2 # Touchscreen driver configuration
4 menuconfig INPUT_TOUCHSCREEN
7 Say Y here, and a list of supported touchscreens will be displayed.
8 This option doesn't affect the kernel.
14 config TOUCHSCREEN_88PM860X
15 tristate "Marvell 88PM860x touchscreen"
16 depends on MFD_88PM860X
18 Say Y here if you have a 88PM860x PMIC and want to enable
19 support for the built-in touchscreen.
23 To compile this driver as a module, choose M here: the
24 module will be called 88pm860x-ts.
26 config TOUCHSCREEN_ADS7846
27 tristate "ADS7846/TSC2046/AD7873 and AD(S)7843 based touchscreens"
29 depends on HWMON = n || HWMON
31 Say Y here if you have a touchscreen interface using the
32 ADS7846/TSC2046/AD7873 or ADS7843/AD7843 controller,
33 and your board-specific setup code includes that in its
36 If HWMON is selected, and the driver is told the reference voltage
37 on your board, you will also get hwmon interfaces for the voltage
38 (and on ads7846/tsc2046/ad7873, temperature) sensors of this chip.
40 If unsure, say N (but it's safe to say "Y").
42 To compile this driver as a module, choose M here: the
43 module will be called ads7846.
45 config TOUCHSCREEN_AD7877
46 tristate "AD7877 based touchscreens"
49 Say Y here if you have a touchscreen interface using the
50 AD7877 controller, and your board-specific initialization
51 code includes that in its table of SPI devices.
53 If unsure, say N (but it's safe to say "Y").
55 To compile this driver as a module, choose M here: the
56 module will be called ad7877.
58 config TOUCHSCREEN_AD7879
59 tristate "Analog Devices AD7879-1/AD7889-1 touchscreen interface"
61 Say Y here if you want to support a touchscreen interface using
62 the AD7879-1/AD7889-1 controller.
64 You should select a bus connection too.
66 To compile this driver as a module, choose M here: the
67 module will be called ad7879.
69 config TOUCHSCREEN_AD7879_I2C
70 tristate "support I2C bus connection"
71 depends on TOUCHSCREEN_AD7879 && I2C
73 Say Y here if you have AD7879-1/AD7889-1 hooked to an I2C bus.
75 To compile this driver as a module, choose M here: the
76 module will be called ad7879-i2c.
78 config TOUCHSCREEN_AD7879_SPI
79 tristate "support SPI bus connection"
80 depends on TOUCHSCREEN_AD7879 && SPI_MASTER
82 Say Y here if you have AD7879-1/AD7889-1 hooked to a SPI bus.
84 If unsure, say N (but it's safe to say "Y").
86 To compile this driver as a module, choose M here: the
87 module will be called ad7879-spi.
89 config TOUCHSCREEN_ATMEL_MXT
90 tristate "Atmel mXT I2C Touchscreen"
93 Say Y here if you have Atmel mXT series I2C touchscreen,
94 such as AT42QT602240/ATMXT224, connected to your system.
98 To compile this driver as a module, choose M here: the
99 module will be called atmel_mxt_ts.
101 config TOUCHSCREEN_AUO_PIXCIR
102 tristate "AUO in-cell touchscreen using Pixcir ICs"
106 Say Y here if you have a AUO display with in-cell touchscreen
111 To compile this driver as a module, choose M here: the
112 module will be called auo-pixcir-ts.
114 config TOUCHSCREEN_BU21013
115 tristate "BU21013 based touch panel controllers"
118 Say Y here if you have a bu21013 touchscreen connected to
123 To compile this driver as a module, choose M here: the
124 module will be called bu21013_ts.
126 config TOUCHSCREEN_CY8CTMG110
127 tristate "cy8ctmg110 touchscreen"
131 Say Y here if you have a cy8ctmg110 capacitive touchscreen on
136 To compile this driver as a module, choose M here: the
137 module will be called cy8ctmg110_ts.
