]> git.proxmox.com Git - mirror_ubuntu-zesty-kernel.git/blob - drivers/cpufreq/gx-suspmod.c
Merge branch 'drm-dwhdmi-devel' of git://ftp.arm.linux.org.uk/~rmk/linux-arm into...
[mirror_ubuntu-zesty-kernel.git] / drivers / cpufreq / gx-suspmod.c
1 /*
2 * Cyrix MediaGX and NatSemi Geode Suspend Modulation
3 * (C) 2002 Zwane Mwaikambo <zwane@commfireservices.com>
4 * (C) 2002 Hiroshi Miura <miura@da-cha.org>
5 * All Rights Reserved
6 *
7 * This program is free software; you can redistribute it and/or
8 * modify it under the terms of the GNU General Public License
9 * version 2 as published by the Free Software Foundation
10 *
11 * The author(s) of this software shall not be held liable for damages
12 * of any nature resulting due to the use of this software. This
13 * software is provided AS-IS with no warranties.
14 *
15 * Theoretical note:
16 *
17 * (see Geode(tm) CS5530 manual (rev.4.1) page.56)
18 *
19 * CPU frequency control on NatSemi Geode GX1/GXLV processor and CS55x0
20 * are based on Suspend Modulation.
21 *
22 * Suspend Modulation works by asserting and de-asserting the SUSP# pin
23 * to CPU(GX1/GXLV) for configurable durations. When asserting SUSP#
24 * the CPU enters an idle state. GX1 stops its core clock when SUSP# is
25 * asserted then power consumption is reduced.
26 *
27 * Suspend Modulation's OFF/ON duration are configurable
28 * with 'Suspend Modulation OFF Count Register'
29 * and 'Suspend Modulation ON Count Register'.
30 * These registers are 8bit counters that represent the number of
31 * 32us intervals which the SUSP# pin is asserted(ON)/de-asserted(OFF)
32 * to the processor.
33 *
34 * These counters define a ratio which is the effective frequency
35 * of operation of the system.
36 *
37 * OFF Count
38 * F_eff = Fgx * ----------------------
39 * OFF Count + ON Count
40 *
41 * 0 <= On Count, Off Count <= 255
42 *
43 * From these limits, we can get register values
44 *
45 * off_duration + on_duration <= MAX_DURATION
46 * on_duration = off_duration * (stock_freq - freq) / freq
47 *
48 * off_duration = (freq * DURATION) / stock_freq
49 * on_duration = DURATION - off_duration
50 *
51 *
52 *---------------------------------------------------------------------------
53 *
54 * ChangeLog:
55 * Dec. 12, 2003 Hiroshi Miura <miura@da-cha.org>
56 * - fix on/off register mistake
57 * - fix cpu_khz calc when it stops cpu modulation.
58 *
59 * Dec. 11, 2002 Hiroshi Miura <miura@da-cha.org>
60 * - rewrite for Cyrix MediaGX Cx5510/5520 and
61 * NatSemi Geode Cs5530(A).
62 *
63 * Jul. ??, 2002 Zwane Mwaikambo <zwane@commfireservices.com>
64 * - cs5530_mod patch for 2.4.19-rc1.
