2 # Touchscreen driver configuration
4 menuconfig INPUT_TOUCHSCREEN
7 Say Y here, and a list of supported touchscreens will be displayed.
8 This option doesn't affect the kernel.
16 depends on INPUT && OF
18 config TOUCHSCREEN_88PM860X
19 tristate "Marvell 88PM860x touchscreen"
20 depends on MFD_88PM860X
22 Say Y here if you have a 88PM860x PMIC and want to enable
23 support for the built-in touchscreen.
27 To compile this driver as a module, choose M here: the
28 module will be called 88pm860x-ts.
30 config TOUCHSCREEN_ADS7846
31 tristate "ADS7846/TSC2046/AD7873 and AD(S)7843 based touchscreens"
33 depends on HWMON = n || HWMON
35 Say Y here if you have a touchscreen interface using the
36 ADS7846/TSC2046/AD7873 or ADS7843/AD7843 controller,
37 and your board-specific setup code includes that in its
40 If HWMON is selected, and the driver is told the reference voltage
41 on your board, you will also get hwmon interfaces for the voltage
42 (and on ads7846/tsc2046/ad7873, temperature) sensors of this chip.
44 If unsure, say N (but it's safe to say "Y").
46 To compile this driver as a module, choose M here: the
47 module will be called ads7846.
49 config TOUCHSCREEN_AD7877
50 tristate "AD7877 based touchscreens"
53 Say Y here if you have a touchscreen interface using the
54 AD7877 controller, and your board-specific initialization
55 code includes that in its table of SPI devices.
57 If unsure, say N (but it's safe to say "Y").
59 To compile this driver as a module, choose M here: the
60 module will be called ad7877.
62 config TOUCHSCREEN_AD7879
63 tristate "Analog Devices AD7879-1/AD7889-1 touchscreen interface"
65 Say Y here if you want to support a touchscreen interface using
66 the AD7879-1/AD7889-1 controller.
68 You should select a bus connection too.
70 To compile this driver as a module, choose M here: the
71 module will be called ad7879.
73 config TOUCHSCREEN_AD7879_I2C
74 tristate "support I2C bus connection"
75 depends on TOUCHSCREEN_AD7879 && I2C
77 Say Y here if you have AD7879-1/AD7889-1 hooked to an I2C bus.
79 To compile this driver as a module, choose M here: the
80 module will be called ad7879-i2c.
82 config TOUCHSCREEN_AD7879_SPI
83 tristate "support SPI bus connection"
84 depends on TOUCHSCREEN_AD7879 && SPI_MASTER
86 Say Y here if you have AD7879-1/AD7889-1 hooked to a SPI bus.
88 If unsure, say N (but it's safe to say "Y").
90 To compile this driver as a module, choose M here: the
91 module will be called ad7879-spi.
93 config TOUCHSCREEN_ATMEL_MXT
94 tristate "Atmel mXT I2C Touchscreen"
98 Say Y here if you have Atmel mXT series I2C touchscreen,
99 such as AT42QT602240/ATMXT224, connected to your system.
103 To compile this driver as a module, choose M here: the
104 module will be called atmel_mxt_ts.
106 config TOUCHSCREEN_AUO_PIXCIR
107 tristate "AUO in-cell touchscreen using Pixcir ICs"
111 Say Y here if you have a AUO display with in-cell touchscreen
116 To compile this driver as a module, choose M here: the
117 module will be called auo-pixcir-ts.
119 config TOUCHSCREEN_BU21013
120 tristate "BU21013 based touch panel controllers"
123 Say Y here if you have a bu21013 touchscreen connected to
128 To compile this driver as a module, choose M here: the
129 module will be called bu21013_ts.
131 config TOUCHSCREEN_CY8CTMG110
132 tristate "cy8ctmg110 touchscreen"
136 Say Y here if you have a cy8ctmg110 capacitive touchscreen on
141 To compile this driver as a module, choose M here: the
142 module will be called cy8ctmg110_ts.
