Merge drm/drm-next into drm-intel-next

[mirror_ubuntu-jammy-kernel.git] / arch / arm / mach-omap2 / omap-mpuss-lowpower.c

// SPDX-License-Identifier: GPL-2.0-only
/*
 * OMAP MPUSS low power code
 *
 * Copyright (C) 2011 Texas Instruments, Inc.
 *      Santosh Shilimkar <santosh.shilimkar@ti.com>
 *
 * OMAP4430 MPUSS mainly consists of dual Cortex-A9 with per-CPU
 * Local timer and Watchdog, GIC, SCU, PL310 L2 cache controller,
 * CPU0 and CPU1 LPRM modules.
 * CPU0, CPU1 and MPUSS each have there own power domain and
 * hence multiple low power combinations of MPUSS are possible.
 *
 * The CPU0 and CPU1 can't support Closed switch Retention (CSWR)
 * because the mode is not supported by hw constraints of dormant
 * mode. While waking up from the dormant mode, a reset  signal
 * to the Cortex-A9 processor must be asserted by the external
 * power controller.
 *
 * With architectural inputs and hardware recommendations, only
 * below modes are supported from power gain vs latency point of view.
 *
 *      CPU0            CPU1            MPUSS
 *      ----------------------------------------------
 *      ON              ON              ON
 *      ON(Inactive)    OFF             ON(Inactive)
 *      OFF             OFF             CSWR
 *      OFF             OFF             OSWR
 *      OFF             OFF             OFF(Device OFF *TBD)
 *      ----------------------------------------------
 *
 * Note: CPU0 is the master core and it is the last CPU to go down
 * and first to wake-up when MPUSS low power states are excercised
 */

#include <linux/kernel.h>
#include <linux/io.h>
#include <linux/errno.h>
#include <linux/linkage.h>
#include <linux/smp.h>

#include <asm/cacheflush.h>
#include <asm/tlbflush.h>
#include <asm/smp_scu.h>
#include <asm/suspend.h>
#include <asm/virt.h>
#include <asm/hardware/cache-l2x0.h>

#include "soc.h"
#include "common.h"
#include "omap44xx.h"
#include "omap4-sar-layout.h"
#include "pm.h"
#include "prcm_mpu44xx.h"
#include "prcm_mpu54xx.h"
#include "prminst44xx.h"
#include "prcm44xx.h"
#include "prm44xx.h"
#include "prm-regbits-44xx.h"

static void __iomem *sar_base;
static u32 old_cpu1_ns_pa_addr;

#if defined(CONFIG_PM) && defined(CONFIG_SMP)

struct omap4_cpu_pm_info {
        struct powerdomain *pwrdm;
        void __iomem *scu_sar_addr;
        void __iomem *wkup_sar_addr;
        void __iomem *l2x0_sar_addr;
};

/**
 * struct cpu_pm_ops - CPU pm operations
 * @finish_suspend:     CPU suspend finisher function pointer
 * @resume:             CPU resume function pointer
 * @scu_prepare:        CPU Snoop Control program function pointer
 * @hotplug_restart:    CPU restart function pointer
 *
 * Structure holds functions pointer for CPU low power operations like
 * suspend, resume and scu programming.
 */
struct cpu_pm_ops {
        int (*finish_suspend)(unsigned long cpu_state);
        void (*resume)(void);
        void (*scu_prepare)(unsigned int cpu_id, unsigned int cpu_state);
        void (*hotplug_restart)(void);
};

static DEFINE_PER_CPU(struct omap4_cpu_pm_info, omap4_pm_info);
static struct powerdomain *mpuss_pd;
static u32 cpu_context_offset;

static int default_finish_suspend(unsigned long cpu_state)
{
        omap_do_wfi();
        return 0;
}

static void dummy_cpu_resume(void)
{}

static void dummy_scu_prepare(unsigned int cpu_id, unsigned int cpu_state)
{}

static struct cpu_pm_ops omap_pm_ops = {
        .finish_suspend         = default_finish_suspend,
        .resume                 = dummy_cpu_resume,
        .scu_prepare            = dummy_scu_prepare,
        .hotplug_restart        = dummy_cpu_resume,
};

