]> git.proxmox.com Git - mirror_ubuntu-bionic-kernel.git/blob - drivers/net/bnx2x/bnx2x_link.c
projects / mirror_ubuntu-bionic-kernel.git / blob
? search:


db5913da552731ef45fe64edc4bb88ee9edea4d2
[mirror_ubuntu-bionic-kernel.git] / drivers / net / bnx2x / bnx2x_link.c
1 /* Copyright 2008-2011 Broadcom Corporation
2 *
3 * Unless you and Broadcom execute a separate written software license
4 * agreement governing use of this software, this software is licensed to you
5 * under the terms of the GNU General Public License version 2, available
6 * at http://www.gnu.org/licenses/old-licenses/gpl-2.0.html (the "GPL").
7 *
8 * Notwithstanding the above, under no circumstances may you combine this
9 * software in any way with any other Broadcom software provided under a
10 * license other than the GPL, without Broadcom's express prior written
11 * consent.
12 *
13 * Written by Yaniv Rosner
14 *
15 */
16
17 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
18
19 #include <linux/kernel.h>
20 #include <linux/errno.h>
21 #include <linux/pci.h>
22 #include <linux/netdevice.h>
23 #include <linux/delay.h>
24 #include <linux/ethtool.h>
25 #include <linux/mutex.h>
26
27 #include "bnx2x.h"
28 #include "bnx2x_cmn.h"
29
30
31 /********************************************************/
32 #define ETH_HLEN 14
33 /* L2 header size + 2*VLANs (8 bytes) + LLC SNAP (8 bytes) */
34 #define ETH_OVREHEAD (ETH_HLEN + 8 + 8)
35 #define ETH_MIN_PACKET_SIZE 60
36 #define ETH_MAX_PACKET_SIZE 1500
37 #define ETH_MAX_JUMBO_PACKET_SIZE 9600
38 #define MDIO_ACCESS_TIMEOUT 1000
39 #define BMAC_CONTROL_RX_ENABLE 2
40 #define WC_LANE_MAX 4
41 #define I2C_SWITCH_WIDTH 2
42 #define I2C_BSC0 0
43 #define I2C_BSC1 1
44 #define I2C_WA_RETRY_CNT 3
45 #define MCPR_IMC_COMMAND_READ_OP 1
46 #define MCPR_IMC_COMMAND_WRITE_OP 2
47
48 /***********************************************************/
49 /* Shortcut definitions */
50 /***********************************************************/
51
52 #define NIG_LATCH_BC_ENABLE_MI_INT 0
53
54 #define NIG_STATUS_EMAC0_MI_INT \
55 NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_EMAC0_MISC_MI_INT
56 #define NIG_STATUS_XGXS0_LINK10G \
57 NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_XGXS0_LINK10G
58 #define NIG_STATUS_XGXS0_LINK_STATUS \
59 NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_XGXS0_LINK_STATUS
60 #define NIG_STATUS_XGXS0_LINK_STATUS_SIZE \
61 NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_XGXS0_LINK_STATUS_SIZE
62 #define NIG_STATUS_SERDES0_LINK_STATUS \
63 NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_SERDES0_LINK_STATUS
64 #define NIG_MASK_MI_INT \
65 NIG_MASK_INTERRUPT_PORT0_REG_MASK_EMAC0_MISC_MI_INT
66 #define NIG_MASK_XGXS0_LINK10G \
67 NIG_MASK_INTERRUPT_PORT0_REG_MASK_XGXS0_LINK10G
68 #define NIG_MASK_XGXS0_LINK_STATUS \
69 NIG_MASK_INTERRUPT_PORT0_REG_MASK_XGXS0_LINK_STATUS
70 #define NIG_MASK_SERDES0_LINK_STATUS \
71 NIG_MASK_INTERRUPT_PORT0_REG_MASK_SERDES0_LINK_STATUS
72
73 #define MDIO_AN_CL73_OR_37_COMPLETE \
74 (MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_AUTONEG_COMPLETE | \
75 MDIO_GP_STATUS_TOP_AN_STATUS1_CL37_AUTONEG_COMPLETE)
76
77 #define XGXS_RESET_BITS \
78 (MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_RSTB_HW | \
79 MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_IDDQ | \
80 MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_PWRDWN | \
81 MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_PWRDWN_SD | \
82 MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_TXD_FIFO_RSTB)
83
84 #define SERDES_RESET_BITS \
85 (MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_SERDES0_RSTB_HW | \
86 MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_SERDES0_IDDQ | \
87 MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_SERDES0_PWRDWN | \
88 MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_SERDES0_PWRDWN_SD)
89
90 #define AUTONEG_CL37 SHARED_HW_CFG_AN_ENABLE_CL37
91 #define AUTONEG_CL73 SHARED_HW_CFG_AN_ENABLE_CL73
92 #define AUTONEG_BAM SHARED_HW_CFG_AN_ENABLE_BAM
93 #define AUTONEG_PARALLEL \
94 SHARED_HW_CFG_AN_ENABLE_PARALLEL_DETECTION
95 #define AUTONEG_SGMII_FIBER_AUTODET \
96 SHARED_HW_CFG_AN_EN_SGMII_FIBER_AUTO_DETECT
97 #define AUTONEG_REMOTE_PHY SHARED_HW_CFG_AN_ENABLE_REMOTE_PHY
98
99 #define GP_STATUS_PAUSE_RSOLUTION_TXSIDE \
100 MDIO_GP_STATUS_TOP_AN_STATUS1_PAUSE_RSOLUTION_TXSIDE
101 #define GP_STATUS_PAUSE_RSOLUTION_RXSIDE \
102 MDIO_GP_STATUS_TOP_AN_STATUS1_PAUSE_RSOLUTION_RXSIDE
103 #define GP_STATUS_SPEED_MASK \
104 MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_MASK
105 #define GP_STATUS_10M MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10M
106 #define GP_STATUS_100M MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_100M
107 #define GP_STATUS_1G MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_1G
108 #define GP_STATUS_2_5G MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_2_5G
109 #define GP_STATUS_5G MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_5G
110 #define GP_STATUS_6G MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_6G
111 #define GP_STATUS_10G_HIG \
112 MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_HIG
113 #define GP_STATUS_10G_CX4 \
114 MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_CX4
115 #define GP_STATUS_1G_KX MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_1G_KX
116 #define GP_STATUS_10G_KX4 \
117 MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_KX4
118 #define GP_STATUS_10G_KR MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_KR
119 #define GP_STATUS_10G_XFI MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_XFI
120 #define GP_STATUS_20G_DXGXS MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_20G_DXGXS
121 #define GP_STATUS_10G_SFI MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_SFI
122 #define LINK_10THD LINK_STATUS_SPEED_AND_DUPLEX_10THD
123 #define LINK_10TFD LINK_STATUS_SPEED_AND_DUPLEX_10TFD
124 #define LINK_100TXHD LINK_STATUS_SPEED_AND_DUPLEX_100TXHD
125 #define LINK_100T4 LINK_STATUS_SPEED_AND_DUPLEX_100T4
126 #define LINK_100TXFD LINK_STATUS_SPEED_AND_DUPLEX_100TXFD
127 #define LINK_1000THD LINK_STATUS_SPEED_AND_DUPLEX_1000THD
128 #define LINK_1000TFD LINK_STATUS_SPEED_AND_DUPLEX_1000TFD
129 #define LINK_1000XFD LINK_STATUS_SPEED_AND_DUPLEX_1000XFD
130 #define LINK_2500THD LINK_STATUS_SPEED_AND_DUPLEX_2500THD
131 #define LINK_2500TFD LINK_STATUS_SPEED_AND_DUPLEX_2500TFD
132 #define LINK_2500XFD LINK_STATUS_SPEED_AND_DUPLEX_2500XFD
133 #define LINK_10GTFD LINK_STATUS_SPEED_AND_DUPLEX_10GTFD
134 #define LINK_10GXFD LINK_STATUS_SPEED_AND_DUPLEX_10GXFD
135 #define LINK_20GTFD LINK_STATUS_SPEED_AND_DUPLEX_20GTFD
136 #define LINK_20GXFD LINK_STATUS_SPEED_AND_DUPLEX_20GXFD
137
138
139
140 /* */
141 #define SFP_EEPROM_CON_TYPE_ADDR 0x2
142 #define SFP_EEPROM_CON_TYPE_VAL_LC 0x7
143 #define SFP_EEPROM_CON_TYPE_VAL_COPPER 0x21
144
145
146 #define SFP_EEPROM_COMP_CODE_ADDR 0x3
147 #define SFP_EEPROM_COMP_CODE_SR_MASK (1<<4)
148 #define SFP_EEPROM_COMP_CODE_LR_MASK (1<<5)
149 #define SFP_EEPROM_COMP_CODE_LRM_MASK (1<<6)
150
151 #define SFP_EEPROM_FC_TX_TECH_ADDR 0x8
152 #define SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_PASSIVE 0x4
153 #define SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_ACTIVE 0x8
154
155 #define SFP_EEPROM_OPTIONS_ADDR 0x40
156 #define SFP_EEPROM_OPTIONS_LINEAR_RX_OUT_MASK 0x1
157 #define SFP_EEPROM_OPTIONS_SIZE 2
158
159 #define EDC_MODE_LINEAR 0x0022
160 #define EDC_MODE_LIMITING 0x0044
161 #define EDC_MODE_PASSIVE_DAC 0x0055
162
163
164 /* BRB thresholds for E2*/
165 #define PFC_E2_BRB_MAC_PAUSE_XOFF_THR_PAUSE 170
166 #define PFC_E2_BRB_MAC_PAUSE_XOFF_THR_NON_PAUSE 0
167
168 #define PFC_E2_BRB_MAC_PAUSE_XON_THR_PAUSE 250
169 #define PFC_E2_BRB_MAC_PAUSE_XON_THR_NON_PAUSE 0
170
171 #define PFC_E2_BRB_MAC_FULL_XOFF_THR_PAUSE 10
172 #define PFC_E2_BRB_MAC_FULL_XOFF_THR_NON_PAUSE 90
173
174 #define PFC_E2_BRB_MAC_FULL_XON_THR_PAUSE 50
175 #define PFC_E2_BRB_MAC_FULL_XON_THR_NON_PAUSE 250
176
177 /* BRB thresholds for E3A0 */
178 #define PFC_E3A0_BRB_MAC_PAUSE_XOFF_THR_PAUSE 290
179 #define PFC_E3A0_BRB_MAC_PAUSE_XOFF_THR_NON_PAUSE 0
180
181 #define PFC_E3A0_BRB_MAC_PAUSE_XON_THR_PAUSE 410
182 #define PFC_E3A0_BRB_MAC_PAUSE_XON_THR_NON_PAUSE 0
183
184 #define PFC_E3A0_BRB_MAC_FULL_XOFF_THR_PAUSE 10
185 #define PFC_E3A0_BRB_MAC_FULL_XOFF_THR_NON_PAUSE 170
186
187 #define PFC_E3A0_BRB_MAC_FULL_XON_THR_PAUSE 50
188 #define PFC_E3A0_BRB_MAC_FULL_XON_THR_NON_PAUSE 410
189
190
191 /* BRB thresholds for E3B0 2 port mode*/
192 #define PFC_E3B0_2P_BRB_MAC_PAUSE_XOFF_THR_PAUSE 1025
193 #define PFC_E3B0_2P_BRB_MAC_PAUSE_XOFF_THR_NON_PAUSE 0
194
195 #define PFC_E3B0_2P_BRB_MAC_PAUSE_XON_THR_PAUSE 1025
196 #define PFC_E3B0_2P_BRB_MAC_PAUSE_XON_THR_NON_PAUSE 0
197
198 #define PFC_E3B0_2P_BRB_MAC_FULL_XOFF_THR_PAUSE 10
199 #define PFC_E3B0_2P_BRB_MAC_FULL_XOFF_THR_NON_PAUSE 1025
200
201 #define PFC_E3B0_2P_BRB_MAC_FULL_XON_THR_PAUSE 50
202 #define PFC_E3B0_2P_BRB_MAC_FULL_XON_THR_NON_PAUSE 1025
203
204 /* only for E3B0*/
205 #define PFC_E3B0_2P_BRB_FULL_LB_XOFF_THR 1025
206 #define PFC_E3B0_2P_BRB_FULL_LB_XON_THR 1025
207
208 /* Lossy +Lossless GUARANTIED == GUART */
209 #define PFC_E3B0_2P_MIX_PAUSE_LB_GUART 284
210 /* Lossless +Lossless*/
211 #define PFC_E3B0_2P_PAUSE_LB_GUART 236
212 /* Lossy +Lossy*/
213 #define PFC_E3B0_2P_NON_PAUSE_LB_GUART 342
214
215 /* Lossy +Lossless*/
216 #define PFC_E3B0_2P_MIX_PAUSE_MAC_0_CLASS_T_GUART 284
217 /* Lossless +Lossless*/
218 #define PFC_E3B0_2P_PAUSE_MAC_0_CLASS_T_GUART 236
219 /* Lossy +Lossy*/
220 #define PFC_E3B0_2P_NON_PAUSE_MAC_0_CLASS_T_GUART 336
221 #define PFC_E3B0_2P_BRB_MAC_0_CLASS_T_GUART_HYST 80
222
223 #define PFC_E3B0_2P_BRB_MAC_1_CLASS_T_GUART 0
224 #define PFC_E3B0_2P_BRB_MAC_1_CLASS_T_GUART_HYST 0
225
226 /* BRB thresholds for E3B0 4 port mode */
227 #define PFC_E3B0_4P_BRB_MAC_PAUSE_XOFF_THR_PAUSE 304
228 #define PFC_E3B0_4P_BRB_MAC_PAUSE_XOFF_THR_NON_PAUSE 0
229
230 #define PFC_E3B0_4P_BRB_MAC_PAUSE_XON_THR_PAUSE 384
231 #define PFC_E3B0_4P_BRB_MAC_PAUSE_XON_THR_NON_PAUSE 0
232
233 #define PFC_E3B0_4P_BRB_MAC_FULL_XOFF_THR_PAUSE 10
234 #define PFC_E3B0_4P_BRB_MAC_FULL_XOFF_THR_NON_PAUSE 304
235
236 #define PFC_E3B0_4P_BRB_MAC_FULL_XON_THR_PAUSE 50
237 #define PFC_E3B0_4P_BRB_MAC_FULL_XON_THR_NON_PAUSE 384
238
239
240 /* only for E3B0*/
241 #define PFC_E3B0_4P_BRB_FULL_LB_XOFF_THR 304
242 #define PFC_E3B0_4P_BRB_FULL_LB_XON_THR 384
243 #define PFC_E3B0_4P_LB_GUART 120
244
245 #define PFC_E3B0_4P_BRB_MAC_0_CLASS_T_GUART 120
246 #define PFC_E3B0_4P_BRB_MAC_0_CLASS_T_GUART_HYST 80
247
248 #define PFC_E3B0_4P_BRB_MAC_1_CLASS_T_GUART 80
249 #define PFC_E3B0_4P_BRB_MAC_1_CLASS_T_GUART_HYST 120
250
251 #define DCBX_INVALID_COS (0xFF)
252
253 #define ETS_BW_LIMIT_CREDIT_UPPER_BOUND (0x5000)
254 #define ETS_BW_LIMIT_CREDIT_WEIGHT (0x5000)
255 #define ETS_E3B0_NIG_MIN_W_VAL_UP_TO_10GBPS (1360)
256 #define ETS_E3B0_NIG_MIN_W_VAL_20GBPS (2720)
257 #define ETS_E3B0_PBF_MIN_W_VAL (10000)
258
259 #define MAX_PACKET_SIZE (9700)
260 #define WC_UC_TIMEOUT 100
261
262 /**********************************************************/
263 /* INTERFACE */
264 /**********************************************************/
265
266 #define CL22_WR_OVER_CL45(_bp, _phy, _bank, _addr, _val) \
267 bnx2x_cl45_write(_bp, _phy, \
268 (_phy)->def_md_devad, \
269 (_bank + (_addr & 0xf)), \
270 _val)
271
272 #define CL22_RD_OVER_CL45(_bp, _phy, _bank, _addr, _val) \
273 bnx2x_cl45_read(_bp, _phy, \
274 (_phy)->def_md_devad, \
275 (_bank + (_addr & 0xf)), \
276 _val)
277
278 static u32 bnx2x_bits_en(struct bnx2x *bp, u32 reg, u32 bits)
279 {
280 u32 val = REG_RD(bp, reg);
281
282 val |= bits;
283 REG_WR(bp, reg, val);
284 return val;
285 }
286
287 static u32 bnx2x_bits_dis(struct bnx2x *bp, u32 reg, u32 bits)
288 {
289 u32 val = REG_RD(bp, reg);
290
291 val &= ~bits;
292 REG_WR(bp, reg, val);
293 return val;
294 }
295
296 /******************************************************************/
297 /* EPIO/GPIO section */
298 /******************************************************************/
299 static void bnx2x_get_epio(struct bnx2x *bp, u32 epio_pin, u32 *en)
300 {
301 u32 epio_mask, gp_oenable;
302 *en = 0;
303 /* Sanity check */
304 if (epio_pin > 31) {
305 DP(NETIF_MSG_LINK, "Invalid EPIO pin %d to get\n", epio_pin);
306 return;
307 }
308
309 epio_mask = 1 << epio_pin;
310 /* Set this EPIO to output */
311 gp_oenable = REG_RD(bp, MCP_REG_MCPR_GP_OENABLE);
312 REG_WR(bp, MCP_REG_MCPR_GP_OENABLE, gp_oenable & ~epio_mask);
313
314 *en = (REG_RD(bp, MCP_REG_MCPR_GP_INPUTS) & epio_mask) >> epio_pin;
315 }
316 static void bnx2x_set_epio(struct bnx2x *bp, u32 epio_pin, u32 en)
317 {
318 u32 epio_mask, gp_output, gp_oenable;
319
320 /* Sanity check */
321 if (epio_pin > 31) {
322 DP(NETIF_MSG_LINK, "Invalid EPIO pin %d to set\n", epio_pin);
323 return;
324 }
325 DP(NETIF_MSG_LINK, "Setting EPIO pin %d to %d\n", epio_pin, en);
326 epio_mask = 1 << epio_pin;
327 /* Set this EPIO to output */
328 gp_output = REG_RD(bp, MCP_REG_MCPR_GP_OUTPUTS);
329 if (en)
330 gp_output |= epio_mask;
331 else
332 gp_output &= ~epio_mask;
333
334 REG_WR(bp, MCP_REG_MCPR_GP_OUTPUTS, gp_output);
335
336 /* Set the value for this EPIO */
337 gp_oenable = REG_RD(bp, MCP_REG_MCPR_GP_OENABLE);
338 REG_WR(bp, MCP_REG_MCPR_GP_OENABLE, gp_oenable | epio_mask);
339 }
340
341 static void bnx2x_set_cfg_pin(struct bnx2x *bp, u32 pin_cfg, u32 val)
342 {
343 if (pin_cfg == PIN_CFG_NA)
344 return;
345 if (pin_cfg >= PIN_CFG_EPIO0) {
346 bnx2x_set_epio(bp, pin_cfg - PIN_CFG_EPIO0, val);
347 } else {
348 u8 gpio_num = (pin_cfg - PIN_CFG_GPIO0_P0) & 0x3;
349 u8 gpio_port = (pin_cfg - PIN_CFG_GPIO0_P0) >> 2;
350 bnx2x_set_gpio(bp, gpio_num, (u8)val, gpio_port);
351 }
352 }
353
354 static u32 bnx2x_get_cfg_pin(struct bnx2x *bp, u32 pin_cfg, u32 *val)
355 {
356 if (pin_cfg == PIN_CFG_NA)
357 return -EINVAL;
358 if (pin_cfg >= PIN_CFG_EPIO0) {
359 bnx2x_get_epio(bp, pin_cfg - PIN_CFG_EPIO0, val);
360 } else {
361 u8 gpio_num = (pin_cfg - PIN_CFG_GPIO0_P0) & 0x3;
362 u8 gpio_port = (pin_cfg - PIN_CFG_GPIO0_P0) >> 2;
363 *val = bnx2x_get_gpio(bp, gpio_num, gpio_port);
364 }
365 return 0;
366
367 }
368 /******************************************************************/
369 /* ETS section */
370 /******************************************************************/
371 static void bnx2x_ets_e2e3a0_disabled(struct link_params *params)
372 {
373 /* ETS disabled configuration*/
374 struct bnx2x *bp = params->bp;
375
376 DP(NETIF_MSG_LINK, "ETS E2E3 disabled configuration\n");
377
378 /*
379 * mapping between entry priority to client number (0,1,2 -debug and
380 * management clients, 3 - COS0 client, 4 - COS client)(HIGHEST)
381 * 3bits client num.
382 * PRI4 | PRI3 | PRI2 | PRI1 | PRI0
383 * cos1-100 cos0-011 dbg1-010 dbg0-001 MCP-000
384 */
385
386 REG_WR(bp, NIG_REG_P0_TX_ARB_PRIORITY_CLIENT, 0x4688);
387 /*
388 * Bitmap of 5bits length. Each bit specifies whether the entry behaves
389 * as strict. Bits 0,1,2 - debug and management entries, 3 -
390 * COS0 entry, 4 - COS1 entry.
391 * COS1 | COS0 | DEBUG1 | DEBUG0 | MGMT
392 * bit4 bit3 bit2 bit1 bit0
393 * MCP and debug are strict
394 */
395
396 REG_WR(bp, NIG_REG_P0_TX_ARB_CLIENT_IS_STRICT, 0x7);
397 /* defines which entries (clients) are subjected to WFQ arbitration */
398 REG_WR(bp, NIG_REG_P0_TX_ARB_CLIENT_IS_SUBJECT2WFQ, 0);
399 /*
400 * For strict priority entries defines the number of consecutive
401 * slots for the highest priority.
402 */
403 REG_WR(bp, NIG_REG_P0_TX_ARB_NUM_STRICT_ARB_SLOTS, 0x100);
404 /*
405 * mapping between the CREDIT_WEIGHT registers and actual client
406 * numbers
407 */
408 REG_WR(bp, NIG_REG_P0_TX_ARB_CLIENT_CREDIT_MAP, 0);
409 REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_0, 0);
410 REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_1, 0);
411
412 REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_0, 0);
413 REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_1, 0);
414 REG_WR(bp, PBF_REG_HIGH_PRIORITY_COS_NUM, 0);
415 /* ETS mode disable */
416 REG_WR(bp, PBF_REG_ETS_ENABLED, 0);
417 /*
418 * If ETS mode is enabled (there is no strict priority) defines a WFQ
419 * weight for COS0/COS1.
420 */
421 REG_WR(bp, PBF_REG_COS0_WEIGHT, 0x2710);
422 REG_WR(bp, PBF_REG_COS1_WEIGHT, 0x2710);
423 /* Upper bound that COS0_WEIGHT can reach in the WFQ arbiter */
424 REG_WR(bp, PBF_REG_COS0_UPPER_BOUND, 0x989680);
425 REG_WR(bp, PBF_REG_COS1_UPPER_BOUND, 0x989680);
426 /* Defines the number of consecutive slots for the strict priority */
427 REG_WR(bp, PBF_REG_NUM_STRICT_ARB_SLOTS, 0);
428 }
429 /******************************************************************************
430 * Description:
431 * Getting min_w_val will be set according to line speed .
432 *.
433 ******************************************************************************/
434 static u32 bnx2x_ets_get_min_w_val_nig(const struct link_vars *vars)
435 {
436 u32 min_w_val = 0;
437 /* Calculate min_w_val.*/
438 if (vars->link_up) {
439 if (SPEED_20000 == vars->line_speed)
440 min_w_val = ETS_E3B0_NIG_MIN_W_VAL_20GBPS;
441 else
442 min_w_val = ETS_E3B0_NIG_MIN_W_VAL_UP_TO_10GBPS;
443 } else
444 min_w_val = ETS_E3B0_NIG_MIN_W_VAL_20GBPS;
445 /**
446 * If the link isn't up (static configuration for example ) The
447 * link will be according to 20GBPS.
448 */
449 return min_w_val;
450 }
451 /******************************************************************************
452 * Description:
453 * Getting credit upper bound form min_w_val.
454 *.
455 ******************************************************************************/
456 static u32 bnx2x_ets_get_credit_upper_bound(const u32 min_w_val)
457 {
458 const u32 credit_upper_bound = (u32)MAXVAL((150 * min_w_val),
459 MAX_PACKET_SIZE);
460 return credit_upper_bound;
461 }
462 /******************************************************************************
463 * Description:
464 * Set credit upper bound for NIG.
465 *.
466 ******************************************************************************/
467 static void bnx2x_ets_e3b0_set_credit_upper_bound_nig(
468 const struct link_params *params,
469 const u32 min_w_val)
470 {
471 struct bnx2x *bp = params->bp;
472 const u8 port = params->port;
473 const u32 credit_upper_bound =
474 bnx2x_ets_get_credit_upper_bound(min_w_val);
475
476 REG_WR(bp, (port) ? NIG_REG_P1_TX_ARB_CREDIT_UPPER_BOUND_0 :
477 NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_0, credit_upper_bound);
478 REG_WR(bp, (port) ? NIG_REG_P1_TX_ARB_CREDIT_UPPER_BOUND_1 :
479 NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_1, credit_upper_bound);
480 REG_WR(bp, (port) ? NIG_REG_P1_TX_ARB_CREDIT_UPPER_BOUND_2 :
481 NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_2, credit_upper_bound);
482 REG_WR(bp, (port) ? NIG_REG_P1_TX_ARB_CREDIT_UPPER_BOUND_3 :
483 NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_3, credit_upper_bound);
484 REG_WR(bp, (port) ? NIG_REG_P1_TX_ARB_CREDIT_UPPER_BOUND_4 :
485 NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_4, credit_upper_bound);
486 REG_WR(bp, (port) ? NIG_REG_P1_TX_ARB_CREDIT_UPPER_BOUND_5 :
487 NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_5, credit_upper_bound);
488
489 if (0 == port) {
490 REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_6,
491 credit_upper_bound);
492 REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_7,
493 credit_upper_bound);
494 REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_8,
495 credit_upper_bound);
496 }
497 }
498 /******************************************************************************
499 * Description:
500 * Will return the NIG ETS registers to init values.Except
501 * credit_upper_bound.
502 * That isn't used in this configuration (No WFQ is enabled) and will be
503 * configured acording to spec
504 *.
505 ******************************************************************************/
506 static void bnx2x_ets_e3b0_nig_disabled(const struct link_params *params,
507 const struct link_vars *vars)
508 {
509 struct bnx2x *bp = params->bp;
510 const u8 port = params->port;
511 const u32 min_w_val = bnx2x_ets_get_min_w_val_nig(vars);
512 /**
513 * mapping between entry priority to client number (0,1,2 -debug and
514 * management clients, 3 - COS0 client, 4 - COS1, ... 8 -
515 * COS5)(HIGHEST) 4bits client num.TODO_ETS - Should be done by
516 * reset value or init tool
517 */
518 if (port) {
519 REG_WR(bp, NIG_REG_P1_TX_ARB_PRIORITY_CLIENT2_LSB, 0x543210);
520 REG_WR(bp, NIG_REG_P1_TX_ARB_PRIORITY_CLIENT2_MSB, 0x0);
521 } else {
522 REG_WR(bp, NIG_REG_P0_TX_ARB_PRIORITY_CLIENT2_LSB, 0x76543210);
523 REG_WR(bp, NIG_REG_P0_TX_ARB_PRIORITY_CLIENT2_MSB, 0x8);
524 }
525 /**
526 * For strict priority entries defines the number of consecutive
527 * slots for the highest priority.
528 */
529 /* TODO_ETS - Should be done by reset value or init tool */
530 REG_WR(bp, (port) ? NIG_REG_P1_TX_ARB_NUM_STRICT_ARB_SLOTS :
531 NIG_REG_P1_TX_ARB_NUM_STRICT_ARB_SLOTS, 0x100);
532 /**
533 * mapping between the CREDIT_WEIGHT registers and actual client
534 * numbers
535 */
536 /* TODO_ETS - Should be done by reset value or init tool */
537 if (port) {
538 /*Port 1 has 6 COS*/
539 REG_WR(bp, NIG_REG_P1_TX_ARB_CLIENT_CREDIT_MAP2_LSB, 0x210543);
540 REG_WR(bp, NIG_REG_P1_TX_ARB_CLIENT_CREDIT_MAP2_MSB, 0x0);
541 } else {
542 /*Port 0 has 9 COS*/
543 REG_WR(bp, NIG_REG_P0_TX_ARB_CLIENT_CREDIT_MAP2_LSB,
544 0x43210876);
545 REG_WR(bp, NIG_REG_P0_TX_ARB_CLIENT_CREDIT_MAP2_MSB, 0x5);
546 }
547
548 /**
549 * Bitmap of 5bits length. Each bit specifies whether the entry behaves
550 * as strict. Bits 0,1,2 - debug and management entries, 3 -
551 * COS0 entry, 4 - COS1 entry.
552 * COS1 | COS0 | DEBUG1 | DEBUG0 | MGMT
553 * bit4 bit3 bit2 bit1 bit0
554 * MCP and debug are strict
555 */
556 if (port)
557 REG_WR(bp, NIG_REG_P1_TX_ARB_CLIENT_IS_STRICT, 0x3f);
558 else
559 REG_WR(bp, NIG_REG_P0_TX_ARB_CLIENT_IS_STRICT, 0x1ff);
560 /* defines which entries (clients) are subjected to WFQ arbitration */
561 REG_WR(bp, (port) ? NIG_REG_P1_TX_ARB_CLIENT_IS_SUBJECT2WFQ :
562 NIG_REG_P0_TX_ARB_CLIENT_IS_SUBJECT2WFQ, 0);
563
564 /**
565 * Please notice the register address are note continuous and a
566 * for here is note appropriate.In 2 port mode port0 only COS0-5
567 * can be used. DEBUG1,DEBUG1,MGMT are never used for WFQ* In 4
568 * port mode port1 only COS0-2 can be used. DEBUG1,DEBUG1,MGMT
569 * are never used for WFQ
570 */
571 REG_WR(bp, (port) ? NIG_REG_P1_TX_ARB_CREDIT_WEIGHT_0 :
572 NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_0, 0x0);
573 REG_WR(bp, (port) ? NIG_REG_P1_TX_ARB_CREDIT_WEIGHT_1 :
574 NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_1, 0x0);
575 REG_WR(bp, (port) ? NIG_REG_P1_TX_ARB_CREDIT_WEIGHT_2 :
576 NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_2, 0x0);
577 REG_WR(bp, (port) ? NIG_REG_P1_TX_ARB_CREDIT_WEIGHT_3 :
578 NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_3, 0x0);
579 REG_WR(bp, (port) ? NIG_REG_P1_TX_ARB_CREDIT_WEIGHT_4 :
580 NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_4, 0x0);
581 REG_WR(bp, (port) ? NIG_REG_P1_TX_ARB_CREDIT_WEIGHT_5 :
582 NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_5, 0x0);
583 if (0 == port) {
584 REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_6, 0x0);
585 REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_7, 0x0);
586 REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_8, 0x0);
587 }
588
589 bnx2x_ets_e3b0_set_credit_upper_bound_nig(params, min_w_val);
590 }
591 /******************************************************************************
592 * Description:
593 * Set credit upper bound for PBF.
