1 // SPDX-License-Identifier: GPL-2.0
3 * bcm2835 sdhost driver.
5 * The 2835 has two SD controllers: The Arasan sdhci controller
6 * (supported by the iproc driver) and a custom sdhost controller
7 * (supported by this driver).
9 * The sdhci controller supports both sdcard and sdio. The sdhost
10 * controller supports the sdcard only, but has better performance.
11 * Also note that the rpi3 has sdio wifi, so driving the sdcard with
12 * the sdhost controller allows to use the sdhci controller for wifi
15 * The configuration is done by devicetree via pin muxing. Both
16 * SD controller are available on the same pins (2 pin groups = pin 22
17 * to 27 + pin 48 to 53). So it's possible to use both SD controllers
18 * at the same time with different pin groups.
20 * Author: Phil Elwell <phil@raspberrypi.org>
21 * Copyright (C) 2015-2016 Raspberry Pi (Trading) Ltd.
24 * mmc-bcm2835.c by Gellert Weisz
25 * which is, in turn, based on
26 * sdhci-bcm2708.c by Broadcom
27 * sdhci-bcm2835.c by Stephen Warren and Oleksandr Tymoshenko
28 * sdhci.c and sdhci-pci.c by Pierre Ossman
30 #include <linux/clk.h>
31 #include <linux/delay.h>
32 #include <linux/device.h>
33 #include <linux/dmaengine.h>
34 #include <linux/dma-mapping.h>
35 #include <linux/err.h>
36 #include <linux/highmem.h>
37 #include <linux/interrupt.h>
39 #include <linux/iopoll.h>
40 #include <linux/module.h>
41 #include <linux/of_address.h>
42 #include <linux/of_irq.h>
43 #include <linux/platform_device.h>
44 #include <linux/scatterlist.h>
45 #include <linux/time.h>
46 #include <linux/workqueue.h>
48 #include <linux/mmc/host.h>
49 #include <linux/mmc/mmc.h>
50 #include <linux/mmc/sd.h>
52 #define SDCMD 0x00 /* Command to SD card - 16 R/W */
53 #define SDARG 0x04 /* Argument to SD card - 32 R/W */
54 #define SDTOUT 0x08 /* Start value for timeout counter - 32 R/W */
55 #define SDCDIV 0x0c /* Start value for clock divider - 11 R/W */
56 #define SDRSP0 0x10 /* SD card response (31:0) - 32 R */
57 #define SDRSP1 0x14 /* SD card response (63:32) - 32 R */
58 #define SDRSP2 0x18 /* SD card response (95:64) - 32 R */
59 #define SDRSP3 0x1c /* SD card response (127:96) - 32 R */
60 #define SDHSTS 0x20 /* SD host status - 11 R/W */
61 #define SDVDD 0x30 /* SD card power control - 1 R/W */
62 #define SDEDM 0x34 /* Emergency Debug Mode - 13 R/W */
63 #define SDHCFG 0x38 /* Host configuration - 2 R/W */
64 #define SDHBCT 0x3c /* Host byte count (debug) - 32 R/W */
65 #define SDDATA 0x40 /* Data to/from SD card - 32 R/W */
66 #define SDHBLC 0x50 /* Host block count (SDIO/SDHC) - 9 R/W */
68 #define SDCMD_NEW_FLAG 0x8000
69 #define SDCMD_FAIL_FLAG 0x4000
70 #define SDCMD_BUSYWAIT 0x800
71 #define SDCMD_NO_RESPONSE 0x400
72 #define SDCMD_LONG_RESPONSE 0x200
73 #define SDCMD_WRITE_CMD 0x80
74 #define SDCMD_READ_CMD 0x40
75 #define SDCMD_CMD_MASK 0x3f
77 #define SDCDIV_MAX_CDIV 0x7ff
79 #define SDHSTS_BUSY_IRPT 0x400
80 #define SDHSTS_BLOCK_IRPT 0x200
81 #define SDHSTS_SDIO_IRPT 0x100
82 #define SDHSTS_REW_TIME_OUT 0x80
83 #define SDHSTS_CMD_TIME_OUT 0x40
84 #define SDHSTS_CRC16_ERROR 0x20
85 #define SDHSTS_CRC7_ERROR 0x10
86 #define SDHSTS_FIFO_ERROR 0x08
89 #define SDHSTS_DATA_FLAG 0x01
91 #define SDHSTS_TRANSFER_ERROR_MASK (SDHSTS_CRC7_ERROR | \
92 SDHSTS_CRC16_ERROR | \
93 SDHSTS_REW_TIME_OUT | \
96 #define SDHSTS_ERROR_MASK (SDHSTS_CMD_TIME_OUT | \
97 SDHSTS_TRANSFER_ERROR_MASK)
99 #define SDHCFG_BUSY_IRPT_EN BIT(10)
100 #define SDHCFG_BLOCK_IRPT_EN BIT(8)
101 #define SDHCFG_SDIO_IRPT_EN BIT(5)
102 #define SDHCFG_DATA_IRPT_EN BIT(4)
103 #define SDHCFG_SLOW_CARD BIT(3)
104 #define SDHCFG_WIDE_EXT_BUS BIT(2)
105 #define SDHCFG_WIDE_INT_BUS BIT(1)
106 #define SDHCFG_REL_CMD_LINE BIT(0)
108 #define SDVDD_POWER_OFF 0
109 #define SDVDD_POWER_ON 1
111 #define SDEDM_FORCE_DATA_MODE BIT(19)
112 #define SDEDM_CLOCK_PULSE BIT(20)
113 #define SDEDM_BYPASS BIT(21)
115 #define SDEDM_WRITE_THRESHOLD_SHIFT 9
116 #define SDEDM_READ_THRESHOLD_SHIFT 14
117 #define SDEDM_THRESHOLD_MASK 0x1f
119 #define SDEDM_FSM_MASK 0xf
120 #define SDEDM_FSM_IDENTMODE 0x0
121 #define SDEDM_FSM_DATAMODE 0x1
122 #define SDEDM_FSM_READDATA 0x2
123 #define SDEDM_FSM_WRITEDATA 0x3
124 #define SDEDM_FSM_READWAIT 0x4
125 #define SDEDM_FSM_READCRC 0x5
126 #define SDEDM_FSM_WRITECRC 0x6
127 #define SDEDM_FSM_WRITEWAIT1 0x7
128 #define SDEDM_FSM_POWERDOWN 0x8
129 #define SDEDM_FSM_POWERUP 0x9
130 #define SDEDM_FSM_WRITESTART1 0xa
131 #define SDEDM_FSM_WRITESTART2 0xb
132 #define SDEDM_FSM_GENPULSES 0xc
133 #define SDEDM_FSM_WRITEWAIT2 0xd
134 #define SDEDM_FSM_STARTPOWDOWN 0xf
