ide: remove dead/obsolete ->busproc method

[mirror_ubuntu-zesty-kernel.git] / drivers / ide / pci / sgiioc4.c

/*
 * Copyright (c) 2003-2006 Silicon Graphics, Inc.  All Rights Reserved.
 *
 * This program is free software; you can redistribute it and/or modify it
 * under the terms of version 2 of the GNU General Public License
 * as published by the Free Software Foundation.
 *
 * This program is distributed in the hope that it would be useful, but
 * WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
 *
 * You should have received a copy of the GNU General Public
 * License along with this program; if not, write the Free Software
 * Foundation, Inc., 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
 *
 * For further information regarding this notice, see:
 *
 * http://oss.sgi.com/projects/GenInfo/NoticeExplan
 */

#include <linux/module.h>
#include <linux/types.h>
#include <linux/pci.h>
#include <linux/delay.h>
#include <linux/hdreg.h>
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/ioport.h>
#include <linux/blkdev.h>
#include <linux/scatterlist.h>
#include <linux/ioc4.h>
#include <asm/io.h>

#include <linux/ide.h>

#define DRV_NAME "SGIIOC4"

/* IOC4 Specific Definitions */
#define IOC4_CMD_OFFSET         0x100
#define IOC4_CTRL_OFFSET        0x120
#define IOC4_DMA_OFFSET         0x140
#define IOC4_INTR_OFFSET        0x0

#define IOC4_TIMING             0x00
#define IOC4_DMA_PTR_L          0x01
#define IOC4_DMA_PTR_H          0x02
#define IOC4_DMA_ADDR_L         0x03
#define IOC4_DMA_ADDR_H         0x04
#define IOC4_BC_DEV             0x05
#define IOC4_BC_MEM             0x06
#define IOC4_DMA_CTRL           0x07
#define IOC4_DMA_END_ADDR       0x08

/* Bits in the IOC4 Control/Status Register */
#define IOC4_S_DMA_START        0x01
#define IOC4_S_DMA_STOP         0x02
#define IOC4_S_DMA_DIR          0x04
#define IOC4_S_DMA_ACTIVE       0x08
#define IOC4_S_DMA_ERROR        0x10
#define IOC4_ATA_MEMERR         0x02

/* Read/Write Directions */
#define IOC4_DMA_WRITE          0x04
#define IOC4_DMA_READ           0x00

/* Interrupt Register Offsets */
#define IOC4_INTR_REG           0x03
#define IOC4_INTR_SET           0x05
#define IOC4_INTR_CLEAR         0x07

#define IOC4_IDE_CACHELINE_SIZE 128
#define IOC4_CMD_CTL_BLK_SIZE   0x20
#define IOC4_SUPPORTED_FIRMWARE_REV 46

typedef struct {
        u32 timing_reg0;
        u32 timing_reg1;
        u32 low_mem_ptr;
        u32 high_mem_ptr;
        u32 low_mem_addr;
        u32 high_mem_addr;
        u32 dev_byte_count;
        u32 mem_byte_count;
        u32 status;
} ioc4_dma_regs_t;

/* Each Physical Region Descriptor Entry size is 16 bytes (2 * 64 bits) */
/* IOC4 has only 1 IDE channel */
#define IOC4_PRD_BYTES       16
#define IOC4_PRD_ENTRIES     (PAGE_SIZE /(4*IOC4_PRD_BYTES))


static void
sgiioc4_init_hwif_ports(hw_regs_t * hw, unsigned long data_port,
                        unsigned long ctrl_port, unsigned long irq_port)
{
        unsigned long reg = data_port;
        int i;

        /* Registers are word (32 bit) aligned */
        for (i = IDE_DATA_OFFSET; i <= IDE_STATUS_OFFSET; i++)
                hw->io_ports[i] = reg + i * 4;

        if (ctrl_port)
                hw->io_ports[IDE_CONTROL_OFFSET] = ctrl_port;

        if (irq_port)
                hw->io_ports[IDE_IRQ_OFFSET] = irq_port;
}

static void
sgiioc4_maskproc(ide_drive_t * drive, int mask)
{
        writeb(mask ? (drive->ctl | 2) : (drive->ctl & ~2),
               (void __iomem *)IDE_CONTROL_REG);
}


static int
sgiioc4_checkirq(ide_hwif_t * hwif)
{
        unsigned long intr_addr =
                hwif->io_ports[IDE_IRQ_OFFSET] + IOC4_INTR_REG * 4;

        if ((u8)readl((void __iomem *)intr_addr) & 0x03)
                return 1;

        return 0;
}

static u8 sgiioc4_INB(unsigned long);

static int
sgiioc4_clearirq(ide_drive_t * drive)
{
        u32 intr_reg;
        ide_hwif_t *hwif = HWIF(drive);
        unsigned long other_ir =
            hwif->io_ports[IDE_IRQ_OFFSET] + (IOC4_INTR_REG << 2);