594 *.
595 ******************************************************************************/
596 static void bnx2x_ets_e3b0_set_credit_upper_bound_pbf(
597 const struct link_params *params,
598 const u32 min_w_val)
599 {
600 struct bnx2x *bp = params->bp;
601 const u32 credit_upper_bound =
602 bnx2x_ets_get_credit_upper_bound(min_w_val);
603 const u8 port = params->port;
604 u32 base_upper_bound = 0;
605 u8 max_cos = 0;
606 u8 i = 0;
607 /**
608 * In 2 port mode port0 has COS0-5 that can be used for WFQ.In 4
609 * port mode port1 has COS0-2 that can be used for WFQ.
610 */
611 if (0 == port) {
612 base_upper_bound = PBF_REG_COS0_UPPER_BOUND_P0;
613 max_cos = DCBX_E3B0_MAX_NUM_COS_PORT0;
614 } else {
615 base_upper_bound = PBF_REG_COS0_UPPER_BOUND_P1;
616 max_cos = DCBX_E3B0_MAX_NUM_COS_PORT1;
617 }
618
619 for (i = 0; i < max_cos; i++)
620 REG_WR(bp, base_upper_bound + (i << 2), credit_upper_bound);
621 }
622
623 /******************************************************************************
624 * Description:
625 * Will return the PBF ETS registers to init values.Except
626 * credit_upper_bound.
627 * That isn't used in this configuration (No WFQ is enabled) and will be
628 * configured acording to spec
629 *.
630 ******************************************************************************/
631 static void bnx2x_ets_e3b0_pbf_disabled(const struct link_params *params)
632 {
633 struct bnx2x *bp = params->bp;
634 const u8 port = params->port;
635 const u32 min_w_val_pbf = ETS_E3B0_PBF_MIN_W_VAL;
636 u8 i = 0;
637 u32 base_weight = 0;
638 u8 max_cos = 0;
639
640 /**
641 * mapping between entry priority to client number 0 - COS0
642 * client, 2 - COS1, ... 5 - COS5)(HIGHEST) 4bits client num.
643 * TODO_ETS - Should be done by reset value or init tool
644 */
645 if (port)
646 /* 0x688 (|011|0 10|00 1|000) */
647 REG_WR(bp, PBF_REG_ETS_ARB_PRIORITY_CLIENT_P1 , 0x688);
648 else
649 /* (10 1|100 |011|0 10|00 1|000) */
650 REG_WR(bp, PBF_REG_ETS_ARB_PRIORITY_CLIENT_P0 , 0x2C688);
651
652 /* TODO_ETS - Should be done by reset value or init tool */
653 if (port)
654 /* 0x688 (|011|0 10|00 1|000)*/
655 REG_WR(bp, PBF_REG_ETS_ARB_CLIENT_CREDIT_MAP_P1, 0x688);
656 else
657 /* 0x2C688 (10 1|100 |011|0 10|00 1|000) */
658 REG_WR(bp, PBF_REG_ETS_ARB_CLIENT_CREDIT_MAP_P0, 0x2C688);
659
660 REG_WR(bp, (port) ? PBF_REG_ETS_ARB_NUM_STRICT_ARB_SLOTS_P1 :
661 PBF_REG_ETS_ARB_NUM_STRICT_ARB_SLOTS_P0 , 0x100);
662
663
664 REG_WR(bp, (port) ? PBF_REG_ETS_ARB_CLIENT_IS_STRICT_P1 :
665 PBF_REG_ETS_ARB_CLIENT_IS_STRICT_P0 , 0);
666
667 REG_WR(bp, (port) ? PBF_REG_ETS_ARB_CLIENT_IS_SUBJECT2WFQ_P1 :
668 PBF_REG_ETS_ARB_CLIENT_IS_SUBJECT2WFQ_P0 , 0);
669 /**
670 * In 2 port mode port0 has COS0-5 that can be used for WFQ.
671 * In 4 port mode port1 has COS0-2 that can be used for WFQ.
672 */
673 if (0 == port) {
674 base_weight = PBF_REG_COS0_WEIGHT_P0;
675 max_cos = DCBX_E3B0_MAX_NUM_COS_PORT0;
676 } else {
677 base_weight = PBF_REG_COS0_WEIGHT_P1;
678 max_cos = DCBX_E3B0_MAX_NUM_COS_PORT1;
679 }
680
681 for (i = 0; i < max_cos; i++)
682 REG_WR(bp, base_weight + (0x4 * i), 0);
683
684 bnx2x_ets_e3b0_set_credit_upper_bound_pbf(params, min_w_val_pbf);
685 }
686 /******************************************************************************
687 * Description:
688 * E3B0 disable will return basicly the values to init values.
689 *.
690 ******************************************************************************/
691 static int bnx2x_ets_e3b0_disabled(const struct link_params *params,
692 const struct link_vars *vars)
693 {
694 struct bnx2x *bp = params->bp;
695
696 if (!CHIP_IS_E3B0(bp)) {
697 DP(NETIF_MSG_LINK, "bnx2x_ets_e3b0_disabled the chip isn't E3B0"
698 "\n");
699 return -EINVAL;
700 }
701
702 bnx2x_ets_e3b0_nig_disabled(params, vars);
703
704 bnx2x_ets_e3b0_pbf_disabled(params);
705
706 return 0;
707 }
708
709 /******************************************************************************
710 * Description:
711 * Disable will return basicly the values to init values.
712 *.
713 ******************************************************************************/
714 int bnx2x_ets_disabled(struct link_params *params,
715 struct link_vars *vars)
716 {
717 struct bnx2x *bp = params->bp;
718 int bnx2x_status = 0;
719
720 if ((CHIP_IS_E2(bp)) || (CHIP_IS_E3A0(bp)))
721 bnx2x_ets_e2e3a0_disabled(params);
722 else if (CHIP_IS_E3B0(bp))
723 bnx2x_status = bnx2x_ets_e3b0_disabled(params, vars);
724 else {
725 DP(NETIF_MSG_LINK, "bnx2x_ets_disabled - chip not supported\n");
726 return -EINVAL;
727 }
728
729 return bnx2x_status;
730 }
731
732 /******************************************************************************
733 * Description
734 * Set the COS mappimg to SP and BW until this point all the COS are not
735 * set as SP or BW.
736 ******************************************************************************/
737 static int bnx2x_ets_e3b0_cli_map(const struct link_params *params,
738 const struct bnx2x_ets_params *ets_params,
739 const u8 cos_sp_bitmap,
740 const u8 cos_bw_bitmap)
741 {
742 struct bnx2x *bp = params->bp;
743 const u8 port = params->port;
744 const u8 nig_cli_sp_bitmap = 0x7 | (cos_sp_bitmap << 3);
745 const u8 pbf_cli_sp_bitmap = cos_sp_bitmap;
746 const u8 nig_cli_subject2wfq_bitmap = cos_bw_bitmap << 3;
747 const u8 pbf_cli_subject2wfq_bitmap = cos_bw_bitmap;
748
749 REG_WR(bp, (port) ? NIG_REG_P1_TX_ARB_CLIENT_IS_STRICT :
750 NIG_REG_P0_TX_ARB_CLIENT_IS_STRICT, nig_cli_sp_bitmap);
751
752 REG_WR(bp, (port) ? PBF_REG_ETS_ARB_CLIENT_IS_STRICT_P1 :
753 PBF_REG_ETS_ARB_CLIENT_IS_STRICT_P0 , pbf_cli_sp_bitmap);
754
755 REG_WR(bp, (port) ? NIG_REG_P1_TX_ARB_CLIENT_IS_SUBJECT2WFQ :
756 NIG_REG_P0_TX_ARB_CLIENT_IS_SUBJECT2WFQ,
757 nig_cli_subject2wfq_bitmap);
758
759 REG_WR(bp, (port) ? PBF_REG_ETS_ARB_CLIENT_IS_SUBJECT2WFQ_P1 :
760 PBF_REG_ETS_ARB_CLIENT_IS_SUBJECT2WFQ_P0,
761 pbf_cli_subject2wfq_bitmap);
762
763 return 0;
764 }
765
766 /******************************************************************************
767 * Description:
768 * This function is needed because NIG ARB_CREDIT_WEIGHT_X are
769 * not continues and ARB_CREDIT_WEIGHT_0 + offset is suitable.
770 ******************************************************************************/
771 static int bnx2x_ets_e3b0_set_cos_bw(struct bnx2x *bp,
772 const u8 cos_entry,
773 const u32 min_w_val_nig,
774 const u32 min_w_val_pbf,
775 const u16 total_bw,
776 const u8 bw,
777 const u8 port)
778 {
779 u32 nig_reg_adress_crd_weight = 0;
780 u32 pbf_reg_adress_crd_weight = 0;
781 /* Calculate and set BW for this COS - use 1 instead of 0 for BW */
782 const u32 cos_bw_nig = ((bw ? bw : 1) * min_w_val_nig) / total_bw;
783 const u32 cos_bw_pbf = ((bw ? bw : 1) * min_w_val_pbf) / total_bw;
784
785 switch (cos_entry) {
786 case 0:
787 nig_reg_adress_crd_weight =
788 (port) ? NIG_REG_P1_TX_ARB_CREDIT_WEIGHT_0 :
789 NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_0;
790 pbf_reg_adress_crd_weight = (port) ?
791 PBF_REG_COS0_WEIGHT_P1 : PBF_REG_COS0_WEIGHT_P0;
792 break;
793 case 1:
794 nig_reg_adress_crd_weight = (port) ?
795 NIG_REG_P1_TX_ARB_CREDIT_WEIGHT_1 :
796 NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_1;
797 pbf_reg_adress_crd_weight = (port) ?
798 PBF_REG_COS1_WEIGHT_P1 : PBF_REG_COS1_WEIGHT_P0;
799 break;
800 case 2:
801 nig_reg_adress_crd_weight = (port) ?
802 NIG_REG_P1_TX_ARB_CREDIT_WEIGHT_2 :
803 NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_2;
804
805 pbf_reg_adress_crd_weight = (port) ?
806 PBF_REG_COS2_WEIGHT_P1 : PBF_REG_COS2_WEIGHT_P0;
807 break;
808 case 3:
809 if (port)
810 return -EINVAL;
811 nig_reg_adress_crd_weight =
812 NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_3;
813 pbf_reg_adress_crd_weight =
814 PBF_REG_COS3_WEIGHT_P0;
815 break;
816 case 4:
817 if (port)
818 return -EINVAL;
819 nig_reg_adress_crd_weight =
820 NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_4;
821 pbf_reg_adress_crd_weight = PBF_REG_COS4_WEIGHT_P0;
822 break;
823 case 5:
824 if (port)
825 return -EINVAL;
826 nig_reg_adress_crd_weight =
827 NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_5;
828 pbf_reg_adress_crd_weight = PBF_REG_COS5_WEIGHT_P0;
829 break;
830 }
831
832 REG_WR(bp, nig_reg_adress_crd_weight, cos_bw_nig);
833
834 REG_WR(bp, pbf_reg_adress_crd_weight, cos_bw_pbf);
835
836 return 0;
837 }
838 /******************************************************************************
839 * Description:
840 * Calculate the total BW.A value of 0 isn't legal.
841 *.
842 ******************************************************************************/
843 static int bnx2x_ets_e3b0_get_total_bw(
844 const struct link_params *params,
845 const struct bnx2x_ets_params *ets_params,
846 u16 *total_bw)
847 {
848 struct bnx2x *bp = params->bp;
849 u8 cos_idx = 0;
850
851 *total_bw = 0 ;
852 /* Calculate total BW requested */
853 for (cos_idx = 0; cos_idx < ets_params->num_of_cos; cos_idx++) {
854 if (bnx2x_cos_state_bw == ets_params->cos[cos_idx].state) {
855 *total_bw +=
856 ets_params->cos[cos_idx].params.bw_params.bw;
857 }
858 }
859
860 /* Check total BW is valid */
861 if ((100 != *total_bw) || (0 == *total_bw)) {
862 if (0 == *total_bw) {
863 DP(NETIF_MSG_LINK, "bnx2x_ets_E3B0_config toatl BW"
864 "shouldn't be 0\n");
865 return -EINVAL;
866 }
867 DP(NETIF_MSG_LINK, "bnx2x_ets_E3B0_config toatl BW should be"
868 "100\n");
869 /**
870 * We can handle a case whre the BW isn't 100 this can happen
871 * if the TC are joined.
872 */
873 }
874 return 0;
875 }
876
877 /******************************************************************************
878 * Description:
879 * Invalidate all the sp_pri_to_cos.
880 *.
881 ******************************************************************************/
882 static void bnx2x_ets_e3b0_sp_pri_to_cos_init(u8 *sp_pri_to_cos)
883 {
884 u8 pri = 0;
885 for (pri = 0; pri < DCBX_MAX_NUM_COS; pri++)
886 sp_pri_to_cos[pri] = DCBX_INVALID_COS;
887 }
888 /******************************************************************************
889 * Description:
890 * Calculate and set the SP (ARB_PRIORITY_CLIENT) NIG and PBF registers
891 * according to sp_pri_to_cos.
892 *.
893 ******************************************************************************/
894 static int bnx2x_ets_e3b0_sp_pri_to_cos_set(const struct link_params *params,
895 u8 *sp_pri_to_cos, const u8 pri,
896 const u8 cos_entry)
897 {
898 struct bnx2x *bp = params->bp;
899 const u8 port = params->port;
900 const u8 max_num_of_cos = (port) ? DCBX_E3B0_MAX_NUM_COS_PORT1 :
901 DCBX_E3B0_MAX_NUM_COS_PORT0;
902
903 if (DCBX_INVALID_COS != sp_pri_to_cos[pri]) {
904 DP(NETIF_MSG_LINK, "bnx2x_ets_e3b0_sp_pri_to_cos_set invalid "
905 "parameter There can't be two COS's with"
906 "the same strict pri\n");
907 return -EINVAL;
908 }
909
910 if (pri > max_num_of_cos) {
911 DP(NETIF_MSG_LINK, "bnx2x_ets_e3b0_sp_pri_to_cos_set invalid"
912 "parameter Illegal strict priority\n");
913 return -EINVAL;
914 }
915
916 sp_pri_to_cos[pri] = cos_entry;
917 return 0;
918
919 }
920
921 /******************************************************************************
922 * Description:
923 * Returns the correct value according to COS and priority in
924 * the sp_pri_cli register.
925 *.
926 ******************************************************************************/
927 static u64 bnx2x_e3b0_sp_get_pri_cli_reg(const u8 cos, const u8 cos_offset,
928 const u8 pri_set,
929 const u8 pri_offset,
930 const u8 entry_size)
931 {
932 u64 pri_cli_nig = 0;
933 pri_cli_nig = ((u64)(cos + cos_offset)) << (entry_size *
934 (pri_set + pri_offset));
935
936 return pri_cli_nig;
937 }
938 /******************************************************************************
939 * Description:
940 * Returns the correct value according to COS and priority in the
941 * sp_pri_cli register for NIG.
942 *.
943 ******************************************************************************/
944 static u64 bnx2x_e3b0_sp_get_pri_cli_reg_nig(const u8 cos, const u8 pri_set)
945 {
946 /* MCP Dbg0 and dbg1 are always with higher strict pri*/
947 const u8 nig_cos_offset = 3;
948 const u8 nig_pri_offset = 3;
949
950 return bnx2x_e3b0_sp_get_pri_cli_reg(cos, nig_cos_offset, pri_set,
951 nig_pri_offset, 4);
952
953 }
954 /******************************************************************************
955 * Description:
956 * Returns the correct value according to COS and priority in the
957 * sp_pri_cli register for PBF.
958 *.
959 ******************************************************************************/
960 static u64 bnx2x_e3b0_sp_get_pri_cli_reg_pbf(const u8 cos, const u8 pri_set)
961 {
962 const u8 pbf_cos_offset = 0;
963 const u8 pbf_pri_offset = 0;
964
965 return bnx2x_e3b0_sp_get_pri_cli_reg(cos, pbf_cos_offset, pri_set,
966 pbf_pri_offset, 3);
967
968 }
969
970 /******************************************************************************
971 * Description:
972 * Calculate and set the SP (ARB_PRIORITY_CLIENT) NIG and PBF registers
973 * according to sp_pri_to_cos.(which COS has higher priority)
974 *.
975 ******************************************************************************/
976 static int bnx2x_ets_e3b0_sp_set_pri_cli_reg(const struct link_params *params,
977 u8 *sp_pri_to_cos)
978 {
979 struct bnx2x *bp = params->bp;
980 u8 i = 0;
981 const u8 port = params->port;
982 /* MCP Dbg0 and dbg1 are always with higher strict pri*/
983 u64 pri_cli_nig = 0x210;
984 u32 pri_cli_pbf = 0x0;
985 u8 pri_set = 0;
986 u8 pri_bitmask = 0;
987 const u8 max_num_of_cos = (port) ? DCBX_E3B0_MAX_NUM_COS_PORT1 :
988 DCBX_E3B0_MAX_NUM_COS_PORT0;
989
990 u8 cos_bit_to_set = (1 << max_num_of_cos) - 1;
991
992 /* Set all the strict priority first */
993 for (i = 0; i < max_num_of_cos; i++) {
994 if (DCBX_INVALID_COS != sp_pri_to_cos[i]) {
995 if (DCBX_MAX_NUM_COS <= sp_pri_to_cos[i]) {
996 DP(NETIF_MSG_LINK,
997 "bnx2x_ets_e3b0_sp_set_pri_cli_reg "
998 "invalid cos entry\n");
999 return -EINVAL;
1000 }
1001
1002 pri_cli_nig |= bnx2x_e3b0_sp_get_pri_cli_reg_nig(
1003 sp_pri_to_cos[i], pri_set);
1004
1005 pri_cli_pbf |= bnx2x_e3b0_sp_get_pri_cli_reg_pbf(
1006 sp_pri_to_cos[i], pri_set);
1007 pri_bitmask = 1 << sp_pri_to_cos[i];
1008 /* COS is used remove it from bitmap.*/
1009 if (0 == (pri_bitmask & cos_bit_to_set)) {
1010 DP(NETIF_MSG_LINK,
1011 "bnx2x_ets_e3b0_sp_set_pri_cli_reg "
1012 "invalid There can't be two COS's with"
1013 " the same strict pri\n");
1014 return -EINVAL;
1015 }
1016 cos_bit_to_set &= ~pri_bitmask;
1017 pri_set++;
1018 }
1019 }
1020
1021 /* Set all the Non strict priority i= COS*/
1022 for (i = 0; i < max_num_of_cos; i++) {
1023 pri_bitmask = 1 << i;
1024 /* Check if COS was already used for SP */
1025 if (pri_bitmask & cos_bit_to_set) {
1026 /* COS wasn't used for SP */
1027 pri_cli_nig |= bnx2x_e3b0_sp_get_pri_cli_reg_nig(
1028 i, pri_set);
1029
1030 pri_cli_pbf |= bnx2x_e3b0_sp_get_pri_cli_reg_pbf(
1031 i, pri_set);
1032 /* COS is used remove it from bitmap.*/
1033 cos_bit_to_set &= ~pri_bitmask;
1034 pri_set++;
1035 }
1036 }
1037
1038 if (pri_set != max_num_of_cos) {
1039 DP(NETIF_MSG_LINK, "bnx2x_ets_e3b0_sp_set_pri_cli_reg not all "
1040 "entries were set\n");
1041 return -EINVAL;
1042 }
1043
1044 if (port) {
1045 /* Only 6 usable clients*/
1046 REG_WR(bp, NIG_REG_P1_TX_ARB_PRIORITY_CLIENT2_LSB,
1047 (u32)pri_cli_nig);
1048
1049 REG_WR(bp, PBF_REG_ETS_ARB_PRIORITY_CLIENT_P1 , pri_cli_pbf);
1050 } else {
1051 /* Only 9 usable clients*/
1052 const u32 pri_cli_nig_lsb = (u32) (pri_cli_nig);
1053 const u32 pri_cli_nig_msb = (u32) ((pri_cli_nig >> 32) & 0xF);
1054
1055 REG_WR(bp, NIG_REG_P0_TX_ARB_PRIORITY_CLIENT2_LSB,
1056 pri_cli_nig_lsb);
1057 REG_WR(bp, NIG_REG_P0_TX_ARB_PRIORITY_CLIENT2_MSB,
1058 pri_cli_nig_msb);
1059
1060 REG_WR(bp, PBF_REG_ETS_ARB_PRIORITY_CLIENT_P0 , pri_cli_pbf);
1061 }
1062 return 0;
1063 }
1064
1065 /******************************************************************************
1066 * Description:
1067 * Configure the COS to ETS according to BW and SP settings.
1068 ******************************************************************************/
1069 int bnx2x_ets_e3b0_config(const struct link_params *params,
1070 const struct link_vars *vars,
1071 const struct bnx2x_ets_params *ets_params)
1072 {
1073 struct bnx2x *bp = params->bp;
1074 int bnx2x_status = 0;
1075 const u8 port = params->port;
1076 u16 total_bw = 0;
1077 const u32 min_w_val_nig = bnx2x_ets_get_min_w_val_nig(vars);
1078 const u32 min_w_val_pbf = ETS_E3B0_PBF_MIN_W_VAL;
1079 u8 cos_bw_bitmap = 0;
1080 u8 cos_sp_bitmap = 0;
1081 u8 sp_pri_to_cos[DCBX_MAX_NUM_COS] = {0};
1082 const u8 max_num_of_cos = (port) ? DCBX_E3B0_MAX_NUM_COS_PORT1 :
1083 DCBX_E3B0_MAX_NUM_COS_PORT0;
1084 u8 cos_entry = 0;
1085
1086 if (!CHIP_IS_E3B0(bp)) {
1087 DP(NETIF_MSG_LINK, "bnx2x_ets_e3b0_disabled the chip isn't E3B0"
1088 "\n");
1089 return -EINVAL;
1090 }
1091
1092 if ((ets_params->num_of_cos > max_num_of_cos)) {
1093 DP(NETIF_MSG_LINK, "bnx2x_ets_E3B0_config the number of COS "
1094 "isn't supported\n");
1095 return -EINVAL;
1096 }
1097
1098 /* Prepare sp strict priority parameters*/
1099 bnx2x_ets_e3b0_sp_pri_to_cos_init(sp_pri_to_cos);
1100
1101 /* Prepare BW parameters*/
1102 bnx2x_status = bnx2x_ets_e3b0_get_total_bw(params, ets_params,
1103 &total_bw);
1104 if (0 != bnx2x_status) {
1105 DP(NETIF_MSG_LINK, "bnx2x_ets_E3B0_config get_total_bw failed "
1106 "\n");
1107 return -EINVAL;
1108 }
1109
1110 /**
1111 * Upper bound is set according to current link speed (min_w_val
1112 * should be the same for upper bound and COS credit val).
1113 */
1114 bnx2x_ets_e3b0_set_credit_upper_bound_nig(params, min_w_val_nig);
1115 bnx2x_ets_e3b0_set_credit_upper_bound_pbf(params, min_w_val_pbf);
1116
1117
1118 for (cos_entry = 0; cos_entry < ets_params->num_of_cos; cos_entry++) {
1119 if (bnx2x_cos_state_bw == ets_params->cos[cos_entry].state) {
1120 cos_bw_bitmap |= (1 << cos_entry);
1121 /**
1122 * The function also sets the BW in HW(not the mappin
1123 * yet)
1124 */
1125 bnx2x_status = bnx2x_ets_e3b0_set_cos_bw(
1126 bp, cos_entry, min_w_val_nig, min_w_val_pbf,
1127 total_bw,
1128 ets_params->cos[cos_entry].params.bw_params.bw,
1129 port);
1130 } else if (bnx2x_cos_state_strict ==
1131 ets_params->cos[cos_entry].state){
1132 cos_sp_bitmap |= (1 << cos_entry);
1133
1134 bnx2x_status = bnx2x_ets_e3b0_sp_pri_to_cos_set(
1135 params,
1136 sp_pri_to_cos,
1137 ets_params->cos[cos_entry].params.sp_params.pri,
1138 cos_entry);
1139
1140 } else {
1141 DP(NETIF_MSG_LINK, "bnx2x_ets_e3b0_config cos state not"
1142 " valid\n");
1143 return -EINVAL;
1144 }
1145 if (0 != bnx2x_status) {
1146 DP(NETIF_MSG_LINK, "bnx2x_ets_e3b0_config set cos bw "
1147 "failed\n");
1148 return bnx2x_status;
1149 }
1150 }
1151
1152 /* Set SP register (which COS has higher priority) */
1153 bnx2x_status = bnx2x_ets_e3b0_sp_set_pri_cli_reg(params,
1154 sp_pri_to_cos);
1155
1156 if (0 != bnx2x_status) {
1157 DP(NETIF_MSG_LINK, "bnx2x_ets_E3B0_config set_pri_cli_reg "
1158 "failed\n");
1159 return bnx2x_status;
1160 }
1161
1162 /* Set client mapping of BW and strict */
1163 bnx2x_status = bnx2x_ets_e3b0_cli_map(params, ets_params,
1164 cos_sp_bitmap,
1165 cos_bw_bitmap);
1166
1167 if (0 != bnx2x_status) {
1168 DP(NETIF_MSG_LINK, "bnx2x_ets_E3B0_config SP failed\n");
1169 return bnx2x_status;
1170 }
1171 return 0;
1172 }
1173 static void bnx2x_ets_bw_limit_common(const struct link_params *params)
1174 {
1175 /* ETS disabled configuration */
1176 struct bnx2x *bp = params->bp;
1177 DP(NETIF_MSG_LINK, "ETS enabled BW limit configuration\n");
1178 /*
1179 * defines which entries (clients) are subjected to WFQ arbitration
1180 * COS0 0x8
1181 * COS1 0x10
1182 */
1183 REG_WR(bp, NIG_REG_P0_TX_ARB_CLIENT_IS_SUBJECT2WFQ, 0x18);
1184 /*
1185 * mapping between the ARB_CREDIT_WEIGHT registers and actual
1186 * client numbers (WEIGHT_0 does not actually have to represent
1187 * client 0)
1188 * PRI4 | PRI3 | PRI2 | PRI1 | PRI0
1189 * cos1-001 cos0-000 dbg1-100 dbg0-011 MCP-010
1190 */
1191 REG_WR(bp, NIG_REG_P0_TX_ARB_CLIENT_CREDIT_MAP, 0x111A);
1192
1193 REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_0,
1194 ETS_BW_LIMIT_CREDIT_UPPER_BOUND);
1195 REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_1,
1196 ETS_BW_LIMIT_CREDIT_UPPER_BOUND);
1197
1198 /* ETS mode enabled*/
1199 REG_WR(bp, PBF_REG_ETS_ENABLED, 1);
1200
1201 /* Defines the number of consecutive slots for the strict priority */
1202 REG_WR(bp, PBF_REG_NUM_STRICT_ARB_SLOTS, 0);
1203 /*
1204 * Bitmap of 5bits length. Each bit specifies whether the entry behaves
1205 * as strict. Bits 0,1,2 - debug and management entries, 3 - COS0
1206 * entry, 4 - COS1 entry.
1207 * COS1 | COS0 | DEBUG21 | DEBUG0 | MGMT
1208 * bit4 bit3 bit2 bit1 bit0
1209 * MCP and debug are strict
1210 */
1211 REG_WR(bp, NIG_REG_P0_TX_ARB_CLIENT_IS_STRICT, 0x7);
1212
1213 /* Upper bound that COS0_WEIGHT can reach in the WFQ arbiter.*/
1214 REG_WR(bp, PBF_REG_COS0_UPPER_BOUND,
1215 ETS_BW_LIMIT_CREDIT_UPPER_BOUND);
1216 REG_WR(bp, PBF_REG_COS1_UPPER_BOUND,
1217 ETS_BW_LIMIT_CREDIT_UPPER_BOUND);
1218 }
1219
1220 void bnx2x_ets_bw_limit(const struct link_params *params, const u32 cos0_bw,
1221 const u32 cos1_bw)
1222 {
1223 /* ETS disabled configuration*/
1224 struct bnx2x *bp = params->bp;
1225 const u32 total_bw = cos0_bw + cos1_bw;
1226 u32 cos0_credit_weight = 0;
1227 u32 cos1_credit_weight = 0;
1228
1229 DP(NETIF_MSG_LINK, "ETS enabled BW limit configuration\n");
1230
1231 if ((0 == total_bw) ||
1232 (0 == cos0_bw) ||
1233 (0 == cos1_bw)) {
1234 DP(NETIF_MSG_LINK, "Total BW can't be zero\n");
1235 return;
1236 }
1237
1238 cos0_credit_weight = (cos0_bw * ETS_BW_LIMIT_CREDIT_WEIGHT)/
1239 total_bw;
1240 cos1_credit_weight = (cos1_bw * ETS_BW_LIMIT_CREDIT_WEIGHT)/
1241 total_bw;
1242
1243 bnx2x_ets_bw_limit_common(params);
1244
1245 REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_0, cos0_credit_weight);
1246 REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_1, cos1_credit_weight);
1247
1248 REG_WR(bp, PBF_REG_COS0_WEIGHT, cos0_credit_weight);
1249 REG_WR(bp, PBF_REG_COS1_WEIGHT, cos1_credit_weight);
1250 }
1251
1252 int bnx2x_ets_strict(const struct link_params *params, const u8 strict_cos)
1253 {
1254 /* ETS disabled configuration*/
1255 struct bnx2x *bp = params->bp;
1256 u32 val = 0;
1257
1258 DP(NETIF_MSG_LINK, "ETS enabled strict configuration\n");
1259 /*
1260 * Bitmap of 5bits length. Each bit specifies whether the entry behaves
1261 * as strict. Bits 0,1,2 - debug and management entries,
1262 * 3 - COS0 entry, 4 - COS1 entry.
1263 * COS1 | COS0 | DEBUG21 | DEBUG0 | MGMT
1264 * bit4 bit3 bit2 bit1 bit0
1265 * MCP and debug are strict
1266 */
1267 REG_WR(bp, NIG_REG_P0_TX_ARB_CLIENT_IS_STRICT, 0x1F);
1268 /*
1269 * For strict priority entries defines the number of consecutive slots
1270 * for the highest priority.
1271 */
1272 REG_WR(bp, NIG_REG_P0_TX_ARB_NUM_STRICT_ARB_SLOTS, 0x100);
1273 /* ETS mode disable */
1274 REG_WR(bp, PBF_REG_ETS_ENABLED, 0);
1275 /* Defines the number of consecutive slots for the strict priority */
1276 REG_WR(bp, PBF_REG_NUM_STRICT_ARB_SLOTS, 0x100);
1277
1278 /* Defines the number of consecutive slots for the strict priority */
1279 REG_WR(bp, PBF_REG_HIGH_PRIORITY_COS_NUM, strict_cos);
1280
1281 /*
1282 * mapping between entry priority to client number (0,1,2 -debug and
1283 * management clients, 3 - COS0 client, 4 - COS client)(HIGHEST)
1284 * 3bits client num.
