drivers/ide/Kconfig

   1 #
   2 # IDE ATA ATAPI Block device driver configuration
   3 #
   4
   5 # Select HAVE_IDE if IDE is supported
   6 config HAVE_IDE
   7         bool
   8
   9 menuconfig IDE
  10         tristate "ATA/ATAPI/MFM/RLL support (DEPRECATED)"
  11         depends on HAVE_IDE
  12         depends on BLOCK
  13         ---help---
  14           If you say Y here, your kernel will be able to manage ATA/(E)IDE and
  15           ATAPI units. The most common cases are IDE hard drives and ATAPI
  16           CD-ROM drives.
  17
  18           This subsystem is currently in maintenance mode with only bug fix
  19           changes applied. Users of ATA hardware are encouraged to migrate to
  20           the newer ATA subsystem ("Serial ATA (prod) and Parallel ATA
  21           (experimental) drivers") which is more actively maintained.
  22
  23           To compile this driver as a module, choose M here: the
  24           module will be called ide-core.
  25
  26           For further information, please read <file:Documentation/ide/ide.txt>.
  27
  28           If unsure, say N.
  29
  30 if IDE
  31
  32 comment "Please see Documentation/ide/ide.txt for help/info on IDE drives"
  33
  34 config IDE_XFER_MODE
  35         bool
  36
  37 config IDE_TIMINGS
  38         bool
  39         select IDE_XFER_MODE
  40
  41 config IDE_ATAPI
  42         bool
  43
  44 config IDE_LEGACY
  45         bool
  46
  47 config BLK_DEV_IDE_SATA
  48         bool "Support for SATA (deprecated; conflicts with libata SATA driver)"
  49         default n
  50         ---help---
  51           There are two drivers for Serial ATA controllers.
  52
  53           The main driver, "libata", uses the SCSI subsystem
  54           and supports most modern SATA controllers. In order to use it
  55           you may take a look at "Serial ATA (prod) and Parallel ATA
  56           (experimental) drivers".
  57
  58           The IDE driver (which you are currently configuring) supports
  59           a few first-generation SATA controllers.
  60
  61           In order to eliminate conflicts between the two subsystems,
  62           this config option enables the IDE driver's SATA support.
  63           Normally this is disabled, as it is preferred that libata
  64           supports SATA controllers, and this (IDE) driver supports
  65           PATA controllers.
  66
  67           If unsure, say N.
  68
  69 config IDE_GD
  70         tristate "generic ATA/ATAPI disk support"
  71         default y
  72         help
  73           Support for ATA/ATAPI disks (including ATAPI floppy drives).
  74
  75           To compile this driver as a module, choose M here.
  76           The module will be called ide-gd_mod.
  77
  78           If unsure, say Y.
  79
  80 config IDE_GD_ATA
  81         bool "ATA disk support"
  82         depends on IDE_GD
  83         default y
  84         help
  85           This will include support for ATA hard disks.
  86
  87           If unsure, say Y.
  88
  89 config IDE_GD_ATAPI
  90         bool "ATAPI floppy support"
  91         depends on IDE_GD
  92         select IDE_ATAPI
  93         help
  94           This will include support for ATAPI floppy drives
  95           (i.e. Iomega ZIP or MKE LS-120).
  96
  97           For information about jumper settings and the question
  98           of when a ZIP drive uses a partition table, see
  99           <http://www.win.tue.nl/~aeb/linux/zip/zip-1.html>.
 100
 101           If unsure, say N.
 102
 103 config BLK_DEV_IDECS
 104         tristate "PCMCIA IDE support"
 105         depends on PCMCIA
 106         help
 107           Support for Compact Flash cards, outboard IDE disks, tape drives,
 108           and CD-ROM drives connected through a PCMCIA card.
 109
 110 config BLK_DEV_DELKIN
 111         tristate "Cardbus IDE support (Delkin/ASKA/Workbit)"
 112         depends on CARDBUS && PCI
 113         help
 114           Support for Delkin, ASKA, and Workbit Cardbus CompactFlash
 115           Adapters.  This may also work for similar SD and XD adapters.
 116
 117 config BLK_DEV_IDECD
 118         tristate "Include IDE/ATAPI CDROM support"
 119         select IDE_ATAPI
 120         ---help---
 121           If you have a CD-ROM drive using the ATAPI protocol, say Y. ATAPI is
 122           a newer protocol used by IDE CD-ROM and TAPE drives, similar to the
 123           SCSI protocol. Most new CD-ROM drives use ATAPI, including the
 124           NEC-260, Mitsumi FX400, Sony 55E, and just about all non-SCSI
 125           double(2X) or better speed drives.