144 config TOUCHSCREEN_CYTTSP_CORE
145 tristate "Cypress TTSP touchscreen"
147 Say Y here if you have a touchscreen using controller from
148 the Cypress TrueTouch(tm) Standard Product family connected
149 to your system. You will also need to select appropriate
150 bus connection below.
154 To compile this driver as a module, choose M here: the
155 module will be called cyttsp_core.
157 config TOUCHSCREEN_CYTTSP_I2C
158 tristate "support I2C bus connection"
159 depends on TOUCHSCREEN_CYTTSP_CORE && I2C
161 Say Y here if the touchscreen is connected via I2C bus.
163 To compile this driver as a module, choose M here: the
164 module will be called cyttsp_i2c.
166 config TOUCHSCREEN_CYTTSP_SPI
167 tristate "support SPI bus connection"
168 depends on TOUCHSCREEN_CYTTSP_CORE && SPI_MASTER
170 Say Y here if the touchscreen is connected via SPI bus.
172 To compile this driver as a module, choose M here: the
173 module will be called cyttsp_spi.
175 config TOUCHSCREEN_CYTTSP4_CORE
176 tristate "Cypress TrueTouch Gen4 Touchscreen Driver"
178 Core driver for Cypress TrueTouch(tm) Standard Product
179 Generation4 touchscreen controllers.
181 Say Y here if you have a Cypress Gen4 touchscreen.
185 To compile this driver as a module, choose M here.
187 config TOUCHSCREEN_CYTTSP4_I2C
188 tristate "support I2C bus connection"
189 depends on TOUCHSCREEN_CYTTSP4_CORE && I2C
191 Say Y here if the touchscreen is connected via I2C bus.
193 To compile this driver as a module, choose M here: the
194 module will be called cyttsp4_i2c.
196 config TOUCHSCREEN_CYTTSP4_SPI
197 tristate "support SPI bus connection"
198 depends on TOUCHSCREEN_CYTTSP4_CORE && SPI_MASTER
200 Say Y here if the touchscreen is connected via SPI bus.
202 To compile this driver as a module, choose M here: the
203 module will be called cyttsp4_spi.
205 config TOUCHSCREEN_DA9034
206 tristate "Touchscreen support for Dialog Semiconductor DA9034"
207 depends on PMIC_DA903X
210 Say Y here to enable the support for the touchscreen found
211 on Dialog Semiconductor DA9034 PMIC.
215 To compile this driver as a module, choose M here: the
216 module will be called da9034-ts.
218 config TOUCHSCREEN_DA9052
219 tristate "Dialog DA9052/DA9053 TSI"
220 depends on PMIC_DA9052
222 Say Y here to support the touchscreen found on Dialog Semiconductor
223 DA9052-BC and DA9053-AA/Bx PMICs.
227 To compile this driver as a module, choose M here: the
228 module will be called da9052_tsi.
230 config TOUCHSCREEN_DYNAPRO
231 tristate "Dynapro serial touchscreen"
234 Say Y here if you have a Dynapro serial touchscreen connected to
239 To compile this driver as a module, choose M here: the
240 module will be called dynapro.
242 config TOUCHSCREEN_HAMPSHIRE
243 tristate "Hampshire serial touchscreen"
246 Say Y here if you have a Hampshire serial touchscreen connected to
251 To compile this driver as a module, choose M here: the
252 module will be called hampshire.
254 config TOUCHSCREEN_EETI
255 tristate "EETI touchscreen panel support"
258 Say Y here to enable support for I2C connected EETI touch panels.
260 To compile this driver as a module, choose M here: the
261 module will be called eeti_ts.
263 config TOUCHSCREEN_EGALAX
264 tristate "EETI eGalax multi-touch panel support"
267 Say Y here to enable support for I2C connected EETI
268 eGalax multi-touch panels.
270 To compile this driver as a module, choose M here: the
271 module will be called egalax_ts.