1285 * PRI4 | PRI3 | PRI2 | PRI1 | PRI0
1286 * dbg0-010 dbg1-001 cos1-100 cos0-011 MCP-000
1287 * dbg0-010 dbg1-001 cos0-011 cos1-100 MCP-000
1288 */
1289 val = (0 == strict_cos) ? 0x2318 : 0x22E0;
1290 REG_WR(bp, NIG_REG_P0_TX_ARB_PRIORITY_CLIENT, val);
1291
1292 return 0;
1293 }
1294 /******************************************************************/
1295 /* PFC section */
1296 /******************************************************************/
1297
1298 static void bnx2x_update_pfc_xmac(struct link_params *params,
1299 struct link_vars *vars,
1300 u8 is_lb)
1301 {
1302 struct bnx2x *bp = params->bp;
1303 u32 xmac_base;
1304 u32 pause_val, pfc0_val, pfc1_val;
1305
1306 /* XMAC base adrr */
1307 xmac_base = (params->port) ? GRCBASE_XMAC1 : GRCBASE_XMAC0;
1308
1309 /* Initialize pause and pfc registers */
1310 pause_val = 0x18000;
1311 pfc0_val = 0xFFFF8000;
1312 pfc1_val = 0x2;
1313
1314 /* No PFC support */
1315 if (!(params->feature_config_flags &
1316 FEATURE_CONFIG_PFC_ENABLED)) {
1317
1318 /*
1319 * RX flow control - Process pause frame in receive direction
1320 */
1321 if (vars->flow_ctrl & BNX2X_FLOW_CTRL_RX)
1322 pause_val |= XMAC_PAUSE_CTRL_REG_RX_PAUSE_EN;
1323
1324 /*
1325 * TX flow control - Send pause packet when buffer is full
1326 */
1327 if (vars->flow_ctrl & BNX2X_FLOW_CTRL_TX)
1328 pause_val |= XMAC_PAUSE_CTRL_REG_TX_PAUSE_EN;
1329 } else {/* PFC support */
1330 pfc1_val |= XMAC_PFC_CTRL_HI_REG_PFC_REFRESH_EN |
1331 XMAC_PFC_CTRL_HI_REG_PFC_STATS_EN |
1332 XMAC_PFC_CTRL_HI_REG_RX_PFC_EN |
1333 XMAC_PFC_CTRL_HI_REG_TX_PFC_EN;
1334 }
1335
1336 /* Write pause and PFC registers */
1337 REG_WR(bp, xmac_base + XMAC_REG_PAUSE_CTRL, pause_val);
1338 REG_WR(bp, xmac_base + XMAC_REG_PFC_CTRL, pfc0_val);
1339 REG_WR(bp, xmac_base + XMAC_REG_PFC_CTRL_HI, pfc1_val);
1340
1341
1342 /* Set MAC address for source TX Pause/PFC frames */
1343 REG_WR(bp, xmac_base + XMAC_REG_CTRL_SA_LO,
1344 ((params->mac_addr[2] << 24) |
1345 (params->mac_addr[3] << 16) |
1346 (params->mac_addr[4] << 8) |
1347 (params->mac_addr[5])));
1348 REG_WR(bp, xmac_base + XMAC_REG_CTRL_SA_HI,
1349 ((params->mac_addr[0] << 8) |
1350 (params->mac_addr[1])));
1351
1352 udelay(30);
1353 }
1354
1355
1356 static void bnx2x_emac_get_pfc_stat(struct link_params *params,
1357 u32 pfc_frames_sent[2],
1358 u32 pfc_frames_received[2])
1359 {
1360 /* Read pfc statistic */
1361 struct bnx2x *bp = params->bp;
1362 u32 emac_base = params->port ? GRCBASE_EMAC1 : GRCBASE_EMAC0;
1363 u32 val_xon = 0;
1364 u32 val_xoff = 0;
1365
1366 DP(NETIF_MSG_LINK, "pfc statistic read from EMAC\n");
1367
1368 /* PFC received frames */
1369 val_xoff = REG_RD(bp, emac_base +
1370 EMAC_REG_RX_PFC_STATS_XOFF_RCVD);
1371 val_xoff &= EMAC_REG_RX_PFC_STATS_XOFF_RCVD_COUNT;
1372 val_xon = REG_RD(bp, emac_base + EMAC_REG_RX_PFC_STATS_XON_RCVD);
1373 val_xon &= EMAC_REG_RX_PFC_STATS_XON_RCVD_COUNT;
1374
1375 pfc_frames_received[0] = val_xon + val_xoff;
1376
1377 /* PFC received sent */
1378 val_xoff = REG_RD(bp, emac_base +
1379 EMAC_REG_RX_PFC_STATS_XOFF_SENT);
1380 val_xoff &= EMAC_REG_RX_PFC_STATS_XOFF_SENT_COUNT;
1381 val_xon = REG_RD(bp, emac_base + EMAC_REG_RX_PFC_STATS_XON_SENT);
1382 val_xon &= EMAC_REG_RX_PFC_STATS_XON_SENT_COUNT;
1383
1384 pfc_frames_sent[0] = val_xon + val_xoff;
1385 }
1386
1387 /* Read pfc statistic*/
1388 void bnx2x_pfc_statistic(struct link_params *params, struct link_vars *vars,
1389 u32 pfc_frames_sent[2],
1390 u32 pfc_frames_received[2])
1391 {
1392 /* Read pfc statistic */
1393 struct bnx2x *bp = params->bp;
1394
1395 DP(NETIF_MSG_LINK, "pfc statistic\n");
1396
1397 if (!vars->link_up)
1398 return;
1399
1400 if (MAC_TYPE_EMAC == vars->mac_type) {
1401 DP(NETIF_MSG_LINK, "About to read PFC stats from EMAC\n");
1402 bnx2x_emac_get_pfc_stat(params, pfc_frames_sent,
1403 pfc_frames_received);
1404 }
1405 }
1406 /******************************************************************/
1407 /* MAC/PBF section */
1408 /******************************************************************/
1409 static void bnx2x_set_mdio_clk(struct bnx2x *bp, u32 chip_id, u8 port)
1410 {
1411 u32 mode, emac_base;
1412 /**
1413 * Set clause 45 mode, slow down the MDIO clock to 2.5MHz
1414 * (a value of 49==0x31) and make sure that the AUTO poll is off
1415 */
1416
1417 if (CHIP_IS_E2(bp))
1418 emac_base = GRCBASE_EMAC0;
1419 else
1420 emac_base = (port) ? GRCBASE_EMAC1 : GRCBASE_EMAC0;
1421 mode = REG_RD(bp, emac_base + EMAC_REG_EMAC_MDIO_MODE);
1422 mode &= ~(EMAC_MDIO_MODE_AUTO_POLL |
1423 EMAC_MDIO_MODE_CLOCK_CNT);
1424 if (USES_WARPCORE(bp))
1425 mode |= (74L << EMAC_MDIO_MODE_CLOCK_CNT_BITSHIFT);
1426 else
1427 mode |= (49L << EMAC_MDIO_MODE_CLOCK_CNT_BITSHIFT);
1428
1429 mode |= (EMAC_MDIO_MODE_CLAUSE_45);
1430 REG_WR(bp, emac_base + EMAC_REG_EMAC_MDIO_MODE, mode);
1431
1432 udelay(40);
1433 }
1434
1435 static void bnx2x_emac_init(struct link_params *params,
1436 struct link_vars *vars)
1437 {
1438 /* reset and unreset the emac core */
1439 struct bnx2x *bp = params->bp;
1440 u8 port = params->port;
1441 u32 emac_base = port ? GRCBASE_EMAC1 : GRCBASE_EMAC0;
1442 u32 val;
1443 u16 timeout;
1444
1445 REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR,
1446 (MISC_REGISTERS_RESET_REG_2_RST_EMAC0_HARD_CORE << port));
1447 udelay(5);
1448 REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET,
1449 (MISC_REGISTERS_RESET_REG_2_RST_EMAC0_HARD_CORE << port));
1450
1451 /* init emac - use read-modify-write */
1452 /* self clear reset */
1453 val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE);
1454 EMAC_WR(bp, EMAC_REG_EMAC_MODE, (val | EMAC_MODE_RESET));
1455
1456 timeout = 200;
1457 do {
1458 val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE);
1459 DP(NETIF_MSG_LINK, "EMAC reset reg is %u\n", val);
1460 if (!timeout) {
1461 DP(NETIF_MSG_LINK, "EMAC timeout!\n");
1462 return;
1463 }
1464 timeout--;
1465 } while (val & EMAC_MODE_RESET);
1466 bnx2x_set_mdio_clk(bp, params->chip_id, port);
1467 /* Set mac address */
1468 val = ((params->mac_addr[0] << 8) |
1469 params->mac_addr[1]);
1470 EMAC_WR(bp, EMAC_REG_EMAC_MAC_MATCH, val);
1471
1472 val = ((params->mac_addr[2] << 24) |
1473 (params->mac_addr[3] << 16) |
1474 (params->mac_addr[4] << 8) |
1475 params->mac_addr[5]);
1476 EMAC_WR(bp, EMAC_REG_EMAC_MAC_MATCH + 4, val);
1477 }
1478
1479 static void bnx2x_set_xumac_nig(struct link_params *params,
1480 u16 tx_pause_en,
1481 u8 enable)
1482 {
1483 struct bnx2x *bp = params->bp;
1484
1485 REG_WR(bp, params->port ? NIG_REG_P1_MAC_IN_EN : NIG_REG_P0_MAC_IN_EN,
1486 enable);
1487 REG_WR(bp, params->port ? NIG_REG_P1_MAC_OUT_EN : NIG_REG_P0_MAC_OUT_EN,
1488 enable);
1489 REG_WR(bp, params->port ? NIG_REG_P1_MAC_PAUSE_OUT_EN :
1490 NIG_REG_P0_MAC_PAUSE_OUT_EN, tx_pause_en);
1491 }
1492
1493 static void bnx2x_umac_enable(struct link_params *params,
1494 struct link_vars *vars, u8 lb)
1495 {
1496 u32 val;
1497 u32 umac_base = params->port ? GRCBASE_UMAC1 : GRCBASE_UMAC0;
1498 struct bnx2x *bp = params->bp;
1499 /* Reset UMAC */
1500 REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR,
1501 (MISC_REGISTERS_RESET_REG_2_UMAC0 << params->port));
1502 usleep_range(1000, 1000);
1503
1504 REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET,
1505 (MISC_REGISTERS_RESET_REG_2_UMAC0 << params->port));
1506
1507 DP(NETIF_MSG_LINK, "enabling UMAC\n");
1508
1509 /**
1510 * This register determines on which events the MAC will assert
1511 * error on the i/f to the NIG along w/ EOP.
1512 */
1513
1514 /**
1515 * BD REG_WR(bp, NIG_REG_P0_MAC_RSV_ERR_MASK +
1516 * params->port*0x14, 0xfffff.
1517 */
1518 /* This register opens the gate for the UMAC despite its name */
1519 REG_WR(bp, NIG_REG_EGRESS_EMAC0_PORT + params->port*4, 1);
1520
1521 val = UMAC_COMMAND_CONFIG_REG_PROMIS_EN |
1522 UMAC_COMMAND_CONFIG_REG_PAD_EN |
1523 UMAC_COMMAND_CONFIG_REG_SW_RESET |
1524 UMAC_COMMAND_CONFIG_REG_NO_LGTH_CHECK;
1525 switch (vars->line_speed) {
1526 case SPEED_10:
1527 val |= (0<<2);
1528 break;
1529 case SPEED_100:
1530 val |= (1<<2);
1531 break;
1532 case SPEED_1000:
1533 val |= (2<<2);
1534 break;
1535 case SPEED_2500:
1536 val |= (3<<2);
1537 break;
1538 default:
1539 DP(NETIF_MSG_LINK, "Invalid speed for UMAC %d\n",
1540 vars->line_speed);
1541 break;
1542 }
1543 if (!(vars->flow_ctrl & BNX2X_FLOW_CTRL_TX))
1544 val |= UMAC_COMMAND_CONFIG_REG_IGNORE_TX_PAUSE;
1545
1546 if (!(vars->flow_ctrl & BNX2X_FLOW_CTRL_RX))
1547 val |= UMAC_COMMAND_CONFIG_REG_PAUSE_IGNORE;
1548
1549 REG_WR(bp, umac_base + UMAC_REG_COMMAND_CONFIG, val);
1550 udelay(50);
1551
1552 /* Set MAC address for source TX Pause/PFC frames (under SW reset) */
1553 REG_WR(bp, umac_base + UMAC_REG_MAC_ADDR0,
1554 ((params->mac_addr[2] << 24) |
1555 (params->mac_addr[3] << 16) |
1556 (params->mac_addr[4] << 8) |
1557 (params->mac_addr[5])));
1558 REG_WR(bp, umac_base + UMAC_REG_MAC_ADDR1,
1559 ((params->mac_addr[0] << 8) |
1560 (params->mac_addr[1])));
1561
1562 /* Enable RX and TX */
1563 val &= ~UMAC_COMMAND_CONFIG_REG_PAD_EN;
1564 val |= UMAC_COMMAND_CONFIG_REG_TX_ENA |
1565 UMAC_COMMAND_CONFIG_REG_RX_ENA;
1566 REG_WR(bp, umac_base + UMAC_REG_COMMAND_CONFIG, val);
1567 udelay(50);
1568
1569 /* Remove SW Reset */
1570 val &= ~UMAC_COMMAND_CONFIG_REG_SW_RESET;
1571
1572 /* Check loopback mode */
1573 if (lb)
1574 val |= UMAC_COMMAND_CONFIG_REG_LOOP_ENA;
1575 REG_WR(bp, umac_base + UMAC_REG_COMMAND_CONFIG, val);
1576
1577 /*
1578 * Maximum Frame Length (RW). Defines a 14-Bit maximum frame
1579 * length used by the MAC receive logic to check frames.
1580 */
1581 REG_WR(bp, umac_base + UMAC_REG_MAXFR, 0x2710);
1582 bnx2x_set_xumac_nig(params,
1583 ((vars->flow_ctrl & BNX2X_FLOW_CTRL_TX) != 0), 1);
1584 vars->mac_type = MAC_TYPE_UMAC;
1585
1586 }
1587
1588 static u8 bnx2x_is_4_port_mode(struct bnx2x *bp)
1589 {
1590 u32 port4mode_ovwr_val;
1591 /* Check 4-port override enabled */
1592 port4mode_ovwr_val = REG_RD(bp, MISC_REG_PORT4MODE_EN_OVWR);
1593 if (port4mode_ovwr_val & (1<<0)) {
1594 /* Return 4-port mode override value */
1595 return ((port4mode_ovwr_val & (1<<1)) == (1<<1));
1596 }
1597 /* Return 4-port mode from input pin */
1598 return (u8)REG_RD(bp, MISC_REG_PORT4MODE_EN);
1599 }
1600
1601 /* Define the XMAC mode */
1602 static void bnx2x_xmac_init(struct bnx2x *bp, u32 max_speed)
1603 {
1604 u32 is_port4mode = bnx2x_is_4_port_mode(bp);
1605
1606 /**
1607 * In 4-port mode, need to set the mode only once, so if XMAC is
1608 * already out of reset, it means the mode has already been set,
1609 * and it must not* reset the XMAC again, since it controls both
1610 * ports of the path
1611 **/
1612
1613 if (is_port4mode && (REG_RD(bp, MISC_REG_RESET_REG_2) &
1614 MISC_REGISTERS_RESET_REG_2_XMAC)) {
1615 DP(NETIF_MSG_LINK, "XMAC already out of reset"
1616 " in 4-port mode\n");
1617 return;
1618 }
1619
1620 /* Hard reset */
1621 REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR,
1622 MISC_REGISTERS_RESET_REG_2_XMAC);
1623 usleep_range(1000, 1000);
1624
1625 REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET,
1626 MISC_REGISTERS_RESET_REG_2_XMAC);
1627 if (is_port4mode) {
1628 DP(NETIF_MSG_LINK, "Init XMAC to 2 ports x 10G per path\n");
1629
1630 /* Set the number of ports on the system side to up to 2 */
1631 REG_WR(bp, MISC_REG_XMAC_CORE_PORT_MODE, 1);
1632
1633 /* Set the number of ports on the Warp Core to 10G */
1634 REG_WR(bp, MISC_REG_XMAC_PHY_PORT_MODE, 3);
1635 } else {
1636 /* Set the number of ports on the system side to 1 */
1637 REG_WR(bp, MISC_REG_XMAC_CORE_PORT_MODE, 0);
1638 if (max_speed == SPEED_10000) {
1639 DP(NETIF_MSG_LINK, "Init XMAC to 10G x 1"
1640 " port per path\n");
1641 /* Set the number of ports on the Warp Core to 10G */
1642 REG_WR(bp, MISC_REG_XMAC_PHY_PORT_MODE, 3);
1643 } else {
1644 DP(NETIF_MSG_LINK, "Init XMAC to 20G x 2 ports"
1645 " per path\n");
1646 /* Set the number of ports on the Warp Core to 20G */
1647 REG_WR(bp, MISC_REG_XMAC_PHY_PORT_MODE, 1);
1648 }
1649 }
1650 /* Soft reset */
1651 REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR,
1652 MISC_REGISTERS_RESET_REG_2_XMAC_SOFT);
1653 usleep_range(1000, 1000);
1654
1655 REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET,
1656 MISC_REGISTERS_RESET_REG_2_XMAC_SOFT);
1657
1658 }
1659
1660 static void bnx2x_xmac_disable(struct link_params *params)
1661 {
1662 u8 port = params->port;
1663 struct bnx2x *bp = params->bp;
1664 u32 pfc_ctrl, xmac_base = (port) ? GRCBASE_XMAC1 : GRCBASE_XMAC0;
1665
1666 if (REG_RD(bp, MISC_REG_RESET_REG_2) &
1667 MISC_REGISTERS_RESET_REG_2_XMAC) {
1668 /*
1669 * Send an indication to change the state in the NIG back to XON
1670 * Clearing this bit enables the next set of this bit to get
1671 * rising edge
1672 */
1673 pfc_ctrl = REG_RD(bp, xmac_base + XMAC_REG_PFC_CTRL_HI);
1674 REG_WR(bp, xmac_base + XMAC_REG_PFC_CTRL_HI,
1675 (pfc_ctrl & ~(1<<1)));
1676 REG_WR(bp, xmac_base + XMAC_REG_PFC_CTRL_HI,
1677 (pfc_ctrl | (1<<1)));
1678 DP(NETIF_MSG_LINK, "Disable XMAC on port %x\n", port);
1679 REG_WR(bp, xmac_base + XMAC_REG_CTRL, 0);
1680 usleep_range(1000, 1000);
1681 bnx2x_set_xumac_nig(params, 0, 0);
1682 REG_WR(bp, xmac_base + XMAC_REG_CTRL,
1683 XMAC_CTRL_REG_SOFT_RESET);
1684 }
1685 }
1686
1687 static int bnx2x_xmac_enable(struct link_params *params,
1688 struct link_vars *vars, u8 lb)
1689 {
1690 u32 val, xmac_base;
1691 struct bnx2x *bp = params->bp;
1692 DP(NETIF_MSG_LINK, "enabling XMAC\n");
1693
1694 xmac_base = (params->port) ? GRCBASE_XMAC1 : GRCBASE_XMAC0;
1695
1696 bnx2x_xmac_init(bp, vars->line_speed);
1697
1698 /*
1699 * This register determines on which events the MAC will assert
1700 * error on the i/f to the NIG along w/ EOP.
1701 */
1702
1703 /*
1704 * This register tells the NIG whether to send traffic to UMAC
1705 * or XMAC
1706 */
1707 REG_WR(bp, NIG_REG_EGRESS_EMAC0_PORT + params->port*4, 0);
1708
1709 /* Set Max packet size */
1710 REG_WR(bp, xmac_base + XMAC_REG_RX_MAX_SIZE, 0x2710);
1711
1712 /* CRC append for Tx packets */
1713 REG_WR(bp, xmac_base + XMAC_REG_TX_CTRL, 0xC800);
1714
1715 /* update PFC */
1716 bnx2x_update_pfc_xmac(params, vars, 0);
1717
1718 /* Enable TX and RX */
1719 val = XMAC_CTRL_REG_TX_EN | XMAC_CTRL_REG_RX_EN;
1720
1721 /* Check loopback mode */
1722 if (lb)
1723 val |= XMAC_CTRL_REG_CORE_LOCAL_LPBK;
1724 REG_WR(bp, xmac_base + XMAC_REG_CTRL, val);
1725 bnx2x_set_xumac_nig(params,
1726 ((vars->flow_ctrl & BNX2X_FLOW_CTRL_TX) != 0), 1);
1727
1728 vars->mac_type = MAC_TYPE_XMAC;
1729
1730 return 0;
1731 }
1732 static int bnx2x_emac_enable(struct link_params *params,
1733 struct link_vars *vars, u8 lb)
1734 {
1735 struct bnx2x *bp = params->bp;
1736 u8 port = params->port;
1737 u32 emac_base = port ? GRCBASE_EMAC1 : GRCBASE_EMAC0;
1738 u32 val;
1739
1740 DP(NETIF_MSG_LINK, "enabling EMAC\n");
1741
1742 /* Disable BMAC */
1743 REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR,
1744 (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
1745
1746 /* enable emac and not bmac */
1747 REG_WR(bp, NIG_REG_EGRESS_EMAC0_PORT + port*4, 1);
1748
1749 /* ASIC */
1750 if (vars->phy_flags & PHY_XGXS_FLAG) {
1751 u32 ser_lane = ((params->lane_config &
1752 PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >>
1753 PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT);
1754
1755 DP(NETIF_MSG_LINK, "XGXS\n");
1756 /* select the master lanes (out of 0-3) */
1757 REG_WR(bp, NIG_REG_XGXS_LANE_SEL_P0 + port*4, ser_lane);
1758 /* select XGXS */
1759 REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL + port*4, 1);
1760
1761 } else { /* SerDes */
1762 DP(NETIF_MSG_LINK, "SerDes\n");
1763 /* select SerDes */
1764 REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL + port*4, 0);
1765 }
1766
1767 bnx2x_bits_en(bp, emac_base + EMAC_REG_EMAC_RX_MODE,
1768 EMAC_RX_MODE_RESET);
1769 bnx2x_bits_en(bp, emac_base + EMAC_REG_EMAC_TX_MODE,
1770 EMAC_TX_MODE_RESET);
1771
1772 if (CHIP_REV_IS_SLOW(bp)) {
1773 /* config GMII mode */
1774 val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE);
1775 EMAC_WR(bp, EMAC_REG_EMAC_MODE, (val | EMAC_MODE_PORT_GMII));
1776 } else { /* ASIC */
1777 /* pause enable/disable */
1778 bnx2x_bits_dis(bp, emac_base + EMAC_REG_EMAC_RX_MODE,
1779 EMAC_RX_MODE_FLOW_EN);
1780
1781 bnx2x_bits_dis(bp, emac_base + EMAC_REG_EMAC_TX_MODE,
1782 (EMAC_TX_MODE_EXT_PAUSE_EN |
1783 EMAC_TX_MODE_FLOW_EN));
1784 if (!(params->feature_config_flags &
1785 FEATURE_CONFIG_PFC_ENABLED)) {
1786 if (vars->flow_ctrl & BNX2X_FLOW_CTRL_RX)
1787 bnx2x_bits_en(bp, emac_base +
1788 EMAC_REG_EMAC_RX_MODE,
1789 EMAC_RX_MODE_FLOW_EN);
1790
1791 if (vars->flow_ctrl & BNX2X_FLOW_CTRL_TX)
1792 bnx2x_bits_en(bp, emac_base +
1793 EMAC_REG_EMAC_TX_MODE,
1794 (EMAC_TX_MODE_EXT_PAUSE_EN |
1795 EMAC_TX_MODE_FLOW_EN));
1796 } else
1797 bnx2x_bits_en(bp, emac_base + EMAC_REG_EMAC_TX_MODE,
1798 EMAC_TX_MODE_FLOW_EN);
1799 }
1800
1801 /* KEEP_VLAN_TAG, promiscuous */
1802 val = REG_RD(bp, emac_base + EMAC_REG_EMAC_RX_MODE);
1803 val |= EMAC_RX_MODE_KEEP_VLAN_TAG | EMAC_RX_MODE_PROMISCUOUS;
1804
1805 /*
1806 * Setting this bit causes MAC control frames (except for pause
1807 * frames) to be passed on for processing. This setting has no
1808 * affect on the operation of the pause frames. This bit effects
1809 * all packets regardless of RX Parser packet sorting logic.
1810 * Turn the PFC off to make sure we are in Xon state before
1811 * enabling it.
1812 */
1813 EMAC_WR(bp, EMAC_REG_RX_PFC_MODE, 0);
1814 if (params->feature_config_flags & FEATURE_CONFIG_PFC_ENABLED) {
1815 DP(NETIF_MSG_LINK, "PFC is enabled\n");
1816 /* Enable PFC again */
1817 EMAC_WR(bp, EMAC_REG_RX_PFC_MODE,
1818 EMAC_REG_RX_PFC_MODE_RX_EN |
1819 EMAC_REG_RX_PFC_MODE_TX_EN |
1820 EMAC_REG_RX_PFC_MODE_PRIORITIES);
1821
1822 EMAC_WR(bp, EMAC_REG_RX_PFC_PARAM,
1823 ((0x0101 <<
1824 EMAC_REG_RX_PFC_PARAM_OPCODE_BITSHIFT) |
1825 (0x00ff <<
1826 EMAC_REG_RX_PFC_PARAM_PRIORITY_EN_BITSHIFT)));
1827 val |= EMAC_RX_MODE_KEEP_MAC_CONTROL;
1828 }
1829 EMAC_WR(bp, EMAC_REG_EMAC_RX_MODE, val);
1830
1831 /* Set Loopback */
1832 val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE);
1833 if (lb)
1834 val |= 0x810;
1835 else
1836 val &= ~0x810;
1837 EMAC_WR(bp, EMAC_REG_EMAC_MODE, val);
1838
1839 /* enable emac */
1840 REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 1);
1841
1842 /* enable emac for jumbo packets */
1843 EMAC_WR(bp, EMAC_REG_EMAC_RX_MTU_SIZE,
1844 (EMAC_RX_MTU_SIZE_JUMBO_ENA |
1845 (ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD)));
1846
1847 /* strip CRC */
1848 REG_WR(bp, NIG_REG_NIG_INGRESS_EMAC0_NO_CRC + port*4, 0x1);
1849
1850 /* disable the NIG in/out to the bmac */
1851 REG_WR(bp, NIG_REG_BMAC0_IN_EN + port*4, 0x0);
1852 REG_WR(bp, NIG_REG_BMAC0_PAUSE_OUT_EN + port*4, 0x0);
1853 REG_WR(bp, NIG_REG_BMAC0_OUT_EN + port*4, 0x0);
1854
1855 /* enable the NIG in/out to the emac */
1856 REG_WR(bp, NIG_REG_EMAC0_IN_EN + port*4, 0x1);
1857 val = 0;
1858 if ((params->feature_config_flags &
1859 FEATURE_CONFIG_PFC_ENABLED) ||
1860 (vars->flow_ctrl & BNX2X_FLOW_CTRL_TX))
1861 val = 1;
1862
1863 REG_WR(bp, NIG_REG_EMAC0_PAUSE_OUT_EN + port*4, val);
1864 REG_WR(bp, NIG_REG_EGRESS_EMAC0_OUT_EN + port*4, 0x1);
1865
1866 REG_WR(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4, 0x0);
1867
1868 vars->mac_type = MAC_TYPE_EMAC;
1869 return 0;
1870 }
1871
1872 static void bnx2x_update_pfc_bmac1(struct link_params *params,
1873 struct link_vars *vars)
1874 {
1875 u32 wb_data[2];
1876 struct bnx2x *bp = params->bp;
1877 u32 bmac_addr = params->port ? NIG_REG_INGRESS_BMAC1_MEM :
1878 NIG_REG_INGRESS_BMAC0_MEM;
1879
1880 u32 val = 0x14;
1881 if ((!(params->feature_config_flags &
1882 FEATURE_CONFIG_PFC_ENABLED)) &&
1883 (vars->flow_ctrl & BNX2X_FLOW_CTRL_RX))
1884 /* Enable BigMAC to react on received Pause packets */
1885 val |= (1<<5);
1886 wb_data[0] = val;
1887 wb_data[1] = 0;
1888 REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_RX_CONTROL, wb_data, 2);
1889
1890 /* tx control */
1891 val = 0xc0;
1892 if (!(params->feature_config_flags &
1893 FEATURE_CONFIG_PFC_ENABLED) &&
1894 (vars->flow_ctrl & BNX2X_FLOW_CTRL_TX))
1895 val |= 0x800000;
1896 wb_data[0] = val;
1897 wb_data[1] = 0;
1898 REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_TX_CONTROL, wb_data, 2);
1899 }
1900
1901 static void bnx2x_update_pfc_bmac2(struct link_params *params,
1902 struct link_vars *vars,
1903 u8 is_lb)
1904 {
1905 /*
1906 * Set rx control: Strip CRC and enable BigMAC to relay
1907 * control packets to the system as well
1908 */
1909 u32 wb_data[2];
1910 struct bnx2x *bp = params->bp;
1911 u32 bmac_addr = params->port ? NIG_REG_INGRESS_BMAC1_MEM :
1912 NIG_REG_INGRESS_BMAC0_MEM;
1913 u32 val = 0x14;
1914
1915 if ((!(params->feature_config_flags &
1916 FEATURE_CONFIG_PFC_ENABLED)) &&
1917 (vars->flow_ctrl & BNX2X_FLOW_CTRL_RX))
1918 /* Enable BigMAC to react on received Pause packets */
1919 val |= (1<<5);
1920 wb_data[0] = val;
1921 wb_data[1] = 0;
1922 REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_RX_CONTROL, wb_data, 2);
1923 udelay(30);
1924
1925 /* Tx control */
1926 val = 0xc0;
1927 if (!(params->feature_config_flags &
1928 FEATURE_CONFIG_PFC_ENABLED) &&
1929 (vars->flow_ctrl & BNX2X_FLOW_CTRL_TX))
1930 val |= 0x800000;
1931 wb_data[0] = val;
1932 wb_data[1] = 0;
1933 REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_TX_CONTROL, wb_data, 2);
1934
1935 if (params->feature_config_flags & FEATURE_CONFIG_PFC_ENABLED) {
1936 DP(NETIF_MSG_LINK, "PFC is enabled\n");
1937 /* Enable PFC RX & TX & STATS and set 8 COS */
1938 wb_data[0] = 0x0;
1939 wb_data[0] |= (1<<0); /* RX */
1940 wb_data[0] |= (1<<1); /* TX */
1941 wb_data[0] |= (1<<2); /* Force initial Xon */
1942 wb_data[0] |= (1<<3); /* 8 cos */
1943 wb_data[0] |= (1<<5); /* STATS */
1944 wb_data[1] = 0;
1945 REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_PFC_CONTROL,
1946 wb_data, 2);
1947 /* Clear the force Xon */
1948 wb_data[0] &= ~(1<<2);
1949 } else {
1950 DP(NETIF_MSG_LINK, "PFC is disabled\n");
1951 /* disable PFC RX & TX & STATS and set 8 COS */
1952 wb_data[0] = 0x8;
1953 wb_data[1] = 0;
1954 }
1955
1956 REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_PFC_CONTROL, wb_data, 2);
1957
1958 /*
1959 * Set Time (based unit is 512 bit time) between automatic
1960 * re-sending of PP packets amd enable automatic re-send of
1961 * Per-Priroity Packet as long as pp_gen is asserted and
1962 * pp_disable is low.
