1 # SPDX-License-Identifier: GPL-2.0-only
4 tristate "Remote Controller support"
7 Enable support for Remote Controllers on Linux. This is
8 needed in order to support several video capture adapters,
9 standalone IR receivers/transmitters, and RF receivers.
11 Enable this option if you have a video capture board even
12 if you don't need IR, as otherwise, you may not be able to
13 compile the driver for your adapter.
15 Say Y when you have a TV or an IR device.
18 source "drivers/media/rc/keymaps/Kconfig"
21 bool "LIRC user interface"
23 Enable this option to enable the Linux Infrared Remote
24 Control user interface (e.g. /dev/lirc*). This interface
25 passes raw IR to and from userspace, which is needed for
26 IR transmitting (aka "blasting") and for the lirc daemon.
29 bool "Support for eBPF programs attached to lirc devices"
30 depends on BPF_SYSCALL
34 Allow attaching eBPF programs to a lirc device using the bpf(2)
35 syscall command BPF_PROG_ATTACH. This is supported for raw IR
38 These eBPF programs can be used to decode IR into scancodes, for
39 IR protocols not supported by the kernel decoders.
41 menuconfig RC_DECODERS
42 bool "Remote controller decoders"
46 tristate "Enable IR raw decoder for the NEC protocol"
50 Enable this option if you have IR with NEC protocol, and
51 if the IR is decoded in software
54 tristate "Enable IR raw decoder for the RC-5 protocol"
58 Enable this option if you have IR with RC-5 protocol, and
59 if the IR is decoded in software
62 tristate "Enable IR raw decoder for the RC6 protocol"
66 Enable this option if you have an infrared remote control which
67 uses the RC6 protocol, and you need software decoding support.
70 tristate "Enable IR raw decoder for the JVC protocol"
74 Enable this option if you have an infrared remote control which
75 uses the JVC protocol, and you need software decoding support.
77 config IR_SONY_DECODER
78 tristate "Enable IR raw decoder for the Sony protocol"
82 Enable this option if you have an infrared remote control which
83 uses the Sony protocol, and you need software decoding support.
85 config IR_SANYO_DECODER
86 tristate "Enable IR raw decoder for the Sanyo protocol"
90 Enable this option if you have an infrared remote control which
91 uses the Sanyo protocol (Sanyo, Aiwa, Chinon remotes),
92 and you need software decoding support.
94 config IR_SHARP_DECODER
95 tristate "Enable IR raw decoder for the Sharp protocol"
99 Enable this option if you have an infrared remote control which
100 uses the Sharp protocol (Sharp, Denon), and you need software
103 config IR_MCE_KBD_DECODER
104 tristate "Enable IR raw decoder for the MCE keyboard/mouse protocol"
108 Enable this option if you have a Microsoft Remote Keyboard for
109 Windows Media Center Edition, which you would like to use with
110 a raw IR receiver in your system.
112 config IR_XMP_DECODER
113 tristate "Enable IR raw decoder for the XMP protocol"
117 Enable this option if you have IR with XMP protocol, and
118 if the IR is decoded in software
120 config IR_IMON_DECODER
121 tristate "Enable IR raw decoder for the iMON protocol"
123 Enable this option if you have iMON PAD or Antec Veris infrared
124 remote control and you would like to use it with a raw IR
125 receiver, or if you wish to use an encoder to transmit this IR.
127 config IR_RCMM_DECODER
128 tristate "Enable IR raw decoder for the RC-MM protocol"
130 Enable this option when you have IR with RC-MM protocol, and
131 you need the software decoder. The driver supports 12,
132 24 and 32 bits RC-MM variants. You can enable or disable the
133 different modes using the following RC protocol keywords:
134 'rc-mm-12', 'rc-mm-24' and 'rc-mm-32'.
136 To compile this driver as a module, choose M here: the module
137 will be called ir-rcmm-decoder.
141 menuconfig RC_DEVICES
142 bool "Remote Controller devices"
147 tristate "ATI / X10 based USB RF remote controls"
150 Say Y here if you want to use an X10 based USB remote control.
151 These are RF remotes with USB receivers.
153 Such devices include the ATI remote that comes with many of ATI's
154 All-In-Wonder video cards, the X10 "Lola" remote, NVIDIA RF remote,
155 Medion RF remote, and SnapStream FireFly remote.
157 This driver provides mouse pointer, left and right mouse buttons,
158 and maps all the other remote buttons to keypress events.