/*
 * Program the wakeup routine address for the CPU0 and CPU1
 * used for OFF or DORMANT wakeup.
 */
static inline void set_cpu_wakeup_addr(unsigned int cpu_id, u32 addr)
{
        struct omap4_cpu_pm_info *pm_info = &per_cpu(omap4_pm_info, cpu_id);

        if (pm_info->wkup_sar_addr)
                writel_relaxed(addr, pm_info->wkup_sar_addr);
}

/*
 * Store the SCU power status value to scratchpad memory
 */
static void scu_pwrst_prepare(unsigned int cpu_id, unsigned int cpu_state)
{
        struct omap4_cpu_pm_info *pm_info = &per_cpu(omap4_pm_info, cpu_id);
        u32 scu_pwr_st;

        switch (cpu_state) {
        case PWRDM_POWER_RET:
                scu_pwr_st = SCU_PM_DORMANT;
                break;
        case PWRDM_POWER_OFF:
                scu_pwr_st = SCU_PM_POWEROFF;
                break;
        case PWRDM_POWER_ON:
        case PWRDM_POWER_INACTIVE:
        default:
                scu_pwr_st = SCU_PM_NORMAL;
                break;
        }

        if (pm_info->scu_sar_addr)
                writel_relaxed(scu_pwr_st, pm_info->scu_sar_addr);
}

/* Helper functions for MPUSS OSWR */
static inline void mpuss_clear_prev_logic_pwrst(void)
{
        u32 reg;

        reg = omap4_prminst_read_inst_reg(OMAP4430_PRM_PARTITION,
                OMAP4430_PRM_MPU_INST, OMAP4_RM_MPU_MPU_CONTEXT_OFFSET);
        omap4_prminst_write_inst_reg(reg, OMAP4430_PRM_PARTITION,
                OMAP4430_PRM_MPU_INST, OMAP4_RM_MPU_MPU_CONTEXT_OFFSET);
}

static inline void cpu_clear_prev_logic_pwrst(unsigned int cpu_id)
{
        u32 reg;

        if (cpu_id) {
                reg = omap4_prcm_mpu_read_inst_reg(OMAP4430_PRCM_MPU_CPU1_INST,
                                        cpu_context_offset);
                omap4_prcm_mpu_write_inst_reg(reg, OMAP4430_PRCM_MPU_CPU1_INST,
                                        cpu_context_offset);
        } else {
                reg = omap4_prcm_mpu_read_inst_reg(OMAP4430_PRCM_MPU_CPU0_INST,
                                        cpu_context_offset);
                omap4_prcm_mpu_write_inst_reg(reg, OMAP4430_PRCM_MPU_CPU0_INST,
                                        cpu_context_offset);
        }
}

/*
 * Store the CPU cluster state for L2X0 low power operations.
 */
static void l2x0_pwrst_prepare(unsigned int cpu_id, unsigned int save_state)
{
        struct omap4_cpu_pm_info *pm_info = &per_cpu(omap4_pm_info, cpu_id);

        if (pm_info->l2x0_sar_addr)
                writel_relaxed(save_state, pm_info->l2x0_sar_addr);
}

/*
 * Save the L2X0 AUXCTRL and POR value to SAR memory. Its used to
 * in every restore MPUSS OFF path.
 */
#ifdef CONFIG_CACHE_L2X0
static void __init save_l2x0_context(void)
{
        void __iomem *l2x0_base = omap4_get_l2cache_base();

        if (l2x0_base && sar_base) {
                writel_relaxed(l2x0_saved_regs.aux_ctrl,
                               sar_base + L2X0_AUXCTRL_OFFSET);
                writel_relaxed(l2x0_saved_regs.prefetch_ctrl,
                               sar_base + L2X0_PREFETCH_CTRL_OFFSET);
        }
}
#else
static void __init save_l2x0_context(void)
{}
#endif