1963 */
1964 val = 0x8000;
1965 if (params->feature_config_flags & FEATURE_CONFIG_PFC_ENABLED)
1966 val |= (1<<16); /* enable automatic re-send */
1967
1968 wb_data[0] = val;
1969 wb_data[1] = 0;
1970 REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_TX_PAUSE_CONTROL,
1971 wb_data, 2);
1972
1973 /* mac control */
1974 val = 0x3; /* Enable RX and TX */
1975 if (is_lb) {
1976 val |= 0x4; /* Local loopback */
1977 DP(NETIF_MSG_LINK, "enable bmac loopback\n");
1978 }
1979 /* When PFC enabled, Pass pause frames towards the NIG. */
1980 if (params->feature_config_flags & FEATURE_CONFIG_PFC_ENABLED)
1981 val |= ((1<<6)|(1<<5));
1982
1983 wb_data[0] = val;
1984 wb_data[1] = 0;
1985 REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_BMAC_CONTROL, wb_data, 2);
1986 }
1987
1988
1989 /* PFC BRB internal port configuration params */
1990 struct bnx2x_pfc_brb_threshold_val {
1991 u32 pause_xoff;
1992 u32 pause_xon;
1993 u32 full_xoff;
1994 u32 full_xon;
1995 };
1996
1997 struct bnx2x_pfc_brb_e3b0_val {
1998 u32 full_lb_xoff_th;
1999 u32 full_lb_xon_threshold;
2000 u32 lb_guarantied;
2001 u32 mac_0_class_t_guarantied;
2002 u32 mac_0_class_t_guarantied_hyst;
2003 u32 mac_1_class_t_guarantied;
2004 u32 mac_1_class_t_guarantied_hyst;
2005 };
2006
2007 struct bnx2x_pfc_brb_th_val {
2008 struct bnx2x_pfc_brb_threshold_val pauseable_th;
2009 struct bnx2x_pfc_brb_threshold_val non_pauseable_th;
2010 };
2011 static int bnx2x_pfc_brb_get_config_params(
2012 struct link_params *params,
2013 struct bnx2x_pfc_brb_th_val *config_val)
2014 {
2015 struct bnx2x *bp = params->bp;
2016 DP(NETIF_MSG_LINK, "Setting PFC BRB configuration\n");
2017 if (CHIP_IS_E2(bp)) {
2018 config_val->pauseable_th.pause_xoff =
2019 PFC_E2_BRB_MAC_PAUSE_XOFF_THR_PAUSE;
2020 config_val->pauseable_th.pause_xon =
2021 PFC_E2_BRB_MAC_PAUSE_XON_THR_PAUSE;
2022 config_val->pauseable_th.full_xoff =
2023 PFC_E2_BRB_MAC_FULL_XOFF_THR_PAUSE;
2024 config_val->pauseable_th.full_xon =
2025 PFC_E2_BRB_MAC_FULL_XON_THR_PAUSE;
2026 /* non pause able*/
2027 config_val->non_pauseable_th.pause_xoff =
2028 PFC_E2_BRB_MAC_PAUSE_XOFF_THR_NON_PAUSE;
2029 config_val->non_pauseable_th.pause_xon =
2030 PFC_E2_BRB_MAC_PAUSE_XON_THR_NON_PAUSE;
2031 config_val->non_pauseable_th.full_xoff =
2032 PFC_E2_BRB_MAC_FULL_XOFF_THR_NON_PAUSE;
2033 config_val->non_pauseable_th.full_xon =
2034 PFC_E2_BRB_MAC_FULL_XON_THR_NON_PAUSE;
2035 } else if (CHIP_IS_E3A0(bp)) {
2036 config_val->pauseable_th.pause_xoff =
2037 PFC_E3A0_BRB_MAC_PAUSE_XOFF_THR_PAUSE;
2038 config_val->pauseable_th.pause_xon =
2039 PFC_E3A0_BRB_MAC_PAUSE_XON_THR_PAUSE;
2040 config_val->pauseable_th.full_xoff =
2041 PFC_E3A0_BRB_MAC_FULL_XOFF_THR_PAUSE;
2042 config_val->pauseable_th.full_xon =
2043 PFC_E3A0_BRB_MAC_FULL_XON_THR_PAUSE;
2044 /* non pause able*/
2045 config_val->non_pauseable_th.pause_xoff =
2046 PFC_E3A0_BRB_MAC_PAUSE_XOFF_THR_NON_PAUSE;
2047 config_val->non_pauseable_th.pause_xon =
2048 PFC_E3A0_BRB_MAC_PAUSE_XON_THR_NON_PAUSE;
2049 config_val->non_pauseable_th.full_xoff =
2050 PFC_E3A0_BRB_MAC_FULL_XOFF_THR_NON_PAUSE;
2051 config_val->non_pauseable_th.full_xon =
2052 PFC_E3A0_BRB_MAC_FULL_XON_THR_NON_PAUSE;
2053 } else if (CHIP_IS_E3B0(bp)) {
2054 if (params->phy[INT_PHY].flags &
2055 FLAGS_4_PORT_MODE) {
2056 config_val->pauseable_th.pause_xoff =
2057 PFC_E3B0_4P_BRB_MAC_PAUSE_XOFF_THR_PAUSE;
2058 config_val->pauseable_th.pause_xon =
2059 PFC_E3B0_4P_BRB_MAC_PAUSE_XON_THR_PAUSE;
2060 config_val->pauseable_th.full_xoff =
2061 PFC_E3B0_4P_BRB_MAC_FULL_XOFF_THR_PAUSE;
2062 config_val->pauseable_th.full_xon =
2063 PFC_E3B0_4P_BRB_MAC_FULL_XON_THR_PAUSE;
2064 /* non pause able*/
2065 config_val->non_pauseable_th.pause_xoff =
2066 PFC_E3B0_4P_BRB_MAC_PAUSE_XOFF_THR_NON_PAUSE;
2067 config_val->non_pauseable_th.pause_xon =
2068 PFC_E3B0_4P_BRB_MAC_PAUSE_XON_THR_NON_PAUSE;
2069 config_val->non_pauseable_th.full_xoff =
2070 PFC_E3B0_4P_BRB_MAC_FULL_XOFF_THR_NON_PAUSE;
2071 config_val->non_pauseable_th.full_xon =
2072 PFC_E3B0_4P_BRB_MAC_FULL_XON_THR_NON_PAUSE;
2073 } else {
2074 config_val->pauseable_th.pause_xoff =
2075 PFC_E3B0_2P_BRB_MAC_PAUSE_XOFF_THR_PAUSE;
2076 config_val->pauseable_th.pause_xon =
2077 PFC_E3B0_2P_BRB_MAC_PAUSE_XON_THR_PAUSE;
2078 config_val->pauseable_th.full_xoff =
2079 PFC_E3B0_2P_BRB_MAC_FULL_XOFF_THR_PAUSE;
2080 config_val->pauseable_th.full_xon =
2081 PFC_E3B0_2P_BRB_MAC_FULL_XON_THR_PAUSE;
2082 /* non pause able*/
2083 config_val->non_pauseable_th.pause_xoff =
2084 PFC_E3B0_2P_BRB_MAC_PAUSE_XOFF_THR_NON_PAUSE;
2085 config_val->non_pauseable_th.pause_xon =
2086 PFC_E3B0_2P_BRB_MAC_PAUSE_XON_THR_NON_PAUSE;
2087 config_val->non_pauseable_th.full_xoff =
2088 PFC_E3B0_2P_BRB_MAC_FULL_XOFF_THR_NON_PAUSE;
2089 config_val->non_pauseable_th.full_xon =
2090 PFC_E3B0_2P_BRB_MAC_FULL_XON_THR_NON_PAUSE;
2091 }
2092 } else
2093 return -EINVAL;
2094
2095 return 0;
2096 }
2097
2098
2099 static void bnx2x_pfc_brb_get_e3b0_config_params(struct link_params *params,
2100 struct bnx2x_pfc_brb_e3b0_val
2101 *e3b0_val,
2102 u32 cos0_pauseable,
2103 u32 cos1_pauseable)
2104 {
2105 if (params->phy[INT_PHY].flags & FLAGS_4_PORT_MODE) {
2106 e3b0_val->full_lb_xoff_th =
2107 PFC_E3B0_4P_BRB_FULL_LB_XOFF_THR;
2108 e3b0_val->full_lb_xon_threshold =
2109 PFC_E3B0_4P_BRB_FULL_LB_XON_THR;
2110 e3b0_val->lb_guarantied =
2111 PFC_E3B0_4P_LB_GUART;
2112 e3b0_val->mac_0_class_t_guarantied =
2113 PFC_E3B0_4P_BRB_MAC_0_CLASS_T_GUART;
2114 e3b0_val->mac_0_class_t_guarantied_hyst =
2115 PFC_E3B0_4P_BRB_MAC_0_CLASS_T_GUART_HYST;
2116 e3b0_val->mac_1_class_t_guarantied =
2117 PFC_E3B0_4P_BRB_MAC_1_CLASS_T_GUART;
2118 e3b0_val->mac_1_class_t_guarantied_hyst =
2119 PFC_E3B0_4P_BRB_MAC_1_CLASS_T_GUART_HYST;
2120 } else {
2121 e3b0_val->full_lb_xoff_th =
2122 PFC_E3B0_2P_BRB_FULL_LB_XOFF_THR;
2123 e3b0_val->full_lb_xon_threshold =
2124 PFC_E3B0_2P_BRB_FULL_LB_XON_THR;
2125 e3b0_val->mac_0_class_t_guarantied_hyst =
2126 PFC_E3B0_2P_BRB_MAC_0_CLASS_T_GUART_HYST;
2127 e3b0_val->mac_1_class_t_guarantied =
2128 PFC_E3B0_2P_BRB_MAC_1_CLASS_T_GUART;
2129 e3b0_val->mac_1_class_t_guarantied_hyst =
2130 PFC_E3B0_2P_BRB_MAC_1_CLASS_T_GUART_HYST;
2131
2132 if (cos0_pauseable != cos1_pauseable) {
2133 /* nonpauseable= Lossy + pauseable = Lossless*/
2134 e3b0_val->lb_guarantied =
2135 PFC_E3B0_2P_MIX_PAUSE_LB_GUART;
2136 e3b0_val->mac_0_class_t_guarantied =
2137 PFC_E3B0_2P_MIX_PAUSE_MAC_0_CLASS_T_GUART;
2138 } else if (cos0_pauseable) {
2139 /* Lossless +Lossless*/
2140 e3b0_val->lb_guarantied =
2141 PFC_E3B0_2P_PAUSE_LB_GUART;
2142 e3b0_val->mac_0_class_t_guarantied =
2143 PFC_E3B0_2P_PAUSE_MAC_0_CLASS_T_GUART;
2144 } else {
2145 /* Lossy +Lossy*/
2146 e3b0_val->lb_guarantied =
2147 PFC_E3B0_2P_NON_PAUSE_LB_GUART;
2148 e3b0_val->mac_0_class_t_guarantied =
2149 PFC_E3B0_2P_NON_PAUSE_MAC_0_CLASS_T_GUART;
2150 }
2151 }
2152 }
2153 static int bnx2x_update_pfc_brb(struct link_params *params,
2154 struct link_vars *vars,
2155 struct bnx2x_nig_brb_pfc_port_params
2156 *pfc_params)
2157 {
2158 struct bnx2x *bp = params->bp;
2159 struct bnx2x_pfc_brb_th_val config_val = { {0} };
2160 struct bnx2x_pfc_brb_threshold_val *reg_th_config =
2161 &config_val.pauseable_th;
2162 struct bnx2x_pfc_brb_e3b0_val e3b0_val = {0};
2163 int set_pfc = params->feature_config_flags &
2164 FEATURE_CONFIG_PFC_ENABLED;
2165 int bnx2x_status = 0;
2166 u8 port = params->port;
2167
2168 /* default - pause configuration */
2169 reg_th_config = &config_val.pauseable_th;
2170 bnx2x_status = bnx2x_pfc_brb_get_config_params(params, &config_val);
2171 if (0 != bnx2x_status)
2172 return bnx2x_status;
2173
2174 if (set_pfc && pfc_params)
2175 /* First COS */
2176 if (!pfc_params->cos0_pauseable)
2177 reg_th_config = &config_val.non_pauseable_th;
2178 /*
2179 * The number of free blocks below which the pause signal to class 0
2180 * of MAC #n is asserted. n=0,1
2181 */
2182 REG_WR(bp, (port) ? BRB1_REG_PAUSE_0_XOFF_THRESHOLD_1 :
2183 BRB1_REG_PAUSE_0_XOFF_THRESHOLD_0 ,
2184 reg_th_config->pause_xoff);
2185 /*
2186 * The number of free blocks above which the pause signal to class 0
2187 * of MAC #n is de-asserted. n=0,1
2188 */
2189 REG_WR(bp, (port) ? BRB1_REG_PAUSE_0_XON_THRESHOLD_1 :
2190 BRB1_REG_PAUSE_0_XON_THRESHOLD_0 , reg_th_config->pause_xon);
2191 /*
2192 * The number of free blocks below which the full signal to class 0
2193 * of MAC #n is asserted. n=0,1
2194 */
2195 REG_WR(bp, (port) ? BRB1_REG_FULL_0_XOFF_THRESHOLD_1 :
2196 BRB1_REG_FULL_0_XOFF_THRESHOLD_0 , reg_th_config->full_xoff);
2197 /*
2198 * The number of free blocks above which the full signal to class 0
2199 * of MAC #n is de-asserted. n=0,1
2200 */
2201 REG_WR(bp, (port) ? BRB1_REG_FULL_0_XON_THRESHOLD_1 :
2202 BRB1_REG_FULL_0_XON_THRESHOLD_0 , reg_th_config->full_xon);
2203
2204 if (set_pfc && pfc_params) {
2205 /* Second COS */
2206 if (pfc_params->cos1_pauseable)
2207 reg_th_config = &config_val.pauseable_th;
2208 else
2209 reg_th_config = &config_val.non_pauseable_th;
2210 /*
2211 * The number of free blocks below which the pause signal to
2212 * class 1 of MAC #n is asserted. n=0,1
2213 **/
2214 REG_WR(bp, (port) ? BRB1_REG_PAUSE_1_XOFF_THRESHOLD_1 :
2215 BRB1_REG_PAUSE_1_XOFF_THRESHOLD_0,
2216 reg_th_config->pause_xoff);
2217 /*
2218 * The number of free blocks above which the pause signal to
2219 * class 1 of MAC #n is de-asserted. n=0,1
2220 */
2221 REG_WR(bp, (port) ? BRB1_REG_PAUSE_1_XON_THRESHOLD_1 :
2222 BRB1_REG_PAUSE_1_XON_THRESHOLD_0,
2223 reg_th_config->pause_xon);
2224 /*
2225 * The number of free blocks below which the full signal to
2226 * class 1 of MAC #n is asserted. n=0,1
2227 */
2228 REG_WR(bp, (port) ? BRB1_REG_FULL_1_XOFF_THRESHOLD_1 :
2229 BRB1_REG_FULL_1_XOFF_THRESHOLD_0,
2230 reg_th_config->full_xoff);
2231 /*
2232 * The number of free blocks above which the full signal to
2233 * class 1 of MAC #n is de-asserted. n=0,1
2234 */
2235 REG_WR(bp, (port) ? BRB1_REG_FULL_1_XON_THRESHOLD_1 :
2236 BRB1_REG_FULL_1_XON_THRESHOLD_0,
2237 reg_th_config->full_xon);
2238
2239
2240 if (CHIP_IS_E3B0(bp)) {
2241 /*Should be done by init tool */
2242 /*
2243 * BRB_empty_for_dup = BRB1_REG_BRB_EMPTY_THRESHOLD
2244 * reset value
2245 * 944
2246 */
2247
2248 /**
2249 * The hysteresis on the guarantied buffer space for the Lb port
2250 * before signaling XON.
2251 **/
2252 REG_WR(bp, BRB1_REG_LB_GUARANTIED_HYST, 80);
2253
2254 bnx2x_pfc_brb_get_e3b0_config_params(
2255 params,
2256 &e3b0_val,
2257 pfc_params->cos0_pauseable,
2258 pfc_params->cos1_pauseable);
2259 /**
2260 * The number of free blocks below which the full signal to the
2261 * LB port is asserted.
2262 */
2263 REG_WR(bp, BRB1_REG_FULL_LB_XOFF_THRESHOLD,
2264 e3b0_val.full_lb_xoff_th);
2265 /**
2266 * The number of free blocks above which the full signal to the
2267 * LB port is de-asserted.
2268 */
2269 REG_WR(bp, BRB1_REG_FULL_LB_XON_THRESHOLD,
2270 e3b0_val.full_lb_xon_threshold);
2271 /**
2272 * The number of blocks guarantied for the MAC #n port. n=0,1
2273 */
2274
2275 /*The number of blocks guarantied for the LB port.*/
2276 REG_WR(bp, BRB1_REG_LB_GUARANTIED,
2277 e3b0_val.lb_guarantied);
2278
2279 /**
2280 * The number of blocks guarantied for the MAC #n port.
2281 */
2282 REG_WR(bp, BRB1_REG_MAC_GUARANTIED_0,
2283 2 * e3b0_val.mac_0_class_t_guarantied);
2284 REG_WR(bp, BRB1_REG_MAC_GUARANTIED_1,
2285 2 * e3b0_val.mac_1_class_t_guarantied);
2286 /**
2287 * The number of blocks guarantied for class #t in MAC0. t=0,1
2288 */
2289 REG_WR(bp, BRB1_REG_MAC_0_CLASS_0_GUARANTIED,
2290 e3b0_val.mac_0_class_t_guarantied);
2291 REG_WR(bp, BRB1_REG_MAC_0_CLASS_1_GUARANTIED,
2292 e3b0_val.mac_0_class_t_guarantied);
2293 /**
2294 * The hysteresis on the guarantied buffer space for class in
2295 * MAC0. t=0,1
2296 */
2297 REG_WR(bp, BRB1_REG_MAC_0_CLASS_0_GUARANTIED_HYST,
2298 e3b0_val.mac_0_class_t_guarantied_hyst);
2299 REG_WR(bp, BRB1_REG_MAC_0_CLASS_1_GUARANTIED_HYST,
2300 e3b0_val.mac_0_class_t_guarantied_hyst);
2301
2302 /**
2303 * The number of blocks guarantied for class #t in MAC1.t=0,1
2304 */
2305 REG_WR(bp, BRB1_REG_MAC_1_CLASS_0_GUARANTIED,
2306 e3b0_val.mac_1_class_t_guarantied);
2307 REG_WR(bp, BRB1_REG_MAC_1_CLASS_1_GUARANTIED,
2308 e3b0_val.mac_1_class_t_guarantied);
2309 /**
2310 * The hysteresis on the guarantied buffer space for class #t
2311 * in MAC1. t=0,1
2312 */
2313 REG_WR(bp, BRB1_REG_MAC_1_CLASS_0_GUARANTIED_HYST,
2314 e3b0_val.mac_1_class_t_guarantied_hyst);
2315 REG_WR(bp, BRB1_REG_MAC_1_CLASS_1_GUARANTIED_HYST,
2316 e3b0_val.mac_1_class_t_guarantied_hyst);
2317
2318 }
2319
2320 }
2321
2322 return bnx2x_status;
2323 }
2324
2325 /******************************************************************************
2326 * Description:
2327 * This function is needed because NIG ARB_CREDIT_WEIGHT_X are
2328 * not continues and ARB_CREDIT_WEIGHT_0 + offset is suitable.
2329 ******************************************************************************/
2330 int bnx2x_pfc_nig_rx_priority_mask(struct bnx2x *bp,
2331 u8 cos_entry,
2332 u32 priority_mask, u8 port)
2333 {
2334 u32 nig_reg_rx_priority_mask_add = 0;
2335
2336 switch (cos_entry) {
2337 case 0:
2338 nig_reg_rx_priority_mask_add = (port) ?
2339 NIG_REG_P1_RX_COS0_PRIORITY_MASK :
2340 NIG_REG_P0_RX_COS0_PRIORITY_MASK;
2341 break;
2342 case 1:
2343 nig_reg_rx_priority_mask_add = (port) ?
2344 NIG_REG_P1_RX_COS1_PRIORITY_MASK :
2345 NIG_REG_P0_RX_COS1_PRIORITY_MASK;
2346 break;
2347 case 2:
2348 nig_reg_rx_priority_mask_add = (port) ?
2349 NIG_REG_P1_RX_COS2_PRIORITY_MASK :
2350 NIG_REG_P0_RX_COS2_PRIORITY_MASK;
2351 break;
2352 case 3:
2353 if (port)
2354 return -EINVAL;
2355 nig_reg_rx_priority_mask_add = NIG_REG_P0_RX_COS3_PRIORITY_MASK;
2356 break;
2357 case 4:
2358 if (port)
2359 return -EINVAL;
2360 nig_reg_rx_priority_mask_add = NIG_REG_P0_RX_COS4_PRIORITY_MASK;
2361 break;
2362 case 5:
2363 if (port)
2364 return -EINVAL;
2365 nig_reg_rx_priority_mask_add = NIG_REG_P0_RX_COS5_PRIORITY_MASK;
2366 break;
2367 }
2368
2369 REG_WR(bp, nig_reg_rx_priority_mask_add, priority_mask);
2370
2371 return 0;
2372 }
2373 static void bnx2x_update_mng(struct link_params *params, u32 link_status)
2374 {
2375 struct bnx2x *bp = params->bp;
2376
2377 REG_WR(bp, params->shmem_base +
2378 offsetof(struct shmem_region,
2379 port_mb[params->port].link_status), link_status);
2380 }
2381
2382 static void bnx2x_update_pfc_nig(struct link_params *params,
2383 struct link_vars *vars,
2384 struct bnx2x_nig_brb_pfc_port_params *nig_params)
2385 {
2386 u32 xcm_mask = 0, ppp_enable = 0, pause_enable = 0, llfc_out_en = 0;
2387 u32 llfc_enable = 0, xcm0_out_en = 0, p0_hwpfc_enable = 0;
2388 u32 pkt_priority_to_cos = 0;
2389 struct bnx2x *bp = params->bp;
2390 u8 port = params->port;
2391
2392 int set_pfc = params->feature_config_flags &
2393 FEATURE_CONFIG_PFC_ENABLED;
2394 DP(NETIF_MSG_LINK, "updating pfc nig parameters\n");
2395
2396 /*
2397 * When NIG_LLH0_XCM_MASK_REG_LLHX_XCM_MASK_BCN bit is set
2398 * MAC control frames (that are not pause packets)
2399 * will be forwarded to the XCM.
2400 */
2401 xcm_mask = REG_RD(bp,
2402 port ? NIG_REG_LLH1_XCM_MASK :
2403 NIG_REG_LLH0_XCM_MASK);
2404 /*
2405 * nig params will override non PFC params, since it's possible to
2406 * do transition from PFC to SAFC
2407 */
2408 if (set_pfc) {
2409 pause_enable = 0;
2410 llfc_out_en = 0;
2411 llfc_enable = 0;
2412 if (CHIP_IS_E3(bp))
2413 ppp_enable = 0;
2414 else
2415 ppp_enable = 1;
2416 xcm_mask &= ~(port ? NIG_LLH1_XCM_MASK_REG_LLH1_XCM_MASK_BCN :
2417 NIG_LLH0_XCM_MASK_REG_LLH0_XCM_MASK_BCN);
2418 xcm0_out_en = 0;
2419 p0_hwpfc_enable = 1;
2420 } else {
2421 if (nig_params) {
2422 llfc_out_en = nig_params->llfc_out_en;
2423 llfc_enable = nig_params->llfc_enable;
2424 pause_enable = nig_params->pause_enable;
2425 } else /*defaul non PFC mode - PAUSE */
2426 pause_enable = 1;
2427
2428 xcm_mask |= (port ? NIG_LLH1_XCM_MASK_REG_LLH1_XCM_MASK_BCN :
2429 NIG_LLH0_XCM_MASK_REG_LLH0_XCM_MASK_BCN);
2430 xcm0_out_en = 1;
2431 }
2432
2433 if (CHIP_IS_E3(bp))
2434 REG_WR(bp, port ? NIG_REG_BRB1_PAUSE_IN_EN :
2435 NIG_REG_BRB0_PAUSE_IN_EN, pause_enable);
2436 REG_WR(bp, port ? NIG_REG_LLFC_OUT_EN_1 :
2437 NIG_REG_LLFC_OUT_EN_0, llfc_out_en);
2438 REG_WR(bp, port ? NIG_REG_LLFC_ENABLE_1 :
2439 NIG_REG_LLFC_ENABLE_0, llfc_enable);
2440 REG_WR(bp, port ? NIG_REG_PAUSE_ENABLE_1 :
2441 NIG_REG_PAUSE_ENABLE_0, pause_enable);
2442
2443 REG_WR(bp, port ? NIG_REG_PPP_ENABLE_1 :
2444 NIG_REG_PPP_ENABLE_0, ppp_enable);
2445
2446 REG_WR(bp, port ? NIG_REG_LLH1_XCM_MASK :
2447 NIG_REG_LLH0_XCM_MASK, xcm_mask);
2448
2449 REG_WR(bp, NIG_REG_LLFC_EGRESS_SRC_ENABLE_0, 0x7);
2450
2451 /* output enable for RX_XCM # IF */
2452 REG_WR(bp, NIG_REG_XCM0_OUT_EN, xcm0_out_en);
2453
2454 /* HW PFC TX enable */
2455 REG_WR(bp, NIG_REG_P0_HWPFC_ENABLE, p0_hwpfc_enable);
2456
2457 if (nig_params) {
2458 u8 i = 0;
2459 pkt_priority_to_cos = nig_params->pkt_priority_to_cos;
2460
2461 for (i = 0; i < nig_params->num_of_rx_cos_priority_mask; i++)
2462 bnx2x_pfc_nig_rx_priority_mask(bp, i,
2463 nig_params->rx_cos_priority_mask[i], port);
2464
2465 REG_WR(bp, port ? NIG_REG_LLFC_HIGH_PRIORITY_CLASSES_1 :
2466 NIG_REG_LLFC_HIGH_PRIORITY_CLASSES_0,
2467 nig_params->llfc_high_priority_classes);
2468
2469 REG_WR(bp, port ? NIG_REG_LLFC_LOW_PRIORITY_CLASSES_1 :
2470 NIG_REG_LLFC_LOW_PRIORITY_CLASSES_0,
2471 nig_params->llfc_low_priority_classes);
2472 }
2473 REG_WR(bp, port ? NIG_REG_P1_PKT_PRIORITY_TO_COS :
2474 NIG_REG_P0_PKT_PRIORITY_TO_COS,
2475 pkt_priority_to_cos);
2476 }
2477
2478 int bnx2x_update_pfc(struct link_params *params,
2479 struct link_vars *vars,
2480 struct bnx2x_nig_brb_pfc_port_params *pfc_params)
2481 {
2482 /*
2483 * The PFC and pause are orthogonal to one another, meaning when
2484 * PFC is enabled, the pause are disabled, and when PFC is
2485 * disabled, pause are set according to the pause result.