139 config TOUCHSCREEN_CYTTSP_CORE
140 tristate "Cypress TTSP touchscreen"
142 Say Y here if you have a touchscreen using controller from
143 the Cypress TrueTouch(tm) Standard Product family connected
144 to your system. You will also need to select appropriate
145 bus connection below.
149 To compile this driver as a module, choose M here: the
150 module will be called cyttsp_core.
152 config TOUCHSCREEN_CYTTSP_I2C
153 tristate "support I2C bus connection"
154 depends on TOUCHSCREEN_CYTTSP_CORE && I2C
156 Say Y here if the touchscreen is connected via I2C bus.
158 To compile this driver as a module, choose M here: the
159 module will be called cyttsp_i2c.
161 config TOUCHSCREEN_CYTTSP_SPI
162 tristate "support SPI bus connection"
163 depends on TOUCHSCREEN_CYTTSP_CORE && SPI_MASTER
165 Say Y here if the touchscreen is connected via SPI bus.
167 To compile this driver as a module, choose M here: the
168 module will be called cyttsp_spi.
170 config TOUCHSCREEN_CYTTSP4_CORE
171 tristate "Cypress TrueTouch Gen4 Touchscreen Driver"
173 Core driver for Cypress TrueTouch(tm) Standard Product
174 Generation4 touchscreen controllers.
176 Say Y here if you have a Cypress Gen4 touchscreen.
180 To compile this driver as a module, choose M here.
182 config TOUCHSCREEN_CYTTSP4_I2C
183 tristate "support I2C bus connection"
184 depends on TOUCHSCREEN_CYTTSP4_CORE && I2C
186 Say Y here if the touchscreen is connected via I2C bus.
188 To compile this driver as a module, choose M here: the
189 module will be called cyttsp4_i2c.
191 config TOUCHSCREEN_CYTTSP4_SPI
192 tristate "support SPI bus connection"
193 depends on TOUCHSCREEN_CYTTSP4_CORE && SPI_MASTER
195 Say Y here if the touchscreen is connected via SPI bus.
197 To compile this driver as a module, choose M here: the
198 module will be called cyttsp4_spi.
200 config TOUCHSCREEN_DA9034
201 tristate "Touchscreen support for Dialog Semiconductor DA9034"
202 depends on PMIC_DA903X
205 Say Y here to enable the support for the touchscreen found
206 on Dialog Semiconductor DA9034 PMIC.
210 To compile this driver as a module, choose M here: the
211 module will be called da9034-ts.
213 config TOUCHSCREEN_DA9052
214 tristate "Dialog DA9052/DA9053 TSI"
215 depends on PMIC_DA9052
217 Say Y here to support the touchscreen found on Dialog Semiconductor
218 DA9052-BC and DA9053-AA/Bx PMICs.
222 To compile this driver as a module, choose M here: the
223 module will be called da9052_tsi.
225 config TOUCHSCREEN_DYNAPRO
226 tristate "Dynapro serial touchscreen"
229 Say Y here if you have a Dynapro serial touchscreen connected to
234 To compile this driver as a module, choose M here: the
235 module will be called dynapro.
237 config TOUCHSCREEN_HAMPSHIRE
238 tristate "Hampshire serial touchscreen"
241 Say Y here if you have a Hampshire serial touchscreen connected to
246 To compile this driver as a module, choose M here: the
247 module will be called hampshire.
249 config TOUCHSCREEN_EETI
250 tristate "EETI touchscreen panel support"
253 Say Y here to enable support for I2C connected EETI touch panels.
255 To compile this driver as a module, choose M here: the
256 module will be called eeti_ts.
258 config TOUCHSCREEN_EGALAX
259 tristate "EETI eGalax multi-touch panel support"
262 Say Y here to enable support for I2C connected EETI
263 eGalax multi-touch panels.
265 To compile this driver as a module, choose M here: the
266 module will be called egalax_ts.
