drivers/leds/Kconfig

   1 config LEDS_GPIO_REGISTER
   2         bool
   3         help
   4           This option provides the function gpio_led_register_device.
   5           As this function is used by arch code it must not be compiled as a
   6           module.
   7
   8 menuconfig NEW_LEDS
   9         bool "LED Support"
  10         help
  11           Say Y to enable Linux LED support.  This allows control of supported
  12           LEDs from both userspace and optionally, by kernel events (triggers).
  13
  14 if NEW_LEDS
  15
  16 config LEDS_CLASS
  17         tristate "LED Class Support"
  18         help
  19           This option enables the led sysfs class in /sys/class/leds.  You'll
  20           need this to do anything useful with LEDs.  If unsure, say N.
  21
  22 config LEDS_CLASS_FLASH
  23         tristate "LED Flash Class Support"
  24         depends on LEDS_CLASS
  25         help
  26           This option enables the flash led sysfs class in /sys/class/leds.
  27           It wrapps LED Class and adds flash LEDs specific sysfs attributes
  28           and kernel internal API to it. You'll need this to provide support
  29           for the flash related features of a LED device. It can be built
  30           as a module.
  31
  32 config LEDS_BRIGHTNESS_HW_CHANGED
  33         bool "LED Class brightness_hw_changed attribute support"
  34         depends on LEDS_CLASS
  35         help
  36           This option enables support for the brightness_hw_changed attribute
  37           for led sysfs class devices under /sys/class/leds.
  38
  39           See Documentation/ABI/testing/sysfs-class-led for details.
  40
  41 comment "LED drivers"
  42
  43 config LEDS_88PM860X
  44         tristate "LED Support for Marvell 88PM860x PMIC"
  45         depends on LEDS_CLASS
  46         depends on MFD_88PM860X
  47         help
  48           This option enables support for on-chip LED drivers found on Marvell
  49           Semiconductor 88PM8606 PMIC.
  50
  51 config LEDS_AAT1290
  52         tristate "LED support for the AAT1290"
  53         depends on LEDS_CLASS_FLASH
  54         depends on V4L2_FLASH_LED_CLASS || !V4L2_FLASH_LED_CLASS
  55         depends on GPIOLIB || COMPILE_TEST
  56         depends on OF
  57         depends on PINCTRL
  58         help
  59          This option enables support for the LEDs on the AAT1290.
  60
  61 config LEDS_BCM6328
  62         tristate "LED Support for Broadcom BCM6328"
  63         depends on LEDS_CLASS
  64         depends on HAS_IOMEM
  65         depends on OF
  66         help
  67           This option enables support for LEDs connected to the BCM6328
  68           LED HW controller accessed via MMIO registers.
  69
  70 config LEDS_BCM6358
  71         tristate "LED Support for Broadcom BCM6358"
  72         depends on LEDS_CLASS
  73         depends on HAS_IOMEM
  74         depends on OF
  75         help
  76           This option enables support for LEDs connected to the BCM6358
  77           LED HW controller accessed via MMIO registers.
  78
  79 config LEDS_CPCAP
  80         tristate "LED Support for Motorola CPCAP"
  81         depends on LEDS_CLASS
  82         depends on MFD_CPCAP
  83         depends on OF
  84         help
  85           This option enables support for LEDs offered by Motorola's
  86           CPCAP PMIC.
  87
  88 config LEDS_LM3530
  89         tristate "LCD Backlight driver for LM3530"
  90         depends on LEDS_CLASS
  91         depends on I2C
  92         help
  93           This option enables support for the LCD backlight using
  94           LM3530 ambient light sensor chip. This ALS chip can be
  95           controlled manually or using PWM input or using ambient
  96           light automatically.