2486 */
2487 u32 val;
2488 struct bnx2x *bp = params->bp;
2489 int bnx2x_status = 0;
2490 u8 bmac_loopback = (params->loopback_mode == LOOPBACK_BMAC);
2491
2492 if (params->feature_config_flags & FEATURE_CONFIG_PFC_ENABLED)
2493 vars->link_status |= LINK_STATUS_PFC_ENABLED;
2494 else
2495 vars->link_status &= ~LINK_STATUS_PFC_ENABLED;
2496
2497 bnx2x_update_mng(params, vars->link_status);
2498
2499 /* update NIG params */
2500 bnx2x_update_pfc_nig(params, vars, pfc_params);
2501
2502 /* update BRB params */
2503 bnx2x_status = bnx2x_update_pfc_brb(params, vars, pfc_params);
2504 if (0 != bnx2x_status)
2505 return bnx2x_status;
2506
2507 if (!vars->link_up)
2508 return bnx2x_status;
2509
2510 DP(NETIF_MSG_LINK, "About to update PFC in BMAC\n");
2511 if (CHIP_IS_E3(bp))
2512 bnx2x_update_pfc_xmac(params, vars, 0);
2513 else {
2514 val = REG_RD(bp, MISC_REG_RESET_REG_2);
2515 if ((val &
2516 (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << params->port))
2517 == 0) {
2518 DP(NETIF_MSG_LINK, "About to update PFC in EMAC\n");
2519 bnx2x_emac_enable(params, vars, 0);
2520 return bnx2x_status;
2521 }
2522
2523 if (CHIP_IS_E2(bp))
2524 bnx2x_update_pfc_bmac2(params, vars, bmac_loopback);
2525 else
2526 bnx2x_update_pfc_bmac1(params, vars);
2527
2528 val = 0;
2529 if ((params->feature_config_flags &
2530 FEATURE_CONFIG_PFC_ENABLED) ||
2531 (vars->flow_ctrl & BNX2X_FLOW_CTRL_TX))
2532 val = 1;
2533 REG_WR(bp, NIG_REG_BMAC0_PAUSE_OUT_EN + params->port*4, val);
2534 }
2535 return bnx2x_status;
2536 }
2537
2538
2539 static int bnx2x_bmac1_enable(struct link_params *params,
2540 struct link_vars *vars,
2541 u8 is_lb)
2542 {
2543 struct bnx2x *bp = params->bp;
2544 u8 port = params->port;
2545 u32 bmac_addr = port ? NIG_REG_INGRESS_BMAC1_MEM :
2546 NIG_REG_INGRESS_BMAC0_MEM;
2547 u32 wb_data[2];
2548 u32 val;
2549
2550 DP(NETIF_MSG_LINK, "Enabling BigMAC1\n");
2551
2552 /* XGXS control */
2553 wb_data[0] = 0x3c;
2554 wb_data[1] = 0;
2555 REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_BMAC_XGXS_CONTROL,
2556 wb_data, 2);
2557
2558 /* tx MAC SA */
2559 wb_data[0] = ((params->mac_addr[2] << 24) |
2560 (params->mac_addr[3] << 16) |
2561 (params->mac_addr[4] << 8) |
2562 params->mac_addr[5]);
2563 wb_data[1] = ((params->mac_addr[0] << 8) |
2564 params->mac_addr[1]);
2565 REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_TX_SOURCE_ADDR, wb_data, 2);
2566
2567 /* mac control */
2568 val = 0x3;
2569 if (is_lb) {
2570 val |= 0x4;
2571 DP(NETIF_MSG_LINK, "enable bmac loopback\n");
2572 }
2573 wb_data[0] = val;
2574 wb_data[1] = 0;
2575 REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_BMAC_CONTROL, wb_data, 2);
2576
2577 /* set rx mtu */
2578 wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD;
2579 wb_data[1] = 0;
2580 REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_RX_MAX_SIZE, wb_data, 2);
2581
2582 bnx2x_update_pfc_bmac1(params, vars);
2583
2584 /* set tx mtu */
2585 wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD;
2586 wb_data[1] = 0;
2587 REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_TX_MAX_SIZE, wb_data, 2);
2588
2589 /* set cnt max size */
2590 wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD;
2591 wb_data[1] = 0;
2592 REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_CNT_MAX_SIZE, wb_data, 2);
2593
2594 /* configure safc */
2595 wb_data[0] = 0x1000200;
2596 wb_data[1] = 0;
2597 REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_RX_LLFC_MSG_FLDS,
2598 wb_data, 2);
2599
2600 return 0;
2601 }
2602
2603 static int bnx2x_bmac2_enable(struct link_params *params,
2604 struct link_vars *vars,
2605 u8 is_lb)
2606 {
2607 struct bnx2x *bp = params->bp;
2608 u8 port = params->port;
2609 u32 bmac_addr = port ? NIG_REG_INGRESS_BMAC1_MEM :
2610 NIG_REG_INGRESS_BMAC0_MEM;
2611 u32 wb_data[2];
2612
2613 DP(NETIF_MSG_LINK, "Enabling BigMAC2\n");
2614
2615 wb_data[0] = 0;
2616 wb_data[1] = 0;
2617 REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_BMAC_CONTROL, wb_data, 2);
2618 udelay(30);
2619
2620 /* XGXS control: Reset phy HW, MDIO registers, PHY PLL and BMAC */
2621 wb_data[0] = 0x3c;
2622 wb_data[1] = 0;
2623 REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_BMAC_XGXS_CONTROL,
2624 wb_data, 2);
2625
2626 udelay(30);
2627
2628 /* tx MAC SA */
2629 wb_data[0] = ((params->mac_addr[2] << 24) |
2630 (params->mac_addr[3] << 16) |
2631 (params->mac_addr[4] << 8) |
2632 params->mac_addr[5]);
2633 wb_data[1] = ((params->mac_addr[0] << 8) |
2634 params->mac_addr[1]);
2635 REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_TX_SOURCE_ADDR,
2636 wb_data, 2);
2637
2638 udelay(30);
2639
2640 /* Configure SAFC */
2641 wb_data[0] = 0x1000200;
2642 wb_data[1] = 0;
2643 REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_RX_LLFC_MSG_FLDS,
2644 wb_data, 2);
2645 udelay(30);
2646
2647 /* set rx mtu */
2648 wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD;
2649 wb_data[1] = 0;
2650 REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_RX_MAX_SIZE, wb_data, 2);
2651 udelay(30);
2652
2653 /* set tx mtu */
2654 wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD;
2655 wb_data[1] = 0;
2656 REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_TX_MAX_SIZE, wb_data, 2);
2657 udelay(30);
2658 /* set cnt max size */
2659 wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD - 2;
2660 wb_data[1] = 0;
2661 REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_CNT_MAX_SIZE, wb_data, 2);
2662 udelay(30);
2663 bnx2x_update_pfc_bmac2(params, vars, is_lb);
2664
2665 return 0;
2666 }
2667
2668 static int bnx2x_bmac_enable(struct link_params *params,
2669 struct link_vars *vars,
2670 u8 is_lb)
2671 {
2672 int rc = 0;
2673 u8 port = params->port;
2674 struct bnx2x *bp = params->bp;
2675 u32 val;
2676 /* reset and unreset the BigMac */
2677 REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR,
2678 (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
2679 msleep(1);
2680
2681 REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET,
2682 (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
2683
2684 /* enable access for bmac registers */
2685 REG_WR(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4, 0x1);
2686
2687 /* Enable BMAC according to BMAC type*/
2688 if (CHIP_IS_E2(bp))
2689 rc = bnx2x_bmac2_enable(params, vars, is_lb);
2690 else
2691 rc = bnx2x_bmac1_enable(params, vars, is_lb);
2692 REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL + port*4, 0x1);
2693 REG_WR(bp, NIG_REG_XGXS_LANE_SEL_P0 + port*4, 0x0);
2694 REG_WR(bp, NIG_REG_EGRESS_EMAC0_PORT + port*4, 0x0);
2695 val = 0;
2696 if ((params->feature_config_flags &
2697 FEATURE_CONFIG_PFC_ENABLED) ||
2698 (vars->flow_ctrl & BNX2X_FLOW_CTRL_TX))
2699 val = 1;
2700 REG_WR(bp, NIG_REG_BMAC0_PAUSE_OUT_EN + port*4, val);
2701 REG_WR(bp, NIG_REG_EGRESS_EMAC0_OUT_EN + port*4, 0x0);
2702 REG_WR(bp, NIG_REG_EMAC0_IN_EN + port*4, 0x0);
2703 REG_WR(bp, NIG_REG_EMAC0_PAUSE_OUT_EN + port*4, 0x0);
2704 REG_WR(bp, NIG_REG_BMAC0_IN_EN + port*4, 0x1);
2705 REG_WR(bp, NIG_REG_BMAC0_OUT_EN + port*4, 0x1);
2706
2707 vars->mac_type = MAC_TYPE_BMAC;
2708 return rc;
2709 }
2710
2711 static void bnx2x_bmac_rx_disable(struct bnx2x *bp, u8 port)
2712 {
2713 u32 bmac_addr = port ? NIG_REG_INGRESS_BMAC1_MEM :
2714 NIG_REG_INGRESS_BMAC0_MEM;
2715 u32 wb_data[2];
2716 u32 nig_bmac_enable = REG_RD(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4);
2717
2718 /* Only if the bmac is out of reset */
2719 if (REG_RD(bp, MISC_REG_RESET_REG_2) &
2720 (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port) &&
2721 nig_bmac_enable) {
2722
2723 if (CHIP_IS_E2(bp)) {
2724 /* Clear Rx Enable bit in BMAC_CONTROL register */
2725 REG_RD_DMAE(bp, bmac_addr +
2726 BIGMAC2_REGISTER_BMAC_CONTROL,
2727 wb_data, 2);
2728 wb_data[0] &= ~BMAC_CONTROL_RX_ENABLE;
2729 REG_WR_DMAE(bp, bmac_addr +
2730 BIGMAC2_REGISTER_BMAC_CONTROL,
2731 wb_data, 2);
2732 } else {
2733 /* Clear Rx Enable bit in BMAC_CONTROL register */
2734 REG_RD_DMAE(bp, bmac_addr +
2735 BIGMAC_REGISTER_BMAC_CONTROL,
2736 wb_data, 2);
2737 wb_data[0] &= ~BMAC_CONTROL_RX_ENABLE;
2738 REG_WR_DMAE(bp, bmac_addr +
2739 BIGMAC_REGISTER_BMAC_CONTROL,
2740 wb_data, 2);
2741 }
2742 msleep(1);
2743 }
2744 }
2745
2746 static int bnx2x_pbf_update(struct link_params *params, u32 flow_ctrl,
2747 u32 line_speed)
2748 {
2749 struct bnx2x *bp = params->bp;
2750 u8 port = params->port;
2751 u32 init_crd, crd;
2752 u32 count = 1000;
2753
2754 /* disable port */
2755 REG_WR(bp, PBF_REG_DISABLE_NEW_TASK_PROC_P0 + port*4, 0x1);
2756
2757 /* wait for init credit */
2758 init_crd = REG_RD(bp, PBF_REG_P0_INIT_CRD + port*4);
2759 crd = REG_RD(bp, PBF_REG_P0_CREDIT + port*8);
2760 DP(NETIF_MSG_LINK, "init_crd 0x%x crd 0x%x\n", init_crd, crd);
2761
2762 while ((init_crd != crd) && count) {
2763 msleep(5);
2764
2765 crd = REG_RD(bp, PBF_REG_P0_CREDIT + port*8);
2766 count--;
2767 }
2768 crd = REG_RD(bp, PBF_REG_P0_CREDIT + port*8);
2769 if (init_crd != crd) {
2770 DP(NETIF_MSG_LINK, "BUG! init_crd 0x%x != crd 0x%x\n",
2771 init_crd, crd);
2772 return -EINVAL;
2773 }
2774
2775 if (flow_ctrl & BNX2X_FLOW_CTRL_RX ||
2776 line_speed == SPEED_10 ||
2777 line_speed == SPEED_100 ||
2778 line_speed == SPEED_1000 ||
2779 line_speed == SPEED_2500) {
2780 REG_WR(bp, PBF_REG_P0_PAUSE_ENABLE + port*4, 1);
2781 /* update threshold */
2782 REG_WR(bp, PBF_REG_P0_ARB_THRSH + port*4, 0);
2783 /* update init credit */
2784 init_crd = 778; /* (800-18-4) */
2785
2786 } else {
2787 u32 thresh = (ETH_MAX_JUMBO_PACKET_SIZE +
2788 ETH_OVREHEAD)/16;
2789 REG_WR(bp, PBF_REG_P0_PAUSE_ENABLE + port*4, 0);
2790 /* update threshold */
2791 REG_WR(bp, PBF_REG_P0_ARB_THRSH + port*4, thresh);
2792 /* update init credit */
2793 switch (line_speed) {
2794 case SPEED_10000:
2795 init_crd = thresh + 553 - 22;
2796 break;
2797 default:
2798 DP(NETIF_MSG_LINK, "Invalid line_speed 0x%x\n",
2799 line_speed);
2800 return -EINVAL;
2801 }
2802 }
2803 REG_WR(bp, PBF_REG_P0_INIT_CRD + port*4, init_crd);
2804 DP(NETIF_MSG_LINK, "PBF updated to speed %d credit %d\n",
2805 line_speed, init_crd);
2806
2807 /* probe the credit changes */
2808 REG_WR(bp, PBF_REG_INIT_P0 + port*4, 0x1);
2809 msleep(5);
2810 REG_WR(bp, PBF_REG_INIT_P0 + port*4, 0x0);
2811
2812 /* enable port */
2813 REG_WR(bp, PBF_REG_DISABLE_NEW_TASK_PROC_P0 + port*4, 0x0);
2814 return 0;
2815 }
2816
2817 /**
2818 * bnx2x_get_emac_base - retrive emac base address
2819 *
2820 * @bp: driver handle
2821 * @mdc_mdio_access: access type
2822 * @port: port id
2823 *
2824 * This function selects the MDC/MDIO access (through emac0 or
2825 * emac1) depend on the mdc_mdio_access, port, port swapped. Each
2826 * phy has a default access mode, which could also be overridden
2827 * by nvram configuration. This parameter, whether this is the
2828 * default phy configuration, or the nvram overrun
2829 * configuration, is passed here as mdc_mdio_access and selects
2830 * the emac_base for the CL45 read/writes operations
2831 */
2832 static u32 bnx2x_get_emac_base(struct bnx2x *bp,
2833 u32 mdc_mdio_access, u8 port)
2834 {
2835 u32 emac_base = 0;
2836 switch (mdc_mdio_access) {
2837 case SHARED_HW_CFG_MDC_MDIO_ACCESS1_PHY_TYPE:
2838 break;
2839 case SHARED_HW_CFG_MDC_MDIO_ACCESS1_EMAC0:
2840 if (REG_RD(bp, NIG_REG_PORT_SWAP))
2841 emac_base = GRCBASE_EMAC1;
2842 else
2843 emac_base = GRCBASE_EMAC0;
2844 break;
2845 case SHARED_HW_CFG_MDC_MDIO_ACCESS1_EMAC1:
2846 if (REG_RD(bp, NIG_REG_PORT_SWAP))
2847 emac_base = GRCBASE_EMAC0;
2848 else
2849 emac_base = GRCBASE_EMAC1;
2850 break;
2851 case SHARED_HW_CFG_MDC_MDIO_ACCESS1_BOTH:
2852 emac_base = (port) ? GRCBASE_EMAC1 : GRCBASE_EMAC0;
2853 break;
2854 case SHARED_HW_CFG_MDC_MDIO_ACCESS1_SWAPPED:
2855 emac_base = (port) ? GRCBASE_EMAC0 : GRCBASE_EMAC1;
2856 break;
2857 default:
2858 break;
2859 }
2860 return emac_base;
2861
2862 }
2863
2864 /******************************************************************/
2865 /* CL22 access functions */
2866 /******************************************************************/
2867 static int bnx2x_cl22_write(struct bnx2x *bp,
2868 struct bnx2x_phy *phy,
2869 u16 reg, u16 val)
2870 {
2871 u32 tmp, mode;
2872 u8 i;
2873 int rc = 0;
2874 /* Switch to CL22 */
2875 mode = REG_RD(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE);
2876 REG_WR(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE,
2877 mode & ~EMAC_MDIO_MODE_CLAUSE_45);
2878
2879 /* address */
2880 tmp = ((phy->addr << 21) | (reg << 16) | val |
2881 EMAC_MDIO_COMM_COMMAND_WRITE_22 |
2882 EMAC_MDIO_COMM_START_BUSY);
2883 REG_WR(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM, tmp);
2884
2885 for (i = 0; i < 50; i++) {
2886 udelay(10);
2887
2888 tmp = REG_RD(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM);
2889 if (!(tmp & EMAC_MDIO_COMM_START_BUSY)) {
2890 udelay(5);
2891 break;
2892 }
2893 }
2894 if (tmp & EMAC_MDIO_COMM_START_BUSY) {
2895 DP(NETIF_MSG_LINK, "write phy register failed\n");
2896 rc = -EFAULT;
2897 }
2898 REG_WR(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE, mode);
2899 return rc;
2900 }
2901
2902 static int bnx2x_cl22_read(struct bnx2x *bp,
2903 struct bnx2x_phy *phy,
2904 u16 reg, u16 *ret_val)
2905 {
2906 u32 val, mode;
2907 u16 i;
2908 int rc = 0;
2909
2910 /* Switch to CL22 */
2911 mode = REG_RD(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE);
2912 REG_WR(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE,
2913 mode & ~EMAC_MDIO_MODE_CLAUSE_45);
2914
2915 /* address */
2916 val = ((phy->addr << 21) | (reg << 16) |
2917 EMAC_MDIO_COMM_COMMAND_READ_22 |
2918 EMAC_MDIO_COMM_START_BUSY);
2919 REG_WR(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM, val);
2920
2921 for (i = 0; i < 50; i++) {
2922 udelay(10);
2923
2924 val = REG_RD(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM);
2925 if (!(val & EMAC_MDIO_COMM_START_BUSY)) {
2926 *ret_val = (u16)(val & EMAC_MDIO_COMM_DATA);
2927 udelay(5);
2928 break;
2929 }
2930 }
2931 if (val & EMAC_MDIO_COMM_START_BUSY) {
2932 DP(NETIF_MSG_LINK, "read phy register failed\n");
2933
2934 *ret_val = 0;
2935 rc = -EFAULT;
2936 }
2937 REG_WR(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE, mode);
2938 return rc;
2939 }
2940
2941 /******************************************************************/
2942 /* CL45 access functions */
2943 /******************************************************************/
2944 static int bnx2x_cl45_read(struct bnx2x *bp, struct bnx2x_phy *phy,
2945 u8 devad, u16 reg, u16 *ret_val)
2946 {
2947 u32 val;
2948 u16 i;
2949 int rc = 0;
2950 if (phy->flags & FLAGS_MDC_MDIO_WA_B0)
2951 bnx2x_bits_en(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_STATUS,
2952 EMAC_MDIO_STATUS_10MB);
2953 /* address */
2954 val = ((phy->addr << 21) | (devad << 16) | reg |
2955 EMAC_MDIO_COMM_COMMAND_ADDRESS |
2956 EMAC_MDIO_COMM_START_BUSY);
2957 REG_WR(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM, val);
2958
2959 for (i = 0; i < 50; i++) {
2960 udelay(10);
2961
2962 val = REG_RD(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM);
2963 if (!(val & EMAC_MDIO_COMM_START_BUSY)) {
2964 udelay(5);
2965 break;
2966 }
2967 }
2968 if (val & EMAC_MDIO_COMM_START_BUSY) {
2969 DP(NETIF_MSG_LINK, "read phy register failed\n");
2970 netdev_err(bp->dev, "MDC/MDIO access timeout\n");
2971 *ret_val = 0;
2972 rc = -EFAULT;
2973 } else {
2974 /* data */
2975 val = ((phy->addr << 21) | (devad << 16) |
2976 EMAC_MDIO_COMM_COMMAND_READ_45 |
2977 EMAC_MDIO_COMM_START_BUSY);
2978 REG_WR(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM, val);
2979
2980 for (i = 0; i < 50; i++) {
2981 udelay(10);
2982
2983 val = REG_RD(bp, phy->mdio_ctrl +
2984 EMAC_REG_EMAC_MDIO_COMM);
2985 if (!(val & EMAC_MDIO_COMM_START_BUSY)) {
2986 *ret_val = (u16)(val & EMAC_MDIO_COMM_DATA);
2987 break;
2988 }
2989 }
2990 if (val & EMAC_MDIO_COMM_START_BUSY) {
2991 DP(NETIF_MSG_LINK, "read phy register failed\n");
2992 netdev_err(bp->dev, "MDC/MDIO access timeout\n");
2993 *ret_val = 0;
2994 rc = -EFAULT;
2995 }
2996 }
2997 /* Work around for E3 A0 */
2998 if (phy->flags & FLAGS_MDC_MDIO_WA) {
2999 phy->flags ^= FLAGS_DUMMY_READ;
3000 if (phy->flags & FLAGS_DUMMY_READ) {
3001 u16 temp_val;
3002 bnx2x_cl45_read(bp, phy, devad, 0xf, &temp_val);
3003 }
3004 }
3005
3006 if (phy->flags & FLAGS_MDC_MDIO_WA_B0)
3007 bnx2x_bits_dis(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_STATUS,
3008 EMAC_MDIO_STATUS_10MB);
3009 return rc;
3010 }
3011
3012 static int bnx2x_cl45_write(struct bnx2x *bp, struct bnx2x_phy *phy,
3013 u8 devad, u16 reg, u16 val)
3014 {
3015 u32 tmp;
3016 u8 i;
3017 int rc = 0;
3018 if (phy->flags & FLAGS_MDC_MDIO_WA_B0)
3019 bnx2x_bits_en(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_STATUS,
3020 EMAC_MDIO_STATUS_10MB);
3021
3022 /* address */
3023
3024 tmp = ((phy->addr << 21) | (devad << 16) | reg |
3025 EMAC_MDIO_COMM_COMMAND_ADDRESS |
3026 EMAC_MDIO_COMM_START_BUSY);
3027 REG_WR(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM, tmp);
3028
3029 for (i = 0; i < 50; i++) {
3030 udelay(10);
3031
3032 tmp = REG_RD(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM);
3033 if (!(tmp & EMAC_MDIO_COMM_START_BUSY)) {
3034 udelay(5);
3035 break;
3036 }
3037 }
3038 if (tmp & EMAC_MDIO_COMM_START_BUSY) {
3039 DP(NETIF_MSG_LINK, "write phy register failed\n");
3040 netdev_err(bp->dev, "MDC/MDIO access timeout\n");
3041 rc = -EFAULT;
3042
3043 } else {
3044 /* data */
3045 tmp = ((phy->addr << 21) | (devad << 16) | val |
3046 EMAC_MDIO_COMM_COMMAND_WRITE_45 |
3047 EMAC_MDIO_COMM_START_BUSY);
3048 REG_WR(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM, tmp);
3049
3050 for (i = 0; i < 50; i++) {
3051 udelay(10);
3052
3053 tmp = REG_RD(bp, phy->mdio_ctrl +
3054 EMAC_REG_EMAC_MDIO_COMM);
3055 if (!(tmp & EMAC_MDIO_COMM_START_BUSY)) {
3056 udelay(5);
3057 break;
3058 }
3059 }
3060 if (tmp & EMAC_MDIO_COMM_START_BUSY) {
3061 DP(NETIF_MSG_LINK, "write phy register failed\n");
3062 netdev_err(bp->dev, "MDC/MDIO access timeout\n");
3063 rc = -EFAULT;
3064 }
3065 }
3066 /* Work around for E3 A0 */
3067 if (phy->flags & FLAGS_MDC_MDIO_WA) {
3068 phy->flags ^= FLAGS_DUMMY_READ;
3069 if (phy->flags & FLAGS_DUMMY_READ) {
3070 u16 temp_val;
3071 bnx2x_cl45_read(bp, phy, devad, 0xf, &temp_val);
3072 }
3073 }
3074 if (phy->flags & FLAGS_MDC_MDIO_WA_B0)
3075 bnx2x_bits_dis(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_STATUS,
3076 EMAC_MDIO_STATUS_10MB);
3077 return rc;
3078 }
3079
3080
3081 /******************************************************************/
3082 /* BSC access functions from E3 */
3083 /******************************************************************/
3084 static void bnx2x_bsc_module_sel(struct link_params *params)
3085 {
3086 int idx;
3087 u32 board_cfg, sfp_ctrl;
3088 u32 i2c_pins[I2C_SWITCH_WIDTH], i2c_val[I2C_SWITCH_WIDTH];
3089 struct bnx2x *bp = params->bp;
3090 u8 port = params->port;
3091 /* Read I2C output PINs */
3092 board_cfg = REG_RD(bp, params->shmem_base +
3093 offsetof(struct shmem_region,
3094 dev_info.shared_hw_config.board));
3095 i2c_pins[I2C_BSC0] = board_cfg & SHARED_HW_CFG_E3_I2C_MUX0_MASK;
3096 i2c_pins[I2C_BSC1] = (board_cfg & SHARED_HW_CFG_E3_I2C_MUX1_MASK) >>
3097 SHARED_HW_CFG_E3_I2C_MUX1_SHIFT;
3098
3099 /* Read I2C output value */
3100 sfp_ctrl = REG_RD(bp, params->shmem_base +
3101 offsetof(struct shmem_region,
3102 dev_info.port_hw_config[port].e3_cmn_pin_cfg));
3103 i2c_val[I2C_BSC0] = (sfp_ctrl & PORT_HW_CFG_E3_I2C_MUX0_MASK) > 0;
3104 i2c_val[I2C_BSC1] = (sfp_ctrl & PORT_HW_CFG_E3_I2C_MUX1_MASK) > 0;
3105 DP(NETIF_MSG_LINK, "Setting BSC switch\n");
3106 for (idx = 0; idx < I2C_SWITCH_WIDTH; idx++)
3107 bnx2x_set_cfg_pin(bp, i2c_pins[idx], i2c_val[idx]);
3108 }
3109
3110 static int bnx2x_bsc_read(struct link_params *params,
3111 struct bnx2x_phy *phy,
3112 u8 sl_devid,
3113 u16 sl_addr,
3114 u8 lc_addr,
3115 u8 xfer_cnt,
3116 u32 *data_array)
3117 {
3118 u32 val, i;
3119 int rc = 0;
3120 struct bnx2x *bp = params->bp;
3121
3122 if ((sl_devid != 0xa0) && (sl_devid != 0xa2)) {
3123 DP(NETIF_MSG_LINK, "invalid sl_devid 0x%x\n", sl_devid);
3124 return -EINVAL;
3125 }
3126
3127 if (xfer_cnt > 16) {
3128 DP(NETIF_MSG_LINK, "invalid xfer_cnt %d. Max is 16 bytes\n",
3129 xfer_cnt);
3130 return -EINVAL;
3131 }
3132 bnx2x_bsc_module_sel(params);
3133
3134 xfer_cnt = 16 - lc_addr;
3135
3136 /* enable the engine */
3137 val = REG_RD(bp, MCP_REG_MCPR_IMC_COMMAND);
3138 val |= MCPR_IMC_COMMAND_ENABLE;
3139 REG_WR(bp, MCP_REG_MCPR_IMC_COMMAND, val);
3140
3141 /* program slave device ID */
3142 val = (sl_devid << 16) | sl_addr;
3143 REG_WR(bp, MCP_REG_MCPR_IMC_SLAVE_CONTROL, val);
3144
3145 /* start xfer with 0 byte to update the address pointer ???*/
3146 val = (MCPR_IMC_COMMAND_ENABLE) |
3147 (MCPR_IMC_COMMAND_WRITE_OP <<
3148 MCPR_IMC_COMMAND_OPERATION_BITSHIFT) |
3149 (lc_addr << MCPR_IMC_COMMAND_TRANSFER_ADDRESS_BITSHIFT) | (0);
3150 REG_WR(bp, MCP_REG_MCPR_IMC_COMMAND, val);
3151
3152 /* poll for completion */
3153 i = 0;
3154 val = REG_RD(bp, MCP_REG_MCPR_IMC_COMMAND);
3155 while (((val >> MCPR_IMC_COMMAND_IMC_STATUS_BITSHIFT) & 0x3) != 1) {
3156 udelay(10);
3157 val = REG_RD(bp, MCP_REG_MCPR_IMC_COMMAND);
3158 if (i++ > 1000) {
3159 DP(NETIF_MSG_LINK, "wr 0 byte timed out after %d try\n",
3160 i);
3161 rc = -EFAULT;
3162 break;
3163 }
3164 }
3165 if (rc == -EFAULT)
3166 return rc;
3167
3168 /* start xfer with read op */
3169 val = (MCPR_IMC_COMMAND_ENABLE) |
3170 (MCPR_IMC_COMMAND_READ_OP <<
3171 MCPR_IMC_COMMAND_OPERATION_BITSHIFT) |
3172 (lc_addr << MCPR_IMC_COMMAND_TRANSFER_ADDRESS_BITSHIFT) |
3173 (xfer_cnt);
3174 REG_WR(bp, MCP_REG_MCPR_IMC_COMMAND, val);
3175
3176 /* poll for completion */
3177 i = 0;
3178 val = REG_RD(bp, MCP_REG_MCPR_IMC_COMMAND);
3179 while (((val >> MCPR_IMC_COMMAND_IMC_STATUS_BITSHIFT) & 0x3) != 1) {
3180 udelay(10);
3181 val = REG_RD(bp, MCP_REG_MCPR_IMC_COMMAND);
3182 if (i++ > 1000) {
3183 DP(NETIF_MSG_LINK, "rd op timed out after %d try\n", i);
3184 rc = -EFAULT;
3185 break;
3186 }
3187 }
3188 if (rc == -EFAULT)
3189 return rc;
3190
3191 for (i = (lc_addr >> 2); i < 4; i++) {
3192 data_array[i] = REG_RD(bp, (MCP_REG_MCPR_IMC_DATAREG0 + i*4));
3193 #ifdef __BIG_ENDIAN
3194 data_array[i] = ((data_array[i] & 0x000000ff) << 24) |
3195 ((data_array[i] & 0x0000ff00) << 8) |
3196 ((data_array[i] & 0x00ff0000) >> 8) |
3197 ((data_array[i] & 0xff000000) >> 24);
3198 #endif
3199 }
3200 return rc;
3201 }
3202
3203 static void bnx2x_cl45_read_or_write(struct bnx2x *bp, struct bnx2x_phy *phy,
3204 u8 devad, u16 reg, u16 or_val)
3205 {
3206 u16 val;
3207 bnx2x_cl45_read(bp, phy, devad, reg, &val);
3208 bnx2x_cl45_write(bp, phy, devad, reg, val | or_val);
3209 }
3210
3211 int bnx2x_phy_read(struct link_params *params, u8 phy_addr,
3212 u8 devad, u16 reg, u16 *ret_val)
3213 {
3214 u8 phy_index;
3215 /*
3216 * Probe for the phy according to the given phy_addr, and execute
3217 * the read request on it
3218 */
3219 for (phy_index = 0; phy_index < params->num_phys; phy_index++) {
3220 if (params->phy[phy_index].addr == phy_addr) {
3221 return bnx2x_cl45_read(params->bp,
3222 &params->phy[phy_index], devad,
3223 reg, ret_val);
3224 }
3225 }
3226 return -EINVAL;
3227 }
3228
3229 int bnx2x_phy_write(struct link_params *params, u8 phy_addr,
3230 u8 devad, u16 reg, u16 val)
3231 {
3232 u8 phy_index;
3233 /*
3234 * Probe for the phy according to the given phy_addr, and execute
3235 * the write request on it
3236 */
3237 for (phy_index = 0; phy_index < params->num_phys; phy_index++) {
3238 if (params->phy[phy_index].addr == phy_addr) {
3239 return bnx2x_cl45_write(params->bp,
3240 &params->phy[phy_index], devad,
3241 reg, val);
3242 }
3243 }
3244 return -EINVAL;
3245 }
3246 static u8 bnx2x_get_warpcore_lane(struct bnx2x_phy *phy,
3247 struct link_params *params)
3248 {
3249 u8 lane = 0;
3250 struct bnx2x *bp = params->bp;
3251 u32 path_swap, path_swap_ovr;
3252 u8 path, port;
3253
3254 path = BP_PATH(bp);
3255 port = params->port;
3256
3257 if (bnx2x_is_4_port_mode(bp)) {
3258 u32 port_swap, port_swap_ovr;
3259
3260 /*figure out path swap value */
3261 path_swap_ovr = REG_RD(bp, MISC_REG_FOUR_PORT_PATH_SWAP_OVWR);
3262 if (path_swap_ovr & 0x1)
3263 path_swap = (path_swap_ovr & 0x2);
3264 else
3265 path_swap = REG_RD(bp, MISC_REG_FOUR_PORT_PATH_SWAP);
3266
3267 if (path_swap)
3268 path = path ^ 1;
3269
3270 /*figure out port swap value */
3271 port_swap_ovr = REG_RD(bp, MISC_REG_FOUR_PORT_PORT_SWAP_OVWR);
3272 if (port_swap_ovr & 0x1)
3273 port_swap = (port_swap_ovr & 0x2);
3274 else
3275 port_swap = REG_RD(bp, MISC_REG_FOUR_PORT_PORT_SWAP);
3276
3277 if (port_swap)
3278 port = port ^ 1;
3279
3280 lane = (port<<1) + path;
3281 } else { /* two port mode - no port swap */
3282
3283 /*figure out path swap value */
3284 path_swap_ovr =
3285 REG_RD(bp, MISC_REG_TWO_PORT_PATH_SWAP_OVWR);
3286 if (path_swap_ovr & 0x1) {
3287 path_swap = (path_swap_ovr & 0x2);
3288 } else {
3289 path_swap =
3290 REG_RD(bp, MISC_REG_TWO_PORT_PATH_SWAP);
3291 }
3292 if (path_swap)
3293 path = path ^ 1;
3294
3295 lane = path << 1 ;
3296 }
3297 return lane;
3298 }
3299
3300 static void bnx2x_set_aer_mmd(struct link_params *params,
3301 struct bnx2x_phy *phy)
3302 {
3303 u32 ser_lane;
3304 u16 offset, aer_val;
3305 struct bnx2x *bp = params->bp;
3306 ser_lane = ((params->lane_config &
3307 PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >>
3308 PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT);
3309
3310 offset = (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) ?
3311 (phy->addr + ser_lane) : 0;
3312
3313 if (USES_WARPCORE(bp)) {
3314 aer_val = bnx2x_get_warpcore_lane(phy, params);
3315 /*
3316 * In Dual-lane mode, two lanes are joined together,
3317 * so in order to configure them, the AER broadcast method is
3318 * used here.