273 config TOUCHSCREEN_FUJITSU
274 tristate "Fujitsu serial touchscreen"
277 Say Y here if you have the Fujitsu touchscreen (such as one
278 installed in Lifebook P series laptop) connected to your
283 To compile this driver as a module, choose M here: the
284 module will be called fujitsu-ts.
286 config TOUCHSCREEN_ILI210X
287 tristate "Ilitek ILI210X based touchscreen"
290 Say Y here if you have a ILI210X based touchscreen
291 controller. This driver supports models ILI2102,
292 ILI2102s, ILI2103, ILI2103s and ILI2105.
293 Such kind of chipsets can be found in Amazon Kindle Fire
298 To compile this driver as a module, choose M here: the
299 module will be called ili210x.
301 config TOUCHSCREEN_S3C2410
302 tristate "Samsung S3C2410/generic touchscreen input driver"
303 depends on ARCH_S3C24XX || SAMSUNG_DEV_TS
306 Say Y here if you have the s3c2410 touchscreen.
310 To compile this driver as a module, choose M here: the
311 module will be called s3c2410_ts.
313 config TOUCHSCREEN_GUNZE
314 tristate "Gunze AHL-51S touchscreen"
317 Say Y here if you have the Gunze AHL-51 touchscreen connected to
322 To compile this driver as a module, choose M here: the
323 module will be called gunze.
325 config TOUCHSCREEN_ELO
326 tristate "Elo serial touchscreens"
329 Say Y here if you have an Elo serial touchscreen connected to
334 To compile this driver as a module, choose M here: the
335 module will be called elo.
337 config TOUCHSCREEN_WACOM_W8001
338 tristate "Wacom W8001 penabled serial touchscreen"
341 Say Y here if you have an Wacom W8001 penabled serial touchscreen
342 connected to your system.
346 To compile this driver as a module, choose M here: the
347 module will be called wacom_w8001.
349 config TOUCHSCREEN_WACOM_I2C
350 tristate "Wacom Tablet support (I2C)"
353 Say Y here if you want to use the I2C version of the Wacom
358 To compile this driver as a module, choose M here: the module
359 will be called wacom_i2c.
361 config TOUCHSCREEN_LPC32XX
362 tristate "LPC32XX touchscreen controller"
363 depends on ARCH_LPC32XX
365 Say Y here if you have a LPC32XX device and want
366 to support the built-in touchscreen.
368 To compile this driver as a module, choose M here: the
369 module will be called lpc32xx_ts.
371 config TOUCHSCREEN_MAX11801
372 tristate "MAX11801 based touchscreens"
375 Say Y here if you have a MAX11801 based touchscreen
380 To compile this driver as a module, choose M here: the
381 module will be called max11801_ts.
383 config TOUCHSCREEN_MCS5000
384 tristate "MELFAS MCS-5000 touchscreen"
387 Say Y here if you have the MELFAS MCS-5000 touchscreen controller
392 To compile this driver as a module, choose M here: the
393 module will be called mcs5000_ts.
395 config TOUCHSCREEN_MMS114
396 tristate "MELFAS MMS114 touchscreen"
399 Say Y here if you have the MELFAS MMS114 touchscreen controller
404 To compile this driver as a module, choose M here: the
405 module will be called mms114.
407 config TOUCHSCREEN_MTOUCH
408 tristate "MicroTouch serial touchscreens"
411 Say Y here if you have a MicroTouch (3M) serial touchscreen connected to
416 To compile this driver as a module, choose M here: the
417 module will be called mtouch.
419 config TOUCHSCREEN_INEXIO
420 tristate "iNexio serial touchscreens"
423 Say Y here if you have an iNexio serial touchscreen connected to
428 To compile this driver as a module, choose M here: the
429 module will be called inexio.
431 config TOUCHSCREEN_INTEL_MID
432 tristate "Intel MID platform resistive touchscreen"
433 depends on INTEL_SCU_IPC
435 Say Y here if you have a Intel MID based touchscreen in
440 To compile this driver as a module, choose M here: the
441 module will be called intel_mid_touch.