 126
 127           If you say Y here, the CD-ROM drive will be identified at boot time
 128           along with other IDE devices, as "hdb" or "hdc", or something
 129           similar (check the boot messages with dmesg). If this is your only
 130           CD-ROM drive, you can say N to all other CD-ROM options, but be sure
 131           to say Y or M to "ISO 9660 CD-ROM file system support".
 132
 133           To compile this driver as a module, choose M here: the
 134           module will be called ide-cd.
 135
 136 config BLK_DEV_IDECD_VERBOSE_ERRORS
 137         bool "Verbose error logging for IDE/ATAPI CDROM driver" if EXPERT
 138         depends on BLK_DEV_IDECD
 139         default y
 140         help
 141           Turn this on to have the driver print out the meanings of the
 142           ATAPI error codes.  This will use up additional 8kB of kernel-space
 143           memory, though.
 144
 145 config BLK_DEV_IDETAPE
 146         tristate "Include IDE/ATAPI TAPE support"
 147         select IDE_ATAPI
 148         help
 149           If you have an IDE tape drive using the ATAPI protocol, say Y.
 150           ATAPI is a newer protocol used by IDE tape and CD-ROM drives,
 151           similar to the SCSI protocol.  If you have an SCSI tape drive
 152           however, you can say N here.
 153
 154           You should also say Y if you have an OnStream DI-30 tape drive; this
 155           will not work with the SCSI protocol, until there is support for the
 156           SC-30 and SC-50 versions.
 157
 158           If you say Y here, the tape drive will be identified at boot time
 159           along with other IDE devices, as "hdb" or "hdc", or something
 160           similar, and will be mapped to a character device such as "ht0"
 161           (check the boot messages with dmesg).  Be sure to consult the
 162           <file:drivers/ide/ide-tape.c> and <file:Documentation/ide/ide.txt>
 163           files for usage information.
 164
 165           To compile this driver as a module, choose M here: the
 166           module will be called ide-tape.
 167
 168 config BLK_DEV_IDEACPI
 169         bool "IDE ACPI support"
 170         depends on ACPI
 171         ---help---
 172           Implement ACPI support for generic IDE devices. On modern
 173           machines ACPI support is required to properly handle ACPI S3 states.
 174
 175 config IDE_TASK_IOCTL
 176         bool "IDE Taskfile Access"
 177         help
 178           This is a direct raw access to the media.  It is a complex but
 179           elegant solution to test and validate the domain of the hardware and
 180           perform below the driver data recovery if needed.  This is the most
 181           basic form of media-forensics.
 182
 183           If you are unsure, say N here.
 184
 185 config IDE_PROC_FS
 186         bool "legacy /proc/ide/ support"
 187         depends on IDE && PROC_FS
 188         default y
 189         help
 190           This option enables support for the various files in
 191           /proc/ide.  In Linux 2.6 this has been superseded by
 192           files in sysfs but many legacy applications rely on this.
 193
 194           If unsure say Y.
 195
 196 comment "IDE chipset support/bugfixes"
 197
 198 config IDE_GENERIC
 199         tristate "generic/default IDE chipset support"
 200         depends on ALPHA || X86 || IA64 || M32R || MIPS || ARCH_RPC
 201         default ARM && ARCH_RPC
 202         help
 203           This is the generic IDE driver.  This driver attaches to the
 204           fixed legacy ports (e.g. on PCs 0x1f0/0x170, 0x1e8/0x168 and
 205           so on).  Please note that if this driver is built into the
 206           kernel or loaded before other ATA (IDE or libata) drivers
 207           and the controller is located at legacy ports, this driver
 208           may grab those ports and thus can prevent the controller
 209           specific driver from attaching.
 210
 211           Also, currently, IDE generic doesn't allow IRQ sharing
 212           meaning that the IRQs it grabs won't be available to other
 213           controllers sharing those IRQs which usually makes drivers
 214           for those controllers fail.  Generally, it's not a good idea
 215           to load IDE generic driver on modern systems.
 216
 217           If unsure, say N.
 218
 219 config BLK_DEV_PLATFORM
 220         tristate "Platform driver for IDE interfaces"
 221         help
 222           This is the platform IDE driver, used mostly for Memory Mapped
 223           IDE devices, like Compact Flashes running in True IDE mode.
 224
 225           If unsure, say N.
 226
 227 config BLK_DEV_CMD640
 228         tristate "CMD640 chipset bugfix/support"
 229         depends on X86
 230         select IDE_TIMINGS
 231         ---help---
 232           The CMD-Technologies CMD640 IDE chip is used on many common 486 and
 233           Pentium motherboards, usually in combination with a "Neptune" or
 234           "SiS" chipset. Unfortunately, it has a number of rather nasty
 235           design flaws that can cause severe data corruption under many common
 236           conditions. Say Y here to include code which tries to automatically
 237           detect and correct the problems under Linux. This option also
 238           enables access to the secondary IDE ports in some CMD640 based
 239           systems.
