drivers/fsi/Kconfig

   1 # SPDX-License-Identifier: GPL-2.0-only
   2 #
   3 # FSI subsystem
   4 #
   5
   6 menuconfig FSI
   7         tristate "FSI support"
   8         depends on OF
   9         select CRC4
  10         help
  11           FSI - the FRU Support Interface - is a simple bus for low-level
  12           access to POWER-based hardware.
  13
  14 if FSI
  15
  16 config FSI_NEW_DEV_NODE
  17         bool "Create '/dev/fsi' directory for char devices"
  18         default n
  19         help
  20         This option causes char devices created for FSI devices to be
  21         located under a common /dev/fsi/ directory. Set to N unless your
  22         userspace has been updated to handle the new location.
  23
  24         Additionally, it also causes the char device names to be offset
  25         by one so that chip 0 will have /dev/scom1 and chip1 /dev/scom2
  26         to match old userspace expectations.
  27
  28         New userspace will use udev rules to generate predictable access
  29         symlinks in /dev/fsi/by-path when this option is enabled.
  30
  31 config FSI_MASTER_GPIO
  32         tristate "GPIO-based FSI master"
  33         depends on GPIOLIB
  34         select CRC4
  35         help
  36         This option enables a FSI master driver using GPIO lines.
  37
  38 config FSI_MASTER_HUB
  39         tristate "FSI hub master"
  40         help
  41         This option enables a FSI hub master driver.  Hub is a type of FSI
  42         master that is connected to the upstream master via a slave.  Hubs
  43         allow chaining of FSI links to an arbitrary depth.  This allows for
  44         a high target device fanout.
  45
  46 config FSI_MASTER_AST_CF
  47         tristate "FSI master based on Aspeed ColdFire coprocessor"
  48         depends on GPIOLIB
  49         depends on GPIO_ASPEED
  50         select GENERIC_ALLOCATOR
  51         help
  52         This option enables a FSI master using the AST2400 and AST2500 GPIO
  53         lines driven by the internal ColdFire coprocessor. This requires
  54         the corresponding machine specific ColdFire firmware to be available.
  55
  56 config FSI_MASTER_ASPEED
  57         tristate "FSI ASPEED master"
  58         depends on HAS_IOMEM
  59         help
  60          This option enables a FSI master that is present behind an OPB bridge
  61          in the AST2600.
  62
  63          Enable it for your BMC kernel in an OpenPower or IBM Power system.
  64
  65 config FSI_SCOM
  66         tristate "SCOM FSI client device driver"
  67         help
  68         This option enables an FSI based SCOM device driver.
  69
  70 config FSI_SBEFIFO
  71         tristate "SBEFIFO FSI client device driver"
  72         depends on OF_ADDRESS
  73         help
  74         This option enables an FSI based SBEFIFO device driver. The SBEFIFO is
  75         a pipe-like FSI device for communicating with the self boot engine
  76         (SBE) on POWER processors.
  77
  78 config FSI_OCC
  79         tristate "OCC SBEFIFO client device driver"
  80         depends on FSI_SBEFIFO
  81         help
  82         This option enables an SBEFIFO based On-Chip Controller (OCC) device
  83         driver. The OCC is a device embedded on a POWER processor that collects
  84         and aggregates sensor data from the processor and system. The OCC can
  85         provide the raw sensor data as well as perform thermal and power
  86         management on the system.
  87
  88 endif