  97
  98 config LEDS_LM3533
  99         tristate "LED support for LM3533"
 100         depends on LEDS_CLASS
 101         depends on MFD_LM3533
 102         help
 103           This option enables support for the LEDs on National Semiconductor /
 104           TI LM3533 Lighting Power chips.
 105
 106           The LEDs can be controlled directly, through PWM input, or by the
 107           ambient-light-sensor interface. The chip supports
 108           hardware-accelerated blinking with maximum on and off periods of 9.8
 109           and 77 seconds respectively.
 110
 111 config LEDS_LM3642
 112         tristate "LED support for LM3642 Chip"
 113         depends on LEDS_CLASS && I2C
 114         select REGMAP_I2C
 115         help
 116           This option enables support for LEDs connected to LM3642.
 117           The LM3642 is a 4MHz fixed-frequency synchronous boost
 118           converter plus 1.5A constant current driver for a high-current
 119           white LED.
 120
 121
 122 config LEDS_LOCOMO
 123         tristate "LED Support for Locomo device"
 124         depends on LEDS_CLASS
 125         depends on SHARP_LOCOMO
 126         help
 127           This option enables support for the LEDs on Sharp Locomo.
 128           Zaurus models SL-5500 and SL-5600.
 129
 130 config LEDS_MIKROTIK_RB532
 131         tristate "LED Support for Mikrotik Routerboard 532"
 132         depends on LEDS_CLASS
 133         depends on MIKROTIK_RB532
 134         help
 135           This option enables support for the so called "User LED" of
 136           Mikrotik's Routerboard 532.
 137
 138 config LEDS_MT6323
 139         tristate "LED Support for Mediatek MT6323 PMIC"
 140         depends on LEDS_CLASS
 141         depends on MFD_MT6397
 142         help
 143           This option enables support for on-chip LED drivers found on
 144           Mediatek MT6323 PMIC.
 145
 146 config LEDS_S3C24XX
 147         tristate "LED Support for Samsung S3C24XX GPIO LEDs"
 148         depends on LEDS_CLASS
 149         depends on ARCH_S3C24XX
 150         help
 151           This option enables support for LEDs connected to GPIO lines
 152           on Samsung S3C24XX series CPUs, such as the S3C2410 and S3C2440.
 153
 154 config LEDS_NET48XX
 155         tristate "LED Support for Soekris net48xx series Error LED"
 156         depends on LEDS_CLASS
 157         depends on SCx200_GPIO
 158         help
 159           This option enables support for the Soekris net4801 and net4826 error
 160           LED.
 161
 162 config LEDS_FSG
 163         tristate "LED Support for the Freecom FSG-3"
 164         depends on LEDS_CLASS
 165         depends on MACH_FSG
 166         help
 167           This option enables support for the LEDs on the Freecom FSG-3.
 168
 169 config LEDS_WRAP
 170         tristate "LED Support for the WRAP series LEDs"
 171         depends on LEDS_CLASS
 172         depends on SCx200_GPIO
 173         help
 174           This option enables support for the PCEngines WRAP programmable LEDs.
 175
 176 config LEDS_COBALT_QUBE
 177         tristate "LED Support for the Cobalt Qube series front LED"
 178         depends on LEDS_CLASS
 179         depends on MIPS_COBALT
 180         help
 181           This option enables support for the front LED on Cobalt Qube series
 182
 183 config LEDS_COBALT_RAQ
 184         bool "LED Support for the Cobalt Raq series"
 185         depends on LEDS_CLASS=y && MIPS_COBALT
 186         select LEDS_TRIGGERS
 187         help
 188           This option enables support for the Cobalt Raq series LEDs.
 189
 190 config LEDS_SUNFIRE
 191         tristate "LED support for SunFire servers."