 240
 241           This driver will work automatically in PCI based systems (most new
 242           systems have PCI slots). But if your system uses VESA local bus
 243           (VLB) instead of PCI, you must also supply a kernel boot parameter
 244           to enable the CMD640 bugfix/support: "cmd640.probe_vlb". (Try "man
 245           bootparam" or see the documentation of your boot loader about how to
 246           pass options to the kernel.)
 247
 248           The CMD640 chip is also used on add-in cards by Acculogic, and on
 249           the "CSA-6400E PCI to IDE controller" that some people have. For
 250           details, read <file:Documentation/ide/ide.txt>.
 251
 252 config BLK_DEV_CMD640_ENHANCED
 253         bool "CMD640 enhanced support"
 254         depends on BLK_DEV_CMD640
 255         help
 256           This option includes support for setting/autotuning PIO modes and
 257           prefetch on CMD640 IDE interfaces.  For details, read
 258           <file:Documentation/ide/ide.txt>. If you have a CMD640 IDE interface
 259           and your BIOS does not already do this for you, then say Y here.
 260           Otherwise say N.
 261
 262 config BLK_DEV_IDEPNP
 263         tristate "PNP EIDE support"
 264         depends on PNP
 265         help
 266           If you have a PnP (Plug and Play) compatible EIDE card and
 267           would like the kernel to automatically detect and activate
 268           it, say Y here.
 269
 270 config BLK_DEV_IDEDMA_SFF
 271         bool
 272
 273 if PCI
 274
 275 comment "PCI IDE chipsets support"
 276
 277 config BLK_DEV_IDEPCI
 278         bool
 279
 280 config IDEPCI_PCIBUS_ORDER
 281         bool "Probe IDE PCI devices in the PCI bus order (DEPRECATED)"
 282         depends on IDE=y && BLK_DEV_IDEPCI
 283         default y
 284         help
 285           Probe IDE PCI devices in the order in which they appear on the
 286           PCI bus (i.e. 00:1f.1 PCI device before 02:01.0 PCI device)
 287           instead of the order in which IDE PCI host drivers are loaded.
 288
 289           Please note that this method of assuring stable naming of
 290           IDE devices is unreliable and use other means for achieving
 291           it (i.e. udev).
 292
 293           If in doubt, say N.
 294
 295 # TODO: split it on per host driver config options (or module parameters)
 296 config BLK_DEV_OFFBOARD
 297         bool "Boot off-board chipsets first support (DEPRECATED)"
 298         depends on BLK_DEV_IDEPCI && (BLK_DEV_AEC62XX || BLK_DEV_GENERIC || BLK_DEV_HPT366 || BLK_DEV_PDC202XX_NEW || BLK_DEV_PDC202XX_OLD || BLK_DEV_TC86C001)
 299         help
 300           Normally, IDE controllers built into the motherboard (on-board
 301           controllers) are assigned to ide0 and ide1 while those on add-in PCI
 302           cards (off-board controllers) are relegated to ide2 and ide3.
 303           Answering Y here will allow you to reverse the situation, with
 304           off-board controllers on ide0/1 and on-board controllers on ide2/3.
 305           This can improve the usability of some boot managers such as lilo
 306           when booting from a drive on an off-board controller.
 307
 308           Note that, if you do this, the order of the hd* devices will be
 309           rearranged which may require modification of fstab and other files.
 310
 311           Please also note that this method of assuring stable naming of
 312           IDE devices is unreliable and use other means for achieving it
 313           (i.e. udev).
 314
 315           If in doubt, say N.
 316
 317 config BLK_DEV_GENERIC
 318         tristate "Generic PCI IDE Chipset Support"
 319         select BLK_DEV_IDEPCI
 320         help
 321           This option provides generic support for various PCI IDE Chipsets
 322           which otherwise might not be supported.
 323
 324 config BLK_DEV_OPTI621
 325         tristate "OPTi 82C621 chipset enhanced support"
 326         select BLK_DEV_IDEPCI
 327         help
 328           This is a driver for the OPTi 82C621 EIDE controller.
 329           Please read the comments at the top of <file:drivers/ide/opti621.c>.
 330
 331 config BLK_DEV_RZ1000
 332         tristate "RZ1000 chipset bugfix/support"
 333         depends on X86
 334         select BLK_DEV_IDEPCI
 335         help
 336           The PC-Technologies RZ1000 IDE chip is used on many common 486 and
 337           Pentium motherboards, usually along with the "Neptune" chipset.
 338           Unfortunately, it has a rather nasty design flaw that can cause
 339           severe data corruption under many conditions. Say Y here to include
 340           code which automatically detects and corrects the problem under
 341           Linux. This may slow disk throughput by a few percent, but at least
 342           things will operate 100% reliably.