        /* Code to check for PCI error conditions */
        intr_reg = readl((void __iomem *)other_ir);
        if (intr_reg & 0x03) { /* Valid IOC4-IDE interrupt */
                /*
                 * Using sgiioc4_INB to read the IDE_STATUS_REG has a side effect
                 * of clearing the interrupt.  The first read should clear it
                 * if it is set.  The second read should return a "clear" status
                 * if it got cleared.  If not, then spin for a bit trying to
                 * clear it.
                 */
                u8 stat = sgiioc4_INB(IDE_STATUS_REG);
                int count = 0;
                stat = sgiioc4_INB(IDE_STATUS_REG);
                while ((stat & 0x80) && (count++ < 100)) {
                        udelay(1);
                        stat = sgiioc4_INB(IDE_STATUS_REG);
                }

                if (intr_reg & 0x02) {
                        struct pci_dev *dev = to_pci_dev(hwif->dev);
                        /* Error when transferring DMA data on PCI bus */
                        u32 pci_err_addr_low, pci_err_addr_high,
                            pci_stat_cmd_reg;

                        pci_err_addr_low =
                                readl((void __iomem *)hwif->io_ports[IDE_IRQ_OFFSET]);
                        pci_err_addr_high =
                                readl((void __iomem *)(hwif->io_ports[IDE_IRQ_OFFSET] + 4));
                        pci_read_config_dword(dev, PCI_COMMAND,
                                              &pci_stat_cmd_reg);
                        printk(KERN_ERR
                               "%s(%s) : PCI Bus Error when doing DMA:"
                                   " status-cmd reg is 0x%x\n",
                               __FUNCTION__, drive->name, pci_stat_cmd_reg);
                        printk(KERN_ERR
                               "%s(%s) : PCI Error Address is 0x%x%x\n",
                               __FUNCTION__, drive->name,
                               pci_err_addr_high, pci_err_addr_low);
                        /* Clear the PCI Error indicator */
                        pci_write_config_dword(dev, PCI_COMMAND, 0x00000146);
                }

                /* Clear the Interrupt, Error bits on the IOC4 */
                writel(0x03, (void __iomem *)other_ir);

                intr_reg = readl((void __iomem *)other_ir);
        }

        return intr_reg & 3;
}

static void sgiioc4_ide_dma_start(ide_drive_t * drive)
{
        ide_hwif_t *hwif = HWIF(drive);
        unsigned long ioc4_dma_addr = hwif->dma_base + IOC4_DMA_CTRL * 4;
        unsigned int reg = readl((void __iomem *)ioc4_dma_addr);
        unsigned int temp_reg = reg | IOC4_S_DMA_START;

        writel(temp_reg, (void __iomem *)ioc4_dma_addr);
}

static u32
sgiioc4_ide_dma_stop(ide_hwif_t *hwif, u64 dma_base)
{
        unsigned long ioc4_dma_addr = dma_base + IOC4_DMA_CTRL * 4;
        u32     ioc4_dma;
        int     count;

        count = 0;
        ioc4_dma = readl((void __iomem *)ioc4_dma_addr);
        while ((ioc4_dma & IOC4_S_DMA_STOP) && (count++ < 200)) {
                udelay(1);
                ioc4_dma = readl((void __iomem *)ioc4_dma_addr);
        }
        return ioc4_dma;
}

/* Stops the IOC4 DMA Engine */
static int
sgiioc4_ide_dma_end(ide_drive_t * drive)
{
        u32 ioc4_dma, bc_dev, bc_mem, num, valid = 0, cnt = 0;
        ide_hwif_t *hwif = HWIF(drive);
        unsigned long dma_base = hwif->dma_base;
        int dma_stat = 0;
        unsigned long *ending_dma = ide_get_hwifdata(hwif);

        writel(IOC4_S_DMA_STOP, (void __iomem *)(dma_base + IOC4_DMA_CTRL * 4));

        ioc4_dma = sgiioc4_ide_dma_stop(hwif, dma_base);

        if (ioc4_dma & IOC4_S_DMA_STOP) {
                printk(KERN_ERR
                       "%s(%s): IOC4 DMA STOP bit is still 1 :"
                       "ioc4_dma_reg 0x%x\n",
                       __FUNCTION__, drive->name, ioc4_dma);
                dma_stat = 1;
        }

