drivers/mtd/nand/Kconfig

   1 config MTD_NAND_ECC
   2         tristate
   3
   4 config MTD_NAND_ECC_SMC
   5         bool "NAND ECC Smart Media byte order"
   6         depends on MTD_NAND_ECC
   7         default n
   8         help
   9           Software ECC according to the Smart Media Specification.
  10           The original Linux implementation had byte 0 and 1 swapped.
  11
  12
  13 menuconfig MTD_NAND
  14         tristate "NAND Device Support"
  15         depends on MTD
  16         select MTD_NAND_IDS
  17         select MTD_NAND_ECC
  18         help
  19           This enables support for accessing all type of NAND flash
  20           devices. For further information see
  21           <http://www.linux-mtd.infradead.org/doc/nand.html>.
  22
  23 if MTD_NAND
  24
  25 config MTD_NAND_VERIFY_WRITE
  26         bool "Verify NAND page writes"
  27         help
  28           This adds an extra check when data is written to the flash. The
  29           NAND flash device internally checks only bits transitioning
  30           from 1 to 0. There is a rare possibility that even though the
  31           device thinks the write was successful, a bit could have been
  32           flipped accidentally due to device wear or something else.
  33
  34 config MTD_NAND_BCH
  35         tristate
  36         select BCH
  37         depends on MTD_NAND_ECC_BCH
  38         default MTD_NAND
  39
  40 config MTD_NAND_ECC_BCH
  41         bool "Support software BCH ECC"
  42         default n
  43         help
  44           This enables support for software BCH error correction. Binary BCH
  45           codes are more powerful and cpu intensive than traditional Hamming
  46           ECC codes. They are used with NAND devices requiring more than 1 bit
  47           of error correction.
  48
  49 config MTD_SM_COMMON
  50         tristate
  51         default n
  52
  53 config MTD_NAND_MUSEUM_IDS
  54         bool "Enable chip ids for obsolete ancient NAND devices"
  55         default n
  56         help
  57           Enable this option only when your board has first generation
  58           NAND chips (page size 256 byte, erase size 4-8KiB). The IDs
  59           of these chips were reused by later, larger chips.
  60
  61 config MTD_NAND_AUTCPU12
  62         tristate "SmartMediaCard on autronix autcpu12 board"
  63         depends on ARCH_AUTCPU12
  64         help
  65           This enables the driver for the autronix autcpu12 board to
  66           access the SmartMediaCard.
  67
  68 config MTD_NAND_DENALI
  69        depends on PCI
  70         tristate "Support Denali NAND controller on Intel Moorestown"
  71         help
  72           Enable the driver for NAND flash on Intel Moorestown, using the
  73           Denali NAND controller core.
  74
  75 config MTD_NAND_DENALI_SCRATCH_REG_ADDR
  76         hex "Denali NAND size scratch register address"
  77         default "0xFF108018"
  78         depends on MTD_NAND_DENALI
  79         help
  80           Some platforms place the NAND chip size in a scratch register
  81           because (some versions of) the driver aren't able to automatically
  82           determine the size of certain chips. Set the address of the
  83           scratch register here to enable this feature. On Intel Moorestown
  84           boards, the scratch register is at 0xFF108018.
  85
  86 config MTD_NAND_H1900
  87         tristate "iPAQ H1900 flash"
  88         depends on ARCH_PXA && BROKEN
  89         help
  90           This enables the driver for the iPAQ h1900 flash.
  91
  92 config MTD_NAND_GPIO
  93         tristate "GPIO NAND Flash driver"
  94         depends on GENERIC_GPIO && ARM
  95         help
  96           This enables a GPIO based NAND flash driver.
  97
  98 config MTD_NAND_SPIA
  99         tristate "NAND Flash device on SPIA board"
 100         depends on ARCH_P720T
 101         help
 102           If you had to ask, you don't have one. Say 'N'.
 103
 104 config MTD_NAND_AMS_DELTA
 105         tristate "NAND Flash device on Amstrad E3"
 106         depends on MACH_AMS_DELTA
 107         default y
 108         help
 109           Support for NAND flash on Amstrad E3 (Delta).
 110
 111 config MTD_NAND_OMAP2
 112         tristate "NAND Flash device on OMAP2, OMAP3 and OMAP4"
 113         depends on ARCH_OMAP2PLUS
 114         help
 115           Support for NAND flash on Texas Instruments OMAP2, OMAP3 and OMAP4
 116           platforms.