268 config TOUCHSCREEN_FUJITSU
269 tristate "Fujitsu serial touchscreen"
272 Say Y here if you have the Fujitsu touchscreen (such as one
273 installed in Lifebook P series laptop) connected to your
278 To compile this driver as a module, choose M here: the
279 module will be called fujitsu-ts.
281 config TOUCHSCREEN_ILI210X
282 tristate "Ilitek ILI210X based touchscreen"
285 Say Y here if you have a ILI210X based touchscreen
286 controller. This driver supports models ILI2102,
287 ILI2102s, ILI2103, ILI2103s and ILI2105.
288 Such kind of chipsets can be found in Amazon Kindle Fire
293 To compile this driver as a module, choose M here: the
294 module will be called ili210x.
296 config TOUCHSCREEN_S3C2410
297 tristate "Samsung S3C2410/generic touchscreen input driver"
298 depends on ARCH_S3C24XX || SAMSUNG_DEV_TS
301 Say Y here if you have the s3c2410 touchscreen.
305 To compile this driver as a module, choose M here: the
306 module will be called s3c2410_ts.
308 config TOUCHSCREEN_GUNZE
309 tristate "Gunze AHL-51S touchscreen"
312 Say Y here if you have the Gunze AHL-51 touchscreen connected to
317 To compile this driver as a module, choose M here: the
318 module will be called gunze.
320 config TOUCHSCREEN_ELO
321 tristate "Elo serial touchscreens"
324 Say Y here if you have an Elo serial touchscreen connected to
329 To compile this driver as a module, choose M here: the
330 module will be called elo.
332 config TOUCHSCREEN_WACOM_W8001
333 tristate "Wacom W8001 penabled serial touchscreen"
336 Say Y here if you have an Wacom W8001 penabled serial touchscreen
337 connected to your system.
341 To compile this driver as a module, choose M here: the
342 module will be called wacom_w8001.
344 config TOUCHSCREEN_WACOM_I2C
345 tristate "Wacom Tablet support (I2C)"
348 Say Y here if you want to use the I2C version of the Wacom
353 To compile this driver as a module, choose M here: the module
354 will be called wacom_i2c.
356 config TOUCHSCREEN_LPC32XX
357 tristate "LPC32XX touchscreen controller"
358 depends on ARCH_LPC32XX
360 Say Y here if you have a LPC32XX device and want
361 to support the built-in touchscreen.
363 To compile this driver as a module, choose M here: the
364 module will be called lpc32xx_ts.
366 config TOUCHSCREEN_MAX11801
367 tristate "MAX11801 based touchscreens"
370 Say Y here if you have a MAX11801 based touchscreen
375 To compile this driver as a module, choose M here: the
376 module will be called max11801_ts.
378 config TOUCHSCREEN_MCS5000
379 tristate "MELFAS MCS-5000 touchscreen"
382 Say Y here if you have the MELFAS MCS-5000 touchscreen controller
387 To compile this driver as a module, choose M here: the
388 module will be called mcs5000_ts.
390 config TOUCHSCREEN_MMS114
391 tristate "MELFAS MMS114 touchscreen"
394 Say Y here if you have the MELFAS MMS114 touchscreen controller
399 To compile this driver as a module, choose M here: the
400 module will be called mms114.
402 config TOUCHSCREEN_MTOUCH
403 tristate "MicroTouch serial touchscreens"
406 Say Y here if you have a MicroTouch (3M) serial touchscreen connected to
411 To compile this driver as a module, choose M here: the
412 module will be called mtouch.
414 config TOUCHSCREEN_INEXIO
415 tristate "iNexio serial touchscreens"
418 Say Y here if you have an iNexio serial touchscreen connected to
423 To compile this driver as a module, choose M here: the
424 module will be called inexio.
426 config TOUCHSCREEN_INTEL_MID
427 tristate "Intel MID platform resistive touchscreen"
428 depends on INTEL_SCU_IPC
430 Say Y here if you have a Intel MID based touchscreen in
435 To compile this driver as a module, choose M here: the
436 module will be called intel_mid_touch.