        /*
         * The IOC4 will DMA 1's to the ending dma area to indicate that
         * previous data DMA is complete.  This is necessary because of relaxed
         * ordering between register reads and DMA writes on the Altix.
         */
        while ((cnt++ < 200) && (!valid)) {
                for (num = 0; num < 16; num++) {
                        if (ending_dma[num]) {
                                valid = 1;
                                break;
                        }
                }
                udelay(1);
        }
        if (!valid) {
                printk(KERN_ERR "%s(%s) : DMA incomplete\n", __FUNCTION__,
                       drive->name);
                dma_stat = 1;
        }

        bc_dev = readl((void __iomem *)(dma_base + IOC4_BC_DEV * 4));
        bc_mem = readl((void __iomem *)(dma_base + IOC4_BC_MEM * 4));

        if ((bc_dev & 0x01FF) || (bc_mem & 0x1FF)) {
                if (bc_dev > bc_mem + 8) {
                        printk(KERN_ERR
                               "%s(%s): WARNING!! byte_count_dev %d "
                               "!= byte_count_mem %d\n",
                               __FUNCTION__, drive->name, bc_dev, bc_mem);
                }
        }

        drive->waiting_for_dma = 0;
        ide_destroy_dmatable(drive);

        return dma_stat;
}

static void sgiioc4_set_dma_mode(ide_drive_t *drive, const u8 speed)
{
}

/* returns 1 if dma irq issued, 0 otherwise */
static int
sgiioc4_ide_dma_test_irq(ide_drive_t * drive)
{
        return sgiioc4_checkirq(HWIF(drive));
}

static void sgiioc4_dma_host_set(ide_drive_t *drive, int on)
{
        if (!on)
                sgiioc4_clearirq(drive);
}

static void
sgiioc4_resetproc(ide_drive_t * drive)
{
        sgiioc4_ide_dma_end(drive);
        sgiioc4_clearirq(drive);
}

static void
sgiioc4_dma_lost_irq(ide_drive_t * drive)
{
        sgiioc4_resetproc(drive);

        ide_dma_lost_irq(drive);
}

static u8
sgiioc4_INB(unsigned long port)
{
        u8 reg = (u8) readb((void __iomem *) port);

        if ((port & 0xFFF) == 0x11C) {  /* Status register of IOC4 */
                if (reg & 0x51) {       /* Not busy...check for interrupt */
                        unsigned long other_ir = port - 0x110;
                        unsigned int intr_reg = (u32) readl((void __iomem *) other_ir);

                        /* Clear the Interrupt, Error bits on the IOC4 */
                        if (intr_reg & 0x03) {
                                writel(0x03, (void __iomem *) other_ir);
                                intr_reg = (u32) readl((void __iomem *) other_ir);
                        }
                }
        }

        return reg;
}

/* Creates a dma map for the scatter-gather list entries */
static int __devinit
ide_dma_sgiioc4(ide_hwif_t * hwif, unsigned long dma_base)
{
        struct pci_dev *dev = to_pci_dev(hwif->dev);
        void __iomem *virt_dma_base;
        int num_ports = sizeof (ioc4_dma_regs_t);
        void *pad;

        printk(KERN_INFO "%s: BM-DMA at 0x%04lx-0x%04lx\n", hwif->name,
               dma_base, dma_base + num_ports - 1);

        if (!request_mem_region(dma_base, num_ports, hwif->name)) {
                printk(KERN_ERR
                       "%s(%s) -- ERROR, Addresses 0x%p to 0x%p "
                       "ALREADY in use\n",
                       __FUNCTION__, hwif->name, (void *) dma_base,
                       (void *) dma_base + num_ports - 1);
                return -1;
        }

        virt_dma_base = ioremap(dma_base, num_ports);
        if (virt_dma_base == NULL) {
                printk(KERN_ERR
                       "%s(%s) -- ERROR, Unable to map addresses 0x%lx to 0x%lx\n",
                       __FUNCTION__, hwif->name, dma_base, dma_base + num_ports - 1);
                goto dma_remap_failure;
        }
        hwif->dma_base = (unsigned long) virt_dma_base;

        hwif->dmatable_cpu = pci_alloc_consistent(dev,
                                          IOC4_PRD_ENTRIES * IOC4_PRD_BYTES,
                                          &hwif->dmatable_dma);