136 #define SDDATA_FIFO_WORDS 16
138 #define FIFO_READ_THRESHOLD 4
139 #define FIFO_WRITE_THRESHOLD 4
140 #define SDDATA_FIFO_PIO_BURST 8
142 #define PIO_THRESHOLD 1 /* Maximum block count for PIO (0 = always DMA) */
144 struct bcm2835_host
{
148 void __iomem
*ioaddr
;
151 struct mmc_host
*mmc
;
152 struct platform_device
*pdev
;
154 int clock
; /* Current clock speed */
155 unsigned int max_clk
; /* Max possible freq */
156 struct work_struct dma_work
;
157 struct delayed_work timeout_work
; /* Timer for timeouts */
158 struct sg_mapping_iter sg_miter
; /* SG state for PIO */
159 unsigned int blocks
; /* remaining PIO blocks */
160 int irq
; /* Device IRQ */
162 u32 ns_per_fifo_word
;
164 /* cached registers */
168 struct mmc_request
*mrq
; /* Current request */
169 struct mmc_command
*cmd
; /* Current command */
170 struct mmc_data
*data
; /* Current data request */
171 bool data_complete
:1;/* Data finished before cmd */
172 bool use_busy
:1; /* Wait for busy interrupt */
173 bool use_sbc
:1; /* Send CMD23 */
175 /* for threaded irq handler */
181 struct dma_chan
*dma_chan_rxtx
;
182 struct dma_chan
*dma_chan
;
183 struct dma_slave_config dma_cfg_rx
;
184 struct dma_slave_config dma_cfg_tx
;
185 struct dma_async_tx_descriptor
*dma_desc
;
188 struct page
*drain_page
;
193 static void bcm2835_dumpcmd(struct bcm2835_host
*host
, struct mmc_command
*cmd
,
196 struct device
*dev
= &host
->pdev
->dev
;
201 dev_dbg(dev
, "%c%s op %d arg 0x%x flags 0x%x - resp %08x %08x %08x %08x, err %d\n",
202 (cmd
== host
->cmd
) ? '>' : ' ',
203 label
, cmd
->opcode
, cmd
->arg
, cmd
->flags
,
204 cmd
->resp
[0], cmd
->resp
[1], cmd
->resp
[2], cmd
->resp
[3],
208 static void bcm2835_dumpregs(struct bcm2835_host
*host
)
210 struct mmc_request
*mrq
= host
->mrq
;
211 struct device
*dev
= &host
->pdev
->dev
;
214 bcm2835_dumpcmd(host
, mrq
->sbc
, "sbc");
215 bcm2835_dumpcmd(host
, mrq
->cmd
, "cmd");
217 dev_dbg(dev
, "data blocks %x blksz %x - err %d\n",
222 bcm2835_dumpcmd(host
, mrq
->stop
, "stop");
225 dev_dbg(dev
, "=========== REGISTER DUMP ===========\n");
226 dev_dbg(dev
, "SDCMD 0x%08x\n", readl(host
->ioaddr
+ SDCMD
));
227 dev_dbg(dev
, "SDARG 0x%08x\n", readl(host
->ioaddr
+ SDARG
));
228 dev_dbg(dev
, "SDTOUT 0x%08x\n", readl(host
->ioaddr
+ SDTOUT
));
229 dev_dbg(dev
, "SDCDIV 0x%08x\n", readl(host
->ioaddr
+ SDCDIV
));
230 dev_dbg(dev
, "SDRSP0 0x%08x\n", readl(host
->ioaddr
+ SDRSP0
));
231 dev_dbg(dev
, "SDRSP1 0x%08x\n", readl(host
->ioaddr
+ SDRSP1
));
232 dev_dbg(dev
, "SDRSP2 0x%08x\n", readl(host
->ioaddr
+ SDRSP2
));
233 dev_dbg(dev
, "SDRSP3 0x%08x\n", readl(host
->ioaddr
+ SDRSP3
));
234 dev_dbg(dev
, "SDHSTS 0x%08x\n", readl(host
->ioaddr
+ SDHSTS
));
235 dev_dbg(dev
, "SDVDD 0x%08x\n", readl(host
->ioaddr
+ SDVDD
));
236 dev_dbg(dev
, "SDEDM 0x%08x\n", readl(host
->ioaddr
+ SDEDM
));
237 dev_dbg(dev
, "SDHCFG 0x%08x\n", readl(host
->ioaddr
+ SDHCFG
));
238 dev_dbg(dev
, "SDHBCT 0x%08x\n", readl(host
->ioaddr
+ SDHBCT
));
239 dev_dbg(dev
, "SDHBLC 0x%08x\n", readl(host
->ioaddr
+ SDHBLC
));
240 dev_dbg(dev
, "===========================================\n");
243 static void bcm2835_reset_internal(struct bcm2835_host
*host
)
247 writel(SDVDD_POWER_OFF
, host
->ioaddr
+ SDVDD
);
248 writel(0, host
->ioaddr
+ SDCMD
);
249 writel(0, host
->ioaddr
+ SDARG
);
250 writel(0xf00000, host
->ioaddr
+ SDTOUT
);
251 writel(0, host
->ioaddr
+ SDCDIV
);
252 writel(0x7f8, host
->ioaddr
+ SDHSTS
); /* Write 1s to clear */
253 writel(0, host
->ioaddr
+ SDHCFG
);
254 writel(0, host
->ioaddr
+ SDHBCT
);
255 writel(0, host
->ioaddr
+ SDHBLC
);
257 /* Limit fifo usage due to silicon bug */
258 temp
= readl(host
->ioaddr
+ SDEDM
);
259 temp
&= ~((SDEDM_THRESHOLD_MASK
<< SDEDM_READ_THRESHOLD_SHIFT
) |
260 (SDEDM_THRESHOLD_MASK
<< SDEDM_WRITE_THRESHOLD_SHIFT
));
261 temp
|= (FIFO_READ_THRESHOLD
<< SDEDM_READ_THRESHOLD_SHIFT
) |
262 (FIFO_WRITE_THRESHOLD
<< SDEDM_WRITE_THRESHOLD_SHIFT
);
263 writel(temp
, host
->ioaddr
+ SDEDM
);
265 writel(SDVDD_POWER_ON
, host
->ioaddr
+ SDVDD
);
268 writel(host
->hcfg
, host
->ioaddr
+ SDHCFG
);
269 writel(host
->cdiv
, host
->ioaddr
+ SDCDIV
);
272 static void bcm2835_reset(struct mmc_host
*mmc
)
274 struct bcm2835_host
*host
= mmc_priv(mmc
);
277 dmaengine_terminate_sync(host
->dma_chan
);
278 host
->dma_chan
= NULL
;
279 bcm2835_reset_internal(host
);
282 static void bcm2835_finish_command(struct bcm2835_host
*host
);
284 static void bcm2835_wait_transfer_complete(struct bcm2835_host
*host
)
289 alternate_idle
= (host
->mrq
->data
->flags
& MMC_DATA_READ
) ?
