
 580 endif
 581
 582 source "arch/arm/mach-imx/devices/Kconfig"
 583
 584 endif