 117
 118 config MTD_NAND_OMAP_BCH
 119         depends on MTD_NAND && MTD_NAND_OMAP2 && ARCH_OMAP3
 120         bool "Enable support for hardware BCH error correction"
 121         default n
 122         select BCH
 123         select BCH_CONST_PARAMS
 124         help
 125          Support for hardware BCH error correction.
 126
 127 choice
 128         prompt "BCH error correction capability"
 129         depends on MTD_NAND_OMAP_BCH
 130
 131 config MTD_NAND_OMAP_BCH8
 132         bool "8 bits / 512 bytes (recommended)"
 133         help
 134          Support correcting up to 8 bitflips per 512-byte block.
 135          This will use 13 bytes of spare area per 512 bytes of page data.
 136          This is the recommended mode, as 4-bit mode does not work
 137          on some OMAP3 revisions, due to a hardware bug.
 138
 139 config MTD_NAND_OMAP_BCH4
 140         bool "4 bits / 512 bytes"
 141         help
 142          Support correcting up to 4 bitflips per 512-byte block.
 143          This will use 7 bytes of spare area per 512 bytes of page data.
 144          Note that this mode does not work on some OMAP3 revisions, due to a
 145          hardware bug. Please check your OMAP datasheet before selecting this
 146          mode.
 147
 148 endchoice
 149
 150 if MTD_NAND_OMAP_BCH
 151 config BCH_CONST_M
 152         default 13
 153 config BCH_CONST_T
 154         default 4 if MTD_NAND_OMAP_BCH4
 155         default 8 if MTD_NAND_OMAP_BCH8
 156 endif
 157
 158 config MTD_NAND_IDS
 159         tristate
 160
 161 config MTD_NAND_RICOH
 162         tristate "Ricoh xD card reader"
 163         default n
 164         depends on PCI
 165         select MTD_SM_COMMON
 166         help
 167           Enable support for Ricoh R5C852 xD card reader
 168           You also need to enable ether
 169           NAND SSFDC (SmartMedia) read only translation layer' or new
 170           expermental, readwrite
 171           'SmartMedia/xD new translation layer'
 172
 173 config MTD_NAND_AU1550
 174         tristate "Au1550/1200 NAND support"
 175         depends on MIPS_ALCHEMY
 176         help
 177           This enables the driver for the NAND flash controller on the
 178           AMD/Alchemy 1550 SOC.
 179
 180 config MTD_NAND_BF5XX
 181         tristate "Blackfin on-chip NAND Flash Controller driver"
 182         depends on BF54x || BF52x
 183         help
 184           This enables the Blackfin on-chip NAND flash controller
 185
 186           No board specific support is done by this driver, each board
 187           must advertise a platform_device for the driver to attach.
 188
 189           This driver can also be built as a module. If so, the module
 190           will be called bf5xx-nand.
 191
 192 config MTD_NAND_BF5XX_HWECC
 193         bool "BF5XX NAND Hardware ECC"
 194         default y
 195         depends on MTD_NAND_BF5XX
 196         help
 197           Enable the use of the BF5XX's internal ECC generator when
 198           using NAND.
 199
 200 config MTD_NAND_BF5XX_BOOTROM_ECC
 201         bool "Use Blackfin BootROM ECC Layout"