438 config TOUCHSCREEN_MK712
439 tristate "ICS MicroClock MK712 touchscreen"
441 Say Y here if you have the ICS MicroClock MK712 touchscreen
442 controller chip in your system.
446 To compile this driver as a module, choose M here: the
447 module will be called mk712.
449 config TOUCHSCREEN_HP600
450 tristate "HP Jornada 6xx touchscreen"
451 depends on SH_HP6XX && SH_ADC
453 Say Y here if you have a HP Jornada 620/660/680/690 and want to
454 support the built-in touchscreen.
456 To compile this driver as a module, choose M here: the
457 module will be called hp680_ts_input.
459 config TOUCHSCREEN_HP7XX
460 tristate "HP Jornada 7xx touchscreen"
461 depends on SA1100_JORNADA720_SSP
463 Say Y here if you have a HP Jornada 710/720/728 and want
464 to support the built-in touchscreen.
466 To compile this driver as a module, choose M here: the
467 module will be called jornada720_ts.
469 config TOUCHSCREEN_HTCPEN
470 tristate "HTC Shift X9500 touchscreen"
473 Say Y here if you have an HTC Shift UMPC also known as HTC X9500
474 Clio / Shangrila and want to support the built-in touchscreen.
478 To compile this driver as a module, choose M here: the
479 module will be called htcpen.
481 config TOUCHSCREEN_PENMOUNT
482 tristate "Penmount serial touchscreen"
485 Say Y here if you have a Penmount serial touchscreen connected to
490 To compile this driver as a module, choose M here: the
491 module will be called penmount.
493 config TOUCHSCREEN_EDT_FT5X06
494 tristate "EDT FocalTech FT5x06 I2C Touchscreen support"
497 Say Y here if you have an EDT "Polytouch" touchscreen based
498 on the FocalTech FT5x06 family of controllers connected to
503 To compile this driver as a module, choose M here: the
504 module will be called edt-ft5x06.
506 config TOUCHSCREEN_MIGOR
507 tristate "Renesas MIGO-R touchscreen"
508 depends on SH_MIGOR && I2C
510 Say Y here to enable MIGO-R touchscreen support.
514 To compile this driver as a module, choose M here: the
515 module will be called migor_ts.
517 config TOUCHSCREEN_TOUCHRIGHT
518 tristate "Touchright serial touchscreen"
521 Say Y here if you have a Touchright serial touchscreen connected to
526 To compile this driver as a module, choose M here: the
527 module will be called touchright.
529 config TOUCHSCREEN_TOUCHWIN
530 tristate "Touchwin serial touchscreen"
533 Say Y here if you have a Touchwin serial touchscreen connected to
538 To compile this driver as a module, choose M here: the
539 module will be called touchwin.
541 config TOUCHSCREEN_TI_AM335X_TSC
542 tristate "TI Touchscreen Interface"
543 depends on MFD_TI_AM335X_TSCADC
545 Say Y here if you have 4/5/8 wire touchscreen controller
546 to be connected to the ADC controller on your TI AM335x SoC.
550 To compile this driver as a module, choose M here: the
551 module will be called ti_am335x_tsc.
553 config TOUCHSCREEN_ATMEL_TSADCC
554 tristate "Atmel Touchscreen Interface"
557 Say Y here if you have a 4-wire touchscreen connected to the
558 ADC Controller on your Atmel SoC.
562 To compile this driver as a module, choose M here: the
563 module will be called atmel_tsadcc.
565 config TOUCHSCREEN_UCB1400
566 tristate "Philips UCB1400 touchscreen"
568 depends on UCB1400_CORE
570 This enables support for the Philips UCB1400 touchscreen interface.
571 The UCB1400 is an AC97 audio codec. The touchscreen interface
572 will be initialized only after the ALSA subsystem has been
573 brought up and the UCB1400 detected. You therefore have to
574 configure ALSA support as well (either built-in or modular,
575 independently of whether this driver is itself built-in or
576 modular) for this driver to work.