160 To compile this driver as a module, choose M here: the module will be
164 tristate "ENE eHome Receiver/Transceiver (pnp id: ENE0100/ENE02xxx)"
165 depends on PNP || COMPILE_TEST
167 Say Y here to enable support for integrated infrared receiver
168 /transceiver made by ENE.
170 You can see if you have it by looking at lspnp output.
171 Output should include ENE0100 ENE0200 or something similar.
173 To compile this driver as a module, choose M here: the
174 module will be called ene_ir.
177 tristate "Hisilicon hix5hd2 IR remote control"
178 depends on OF || COMPILE_TEST
180 Say Y here if you want to use hisilicon hix5hd2 remote control.
181 To compile this driver as a module, choose M here: the module will be
184 If you're not sure, select N here
187 tristate "SoundGraph iMON Receiver and Display"
190 Say Y here if you want to use a SoundGraph iMON (aka Antec Veris)
191 IR Receiver and/or LCD/VFD/VGA display.
193 To compile this driver as a module, choose M here: the
194 module will be called imon.
197 tristate "SoundGraph iMON Receiver (early raw IR models)"
200 Say Y here if you want to use a SoundGraph iMON IR Receiver,
203 To compile this driver as a module, choose M here: the
204 module will be called imon_raw.
207 tristate "Windows Media Center Ed. eHome Infrared Transceiver"
210 Say Y here if you want to use a Windows Media Center Edition
211 eHome Infrared Transceiver.
213 To compile this driver as a module, choose M here: the
214 module will be called mceusb.
217 tristate "ITE Tech Inc. IT8712/IT8512 Consumer Infrared Transceiver"
218 depends on PNP || COMPILE_TEST
220 Say Y here to enable support for integrated infrared receivers
221 /transceivers made by ITE Tech Inc. These are found in
222 several ASUS devices, like the ASUS Digimatrix or the ASUS
225 To compile this driver as a module, choose M here: the
226 module will be called ite-cir.
229 tristate "Fintek Consumer Infrared Transceiver"
230 depends on PNP || COMPILE_TEST
232 Say Y here to enable support for integrated infrared receiver
233 /transceiver made by Fintek. This chip is found on assorted
234 Jetway motherboards (and of course, possibly others).
236 To compile this driver as a module, choose M here: the
237 module will be called fintek-cir.
240 tristate "Amlogic Meson IR remote receiver"
241 depends on ARCH_MESON || COMPILE_TEST
243 Say Y if you want to use the IR remote receiver available
244 on Amlogic Meson SoCs.
246 To compile this driver as a module, choose M here: the
247 module will be called meson-ir.
250 tristate "Amlogic Meson IR TX"
251 depends on ARCH_MESON || COMPILE_TEST
253 Say Y if you want to use the IR transmitter available on
256 To compile this driver as a module, choose M here: the
257 module will be called meson-ir-tx.
260 tristate "Mediatek IR remote receiver"
261 depends on ARCH_MEDIATEK || COMPILE_TEST
263 Say Y if you want to use the IR remote receiver available
266 To compile this driver as a module, choose M here: the
267 module will be called mtk-cir.
270 tristate "Nuvoton w836x7hg Consumer Infrared Transceiver"
271 depends on PNP || COMPILE_TEST
273 Say Y here to enable support for integrated infrared receiver
274 /transceiver made by Nuvoton (formerly Winbond). This chip is
275 found in the ASRock ION 330HT, as well as assorted Intel
276 DP55-series motherboards (and of course, possibly others).
278 To compile this driver as a module, choose M here: the
279 module will be called nuvoton-cir.
282 tristate "RedRat3 IR Transceiver"
287 Say Y here if you want to use a RedRat3 Infrared Transceiver.
289 To compile this driver as a module, choose M here: the
290 module will be called redrat3.
293 tristate "SPI connected IR LED"
294 depends on SPI && LIRC
295 depends on OF || COMPILE_TEST
297 Say Y if you want to use an IR LED connected through SPI bus.
299 To compile this driver as a module, choose M here: the module will be
303 tristate "Streamzap PC Remote IR Receiver"
306 Say Y here if you want to use a Streamzap PC Remote
309 To compile this driver as a module, choose M here: the
310 module will be called streamzap.