3319 * 0x200 is the broadcast address for lanes 0,1
3320 * 0x201 is the broadcast address for lanes 2,3
3321 */
3322 if (phy->flags & FLAGS_WC_DUAL_MODE)
3323 aer_val = (aer_val >> 1) | 0x200;
3324 } else if (CHIP_IS_E2(bp))
3325 aer_val = 0x3800 + offset - 1;
3326 else
3327 aer_val = 0x3800 + offset;
3328 DP(NETIF_MSG_LINK, "Set AER to 0x%x\n", aer_val);
3329 CL22_WR_OVER_CL45(bp, phy, MDIO_REG_BANK_AER_BLOCK,
3330 MDIO_AER_BLOCK_AER_REG, aer_val);
3331
3332 }
3333
3334 /******************************************************************/
3335 /* Internal phy section */
3336 /******************************************************************/
3337
3338 static void bnx2x_set_serdes_access(struct bnx2x *bp, u8 port)
3339 {
3340 u32 emac_base = (port) ? GRCBASE_EMAC1 : GRCBASE_EMAC0;
3341
3342 /* Set Clause 22 */
3343 REG_WR(bp, NIG_REG_SERDES0_CTRL_MD_ST + port*0x10, 1);
3344 REG_WR(bp, emac_base + EMAC_REG_EMAC_MDIO_COMM, 0x245f8000);
3345 udelay(500);
3346 REG_WR(bp, emac_base + EMAC_REG_EMAC_MDIO_COMM, 0x245d000f);
3347 udelay(500);
3348 /* Set Clause 45 */
3349 REG_WR(bp, NIG_REG_SERDES0_CTRL_MD_ST + port*0x10, 0);
3350 }
3351
3352 static void bnx2x_serdes_deassert(struct bnx2x *bp, u8 port)
3353 {
3354 u32 val;
3355
3356 DP(NETIF_MSG_LINK, "bnx2x_serdes_deassert\n");
3357
3358 val = SERDES_RESET_BITS << (port*16);
3359
3360 /* reset and unreset the SerDes/XGXS */
3361 REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_CLEAR, val);
3362 udelay(500);
3363 REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_SET, val);
3364
3365 bnx2x_set_serdes_access(bp, port);
3366
3367 REG_WR(bp, NIG_REG_SERDES0_CTRL_MD_DEVAD + port*0x10,
3368 DEFAULT_PHY_DEV_ADDR);
3369 }
3370
3371 static void bnx2x_xgxs_deassert(struct link_params *params)
3372 {
3373 struct bnx2x *bp = params->bp;
3374 u8 port;
3375 u32 val;
3376 DP(NETIF_MSG_LINK, "bnx2x_xgxs_deassert\n");
3377 port = params->port;
3378
3379 val = XGXS_RESET_BITS << (port*16);
3380
3381 /* reset and unreset the SerDes/XGXS */
3382 REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_CLEAR, val);
3383 udelay(500);
3384 REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_SET, val);
3385
3386 REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_ST + port*0x18, 0);
3387 REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_DEVAD + port*0x18,
3388 params->phy[INT_PHY].def_md_devad);
3389 }
3390
3391 static void bnx2x_calc_ieee_aneg_adv(struct bnx2x_phy *phy,
3392 struct link_params *params, u16 *ieee_fc)
3393 {
3394 struct bnx2x *bp = params->bp;
3395 *ieee_fc = MDIO_COMBO_IEEE0_AUTO_NEG_ADV_FULL_DUPLEX;
3396 /**
3397 * resolve pause mode and advertisement Please refer to Table
3398 * 28B-3 of the 802.3ab-1999 spec
3399 */
3400
3401 switch (phy->req_flow_ctrl) {
3402 case BNX2X_FLOW_CTRL_AUTO:
3403 if (params->req_fc_auto_adv == BNX2X_FLOW_CTRL_BOTH)
3404 *ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH;
3405 else
3406 *ieee_fc |=
3407 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC;
3408 break;
3409
3410 case BNX2X_FLOW_CTRL_TX:
3411 *ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC;
3412 break;
3413
3414 case BNX2X_FLOW_CTRL_RX:
3415 case BNX2X_FLOW_CTRL_BOTH:
3416 *ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH;
3417 break;
3418
3419 case BNX2X_FLOW_CTRL_NONE:
3420 default:
3421 *ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_NONE;
3422 break;
3423 }
3424 DP(NETIF_MSG_LINK, "ieee_fc = 0x%x\n", *ieee_fc);
3425 }
3426
3427 static void set_phy_vars(struct link_params *params,
3428 struct link_vars *vars)
3429 {
3430 struct bnx2x *bp = params->bp;
3431 u8 actual_phy_idx, phy_index, link_cfg_idx;
3432 u8 phy_config_swapped = params->multi_phy_config &
3433 PORT_HW_CFG_PHY_SWAPPED_ENABLED;
3434 for (phy_index = INT_PHY; phy_index < params->num_phys;
3435 phy_index++) {
3436 link_cfg_idx = LINK_CONFIG_IDX(phy_index);
3437 actual_phy_idx = phy_index;
3438 if (phy_config_swapped) {
3439 if (phy_index == EXT_PHY1)
3440 actual_phy_idx = EXT_PHY2;
3441 else if (phy_index == EXT_PHY2)
3442 actual_phy_idx = EXT_PHY1;
3443 }
3444 params->phy[actual_phy_idx].req_flow_ctrl =
3445 params->req_flow_ctrl[link_cfg_idx];
3446
3447 params->phy[actual_phy_idx].req_line_speed =
3448 params->req_line_speed[link_cfg_idx];
3449
3450 params->phy[actual_phy_idx].speed_cap_mask =
3451 params->speed_cap_mask[link_cfg_idx];
3452
3453 params->phy[actual_phy_idx].req_duplex =
3454 params->req_duplex[link_cfg_idx];
3455
3456 if (params->req_line_speed[link_cfg_idx] ==
3457 SPEED_AUTO_NEG)
3458 vars->link_status |= LINK_STATUS_AUTO_NEGOTIATE_ENABLED;
3459
3460 DP(NETIF_MSG_LINK, "req_flow_ctrl %x, req_line_speed %x,"
3461 " speed_cap_mask %x\n",
3462 params->phy[actual_phy_idx].req_flow_ctrl,
3463 params->phy[actual_phy_idx].req_line_speed,
3464 params->phy[actual_phy_idx].speed_cap_mask);
3465 }
3466 }
3467
3468 static void bnx2x_ext_phy_set_pause(struct link_params *params,
3469 struct bnx2x_phy *phy,
3470 struct link_vars *vars)
3471 {
3472 u16 val;
3473 struct bnx2x *bp = params->bp;
3474 /* read modify write pause advertizing */
3475 bnx2x_cl45_read(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_ADV_PAUSE, &val);
3476
3477 val &= ~MDIO_AN_REG_ADV_PAUSE_BOTH;
3478
3479 /* Please refer to Table 28B-3 of 802.3ab-1999 spec. */
3480 bnx2x_calc_ieee_aneg_adv(phy, params, &vars->ieee_fc);
3481 if ((vars->ieee_fc &
3482 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) ==
3483 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) {
3484 val |= MDIO_AN_REG_ADV_PAUSE_ASYMMETRIC;
3485 }
3486 if ((vars->ieee_fc &
3487 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) ==
3488 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) {
3489 val |= MDIO_AN_REG_ADV_PAUSE_PAUSE;
3490 }
3491 DP(NETIF_MSG_LINK, "Ext phy AN advertize 0x%x\n", val);
3492 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_ADV_PAUSE, val);
3493 }
3494
3495 static void bnx2x_pause_resolve(struct link_vars *vars, u32 pause_result)
3496 { /* LD LP */
3497 switch (pause_result) { /* ASYM P ASYM P */
3498 case 0xb: /* 1 0 1 1 */
3499 vars->flow_ctrl = BNX2X_FLOW_CTRL_TX;
3500 break;
3501
3502 case 0xe: /* 1 1 1 0 */
3503 vars->flow_ctrl = BNX2X_FLOW_CTRL_RX;
3504 break;
3505
3506 case 0x5: /* 0 1 0 1 */
3507 case 0x7: /* 0 1 1 1 */
3508 case 0xd: /* 1 1 0 1 */
3509 case 0xf: /* 1 1 1 1 */
3510 vars->flow_ctrl = BNX2X_FLOW_CTRL_BOTH;
3511 break;
3512
3513 default:
3514 break;
3515 }
3516 if (pause_result & (1<<0))
3517 vars->link_status |= LINK_STATUS_LINK_PARTNER_SYMMETRIC_PAUSE;
3518 if (pause_result & (1<<1))
3519 vars->link_status |= LINK_STATUS_LINK_PARTNER_ASYMMETRIC_PAUSE;
3520 }
3521
3522 static u8 bnx2x_ext_phy_resolve_fc(struct bnx2x_phy *phy,
3523 struct link_params *params,
3524 struct link_vars *vars)
3525 {
3526 struct bnx2x *bp = params->bp;
3527 u16 ld_pause; /* local */
3528 u16 lp_pause; /* link partner */
3529 u16 pause_result;
3530 u8 ret = 0;
3531 /* read twice */
3532
3533 vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;
3534
3535 if (phy->req_flow_ctrl != BNX2X_FLOW_CTRL_AUTO)
3536 vars->flow_ctrl = phy->req_flow_ctrl;
3537 else if (phy->req_line_speed != SPEED_AUTO_NEG)
3538 vars->flow_ctrl = params->req_fc_auto_adv;
3539 else if (vars->link_status & LINK_STATUS_AUTO_NEGOTIATE_COMPLETE) {
3540 ret = 1;
3541 if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM54618SE) {
3542 bnx2x_cl22_read(bp, phy,
3543 0x4, &ld_pause);
3544 bnx2x_cl22_read(bp, phy,
3545 0x5, &lp_pause);
3546 } else {
3547 bnx2x_cl45_read(bp, phy,
3548 MDIO_AN_DEVAD,
3549 MDIO_AN_REG_ADV_PAUSE, &ld_pause);
3550 bnx2x_cl45_read(bp, phy,
3551 MDIO_AN_DEVAD,
3552 MDIO_AN_REG_LP_AUTO_NEG, &lp_pause);
3553 }
3554 pause_result = (ld_pause &
3555 MDIO_AN_REG_ADV_PAUSE_MASK) >> 8;
3556 pause_result |= (lp_pause &
3557 MDIO_AN_REG_ADV_PAUSE_MASK) >> 10;
3558 DP(NETIF_MSG_LINK, "Ext PHY pause result 0x%x\n",
3559 pause_result);
3560 bnx2x_pause_resolve(vars, pause_result);
3561 }
3562 return ret;
3563 }
3564 /******************************************************************/
3565 /* Warpcore section */
3566 /******************************************************************/
3567 /* The init_internal_warpcore should mirror the xgxs,
3568 * i.e. reset the lane (if needed), set aer for the
3569 * init configuration, and set/clear SGMII flag. Internal
3570 * phy init is done purely in phy_init stage.
3571 */
3572 static void bnx2x_warpcore_enable_AN_KR(struct bnx2x_phy *phy,
3573 struct link_params *params,
3574 struct link_vars *vars) {
3575 u16 val16 = 0, lane, bam37 = 0;
3576 struct bnx2x *bp = params->bp;
3577 DP(NETIF_MSG_LINK, "Enable Auto Negotiation for KR\n");
3578 /* Check adding advertisement for 1G KX */
3579 if (((vars->line_speed == SPEED_AUTO_NEG) &&
3580 (phy->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_1G)) ||
3581 (vars->line_speed == SPEED_1000)) {
3582 u16 sd_digital;
3583 val16 |= (1<<5);
3584
3585 /* Enable CL37 1G Parallel Detect */
3586 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
3587 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X2, &sd_digital);
3588 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3589 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X2,
3590 (sd_digital | 0x1));
3591
3592 DP(NETIF_MSG_LINK, "Advertize 1G\n");
3593 }
3594 if (((vars->line_speed == SPEED_AUTO_NEG) &&
3595 (phy->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)) ||
3596 (vars->line_speed == SPEED_10000)) {
3597 /* Check adding advertisement for 10G KR */
3598 val16 |= (1<<7);
3599 /* Enable 10G Parallel Detect */
3600 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD,
3601 MDIO_WC_REG_PAR_DET_10G_CTRL, 1);
3602
3603 DP(NETIF_MSG_LINK, "Advertize 10G\n");
3604 }
3605
3606 /* Set Transmit PMD settings */
3607 lane = bnx2x_get_warpcore_lane(phy, params);
3608 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3609 MDIO_WC_REG_TX0_TX_DRIVER + 0x10*lane,
3610 ((0x02 << MDIO_WC_REG_TX0_TX_DRIVER_POST2_COEFF_OFFSET) |
3611 (0x06 << MDIO_WC_REG_TX0_TX_DRIVER_IDRIVER_OFFSET) |
3612 (0x09 << MDIO_WC_REG_TX0_TX_DRIVER_IPRE_DRIVER_OFFSET)));
3613 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3614 MDIO_WC_REG_CL72_USERB0_CL72_OS_DEF_CTRL,
3615 0x03f0);
3616 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3617 MDIO_WC_REG_CL72_USERB0_CL72_2P5_DEF_CTRL,
3618 0x03f0);
3619 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3620 MDIO_WC_REG_CL72_USERB0_CL72_MISC1_CONTROL,
3621 0x383f);
3622
3623 /* Advertised speeds */
3624 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD,
3625 MDIO_WC_REG_AN_IEEE1BLK_AN_ADVERTISEMENT1, val16);
3626
3627 /* Advertised and set FEC (Forward Error Correction) */
3628 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD,
3629 MDIO_WC_REG_AN_IEEE1BLK_AN_ADVERTISEMENT2,
3630 (MDIO_WC_REG_AN_IEEE1BLK_AN_ADV2_FEC_ABILITY |
3631 MDIO_WC_REG_AN_IEEE1BLK_AN_ADV2_FEC_REQ));
3632
3633 /* Enable CL37 BAM */
3634 if (REG_RD(bp, params->shmem_base +
3635 offsetof(struct shmem_region, dev_info.
3636 port_hw_config[params->port].default_cfg)) &
3637 PORT_HW_CFG_ENABLE_BAM_ON_KR_ENABLED) {
3638 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
3639 MDIO_WC_REG_DIGITAL6_MP5_NEXTPAGECTRL, &bam37);
3640 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3641 MDIO_WC_REG_DIGITAL6_MP5_NEXTPAGECTRL, bam37 | 1);
3642 DP(NETIF_MSG_LINK, "Enable CL37 BAM on KR\n");
3643 }
3644
3645 /* Advertise pause */
3646 bnx2x_ext_phy_set_pause(params, phy, vars);
3647
3648 /* Enable Autoneg */
3649 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD,
3650 MDIO_WC_REG_IEEE0BLK_MIICNTL, 0x1000);
3651
3652 /* Over 1G - AN local device user page 1 */
3653 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3654 MDIO_WC_REG_DIGITAL3_UP1, 0x1f);
3655
3656 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
3657 MDIO_WC_REG_DIGITAL5_MISC7, &val16);
3658
3659 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3660 MDIO_WC_REG_DIGITAL5_MISC7, val16 | 0x100);
3661 }
3662
3663 static void bnx2x_warpcore_set_10G_KR(struct bnx2x_phy *phy,
3664 struct link_params *params,
3665 struct link_vars *vars)
3666 {
3667 struct bnx2x *bp = params->bp;
3668 u16 val;
3669
3670 /* Disable Autoneg */
3671 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3672 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X2, 0x7);
3673
3674 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD,
3675 MDIO_WC_REG_PAR_DET_10G_CTRL, 0);
3676
3677 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3678 MDIO_WC_REG_CL72_USERB0_CL72_MISC1_CONTROL, 0x3f00);
3679
3680 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD,
3681 MDIO_WC_REG_AN_IEEE1BLK_AN_ADVERTISEMENT1, 0);
3682
3683 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD,
3684 MDIO_WC_REG_IEEE0BLK_MIICNTL, 0x0);
3685
3686 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3687 MDIO_WC_REG_DIGITAL3_UP1, 0x1);
3688
3689 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3690 MDIO_WC_REG_DIGITAL5_MISC7, 0xa);
3691
3692 /* Disable CL36 PCS Tx */
3693 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3694 MDIO_WC_REG_XGXSBLK1_LANECTRL0, 0x0);
3695
3696 /* Double Wide Single Data Rate @ pll rate */
3697 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3698 MDIO_WC_REG_XGXSBLK1_LANECTRL1, 0xFFFF);
3699
3700 /* Leave cl72 training enable, needed for KR */
3701 bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD,
3702 MDIO_WC_REG_PMD_IEEE9BLK_TENGBASE_KR_PMD_CONTROL_REGISTER_150,
3703 0x2);
3704
3705 /* Leave CL72 enabled */
3706 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
3707 MDIO_WC_REG_CL72_USERB0_CL72_MISC1_CONTROL,
3708 &val);
3709 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3710 MDIO_WC_REG_CL72_USERB0_CL72_MISC1_CONTROL,
3711 val | 0x3800);
3712
3713 /* Set speed via PMA/PMD register */
3714 bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD,
3715 MDIO_WC_REG_IEEE0BLK_MIICNTL, 0x2040);
3716
3717 bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD,
3718 MDIO_WC_REG_IEEE0BLK_AUTONEGNP, 0xB);
3719
3720 /*Enable encoded forced speed */
3721 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3722 MDIO_WC_REG_SERDESDIGITAL_MISC2, 0x30);
3723
3724 /* Turn TX scramble payload only the 64/66 scrambler */
3725 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3726 MDIO_WC_REG_TX66_CONTROL, 0x9);
3727
3728 /* Turn RX scramble payload only the 64/66 scrambler */
3729 bnx2x_cl45_read_or_write(bp, phy, MDIO_WC_DEVAD,
3730 MDIO_WC_REG_RX66_CONTROL, 0xF9);
3731
3732 /* set and clear loopback to cause a reset to 64/66 decoder */
3733 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3734 MDIO_WC_REG_IEEE0BLK_MIICNTL, 0x4000);
3735 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3736 MDIO_WC_REG_IEEE0BLK_MIICNTL, 0x0);
3737
3738 }
3739
3740 static void bnx2x_warpcore_set_10G_XFI(struct bnx2x_phy *phy,
3741 struct link_params *params,
3742 u8 is_xfi)
3743 {
3744 struct bnx2x *bp = params->bp;
3745 u16 misc1_val, tap_val, tx_driver_val, lane, val;
3746 /* Hold rxSeqStart */
3747 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
3748 MDIO_WC_REG_DSC2B0_DSC_MISC_CTRL0, &val);
3749 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3750 MDIO_WC_REG_DSC2B0_DSC_MISC_CTRL0, (val | 0x8000));
3751
3752 /* Hold tx_fifo_reset */
3753 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
3754 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X3, &val);
3755 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3756 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X3, (val | 0x1));
3757
3758 /* Disable CL73 AN */
3759 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_CTRL, 0);
3760
3761 /* Disable 100FX Enable and Auto-Detect */
3762 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
3763 MDIO_WC_REG_FX100_CTRL1, &val);
3764 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3765 MDIO_WC_REG_FX100_CTRL1, (val & 0xFFFA));
3766
3767 /* Disable 100FX Idle detect */
3768 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
3769 MDIO_WC_REG_FX100_CTRL3, &val);
3770 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3771 MDIO_WC_REG_FX100_CTRL3, (val | 0x0080));
3772
3773 /* Set Block address to Remote PHY & Clear forced_speed[5] */
3774 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
3775 MDIO_WC_REG_DIGITAL4_MISC3, &val);
3776 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3777 MDIO_WC_REG_DIGITAL4_MISC3, (val & 0xFF7F));
3778
3779 /* Turn off auto-detect & fiber mode */
3780 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
3781 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X1, &val);
3782 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3783 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X1,
3784 (val & 0xFFEE));
3785
3786 /* Set filter_force_link, disable_false_link and parallel_detect */
3787 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
3788 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X2, &val);
3789 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3790 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X2,
3791 ((val | 0x0006) & 0xFFFE));
3792
3793 /* Set XFI / SFI */
3794 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
3795 MDIO_WC_REG_SERDESDIGITAL_MISC1, &misc1_val);
3796
3797 misc1_val &= ~(0x1f);
3798
3799 if (is_xfi) {
3800 misc1_val |= 0x5;
3801 tap_val = ((0x08 << MDIO_WC_REG_TX_FIR_TAP_POST_TAP_OFFSET) |
3802 (0x37 << MDIO_WC_REG_TX_FIR_TAP_MAIN_TAP_OFFSET) |
3803 (0x00 << MDIO_WC_REG_TX_FIR_TAP_PRE_TAP_OFFSET));
3804 tx_driver_val =
3805 ((0x00 << MDIO_WC_REG_TX0_TX_DRIVER_POST2_COEFF_OFFSET) |
3806 (0x02 << MDIO_WC_REG_TX0_TX_DRIVER_IDRIVER_OFFSET) |
3807 (0x03 << MDIO_WC_REG_TX0_TX_DRIVER_IPRE_DRIVER_OFFSET));
3808
3809 } else {
3810 misc1_val |= 0x9;
3811 tap_val = ((0x12 << MDIO_WC_REG_TX_FIR_TAP_POST_TAP_OFFSET) |
3812 (0x2d << MDIO_WC_REG_TX_FIR_TAP_MAIN_TAP_OFFSET) |
3813 (0x00 << MDIO_WC_REG_TX_FIR_TAP_PRE_TAP_OFFSET));
3814 tx_driver_val =
3815 ((0x02 << MDIO_WC_REG_TX0_TX_DRIVER_POST2_COEFF_OFFSET) |
3816 (0x02 << MDIO_WC_REG_TX0_TX_DRIVER_IDRIVER_OFFSET) |
3817 (0x02 << MDIO_WC_REG_TX0_TX_DRIVER_IPRE_DRIVER_OFFSET));
3818 }
3819 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3820 MDIO_WC_REG_SERDESDIGITAL_MISC1, misc1_val);
3821
3822 /* Set Transmit PMD settings */
3823 lane = bnx2x_get_warpcore_lane(phy, params);
3824 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3825 MDIO_WC_REG_TX_FIR_TAP,
3826 tap_val | MDIO_WC_REG_TX_FIR_TAP_ENABLE);
3827 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3828 MDIO_WC_REG_TX0_TX_DRIVER + 0x10*lane,
3829 tx_driver_val);
3830
3831 /* Enable fiber mode, enable and invert sig_det */
3832 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
3833 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X1, &val);
3834 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3835 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X1, val | 0xd);
3836
3837 /* Set Block address to Remote PHY & Set forced_speed[5], 40bit mode */
3838 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
3839 MDIO_WC_REG_DIGITAL4_MISC3, &val);
3840 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3841 MDIO_WC_REG_DIGITAL4_MISC3, val | 0x8080);
3842
3843 /* 10G XFI Full Duplex */
3844 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3845 MDIO_WC_REG_IEEE0BLK_MIICNTL, 0x100);
3846
3847 /* Release tx_fifo_reset */
3848 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
3849 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X3, &val);
3850 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3851 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X3, val & 0xFFFE);
3852
3853 /* Release rxSeqStart */
3854 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
3855 MDIO_WC_REG_DSC2B0_DSC_MISC_CTRL0, &val);
3856 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3857 MDIO_WC_REG_DSC2B0_DSC_MISC_CTRL0, (val & 0x7FFF));
3858 }
3859
3860 static void bnx2x_warpcore_set_20G_KR2(struct bnx2x *bp,
3861 struct bnx2x_phy *phy)
3862 {
3863 DP(NETIF_MSG_LINK, "KR2 still not supported !!!\n");
3864 }
3865
3866 static void bnx2x_warpcore_set_20G_DXGXS(struct bnx2x *bp,
3867 struct bnx2x_phy *phy,
3868 u16 lane)
3869 {
3870 /* Rx0 anaRxControl1G */
3871 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3872 MDIO_WC_REG_RX0_ANARXCONTROL1G, 0x90);
3873
3874 /* Rx2 anaRxControl1G */
3875 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3876 MDIO_WC_REG_RX2_ANARXCONTROL1G, 0x90);
3877
3878 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3879 MDIO_WC_REG_RX66_SCW0, 0xE070);
3880
3881 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3882 MDIO_WC_REG_RX66_SCW1, 0xC0D0);
3883
3884 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3885 MDIO_WC_REG_RX66_SCW2, 0xA0B0);
3886
3887 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3888 MDIO_WC_REG_RX66_SCW3, 0x8090);
3889
3890 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3891 MDIO_WC_REG_RX66_SCW0_MASK, 0xF0F0);
3892
3893 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3894 MDIO_WC_REG_RX66_SCW1_MASK, 0xF0F0);
3895
3896 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3897 MDIO_WC_REG_RX66_SCW2_MASK, 0xF0F0);
3898
3899 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3900 MDIO_WC_REG_RX66_SCW3_MASK, 0xF0F0);
3901
3902 /* Serdes Digital Misc1 */
3903 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3904 MDIO_WC_REG_SERDESDIGITAL_MISC1, 0x6008);
3905
3906 /* Serdes Digital4 Misc3 */
3907 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3908 MDIO_WC_REG_DIGITAL4_MISC3, 0x8088);
3909
3910 /* Set Transmit PMD settings */
3911 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3912 MDIO_WC_REG_TX_FIR_TAP,
3913 ((0x12 << MDIO_WC_REG_TX_FIR_TAP_POST_TAP_OFFSET) |
3914 (0x2d << MDIO_WC_REG_TX_FIR_TAP_MAIN_TAP_OFFSET) |
3915 (0x00 << MDIO_WC_REG_TX_FIR_TAP_PRE_TAP_OFFSET) |
3916 MDIO_WC_REG_TX_FIR_TAP_ENABLE));
3917 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3918 MDIO_WC_REG_TX0_TX_DRIVER + 0x10*lane,
3919 ((0x02 << MDIO_WC_REG_TX0_TX_DRIVER_POST2_COEFF_OFFSET) |
3920 (0x02 << MDIO_WC_REG_TX0_TX_DRIVER_IDRIVER_OFFSET) |
3921 (0x02 << MDIO_WC_REG_TX0_TX_DRIVER_IPRE_DRIVER_OFFSET)));
3922 }
3923
3924 static void bnx2x_warpcore_set_sgmii_speed(struct bnx2x_phy *phy,
3925 struct link_params *params,
3926 u8 fiber_mode)
3927 {
3928 struct bnx2x *bp = params->bp;
3929 u16 val16, digctrl_kx1, digctrl_kx2;
3930 u8 lane;
3931
3932 lane = bnx2x_get_warpcore_lane(phy, params);
3933
3934 /* Clear XFI clock comp in non-10G single lane mode. */
3935 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
3936 MDIO_WC_REG_RX66_CONTROL, &val16);
3937 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3938 MDIO_WC_REG_RX66_CONTROL, val16 & ~(3<<13));
3939
3940 if (phy->req_line_speed == SPEED_AUTO_NEG) {
3941 /* SGMII Autoneg */
3942 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
3943 MDIO_WC_REG_COMBO_IEEE0_MIICTRL, &val16);
3944 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3945 MDIO_WC_REG_COMBO_IEEE0_MIICTRL,
3946 val16 | 0x1000);
3947 DP(NETIF_MSG_LINK, "set SGMII AUTONEG\n");
3948 } else {
3949 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
3950 MDIO_WC_REG_COMBO_IEEE0_MIICTRL, &val16);
3951 val16 &= 0xcfbf;
3952 switch (phy->req_line_speed) {
3953 case SPEED_10:
3954 break;
3955 case SPEED_100:
3956 val16 |= 0x2000;
3957 break;
3958 case SPEED_1000:
3959 val16 |= 0x0040;
3960 break;
3961 default:
3962 DP(NETIF_MSG_LINK, "Speed not supported: 0x%x"
3963 "\n", phy->req_line_speed);
3964 return;
3965 }
3966
3967 if (phy->req_duplex == DUPLEX_FULL)
3968 val16 |= 0x0100;
3969
3970 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3971 MDIO_WC_REG_COMBO_IEEE0_MIICTRL, val16);
3972
3973 DP(NETIF_MSG_LINK, "set SGMII force speed %d\n",
3974 phy->req_line_speed);
3975 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
3976 MDIO_WC_REG_COMBO_IEEE0_MIICTRL, &val16);
3977 DP(NETIF_MSG_LINK, " (readback) %x\n", val16);
3978 }
3979
3980 /* SGMII Slave mode and disable signal detect */
3981 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
3982 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X1, &digctrl_kx1);
3983 if (fiber_mode)
3984 digctrl_kx1 = 1;
3985 else
3986 digctrl_kx1 &= 0xff4a;
3987
3988 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3989 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X1,
3990 digctrl_kx1);
3991
3992 /* Turn off parallel detect */
3993 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
3994 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X2, &digctrl_kx2);
3995 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
3996 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X2,
3997 (digctrl_kx2 & ~(1<<2)));
3998
3999 /* Re-enable parallel detect */
4000 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
4001 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X2,
4002 (digctrl_kx2 | (1<<2)));
4003
4004 /* Enable autodet */
4005 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
4006 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X1,
4007 (digctrl_kx1 | 0x10));
4008 }
4009
4010 static void bnx2x_warpcore_reset_lane(struct bnx2x *bp,
4011 struct bnx2x_phy *phy,
4012 u8 reset)
4013 {
4014 u16 val;
4015 /* Take lane out of reset after configuration is finished */
4016 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
4017 MDIO_WC_REG_DIGITAL5_MISC6, &val);
4018 if (reset)
4019 val |= 0xC000;
4020 else
4021 val &= 0x3FFF;
4022 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
4023 MDIO_WC_REG_DIGITAL5_MISC6, val);
4024 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
4025 MDIO_WC_REG_DIGITAL5_MISC6, &val);
4026 }
4027
4028
4029 /* Clear SFI/XFI link settings registers */
4030 static void bnx2x_warpcore_clear_regs(struct bnx2x_phy *phy,
4031 struct link_params *params,
4032 u16 lane)
4033 {
4034 struct bnx2x *bp = params->bp;
4035 u16 val16;
4036
4037 /* Set XFI clock comp as default. */
4038 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
4039 MDIO_WC_REG_RX66_CONTROL, &val16);
4040 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
4041 MDIO_WC_REG_RX66_CONTROL, val16 | (3<<13));
4042
4043 bnx2x_warpcore_reset_lane(bp, phy, 1);
4044 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_CTRL, 0);
4045 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
4046 MDIO_WC_REG_FX100_CTRL1, 0x014a);
4047 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
4048 MDIO_WC_REG_FX100_CTRL3, 0x0800);
4049 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
4050 MDIO_WC_REG_DIGITAL4_MISC3, 0x8008);
4051 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
4052 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X1, 0x0195);
4053 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
4054 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X2, 0x0007);
4055 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
4056 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X3, 0x0002);
4057 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
4058 MDIO_WC_REG_SERDESDIGITAL_MISC1, 0x6000);
4059 lane = bnx2x_get_warpcore_lane(phy, params);
4060 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
4061 MDIO_WC_REG_TX_FIR_TAP, 0x0000);
4062 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
4063 MDIO_WC_REG_TX0_TX_DRIVER + 0x10*lane, 0x0990);
4064 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
4065 MDIO_WC_REG_IEEE0BLK_MIICNTL, 0x2040);
4066 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
4067 MDIO_WC_REG_COMBO_IEEE0_MIICTRL, 0x0140);
4068 bnx2x_warpcore_reset_lane(bp, phy, 0);
4069 }
4070
4071 static int bnx2x_get_mod_abs_int_cfg(struct bnx2x *bp,
4072 u32 chip_id,
4073 u32 shmem_base, u8 port,
4074 u8 *gpio_num, u8 *gpio_port)
4075 {
4076 u32 cfg_pin;
4077 *gpio_num = 0;
4078 *gpio_port = 0;
4079 if (CHIP_IS_E3(bp)) {
4080 cfg_pin = (REG_RD(bp, shmem_base +
4081 offsetof(struct shmem_region,
4082 dev_info.port_hw_config[port].e3_sfp_ctrl)) &
4083 PORT_HW_CFG_E3_MOD_ABS_MASK) >>
4084 PORT_HW_CFG_E3_MOD_ABS_SHIFT;
4085
4086 /*
4087 * Should not happen. This function called upon interrupt
4088 * triggered by GPIO ( since EPIO can only generate interrupts
4089 * to MCP).