/**
 * omap4_enter_lowpower: OMAP4 MPUSS Low Power Entry Function
 * The purpose of this function is to manage low power programming
 * of OMAP4 MPUSS subsystem
 * @cpu : CPU ID
 * @power_state: Low power state.
 *
 * MPUSS states for the context save:
 * save_state =
 *      0 - Nothing lost and no need to save: MPUSS INACTIVE
 *      1 - CPUx L1 and logic lost: MPUSS CSWR
 *      2 - CPUx L1 and logic lost + GIC lost: MPUSS OSWR
 *      3 - CPUx L1 and logic lost + GIC + L2 lost: DEVICE OFF
 */
int omap4_enter_lowpower(unsigned int cpu, unsigned int power_state)
{
        struct omap4_cpu_pm_info *pm_info = &per_cpu(omap4_pm_info, cpu);
        unsigned int save_state = 0, cpu_logic_state = PWRDM_POWER_RET;

        if (omap_rev() == OMAP4430_REV_ES1_0)
                return -ENXIO;

        switch (power_state) {
        case PWRDM_POWER_ON:
        case PWRDM_POWER_INACTIVE:
                save_state = 0;
                break;
        case PWRDM_POWER_OFF:
                cpu_logic_state = PWRDM_POWER_OFF;
                save_state = 1;
                break;
        case PWRDM_POWER_RET:
                if (IS_PM44XX_ERRATUM(PM_OMAP4_CPU_OSWR_DISABLE))
                        save_state = 0;
                break;
        default:
                /*
                 * CPUx CSWR is invalid hardware state. Also CPUx OSWR
                 * doesn't make much scense, since logic is lost and $L1
                 * needs to be cleaned because of coherency. This makes
                 * CPUx OSWR equivalent to CPUX OFF and hence not supported
                 */
                WARN_ON(1);
                return -ENXIO;
        }

        pwrdm_pre_transition(NULL);

        /*
         * Check MPUSS next state and save interrupt controller if needed.
         * In MPUSS OSWR or device OFF, interrupt controller  contest is lost.
         */
        mpuss_clear_prev_logic_pwrst();
        if ((pwrdm_read_next_pwrst(mpuss_pd) == PWRDM_POWER_RET) &&
                (pwrdm_read_logic_retst(mpuss_pd) == PWRDM_POWER_OFF))
                save_state = 2;

        cpu_clear_prev_logic_pwrst(cpu);
        pwrdm_set_next_pwrst(pm_info->pwrdm, power_state);
        pwrdm_set_logic_retst(pm_info->pwrdm, cpu_logic_state);
        set_cpu_wakeup_addr(cpu, __pa_symbol(omap_pm_ops.resume));
        omap_pm_ops.scu_prepare(cpu, power_state);
        l2x0_pwrst_prepare(cpu, save_state);

        /*
         * Call low level function  with targeted low power state.
         */
        if (save_state)
                cpu_suspend(save_state, omap_pm_ops.finish_suspend);
        else
                omap_pm_ops.finish_suspend(save_state);

        if (IS_PM44XX_ERRATUM(PM_OMAP4_ROM_SMP_BOOT_ERRATUM_GICD) && cpu)
                gic_dist_enable();

        /*
         * Restore the CPUx power state to ON otherwise CPUx
         * power domain can transitions to programmed low power
         * state while doing WFI outside the low powe code. On
         * secure devices, CPUx does WFI which can result in
         * domain transition
         */
        pwrdm_set_next_pwrst(pm_info->pwrdm, PWRDM_POWER_ON);

        pwrdm_post_transition(NULL);

        return 0;
}

/**
 * omap4_hotplug_cpu: OMAP4 CPU hotplug entry
 * @cpu : CPU ID
 * @power_state: CPU low power state.
 */
int omap4_hotplug_cpu(unsigned int cpu, unsigned int power_state)
{
        struct omap4_cpu_pm_info *pm_info = &per_cpu(omap4_pm_info, cpu);
        unsigned int cpu_state = 0;

        if (omap_rev() == OMAP4430_REV_ES1_0)
                return -ENXIO;