 202         default n
 203         depends on MTD_NAND_BF5XX_HWECC
 204         help
 205           If you wish to modify NAND pages and allow the Blackfin on-chip
 206           BootROM to boot from them, say Y here.  This is only necessary
 207           if you are booting U-Boot out of NAND and you wish to update
 208           U-Boot from Linux' userspace.  Otherwise, you should say N here.
 209
 210           If unsure, say N.
 211
 212 config MTD_NAND_RTC_FROM4
 213         tristate "Renesas Flash ROM 4-slot interface board (FROM_BOARD4)"
 214         depends on SH_SOLUTION_ENGINE
 215         select REED_SOLOMON
 216         select REED_SOLOMON_DEC8
 217         select BITREVERSE
 218         help
 219           This enables the driver for the Renesas Technology AG-AND
 220           flash interface board (FROM_BOARD4)
 221
 222 config MTD_NAND_PPCHAMELEONEVB
 223         tristate "NAND Flash device on PPChameleonEVB board"
 224         depends on PPCHAMELEONEVB && BROKEN
 225         help
 226           This enables the NAND flash driver on the PPChameleon EVB Board.
 227
 228 config MTD_NAND_S3C2410
 229         tristate "NAND Flash support for Samsung S3C SoCs"
 230         depends on ARCH_S3C24XX || ARCH_S3C64XX
 231         help
 232           This enables the NAND flash controller on the S3C24xx and S3C64xx
 233           SoCs
 234
 235           No board specific support is done by this driver, each board
 236           must advertise a platform_device for the driver to attach.
 237
 238 config MTD_NAND_S3C2410_DEBUG
 239         bool "Samsung S3C NAND driver debug"
 240         depends on MTD_NAND_S3C2410
 241         help
 242           Enable debugging of the S3C NAND driver
 243
 244 config MTD_NAND_S3C2410_HWECC
 245         bool "Samsung S3C NAND Hardware ECC"
 246         depends on MTD_NAND_S3C2410
 247         help
 248           Enable the use of the controller's internal ECC generator when
 249           using NAND. Early versions of the chips have had problems with
 250           incorrect ECC generation, and if using these, the default of
 251           software ECC is preferable.
 252
 253 config MTD_NAND_NDFC
 254         tristate "NDFC NanD Flash Controller"
 255         depends on 4xx
 256         select MTD_NAND_ECC_SMC
 257         help
 258          NDFC Nand Flash Controllers are integrated in IBM/AMCC's 4xx SoCs
 259
 260 config MTD_NAND_S3C2410_CLKSTOP
 261         bool "Samsung S3C NAND IDLE clock stop"
 262         depends on MTD_NAND_S3C2410
 263         default n
 264         help
 265           Stop the clock to the NAND controller when there is no chip
 266           selected to save power. This will mean there is a small delay
 267           when the is NAND chip selected or released, but will save
 268           approximately 5mA of power when there is nothing happening.
 269
 270 config MTD_NAND_BCM_UMI
 271         tristate "NAND Flash support for BCM Reference Boards"
 272         depends on ARCH_BCMRING
 273         help
 274           This enables the NAND flash controller on the BCM UMI block.
 275
 276           No board specific support is done by this driver, each board
 277           must advertise a platform_device for the driver to attach.
 278
 279 config MTD_NAND_BCM_UMI_HWCS
 280         bool "BCM UMI NAND Hardware CS"
 281         depends on MTD_NAND_BCM_UMI
 282         help
 283           Enable the use of the BCM UMI block's internal CS using NAND.
 284           This should only be used if you know the external NAND CS can toggle.
 285
 286 config MTD_NAND_DISKONCHIP
 287         tristate "DiskOnChip 2000, Millennium and Millennium Plus (NAND reimplementation) (EXPERIMENTAL)"
 288         depends on EXPERIMENTAL
 289         depends on HAS_IOMEM
 290         select REED_SOLOMON
 291         select REED_SOLOMON_DEC16
 292         help
 293           This is a reimplementation of M-Systems DiskOnChip 2000,
 294           Millennium and Millennium Plus as a standard NAND device driver,
 295           as opposed to the earlier self-contained MTD device drivers.
 296           This should enable, among other things, proper JFFS2 operation on
 297           these devices.
 298
 299 config MTD_NAND_DISKONCHIP_PROBE_ADVANCED
 300         bool "Advanced detection options for DiskOnChip"
 301         depends on MTD_NAND_DISKONCHIP
 302         help
 303           This option allows you to specify nonstandard address at which to
 304           probe for a DiskOnChip, or to change the detection options.  You
 305           are unlikely to need any of this unless you are using LinuxBIOS.