 343
 344 config BLK_DEV_IDEDMA_PCI
 345         bool
 346         select BLK_DEV_IDEPCI
 347         select BLK_DEV_IDEDMA_SFF
 348
 349 config BLK_DEV_AEC62XX
 350         tristate "AEC62XX chipset support"
 351         select BLK_DEV_IDEDMA_PCI
 352         help
 353           This driver adds explicit support for Acard AEC62xx (Artop ATP8xx)
 354           IDE controllers. This allows the kernel to change PIO, DMA and UDMA
 355           speeds and to configure the chip to optimum performance.
 356
 357 config BLK_DEV_ALI15X3
 358         tristate "ALI M15x3 chipset support"
 359         select IDE_TIMINGS
 360         select BLK_DEV_IDEDMA_PCI
 361         help
 362           This driver ensures (U)DMA support for ALI 1533, 1543 and 1543C
 363           onboard chipsets.  It also tests for Simplex mode and enables
 364           normal dual channel support.
 365
 366           Please read the comments at the top of
 367           <file:drivers/ide/alim15x3.c>.
 368
 369           If unsure, say N.
 370
 371 config BLK_DEV_AMD74XX
 372         tristate "AMD and nVidia IDE support"
 373         depends on !ARM
 374         select IDE_TIMINGS
 375         select BLK_DEV_IDEDMA_PCI
 376         help
 377           This driver adds explicit support for AMD-7xx and AMD-8111 chips
 378           and also for the nVidia nForce chip.  This allows the kernel to
 379           change PIO, DMA and UDMA speeds and to configure the chip to
 380           optimum performance.
 381
 382 config BLK_DEV_ATIIXP
 383         tristate "ATI IXP chipset IDE support"
 384         depends on X86
 385         select BLK_DEV_IDEDMA_PCI
 386         help
 387           This driver adds explicit support for ATI IXP chipset.
 388           This allows the kernel to change PIO, DMA and UDMA speeds
 389           and to configure the chip to optimum performance.
 390
 391           Say Y here if you have an ATI IXP chipset IDE controller.
 392
 393 config BLK_DEV_CMD64X
 394         tristate "CMD64{3|6|8|9} chipset support"
 395         select IDE_TIMINGS
 396         select BLK_DEV_IDEDMA_PCI
 397         help
 398           Say Y here if you have an IDE controller which uses any of these
 399           chipsets: CMD643, CMD646, or CMD648.
 400
 401 config BLK_DEV_TRIFLEX
 402         tristate "Compaq Triflex IDE support"
 403         select BLK_DEV_IDEDMA_PCI
 404         help
 405           Say Y here if you have a Compaq Triflex IDE controller, such
 406           as those commonly found on Compaq Pentium-Pro systems
 407
 408 config BLK_DEV_CY82C693
 409         tristate "CY82C693 chipset support"
 410         depends on ALPHA
 411         select IDE_TIMINGS
 412         select BLK_DEV_IDEDMA_PCI
 413         help
 414           This driver adds detection and support for the CY82C693 chipset
 415           used on Digital's PC-Alpha 164SX boards.
 416
 417 config BLK_DEV_CS5520
 418         tristate "Cyrix CS5510/20 MediaGX chipset support (VERY EXPERIMENTAL)"
 419         depends on X86_32 || COMPILE_TEST
 420         select BLK_DEV_IDEDMA_PCI
 421         help
 422           Include support for PIO tuning and virtual DMA on the Cyrix MediaGX
 423           5510/5520 chipset. This will automatically be detected and
 424           configured if found.
 425
 426           It is safe to say Y to this question.
 427
 428 config BLK_DEV_CS5530
 429         tristate "Cyrix/National Semiconductor CS5530 MediaGX chipset support"
 430         depends on X86_32 || COMPILE_TEST
 431         select BLK_DEV_IDEDMA_PCI
 432         help
 433           Include support for UDMA on the Cyrix MediaGX 5530 chipset. This
 434           will automatically be detected and configured if found.
 435
 436           It is safe to say Y to this question.
 437
 438 config BLK_DEV_CS5535
 439         tristate "AMD CS5535 chipset support"
 440         depends on X86_32
 441         select BLK_DEV_IDEDMA_PCI
 442         help
 443           Include support for UDMA on the NSC/AMD CS5535 companion chipset.
 444           This will automatically be detected and configured if found.
 445
 446           It is safe to say Y to this question.
 447
 448 config BLK_DEV_CS5536
 449         tristate "CS5536 chipset support"
 450         depends on X86_32
 451         select BLK_DEV_IDEDMA_PCI
 452         help
 453           This option enables support for the AMD CS5536
 454           companion chip used with the Geode LX processor family.