290 SDEDM_FSM_READWAIT
: SDEDM_FSM_WRITESTART1
;
297 edm
= readl(host
->ioaddr
+ SDEDM
);
298 fsm
= edm
& SDEDM_FSM_MASK
;
300 if ((fsm
== SDEDM_FSM_IDENTMODE
) ||
301 (fsm
== SDEDM_FSM_DATAMODE
))
303 if (fsm
== alternate_idle
) {
304 writel(edm
| SDEDM_FORCE_DATA_MODE
,
305 host
->ioaddr
+ SDEDM
);
310 if (timediff
== 100000) {
311 dev_err(&host
->pdev
->dev
,
312 "wait_transfer_complete - still waiting after %d retries\n",
314 bcm2835_dumpregs(host
);
315 host
->mrq
->data
->error
= -ETIMEDOUT
;
322 static void bcm2835_dma_complete(void *param
)
324 struct bcm2835_host
*host
= param
;
326 schedule_work(&host
->dma_work
);
329 static void bcm2835_transfer_block_pio(struct bcm2835_host
*host
, bool is_read
)
333 unsigned long wait_max
;
335 blksize
= host
->data
->blksz
;
337 wait_max
= jiffies
+ msecs_to_jiffies(500);
339 local_irq_save(flags
);
347 if (!sg_miter_next(&host
->sg_miter
)) {
348 host
->data
->error
= -EINVAL
;
352 len
= min(host
->sg_miter
.length
, blksize
);
354 host
->data
->error
= -EINVAL
;
359 host
->sg_miter
.consumed
= len
;
361 buf
= (u32
*)host
->sg_miter
.addr
;
363 copy_words
= len
/ 4;
366 int burst_words
, words
;
369 burst_words
= min(SDDATA_FIFO_PIO_BURST
, copy_words
);
370 edm
= readl(host
->ioaddr
+ SDEDM
);
372 words
= ((edm
>> 4) & 0x1f);
374 words
= SDDATA_FIFO_WORDS
- ((edm
>> 4) & 0x1f);
376 if (words
< burst_words
) {
377 int fsm_state
= (edm
& SDEDM_FSM_MASK
);
378 struct device
*dev
= &host
->pdev
->dev
;
381 (fsm_state
!= SDEDM_FSM_READDATA
&&
382 fsm_state
!= SDEDM_FSM_READWAIT
&&
383 fsm_state
!= SDEDM_FSM_READCRC
)) ||
385 (fsm_state
!= SDEDM_FSM_WRITEDATA
&&
386 fsm_state
!= SDEDM_FSM_WRITESTART1
&&
387 fsm_state
!= SDEDM_FSM_WRITESTART2
))) {
388 hsts
= readl(host
->ioaddr
+ SDHSTS
);
389 dev_err(dev
, "fsm %x, hsts %08x\n",
391 if (hsts
& SDHSTS_ERROR_MASK
)
395 if (time_after(jiffies
, wait_max
)) {
396 dev_err(dev
, "PIO %s timeout - EDM %08x\n",
397 is_read
? "read" : "write",
399 hsts
= SDHSTS_REW_TIME_OUT
;
402 ndelay((burst_words
- words
) *
403 host
->ns_per_fifo_word
);
405 } else if (words
> copy_words
) {
413 *(buf
++) = readl(host
->ioaddr
+ SDDATA
);
415 writel(*(buf
++), host
->ioaddr
+ SDDATA
);
420 if (hsts
& SDHSTS_ERROR_MASK
)
424 sg_miter_stop(&host
->sg_miter
);
426 local_irq_restore(flags
);
429 static void bcm2835_transfer_pio(struct bcm2835_host
*host
)
431 struct device
*dev
= &host
->pdev
->dev
;
435 is_read
= (host
->data
->flags
& MMC_DATA_READ
) != 0;
436 bcm2835_transfer_block_pio(host
, is_read
);
438 sdhsts
= readl(host
->ioaddr
+ SDHSTS
);
439 if (sdhsts
& (SDHSTS_CRC16_ERROR
|
441 SDHSTS_FIFO_ERROR
)) {
442 dev_err(dev
, "%s transfer error - HSTS %08x\n",
443 is_read
? "read" : "write", sdhsts
);
444 host
->data
->error
= -EILSEQ
;
445 } else if ((sdhsts
& (SDHSTS_CMD_TIME_OUT
|
446 SDHSTS_REW_TIME_OUT
))) {
447 dev_err(dev
, "%s timeout error - HSTS %08x\n",
448 is_read
? "read" : "write", sdhsts
);
449 host
->data
->error
= -ETIMEDOUT
;
454 void bcm2835_prepare_dma(struct bcm2835_host
*host
, struct mmc_data
*data
)
456 int sg_len
, dir_data
, dir_slave
;
457 struct dma_async_tx_descriptor
*desc
= NULL
;
458 struct dma_chan
*dma_chan
;
460 dma_chan
= host
->dma_chan_rxtx
;
461 if (data
->flags
& MMC_DATA_READ
) {
462 dir_data
= DMA_FROM_DEVICE
;
463 dir_slave
= DMA_DEV_TO_MEM
;
465 dir_data
= DMA_TO_DEVICE
;
466 dir_slave
= DMA_MEM_TO_DEV
;
469 /* The block doesn't manage the FIFO DREQs properly for
470 * multi-block transfers, so don't attempt to DMA the final
471 * few words. Unfortunately this requires the final sg entry
472 * to be trimmed. N.B. This code demands that the overspill
473 * is contained in a single sg entry.
476 host
->drain_words
= 0;
477 if ((data
->blocks
> 1) && (dir_data
== DMA_FROM_DEVICE
)) {
478 struct scatterlist
*sg
;
482 len
= min((u32
)(FIFO_READ_THRESHOLD
- 1) * 4,
483 (u32
)data
->blocks
* data
->blksz
);
485 for_each_sg(data
->sg
, sg
, data
->sg_len
, i
) {
486 if (sg_is_last(sg
)) {
487 WARN_ON(sg
->length
< len
);
489 host
->drain_page
= sg_page(sg
);
490 host
->drain_offset
= sg
->offset
+ sg
->length
;
493 host
->drain_words
= len
/ 4;
496 /* The parameters have already been validated, so this will not fail */
497 (void)dmaengine_slave_config(dma_chan
,
498 (dir_data
== DMA_FROM_DEVICE
) ?