 306           Say 'N'.
 307
 308 config MTD_NAND_DISKONCHIP_PROBE_ADDRESS
 309         hex "Physical address of DiskOnChip" if MTD_NAND_DISKONCHIP_PROBE_ADVANCED
 310         depends on MTD_NAND_DISKONCHIP
 311         default "0"
 312         ---help---
 313         By default, the probe for DiskOnChip devices will look for a
 314         DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000.
 315         This option allows you to specify a single address at which to probe
 316         for the device, which is useful if you have other devices in that
 317         range which get upset when they are probed.
 318
 319         (Note that on PowerPC, the normal probe will only check at
 320         0xE4000000.)
 321
 322         Normally, you should leave this set to zero, to allow the probe at
 323         the normal addresses.
 324
 325 config MTD_NAND_DISKONCHIP_PROBE_HIGH
 326         bool "Probe high addresses"
 327         depends on MTD_NAND_DISKONCHIP_PROBE_ADVANCED
 328         help
 329           By default, the probe for DiskOnChip devices will look for a
 330           DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000.
 331           This option changes to make it probe between 0xFFFC8000 and
 332           0xFFFEE000.  Unless you are using LinuxBIOS, this is unlikely to be
 333           useful to you.  Say 'N'.
 334
 335 config MTD_NAND_DISKONCHIP_BBTWRITE
 336         bool "Allow BBT writes on DiskOnChip Millennium and 2000TSOP"
 337         depends on MTD_NAND_DISKONCHIP
 338         help
 339           On DiskOnChip devices shipped with the INFTL filesystem (Millennium
 340           and 2000 TSOP/Alon), Linux reserves some space at the end of the
 341           device for the Bad Block Table (BBT).  If you have existing INFTL
 342           data on your device (created by non-Linux tools such as M-Systems'
 343           DOS drivers), your data might overlap the area Linux wants to use for
 344           the BBT.  If this is a concern for you, leave this option disabled and
 345           Linux will not write BBT data into this area.
 346           The downside of leaving this option disabled is that if bad blocks
 347           are detected by Linux, they will not be recorded in the BBT, which
 348           could cause future problems.
 349           Once you enable this option, new filesystems (INFTL or others, created
 350           in Linux or other operating systems) will not use the reserved area.
 351           The only reason not to enable this option is to prevent damage to
 352           preexisting filesystems.
 353           Even if you leave this disabled, you can enable BBT writes at module
 354           load time (assuming you build diskonchip as a module) with the module
 355           parameter "inftl_bbt_write=1".
 356
 357 config MTD_NAND_DOCG4
 358         tristate "Support for DiskOnChip G4 (EXPERIMENTAL)"
 359         depends on EXPERIMENTAL
 360         select BCH
 361         select BITREVERSE
 362         help
 363           Support for diskonchip G4 nand flash, found in various smartphones and
 364           PDAs, among them the Palm Treo680, HTC Prophet and Wizard, Toshiba
 365           Portege G900, Asus P526, and O2 XDA Zinc.
 366
 367           With this driver you will be able to use UBI and create a ubifs on the
 368           device, so you may wish to consider enabling UBI and UBIFS as well.
 369
 370           These devices ship with the Mys/Sandisk SAFTL formatting, for which
 371           there is currently no mtd parser, so you may want to use command line
 372           partitioning to segregate write-protected blocks. On the Treo680, the
 373           first five erase blocks (256KiB each) are write-protected, followed
 374           by the block containing the saftl partition table.  This is probably
 375           typical.
 376
 377 config MTD_NAND_SHARPSL
 378         tristate "Support for NAND Flash on Sharp SL Series (C7xx + others)"
 379         depends on ARCH_PXA
 380
 381 config MTD_NAND_CAFE
 382         tristate "NAND support for OLPC CAFÉ chip"
 383         depends on PCI
 384         select REED_SOLOMON
 385         select REED_SOLOMON_DEC16
 386         help
 387           Use NAND flash attached to the CAFÉ chip designed for the OLPC
 388           laptop.