 192         depends on LEDS_CLASS
 193         depends on SPARC64
 194         select LEDS_TRIGGERS
 195         help
 196           This option enables support for the Left, Middle, and Right
 197           LEDs on the I/O and CPU boards of SunFire UltraSPARC servers.
 198
 199 config LEDS_IPAQ_MICRO
 200         tristate "LED Support for the Compaq iPAQ h3xxx"
 201         depends on LEDS_CLASS
 202         depends on MFD_IPAQ_MICRO
 203         help
 204           Choose this option if you want to use the notification LED on
 205           Compaq/HP iPAQ h3100 and h3600.
 206
 207 config LEDS_HP6XX
 208         tristate "LED Support for the HP Jornada 6xx"
 209         depends on LEDS_CLASS
 210         depends on SH_HP6XX
 211         help
 212           This option enables LED support for the handheld
 213           HP Jornada 620/660/680/690.
 214
 215 config LEDS_PCA9532
 216         tristate "LED driver for PCA9532 dimmer"
 217         depends on LEDS_CLASS
 218         depends on I2C && INPUT
 219         help
 220           This option enables support for NXP pca9532
 221           LED controller. It is generally only useful
 222           as a platform driver
 223
 224 config LEDS_PCA9532_GPIO
 225         bool "Enable GPIO support for PCA9532"
 226         depends on LEDS_PCA9532
 227         depends on GPIOLIB
 228         help
 229           Allow unused pins on PCA9532 to be used as gpio.
 230
 231           To use a pin as gpio pca9532_type in pca9532_platform data needs to
 232           set to PCA9532_TYPE_GPIO.
 233
 234 config LEDS_GPIO
 235         tristate "LED Support for GPIO connected LEDs"
 236         depends on LEDS_CLASS
 237         depends on GPIOLIB || COMPILE_TEST
 238         help
 239           This option enables support for the LEDs connected to GPIO
 240           outputs. To be useful the particular board must have LEDs
 241           and they must be connected to the GPIO lines.  The LEDs must be
 242           defined as platform devices and/or OpenFirmware platform devices.
 243           The code to use these bindings can be selected below.
 244
 245 config LEDS_LP3944
 246         tristate "LED Support for N.S. LP3944 (Fun Light) I2C chip"
 247         depends on LEDS_CLASS
 248         depends on I2C
 249         help
 250           This option enables support for LEDs connected to the National
 251           Semiconductor LP3944 Lighting Management Unit (LMU) also known as
 252           Fun Light Chip.
 253
 254           To compile this driver as a module, choose M here: the
 255           module will be called leds-lp3944.
 256
 257 config LEDS_LP3952
 258         tristate "LED Support for TI LP3952 2 channel LED driver"
 259         depends on LEDS_CLASS
 260         depends on I2C
 261         depends on GPIOLIB
 262         select REGMAP_I2C
 263         help
 264           This option enables support for LEDs connected to the Texas
 265           Instruments LP3952 LED driver.
 266
 267           To compile this driver as a module, choose M here: the
 268           module will be called leds-lp3952.
 269
 270 config LEDS_LP55XX_COMMON
 271         tristate "Common Driver for TI/National LP5521/5523/55231/5562/8501"
 272         depends on LEDS_LP5521 || LEDS_LP5523 || LEDS_LP5562 || LEDS_LP8501
 273         select FW_LOADER
 274         select FW_LOADER_USER_HELPER
 275         help
 276           This option supports common operations for LP5521/5523/55231/5562/8501
 277           devices.
 278
 279 config LEDS_LP5521
 280         tristate "LED Support for N.S. LP5521 LED driver chip"
 281         depends on LEDS_CLASS && I2C
 282         select LEDS_LP55XX_COMMON
 283         help
 284           If you say yes here you get support for the National Semiconductor
 285           LP5521 LED driver. It is 3 channel chip with programmable engines.
 286           Driver provides direct control via LED class and interface for
 287           programming the engines.
 288
 289 config LEDS_LP5523
 290         tristate "LED Support for TI/National LP5523/55231 LED driver chip"
 291         depends on LEDS_CLASS && I2C
 292         select LEDS_LP55XX_COMMON
 293         help
 294           If you say yes here you get support for TI/National Semiconductor
 295           LP5523/55231 LED driver.
 296           It is 9 channel chip with programmable engines.
 297           Driver provides direct control via LED class and interface for
 298           programming the engines.