65 *
66 *---------------------------------------------------------------------------
67 *
68 * Todo
69 * Test on machines with 5510, 5530, 5530A
70 */
71
72 /************************************************************************
73 * Suspend Modulation - Definitions *
74 ************************************************************************/
75
76 #include <linux/kernel.h>
77 #include <linux/module.h>
78 #include <linux/init.h>
79 #include <linux/smp.h>
80 #include <linux/cpufreq.h>
81 #include <linux/pci.h>
82 #include <linux/errno.h>
83 #include <linux/slab.h>
84
85 #include <asm/cpu_device_id.h>
86 #include <asm/processor-cyrix.h>
87
88 /* PCI config registers, all at F0 */
89 #define PCI_PMER1 0x80 /* power management enable register 1 */
90 #define PCI_PMER2 0x81 /* power management enable register 2 */
91 #define PCI_PMER3 0x82 /* power management enable register 3 */
92 #define PCI_IRQTC 0x8c /* irq speedup timer counter register:typical 2 to 4ms */
93 #define PCI_VIDTC 0x8d /* video speedup timer counter register: typical 50 to 100ms */
94 #define PCI_MODOFF 0x94 /* suspend modulation OFF counter register, 1 = 32us */
95 #define PCI_MODON 0x95 /* suspend modulation ON counter register */
96 #define PCI_SUSCFG 0x96 /* suspend configuration register */
97
98 /* PMER1 bits */
99 #define GPM (1<<0) /* global power management */
100 #define GIT (1<<1) /* globally enable PM device idle timers */
101 #define GTR (1<<2) /* globally enable IO traps */
102 #define IRQ_SPDUP (1<<3) /* disable clock throttle during interrupt handling */
103 #define VID_SPDUP (1<<4) /* disable clock throttle during vga video handling */
104
105 /* SUSCFG bits */
106 #define SUSMOD (1<<0) /* enable/disable suspend modulation */
107 /* the below is supported only with cs5530 (after rev.1.2)/cs5530A */
108 #define SMISPDUP (1<<1) /* select how SMI re-enable suspend modulation: */
109 /* IRQTC timer or read SMI speedup disable reg.(F1BAR[08-09h]) */
110 #define SUSCFG (1<<2) /* enable powering down a GXLV processor. "Special 3Volt Suspend" mode */
111 /* the below is supported only with cs5530A */
112 #define PWRSVE_ISA (1<<3) /* stop ISA clock */
113 #define PWRSVE (1<<4) /* active idle */
114
115 struct gxfreq_params {
116 u8 on_duration;
117 u8 off_duration;
118 u8 pci_suscfg;
119 u8 pci_pmer1;
120 u8 pci_pmer2;
121 struct pci_dev *cs55x0;
122 };
123
124 static struct gxfreq_params *gx_params;
125 static int stock_freq;
126
127 /* PCI bus clock - defaults to 30.000 if cpu_khz is not available */
128 static int pci_busclk;
129 module_param(pci_busclk, int, 0444);
130
131 /* maximum duration for which the cpu may be suspended
132 * (32us * MAX_DURATION). If no parameter is given, this defaults
133 * to 255.
134 * Note that this leads to a maximum of 8 ms(!) where the CPU clock
135 * is suspended -- processing power is just 0.39% of what it used to be,
136 * though. 781.25 kHz(!) for a 200 MHz processor -- wow. */
137 static int max_duration = 255;
138 module_param(max_duration, int, 0444);
139
140 /* For the default policy, we want at least some processing power
141 * - let's say 5%. (min = maxfreq / POLICY_MIN_DIV)
142 */
143 #define POLICY_MIN_DIV 20
144
145
146 /**
147 * we can detect a core multiplier from dir0_lsb
148 * from GX1 datasheet p.56,
149 * MULT[3:0]:
150 * 0000 = SYSCLK multiplied by 4 (test only)
151 * 0001 = SYSCLK multiplied by 10
152 * 0010 = SYSCLK multiplied by 4
153 * 0011 = SYSCLK multiplied by 6
154 * 0100 = SYSCLK multiplied by 9
155 * 0101 = SYSCLK multiplied by 5
156 * 0110 = SYSCLK multiplied by 7
157 * 0111 = SYSCLK multiplied by 8
158 * of 33.3MHz
159 **/
160 static int gx_freq_mult[16] = {
161 4, 10, 4, 6, 9, 5, 7, 8,
162 0, 0, 0, 0, 0, 0, 0, 0
163 };
164
165
166 /****************************************************************
167 * Low Level chipset interface *
168 ****************************************************************/
169 static struct pci_device_id gx_chipset_tbl[] __initdata = {
170 { PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5530_LEGACY), },
171 { PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5520), },
172 { PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5510), },
173 { 0, },
174 };
175 MODULE_DEVICE_TABLE(pci, gx_chipset_tbl);
176
177 static void gx_write_byte(int reg, int value)
178 {
179 pci_write_config_byte(gx_params->cs55x0, reg, value);
180 }
181
182 /**
183 * gx_detect_chipset:
184 *
185 **/
186 static struct pci_dev * __init gx_detect_chipset(void)
187 {
188 struct pci_dev *gx_pci = NULL;
189
190 /* detect which companion chip is used */
191 for_each_pci_dev(gx_pci) {
192 if ((pci_match_id(gx_chipset_tbl, gx_pci)) != NULL)
193 return gx_pci;
194 }
195
196 pr_debug("error: no supported chipset found!\n");
197 return NULL;
198 }
199
200 /**
201 * gx_get_cpuspeed:
202 *
203 * Finds out at which efficient frequency the Cyrix MediaGX/NatSemi
204 * Geode CPU runs.