502 sg_len
= dma_map_sg(dma_chan
->device
->dev
, data
->sg
, data
->sg_len
,
507 desc
= dmaengine_prep_slave_sg(dma_chan
, data
->sg
, sg_len
, dir_slave
,
508 DMA_PREP_INTERRUPT
| DMA_CTRL_ACK
);
511 dma_unmap_sg(dma_chan
->device
->dev
, data
->sg
, sg_len
, dir_data
);
515 desc
->callback
= bcm2835_dma_complete
;
516 desc
->callback_param
= host
;
517 host
->dma_desc
= desc
;
518 host
->dma_chan
= dma_chan
;
519 host
->dma_dir
= dir_data
;
522 static void bcm2835_start_dma(struct bcm2835_host
*host
)
524 dmaengine_submit(host
->dma_desc
);
525 dma_async_issue_pending(host
->dma_chan
);
528 static void bcm2835_set_transfer_irqs(struct bcm2835_host
*host
)
530 u32 all_irqs
= SDHCFG_DATA_IRPT_EN
| SDHCFG_BLOCK_IRPT_EN
|
533 if (host
->dma_desc
) {
534 host
->hcfg
= (host
->hcfg
& ~all_irqs
) |
537 host
->hcfg
= (host
->hcfg
& ~all_irqs
) |
538 SDHCFG_DATA_IRPT_EN
|
542 writel(host
->hcfg
, host
->ioaddr
+ SDHCFG
);
546 void bcm2835_prepare_data(struct bcm2835_host
*host
, struct mmc_command
*cmd
)
548 struct mmc_data
*data
= cmd
->data
;
556 host
->data_complete
= false;
557 host
->data
->bytes_xfered
= 0;
559 if (!host
->dma_desc
) {
561 int flags
= SG_MITER_ATOMIC
;
563 if (data
->flags
& MMC_DATA_READ
)
564 flags
|= SG_MITER_TO_SG
;
566 flags
|= SG_MITER_FROM_SG
;
567 sg_miter_start(&host
->sg_miter
, data
->sg
, data
->sg_len
, flags
);
568 host
->blocks
= data
->blocks
;
571 bcm2835_set_transfer_irqs(host
);
573 writel(data
->blksz
, host
->ioaddr
+ SDHBCT
);
574 writel(data
->blocks
, host
->ioaddr
+ SDHBLC
);
577 static u32
bcm2835_read_wait_sdcmd(struct bcm2835_host
*host
, u32 max_ms
)
579 struct device
*dev
= &host
->pdev
->dev
;
583 ret
= readl_poll_timeout(host
->ioaddr
+ SDCMD
, value
,
584 !(value
& SDCMD_NEW_FLAG
), 1, 10);
585 if (ret
== -ETIMEDOUT
)
586 /* if it takes a while make poll interval bigger */
587 ret
= readl_poll_timeout(host
->ioaddr
+ SDCMD
, value
,
588 !(value
& SDCMD_NEW_FLAG
),
590 if (ret
== -ETIMEDOUT
)
591 dev_err(dev
, "%s: timeout (%d ms)\n", __func__
, max_ms
);
596 static void bcm2835_finish_request(struct bcm2835_host
*host
)
598 struct dma_chan
*terminate_chan
= NULL
;
599 struct mmc_request
*mrq
;
601 cancel_delayed_work_sync(&host
->timeout_work
);
609 host
->dma_desc
= NULL
;
610 terminate_chan
= host
->dma_chan
;
611 host
->dma_chan
= NULL
;
613 if (terminate_chan
) {
614 int err
= dmaengine_terminate_all(terminate_chan
);
617 dev_err(&host
->pdev
->dev
,
618 "failed to terminate DMA (%d)\n", err
);
621 mmc_request_done(host
->mmc
, mrq
);
625 bool bcm2835_send_command(struct bcm2835_host
*host
, struct mmc_command
*cmd
)
627 struct device
*dev
= &host
->pdev
->dev
;
629 unsigned long timeout
;
633 sdcmd
= bcm2835_read_wait_sdcmd(host
, 100);
634 if (sdcmd
& SDCMD_NEW_FLAG
) {
635 dev_err(dev
, "previous command never completed.\n");
636 bcm2835_dumpregs(host
);
637 cmd
->error
= -EILSEQ
;
638 bcm2835_finish_request(host
);
642 if (!cmd
->data
&& cmd
->busy_timeout
> 9000)
643 timeout
= DIV_ROUND_UP(cmd
->busy_timeout
, 1000) * HZ
+ HZ
;
646 schedule_delayed_work(&host
->timeout_work
, timeout
);
650 /* Clear any error flags */
651 sdhsts
= readl(host
->ioaddr
+ SDHSTS
);
652 if (sdhsts
& SDHSTS_ERROR_MASK
)
653 writel(sdhsts
, host
->ioaddr
+ SDHSTS
);
655 if ((cmd
->flags
& MMC_RSP_136
) && (cmd
->flags
& MMC_RSP_BUSY
)) {
656 dev_err(dev
, "unsupported response type!\n");
657 cmd
->error
= -EINVAL
;
658 bcm2835_finish_request(host
);
662 bcm2835_prepare_data(host
, cmd
);
664 writel(cmd
->arg
, host
->ioaddr
+ SDARG
);
666 sdcmd
= cmd
->opcode
& SDCMD_CMD_MASK
;
668 host
->use_busy
= false;
669 if (!(cmd
->flags
& MMC_RSP_PRESENT
)) {
670 sdcmd
|= SDCMD_NO_RESPONSE
;
672 if (cmd
->flags
& MMC_RSP_136
)
673 sdcmd
|= SDCMD_LONG_RESPONSE
;
674 if (cmd
->flags
& MMC_RSP_BUSY
) {
675 sdcmd
|= SDCMD_BUSYWAIT
;
676 host
->use_busy
= true;
681 if (cmd
->data
->flags
& MMC_DATA_WRITE
)
682 sdcmd
|= SDCMD_WRITE_CMD
;
683 if (cmd
->data
->flags
& MMC_DATA_READ
)
684 sdcmd
|= SDCMD_READ_CMD
;
687 writel(sdcmd
| SDCMD_NEW_FLAG
, host
->ioaddr
+ SDCMD
);
692 static void bcm2835_transfer_complete(struct bcm2835_host
*host
)
694 struct mmc_data
*data
;
696 WARN_ON(!host
->data_complete
);
701 /* Need to send CMD12 if -
702 * a) open-ended multiblock transfer (no CMD23)
703 * b) error in multiblock transfer
705 if (host
->mrq
->stop
&& (data
->error
|| !host
->use_sbc
)) {
706 if (bcm2835_send_command(host
, host
->mrq
->stop
)) {
707 /* No busy, so poll for completion */
709 bcm2835_finish_command(host
);
712 bcm2835_wait_transfer_complete(host
);
713 bcm2835_finish_request(host
);
717 static void bcm2835_finish_data(struct bcm2835_host
*host
)
719 struct device
*dev
= &host
->pdev
->dev
;
720 struct mmc_data
*data
;
724 host
->hcfg
&= ~(SDHCFG_DATA_IRPT_EN
| SDHCFG_BLOCK_IRPT_EN
);
725 writel(host
->hcfg
, host
->ioaddr
+ SDHCFG
);
727 data
->bytes_xfered
= data
->error
? 0 : (data
->blksz
* data
->blocks
);
729 host
->data_complete
= true;
732 /* Data managed to finish before the
733 * command completed. Make sure we do
734 * things in the proper order.