 299
 300 config LEDS_LP5562
 301         tristate "LED Support for TI LP5562 LED driver chip"
 302         depends on LEDS_CLASS && I2C
 303         select LEDS_LP55XX_COMMON
 304         help
 305           If you say yes here you get support for TI LP5562 LED driver.
 306           It is 4 channels chip with programmable engines.
 307           Driver provides direct control via LED class and interface for
 308           programming the engines.
 309
 310 config LEDS_LP8501
 311         tristate "LED Support for TI LP8501 LED driver chip"
 312         depends on LEDS_CLASS && I2C
 313         select LEDS_LP55XX_COMMON
 314         help
 315           If you say yes here you get support for TI LP8501 LED driver.
 316           It is 9 channel chip with programmable engines.
 317           Driver provides direct control via LED class and interface for
 318           programming the engines.
 319           It is similar as LP5523, but output power selection is available.
 320           And register layout and engine program schemes are different.
 321
 322 config LEDS_LP8788
 323         tristate "LED support for the TI LP8788 PMIC"
 324         depends on LEDS_CLASS
 325         depends on MFD_LP8788
 326         help
 327           This option enables support for the Keyboard LEDs on the LP8788 PMIC.
 328
 329 config LEDS_LP8860
 330         tristate "LED support for the TI LP8860 4 channel LED driver"
 331         depends on LEDS_CLASS && I2C
 332         select REGMAP_I2C
 333         help
 334           If you say yes here you get support for the TI LP8860 4 channel
 335           LED driver.
 336           This option enables support for the display cluster LEDs
 337           on the LP8860 4 channel LED driver using the I2C communication
 338           bus.
 339
 340 config LEDS_CLEVO_MAIL
 341         tristate "Mail LED on Clevo notebook"
 342         depends on LEDS_CLASS
 343         depends on X86 && SERIO_I8042 && DMI
 344         help
 345           This driver makes the mail LED accessible from userspace
 346           programs through the leds subsystem. This LED have three
 347           known mode: off, blink at 0.5Hz and blink at 1Hz.
 348
 349           The driver supports two kinds of interface: using ledtrig-timer
 350           or through /sys/class/leds/clevo::mail/brightness. As this LED
 351           cannot change it's brightness it blinks instead. The brightness
 352           value 0 means off, 1..127 means blink at 0.5Hz and 128..255 means
 353           blink at 1Hz.
 354
 355           This module can drive the mail LED for the following notebooks:
 356
 357                 Clevo D400P
 358                 Clevo D410J
 359                 Clevo D410V
 360                 Clevo D400V/D470V (not tested, but might work)
 361                 Clevo M540N
 362                 Clevo M5x0N (not tested, but might work)
 363                 Positivo Mobile (Clevo M5x0V)
 364
 365           If your model is not listed here you can try the "nodetect"
 366           module parameter.
 367
 368           To compile this driver as a module, choose M here: the
 369           module will be called leds-clevo-mail.
 370
 371 config LEDS_PCA955X
 372         tristate "LED Support for PCA955x I2C chips"
 373         depends on LEDS_CLASS
 374         depends on I2C
 375         help
 376           This option enables support for LEDs connected to PCA955x
 377           LED driver chips accessed via the I2C bus.  Supported
 378           devices include PCA9550, PCA9551, PCA9552, and PCA9553.
 379
 380 config LEDS_PCA963X
 381         tristate "LED support for PCA963x I2C chip"
 382         depends on LEDS_CLASS
 383         depends on I2C
 384         help
 385           This option enables support for LEDs connected to the PCA963x
 386           LED driver chip accessed via the I2C bus. Supported
 387           devices include PCA9633 and PCA9634
 388
 389 config LEDS_WM831X_STATUS
 390         tristate "LED support for status LEDs on WM831x PMICs"
 391         depends on LEDS_CLASS
 392         depends on MFD_WM831X
 393         help
 394           This option enables support for the status LEDs of the WM831x
 395           series of PMICs.
