]> git.proxmox.com Git - mirror_ubuntu-jammy-kernel.git/blob - drivers/irqchip/alphascale_asm9260-icoll.h
Merge tag 'for-linus-5.3' of git://github.com/cminyard/linux-ipmi
[mirror_ubuntu-jammy-kernel.git] / drivers / irqchip / alphascale_asm9260-icoll.h
1 /* SPDX-License-Identifier: GPL-2.0-or-later */
2 /*
3 * Copyright (C) 2014 Oleksij Rempel <linux@rempel-privat.de>
4 */
5
6 #ifndef _ALPHASCALE_ASM9260_ICOLL_H
7 #define _ALPHASCALE_ASM9260_ICOLL_H
8
9 #define ASM9260_NUM_IRQS 64
10 /*
11 * this device provide 4 offsets for each register:
12 * 0x0 - plain read write mode
13 * 0x4 - set mode, OR logic.
14 * 0x8 - clr mode, XOR logic.
15 * 0xc - togle mode.
16 */
17
18 #define ASM9260_HW_ICOLL_VECTOR 0x0000
19 /*
20 * bits 31:2
21 * This register presents the vector address for the interrupt currently
22 * active on the CPU IRQ input. Writing to this register notifies the
23 * interrupt collector that the interrupt service routine for the current
24 * interrupt has been entered.
25 * The exception trap should have a LDPC instruction from this address:
26 * LDPC ASM9260_HW_ICOLL_VECTOR_ADDR; IRQ exception at 0xffff0018
27 */
28
29 /*
30 * The Interrupt Collector Level Acknowledge Register is used by software to
31 * indicate the completion of an interrupt on a specific level.
32 * This register is written at the very end of an interrupt service routine. If
33 * nesting is used then the CPU irq must be turned on before writing to this
34 * register to avoid a race condition in the CPU interrupt hardware.
35 */
36 #define ASM9260_HW_ICOLL_LEVELACK 0x0010
37 #define ASM9260_BM_LEVELn(nr) BIT(nr)
38
39 #define ASM9260_HW_ICOLL_CTRL 0x0020
40 /*
41 * ASM9260_BM_CTRL_SFTRST and ASM9260_BM_CTRL_CLKGATE are not available on
42 * asm9260.
43 */
44 #define ASM9260_BM_CTRL_SFTRST BIT(31)
45 #define ASM9260_BM_CTRL_CLKGATE BIT(30)
46 /* disable interrupt level nesting */
47 #define ASM9260_BM_CTRL_NO_NESTING BIT(19)
48 /*
49 * Set this bit to one enable the RISC32-style read side effect associated with
50 * the vector address register. In this mode, interrupt in-service is signaled
51 * by the read of the ASM9260_HW_ICOLL_VECTOR register to acquire the interrupt
52 * vector address. Set this bit to zero for normal operation, in which the ISR
53 * signals in-service explicitly by means of a write to the
54 * ASM9260_HW_ICOLL_VECTOR register.
55 * 0 - Must Write to Vector register to go in-service.
56 * 1 - Go in-service as a read side effect
57 */
58 #define ASM9260_BM_CTRL_ARM_RSE_MODE BIT(18)
59 #define ASM9260_BM_CTRL_IRQ_ENABLE BIT(16)
60
61 #define ASM9260_HW_ICOLL_STAT_OFFSET 0x0030
62 /*
63 * bits 5:0
64 * Vector number of current interrupt. Multiply by 4 and add to vector base
65 * address to obtain the value in ASM9260_HW_ICOLL_VECTOR.
66 */
67
68 /*
69 * RAW0 and RAW1 provides a read-only view of the raw interrupt request lines
70 * coming from various parts of the chip. Its purpose is to improve diagnostic
71 * observability.
72 */
73 #define ASM9260_HW_ICOLL_RAW0 0x0040
74 #define ASM9260_HW_ICOLL_RAW1 0x0050
75
76 #define ASM9260_HW_ICOLL_INTERRUPT0 0x0060
77 #define ASM9260_HW_ICOLL_INTERRUPTn(n) (0x0060 + ((n) >> 2) * 0x10)
78 /*
79 * WARNING: Modifying the priority of an enabled interrupt may result in
80 * undefined behavior.
81 */
82 #define ASM9260_BM_INT_PRIORITY_MASK 0x3
83 #define ASM9260_BM_INT_ENABLE BIT(2)
84 #define ASM9260_BM_INT_SOFTIRQ BIT(3)
85
86 #define ASM9260_BM_ICOLL_INTERRUPTn_SHIFT(n) (((n) & 0x3) << 3)
87 #define ASM9260_BM_ICOLL_INTERRUPTn_ENABLE(n) (1 << (2 + \
88 ASM9260_BM_ICOLL_INTERRUPTn_SHIFT(n)))
89
90 #define ASM9260_HW_ICOLL_VBASE 0x0160
91 /*
92 * bits 31:2
93 * This bitfield holds the upper 30 bits of the base address of the vector
94 * table.
95 */
96
97 #define ASM9260_HW_ICOLL_CLEAR0 0x01d0
98 #define ASM9260_HW_ICOLL_CLEAR1 0x01e0
99 #define ASM9260_HW_ICOLL_CLEARn(n) (((n >> 5) * 0x10) \
100 + SET_REG)
101 #define ASM9260_BM_CLEAR_BIT(n) BIT(n & 0x1f)
102
103 /* Scratchpad */
104 #define ASM9260_HW_ICOLL_UNDEF_VECTOR 0x01f0
105 #endif