 455
 456           If unsure, say N.
 457
 458 config BLK_DEV_HPT366
 459         tristate "HPT36X/37X chipset support"
 460         select BLK_DEV_IDEDMA_PCI
 461         help
 462           HPT366 is an Ultra DMA chipset for ATA-66.
 463           HPT368 is an Ultra DMA chipset for ATA-66 RAID Based.
 464           HPT370 is an Ultra DMA chipset for ATA-100.
 465           HPT372 is an Ultra DMA chipset for ATA-100.
 466           HPT374 is an Ultra DMA chipset for ATA-100.
 467
 468           This driver adds up to 4 more EIDE devices sharing a single
 469           interrupt.
 470
 471           The HPT366 chipset in its current form is bootable. One solution
 472           for this problem are special LILO commands for redirecting the
 473           reference to device 0x80. The other solution is to say Y to "Boot
 474           off-board chipsets first support" (CONFIG_BLK_DEV_OFFBOARD) unless
 475           your mother board has the chipset natively mounted. Regardless one
 476           should use the fore mentioned option and call at LILO.
 477
 478           This driver requires dynamic tuning of the chipset during the
 479           ide-probe at boot. It is reported to support DVD II drives, by the
 480           manufacturer.
 481
 482 config BLK_DEV_JMICRON
 483         tristate "JMicron JMB36x support"
 484         select BLK_DEV_IDEDMA_PCI
 485         help
 486           Basic support for the JMicron ATA controllers. For full support
 487           use the libata drivers.
 488
 489 config BLK_DEV_SC1200
 490         tristate "National SCx200 chipset support"
 491         depends on X86_32 || COMPILE_TEST
 492         select BLK_DEV_IDEDMA_PCI
 493         help
 494           This driver adds support for the on-board IDE controller on the
 495           National SCx200 series of embedded x86 "Geode" systems.
 496
 497 config BLK_DEV_PIIX
 498         tristate "Intel PIIX/ICH chipsets support"
 499         select BLK_DEV_IDEDMA_PCI
 500         help
 501           This driver adds explicit support for Intel PIIX and ICH chips.
 502           This allows the kernel to change PIO, DMA and UDMA speeds and to
 503           configure the chip to optimum performance.
 504
 505 config BLK_DEV_IT8172
 506         tristate "IT8172 IDE support"
 507         select BLK_DEV_IDEDMA_PCI
 508         help
 509           This driver adds support for the IDE controller on the
 510           IT8172 System Controller.
 511
 512 config BLK_DEV_IT8213
 513         tristate "IT8213 IDE support"
 514         select BLK_DEV_IDEDMA_PCI
 515         help
 516          This driver adds support for the ITE 8213 IDE controller.
 517
 518 config BLK_DEV_IT821X
 519         tristate "IT821X IDE support"
 520         select BLK_DEV_IDEDMA_PCI
 521         help
 522           This driver adds support for the ITE 8211 IDE controller and the
 523           IT 8212 IDE RAID controller in both RAID and pass-through mode.
 524
 525 config BLK_DEV_NS87415
 526         tristate "NS87415 chipset support"
 527         select BLK_DEV_IDEDMA_PCI
 528         help
 529           This driver adds detection and support for the NS87415 chip
 530           (used mainly on SPARC64 and PA-RISC machines).
 531
 532           Please read the comments at the top of <file:drivers/ide/ns87415.c>.
 533
 534 config BLK_DEV_PDC202XX_OLD
 535         tristate "PROMISE PDC202{46|62|65|67} support"
 536         select BLK_DEV_IDEDMA_PCI
 537         help
 538           Promise Ultra33 or PDC20246
 539           Promise Ultra66 or PDC20262
 540           Promise Ultra100 or PDC20265/PDC20267/PDC20268
 541
 542           This driver adds up to 4 more EIDE devices sharing a single
 543           interrupt. This add-on card is a bootable PCI UDMA controller. Since
 544           multiple cards can be installed and there are BIOS ROM problems that
 545           happen if the BIOS revisions of all installed cards (three-max) do
 546           not match, the driver attempts to do dynamic tuning of the chipset
 547           at boot-time for max-speed.  Ultra33 BIOS 1.25 or newer is required
 548           for more than one card.
 549
 550           Please read the comments at the top of
 551           <file:drivers/ide/pdc202xx_old.c>.
 552
 553           If unsure, say N.
 554
 555 config BLK_DEV_PDC202XX_NEW
 556         tristate "PROMISE PDC202{68|69|70|71|75|76|77} support"
 557         select BLK_DEV_IDEDMA_PCI
 558
 559 config BLK_DEV_SVWKS
 560         tristate "ServerWorks OSB4/CSB5/CSB6 chipsets support"
 561         select BLK_DEV_IDEDMA_PCI
 562         help
 563           This driver adds PIO/(U)DMA support for the ServerWorks OSB4/CSB5
 564           chipsets.