 396
 397 config LEDS_WM8350
 398         tristate "LED Support for WM8350 AudioPlus PMIC"
 399         depends on LEDS_CLASS
 400         depends on MFD_WM8350
 401         help
 402           This option enables support for LEDs driven by the Wolfson
 403           Microelectronics WM8350 AudioPlus PMIC.
 404
 405 config LEDS_DA903X
 406         tristate "LED Support for DA9030/DA9034 PMIC"
 407         depends on LEDS_CLASS
 408         depends on PMIC_DA903X
 409         help
 410           This option enables support for on-chip LED drivers found
 411           on Dialog Semiconductor DA9030/DA9034 PMICs.
 412
 413 config LEDS_DA9052
 414         tristate "Dialog DA9052/DA9053 LEDS"
 415         depends on LEDS_CLASS
 416         depends on PMIC_DA9052
 417         help
 418           This option enables support for on-chip LED drivers found
 419           on Dialog Semiconductor DA9052-BC and DA9053-AA/Bx PMICs.
 420
 421 config LEDS_DAC124S085
 422         tristate "LED Support for DAC124S085 SPI DAC"
 423         depends on LEDS_CLASS
 424         depends on SPI
 425         help
 426           This option enables support for DAC124S085 SPI DAC from NatSemi,
 427           which can be used to control up to four LEDs.
 428
 429 config LEDS_PWM
 430         tristate "PWM driven LED Support"
 431         depends on LEDS_CLASS
 432         depends on PWM
 433         help
 434           This option enables support for pwm driven LEDs
 435
 436 config LEDS_REGULATOR
 437         tristate "REGULATOR driven LED support"
 438         depends on LEDS_CLASS
 439         depends on REGULATOR
 440         help
 441           This option enables support for regulator driven LEDs.
 442
 443 config LEDS_BD2802
 444         tristate "LED driver for BD2802 RGB LED"
 445         depends on LEDS_CLASS
 446         depends on I2C
 447         help
 448           This option enables support for BD2802GU RGB LED driver chips
 449           accessed via the I2C bus.
 450
 451 config LEDS_INTEL_SS4200
 452         tristate "LED driver for Intel NAS SS4200 series"
 453         depends on LEDS_CLASS
 454         depends on PCI && DMI
 455         depends on X86
 456         help
 457           This option enables support for the Intel SS4200 series of
 458           Network Attached Storage servers. You may control the hard
 459           drive or power LEDs on the front panel. Using this driver
 460           can stop the front LED from blinking after startup.
 461
 462 config LEDS_LT3593
 463         tristate "LED driver for LT3593 controllers"
 464         depends on LEDS_CLASS
 465         depends on GPIOLIB || COMPILE_TEST
 466         help
 467           This option enables support for LEDs driven by a Linear Technology
 468           LT3593 controller. This controller uses a special one-wire pulse
 469           coding protocol to set the brightness.
 470
 471 config LEDS_ADP5520
 472         tristate "LED Support for ADP5520/ADP5501 PMIC"
 473         depends on LEDS_CLASS
 474         depends on PMIC_ADP5520
 475         help
 476           This option enables support for on-chip LED drivers found
 477           on Analog Devices ADP5520/ADP5501 PMICs.
 478
 479           To compile this driver as a module, choose M here: the module will
 480           be called leds-adp5520.
 481
 482 config LEDS_MC13783
 483         tristate "LED Support for MC13XXX PMIC"
 484         depends on LEDS_CLASS
 485         depends on MFD_MC13XXX
 486         help
 487           This option enable support for on-chip LED drivers found
 488           on Freescale Semiconductor MC13783/MC13892/MC34708 PMIC.