736 dev_dbg(dev
, "Finished early - HSTS %08x\n",
737 readl(host
->ioaddr
+ SDHSTS
));
739 bcm2835_transfer_complete(host
);
743 static void bcm2835_finish_command(struct bcm2835_host
*host
)
745 struct device
*dev
= &host
->pdev
->dev
;
746 struct mmc_command
*cmd
= host
->cmd
;
749 sdcmd
= bcm2835_read_wait_sdcmd(host
, 100);
751 /* Check for errors */
752 if (sdcmd
& SDCMD_NEW_FLAG
) {
753 dev_err(dev
, "command never completed.\n");
754 bcm2835_dumpregs(host
);
755 host
->cmd
->error
= -EIO
;
756 bcm2835_finish_request(host
);
758 } else if (sdcmd
& SDCMD_FAIL_FLAG
) {
759 u32 sdhsts
= readl(host
->ioaddr
+ SDHSTS
);
761 /* Clear the errors */
762 writel(SDHSTS_ERROR_MASK
, host
->ioaddr
+ SDHSTS
);
764 if (!(sdhsts
& SDHSTS_CRC7_ERROR
) ||
765 (host
->cmd
->opcode
!= MMC_SEND_OP_COND
)) {
768 if (sdhsts
& SDHSTS_CMD_TIME_OUT
) {
769 host
->cmd
->error
= -ETIMEDOUT
;
771 dev_err(dev
, "unexpected command %d error\n",
773 bcm2835_dumpregs(host
);
774 host
->cmd
->error
= -EILSEQ
;
776 edm
= readl(host
->ioaddr
+ SDEDM
);
777 fsm
= edm
& SDEDM_FSM_MASK
;
778 if (fsm
== SDEDM_FSM_READWAIT
||
779 fsm
== SDEDM_FSM_WRITESTART1
)
780 /* Kick the FSM out of its wait */
781 writel(edm
| SDEDM_FORCE_DATA_MODE
,
782 host
->ioaddr
+ SDEDM
);
783 bcm2835_finish_request(host
);
788 if (cmd
->flags
& MMC_RSP_PRESENT
) {
789 if (cmd
->flags
& MMC_RSP_136
) {
792 for (i
= 0; i
< 4; i
++) {
794 readl(host
->ioaddr
+ SDRSP0
+ i
* 4);
797 cmd
->resp
[0] = readl(host
->ioaddr
+ SDRSP0
);
801 if (cmd
== host
->mrq
->sbc
) {
802 /* Finished CMD23, now send actual command. */
804 if (bcm2835_send_command(host
, host
->mrq
->cmd
)) {
805 if (host
->data
&& host
->dma_desc
)
806 /* DMA transfer starts now, PIO starts
809 bcm2835_start_dma(host
);
812 bcm2835_finish_command(host
);
814 } else if (cmd
== host
->mrq
->stop
) {
816 bcm2835_finish_request(host
);
818 /* Processed actual command. */
821 bcm2835_finish_request(host
);
822 else if (host
->data_complete
)
823 bcm2835_transfer_complete(host
);
827 static void bcm2835_timeout(struct work_struct
*work
)
829 struct delayed_work
*d
= to_delayed_work(work
);
830 struct bcm2835_host
*host
=
831 container_of(d
, struct bcm2835_host
, timeout_work
);
832 struct device
*dev
= &host
->pdev
->dev
;
834 mutex_lock(&host
->mutex
);
837 dev_err(dev
, "timeout waiting for hardware interrupt.\n");
838 bcm2835_dumpregs(host
);
840 bcm2835_reset(host
->mmc
);
843 host
->data
->error
= -ETIMEDOUT
;
844 bcm2835_finish_data(host
);
847 host
->cmd
->error
= -ETIMEDOUT
;
849 host
->mrq
->cmd
->error
= -ETIMEDOUT
;
851 bcm2835_finish_request(host
);
855 mutex_unlock(&host
->mutex
);
858 static bool bcm2835_check_cmd_error(struct bcm2835_host
*host
, u32 intmask
)
860 struct device
*dev
= &host
->pdev
->dev
;
862 if (!(intmask
& SDHSTS_ERROR_MASK
))
868 dev_err(dev
, "sdhost_busy_irq: intmask %08x\n", intmask
);
869 if (intmask
& SDHSTS_CRC7_ERROR
) {
870 host
->cmd
->error
= -EILSEQ
;
871 } else if (intmask
& (SDHSTS_CRC16_ERROR
|
872 SDHSTS_FIFO_ERROR
)) {
874 host
->mrq
->data
->error
= -EILSEQ
;
876 host
->cmd
->error
= -EILSEQ
;
877 } else if (intmask
& SDHSTS_REW_TIME_OUT
) {
879 host
->mrq
->data
->error
= -ETIMEDOUT
;
881 host
->cmd
->error
= -ETIMEDOUT
;
882 } else if (intmask
& SDHSTS_CMD_TIME_OUT
) {
883 host
->cmd
->error
= -ETIMEDOUT
;
885 bcm2835_dumpregs(host
);
889 static void bcm2835_check_data_error(struct bcm2835_host
*host
, u32 intmask
)
893 if (intmask
& (SDHSTS_CRC16_ERROR
| SDHSTS_FIFO_ERROR
))
894 host
->data
->error
= -EILSEQ
;
895 if (intmask
& SDHSTS_REW_TIME_OUT
)
896 host
->data
->error
= -ETIMEDOUT
;
899 static void bcm2835_busy_irq(struct bcm2835_host
*host
)
901 if (WARN_ON(!host
->cmd
)) {
902 bcm2835_dumpregs(host
);
906 if (WARN_ON(!host
->use_busy
)) {
907 bcm2835_dumpregs(host
);
910 host
->use_busy
= false;
912 bcm2835_finish_command(host
);
915 static void bcm2835_data_irq(struct bcm2835_host
*host
, u32 intmask
)
917 /* There are no dedicated data/space available interrupt
918 * status bits, so it is necessary to use the single shared
919 * data/space available FIFO status bits. It is therefore not
920 * an error to get here when there is no data transfer in
926 bcm2835_check_data_error(host
, intmask
);
927 if (host
->data
->error
)
930 if (host
->data
->flags
& MMC_DATA_WRITE
) {
931 /* Use the block interrupt for writes after the first block */
932 host
->hcfg