 389
 390 config MTD_NAND_CS553X
 391         tristate "NAND support for CS5535/CS5536 (AMD Geode companion chip)"
 392         depends on X86_32
 393         help
 394           The CS553x companion chips for the AMD Geode processor
 395           include NAND flash controllers with built-in hardware ECC
 396           capabilities; enabling this option will allow you to use
 397           these. The driver will check the MSRs to verify that the
 398           controller is enabled for NAND, and currently requires that
 399           the controller be in MMIO mode.
 400
 401           If you say "m", the module will be called cs553x_nand.
 402
 403 config MTD_NAND_ATMEL
 404         tristate "Support for NAND Flash / SmartMedia on AT91 and AVR32"
 405         depends on ARCH_AT91 || AVR32
 406         help
 407           Enables support for NAND Flash / Smart Media Card interface
 408           on Atmel AT91 and AVR32 processors.
 409
 410 config MTD_NAND_PXA3xx
 411         tristate "Support for NAND flash devices on PXA3xx"
 412         depends on PXA3xx || ARCH_MMP
 413         help
 414           This enables the driver for the NAND flash device found on
 415           PXA3xx processors
 416
 417 config MTD_NAND_SLC_LPC32XX
 418         tristate "NXP LPC32xx SLC Controller"
 419         depends on ARCH_LPC32XX
 420         help
 421           Enables support for NXP's LPC32XX SLC (i.e. for Single Level Cell
 422           chips) NAND controller. This is the default for the PHYTEC 3250
 423           reference board which contains a NAND256R3A2CZA6 chip.
 424
 425           Please check the actual NAND chip connected and its support
 426           by the SLC NAND controller.
 427
 428 config MTD_NAND_MLC_LPC32XX
 429         tristate "NXP LPC32xx MLC Controller"
 430         depends on ARCH_LPC32XX
 431         help
 432           Uses the LPC32XX MLC (i.e. for Multi Level Cell chips) NAND
 433           controller. This is the default for the WORK92105 controller
 434           board.
 435
 436           Please check the actual NAND chip connected and its support
 437           by the MLC NAND controller.
 438
 439 config MTD_NAND_CM_X270
 440         tristate "Support for NAND Flash on CM-X270 modules"
 441         depends on MACH_ARMCORE
 442
 443 config MTD_NAND_PASEMI
 444         tristate "NAND support for PA Semi PWRficient"
 445         depends on PPC_PASEMI
 446         help
 447           Enables support for NAND Flash interface on PA Semi PWRficient
 448           based boards
 449
 450 config MTD_NAND_TMIO
 451         tristate "NAND Flash device on Toshiba Mobile IO Controller"
 452         depends on MFD_TMIO
 453         help
 454           Support for NAND flash connected to a Toshiba Mobile IO
 455           Controller in some PDAs, including the Sharp SL6000x.
 456
 457 config MTD_NAND_NANDSIM
 458         tristate "Support for NAND Flash Simulator"
 459         help
 460           The simulator may simulate various NAND flash chips for the
 461           MTD nand layer.
 462
 463 config MTD_NAND_GPMI_NAND
 464         bool "GPMI NAND Flash Controller driver"
 465         depends on MTD_NAND && MXS_DMA
 466         help
 467          Enables NAND Flash support for IMX23 or IMX28.
 468          The GPMI controller is very powerful, with the help of BCH
 469          module, it can do the hardware ECC. The GPMI supports several
 470          NAND flashs at the same time. The GPMI may conflicts with other
 471          block, such as SD card. So pay attention to it when you enable
 472          the GPMI.
 473
 474 config MTD_NAND_PLATFORM
 475         tristate "Support for generic platform NAND driver"
 476         depends on HAS_IOMEM
 477         help
 478           This implements a generic NAND driver for on-SOC platform
 479           devices. You will need to provide platform-specific functions
 480           via platform_data.
 481
 482 config MTD_ALAUDA
 483         tristate "MTD driver for Olympus MAUSB-10 and Fujifilm DPC-R1"
 484         depends on USB
 485         help
 486           These two (and possibly other) Alauda-based cardreaders for
 487           SmartMedia and xD allow raw flash access.
 488
 489 config MTD_NAND_ORION
 490         tristate "NAND Flash support for Marvell Orion SoC"
 491         depends on PLAT_ORION
 492         help
 493           This enables the NAND flash controller on Orion machines.
 494
 495           No board specific support is done by this driver, each board
 496           must advertise a platform_device for the driver to attach.