 489
 490 config LEDS_NS2
 491         tristate "LED support for Network Space v2 GPIO LEDs"
 492         depends on LEDS_CLASS
 493         depends on MACH_KIRKWOOD || MACH_ARMADA_370
 494         default y
 495         help
 496           This option enables support for the dual-GPIO LEDs found on the
 497           following LaCie/Seagate boards:
 498
 499                 Network Space v2 (and parents: Max, Mini)
 500                 Internet Space v2
 501                 d2 Network v2
 502                 n090401 (Seagate NAS 4-Bay)
 503
 504 config LEDS_NETXBIG
 505         tristate "LED support for Big Network series LEDs"
 506         depends on LEDS_CLASS
 507         depends on MACH_KIRKWOOD
 508         default y
 509         help
 510           This option enable support for LEDs found on the LaCie 2Big
 511           and 5Big Network v2 boards. The LEDs are wired to a CPLD and are
 512           controlled through a GPIO extension bus.
 513
 514 config LEDS_ASIC3
 515         bool "LED support for the HTC ASIC3"
 516         depends on LEDS_CLASS=y
 517         depends on MFD_ASIC3
 518         default y
 519         help
 520           This option enables support for the LEDs on the HTC ASIC3. The HTC
 521           ASIC3 LED GPIOs are inputs, not outputs, thus the leds-gpio driver
 522           cannot be used. This driver supports hardware blinking with an on+off
 523           period from 62ms to 125s. Say Y to enable LEDs on the HP iPAQ hx4700.
 524
 525 config LEDS_TCA6507
 526         tristate "LED Support for TCA6507 I2C chip"
 527         depends on LEDS_CLASS && I2C
 528         help
 529           This option enables support for LEDs connected to TC6507
 530           LED driver chips accessed via the I2C bus.
 531           Driver support brightness control and hardware-assisted blinking.
 532
 533 config LEDS_TLC591XX
 534         tristate "LED driver for TLC59108 and TLC59116 controllers"
 535         depends on LEDS_CLASS && I2C
 536         select REGMAP_I2C
 537         help
 538           This option enables support for Texas Instruments TLC59108
 539           and TLC59116 LED controllers.
 540
 541 config LEDS_MAX77693
 542         tristate "LED support for MAX77693 Flash"
 543         depends on LEDS_CLASS_FLASH
 544         depends on V4L2_FLASH_LED_CLASS || !V4L2_FLASH_LED_CLASS
 545         depends on MFD_MAX77693
 546         depends on OF
 547         help
 548           This option enables support for the flash part of the MAX77693
 549           multifunction device. It has build in control for two leds in flash
 550           and torch mode.
 551
 552 config LEDS_MAX8997
 553         tristate "LED support for MAX8997 PMIC"
 554         depends on LEDS_CLASS && MFD_MAX8997
 555         help
 556           This option enables support for on-chip LED drivers on
 557           MAXIM MAX8997 PMIC.
 558
 559 config LEDS_LM355x
 560         tristate "LED support for LM355x Chips, LM3554 and LM3556"
 561         depends on LEDS_CLASS && I2C
 562         select REGMAP_I2C
 563         help
 564           This option enables support for LEDs connected to LM355x.
 565           LM355x includes Torch, Flash and Indicator functions.
 566
 567 config LEDS_OT200
 568         tristate "LED support for the Bachmann OT200"
 569         depends on LEDS_CLASS && HAS_IOMEM && (X86_32 || COMPILE_TEST)
 570         help
 571           This option enables support for the LEDs on the Bachmann OT200.
 572           Say Y to enable LEDs on the Bachmann OT200.
 573
 574 config LEDS_MENF21BMC
 575         tristate "LED support for the MEN 14F021P00 BMC"
 576         depends on LEDS_CLASS && MFD_MENF21BMC
 577         help
 578           Say Y here to include support for the MEN 14F021P00 BMC LEDs.
 579
 580           This driver can also be built as a module. If so the module
 581           will be called leds-menf21bmc.