443 config TOUCHSCREEN_MK712
444 tristate "ICS MicroClock MK712 touchscreen"
446 Say Y here if you have the ICS MicroClock MK712 touchscreen
447 controller chip in your system.
451 To compile this driver as a module, choose M here: the
452 module will be called mk712.
454 config TOUCHSCREEN_HP600
455 tristate "HP Jornada 6xx touchscreen"
456 depends on SH_HP6XX && SH_ADC
458 Say Y here if you have a HP Jornada 620/660/680/690 and want to
459 support the built-in touchscreen.
461 To compile this driver as a module, choose M here: the
462 module will be called hp680_ts_input.
464 config TOUCHSCREEN_HP7XX
465 tristate "HP Jornada 7xx touchscreen"
466 depends on SA1100_JORNADA720_SSP
468 Say Y here if you have a HP Jornada 710/720/728 and want
469 to support the built-in touchscreen.
471 To compile this driver as a module, choose M here: the
472 module will be called jornada720_ts.
474 config TOUCHSCREEN_HTCPEN
475 tristate "HTC Shift X9500 touchscreen"
478 Say Y here if you have an HTC Shift UMPC also known as HTC X9500
479 Clio / Shangrila and want to support the built-in touchscreen.
483 To compile this driver as a module, choose M here: the
484 module will be called htcpen.
486 config TOUCHSCREEN_PENMOUNT
487 tristate "Penmount serial touchscreen"
490 Say Y here if you have a Penmount serial touchscreen connected to
495 To compile this driver as a module, choose M here: the
496 module will be called penmount.
498 config TOUCHSCREEN_EDT_FT5X06
499 tristate "EDT FocalTech FT5x06 I2C Touchscreen support"
502 Say Y here if you have an EDT "Polytouch" touchscreen based
503 on the FocalTech FT5x06 family of controllers connected to
508 To compile this driver as a module, choose M here: the
509 module will be called edt-ft5x06.
511 config TOUCHSCREEN_MIGOR
512 tristate "Renesas MIGO-R touchscreen"
513 depends on SH_MIGOR && I2C
515 Say Y here to enable MIGO-R touchscreen support.
519 To compile this driver as a module, choose M here: the
520 module will be called migor_ts.
522 config TOUCHSCREEN_TOUCHRIGHT
523 tristate "Touchright serial touchscreen"
526 Say Y here if you have a Touchright serial touchscreen connected to
531 To compile this driver as a module, choose M here: the
532 module will be called touchright.
534 config TOUCHSCREEN_TOUCHWIN
535 tristate "Touchwin serial touchscreen"
538 Say Y here if you have a Touchwin serial touchscreen connected to
543 To compile this driver as a module, choose M here: the
544 module will be called touchwin.
546 config TOUCHSCREEN_TI_AM335X_TSC
547 tristate "TI Touchscreen Interface"
548 depends on MFD_TI_AM335X_TSCADC
550 Say Y here if you have 4/5/8 wire touchscreen controller
551 to be connected to the ADC controller on your TI AM335x SoC.
555 To compile this driver as a module, choose M here: the
556 module will be called ti_am335x_tsc.
558 config TOUCHSCREEN_ATMEL_TSADCC
559 tristate "Atmel Touchscreen Interface"
562 Say Y here if you have a 4-wire touchscreen connected to the
563 ADC Controller on your Atmel SoC.
567 To compile this driver as a module, choose M here: the
568 module will be called atmel_tsadcc.
570 config TOUCHSCREEN_UCB1400
571 tristate "Philips UCB1400 touchscreen"
573 depends on UCB1400_CORE
575 This enables support for the Philips UCB1400 touchscreen interface.
576 The UCB1400 is an AC97 audio codec. The touchscreen interface
577 will be initialized only after the ALSA subsystem has been
578 brought up and the UCB1400 detected. You therefore have to
579 configure ALSA support as well (either built-in or modular,
580 independently of whether this driver is itself built-in or
581 modular) for this driver to work.