&= ~(SDHCFG_DATA_IRPT_EN
);
933 host
->hcfg
|= SDHCFG_BLOCK_IRPT_EN
;
934 writel(host
->hcfg
, host
->ioaddr
+ SDHCFG
);
935 bcm2835_transfer_pio(host
);
937 bcm2835_transfer_pio(host
);
939 if ((host
->blocks
== 0) || host
->data
->error
)
945 host
->hcfg
&= ~(SDHCFG_DATA_IRPT_EN
| SDHCFG_BLOCK_IRPT_EN
);
946 writel(host
->hcfg
, host
->ioaddr
+ SDHCFG
);
949 static void bcm2835_data_threaded_irq(struct bcm2835_host
*host
)
953 if ((host
->blocks
== 0) || host
->data
->error
)
954 bcm2835_finish_data(host
);
957 static void bcm2835_block_irq(struct bcm2835_host
*host
)
959 if (WARN_ON(!host
->data
)) {
960 bcm2835_dumpregs(host
);
964 if (!host
->dma_desc
) {
965 WARN_ON(!host
->blocks
);
966 if (host
->data
->error
|| (--host
->blocks
== 0))
967 bcm2835_finish_data(host
);
969 bcm2835_transfer_pio(host
);
970 } else if (host
->data
->flags
& MMC_DATA_WRITE
) {
971 bcm2835_finish_data(host
);
975 static irqreturn_t
bcm2835_irq(int irq
, void *dev_id
)
977 irqreturn_t result
= IRQ_NONE
;
978 struct bcm2835_host
*host
= dev_id
;
981 spin_lock(&host
->lock
);
983 intmask
= readl(host
->ioaddr
+ SDHSTS
);
985 writel(SDHSTS_BUSY_IRPT
|
989 host
->ioaddr
+ SDHSTS
);
991 if (intmask
& SDHSTS_BLOCK_IRPT
) {
992 bcm2835_check_data_error(host
, intmask
);
993 host
->irq_block
= true;
994 result
= IRQ_WAKE_THREAD
;
997 if (intmask
& SDHSTS_BUSY_IRPT
) {
998 if (!bcm2835_check_cmd_error(host
, intmask
)) {
999 host
->irq_busy
= true;
1000 result
= IRQ_WAKE_THREAD
;
1002 result
= IRQ_HANDLED
;
1006 /* There is no true data interrupt status bit, so it is
1007 * necessary to qualify the data flag with the interrupt
1010 if ((intmask
& SDHSTS_DATA_FLAG
) &&
1011 (host
->hcfg
& SDHCFG_DATA_IRPT_EN
)) {
1012 bcm2835_data_irq(host
, intmask
);
1013 host
->irq_data
= true;
1014 result
= IRQ_WAKE_THREAD
;
1017 spin_unlock(&host
->lock
);
1022 static irqreturn_t
bcm2835_threaded_irq(int irq
, void *dev_id
)
1024 struct bcm2835_host
*host
= dev_id
;
1025 unsigned long flags
;
1026 bool block
, busy
, data
;
1028 spin_lock_irqsave(&host
->lock
, flags
);
1030 block
= host
->irq_block
;
1031 busy
= host
->irq_busy
;
1032 data
= host
->irq_data
;
1033 host
->irq_block
= false;
1034 host
->irq_busy
= false;
1035 host
->irq_data
= false;
1037 spin_unlock_irqrestore(&host
->lock
, flags
);
1039 mutex_lock(&host
->mutex
);
1042 bcm2835_block_irq(host
);
1044 bcm2835_busy_irq(host
);
1046 bcm2835_data_threaded_irq(host
);
1048 mutex_unlock(&host
->mutex
);
1053 static void bcm2835_dma_complete_work(struct work_struct
*work
)
1055 struct bcm2835_host
*host
=
1056 container_of(work
, struct bcm2835_host
, dma_work
);
1057 struct mmc_data
*data
;
1059 mutex_lock(&host
->mutex
);
1063 if (host
->dma_chan
) {
1064 dma_unmap_sg(host
->dma_chan
->device
->dev
,
1065 data
->sg
, data
->sg_len
,
1068 host
->dma_chan
= NULL
;
1071 if (host
->drain_words
) {
1072 unsigned long flags
;
1076 if (host
->drain_offset
& PAGE_MASK
) {
1077 host
->drain_page
+= host
->drain_offset
>> PAGE_SHIFT
;
1078 host
->drain_offset
&= ~PAGE_MASK
;
1080 local_irq_save(flags
);
1081 page
= kmap_atomic(host
->drain_page
);
1082 buf
= page
+ host
->drain_offset
;
1084 while (host
->drain_words
) {
1085 u32 edm
= readl(host
->ioaddr
+ SDEDM
);
1087 if ((edm
>> 4) & 0x1f)
1088 *(buf
++) = readl(host
->ioaddr
+ SDDATA
);
1089 host
->drain_words
--;
1092 kunmap_atomic(page
);
1093 local_irq_restore(flags
);
1096 bcm2835_finish_data(host
);
1098 mutex_unlock(&host
->mutex
);
1101 static void bcm2835_set_clock(struct bcm2835_host
*host
, unsigned int clock
)
1105 /* The SDCDIV register has 11 bits, and holds (div - 2). But
1106 * in data mode the max is 50MHz wihout a minimum, and only
1107 * the bottom 3 bits are used. Since the switch over is
1108 * automatic (unless we have marked the card as slow...),
1109 * chosen values have to make sense in both modes. Ident mode
1110 * must be 100-400KHz, so can range check the requested
1111 * clock. CMD15 must be used to return to data mode, so this
1114 * clock 250MHz -> 0->125MHz, 1->83.3MHz, 2->62.5MHz, 3->50.0MHz
1115 * 4->41.7MHz, 5->35.7MHz, 6->31.3MHz, 7->27.8MHz
1117 * 623->400KHz/27.8MHz
1118 * reset value (507)->491159/50MHz
1120 * BUT, the 3-bit clock divisor in data mode is too small if
1121 * the core clock is higher than 250MHz, so instead use the
1122 * SLOW_CARD configuration bit to force the use of the ident
1123 * clock divisor at all times.