578 To compile this driver as a module, choose M here: the
579 module will be called ucb1400_ts.
581 config TOUCHSCREEN_PIXCIR
582 tristate "PIXCIR I2C touchscreens"
585 Say Y here if you have a pixcir i2c touchscreen
590 To compile this driver as a module, choose M here: the
591 module will be called pixcir_i2c_ts.
593 config TOUCHSCREEN_WM831X
594 tristate "Support for WM831x touchscreen controllers"
595 depends on MFD_WM831X
597 This enables support for the touchscreen controller on the WM831x
600 To compile this driver as a module, choose M here: the
601 module will be called wm831x-ts.
603 config TOUCHSCREEN_WM97XX
604 tristate "Support for WM97xx AC97 touchscreen controllers"
607 Say Y here if you have a Wolfson Microelectronics WM97xx
608 touchscreen connected to your system. Note that this option
609 only enables core driver, you will also need to select
610 support for appropriate chip below.
614 To compile this driver as a module, choose M here: the
615 module will be called wm97xx-ts.
617 config TOUCHSCREEN_WM9705
618 bool "WM9705 Touchscreen interface support"
619 depends on TOUCHSCREEN_WM97XX
622 Say Y here to enable support for the Wolfson Microelectronics
623 WM9705 touchscreen controller.
625 config TOUCHSCREEN_WM9712
626 bool "WM9712 Touchscreen interface support"
627 depends on TOUCHSCREEN_WM97XX
630 Say Y here to enable support for the Wolfson Microelectronics
631 WM9712 touchscreen controller.
633 config TOUCHSCREEN_WM9713
634 bool "WM9713 Touchscreen interface support"
635 depends on TOUCHSCREEN_WM97XX
638 Say Y here to enable support for the Wolfson Microelectronics
639 WM9713 touchscreen controller.
641 config TOUCHSCREEN_WM97XX_ATMEL
642 tristate "WM97xx Atmel accelerated touch"
643 depends on TOUCHSCREEN_WM97XX && (AVR32 || ARCH_AT91)
645 Say Y here for support for streaming mode with WM97xx touchscreens
646 on Atmel AT91 or AVR32 systems with an AC97C module.
648 Be aware that this will use channel B in the controller for
649 streaming data, this must not conflict with other AC97C drivers.
653 To compile this driver as a module, choose M here: the module will
654 be called atmel-wm97xx.
656 config TOUCHSCREEN_WM97XX_MAINSTONE
657 tristate "WM97xx Mainstone/Palm accelerated touch"
658 depends on TOUCHSCREEN_WM97XX && ARCH_PXA
660 Say Y here for support for streaming mode with WM97xx touchscreens
661 on Mainstone, Palm Tungsten T5, TX and LifeDrive systems.
665 To compile this driver as a module, choose M here: the
666 module will be called mainstone-wm97xx.
668 config TOUCHSCREEN_WM97XX_ZYLONITE
669 tristate "Zylonite accelerated touch"
670 depends on TOUCHSCREEN_WM97XX && MACH_ZYLONITE
671 select TOUCHSCREEN_WM9713
673 Say Y here for support for streaming mode with the touchscreen
678 To compile this driver as a module, choose M here: the
679 module will be called zylonite-wm97xx.
681 config TOUCHSCREEN_USB_COMPOSITE
682 tristate "USB Touchscreen Driver"
683 depends on USB_ARCH_HAS_HCD
686 USB Touchscreen driver for:
687 - eGalax Touchkit USB (also includes eTurboTouch CT-410/510/700)
688 - PanJit TouchSet USB
689 - 3M MicroTouch USB (EX II series)
691 - some other eTurboTouch
694 - IRTOUCHSYSTEMS/UNITOP
696 - GoTop Super_Q2/GogoPen/PenPower tablets
697 - JASTEC USB Touch Controller/DigiTech DTR-02U
698 - Zytronic controllers
699 - Elo TouchSystems 2700 IntelliTouch
700 - EasyTouch USB Touch Controller from Data Modul
701 - e2i (Mimo monitors)
703 Have a look at <http://linux.chapter7.ch/touchkit/> for
704 a usage description and the required user-space stuff.