        if (!hwif->dmatable_cpu)
                goto dma_pci_alloc_failure;

        hwif->sg_max_nents = IOC4_PRD_ENTRIES;

        pad = pci_alloc_consistent(dev, IOC4_IDE_CACHELINE_SIZE,
                                   (dma_addr_t *) &(hwif->dma_status));

        if (pad) {
                ide_set_hwifdata(hwif, pad);
                return 0;
        }

        pci_free_consistent(dev, IOC4_PRD_ENTRIES * IOC4_PRD_BYTES,
                            hwif->dmatable_cpu, hwif->dmatable_dma);
        printk(KERN_INFO
               "%s() -- Error! Unable to allocate DMA Maps for drive %s\n",
               __FUNCTION__, hwif->name);
        printk(KERN_INFO
               "Changing from DMA to PIO mode for Drive %s\n", hwif->name);

dma_pci_alloc_failure:
        iounmap(virt_dma_base);

dma_remap_failure:
        release_mem_region(dma_base, num_ports);

        return -1;
}

/* Initializes the IOC4 DMA Engine */
static void
sgiioc4_configure_for_dma(int dma_direction, ide_drive_t * drive)
{
        u32 ioc4_dma;
        ide_hwif_t *hwif = HWIF(drive);
        unsigned long dma_base = hwif->dma_base;
        unsigned long ioc4_dma_addr = dma_base + IOC4_DMA_CTRL * 4;
        u32 dma_addr, ending_dma_addr;

        ioc4_dma = readl((void __iomem *)ioc4_dma_addr);

        if (ioc4_dma & IOC4_S_DMA_ACTIVE) {
                printk(KERN_WARNING
                        "%s(%s):Warning!! DMA from previous transfer was still active\n",
                       __FUNCTION__, drive->name);
                writel(IOC4_S_DMA_STOP, (void __iomem *)ioc4_dma_addr);
                ioc4_dma = sgiioc4_ide_dma_stop(hwif, dma_base);

                if (ioc4_dma & IOC4_S_DMA_STOP)
                        printk(KERN_ERR
                               "%s(%s) : IOC4 Dma STOP bit is still 1\n",
                               __FUNCTION__, drive->name);
        }

        ioc4_dma = readl((void __iomem *)ioc4_dma_addr);
        if (ioc4_dma & IOC4_S_DMA_ERROR) {
                printk(KERN_WARNING
                       "%s(%s) : Warning!! - DMA Error during Previous"
                       " transfer | status 0x%x\n",
                       __FUNCTION__, drive->name, ioc4_dma);
                writel(IOC4_S_DMA_STOP, (void __iomem *)ioc4_dma_addr);
                ioc4_dma = sgiioc4_ide_dma_stop(hwif, dma_base);

                if (ioc4_dma & IOC4_S_DMA_STOP)
                        printk(KERN_ERR
                               "%s(%s) : IOC4 DMA STOP bit is still 1\n",
                               __FUNCTION__, drive->name);
        }

        /* Address of the Scatter Gather List */
        dma_addr = cpu_to_le32(hwif->dmatable_dma);
        writel(dma_addr, (void __iomem *)(dma_base + IOC4_DMA_PTR_L * 4));

        /* Address of the Ending DMA */
        memset(ide_get_hwifdata(hwif), 0, IOC4_IDE_CACHELINE_SIZE);
        ending_dma_addr = cpu_to_le32(hwif->dma_status);
        writel(ending_dma_addr, (void __iomem *)(dma_base + IOC4_DMA_END_ADDR * 4));

        writel(dma_direction, (void __iomem *)ioc4_dma_addr);
        drive->waiting_for_dma = 1;
}

/* IOC4 Scatter Gather list Format                                       */
/* 128 Bit entries to support 64 bit addresses in the future             */
/* The Scatter Gather list Entry should be in the BIG-ENDIAN Format      */
/* --------------------------------------------------------------------- */
/* | Upper 32 bits - Zero           |           Lower 32 bits- address | */
/* --------------------------------------------------------------------- */
/* | Upper 32 bits - Zero           |EOL| 15 unused     | 16 Bit Length| */
/* --------------------------------------------------------------------- */
/* Creates the scatter gather list, DMA Table */
static unsigned int
sgiioc4_build_dma_table(ide_drive_t * drive, struct request *rq, int ddir)
{
        ide_hwif_t *hwif = HWIF(drive);
        unsigned int *table = hwif->dmatable_cpu;
        unsigned int count = 0, i = 1;
        struct scatterlist *sg;