 565
 566 config BLK_DEV_SGIIOC4
 567         tristate "Silicon Graphics IOC4 chipset ATA/ATAPI support"
 568         depends on (IA64_SGI_SN2 || IA64_GENERIC) && SGI_IOC4
 569         select BLK_DEV_IDEDMA_PCI
 570         help
 571           This driver adds PIO & MultiMode DMA-2 support for the SGI IOC4
 572           chipset, which has one channel and can support two devices.
 573           Please say Y here if you have an Altix System from SGI.
 574
 575 config BLK_DEV_SIIMAGE
 576         tristate "Silicon Image chipset support"
 577         select BLK_DEV_IDEDMA_PCI
 578         help
 579           This driver adds PIO/(U)DMA support for the SI CMD680 and SII
 580           3112 (Serial ATA) chips.
 581
 582 config BLK_DEV_SIS5513
 583         tristate "SiS5513 chipset support"
 584         depends on X86
 585         select BLK_DEV_IDEDMA_PCI
 586         help
 587           This driver ensures (U)DMA support for SIS5513 chipset family based
 588           mainboards.
 589
 590           The following chipsets are supported:
 591           ATA16:  SiS5511, SiS5513
 592           ATA33:  SiS5591, SiS5597, SiS5598, SiS5600
 593           ATA66:  SiS530, SiS540, SiS620, SiS630, SiS640
 594           ATA100: SiS635, SiS645, SiS650, SiS730, SiS735, SiS740,
 595           SiS745, SiS750
 596
 597           Please read the comments at the top of <file:drivers/ide/sis5513.c>.
 598
 599 config BLK_DEV_SL82C105
 600         tristate "Winbond SL82c105 support"
 601         depends on (PPC || ARM)
 602         select IDE_TIMINGS
 603         select BLK_DEV_IDEDMA_PCI
 604         help
 605           If you have a Winbond SL82c105 IDE controller, say Y here to enable
 606           special configuration for this chip. This is common on various CHRP
 607           motherboards, but could be used elsewhere. If in doubt, say Y.
 608
 609 config BLK_DEV_SLC90E66
 610         tristate "SLC90E66 chipset support"
 611         select BLK_DEV_IDEDMA_PCI
 612         help
 613           This driver ensures (U)DMA support for Victory66 SouthBridges for
 614           SMsC with Intel NorthBridges.  This is an Ultra66 based chipset.
 615           The nice thing about it is that you can mix Ultra/DMA/PIO devices
 616           and it will handle timing cycles.  Since this is an improved
 617           look-a-like to the PIIX4 it should be a nice addition.
 618
 619           Please read the comments at the top of
 620           <file:drivers/ide/slc90e66.c>.
 621
 622 config BLK_DEV_TRM290
 623         tristate "Tekram TRM290 chipset support"
 624         select BLK_DEV_IDEDMA_PCI
 625         help
 626           This driver adds support for bus master DMA transfers
 627           using the Tekram TRM290 PCI IDE chip. Volunteers are
 628           needed for further tweaking and development.
 629           Please read the comments at the top of <file:drivers/ide/trm290.c>.
 630
 631 config BLK_DEV_VIA82CXXX
 632         tristate "VIA82CXXX chipset support"
 633         select IDE_TIMINGS
 634         select BLK_DEV_IDEDMA_PCI
 635         help
 636           This driver adds explicit support for VIA BusMastering IDE chips.
 637           This allows the kernel to change PIO, DMA and UDMA speeds and to
 638           configure the chip to optimum performance.
 639
 640 config BLK_DEV_TC86C001
 641         tristate "Toshiba TC86C001 support"
 642         select BLK_DEV_IDEDMA_PCI
 643         help
 644         This driver adds support for Toshiba TC86C001 GOKU-S chip.
 645
 646 config BLK_DEV_CELLEB
 647         tristate "Toshiba's Cell Reference Set IDE support"
 648         depends on PPC_CELLEB
 649         select BLK_DEV_IDEDMA_PCI
 650         help
 651           This driver provides support for the on-board IDE controller on
 652           Toshiba Cell Reference Board.
 653           If unsure, say Y.
 654
 655 endif
 656
 657 # TODO: BLK_DEV_IDEDMA_PCI -> BLK_DEV_IDEDMA_SFF
 658 config BLK_DEV_IDE_PMAC
 659         tristate "PowerMac on-board IDE support"
 660         depends on PPC_PMAC
 661         select IDE_TIMINGS
 662         select BLK_DEV_IDEDMA_PCI
 663         help
 664           This driver provides support for the on-board IDE controller on
 665           most of the recent Apple Power Macintoshes and PowerBooks.
 666           If unsure, say Y.
 667
 668 config BLK_DEV_IDE_PMAC_ATA100FIRST
 669         bool "Probe on-board ATA/100 (Kauai) first"
 670         depends on BLK_DEV_IDE_PMAC
 671         help
 672           This option will cause the ATA/100 controller found in UniNorth2
 673           based machines (Windtunnel PowerMac, Aluminium PowerBooks, ...)