205 */
206 static unsigned int gx_get_cpuspeed(unsigned int cpu)
207 {
208 if ((gx_params->pci_suscfg & SUSMOD) == 0)
209 return stock_freq;
210
211 return (stock_freq * gx_params->off_duration)
212 / (gx_params->on_duration + gx_params->off_duration);
213 }
214
215 /**
216 * gx_validate_speed:
217 * determine current cpu speed
218 *
219 **/
220
221 static unsigned int gx_validate_speed(unsigned int khz, u8 *on_duration,
222 u8 *off_duration)
223 {
224 unsigned int i;
225 u8 tmp_on, tmp_off;
226 int old_tmp_freq = stock_freq;
227 int tmp_freq;
228
229 *off_duration = 1;
230 *on_duration = 0;
231
232 for (i = max_duration; i > 0; i--) {
233 tmp_off = ((khz * i) / stock_freq) & 0xff;
234 tmp_on = i - tmp_off;
235 tmp_freq = (stock_freq * tmp_off) / i;
236 /* if this relation is closer to khz, use this. If it's equal,
237 * prefer it, too - lower latency */
238 if (abs(tmp_freq - khz) <= abs(old_tmp_freq - khz)) {
239 *on_duration = tmp_on;
240 *off_duration = tmp_off;
241 old_tmp_freq = tmp_freq;
242 }
243 }
244
245 return old_tmp_freq;
246 }
247
248
249 /**
250 * gx_set_cpuspeed:
251 * set cpu speed in khz.
252 **/
253
254 static void gx_set_cpuspeed(struct cpufreq_policy *policy, unsigned int khz)
255 {
256 u8 suscfg, pmer1;
257 unsigned int new_khz;
258 unsigned long flags;
259 struct cpufreq_freqs freqs;
260
261 freqs.old = gx_get_cpuspeed(0);
262
263 new_khz = gx_validate_speed(khz, &gx_params->on_duration,
264 &gx_params->off_duration);
265
266 freqs.new = new_khz;
267
268 cpufreq_freq_transition_begin(policy, &freqs);
269 local_irq_save(flags);
270
271 if (new_khz != stock_freq) {
272 /* if new khz == 100% of CPU speed, it is special case */
273 switch (gx_params->cs55x0->device) {
274 case PCI_DEVICE_ID_CYRIX_5530_LEGACY:
275 pmer1 = gx_params->pci_pmer1 | IRQ_SPDUP | VID_SPDUP;
276 /* FIXME: need to test other values -- Zwane,Miura */
277 /* typical 2 to 4ms */
278 gx_write_byte(PCI_IRQTC, 4);
279 /* typical 50 to 100ms */
280 gx_write_byte(PCI_VIDTC, 100);
281 gx_write_byte(PCI_PMER1, pmer1);
282
283 if (gx_params->cs55x0->revision < 0x10) {
284 /* CS5530(rev 1.2, 1.3) */
285 suscfg = gx_params->pci_suscfg|SUSMOD;
286 } else {
287 /* CS5530A,B.. */
288 suscfg = gx_params->pci_suscfg|SUSMOD|PWRSVE;
289 }
290 break;
291 case PCI_DEVICE_ID_CYRIX_5520:
292 case PCI_DEVICE_ID_CYRIX_5510:
293 suscfg = gx_params->pci_suscfg | SUSMOD;
294 break;
295 default:
296 local_irq_restore(flags);
297 pr_debug("fatal: try to set unknown chipset.\n");
298 return;
299 }
300 } else {
301 suscfg = gx_params->pci_suscfg & ~(SUSMOD);
302 gx_params->off_duration = 0;
303 gx_params->on_duration = 0;
304 pr_debug("suspend modulation disabled: cpu runs 100%% speed.\n");
305 }
306
307 gx_write_byte(PCI_MODOFF, gx_params->off_duration);