583 To compile this driver as a module, choose M here: the
584 module will be called ucb1400_ts.
586 config TOUCHSCREEN_PIXCIR
587 tristate "PIXCIR I2C touchscreens"
590 Say Y here if you have a pixcir i2c touchscreen
595 To compile this driver as a module, choose M here: the
596 module will be called pixcir_i2c_ts.
598 config TOUCHSCREEN_WM831X
599 tristate "Support for WM831x touchscreen controllers"
600 depends on MFD_WM831X
602 This enables support for the touchscreen controller on the WM831x
605 To compile this driver as a module, choose M here: the
606 module will be called wm831x-ts.
608 config TOUCHSCREEN_WM97XX
609 tristate "Support for WM97xx AC97 touchscreen controllers"
612 Say Y here if you have a Wolfson Microelectronics WM97xx
613 touchscreen connected to your system. Note that this option
614 only enables core driver, you will also need to select
615 support for appropriate chip below.
619 To compile this driver as a module, choose M here: the
620 module will be called wm97xx-ts.
622 config TOUCHSCREEN_WM9705
623 bool "WM9705 Touchscreen interface support"
624 depends on TOUCHSCREEN_WM97XX
627 Say Y here to enable support for the Wolfson Microelectronics
628 WM9705 touchscreen controller.
630 config TOUCHSCREEN_WM9712
631 bool "WM9712 Touchscreen interface support"
632 depends on TOUCHSCREEN_WM97XX
635 Say Y here to enable support for the Wolfson Microelectronics
636 WM9712 touchscreen controller.
638 config TOUCHSCREEN_WM9713
639 bool "WM9713 Touchscreen interface support"
640 depends on TOUCHSCREEN_WM97XX
643 Say Y here to enable support for the Wolfson Microelectronics
644 WM9713 touchscreen controller.
646 config TOUCHSCREEN_WM97XX_ATMEL
647 tristate "WM97xx Atmel accelerated touch"
648 depends on TOUCHSCREEN_WM97XX && AVR32
650 Say Y here for support for streaming mode with WM97xx touchscreens
651 on Atmel AT91 or AVR32 systems with an AC97C module.
653 Be aware that this will use channel B in the controller for
654 streaming data, this must not conflict with other AC97C drivers.
658 To compile this driver as a module, choose M here: the module will
659 be called atmel-wm97xx.
661 config TOUCHSCREEN_WM97XX_MAINSTONE
662 tristate "WM97xx Mainstone/Palm accelerated touch"
663 depends on TOUCHSCREEN_WM97XX && ARCH_PXA
665 Say Y here for support for streaming mode with WM97xx touchscreens
666 on Mainstone, Palm Tungsten T5, TX and LifeDrive systems.
670 To compile this driver as a module, choose M here: the
671 module will be called mainstone-wm97xx.
673 config TOUCHSCREEN_WM97XX_ZYLONITE
674 tristate "Zylonite accelerated touch"
675 depends on TOUCHSCREEN_WM97XX && MACH_ZYLONITE
676 select TOUCHSCREEN_WM9713
678 Say Y here for support for streaming mode with the touchscreen
683 To compile this driver as a module, choose M here: the
684 module will be called zylonite-wm97xx.
686 config TOUCHSCREEN_USB_COMPOSITE
687 tristate "USB Touchscreen Driver"
688 depends on USB_ARCH_HAS_HCD
691 USB Touchscreen driver for:
692 - eGalax Touchkit USB (also includes eTurboTouch CT-410/510/700)
693 - PanJit TouchSet USB
694 - 3M MicroTouch USB (EX II series)
696 - some other eTurboTouch
699 - IRTOUCHSYSTEMS/UNITOP
701 - GoTop Super_Q2/GogoPen/PenPower tablets
702 - JASTEC USB Touch Controller/DigiTech DTR-02U
703 - Zytronic controllers
704 - Elo TouchSystems 2700 IntelliTouch
705 - EasyTouch USB Touch Controller from Data Modul
706 - e2i (Mimo monitors)
708 Have a look at <http://linux.chapter7.ch/touchkit/> for
709 a usage description and the required user-space stuff.