        hwif->sg_nents = i = ide_build_sglist(drive, rq);

        if (!i)
                return 0;       /* sglist of length Zero */

        sg = hwif->sg_table;
        while (i && sg_dma_len(sg)) {
                dma_addr_t cur_addr;
                int cur_len;
                cur_addr = sg_dma_address(sg);
                cur_len = sg_dma_len(sg);

                while (cur_len) {
                        if (count++ >= IOC4_PRD_ENTRIES) {
                                printk(KERN_WARNING
                                       "%s: DMA table too small\n",
                                       drive->name);
                                goto use_pio_instead;
                        } else {
                                u32 bcount =
                                    0x10000 - (cur_addr & 0xffff);

                                if (bcount > cur_len)
                                        bcount = cur_len;

                                /* put the addr, length in
                                 * the IOC4 dma-table format */
                                *table = 0x0;
                                table++;
                                *table = cpu_to_be32(cur_addr);
                                table++;
                                *table = 0x0;
                                table++;

                                *table = cpu_to_be32(bcount);
                                table++;

                                cur_addr += bcount;
                                cur_len -= bcount;
                        }
                }

                sg = sg_next(sg);
                i--;
        }

        if (count) {
                table--;
                *table |= cpu_to_be32(0x80000000);
                return count;
        }

use_pio_instead:
        ide_destroy_dmatable(drive);

        return 0;               /* revert to PIO for this request */
}

static int sgiioc4_ide_dma_setup(ide_drive_t *drive)
{
        struct request *rq = HWGROUP(drive)->rq;
        unsigned int count = 0;
        int ddir;

        if (rq_data_dir(rq))
                ddir = PCI_DMA_TODEVICE;
        else
                ddir = PCI_DMA_FROMDEVICE;

        if (!(count = sgiioc4_build_dma_table(drive, rq, ddir))) {
                /* try PIO instead of DMA */
                ide_map_sg(drive, rq);
                return 1;
        }

        if (rq_data_dir(rq))
                /* Writes TO the IOC4 FROM Main Memory */
                ddir = IOC4_DMA_READ;
        else
                /* Writes FROM the IOC4 TO Main Memory */
                ddir = IOC4_DMA_WRITE;

        sgiioc4_configure_for_dma(ddir, drive);

        return 0;
}

static void __devinit
ide_init_sgiioc4(ide_hwif_t * hwif)
{
        hwif->mmio = 1;
        hwif->set_pio_mode = NULL; /* Sets timing for PIO mode */
        hwif->set_dma_mode = &sgiioc4_set_dma_mode;
        hwif->selectproc = NULL;/* Use the default routine to select drive */
        hwif->reset_poll = NULL;/* No HBA specific reset_poll needed */
        hwif->pre_reset = NULL; /* No HBA specific pre_set needed */
        hwif->resetproc = &sgiioc4_resetproc;/* Reset DMA engine,
                                                clear interrupts */
        hwif->maskproc = &sgiioc4_maskproc;     /* Mask on/off NIEN register */
        hwif->quirkproc = NULL;

        hwif->INB = &sgiioc4_INB;

        if (hwif->dma_base == 0)
                return;

        hwif->dma_host_set = &sgiioc4_dma_host_set;
        hwif->dma_setup = &sgiioc4_ide_dma_setup;
        hwif->dma_start = &sgiioc4_ide_dma_start;
        hwif->ide_dma_end = &sgiioc4_ide_dma_end;
        hwif->ide_dma_test_irq = &sgiioc4_ide_dma_test_irq;
        hwif->dma_lost_irq = &sgiioc4_dma_lost_irq;
        hwif->dma_timeout = &ide_dma_timeout;
}

static const struct ide_port_info sgiioc4_port_info __devinitdata = {
        .chipset                = ide_pci,
        .host_flags             = IDE_HFLAG_NO_DMA | /* no SFF-style DMA */
                                  IDE_HFLAG_NO_AUTOTUNE,
        .mwdma_mask             = ATA_MWDMA2_ONLY,
};

static int __devinit
sgiioc4_ide_setup_pci_device(struct pci_dev *dev)
{
        unsigned long cmd_base, dma_base, irqport;
        unsigned long bar0, cmd_phys_base, ctl;
        void __iomem *virt_base;
        ide_hwif_t *hwif;
        int h;
        u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };
        hw_regs_t hw;
        struct ide_port_info d = sgiioc4_port_info;

