drivers/fc4/Kconfig

   1 #
   2 # FC4 device configuration
   3 #
   4
   5 menu "Fibre Channel support"
   6
   7 config FC4
   8         tristate "Fibre Channel and FC4 SCSI support"
   9         ---help---
  10           Fibre Channel is a high speed serial protocol mainly used to
  11           connect large storage devices to the computer; it is compatible with
  12           and intended to replace SCSI.
  13
  14           This is an experimental support for storage arrays connected to your
  15           computer using optical fibre cables and the "X3.269-199X Fibre
  16           Channel Protocol for SCSI" specification. If you want to use this,
  17           you need to say Y here and to "SCSI support" as well as to the
  18           drivers for the storage array itself and for the interface adapter
  19           such as SOC or SOC+. This subsystem could even serve for IP
  20           networking, with some code extensions.
  21
  22           If unsure, say N.
  23
  24 comment "FC4 drivers"
  25         depends on FC4
  26
  27 config FC4_SOC
  28         tristate "Sun SOC/Sbus"
  29         depends on FC4!=n && (SPARC32 || SPARC64)
  30         help
  31           Serial Optical Channel is an interface card with one or two Fibre
  32           Optic ports, each of which can be connected to a disk array. Note
  33           that if you have older firmware in the card, you'll need the
  34           microcode from the Solaris driver to make it work.
  35
  36           To compile this support as a module, choose M here: the module will
  37           be called soc.
  38
  39 config FC4_SOCAL
  40         tristate "Sun SOC+ (aka SOCAL)"
  41         depends on FC4!=n && (SPARC32 || SPARC64)
  42         ---help---
  43           Serial Optical Channel Plus is an interface card with up to two
  44           Fibre Optic ports. This card supports FC Arbitrated Loop (usually
  45           A5000 or internal FC disks in E[3-6]000 machines through the
  46           Interface Board). You'll probably need the microcode from the
  47           Solaris driver to make it work.
  48
  49           To compile this support as a module, choose M here: the module will
  50           be called socal.
  51
  52 comment "FC4 targets"
  53         depends on FC4
  54
  55 config SCSI_PLUTO
  56         tristate "SparcSTORAGE Array 100 and 200 series"
  57         depends on FC4!=n && SCSI
  58         help
  59           If you never bought a disk array made by Sun, go with N.
  60
  61           To compile this support as a module, choose M here: the module will
  62           be called pluto.
  63
  64 config SCSI_FCAL
  65         tristate "Sun Enterprise Network Array (A5000 and EX500)" if SPARC32 || SPARC64
  66         depends on FC4!=n && SCSI
  67         help
  68           This driver drives FC-AL disks connected through a Fibre Channel
  69           card using the drivers/fc4 layer (currently only SOCAL). The most
  70           common is either A5000 array or internal disks in E[3-6]000
  71           machines.
  72
  73           To compile this support as a module, choose M here: the module will
  74           be called fcal.
  75
  76 config SCSI_FCAL
  77         prompt "Generic FC-AL disk driver"
  78         depends on FC4!=n && SCSI && !SPARC32 && !SPARC64
  79
  80 endmenu
  81