711 To compile this driver as a module, choose M here: the
712 module will be called usbtouchscreen.
714 config TOUCHSCREEN_MC13783
715 tristate "Freescale MC13783 touchscreen input driver"
716 depends on MFD_MC13XXX
718 Say Y here if you have an Freescale MC13783 PMIC on your
719 board and want to use its touchscreen
723 To compile this driver as a module, choose M here: the
724 module will be called mc13783_ts.
726 config TOUCHSCREEN_USB_EGALAX
728 bool "eGalax, eTurboTouch CT-410/510/700 device support" if EXPERT
729 depends on TOUCHSCREEN_USB_COMPOSITE
731 config TOUCHSCREEN_USB_PANJIT
733 bool "PanJit device support" if EXPERT
734 depends on TOUCHSCREEN_USB_COMPOSITE
736 config TOUCHSCREEN_USB_3M
738 bool "3M/Microtouch EX II series device support" if EXPERT
739 depends on TOUCHSCREEN_USB_COMPOSITE
741 config TOUCHSCREEN_USB_ITM
743 bool "ITM device support" if EXPERT
744 depends on TOUCHSCREEN_USB_COMPOSITE
746 config TOUCHSCREEN_USB_ETURBO
748 bool "eTurboTouch (non-eGalax compatible) device support" if EXPERT
749 depends on TOUCHSCREEN_USB_COMPOSITE
751 config TOUCHSCREEN_USB_GUNZE
753 bool "Gunze AHL61 device support" if EXPERT
754 depends on TOUCHSCREEN_USB_COMPOSITE
756 config TOUCHSCREEN_USB_DMC_TSC10
758 bool "DMC TSC-10/25 device support" if EXPERT
759 depends on TOUCHSCREEN_USB_COMPOSITE
761 config TOUCHSCREEN_USB_IRTOUCH
763 bool "IRTOUCHSYSTEMS/UNITOP device support" if EXPERT
764 depends on TOUCHSCREEN_USB_COMPOSITE
766 config TOUCHSCREEN_USB_IDEALTEK
768 bool "IdealTEK URTC1000 device support" if EXPERT
769 depends on TOUCHSCREEN_USB_COMPOSITE
771 config TOUCHSCREEN_USB_GENERAL_TOUCH
773 bool "GeneralTouch Touchscreen device support" if EXPERT
774 depends on TOUCHSCREEN_USB_COMPOSITE
776 config TOUCHSCREEN_USB_GOTOP
778 bool "GoTop Super_Q2/GogoPen/PenPower tablet device support" if EXPERT
779 depends on TOUCHSCREEN_USB_COMPOSITE
781 config TOUCHSCREEN_USB_JASTEC
783 bool "JASTEC/DigiTech DTR-02U USB touch controller device support" if EXPERT
784 depends on TOUCHSCREEN_USB_COMPOSITE
786 config TOUCHSCREEN_USB_ELO
788 bool "Elo TouchSystems 2700 IntelliTouch controller device support" if EXPERT