 674           to be probed before the ATA/66 and ATA/33 controllers. Without
 675           these, those machine used to have the hard disk on hdc and the
 676           CD-ROM on hda. This option changes this to more natural hda for
 677           hard disk and hdc for CD-ROM.
 678
 679 config BLK_DEV_IDE_AU1XXX
 680        bool "IDE for AMD Alchemy Au1200"
 681        depends on MIPS_ALCHEMY
 682        select IDE_XFER_MODE
 683 choice
 684        prompt "IDE Mode for AMD Alchemy Au1200"
 685        default BLK_DEV_IDE_AU1XXX_PIO_DBDMA
 686        depends on BLK_DEV_IDE_AU1XXX
 687
 688 config BLK_DEV_IDE_AU1XXX_PIO_DBDMA
 689        bool "PIO+DbDMA IDE for AMD Alchemy Au1200"
 690
 691 config BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
 692        bool "MDMA2+DbDMA IDE for AMD Alchemy Au1200"
 693        depends on BLK_DEV_IDE_AU1XXX
 694 endchoice
 695
 696 config BLK_DEV_IDE_TX4938
 697         tristate "TX4938 internal IDE support"
 698         depends on SOC_TX4938
 699         select IDE_TIMINGS
 700
 701 config BLK_DEV_IDE_TX4939
 702         tristate "TX4939 internal IDE support"
 703         depends on SOC_TX4939
 704         select BLK_DEV_IDEDMA_SFF
 705
 706 config BLK_DEV_IDE_ICSIDE
 707         tristate "ICS IDE interface support"
 708         depends on ARM && ARCH_ACORN
 709         help
 710           On Acorn systems, say Y here if you wish to use the ICS IDE
 711           interface card.  This is not required for ICS partition support.
 712           If you are unsure, say N to this.
 713
 714 config BLK_DEV_IDEDMA_ICS
 715         bool "ICS DMA support"
 716         depends on BLK_DEV_IDE_ICSIDE
 717         help
 718           Say Y here if you want to add DMA (Direct Memory Access) support to
 719           the ICS IDE driver.
 720
 721 config BLK_DEV_IDE_RAPIDE
 722         tristate "RapIDE interface support"
 723         depends on ARM && ARCH_ACORN
 724         help
 725           Say Y here if you want to support the Yellowstone RapIDE controller
 726           manufactured for use with Acorn computers.
 727
 728 config BLK_DEV_GAYLE
 729         tristate "Amiga Gayle IDE interface support"
 730         depends on AMIGA
 731         help
 732           This is the IDE driver for the Amiga Gayle IDE interface. It supports
 733           both the `A1200 style' and `A4000 style' of the Gayle IDE interface,
 734           This includes on-board IDE interfaces on some Amiga models (A600,
 735           A1200, A4000, and A4000T), and IDE interfaces on the Zorro expansion
 736           bus (M-Tech E-Matrix 530 expansion card).
 737
 738           It also provides support for the so-called `IDE doublers' (made
 739           by various manufacturers, e.g. Eyetech) that can be connected to
 740           the on-board IDE interface of some Amiga models. Using such an IDE
 741           doubler, you can connect up to four instead of two IDE devices to
 742           the Amiga's on-board IDE interface. The feature is enabled at kernel
 743           runtime using the "gayle.doubler" kernel boot parameter.
 744
 745           Say Y if you have an Amiga with a Gayle IDE interface and want to use
 746           IDE devices (hard disks, CD-ROM drives, etc.) that are connected to
 747           it.
 748
 749           Note that you also have to enable Zorro bus support if you want to
 750           use Gayle IDE interfaces on the Zorro expansion bus.
 751
 752 config BLK_DEV_BUDDHA
 753         tristate "Buddha/Catweasel/X-Surf IDE interface support"
 754         depends on ZORRO
 755         help
 756           This is the IDE driver for the IDE interfaces on the Buddha, Catweasel
 757           and X-Surf expansion boards.  It supports up to two interfaces on the
 758           Buddha, three on the Catweasel and two on the X-Surf.
 759
 760           Say Y if you have a Buddha or Catweasel expansion board and want to
 761           use IDE devices (hard disks, CD-ROM drives, etc.) that are connected
 762           to one of its IDE interfaces.
 763
 764 config BLK_DEV_FALCON_IDE
 765         tristate "Falcon IDE interface support"
 766         depends on ATARI
 767         help
 768           This is the IDE driver for the on-board IDE interface on the Atari
 769           Falcon. Say Y if you have a Falcon and want to use IDE devices (hard
 770           disks, CD-ROM drives, etc.) that are connected to the on-board IDE
 771           interface.