308 gx_write_byte(PCI_MODON, gx_params->on_duration);
309
310 gx_write_byte(PCI_SUSCFG, suscfg);
311 pci_read_config_byte(gx_params->cs55x0, PCI_SUSCFG, &suscfg);
312
313 local_irq_restore(flags);
314
315 gx_params->pci_suscfg = suscfg;
316
317 cpufreq_freq_transition_end(policy, &freqs, 0);
318
319 pr_debug("suspend modulation w/ duration of ON:%d us, OFF:%d us\n",
320 gx_params->on_duration * 32, gx_params->off_duration * 32);
321 pr_debug("suspend modulation w/ clock speed: %d kHz.\n", freqs.new);
322 }
323
324 /****************************************************************
325 * High level functions *
326 ****************************************************************/
327
328 /*
329 * cpufreq_gx_verify: test if frequency range is valid
330 *
331 * This function checks if a given frequency range in kHz is valid
332 * for the hardware supported by the driver.
333 */
334
335 static int cpufreq_gx_verify(struct cpufreq_policy *policy)
336 {
337 unsigned int tmp_freq = 0;
338 u8 tmp1, tmp2;
339
340 if (!stock_freq || !policy)
341 return -EINVAL;
342
343 policy->cpu = 0;
344 cpufreq_verify_within_limits(policy, (stock_freq / max_duration),
345 stock_freq);
346
347 /* it needs to be assured that at least one supported frequency is
348 * within policy->min and policy->max. If it is not, policy->max
349 * needs to be increased until one frequency is supported.
350 * policy->min may not be decreased, though. This way we guarantee a
351 * specific processing capacity.
352 */
353 tmp_freq = gx_validate_speed(policy->min, &tmp1, &tmp2);
354 if (tmp_freq < policy->min)
355 tmp_freq += stock_freq / max_duration;
356 policy->min = tmp_freq;
357 if (policy->min > policy->max)
358 policy->max = tmp_freq;
359 tmp_freq = gx_validate_speed(policy->max, &tmp1, &tmp2);
360 if (tmp_freq > policy->max)
361 tmp_freq -= stock_freq / max_duration;
362 policy->max = tmp_freq;
363 if (policy->max < policy->min)
364 policy->max = policy->min;
365 cpufreq_verify_within_limits(policy, (stock_freq / max_duration),
366 stock_freq);
367
368 return 0;
369 }
370
371 /*
372 * cpufreq_gx_target:
373 *
374 */
375 static int cpufreq_gx_target(struct cpufreq_policy *policy,
376 unsigned int target_freq,
377 unsigned int relation)
378 {
379 u8 tmp1, tmp2;
380 unsigned int tmp_freq;
381
382 if (!stock_freq || !policy)
383 return -EINVAL;
384
385 policy->cpu = 0;
386
387 tmp_freq = gx_validate_speed(target_freq, &tmp1, &tmp2);
388 while (tmp_freq < policy->min) {
389 tmp_freq += stock_freq / max_duration;
390 tmp_freq = gx_validate_speed(tmp_freq, &tmp1, &tmp2);
391 }
392 while (tmp_freq > policy->max) {
393 tmp_freq -= stock_freq / max_duration;
394 tmp_freq = gx_validate_speed(tmp_freq, &tmp1, &tmp2);
395 }
396
397 gx_set_cpuspeed(policy, tmp_freq);
398
399 return 0;
400 }
401