706 To compile this driver as a module, choose M here: the
707 module will be called usbtouchscreen.
709 config TOUCHSCREEN_MC13783
710 tristate "Freescale MC13783 touchscreen input driver"
711 depends on MFD_MC13XXX
713 Say Y here if you have an Freescale MC13783 PMIC on your
714 board and want to use its touchscreen
718 To compile this driver as a module, choose M here: the
719 module will be called mc13783_ts.
721 config TOUCHSCREEN_USB_EGALAX
723 bool "eGalax, eTurboTouch CT-410/510/700 device support" if EXPERT
724 depends on TOUCHSCREEN_USB_COMPOSITE
726 config TOUCHSCREEN_USB_PANJIT
728 bool "PanJit device support" if EXPERT
729 depends on TOUCHSCREEN_USB_COMPOSITE
731 config TOUCHSCREEN_USB_3M
733 bool "3M/Microtouch EX II series device support" if EXPERT
734 depends on TOUCHSCREEN_USB_COMPOSITE
736 config TOUCHSCREEN_USB_ITM
738 bool "ITM device support" if EXPERT
739 depends on TOUCHSCREEN_USB_COMPOSITE
741 config TOUCHSCREEN_USB_ETURBO
743 bool "eTurboTouch (non-eGalax compatible) device support" if EXPERT
744 depends on TOUCHSCREEN_USB_COMPOSITE
746 config TOUCHSCREEN_USB_GUNZE
748 bool "Gunze AHL61 device support" if EXPERT
749 depends on TOUCHSCREEN_USB_COMPOSITE
751 config TOUCHSCREEN_USB_DMC_TSC10
753 bool "DMC TSC-10/25 device support" if EXPERT
754 depends on TOUCHSCREEN_USB_COMPOSITE
756 config TOUCHSCREEN_USB_IRTOUCH
758 bool "IRTOUCHSYSTEMS/UNITOP device support" if EXPERT
759 depends on TOUCHSCREEN_USB_COMPOSITE
761 config TOUCHSCREEN_USB_IDEALTEK
763 bool "IdealTEK URTC1000 device support" if EXPERT
764 depends on TOUCHSCREEN_USB_COMPOSITE
766 config TOUCHSCREEN_USB_GENERAL_TOUCH
768 bool "GeneralTouch Touchscreen device support" if EXPERT
769 depends on TOUCHSCREEN_USB_COMPOSITE
771 config TOUCHSCREEN_USB_GOTOP
773 bool "GoTop Super_Q2/GogoPen/PenPower tablet device support" if EXPERT
774 depends on TOUCHSCREEN_USB_COMPOSITE
776 config TOUCHSCREEN_USB_JASTEC
778 bool "JASTEC/DigiTech DTR-02U USB touch controller device support" if EXPERT
779 depends on TOUCHSCREEN_USB_COMPOSITE
781 config TOUCHSCREEN_USB_ELO
783 bool "Elo TouchSystems 2700 IntelliTouch controller device support" if EXPERT