1126 if (clock
< 100000) {
1127 /* Can't stop the clock, but make it as slow as possible
1130 host
->cdiv
= SDCDIV_MAX_CDIV
;
1131 writel(host
->cdiv
, host
->ioaddr
+ SDCDIV
);
1135 div
= host
->max_clk
/ clock
;
1138 if ((host
->max_clk
/ div
) > clock
)
1142 if (div
> SDCDIV_MAX_CDIV
)
1143 div
= SDCDIV_MAX_CDIV
;
1145 clock
= host
->max_clk
/ (div
+ 2);
1146 host
->mmc
->actual_clock
= clock
;
1148 /* Calibrate some delays */
1150 host
->ns_per_fifo_word
= (1000000000 / clock
) *
1151 ((host
->mmc
->caps
& MMC_CAP_4_BIT_DATA
) ? 8 : 32);
1154 writel(host
->cdiv
, host
->ioaddr
+ SDCDIV
);
1156 /* Set the timeout to 500ms */
1157 writel(host
->mmc
->actual_clock
/ 2, host
->ioaddr
+ SDTOUT
);
1160 static void bcm2835_request(struct mmc_host
*mmc
, struct mmc_request
*mrq
)
1162 struct bcm2835_host
*host
= mmc_priv(mmc
);
1163 struct device
*dev
= &host
->pdev
->dev
;
1166 /* Reset the error statuses in case this is a retry */
1168 mrq
->sbc
->error
= 0;
1170 mrq
->cmd
->error
= 0;
1172 mrq
->data
->error
= 0;
1174 mrq
->stop
->error
= 0;
1176 if (mrq
->data
&& !is_power_of_2(mrq
->data
->blksz
)) {
1177 dev_err(dev
, "unsupported block size (%d bytes)\n",
1181 mrq
->cmd
->error
= -EINVAL
;
1183 mmc_request_done(mmc
, mrq
);
1187 mutex_lock(&host
->mutex
);
1192 edm
= readl(host
->ioaddr
+ SDEDM
);
1193 fsm
= edm
& SDEDM_FSM_MASK
;
1195 if ((fsm
!= SDEDM_FSM_IDENTMODE
) &&
1196 (fsm
!= SDEDM_FSM_DATAMODE
)) {
1197 dev_err(dev
, "previous command (%d) not complete (EDM %08x)\n",
1198 readl(host
->ioaddr
+ SDCMD
) & SDCMD_CMD_MASK
,
1200 bcm2835_dumpregs(host
);
1203 mrq
->cmd
->error
= -EILSEQ
;
1205 bcm2835_finish_request(host
);
1206 mutex_unlock(&host
->mutex
);
1210 if (host
->use_dma
&& mrq
->data
&& (mrq
->data
->blocks
> PIO_THRESHOLD
))
1211 bcm2835_prepare_dma(host
, mrq
->data
);
1213 host
->use_sbc
= !!mrq
->sbc
&& host
->mrq
->data
&&
1214 (host
->mrq
->data
->flags
& MMC_DATA_READ
);
1215 if (host
->use_sbc
) {
1216 if (bcm2835_send_command(host
, mrq
->sbc
)) {
1217 if (!host
->use_busy
)
1218 bcm2835_finish_command(host
);
1220 } else if (mrq
->cmd
&& bcm2835_send_command(host
, mrq
->cmd
)) {
1221 if (host
->data
&& host
->dma_desc
) {
1222 /* DMA transfer starts now, PIO starts after irq */
1223 bcm2835_start_dma(host
);
1226 if (!host
->use_busy
)
1227 bcm2835_finish_command(host
);
1230 mutex_unlock(&host
->mutex
);
1233 static void bcm2835_set_ios(struct mmc_host
*mmc
, struct mmc_ios
*ios
)
1235 struct bcm2835_host
*host
= mmc_priv(mmc
);
1237 mutex_lock(&host
->mutex
);
1239 if (!ios
->clock
|| ios
->clock
!= host
->clock
) {
1240 bcm2835_set_clock(host
, ios
->clock
);
1241 host
->clock
= ios
->clock
;
1245 host
->hcfg
&= ~SDHCFG_WIDE_EXT_BUS
;
1246 if (ios
->bus_width
== MMC_BUS_WIDTH_4
)
1247 host
->hcfg
|= SDHCFG_WIDE_EXT_BUS
;
1249 host
->hcfg
|= SDHCFG_WIDE_INT_BUS
;
1251 /* Disable clever clock switching, to cope with fast core clocks */
1252 host
->hcfg
|= SDHCFG_SLOW_CARD
;
1254 writel(host
->hcfg
, host
->ioaddr
+ SDHCFG
);
1256 mutex_unlock(&host
->mutex
);
1259 static const struct mmc_host_ops bcm2835_ops
= {
1260 .request
= bcm2835_request
,
1261 .set_ios
= bcm2835_set_ios
,
1262 .hw_reset
= bcm2835_reset
,
1265 static int bcm2835_add_host(struct bcm2835_host
*host
)
1267 struct mmc_host
*mmc
= host
->mmc
;
1268 struct device
*dev
= &host
->pdev
->dev
;
1269 char pio_limit_string
[20];
1272 if (!mmc
->f_max
|| mmc
->f_max
> host
->max_clk
)
1273 mmc
->f_max
= host
->max_clk
;
1274 mmc
->f_min
= host
->max_clk
/ SDCDIV_MAX_CDIV
;
1276 mmc
->max_busy_timeout
= ~0 / (mmc
->f_max
/ 1000);
1278 dev_dbg(dev
, "f_max %d, f_min %d, max_busy_timeout %d\n",
1279 mmc
->f_max
, mmc
->f_min
, mmc
->max_busy_timeout
);
1281 /* host controller capabilities */
1282 mmc
->caps
|= MMC_CAP_SD_HIGHSPEED
| MMC_CAP_MMC_HIGHSPEED
|
1283 MMC_CAP_NEEDS_POLL
| MMC_CAP_HW_RESET
| MMC_CAP_ERASE
|
1286 spin_lock_init(&host
->lock
);
1287 mutex_init(&host
->mutex
);
1289 if (IS_ERR_OR_NULL(host
->dma_chan_rxtx
)) {
1290 dev_warn(dev
, "unable to initialise DMA channel. Falling back to PIO\n");
1291 host
->use_dma
= false;
1293 host
->use_dma
= true;
1295 host
->dma_cfg_tx
.src_addr_width
= DMA_SLAVE_BUSWIDTH_4_BYTES
;
1296 host
->dma_cfg_tx
.dst_addr_width
= DMA_SLAVE_BUSWIDTH_4_BYTES
;
1297 host
->dma_cfg_tx