312 config IR_WINBOND_CIR
313 tristate "Winbond IR remote control"
314 depends on (X86 && PNP) || COMPILE_TEST
319 Say Y here if you want to use the IR remote functionality found
320 in some Winbond SuperI/O chips. Currently only the WPCD376I
321 chip is supported (included in some Intel Media series
324 To compile this driver as a module, choose M here: the module will
325 be called winbond_cir.
327 config IR_IGORPLUGUSB
328 tristate "IgorPlug-USB IR Receiver"
331 Say Y here if you want to use the IgorPlug-USB IR Receiver by
332 Igor Cesko. This device is included on the Fit-PC2.
334 Note that this device can only record bursts of 36 IR pulses and
335 spaces, which is not enough for the NEC, Sanyo and RC-6 protocol.
337 To compile this driver as a module, choose M here: the module will
338 be called igorplugusb.
341 tristate "IguanaWorks USB IR Transceiver"
344 Say Y here if you want to use the IguanaWorks USB IR Transceiver.
345 Both infrared receive and send are supported. If you want to
346 change the ID or the pin config, use the user space driver from
349 Only firmware 0x0205 and later is supported.
351 To compile this driver as a module, choose M here: the module will
355 tristate "TechnoTrend USB IR Receiver"
360 Say Y here if you want to use the TechnoTrend USB IR Receiver. The
361 driver can control the led.
363 To compile this driver as a module, choose M here: the module will
367 tristate "Nokia N900 IR transmitter diode"
368 depends on (OMAP_DM_TIMER && PWM_OMAP_DMTIMER && ARCH_OMAP2PLUS || COMPILE_TEST) && RC_CORE
370 Say Y or M here if you want to enable support for the IR
371 transmitter diode built in the Nokia N900 (RX51) device.
373 The driver uses omap DM timers for generating the carrier
376 source "drivers/media/rc/img-ir/Kconfig"
379 tristate "Remote Control Loopback Driver"
381 Say Y here if you want support for the remote control loopback
382 driver which allows TX data to be sent back as RX data.
383 This is mostly useful for debugging purposes.
385 If you're not sure, select N here.
387 To compile this driver as a module, choose M here: the module will
388 be called rc_loopback.
391 tristate "GPIO IR remote control"
392 depends on (OF && GPIOLIB) || COMPILE_TEST
394 Say Y if you want to use GPIO based IR Receiver.
396 To compile this driver as a module, choose M here: the module will
397 be called gpio-ir-recv.
400 tristate "GPIO IR Bit Banging Transmitter"
402 depends on (OF && GPIOLIB) || COMPILE_TEST
404 Say Y if you want to a GPIO based IR transmitter. This is a
407 To compile this driver as a module, choose M here: the module will
408 be called gpio-ir-tx.
411 tristate "PWM IR transmitter"
414 depends on OF || COMPILE_TEST
416 Say Y if you want to use a PWM based IR transmitter. This is
417 more power efficient than the bit banging gpio driver.
419 To compile this driver as a module, choose M here: the module will
423 tristate "ST remote control receiver"
424 depends on ARCH_STI || COMPILE_TEST
426 Say Y here if you want support for ST remote control driver
427 which allows both IR and UHF RX.
428 The driver passes raw pulse and space information to the LIRC decoder.
430 If you're not sure, select N here.
433 tristate "SUNXI IR remote control"
434 depends on ARCH_SUNXI || COMPILE_TEST
436 Say Y if you want to use sunXi internal IR Controller
438 To compile this driver as a module, choose M here: the module will
442 tristate "Homebrew Serial Port Receiver"
444 Say Y if you want to use Homebrew Serial Port Receivers and
447 To compile this driver as a module, choose M here: the module will
450 config IR_SERIAL_TRANSMITTER
451 bool "Serial Port Transmitter"
454 Serial Port Transmitter support
457 tristate "Built-in SIR IrDA port"
459 Say Y if you want to use a IrDA SIR port Transceivers.
461 To compile this driver as a module, choose M here: the module will
465 tristate "Xbox DVD Movie Playback Kit"
468 Say Y here if you want to use the Xbox DVD Movie Playback Kit.
469 These are IR remotes with USB receivers for the Original Xbox (2001).
471 To compile this driver as a module, choose M here: the module will be
475 tristate "Infrared Toy and IR Droid"
478 Say Y here if you want to use the Infrared Toy or IR Droid, USB
481 To compile this driver as a module, choose M here: the module will be