784 depends on TOUCHSCREEN_USB_COMPOSITE
786 config TOUCHSCREEN_USB_E2I
788 bool "e2i Touchscreen controller (e.g. from Mimo 740)" if EXPERT
789 depends on TOUCHSCREEN_USB_COMPOSITE
791 config TOUCHSCREEN_USB_ZYTRONIC
793 bool "Zytronic controller" if EXPERT
794 depends on TOUCHSCREEN_USB_COMPOSITE
796 config TOUCHSCREEN_USB_ETT_TC45USB
798 bool "ET&T USB series TC4UM/TC5UH touchscreen controller support" if EXPERT
799 depends on TOUCHSCREEN_USB_COMPOSITE
801 config TOUCHSCREEN_USB_NEXIO
803 bool "NEXIO/iNexio device support" if EXPERT
804 depends on TOUCHSCREEN_USB_COMPOSITE
806 config TOUCHSCREEN_USB_EASYTOUCH
808 bool "EasyTouch USB Touch controller device support" if EMBEDDED
809 depends on TOUCHSCREEN_USB_COMPOSITE
811 Say Y here if you have an EasyTouch USB Touch controller.
814 config TOUCHSCREEN_TOUCHIT213
815 tristate "Sahara TouchIT-213 touchscreen"
818 Say Y here if you have a Sahara TouchIT-213 Tablet PC.
822 To compile this driver as a module, choose M here: the
823 module will be called touchit213.
825 config TOUCHSCREEN_TSC_SERIO
826 tristate "TSC-10/25/40 serial touchscreen support"
829 Say Y here if you have a TSC-10, 25 or 40 serial touchscreen connected
834 To compile this driver as a module, choose M here: the
835 module will be called tsc40.
837 config TOUCHSCREEN_TSC2005
838 tristate "TSC2005 based touchscreens"
839 depends on SPI_MASTER
841 Say Y here if you have a TSC2005 based touchscreen.
845 To compile this driver as a module, choose M here: the
846 module will be called tsc2005.
848 config TOUCHSCREEN_TSC2007
849 tristate "TSC2007 based touchscreens"
852 Say Y here if you have a TSC2007 based touchscreen.
856 To compile this driver as a module, choose M here: the
857 module will be called tsc2007.
859 config TOUCHSCREEN_W90X900
860 tristate "W90P910 touchscreen driver"
861 depends on ARCH_W90X900
863 Say Y here if you have a W90P910 based touchscreen.
865 To compile this driver as a module, choose M here: the
866 module will be called w90p910_ts.
868 config TOUCHSCREEN_PCAP
869 tristate "Motorola PCAP touchscreen"
872 Say Y here if you have a Motorola EZX telephone and
873 want to enable support for the built-in touchscreen.
875 To compile this driver as a module, choose M here: the
876 module will be called pcap_ts.
878 config TOUCHSCREEN_ST1232
879 tristate "Sitronix ST1232 touchscreen controllers"
882 Say Y here if you want to support Sitronix ST1232
883 touchscreen controller.
887 To compile this driver as a module, choose M here: the
888 module will be called st1232_ts.
890 config TOUCHSCREEN_STMPE
891 tristate "STMicroelectronics STMPE touchscreens"
894 Say Y here if you want support for STMicroelectronics
895 STMPE touchscreen controllers.
897 To compile this driver as a module, choose M here: the
898 module will be called stmpe-ts.
900 config TOUCHSCREEN_SUN4I
901 tristate "Allwinner sun4i resistive touchscreen controller support"
902 depends on ARCH_SUNXI || COMPILE_TEST
904 This selects support for the resistive touchscreen controller
905 found on Allwinner sunxi SoCs.
907 To compile this driver as a module, choose M here: the
908 module will be called sun4i-ts.
910 config TOUCHSCREEN_SUR40
911 tristate "Samsung SUR40 (Surface 2.0/PixelSense) touchscreen"
915 Say Y here if you want support for the Samsung SUR40 touchscreen
916 (also known as Microsoft Surface 2.0 or Microsoft PixelSense).
918 To compile this driver as a module, choose M here: the
919 module will be called sur40.
921 config TOUCHSCREEN_TPS6507X
922 tristate "TPS6507x based touchscreens"
926 Say Y here if you have a TPS6507x based touchscreen
931 To compile this driver as a module, choose M here: the
932 module will be called tps6507x_ts.
934 config TOUCHSCREEN_ZFORCE
935 tristate "Neonode zForce infrared touchscreens"
939 Say Y here if you have a touchscreen using the zforce
940 infraread technology from Neonode.
944 To compile this driver as a module, choose M here: the
945 module will be called zforce_ts.