789 depends on TOUCHSCREEN_USB_COMPOSITE
791 config TOUCHSCREEN_USB_E2I
793 bool "e2i Touchscreen controller (e.g. from Mimo 740)" if EXPERT
794 depends on TOUCHSCREEN_USB_COMPOSITE
796 config TOUCHSCREEN_USB_ZYTRONIC
798 bool "Zytronic controller" if EXPERT
799 depends on TOUCHSCREEN_USB_COMPOSITE
801 config TOUCHSCREEN_USB_ETT_TC45USB
803 bool "ET&T USB series TC4UM/TC5UH touchscreen controller support" if EXPERT
804 depends on TOUCHSCREEN_USB_COMPOSITE
806 config TOUCHSCREEN_USB_NEXIO
808 bool "NEXIO/iNexio device support" if EXPERT
809 depends on TOUCHSCREEN_USB_COMPOSITE
811 config TOUCHSCREEN_USB_EASYTOUCH
813 bool "EasyTouch USB Touch controller device support" if EMBEDDED
814 depends on TOUCHSCREEN_USB_COMPOSITE
816 Say Y here if you have an EasyTouch USB Touch controller.
819 config TOUCHSCREEN_TOUCHIT213
820 tristate "Sahara TouchIT-213 touchscreen"
823 Say Y here if you have a Sahara TouchIT-213 Tablet PC.
827 To compile this driver as a module, choose M here: the
828 module will be called touchit213.
830 config TOUCHSCREEN_TSC_SERIO
831 tristate "TSC-10/25/40 serial touchscreen support"
834 Say Y here if you have a TSC-10, 25 or 40 serial touchscreen connected
839 To compile this driver as a module, choose M here: the
840 module will be called tsc40.
842 config TOUCHSCREEN_TSC2005
843 tristate "TSC2005 based touchscreens"
844 depends on SPI_MASTER
846 Say Y here if you have a TSC2005 based touchscreen.
850 To compile this driver as a module, choose M here: the
851 module will be called tsc2005.
853 config TOUCHSCREEN_TSC2007
854 tristate "TSC2007 based touchscreens"
857 Say Y here if you have a TSC2007 based touchscreen.
861 To compile this driver as a module, choose M here: the
862 module will be called tsc2007.
864 config TOUCHSCREEN_W90X900
865 tristate "W90P910 touchscreen driver"
866 depends on ARCH_W90X900
868 Say Y here if you have a W90P910 based touchscreen.
870 To compile this driver as a module, choose M here: the
871 module will be called w90p910_ts.
873 config TOUCHSCREEN_PCAP
874 tristate "Motorola PCAP touchscreen"
877 Say Y here if you have a Motorola EZX telephone and
878 want to enable support for the built-in touchscreen.
880 To compile this driver as a module, choose M here: the
881 module will be called pcap_ts.
883 config TOUCHSCREEN_ST1232
884 tristate "Sitronix ST1232 touchscreen controllers"
887 Say Y here if you want to support Sitronix ST1232
888 touchscreen controller.
892 To compile this driver as a module, choose M here: the
893 module will be called st1232_ts.
895 config TOUCHSCREEN_STMPE
896 tristate "STMicroelectronics STMPE touchscreens"
899 Say Y here if you want support for STMicroelectronics
900 STMPE touchscreen controllers.
902 To compile this driver as a module, choose M here: the
903 module will be called stmpe-ts.
905 config TOUCHSCREEN_SUN4I
906 tristate "Allwinner sun4i resistive touchscreen controller support"
907 depends on ARCH_SUNXI || COMPILE_TEST
910 This selects support for the resistive touchscreen controller
911 found on Allwinner sunxi SoCs.
913 To compile this driver as a module, choose M here: the
914 module will be called sun4i-ts.
916 config TOUCHSCREEN_SUR40
917 tristate "Samsung SUR40 (Surface 2.0/PixelSense) touchscreen"
921 Say Y here if you want support for the Samsung SUR40 touchscreen
922 (also known as Microsoft Surface 2.0 or Microsoft PixelSense).
924 To compile this driver as a module, choose M here: the
925 module will be called sur40.
927 config TOUCHSCREEN_TPS6507X
928 tristate "TPS6507x based touchscreens"
932 Say Y here if you have a TPS6507x based touchscreen
937 To compile this driver as a module, choose M here: the
938 module will be called tps6507x_ts.
940 config TOUCHSCREEN_ZFORCE
941 tristate "Neonode zForce infrared touchscreens"
945 Say Y here if you have a touchscreen using the zforce
946 infraread technology from Neonode.
950 To compile this driver as a module, choose M here: the
951 module will be called zforce_ts.