        /*
         * Find an empty HWIF; if none available, return -ENOMEM.
         */
        for (h = 0; h < MAX_HWIFS; ++h) {
                hwif = &ide_hwifs[h];
                if (hwif->chipset == ide_unknown)
                        break;
        }
        if (h == MAX_HWIFS) {
                printk(KERN_ERR "%s: too many IDE interfaces, no room in table\n",
                                DRV_NAME);
                return -ENOMEM;
        }

        /*  Get the CmdBlk and CtrlBlk Base Registers */
        bar0 = pci_resource_start(dev, 0);
        virt_base = ioremap(bar0, pci_resource_len(dev, 0));
        if (virt_base == NULL) {
                printk(KERN_ERR "%s: Unable to remap BAR 0 address: 0x%lx\n",
                                DRV_NAME, bar0);
                return -ENOMEM;
        }
        cmd_base = (unsigned long) virt_base + IOC4_CMD_OFFSET;
        ctl = (unsigned long) virt_base + IOC4_CTRL_OFFSET;
        irqport = (unsigned long) virt_base + IOC4_INTR_OFFSET;
        dma_base = pci_resource_start(dev, 0) + IOC4_DMA_OFFSET;

        cmd_phys_base = bar0 + IOC4_CMD_OFFSET;
        if (!request_mem_region(cmd_phys_base, IOC4_CMD_CTL_BLK_SIZE,
            hwif->name)) {
                printk(KERN_ERR
                        "%s : %s -- ERROR, Addresses "
                        "0x%p to 0x%p ALREADY in use\n",
                       __FUNCTION__, hwif->name, (void *) cmd_phys_base,
                       (void *) cmd_phys_base + IOC4_CMD_CTL_BLK_SIZE);
                return -ENOMEM;
        }

        /* Initialize the IO registers */
        memset(&hw, 0, sizeof(hw));
        sgiioc4_init_hwif_ports(&hw, cmd_base, ctl, irqport);
        hw.irq = dev->irq;
        hw.chipset = ide_pci;
        hw.dev = &dev->dev;
        ide_init_port_hw(hwif, &hw);

        hwif->dev = &dev->dev;

        /* The IOC4 uses MMIO rather than Port IO. */
        default_hwif_mmiops(hwif);

        /* Initializing chipset IRQ Registers */
        writel(0x03, (void __iomem *)(irqport + IOC4_INTR_SET * 4));

        if (dma_base == 0 || ide_dma_sgiioc4(hwif, dma_base)) {
                printk(KERN_INFO "%s: %s Bus-Master DMA disabled\n",
                                 hwif->name, DRV_NAME);
                d.mwdma_mask = 0;
        }

        ide_init_sgiioc4(hwif);

        idx[0] = hwif->index;

        if (ide_device_add(idx, &d))
                return -EIO;

        return 0;
}

static unsigned int __devinit
pci_init_sgiioc4(struct pci_dev *dev)
{
        int ret;

        printk(KERN_INFO "%s: IDE controller at PCI slot %s, revision %d\n",
                         DRV_NAME, pci_name(dev), dev->revision);

        if (dev->revision < IOC4_SUPPORTED_FIRMWARE_REV) {
                printk(KERN_ERR "Skipping %s IDE controller in slot %s: "
                                "firmware is obsolete - please upgrade to "
                                "revision46 or higher\n",
                                DRV_NAME, pci_name(dev));
                ret = -EAGAIN;
                goto out;
        }
        ret = sgiioc4_ide_setup_pci_device(dev);
out:
        return ret;
}

int
ioc4_ide_attach_one(struct ioc4_driver_data *idd)
{
        /* PCI-RT does not bring out IDE connection.
         * Do not attach to this particular IOC4.
         */
        if (idd->idd_variant == IOC4_VARIANT_PCI_RT)
                return 0;

        return pci_init_sgiioc4(idd->idd_pdev);
}

static struct ioc4_submodule ioc4_ide_submodule = {
        .is_name = "IOC4_ide",
        .is_owner = THIS_MODULE,
        .is_probe = ioc4_ide_attach_one,
/*      .is_remove = ioc4_ide_remove_one,       */
};

static int __init ioc4_ide_init(void)
{
        return ioc4_register_submodule(&ioc4_ide_submodule);
}

late_initcall(ioc4_ide_init); /* Call only after IDE init is done */

MODULE_AUTHOR("Aniket Malatpure/Jeremy Higdon");
MODULE_DESCRIPTION("IDE PCI driver module for SGI IOC4 Base-IO Card");
MODULE_LICENSE("GPL");