402 static int cpufreq_gx_cpu_init(struct cpufreq_policy *policy)
403 {
404 unsigned int maxfreq;
405
406 if (!policy || policy->cpu != 0)
407 return -ENODEV;
408
409 /* determine maximum frequency */
410 if (pci_busclk)
411 maxfreq = pci_busclk * gx_freq_mult[getCx86(CX86_DIR1) & 0x0f];
412 else if (cpu_khz)
413 maxfreq = cpu_khz;
414 else
415 maxfreq = 30000 * gx_freq_mult[getCx86(CX86_DIR1) & 0x0f];
416
417 stock_freq = maxfreq;
418
419 pr_debug("cpu max frequency is %d.\n", maxfreq);
420
421 /* setup basic struct for cpufreq API */
422 policy->cpu = 0;
423
424 if (max_duration < POLICY_MIN_DIV)
425 policy->min = maxfreq / max_duration;
426 else
427 policy->min = maxfreq / POLICY_MIN_DIV;
428 policy->max = maxfreq;
429 policy->cpuinfo.min_freq = maxfreq / max_duration;
430 policy->cpuinfo.max_freq = maxfreq;
431 policy->cpuinfo.transition_latency = CPUFREQ_ETERNAL;
432
433 return 0;
434 }
435
436 /*
437 * cpufreq_gx_init:
438 * MediaGX/Geode GX initialize cpufreq driver
439 */
440 static struct cpufreq_driver gx_suspmod_driver = {
441 .get = gx_get_cpuspeed,
442 .verify = cpufreq_gx_verify,
443 .target = cpufreq_gx_target,
444 .init = cpufreq_gx_cpu_init,
445 .name = "gx-suspmod",
446 };
447
448 static int __init cpufreq_gx_init(void)
449 {
450 int ret;
451 struct gxfreq_params *params;
452 struct pci_dev *gx_pci;
453
454 /* Test if we have the right hardware */
455 gx_pci = gx_detect_chipset();
456 if (gx_pci == NULL)
457 return -ENODEV;
458
459 /* check whether module parameters are sane */
460 if (max_duration > 0xff)
461 max_duration = 0xff;
462
463 pr_debug("geode suspend modulation available.\n");
464
465 params = kzalloc(sizeof(*params), GFP_KERNEL);
466 if (params == NULL)
467 return -ENOMEM;
468
469 params->cs55x0 = gx_pci;
470 gx_params = params;
471
472 /* keep cs55x0 configurations */
473 pci_read_config_byte(params->cs55x0, PCI_SUSCFG, &(params->pci_suscfg));
474 pci_read_config_byte(params->cs55x0, PCI_PMER1, &(params->pci_pmer1));
475 pci_read_config_byte(params->cs55x0, PCI_PMER2, &(params->pci_pmer2));
476 pci_read_config_byte(params->cs55x0, PCI_MODON, &(params->on_duration));
477 pci_read_config_byte(params->cs55x0, PCI_MODOFF,
478 &(params->off_duration));
479
480 ret = cpufreq_register_driver(&gx_suspmod_driver);
481 if (ret) {
482 kfree(params);
483 return ret; /* register error! */
484 }
485
486 return 0;
487 }
488
489 static void __exit cpufreq_gx_exit(void)
490 {
491 cpufreq_unregister_driver(&gx_suspmod_driver);
492 pci_dev_put(gx_params->cs55x0);
493 kfree(gx_params);
494 }
495
496 MODULE_AUTHOR("Hiroshi Miura <miura@da-cha.org>");
497 MODULE_DESCRIPTION("Cpufreq driver for Cyrix MediaGX and NatSemi Geode");
498 MODULE_LICENSE("GPL");
499
500 module_init(cpufreq_gx_init);
501 module_exit(cpufreq_gx_exit);
502