 772
 773 config BLK_DEV_MAC_IDE
 774         tristate "Macintosh Quadra/Powerbook IDE interface support"
 775         depends on MAC
 776         help
 777           This is the IDE driver for the on-board IDE interface on some m68k
 778           Macintosh models. It supports both the `Quadra style' (used in
 779           Quadra/ Centris 630 and Performa 588 models) and `Powerbook style'
 780           (used in the Powerbook 150 and 190 models) IDE interface.
 781
 782           Say Y if you have such an Macintosh model and want to use IDE
 783           devices (hard disks, CD-ROM drives, etc.) that are connected to the
 784           on-board IDE interface.
 785
 786 config BLK_DEV_Q40IDE
 787         tristate "Q40/Q60 IDE interface support"
 788         depends on Q40
 789         help
 790           Enable the on-board IDE controller in the Q40/Q60.  This should
 791           normally be on; disable it only if you are running a custom hard
 792           drive subsystem through an expansion card.
 793
 794 config BLK_DEV_PALMCHIP_BK3710
 795         tristate "Palmchip bk3710 IDE controller support"
 796         depends on ARCH_DAVINCI
 797         select IDE_TIMINGS
 798         select BLK_DEV_IDEDMA_SFF
 799         help
 800           Say Y here if you want to support the onchip IDE controller on the
 801           TI DaVinci SoC
 802
 803 # no isa -> no vlb
 804 if ISA && (ALPHA || X86 || MIPS)
 805
 806 comment "Other IDE chipsets support"
 807 comment "Note: most of these also require special kernel boot parameters"
 808
 809 config BLK_DEV_4DRIVES
 810         tristate "Generic 4 drives/port support"
 811         help
 812           Certain older chipsets, including the Tekram 690CD, use a single set
 813           of I/O ports at 0x1f0 to control up to four drives, instead of the
 814           customary two drives per port. Support for this can be enabled at
 815           runtime using the "ide-4drives.probe" kernel boot parameter if you
 816           say Y here.
 817
 818 config BLK_DEV_ALI14XX
 819         tristate "ALI M14xx support"
 820         select IDE_TIMINGS
 821         select IDE_LEGACY
 822         help
 823           This driver is enabled at runtime using the "ali14xx.probe" kernel
 824           boot parameter.  It enables support for the secondary IDE interface
 825           of the ALI M1439/1443/1445/1487/1489 chipsets, and permits faster
 826           I/O speeds to be set as well.
 827           See the files <file:Documentation/ide/ide.txt> and
 828           <file:drivers/ide/ali14xx.c> for more info.
 829
 830 config BLK_DEV_DTC2278
 831         tristate "DTC-2278 support"
 832         select IDE_XFER_MODE
 833         select IDE_LEGACY
 834         help
 835           This driver is enabled at runtime using the "dtc2278.probe" kernel
 836           boot parameter. It enables support for the secondary IDE interface
 837           of the DTC-2278 card, and permits faster I/O speeds to be set as
 838           well. See the <file:Documentation/ide/ide.txt> and
 839           <file:drivers/ide/dtc2278.c> files for more info.
 840
 841 config BLK_DEV_HT6560B
 842         tristate "Holtek HT6560B support"
 843         select IDE_TIMINGS
 844         select IDE_LEGACY
 845         help
 846           This driver is enabled at runtime using the "ht6560b.probe" kernel
 847           boot parameter. It enables support for the secondary IDE interface
 848           of the Holtek card, and permits faster I/O speeds to be set as well.
 849           See the <file:Documentation/ide/ide.txt> and
 850           <file:drivers/ide/ht6560b.c> files for more info.
 851
 852 config BLK_DEV_QD65XX
 853         tristate "QDI QD65xx support"
 854         select IDE_TIMINGS
 855         select IDE_LEGACY
 856         help
 857           This driver is enabled at runtime using the "qd65xx.probe" kernel
 858           boot parameter.  It permits faster I/O speeds to be set.  See the
 859           <file:Documentation/ide/ide.txt> and <file:drivers/ide/qd65xx.c>
 860           for more info.
 861
 862 config BLK_DEV_UMC8672
 863         tristate "UMC-8672 support"
 864         select IDE_XFER_MODE
 865         select IDE_LEGACY
 866         help
 867           This driver is enabled at runtime using the "umc8672.probe" kernel
 868           boot parameter. It enables support for the secondary IDE interface
 869           of the UMC-8672, and permits faster I/O speeds to be set as well.
 870           See the files <file:Documentation/ide/ide.txt> and
 871           <file:drivers/ide/umc8672.c> for more info.
 872
 873 endif
 874
 875 config BLK_DEV_IDEDMA
 876         def_bool BLK_DEV_IDEDMA_SFF || \
 877                  BLK_DEV_IDEDMA_ICS || BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
 878         select IDE_XFER_MODE
 879
 880 endif # IDE