 582
 583 config LEDS_KTD2692
 584         tristate "LED support for KTD2692 flash LED controller"
 585         depends on LEDS_CLASS_FLASH && OF
 586         depends on GPIOLIB || COMPILE_TEST
 587         help
 588           This option enables support for KTD2692 LED flash connected
 589           through ExpressWire interface.
 590
 591           Say Y to enable this driver.
 592
 593 config LEDS_IS31FL319X
 594         tristate "LED Support for ISSI IS31FL319x I2C LED controller family"
 595         depends on LEDS_CLASS && I2C && OF
 596         select REGMAP_I2C
 597         help
 598           This option enables support for LEDs connected to ISSI IS31FL319x
 599           fancy LED driver chips accessed via the I2C bus.
 600           Driver supports individual PWM brightness control for each channel.
 601
 602           This driver can also be built as a module. If so the module will be
 603           called leds-is31fl319x.
 604
 605 config LEDS_IS31FL32XX
 606         tristate "LED support for ISSI IS31FL32XX I2C LED controller family"
 607         depends on LEDS_CLASS && I2C && OF
 608         help
 609           Say Y here to include support for ISSI IS31FL32XX and Si-En SN32xx
 610           LED controllers. They are I2C devices with multiple constant-current
 611           channels, each with independent 256-level PWM control.
 612
 613 comment "LED driver for blink(1) USB RGB LED is under Special HID drivers (HID_THINGM)"
 614
 615 config LEDS_BLINKM
 616         tristate "LED support for the BlinkM I2C RGB LED"
 617         depends on LEDS_CLASS
 618         depends on I2C
 619         help
 620           This option enables support for the BlinkM RGB LED connected
 621           through I2C. Say Y to enable support for the BlinkM LED.
 622
 623 config LEDS_POWERNV
 624         tristate "LED support for PowerNV Platform"
 625         depends on LEDS_CLASS
 626         depends on PPC_POWERNV
 627         depends on OF
 628         help
 629           This option enables support for the system LEDs present on
 630           PowerNV platforms. Say 'y' to enable this support in kernel.
 631           To compile this driver as a module, choose 'm' here: the module
 632           will be called leds-powernv.
 633
 634 config LEDS_SYSCON
 635         bool "LED support for LEDs on system controllers"
 636         depends on LEDS_CLASS=y
 637         depends on MFD_SYSCON
 638         depends on OF
 639         help
 640           This option enabled support for the LEDs on syscon type
 641           devices. This will only work with device tree enabled
 642           devices.
 643
 644 config LEDS_PM8058
 645         tristate "LED Support for the Qualcomm PM8058 PMIC"
 646         depends on MFD_PM8XXX
 647         depends on LEDS_CLASS
 648         help
 649           Choose this option if you want to use the LED drivers in
 650           the Qualcomm PM8058 PMIC.
 651
 652 config LEDS_MLXCPLD
 653         tristate "LED support for the Mellanox boards"
 654         depends on X86_64 && DMI
 655         depends on LEDS_CLASS
 656         help
 657           This option enabled support for the LEDs on the Mellanox
 658           boards. Say Y to enabled these.
 659
 660 config LEDS_USER
 661         tristate "Userspace LED support"
 662         depends on LEDS_CLASS
 663         help
 664           This option enables support for userspace LEDs. Say 'y' to enable this
 665           support in kernel. To compile this driver as a module, choose 'm' here:
 666           the module will be called uleds.
 667
 668 config LEDS_NIC78BX
 669         tristate "LED support for NI PXI NIC78bx devices"
 670         depends on LEDS_CLASS
 671         depends on X86 && ACPI
 672         help
 673           This option enables support for the User1 and User2 LEDs on NI
 674           PXI NIC78bx devices.
 675
 676           To compile this driver as a module, choose M here: the module
 677           will be called leds-nic78bx.
 678
 679 comment "LED Triggers"
 680 source "drivers/leds/trigger/Kconfig"
 681
 682 endif # NEW_LEDS