        /* Use the achievable power state for the domain */
        power_state = pwrdm_get_valid_lp_state(pm_info->pwrdm,
                                               false, power_state);

        if (power_state == PWRDM_POWER_OFF)
                cpu_state = 1;

        pwrdm_clear_all_prev_pwrst(pm_info->pwrdm);
        pwrdm_set_next_pwrst(pm_info->pwrdm, power_state);
        set_cpu_wakeup_addr(cpu, __pa_symbol(omap_pm_ops.hotplug_restart));
        omap_pm_ops.scu_prepare(cpu, power_state);

        /*
         * CPU never retuns back if targeted power state is OFF mode.
         * CPU ONLINE follows normal CPU ONLINE ptah via
         * omap4_secondary_startup().
         */
        omap_pm_ops.finish_suspend(cpu_state);

        pwrdm_set_next_pwrst(pm_info->pwrdm, PWRDM_POWER_ON);
        return 0;
}


/*
 * Enable Mercury Fast HG retention mode by default.
 */
static void enable_mercury_retention_mode(void)
{
        u32 reg;

        reg = omap4_prcm_mpu_read_inst_reg(OMAP54XX_PRCM_MPU_DEVICE_INST,
                                  OMAP54XX_PRCM_MPU_PRM_PSCON_COUNT_OFFSET);
        /* Enable HG_EN, HG_RAMPUP = fast mode */
        reg |= BIT(24) | BIT(25);
        omap4_prcm_mpu_write_inst_reg(reg, OMAP54XX_PRCM_MPU_DEVICE_INST,
                                      OMAP54XX_PRCM_MPU_PRM_PSCON_COUNT_OFFSET);
}

/*
 * Initialise OMAP4 MPUSS
 */
int __init omap4_mpuss_init(void)
{
        struct omap4_cpu_pm_info *pm_info;

        if (omap_rev() == OMAP4430_REV_ES1_0) {
                WARN(1, "Power Management not supported on OMAP4430 ES1.0\n");
                return -ENODEV;
        }

        /* Initilaise per CPU PM information */
        pm_info = &per_cpu(omap4_pm_info, 0x0);
        if (sar_base) {
                pm_info->scu_sar_addr = sar_base + SCU_OFFSET0;
                if (cpu_is_omap44xx())
                        pm_info->wkup_sar_addr = sar_base +
                                CPU0_WAKEUP_NS_PA_ADDR_OFFSET;
                else
                        pm_info->wkup_sar_addr = sar_base +
                                OMAP5_CPU0_WAKEUP_NS_PA_ADDR_OFFSET;
                pm_info->l2x0_sar_addr = sar_base + L2X0_SAVE_OFFSET0;
        }
        pm_info->pwrdm = pwrdm_lookup("cpu0_pwrdm");
        if (!pm_info->pwrdm) {
                pr_err("Lookup failed for CPU0 pwrdm\n");
                return -ENODEV;
        }

        /* Clear CPU previous power domain state */
        pwrdm_clear_all_prev_pwrst(pm_info->pwrdm);
        cpu_clear_prev_logic_pwrst(0);

        /* Initialise CPU0 power domain state to ON */
        pwrdm_set_next_pwrst(pm_info->pwrdm, PWRDM_POWER_ON);

        pm_info = &per_cpu(omap4_pm_info, 0x1);
        if (sar_base) {
                pm_info->scu_sar_addr = sar_base + SCU_OFFSET1;
                if (cpu_is_omap44xx())
                        pm_info->wkup_sar_addr = sar_base +
                                CPU1_WAKEUP_NS_PA_ADDR_OFFSET;
                else
                        pm_info->wkup_sar_addr = sar_base +
                                OMAP5_CPU1_WAKEUP_NS_PA_ADDR_OFFSET;
                pm_info->l2x0_sar_addr = sar_base + L2X0_SAVE_OFFSET1;
        }

        pm_info->pwrdm = pwrdm_lookup("cpu1_pwrdm");
        if (!pm_info->pwrdm) {
                pr_err("Lookup failed for CPU1 pwrdm\n");
                return -ENODEV;
        }