4090 * So if this function was called and none of the GPIOs was set,
4091 * it means the shit hit the fan.
4092 */
4093 if ((cfg_pin < PIN_CFG_GPIO0_P0) ||
4094 (cfg_pin > PIN_CFG_GPIO3_P1)) {
4095 DP(NETIF_MSG_LINK, "ERROR: Invalid cfg pin %x for "
4096 "module detect indication\n",
4097 cfg_pin);
4098 return -EINVAL;
4099 }
4100
4101 *gpio_num = (cfg_pin - PIN_CFG_GPIO0_P0) & 0x3;
4102 *gpio_port = (cfg_pin - PIN_CFG_GPIO0_P0) >> 2;
4103 } else {
4104 *gpio_num = MISC_REGISTERS_GPIO_3;
4105 *gpio_port = port;
4106 }
4107 DP(NETIF_MSG_LINK, "MOD_ABS int GPIO%d_P%d\n", *gpio_num, *gpio_port);
4108 return 0;
4109 }
4110
4111 static int bnx2x_is_sfp_module_plugged(struct bnx2x_phy *phy,
4112 struct link_params *params)
4113 {
4114 struct bnx2x *bp = params->bp;
4115 u8 gpio_num, gpio_port;
4116 u32 gpio_val;
4117 if (bnx2x_get_mod_abs_int_cfg(bp, params->chip_id,
4118 params->shmem_base, params->port,
4119 &gpio_num, &gpio_port) != 0)
4120 return 0;
4121 gpio_val = bnx2x_get_gpio(bp, gpio_num, gpio_port);
4122
4123 /* Call the handling function in case module is detected */
4124 if (gpio_val == 0)
4125 return 1;
4126 else
4127 return 0;
4128 }
4129
4130 static void bnx2x_warpcore_config_init(struct bnx2x_phy *phy,
4131 struct link_params *params,
4132 struct link_vars *vars)
4133 {
4134 struct bnx2x *bp = params->bp;
4135 u32 serdes_net_if;
4136 u8 fiber_mode;
4137 u16 lane = bnx2x_get_warpcore_lane(phy, params);
4138 serdes_net_if = (REG_RD(bp, params->shmem_base +
4139 offsetof(struct shmem_region, dev_info.
4140 port_hw_config[params->port].default_cfg)) &
4141 PORT_HW_CFG_NET_SERDES_IF_MASK);
4142 DP(NETIF_MSG_LINK, "Begin Warpcore init, link_speed %d, "
4143 "serdes_net_if = 0x%x\n",
4144 vars->line_speed, serdes_net_if);
4145 bnx2x_set_aer_mmd(params, phy);
4146
4147 vars->phy_flags |= PHY_XGXS_FLAG;
4148 if ((serdes_net_if == PORT_HW_CFG_NET_SERDES_IF_SGMII) ||
4149 (phy->req_line_speed &&
4150 ((phy->req_line_speed == SPEED_100) ||
4151 (phy->req_line_speed == SPEED_10)))) {
4152 vars->phy_flags |= PHY_SGMII_FLAG;
4153 DP(NETIF_MSG_LINK, "Setting SGMII mode\n");
4154 bnx2x_warpcore_clear_regs(phy, params, lane);
4155 bnx2x_warpcore_set_sgmii_speed(phy, params, 0);
4156 } else {
4157 switch (serdes_net_if) {
4158 case PORT_HW_CFG_NET_SERDES_IF_KR:
4159 /* Enable KR Auto Neg */
4160 if (params->loopback_mode == LOOPBACK_NONE)
4161 bnx2x_warpcore_enable_AN_KR(phy, params, vars);
4162 else {
4163 DP(NETIF_MSG_LINK, "Setting KR 10G-Force\n");
4164 bnx2x_warpcore_set_10G_KR(phy, params, vars);
4165 }
4166 break;
4167
4168 case PORT_HW_CFG_NET_SERDES_IF_XFI:
4169 bnx2x_warpcore_clear_regs(phy, params, lane);
4170 if (vars->line_speed == SPEED_10000) {
4171 DP(NETIF_MSG_LINK, "Setting 10G XFI\n");
4172 bnx2x_warpcore_set_10G_XFI(phy, params, 1);
4173 } else {
4174 if (SINGLE_MEDIA_DIRECT(params)) {
4175 DP(NETIF_MSG_LINK, "1G Fiber\n");
4176 fiber_mode = 1;
4177 } else {
4178 DP(NETIF_MSG_LINK, "10/100/1G SGMII\n");
4179 fiber_mode = 0;
4180 }
4181 bnx2x_warpcore_set_sgmii_speed(phy,
4182 params,
4183 fiber_mode);
4184 }
4185
4186 break;
4187
4188 case PORT_HW_CFG_NET_SERDES_IF_SFI:
4189
4190 bnx2x_warpcore_clear_regs(phy, params, lane);
4191 if (vars->line_speed == SPEED_10000) {
4192 DP(NETIF_MSG_LINK, "Setting 10G SFI\n");
4193 bnx2x_warpcore_set_10G_XFI(phy, params, 0);
4194 } else if (vars->line_speed == SPEED_1000) {
4195 DP(NETIF_MSG_LINK, "Setting 1G Fiber\n");
4196 bnx2x_warpcore_set_sgmii_speed(phy, params, 1);
4197 }
4198 /* Issue Module detection */
4199 if (bnx2x_is_sfp_module_plugged(phy, params))
4200 bnx2x_sfp_module_detection(phy, params);
4201 break;
4202
4203 case PORT_HW_CFG_NET_SERDES_IF_DXGXS:
4204 if (vars->line_speed != SPEED_20000) {
4205 DP(NETIF_MSG_LINK, "Speed not supported yet\n");
4206 return;
4207 }
4208 DP(NETIF_MSG_LINK, "Setting 20G DXGXS\n");
4209 bnx2x_warpcore_set_20G_DXGXS(bp, phy, lane);
4210 /* Issue Module detection */
4211
4212 bnx2x_sfp_module_detection(phy, params);
4213 break;
4214
4215 case PORT_HW_CFG_NET_SERDES_IF_KR2:
4216 if (vars->line_speed != SPEED_20000) {
4217 DP(NETIF_MSG_LINK, "Speed not supported yet\n");
4218 return;
4219 }
4220 DP(NETIF_MSG_LINK, "Setting 20G KR2\n");
4221 bnx2x_warpcore_set_20G_KR2(bp, phy);
4222 break;
4223
4224 default:
4225 DP(NETIF_MSG_LINK, "Unsupported Serdes Net Interface "
4226 "0x%x\n", serdes_net_if);
4227 return;
4228 }
4229 }
4230
4231 /* Take lane out of reset after configuration is finished */
4232 bnx2x_warpcore_reset_lane(bp, phy, 0);
4233 DP(NETIF_MSG_LINK, "Exit config init\n");
4234 }
4235
4236 static void bnx2x_sfp_e3_set_transmitter(struct link_params *params,
4237 struct bnx2x_phy *phy,
4238 u8 tx_en)
4239 {
4240 struct bnx2x *bp = params->bp;
4241 u32 cfg_pin;
4242 u8 port = params->port;
4243
4244 cfg_pin = REG_RD(bp, params->shmem_base +
4245 offsetof(struct shmem_region,
4246 dev_info.port_hw_config[port].e3_sfp_ctrl)) &
4247 PORT_HW_CFG_TX_LASER_MASK;
4248 /* Set the !tx_en since this pin is DISABLE_TX_LASER */
4249 DP(NETIF_MSG_LINK, "Setting WC TX to %d\n", tx_en);
4250 /* For 20G, the expected pin to be used is 3 pins after the current */
4251
4252 bnx2x_set_cfg_pin(bp, cfg_pin, tx_en ^ 1);
4253 if (phy->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_20G)
4254 bnx2x_set_cfg_pin(bp, cfg_pin + 3, tx_en ^ 1);
4255 }
4256
4257 static void bnx2x_warpcore_link_reset(struct bnx2x_phy *phy,
4258 struct link_params *params)
4259 {
4260 struct bnx2x *bp = params->bp;
4261 u16 val16;
4262 bnx2x_sfp_e3_set_transmitter(params, phy, 0);
4263 bnx2x_set_mdio_clk(bp, params->chip_id, params->port);
4264 bnx2x_set_aer_mmd(params, phy);
4265 /* Global register */
4266 bnx2x_warpcore_reset_lane(bp, phy, 1);
4267
4268 /* Clear loopback settings (if any) */
4269 /* 10G & 20G */
4270 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
4271 MDIO_WC_REG_COMBO_IEEE0_MIICTRL, &val16);
4272 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
4273 MDIO_WC_REG_COMBO_IEEE0_MIICTRL, val16 &
4274 0xBFFF);
4275
4276 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
4277 MDIO_WC_REG_IEEE0BLK_MIICNTL, &val16);
4278 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
4279 MDIO_WC_REG_IEEE0BLK_MIICNTL, val16 & 0xfffe);
4280
4281 /* Update those 1-copy registers */
4282 CL22_WR_OVER_CL45(bp, phy, MDIO_REG_BANK_AER_BLOCK,
4283 MDIO_AER_BLOCK_AER_REG, 0);
4284 /* Enable 1G MDIO (1-copy) */
4285 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
4286 MDIO_WC_REG_XGXSBLK0_XGXSCONTROL,
4287 &val16);
4288 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
4289 MDIO_WC_REG_XGXSBLK0_XGXSCONTROL,
4290 val16 & ~0x10);
4291
4292 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
4293 MDIO_WC_REG_XGXSBLK1_LANECTRL2, &val16);
4294 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
4295 MDIO_WC_REG_XGXSBLK1_LANECTRL2,
4296 val16 & 0xff00);
4297
4298 }
4299
4300 static void bnx2x_set_warpcore_loopback(struct bnx2x_phy *phy,
4301 struct link_params *params)
4302 {
4303 struct bnx2x *bp = params->bp;
4304 u16 val16;
4305 u32 lane;
4306 DP(NETIF_MSG_LINK, "Setting Warpcore loopback type %x, speed %d\n",
4307 params->loopback_mode, phy->req_line_speed);
4308
4309 if (phy->req_line_speed < SPEED_10000) {
4310 /* 10/100/1000 */
4311
4312 /* Update those 1-copy registers */
4313 CL22_WR_OVER_CL45(bp, phy, MDIO_REG_BANK_AER_BLOCK,
4314 MDIO_AER_BLOCK_AER_REG, 0);
4315 /* Enable 1G MDIO (1-copy) */
4316 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
4317 MDIO_WC_REG_XGXSBLK0_XGXSCONTROL,
4318 &val16);
4319 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
4320 MDIO_WC_REG_XGXSBLK0_XGXSCONTROL,
4321 val16 | 0x10);
4322 /* Set 1G loopback based on lane (1-copy) */
4323 lane = bnx2x_get_warpcore_lane(phy, params);
4324 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
4325 MDIO_WC_REG_XGXSBLK1_LANECTRL2, &val16);
4326 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
4327 MDIO_WC_REG_XGXSBLK1_LANECTRL2,
4328 val16 | (1<<lane));
4329
4330 /* Switch back to 4-copy registers */
4331 bnx2x_set_aer_mmd(params, phy);
4332 /* Global loopback, not recommended. */
4333 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
4334 MDIO_WC_REG_COMBO_IEEE0_MIICTRL, &val16);
4335 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
4336 MDIO_WC_REG_COMBO_IEEE0_MIICTRL, val16 |
4337 0x4000);
4338 } else {
4339 /* 10G & 20G */
4340 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
4341 MDIO_WC_REG_COMBO_IEEE0_MIICTRL, &val16);
4342 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
4343 MDIO_WC_REG_COMBO_IEEE0_MIICTRL, val16 |
4344 0x4000);
4345
4346 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
4347 MDIO_WC_REG_IEEE0BLK_MIICNTL, &val16);
4348 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
4349 MDIO_WC_REG_IEEE0BLK_MIICNTL, val16 | 0x1);
4350 }
4351 }
4352
4353
4354 void bnx2x_link_status_update(struct link_params *params,
4355 struct link_vars *vars)
4356 {
4357 struct bnx2x *bp = params->bp;
4358 u8 link_10g_plus;
4359 u8 port = params->port;
4360 u32 sync_offset, media_types;
4361 /* Update PHY configuration */
4362 set_phy_vars(params, vars);
4363
4364 vars->link_status = REG_RD(bp, params->shmem_base +
4365 offsetof(struct shmem_region,
4366 port_mb[port].link_status));
4367
4368 vars->link_up = (vars->link_status & LINK_STATUS_LINK_UP);
4369 vars->phy_flags = PHY_XGXS_FLAG;
4370 if (vars->link_status & LINK_STATUS_PHYSICAL_LINK_FLAG)
4371 vars->phy_flags |= PHY_PHYSICAL_LINK_FLAG;
4372
4373 if (vars->link_up) {
4374 DP(NETIF_MSG_LINK, "phy link up\n");
4375
4376 vars->phy_link_up = 1;
4377 vars->duplex = DUPLEX_FULL;
4378 switch (vars->link_status &
4379 LINK_STATUS_SPEED_AND_DUPLEX_MASK) {
4380 case LINK_10THD:
4381 vars->duplex = DUPLEX_HALF;
4382 /* fall thru */
4383 case LINK_10TFD:
4384 vars->line_speed = SPEED_10;
4385 break;
4386
4387 case LINK_100TXHD:
4388 vars->duplex = DUPLEX_HALF;
4389 /* fall thru */
4390 case LINK_100T4:
4391 case LINK_100TXFD:
4392 vars->line_speed = SPEED_100;
4393 break;
4394
4395 case LINK_1000THD:
4396 vars->duplex = DUPLEX_HALF;
4397 /* fall thru */
4398 case LINK_1000TFD:
4399 vars->line_speed = SPEED_1000;
4400 break;
4401
4402 case LINK_2500THD:
4403 vars->duplex = DUPLEX_HALF;
4404 /* fall thru */
4405 case LINK_2500TFD:
4406 vars->line_speed = SPEED_2500;
4407 break;
4408
4409 case LINK_10GTFD:
4410 vars->line_speed = SPEED_10000;
4411 break;
4412 case LINK_20GTFD:
4413 vars->line_speed = SPEED_20000;
4414 break;
4415 default:
4416 break;
4417 }
4418 vars->flow_ctrl = 0;
4419 if (vars->link_status & LINK_STATUS_TX_FLOW_CONTROL_ENABLED)
4420 vars->flow_ctrl |= BNX2X_FLOW_CTRL_TX;
4421
4422 if (vars->link_status & LINK_STATUS_RX_FLOW_CONTROL_ENABLED)
4423 vars->flow_ctrl |= BNX2X_FLOW_CTRL_RX;
4424
4425 if (!vars->flow_ctrl)
4426 vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;
4427
4428 if (vars->line_speed &&
4429 ((vars->line_speed == SPEED_10) ||
4430 (vars->line_speed == SPEED_100))) {
4431 vars->phy_flags |= PHY_SGMII_FLAG;
4432 } else {
4433 vars->phy_flags &= ~PHY_SGMII_FLAG;
4434 }
4435 if (vars->line_speed &&
4436 USES_WARPCORE(bp) &&
4437 (vars->line_speed == SPEED_1000))
4438 vars->phy_flags |= PHY_SGMII_FLAG;
4439 /* anything 10 and over uses the bmac */
4440 link_10g_plus = (vars->line_speed >= SPEED_10000);
4441
4442 if (link_10g_plus) {
4443 if (USES_WARPCORE(bp))
4444 vars->mac_type = MAC_TYPE_XMAC;
4445 else
4446 vars->mac_type = MAC_TYPE_BMAC;
4447 } else {
4448 if (USES_WARPCORE(bp))
4449 vars->mac_type = MAC_TYPE_UMAC;
4450 else
4451 vars->mac_type = MAC_TYPE_EMAC;
4452 }
4453 } else { /* link down */
4454 DP(NETIF_MSG_LINK, "phy link down\n");
4455
4456 vars->phy_link_up = 0;
4457
4458 vars->line_speed = 0;
4459 vars->duplex = DUPLEX_FULL;
4460 vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;
4461
4462 /* indicate no mac active */
4463 vars->mac_type = MAC_TYPE_NONE;
4464 if (vars->link_status & LINK_STATUS_PHYSICAL_LINK_FLAG)
4465 vars->phy_flags |= PHY_HALF_OPEN_CONN_FLAG;
4466 }
4467
4468 /* Sync media type */
4469 sync_offset = params->shmem_base +
4470 offsetof(struct shmem_region,
4471 dev_info.port_hw_config[port].media_type);
4472 media_types = REG_RD(bp, sync_offset);
4473
4474 params->phy[INT_PHY].media_type =
4475 (media_types & PORT_HW_CFG_MEDIA_TYPE_PHY0_MASK) >>
4476 PORT_HW_CFG_MEDIA_TYPE_PHY0_SHIFT;
4477 params->phy[EXT_PHY1].media_type =
4478 (media_types & PORT_HW_CFG_MEDIA_TYPE_PHY1_MASK) >>
4479 PORT_HW_CFG_MEDIA_TYPE_PHY1_SHIFT;
4480 params->phy[EXT_PHY2].media_type =
4481 (media_types & PORT_HW_CFG_MEDIA_TYPE_PHY2_MASK) >>
4482 PORT_HW_CFG_MEDIA_TYPE_PHY2_SHIFT;
4483 DP(NETIF_MSG_LINK, "media_types = 0x%x\n", media_types);
4484
4485 /* Sync AEU offset */
4486 sync_offset = params->shmem_base +
4487 offsetof(struct shmem_region,
4488 dev_info.port_hw_config[port].aeu_int_mask);
4489
4490 vars->aeu_int_mask = REG_RD(bp, sync_offset);
4491
4492 /* Sync PFC status */
4493 if (vars->link_status & LINK_STATUS_PFC_ENABLED)
4494 params->feature_config_flags |=
4495 FEATURE_CONFIG_PFC_ENABLED;
4496 else
4497 params->feature_config_flags &=
4498 ~FEATURE_CONFIG_PFC_ENABLED;
4499
4500 DP(NETIF_MSG_LINK, "link_status 0x%x phy_link_up %x int_mask 0x%x\n",
4501 vars->link_status, vars->phy_link_up, vars->aeu_int_mask);
4502 DP(NETIF_MSG_LINK, "line_speed %x duplex %x flow_ctrl 0x%x\n",
4503 vars->line_speed, vars->duplex, vars->flow_ctrl);
4504 }
4505
4506
4507 static void bnx2x_set_master_ln(struct link_params *params,
4508 struct bnx2x_phy *phy)
4509 {
4510 struct bnx2x *bp = params->bp;
4511 u16 new_master_ln, ser_lane;
4512 ser_lane = ((params->lane_config &
4513 PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >>
4514 PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT);
4515
4516 /* set the master_ln for AN */
4517 CL22_RD_OVER_CL45(bp, phy,
4518 MDIO_REG_BANK_XGXS_BLOCK2,
4519 MDIO_XGXS_BLOCK2_TEST_MODE_LANE,
4520 &new_master_ln);
4521
4522 CL22_WR_OVER_CL45(bp, phy,
4523 MDIO_REG_BANK_XGXS_BLOCK2 ,
4524 MDIO_XGXS_BLOCK2_TEST_MODE_LANE,
4525 (new_master_ln | ser_lane));
4526 }
4527
4528 static int bnx2x_reset_unicore(struct link_params *params,
4529 struct bnx2x_phy *phy,
4530 u8 set_serdes)
4531 {
4532 struct bnx2x *bp = params->bp;
4533 u16 mii_control;
4534 u16 i;
4535 CL22_RD_OVER_CL45(bp, phy,
4536 MDIO_REG_BANK_COMBO_IEEE0,
4537 MDIO_COMBO_IEEE0_MII_CONTROL, &mii_control);
4538
4539 /* reset the unicore */
4540 CL22_WR_OVER_CL45(bp, phy,
4541 MDIO_REG_BANK_COMBO_IEEE0,
4542 MDIO_COMBO_IEEE0_MII_CONTROL,
4543 (mii_control |
4544 MDIO_COMBO_IEEO_MII_CONTROL_RESET));
4545 if (set_serdes)
4546 bnx2x_set_serdes_access(bp, params->port);
4547
4548 /* wait for the reset to self clear */
4549 for (i = 0; i < MDIO_ACCESS_TIMEOUT; i++) {
4550 udelay(5);
4551
4552 /* the reset erased the previous bank value */
4553 CL22_RD_OVER_CL45(bp, phy,
4554 MDIO_REG_BANK_COMBO_IEEE0,
4555 MDIO_COMBO_IEEE0_MII_CONTROL,
4556 &mii_control);
4557
4558 if (!(mii_control & MDIO_COMBO_IEEO_MII_CONTROL_RESET)) {
4559 udelay(5);
4560 return 0;
4561 }
4562 }
4563
4564 netdev_err(bp->dev, "Warning: PHY was not initialized,"
4565 " Port %d\n",
4566 params->port);
4567 DP(NETIF_MSG_LINK, "BUG! XGXS is still in reset!\n");
4568 return -EINVAL;
4569
4570 }
4571
4572 static void bnx2x_set_swap_lanes(struct link_params *params,
4573 struct bnx2x_phy *phy)
4574 {
4575 struct bnx2x *bp = params->bp;
4576 /*
4577 * Each two bits represents a lane number:
4578 * No swap is 0123 => 0x1b no need to enable the swap
4579 */
4580 u16 ser_lane, rx_lane_swap, tx_lane_swap;
4581
4582 ser_lane = ((params->lane_config &
4583 PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >>
4584 PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT);
4585 rx_lane_swap = ((params->lane_config &
4586 PORT_HW_CFG_LANE_SWAP_CFG_RX_MASK) >>
4587 PORT_HW_CFG_LANE_SWAP_CFG_RX_SHIFT);
4588 tx_lane_swap = ((params->lane_config &
4589 PORT_HW_CFG_LANE_SWAP_CFG_TX_MASK) >>
4590 PORT_HW_CFG_LANE_SWAP_CFG_TX_SHIFT);
4591
4592 if (rx_lane_swap != 0x1b) {
4593 CL22_WR_OVER_CL45(bp, phy,
4594 MDIO_REG_BANK_XGXS_BLOCK2,
4595 MDIO_XGXS_BLOCK2_RX_LN_SWAP,
4596 (rx_lane_swap |
4597 MDIO_XGXS_BLOCK2_RX_LN_SWAP_ENABLE |
4598 MDIO_XGXS_BLOCK2_RX_LN_SWAP_FORCE_ENABLE));
4599 } else {
4600 CL22_WR_OVER_CL45(bp, phy,
4601 MDIO_REG_BANK_XGXS_BLOCK2,
4602 MDIO_XGXS_BLOCK2_RX_LN_SWAP, 0);
4603 }
4604
4605 if (tx_lane_swap != 0x1b) {
4606 CL22_WR_OVER_CL45(bp, phy,
4607 MDIO_REG_BANK_XGXS_BLOCK2,
4608 MDIO_XGXS_BLOCK2_TX_LN_SWAP,
4609 (tx_lane_swap |
4610 MDIO_XGXS_BLOCK2_TX_LN_SWAP_ENABLE));
4611 } else {
4612 CL22_WR_OVER_CL45(bp, phy,
4613 MDIO_REG_BANK_XGXS_BLOCK2,
4614 MDIO_XGXS_BLOCK2_TX_LN_SWAP, 0);
4615 }
4616 }
4617
4618 static void bnx2x_set_parallel_detection(struct bnx2x_phy *phy,
4619 struct link_params *params)
4620 {
4621 struct bnx2x *bp = params->bp;
4622 u16 control2;
4623 CL22_RD_OVER_CL45(bp, phy,
4624 MDIO_REG_BANK_SERDES_DIGITAL,
4625 MDIO_SERDES_DIGITAL_A_1000X_CONTROL2,
4626 &control2);
4627 if (phy->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_1G)
4628 control2 |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL2_PRL_DT_EN;
4629 else
4630 control2 &= ~MDIO_SERDES_DIGITAL_A_1000X_CONTROL2_PRL_DT_EN;
4631 DP(NETIF_MSG_LINK, "phy->speed_cap_mask = 0x%x, control2 = 0x%x\n",
4632 phy->speed_cap_mask, control2);
4633 CL22_WR_OVER_CL45(bp, phy,
4634 MDIO_REG_BANK_SERDES_DIGITAL,
4635 MDIO_SERDES_DIGITAL_A_1000X_CONTROL2,
4636 control2);
4637
4638 if ((phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) &&
4639 (phy->speed_cap_mask &
4640 PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)) {
4641 DP(NETIF_MSG_LINK, "XGXS\n");
4642
4643 CL22_WR_OVER_CL45(bp, phy,
4644 MDIO_REG_BANK_10G_PARALLEL_DETECT,
4645 MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_LINK,
4646 MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_LINK_CNT);
4647
4648 CL22_RD_OVER_CL45(bp, phy,
4649 MDIO_REG_BANK_10G_PARALLEL_DETECT,
4650 MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL,
4651 &control2);
4652
4653
4654 control2 |=
4655 MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL_PARDET10G_EN;
4656
4657 CL22_WR_OVER_CL45(bp, phy,
4658 MDIO_REG_BANK_10G_PARALLEL_DETECT,
4659 MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL,
4660 control2);
4661
4662 /* Disable parallel detection of HiG */
4663 CL22_WR_OVER_CL45(bp, phy,
4664 MDIO_REG_BANK_XGXS_BLOCK2,
4665 MDIO_XGXS_BLOCK2_UNICORE_MODE_10G,
4666 MDIO_XGXS_BLOCK2_UNICORE_MODE_10G_CX4_XGXS |
4667 MDIO_XGXS_BLOCK2_UNICORE_MODE_10G_HIGIG_XGXS);
4668 }
4669 }
4670
4671 static void bnx2x_set_autoneg(struct bnx2x_phy *phy,
4672 struct link_params *params,
4673 struct link_vars *vars,
4674 u8 enable_cl73)
4675 {
4676 struct bnx2x *bp = params->bp;
4677 u16 reg_val;
4678
4679 /* CL37 Autoneg */
4680 CL22_RD_OVER_CL45(bp, phy,
4681 MDIO_REG_BANK_COMBO_IEEE0,
4682 MDIO_COMBO_IEEE0_MII_CONTROL, &reg_val);
4683
4684 /* CL37 Autoneg Enabled */
4685 if (vars->line_speed == SPEED_AUTO_NEG)
4686 reg_val |= MDIO_COMBO_IEEO_MII_CONTROL_AN_EN;
4687 else /* CL37 Autoneg Disabled */
4688 reg_val &= ~(MDIO_COMBO_IEEO_MII_CONTROL_AN_EN |
4689 MDIO_COMBO_IEEO_MII_CONTROL_RESTART_AN);
4690
4691 CL22_WR_OVER_CL45(bp, phy,
4692 MDIO_REG_BANK_COMBO_IEEE0,
4693 MDIO_COMBO_IEEE0_MII_CONTROL, reg_val);
4694
4695 /* Enable/Disable Autodetection */
4696
4697 CL22_RD_OVER_CL45(bp, phy,
4698 MDIO_REG_BANK_SERDES_DIGITAL,
4699 MDIO_SERDES_DIGITAL_A_1000X_CONTROL1, &reg_val);
4700 reg_val &= ~(MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_SIGNAL_DETECT_EN |
4701 MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_INVERT_SIGNAL_DETECT);
4702 reg_val |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_FIBER_MODE;
4703 if (vars->line_speed == SPEED_AUTO_NEG)
4704 reg_val |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET;
4705 else
4706 reg_val &= ~MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET;
4707
4708 CL22_WR_OVER_CL45(bp, phy,
4709 MDIO_REG_BANK_SERDES_DIGITAL,
4710 MDIO_SERDES_DIGITAL_A_1000X_CONTROL1, reg_val);
4711
4712 /* Enable TetonII and BAM autoneg */
4713 CL22_RD_OVER_CL45(bp, phy,
4714 MDIO_REG_BANK_BAM_NEXT_PAGE,
4715 MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL,
4716 &reg_val);
4717 if (vars->line_speed == SPEED_AUTO_NEG) {
4718 /* Enable BAM aneg Mode and TetonII aneg Mode */
4719 reg_val |= (MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_BAM_MODE |
4720 MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_TETON_AN);
4721 } else {
4722 /* TetonII and BAM Autoneg Disabled */
4723 reg_val &= ~(MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_BAM_MODE |
4724 MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_TETON_AN);
4725 }
4726 CL22_WR_OVER_CL45(bp, phy,
4727 MDIO_REG_BANK_BAM_NEXT_PAGE,
4728 MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL,
4729 reg_val);
4730
4731 if (enable_cl73) {
4732 /* Enable Cl73 FSM status bits */
4733 CL22_WR_OVER_CL45(bp, phy,
4734 MDIO_REG_BANK_CL73_USERB0,
4735 MDIO_CL73_USERB0_CL73_UCTRL,
4736 0xe);
4737
4738 /* Enable BAM Station Manager*/
4739 CL22_WR_OVER_CL45(bp, phy,
4740 MDIO_REG_BANK_CL73_USERB0,
4741 MDIO_CL73_USERB0_CL73_BAM_CTRL1,
4742 MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_EN |
4743 MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_STATION_MNGR_EN |
4744 MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_NP_AFTER_BP_EN);
4745
4746 /* Advertise CL73 link speeds */
4747 CL22_RD_OVER_CL45(bp, phy,
4748 MDIO_REG_BANK_CL73_IEEEB1,
4749 MDIO_CL73_IEEEB1_AN_ADV2,
4750 &reg_val);
4751 if (phy->speed_cap_mask &
4752 PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)
4753 reg_val |= MDIO_CL73_IEEEB1_AN_ADV2_ADVR_10G_KX4;
4754 if (phy->speed_cap_mask &
4755 PORT_HW_CFG_SPEED_CAPABILITY_D0_1G)
4756 reg_val |= MDIO_CL73_IEEEB1_AN_ADV2_ADVR_1000M_KX;
4757
4758 CL22_WR_OVER_CL45(bp, phy,
4759 MDIO_REG_BANK_CL73_IEEEB1,
4760 MDIO_CL73_IEEEB1_AN_ADV2,
4761 reg_val);
4762
4763 /* CL73 Autoneg Enabled */
4764 reg_val = MDIO_CL73_IEEEB0_CL73_AN_CONTROL_AN_EN;
4765
4766 } else /* CL73 Autoneg Disabled */
4767 reg_val = 0;
4768
4769 CL22_WR_OVER_CL45(bp, phy,
4770 MDIO_REG_BANK_CL73_IEEEB0,
4771 MDIO_CL73_IEEEB0_CL73_AN_CONTROL, reg_val);