 497
 498 config MTD_NAND_FSL_ELBC
 499         tristate "NAND support for Freescale eLBC controllers"
 500         depends on PPC_OF
 501         select FSL_LBC
 502         help
 503           Various Freescale chips, including the 8313, include a NAND Flash
 504           Controller Module with built-in hardware ECC capabilities.
 505           Enabling this option will enable you to use this to control
 506           external NAND devices.
 507
 508 config MTD_NAND_FSL_IFC
 509         tristate "NAND support for Freescale IFC controller"
 510         depends on MTD_NAND && FSL_SOC
 511         select FSL_IFC
 512         help
 513           Various Freescale chips e.g P1010, include a NAND Flash machine
 514           with built-in hardware ECC capabilities.
 515           Enabling this option will enable you to use this to control
 516           external NAND devices.
 517
 518 config MTD_NAND_FSL_UPM
 519         tristate "Support for NAND on Freescale UPM"
 520         depends on PPC_83xx || PPC_85xx
 521         select FSL_LBC
 522         help
 523           Enables support for NAND Flash chips wired onto Freescale PowerPC
 524           processor localbus with User-Programmable Machine support.
 525
 526 config MTD_NAND_MPC5121_NFC
 527         tristate "MPC5121 built-in NAND Flash Controller support"
 528         depends on PPC_MPC512x
 529         help
 530           This enables the driver for the NAND flash controller on the
 531           MPC5121 SoC.
 532
 533 config MTD_NAND_MXC
 534         tristate "MXC NAND support"
 535         depends on ARCH_MXC
 536         help
 537           This enables the driver for the NAND flash controller on the
 538           MXC processors.
 539
 540 config MTD_NAND_NOMADIK
 541         tristate "ST Nomadik 8815 NAND support"
 542         depends on ARCH_NOMADIK
 543         help
 544           Driver for the NAND flash controller on the Nomadik, with ECC.
 545
 546 config MTD_NAND_SH_FLCTL
 547         tristate "Support for NAND on Renesas SuperH FLCTL"
 548         depends on SUPERH || ARCH_SHMOBILE
 549         help
 550           Several Renesas SuperH CPU has FLCTL. This option enables support
 551           for NAND Flash using FLCTL.
 552
 553 config MTD_NAND_DAVINCI
 554         tristate "Support NAND on DaVinci SoC"
 555         depends on ARCH_DAVINCI
 556         help
 557           Enable the driver for NAND flash chips on Texas Instruments
 558           DaVinci processors.
 559
 560 config MTD_NAND_TXX9NDFMC
 561         tristate "NAND Flash support for TXx9 SoC"
 562         depends on SOC_TX4938 || SOC_TX4939
 563         help
 564           This enables the NAND flash controller on the TXx9 SoCs.
 565
 566 config MTD_NAND_SOCRATES
 567         tristate "Support for NAND on Socrates board"
 568         depends on SOCRATES
 569         help
 570           Enables support for NAND Flash chips wired onto Socrates board.
 571
 572 config MTD_NAND_NUC900
 573         tristate "Support for NAND on Nuvoton NUC9xx/w90p910 evaluation boards."
 574         depends on ARCH_W90X900
 575         help
 576           This enables the driver for the NAND Flash on evaluation board based
 577           on w90p910 / NUC9xx.
 578
 579 config MTD_NAND_JZ4740
 580         tristate "Support for JZ4740 SoC NAND controller"
 581         depends on MACH_JZ4740
 582         help
 583                 Enables support for NAND Flash on JZ4740 SoC based boards.
 584
 585 config MTD_NAND_FSMC
 586         tristate "Support for NAND on ST Micros FSMC"
 587         depends on PLAT_SPEAR || PLAT_NOMADIK || MACH_U300
 588         help
 589           Enables support for NAND Flash chips on the ST Microelectronics
 590           Flexible Static Memory Controller (FSMC)
 591
 592 endif # MTD_NAND