        /* Clear CPU previous power domain state */
        pwrdm_clear_all_prev_pwrst(pm_info->pwrdm);
        cpu_clear_prev_logic_pwrst(1);

        /* Initialise CPU1 power domain state to ON */
        pwrdm_set_next_pwrst(pm_info->pwrdm, PWRDM_POWER_ON);

        mpuss_pd = pwrdm_lookup("mpu_pwrdm");
        if (!mpuss_pd) {
                pr_err("Failed to lookup MPUSS power domain\n");
                return -ENODEV;
        }
        pwrdm_clear_all_prev_pwrst(mpuss_pd);
        mpuss_clear_prev_logic_pwrst();

        if (sar_base) {
                /* Save device type on scratchpad for low level code to use */
                writel_relaxed((omap_type() != OMAP2_DEVICE_TYPE_GP) ? 1 : 0,
                               sar_base + OMAP_TYPE_OFFSET);
                save_l2x0_context();
        }

        if (cpu_is_omap44xx()) {
                omap_pm_ops.finish_suspend = omap4_finish_suspend;
                omap_pm_ops.resume = omap4_cpu_resume;
                omap_pm_ops.scu_prepare = scu_pwrst_prepare;
                omap_pm_ops.hotplug_restart = omap4_secondary_startup;
                cpu_context_offset = OMAP4_RM_CPU0_CPU0_CONTEXT_OFFSET;
        } else if (soc_is_omap54xx() || soc_is_dra7xx()) {
                cpu_context_offset = OMAP54XX_RM_CPU0_CPU0_CONTEXT_OFFSET;
                enable_mercury_retention_mode();
        }

        if (cpu_is_omap446x())
                omap_pm_ops.hotplug_restart = omap4460_secondary_startup;

        return 0;
}

#endif

u32 omap4_get_cpu1_ns_pa_addr(void)
{
        return old_cpu1_ns_pa_addr;
}

/*
 * For kexec, we must set CPU1_WAKEUP_NS_PA_ADDR to point to
 * current kernel's secondary_startup() early before
 * clockdomains_init(). Otherwise clockdomain_init() can
 * wake CPU1 and cause a hang.
 */
void __init omap4_mpuss_early_init(void)
{
        unsigned long startup_pa;
        void __iomem *ns_pa_addr;

        if (!(soc_is_omap44xx() || soc_is_omap54xx()))
                return;

        sar_base = omap4_get_sar_ram_base();

        /* Save old NS_PA_ADDR for validity checks later on */
        if (soc_is_omap44xx())
                ns_pa_addr = sar_base + CPU1_WAKEUP_NS_PA_ADDR_OFFSET;
        else
                ns_pa_addr = sar_base + OMAP5_CPU1_WAKEUP_NS_PA_ADDR_OFFSET;
        old_cpu1_ns_pa_addr = readl_relaxed(ns_pa_addr);

        if (soc_is_omap443x())
                startup_pa = __pa_symbol(omap4_secondary_startup);
        else if (soc_is_omap446x())
                startup_pa = __pa_symbol(omap4460_secondary_startup);
        else if ((__boot_cpu_mode & MODE_MASK) == HYP_MODE)
                startup_pa = __pa_symbol(omap5_secondary_hyp_startup);
        else
                startup_pa = __pa_symbol(omap5_secondary_startup);

        if (soc_is_omap44xx())
                writel_relaxed(startup_pa, sar_base +
                               CPU1_WAKEUP_NS_PA_ADDR_OFFSET);
        else
                writel_relaxed(startup_pa, sar_base +
                               OMAP5_CPU1_WAKEUP_NS_PA_ADDR_OFFSET);
}