.slave_id
= 13; /* DREQ channel */
1298 host
->dma_cfg_tx
.direction
= DMA_MEM_TO_DEV
;
1299 host
->dma_cfg_tx
.src_addr
= 0;
1300 host
->dma_cfg_tx
.dst_addr
= host
->phys_addr
+ SDDATA
;
1302 host
->dma_cfg_rx
.src_addr_width
= DMA_SLAVE_BUSWIDTH_4_BYTES
;
1303 host
->dma_cfg_rx
.dst_addr_width
= DMA_SLAVE_BUSWIDTH_4_BYTES
;
1304 host
->dma_cfg_rx
.slave_id
= 13; /* DREQ channel */
1305 host
->dma_cfg_rx
.direction
= DMA_DEV_TO_MEM
;
1306 host
->dma_cfg_rx
.src_addr
= host
->phys_addr
+ SDDATA
;
1307 host
->dma_cfg_rx
.dst_addr
= 0;
1309 if (dmaengine_slave_config(host
->dma_chan_rxtx
,
1310 &host
->dma_cfg_tx
) != 0 ||
1311 dmaengine_slave_config(host
->dma_chan_rxtx
,
1312 &host
->dma_cfg_rx
) != 0)
1313 host
->use_dma
= false;
1316 mmc
->max_segs
= 128;
1317 mmc
->max_req_size
= 524288;
1318 mmc
->max_seg_size
= mmc
->max_req_size
;
1319 mmc
->max_blk_size
= 1024;
1320 mmc
->max_blk_count
= 65535;
1322 /* report supported voltage ranges */
1323 mmc
->ocr_avail
= MMC_VDD_32_33
| MMC_VDD_33_34
;
1325 INIT_WORK(&host
->dma_work
, bcm2835_dma_complete_work
);
1326 INIT_DELAYED_WORK(&host
->timeout_work
, bcm2835_timeout
);
1328 /* Set interrupt enables */
1329 host
->hcfg
= SDHCFG_BUSY_IRPT_EN
;
1331 bcm2835_reset_internal(host
);
1333 ret
= request_threaded_irq(host
->irq
, bcm2835_irq
,
1334 bcm2835_threaded_irq
,
1335 0, mmc_hostname(mmc
), host
);
1337 dev_err(dev
, "failed to request IRQ %d: %d\n", host
->irq
, ret
);
1341 ret
= mmc_add_host(mmc
);
1343 free_irq(host
->irq
, host
);
1347 pio_limit_string
[0] = '\0';
1348 if (host
->use_dma
&& (PIO_THRESHOLD
> 0))
1349 sprintf(pio_limit_string
, " (>%d)", PIO_THRESHOLD
);
1350 dev_info(dev
, "loaded - DMA %s%s\n",
1351 host
->use_dma
? "enabled" : "disabled", pio_limit_string
);
1356 static int bcm2835_probe(struct platform_device
*pdev
)
1358 struct device
*dev
= &pdev
->dev
;
1360 struct resource
*iomem
;
1361 struct bcm2835_host
*host
;
1362 struct mmc_host
*mmc
;
1363 const __be32
*regaddr_p
;
1366 dev_dbg(dev
, "%s\n", __func__
);
1367 mmc
= mmc_alloc_host(sizeof(*host
), dev
);
1371 mmc
->ops
= &bcm2835_ops
;
1372 host
= mmc_priv(mmc
);
1375 spin_lock_init(&host
->lock
);
1377 iomem
= platform_get_resource(pdev
, IORESOURCE_MEM
, 0);
1378 host
->ioaddr
= devm_ioremap_resource(dev
, iomem
);
1379 if (IS_ERR(host
->ioaddr
)) {
1380 ret
= PTR_ERR(host
->ioaddr
);
1384 /* Parse OF address directly to get the physical address for
1385 * DMA to our registers.
1387 regaddr_p
= of_get_address(pdev
->dev
.of_node
, 0, NULL
, NULL
);
1389 dev_err(dev
, "Can't get phys address\n");
1394 host
->phys_addr
= be32_to_cpup(regaddr_p
);
1396 host
->dma_chan
= NULL
;
1397 host
->dma_desc
= NULL
;
1399 host
->dma_chan_rxtx
= dma_request_slave_channel(dev
, "rx-tx");
1401 clk
= devm_clk_get(dev
, NULL
);
1404 if (ret
!= -EPROBE_DEFER
)
1405 dev_err(dev
, "could not get clk: %d\n", ret
);
1409 host
->max_clk
= clk_get_rate(clk
);
1411 host
->irq
= platform_get_irq(pdev
, 0);
1412 if (host
->irq
<= 0) {
1413 dev_err(dev
, "get IRQ failed\n");
1418 ret
= mmc_of_parse(mmc
);
1422 ret
= bcm2835_add_host(host
);
1426 platform_set_drvdata(pdev
, host
);
1428 dev_dbg(dev
, "%s -> OK\n", __func__
);
1433 dev_dbg(dev
, "%s -> err %d\n", __func__
, ret
);
1439 static int bcm2835_remove(struct platform_device
*pdev
)
1441 struct bcm2835_host
*host
= platform_get_drvdata(pdev
);
1443 mmc_remove_host(host
->mmc
);
1445 writel(SDVDD_POWER_OFF
, host
->ioaddr
+ SDVDD
);
1447 free_irq(host
->irq
, host
);
1449 cancel_work_sync(&host
->dma_work
);
1450 cancel_delayed_work_sync(&host
->timeout_work
);
1452 if (host
->dma_chan_rxtx
)
1453 dma_release_channel(host
->dma_chan_rxtx
);
1455 mmc_free_host(host
->mmc
);
1456 platform_set_drvdata(pdev
, NULL
);
1461 static const struct of_device_id bcm2835_match
[] = {
1462 { .compatible
= "brcm,bcm2835-sdhost" },
1465 MODULE_DEVICE_TABLE(of
, bcm2835_match
);
1467 static struct platform_driver bcm2835_driver
= {
1468 .probe
= bcm2835_probe
,
1469 .remove
= bcm2835_remove
,
1471 .name
= "sdhost-bcm2835",
1472 .of_match_table
= bcm2835_match
,
1475 module_platform_driver(bcm2835_driver
);
1477 MODULE_ALIAS("platform:sdhost-bcm2835");
1478 MODULE_DESCRIPTION("BCM2835 SDHost driver");
1479 MODULE_LICENSE("GPL v2");
1480 MODULE_AUTHOR("Phil Elwell");