4772 }
4773
4774 /* program SerDes, forced speed */
4775 static void bnx2x_program_serdes(struct bnx2x_phy *phy,
4776 struct link_params *params,
4777 struct link_vars *vars)
4778 {
4779 struct bnx2x *bp = params->bp;
4780 u16 reg_val;
4781
4782 /* program duplex, disable autoneg and sgmii*/
4783 CL22_RD_OVER_CL45(bp, phy,
4784 MDIO_REG_BANK_COMBO_IEEE0,
4785 MDIO_COMBO_IEEE0_MII_CONTROL, &reg_val);
4786 reg_val &= ~(MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX |
4787 MDIO_COMBO_IEEO_MII_CONTROL_AN_EN |
4788 MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_MASK);
4789 if (phy->req_duplex == DUPLEX_FULL)
4790 reg_val |= MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX;
4791 CL22_WR_OVER_CL45(bp, phy,
4792 MDIO_REG_BANK_COMBO_IEEE0,
4793 MDIO_COMBO_IEEE0_MII_CONTROL, reg_val);
4794
4795 /*
4796 * program speed
4797 * - needed only if the speed is greater than 1G (2.5G or 10G)
4798 */
4799 CL22_RD_OVER_CL45(bp, phy,
4800 MDIO_REG_BANK_SERDES_DIGITAL,
4801 MDIO_SERDES_DIGITAL_MISC1, &reg_val);
4802 /* clearing the speed value before setting the right speed */
4803 DP(NETIF_MSG_LINK, "MDIO_REG_BANK_SERDES_DIGITAL = 0x%x\n", reg_val);
4804
4805 reg_val &= ~(MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_MASK |
4806 MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_SEL);
4807
4808 if (!((vars->line_speed == SPEED_1000) ||
4809 (vars->line_speed == SPEED_100) ||
4810 (vars->line_speed == SPEED_10))) {
4811
4812 reg_val |= (MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_156_25M |
4813 MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_SEL);
4814 if (vars->line_speed == SPEED_10000)
4815 reg_val |=
4816 MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_10G_CX4;
4817 }
4818
4819 CL22_WR_OVER_CL45(bp, phy,
4820 MDIO_REG_BANK_SERDES_DIGITAL,
4821 MDIO_SERDES_DIGITAL_MISC1, reg_val);
4822
4823 }
4824
4825 static void bnx2x_set_brcm_cl37_advertisement(struct bnx2x_phy *phy,
4826 struct link_params *params)
4827 {
4828 struct bnx2x *bp = params->bp;
4829 u16 val = 0;
4830
4831 /* configure the 48 bits for BAM AN */
4832
4833 /* set extended capabilities */
4834 if (phy->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_2_5G)
4835 val |= MDIO_OVER_1G_UP1_2_5G;
4836 if (phy->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)
4837 val |= MDIO_OVER_1G_UP1_10G;
4838 CL22_WR_OVER_CL45(bp, phy,
4839 MDIO_REG_BANK_OVER_1G,
4840 MDIO_OVER_1G_UP1, val);
4841
4842 CL22_WR_OVER_CL45(bp, phy,
4843 MDIO_REG_BANK_OVER_1G,
4844 MDIO_OVER_1G_UP3, 0x400);
4845 }
4846
4847 static void bnx2x_set_ieee_aneg_advertisement(struct bnx2x_phy *phy,
4848 struct link_params *params,
4849 u16 ieee_fc)
4850 {
4851 struct bnx2x *bp = params->bp;
4852 u16 val;
4853 /* for AN, we are always publishing full duplex */
4854
4855 CL22_WR_OVER_CL45(bp, phy,
4856 MDIO_REG_BANK_COMBO_IEEE0,
4857 MDIO_COMBO_IEEE0_AUTO_NEG_ADV, ieee_fc);
4858 CL22_RD_OVER_CL45(bp, phy,
4859 MDIO_REG_BANK_CL73_IEEEB1,
4860 MDIO_CL73_IEEEB1_AN_ADV1, &val);
4861 val &= ~MDIO_CL73_IEEEB1_AN_ADV1_PAUSE_BOTH;
4862 val |= ((ieee_fc<<3) & MDIO_CL73_IEEEB1_AN_ADV1_PAUSE_MASK);
4863 CL22_WR_OVER_CL45(bp, phy,
4864 MDIO_REG_BANK_CL73_IEEEB1,
4865 MDIO_CL73_IEEEB1_AN_ADV1, val);
4866 }
4867
4868 static void bnx2x_restart_autoneg(struct bnx2x_phy *phy,
4869 struct link_params *params,
4870 u8 enable_cl73)
4871 {
4872 struct bnx2x *bp = params->bp;
4873 u16 mii_control;
4874
4875 DP(NETIF_MSG_LINK, "bnx2x_restart_autoneg\n");
4876 /* Enable and restart BAM/CL37 aneg */
4877
4878 if (enable_cl73) {
4879 CL22_RD_OVER_CL45(bp, phy,
4880 MDIO_REG_BANK_CL73_IEEEB0,
4881 MDIO_CL73_IEEEB0_CL73_AN_CONTROL,
4882 &mii_control);
4883
4884 CL22_WR_OVER_CL45(bp, phy,
4885 MDIO_REG_BANK_CL73_IEEEB0,
4886 MDIO_CL73_IEEEB0_CL73_AN_CONTROL,
4887 (mii_control |
4888 MDIO_CL73_IEEEB0_CL73_AN_CONTROL_AN_EN |
4889 MDIO_CL73_IEEEB0_CL73_AN_CONTROL_RESTART_AN));
4890 } else {
4891
4892 CL22_RD_OVER_CL45(bp, phy,
4893 MDIO_REG_BANK_COMBO_IEEE0,
4894 MDIO_COMBO_IEEE0_MII_CONTROL,
4895 &mii_control);
4896 DP(NETIF_MSG_LINK,
4897 "bnx2x_restart_autoneg mii_control before = 0x%x\n",
4898 mii_control);
4899 CL22_WR_OVER_CL45(bp, phy,
4900 MDIO_REG_BANK_COMBO_IEEE0,
4901 MDIO_COMBO_IEEE0_MII_CONTROL,
4902 (mii_control |
4903 MDIO_COMBO_IEEO_MII_CONTROL_AN_EN |
4904 MDIO_COMBO_IEEO_MII_CONTROL_RESTART_AN));
4905 }
4906 }
4907
4908 static void bnx2x_initialize_sgmii_process(struct bnx2x_phy *phy,
4909 struct link_params *params,
4910 struct link_vars *vars)
4911 {
4912 struct bnx2x *bp = params->bp;
4913 u16 control1;
4914
4915 /* in SGMII mode, the unicore is always slave */
4916
4917 CL22_RD_OVER_CL45(bp, phy,
4918 MDIO_REG_BANK_SERDES_DIGITAL,
4919 MDIO_SERDES_DIGITAL_A_1000X_CONTROL1,
4920 &control1);
4921 control1 |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_INVERT_SIGNAL_DETECT;
4922 /* set sgmii mode (and not fiber) */
4923 control1 &= ~(MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_FIBER_MODE |
4924 MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET |
4925 MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_MSTR_MODE);
4926 CL22_WR_OVER_CL45(bp, phy,
4927 MDIO_REG_BANK_SERDES_DIGITAL,
4928 MDIO_SERDES_DIGITAL_A_1000X_CONTROL1,
4929 control1);
4930
4931 /* if forced speed */
4932 if (!(vars->line_speed == SPEED_AUTO_NEG)) {
4933 /* set speed, disable autoneg */
4934 u16 mii_control;
4935
4936 CL22_RD_OVER_CL45(bp, phy,
4937 MDIO_REG_BANK_COMBO_IEEE0,
4938 MDIO_COMBO_IEEE0_MII_CONTROL,
4939 &mii_control);
4940 mii_control &= ~(MDIO_COMBO_IEEO_MII_CONTROL_AN_EN |
4941 MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_MASK|
4942 MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX);
4943
4944 switch (vars->line_speed) {
4945 case SPEED_100:
4946 mii_control |=
4947 MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_100;
4948 break;
4949 case SPEED_1000:
4950 mii_control |=
4951 MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_1000;
4952 break;
4953 case SPEED_10:
4954 /* there is nothing to set for 10M */
4955 break;
4956 default:
4957 /* invalid speed for SGMII */
4958 DP(NETIF_MSG_LINK, "Invalid line_speed 0x%x\n",
4959 vars->line_speed);
4960 break;
4961 }
4962
4963 /* setting the full duplex */
4964 if (phy->req_duplex == DUPLEX_FULL)
4965 mii_control |=
4966 MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX;
4967 CL22_WR_OVER_CL45(bp, phy,
4968 MDIO_REG_BANK_COMBO_IEEE0,
4969 MDIO_COMBO_IEEE0_MII_CONTROL,
4970 mii_control);
4971
4972 } else { /* AN mode */
4973 /* enable and restart AN */
4974 bnx2x_restart_autoneg(phy, params, 0);
4975 }
4976 }
4977
4978
4979 /*
4980 * link management
4981 */
4982
4983 static int bnx2x_direct_parallel_detect_used(struct bnx2x_phy *phy,
4984 struct link_params *params)
4985 {
4986 struct bnx2x *bp = params->bp;
4987 u16 pd_10g, status2_1000x;
4988 if (phy->req_line_speed != SPEED_AUTO_NEG)
4989 return 0;
4990 CL22_RD_OVER_CL45(bp, phy,
4991 MDIO_REG_BANK_SERDES_DIGITAL,
4992 MDIO_SERDES_DIGITAL_A_1000X_STATUS2,
4993 &status2_1000x);
4994 CL22_RD_OVER_CL45(bp, phy,
4995 MDIO_REG_BANK_SERDES_DIGITAL,
4996 MDIO_SERDES_DIGITAL_A_1000X_STATUS2,
4997 &status2_1000x);
4998 if (status2_1000x & MDIO_SERDES_DIGITAL_A_1000X_STATUS2_AN_DISABLED) {
4999 DP(NETIF_MSG_LINK, "1G parallel detect link on port %d\n",
5000 params->port);
5001 return 1;
5002 }
5003
5004 CL22_RD_OVER_CL45(bp, phy,
5005 MDIO_REG_BANK_10G_PARALLEL_DETECT,
5006 MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_STATUS,
5007 &pd_10g);
5008
5009 if (pd_10g & MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_STATUS_PD_LINK) {
5010 DP(NETIF_MSG_LINK, "10G parallel detect link on port %d\n",
5011 params->port);
5012 return 1;
5013 }
5014 return 0;
5015 }
5016
5017 static void bnx2x_flow_ctrl_resolve(struct bnx2x_phy *phy,
5018 struct link_params *params,
5019 struct link_vars *vars,
5020 u32 gp_status)
5021 {
5022 struct bnx2x *bp = params->bp;
5023 u16 ld_pause; /* local driver */
5024 u16 lp_pause; /* link partner */
5025 u16 pause_result;
5026
5027 vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;
5028
5029 /* resolve from gp_status in case of AN complete and not sgmii */
5030 if (phy->req_flow_ctrl != BNX2X_FLOW_CTRL_AUTO)
5031 vars->flow_ctrl = phy->req_flow_ctrl;
5032 else if (phy->req_line_speed != SPEED_AUTO_NEG)
5033 vars->flow_ctrl = params->req_fc_auto_adv;
5034 else if ((gp_status & MDIO_AN_CL73_OR_37_COMPLETE) &&
5035 (!(vars->phy_flags & PHY_SGMII_FLAG))) {
5036 if (bnx2x_direct_parallel_detect_used(phy, params)) {
5037 vars->flow_ctrl = params->req_fc_auto_adv;
5038 return;
5039 }
5040 if ((gp_status &
5041 (MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_AUTONEG_COMPLETE |
5042 MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_MR_LP_NP_AN_ABLE)) ==
5043 (MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_AUTONEG_COMPLETE |
5044 MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_MR_LP_NP_AN_ABLE)) {
5045
5046 CL22_RD_OVER_CL45(bp, phy,
5047 MDIO_REG_BANK_CL73_IEEEB1,
5048 MDIO_CL73_IEEEB1_AN_ADV1,
5049 &ld_pause);
5050 CL22_RD_OVER_CL45(bp, phy,
5051 MDIO_REG_BANK_CL73_IEEEB1,
5052 MDIO_CL73_IEEEB1_AN_LP_ADV1,
5053 &lp_pause);
5054 pause_result = (ld_pause &
5055 MDIO_CL73_IEEEB1_AN_ADV1_PAUSE_MASK)
5056 >> 8;
5057 pause_result |= (lp_pause &
5058 MDIO_CL73_IEEEB1_AN_LP_ADV1_PAUSE_MASK)
5059 >> 10;
5060 DP(NETIF_MSG_LINK, "pause_result CL73 0x%x\n",
5061 pause_result);
5062 } else {
5063 CL22_RD_OVER_CL45(bp, phy,
5064 MDIO_REG_BANK_COMBO_IEEE0,
5065 MDIO_COMBO_IEEE0_AUTO_NEG_ADV,
5066 &ld_pause);
5067 CL22_RD_OVER_CL45(bp, phy,
5068 MDIO_REG_BANK_COMBO_IEEE0,
5069 MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1,
5070 &lp_pause);
5071 pause_result = (ld_pause &
5072 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_MASK)>>5;
5073 pause_result |= (lp_pause &
5074 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_MASK)>>7;
5075 DP(NETIF_MSG_LINK, "pause_result CL37 0x%x\n",
5076 pause_result);
5077 }
5078 bnx2x_pause_resolve(vars, pause_result);
5079 }
5080 DP(NETIF_MSG_LINK, "flow_ctrl 0x%x\n", vars->flow_ctrl);
5081 }
5082
5083 static void bnx2x_check_fallback_to_cl37(struct bnx2x_phy *phy,
5084 struct link_params *params)
5085 {
5086 struct bnx2x *bp = params->bp;
5087 u16 rx_status, ustat_val, cl37_fsm_received;
5088 DP(NETIF_MSG_LINK, "bnx2x_check_fallback_to_cl37\n");
5089 /* Step 1: Make sure signal is detected */
5090 CL22_RD_OVER_CL45(bp, phy,
5091 MDIO_REG_BANK_RX0,
5092 MDIO_RX0_RX_STATUS,
5093 &rx_status);
5094 if ((rx_status & MDIO_RX0_RX_STATUS_SIGDET) !=
5095 (MDIO_RX0_RX_STATUS_SIGDET)) {
5096 DP(NETIF_MSG_LINK, "Signal is not detected. Restoring CL73."
5097 "rx_status(0x80b0) = 0x%x\n", rx_status);
5098 CL22_WR_OVER_CL45(bp, phy,
5099 MDIO_REG_BANK_CL73_IEEEB0,
5100 MDIO_CL73_IEEEB0_CL73_AN_CONTROL,
5101 MDIO_CL73_IEEEB0_CL73_AN_CONTROL_AN_EN);
5102 return;
5103 }
5104 /* Step 2: Check CL73 state machine */
5105 CL22_RD_OVER_CL45(bp, phy,
5106 MDIO_REG_BANK_CL73_USERB0,
5107 MDIO_CL73_USERB0_CL73_USTAT1,
5108 &ustat_val);
5109 if ((ustat_val &
5110 (MDIO_CL73_USERB0_CL73_USTAT1_LINK_STATUS_CHECK |
5111 MDIO_CL73_USERB0_CL73_USTAT1_AN_GOOD_CHECK_BAM37)) !=
5112 (MDIO_CL73_USERB0_CL73_USTAT1_LINK_STATUS_CHECK |
5113 MDIO_CL73_USERB0_CL73_USTAT1_AN_GOOD_CHECK_BAM37)) {
5114 DP(NETIF_MSG_LINK, "CL73 state-machine is not stable. "
5115 "ustat_val(0x8371) = 0x%x\n", ustat_val);
5116 return;
5117 }
5118 /*
5119 * Step 3: Check CL37 Message Pages received to indicate LP
5120 * supports only CL37
5121 */
5122 CL22_RD_OVER_CL45(bp, phy,
5123 MDIO_REG_BANK_REMOTE_PHY,
5124 MDIO_REMOTE_PHY_MISC_RX_STATUS,
5125 &cl37_fsm_received);
5126 if ((cl37_fsm_received &
5127 (MDIO_REMOTE_PHY_MISC_RX_STATUS_CL37_FSM_RECEIVED_OVER1G_MSG |
5128 MDIO_REMOTE_PHY_MISC_RX_STATUS_CL37_FSM_RECEIVED_BRCM_OUI_MSG)) !=
5129 (MDIO_REMOTE_PHY_MISC_RX_STATUS_CL37_FSM_RECEIVED_OVER1G_MSG |
5130 MDIO_REMOTE_PHY_MISC_RX_STATUS_CL37_FSM_RECEIVED_BRCM_OUI_MSG)) {
5131 DP(NETIF_MSG_LINK, "No CL37 FSM were received. "
5132 "misc_rx_status(0x8330) = 0x%x\n",
5133 cl37_fsm_received);
5134 return;
5135 }
5136 /*
5137 * The combined cl37/cl73 fsm state information indicating that
5138 * we are connected to a device which does not support cl73, but
5139 * does support cl37 BAM. In this case we disable cl73 and
5140 * restart cl37 auto-neg
5141 */
5142
5143 /* Disable CL73 */
5144 CL22_WR_OVER_CL45(bp, phy,
5145 MDIO_REG_BANK_CL73_IEEEB0,
5146 MDIO_CL73_IEEEB0_CL73_AN_CONTROL,
5147 0);
5148 /* Restart CL37 autoneg */
5149 bnx2x_restart_autoneg(phy, params, 0);
5150 DP(NETIF_MSG_LINK, "Disabling CL73, and restarting CL37 autoneg\n");
5151 }
5152
5153 static void bnx2x_xgxs_an_resolve(struct bnx2x_phy *phy,
5154 struct link_params *params,
5155 struct link_vars *vars,
5156 u32 gp_status)
5157 {
5158 if (gp_status & MDIO_AN_CL73_OR_37_COMPLETE)
5159 vars->link_status |=
5160 LINK_STATUS_AUTO_NEGOTIATE_COMPLETE;
5161
5162 if (bnx2x_direct_parallel_detect_used(phy, params))
5163 vars->link_status |=
5164 LINK_STATUS_PARALLEL_DETECTION_USED;
5165 }
5166 static int bnx2x_get_link_speed_duplex(struct bnx2x_phy *phy,
5167 struct link_params *params,
5168 struct link_vars *vars,
5169 u16 is_link_up,
5170 u16 speed_mask,
5171 u16 is_duplex)
5172 {
5173 struct bnx2x *bp = params->bp;
5174 if (phy->req_line_speed == SPEED_AUTO_NEG)
5175 vars->link_status |= LINK_STATUS_AUTO_NEGOTIATE_ENABLED;
5176 if (is_link_up) {
5177 DP(NETIF_MSG_LINK, "phy link up\n");
5178
5179 vars->phy_link_up = 1;
5180 vars->link_status |= LINK_STATUS_LINK_UP;
5181
5182 switch (speed_mask) {
5183 case GP_STATUS_10M:
5184 vars->line_speed = SPEED_10;
5185 if (vars->duplex == DUPLEX_FULL)
5186 vars->link_status |= LINK_10TFD;
5187 else
5188 vars->link_status |= LINK_10THD;
5189 break;
5190
5191 case GP_STATUS_100M:
5192 vars->line_speed = SPEED_100;
5193 if (vars->duplex == DUPLEX_FULL)
5194 vars->link_status |= LINK_100TXFD;
5195 else
5196 vars->link_status |= LINK_100TXHD;
5197 break;
5198
5199 case GP_STATUS_1G:
5200 case GP_STATUS_1G_KX:
5201 vars->line_speed = SPEED_1000;
5202 if (vars->duplex == DUPLEX_FULL)
5203 vars->link_status |= LINK_1000TFD;
5204 else
5205 vars->link_status |= LINK_1000THD;
5206 break;
5207
5208 case GP_STATUS_2_5G:
5209 vars->line_speed = SPEED_2500;
5210 if (vars->duplex == DUPLEX_FULL)
5211 vars->link_status |= LINK_2500TFD;
5212 else
5213 vars->link_status |= LINK_2500THD;
5214 break;
5215
5216 case GP_STATUS_5G:
5217 case GP_STATUS_6G:
5218 DP(NETIF_MSG_LINK,
5219 "link speed unsupported gp_status 0x%x\n",
5220 speed_mask);
5221 return -EINVAL;
5222
5223 case GP_STATUS_10G_KX4:
5224 case GP_STATUS_10G_HIG:
5225 case GP_STATUS_10G_CX4:
5226 case GP_STATUS_10G_KR:
5227 case GP_STATUS_10G_SFI:
5228 case GP_STATUS_10G_XFI:
5229 vars->line_speed = SPEED_10000;
5230 vars->link_status |= LINK_10GTFD;
5231 break;
5232 case GP_STATUS_20G_DXGXS:
5233 vars->line_speed = SPEED_20000;
5234 vars->link_status |= LINK_20GTFD;
5235 break;
5236 default:
5237 DP(NETIF_MSG_LINK,
5238 "link speed unsupported gp_status 0x%x\n",
5239 speed_mask);
5240 return -EINVAL;
5241 }
5242 } else { /* link_down */
5243 DP(NETIF_MSG_LINK, "phy link down\n");
5244
5245 vars->phy_link_up = 0;
5246
5247 vars->duplex = DUPLEX_FULL;
5248 vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;
5249 vars->mac_type = MAC_TYPE_NONE;
5250 }
5251 DP(NETIF_MSG_LINK, " phy_link_up %x line_speed %d\n",
5252 vars->phy_link_up, vars->line_speed);
5253 return 0;
5254 }
5255
5256 static int bnx2x_link_settings_status(struct bnx2x_phy *phy,
5257 struct link_params *params,
5258 struct link_vars *vars)
5259 {
5260
5261 struct bnx2x *bp = params->bp;
5262
5263 u16 gp_status, duplex = DUPLEX_HALF, link_up = 0, speed_mask;
5264 int rc = 0;
5265
5266 /* Read gp_status */
5267 CL22_RD_OVER_CL45(bp, phy,
5268 MDIO_REG_BANK_GP_STATUS,
5269 MDIO_GP_STATUS_TOP_AN_STATUS1,
5270 &gp_status);
5271 if (gp_status & MDIO_GP_STATUS_TOP_AN_STATUS1_DUPLEX_STATUS)
5272 duplex = DUPLEX_FULL;
5273 if (gp_status & MDIO_GP_STATUS_TOP_AN_STATUS1_LINK_STATUS)
5274 link_up = 1;
5275 speed_mask = gp_status & GP_STATUS_SPEED_MASK;
5276 DP(NETIF_MSG_LINK, "gp_status 0x%x, is_link_up %d, speed_mask 0x%x\n",
5277 gp_status, link_up, speed_mask);
5278 rc = bnx2x_get_link_speed_duplex(phy, params, vars, link_up, speed_mask,
5279 duplex);
5280 if (rc == -EINVAL)
5281 return rc;
5282
5283 if (gp_status & MDIO_GP_STATUS_TOP_AN_STATUS1_LINK_STATUS) {
5284 if (SINGLE_MEDIA_DIRECT(params)) {
5285 bnx2x_flow_ctrl_resolve(phy, params, vars, gp_status);
5286 if (phy->req_line_speed == SPEED_AUTO_NEG)
5287 bnx2x_xgxs_an_resolve(phy, params, vars,
5288 gp_status);
5289 }
5290 } else { /* link_down */
5291 if ((phy->req_line_speed == SPEED_AUTO_NEG) &&
5292 SINGLE_MEDIA_DIRECT(params)) {
5293 /* Check signal is detected */
5294 bnx2x_check_fallback_to_cl37(phy, params);
5295 }
5296 }
5297
5298 DP(NETIF_MSG_LINK, "duplex %x flow_ctrl 0x%x link_status 0x%x\n",
5299 vars->duplex, vars->flow_ctrl, vars->link_status);
5300 return rc;
5301 }
5302
5303 static int bnx2x_warpcore_read_status(struct bnx2x_phy *phy,
5304 struct link_params *params,
5305 struct link_vars *vars)
5306 {
5307
5308 struct bnx2x *bp = params->bp;
5309
5310 u8 lane;
5311 u16 gp_status1, gp_speed, link_up, duplex = DUPLEX_FULL;
5312 int rc = 0;
5313 lane = bnx2x_get_warpcore_lane(phy, params);
5314 /* Read gp_status */
5315 if (phy->req_line_speed > SPEED_10000) {
5316 u16 temp_link_up;
5317 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
5318 1, &temp_link_up);
5319 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
5320 1, &link_up);
5321 DP(NETIF_MSG_LINK, "PCS RX link status = 0x%x-->0x%x\n",
5322 temp_link_up, link_up);
5323 link_up &= (1<<2);
5324 if (link_up)
5325 bnx2x_ext_phy_resolve_fc(phy, params, vars);
5326 } else {
5327 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
5328 MDIO_WC_REG_GP2_STATUS_GP_2_1, &gp_status1);
5329 DP(NETIF_MSG_LINK, "0x81d1 = 0x%x\n", gp_status1);
5330 /* Check for either KR or generic link up. */
5331 gp_status1 = ((gp_status1 >> 8) & 0xf) |
5332 ((gp_status1 >> 12) & 0xf);
5333 link_up = gp_status1 & (1 << lane);
5334 if (link_up && SINGLE_MEDIA_DIRECT(params)) {
5335 u16 pd, gp_status4;
5336 if (phy->req_line_speed == SPEED_AUTO_NEG) {
5337 /* Check Autoneg complete */
5338 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
5339 MDIO_WC_REG_GP2_STATUS_GP_2_4,
5340 &gp_status4);
5341 if (gp_status4 & ((1<<12)<<lane))
5342 vars->link_status |=
5343 LINK_STATUS_AUTO_NEGOTIATE_COMPLETE;
5344
5345 /* Check parallel detect used */
5346 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
5347 MDIO_WC_REG_PAR_DET_10G_STATUS,
5348 &pd);
5349 if (pd & (1<<15))
5350 vars->link_status |=
5351 LINK_STATUS_PARALLEL_DETECTION_USED;
5352 }
5353 bnx2x_ext_phy_resolve_fc(phy, params, vars);
5354 }
5355 }
5356
5357 if (lane < 2) {
5358 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
5359 MDIO_WC_REG_GP2_STATUS_GP_2_2, &gp_speed);
5360 } else {
5361 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
5362 MDIO_WC_REG_GP2_STATUS_GP_2_3, &gp_speed);
5363 }
5364 DP(NETIF_MSG_LINK, "lane %d gp_speed 0x%x\n", lane, gp_speed);
5365
5366 if ((lane & 1) == 0)
5367 gp_speed <<= 8;
5368 gp_speed &= 0x3f00;
5369
5370
5371 rc = bnx2x_get_link_speed_duplex(phy, params, vars, link_up, gp_speed,
5372 duplex);
5373
5374 DP(NETIF_MSG_LINK, "duplex %x flow_ctrl 0x%x link_status 0x%x\n",
5375 vars->duplex, vars->flow_ctrl, vars->link_status);
5376 return rc;
5377 }
5378 static void bnx2x_set_gmii_tx_driver(struct link_params *params)
5379 {
5380 struct bnx2x *bp = params->bp;
5381 struct bnx2x_phy *phy = &params->phy[INT_PHY];
5382 u16 lp_up2;
5383 u16 tx_driver;
5384 u16 bank;
5385
5386 /* read precomp */
5387 CL22_RD_OVER_CL45(bp, phy,
5388 MDIO_REG_BANK_OVER_1G,
5389 MDIO_OVER_1G_LP_UP2, &lp_up2);
5390
5391 /* bits [10:7] at lp_up2, positioned at [15:12] */
5392 lp_up2 = (((lp_up2 & MDIO_OVER_1G_LP_UP2_PREEMPHASIS_MASK) >>
5393 MDIO_OVER_1G_LP_UP2_PREEMPHASIS_SHIFT) <<
5394 MDIO_TX0_TX_DRIVER_PREEMPHASIS_SHIFT);
5395
5396 if (lp_up2 == 0)
5397 return;
5398
5399 for (bank = MDIO_REG_BANK_TX0; bank <= MDIO_REG_BANK_TX3;
5400 bank += (MDIO_REG_BANK_TX1 - MDIO_REG_BANK_TX0)) {
5401 CL22_RD_OVER_CL45(bp, phy,
5402 bank,
5403 MDIO_TX0_TX_DRIVER, &tx_driver);
5404
5405 /* replace tx_driver bits [15:12] */
5406 if (lp_up2 !=
5407 (tx_driver & MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK)) {
5408 tx_driver &= ~MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK;
5409 tx_driver |= lp_up2;
5410 CL22_WR_OVER_CL45(bp, phy,
5411 bank,
5412 MDIO_TX0_TX_DRIVER, tx_driver);
5413 }
5414 }
5415 }
5416
5417 static int bnx2x_emac_program(struct link_params *params,
5418 struct link_vars *vars)
5419 {
5420 struct bnx2x *bp = params->bp;
5421 u8 port = params->port;
5422 u16 mode = 0;
5423
5424 DP(NETIF_MSG_LINK, "setting link speed & duplex\n");
5425 bnx2x_bits_dis(bp, GRCBASE_EMAC0 + port*0x400 +
5426 EMAC_REG_EMAC_MODE,
5427 (EMAC_MODE_25G_MODE |
5428 EMAC_MODE_PORT_MII_10M |
5429 EMAC_MODE_HALF_DUPLEX));
5430 switch (vars->line_speed) {
5431 case SPEED_10:
5432 mode |= EMAC_MODE_PORT_MII_10M;
5433 break;
5434
5435 case SPEED_100:
5436 mode |= EMAC_MODE_PORT_MII;
5437 break;
5438
5439 case SPEED_1000:
5440 mode |= EMAC_MODE_PORT_GMII;
5441 break;
5442
5443 case SPEED_2500:
5444 mode |= (EMAC_MODE_25G_MODE | EMAC_MODE_PORT_GMII);
5445 break;
5446
5447 default:
5448 /* 10G not valid for EMAC */
5449 DP(NETIF_MSG_LINK, "Invalid line_speed 0x%x\n",
5450 vars->line_speed);
5451 return -EINVAL;
5452 }
5453
5454 if (vars->duplex == DUPLEX_HALF)
5455 mode |= EMAC_MODE_HALF_DUPLEX;
5456 bnx2x_bits_en(bp,
5457 GRCBASE_EMAC0 + port*0x400 + EMAC_REG_EMAC_MODE,
5458 mode);
5459
5460 bnx2x_set_led(params, vars, LED_MODE_OPER, vars->line_speed);
5461 return 0;
5462 }
5463
5464 static void bnx2x_set_preemphasis(struct bnx2x_phy *phy,
5465 struct link_params *params)
5466 {
5467
5468 u16 bank, i = 0;
5469 struct bnx2x *bp = params->bp;
5470
5471 for (bank = MDIO_REG_BANK_RX0, i = 0; bank <= MDIO_REG_BANK_RX3;
5472 bank += (MDIO_REG_BANK_RX1-MDIO_REG_BANK_RX0), i++) {
5473 CL22_WR_OVER_CL45(bp, phy,
5474 bank,
5475 MDIO_RX0_RX_EQ_BOOST,
5476 phy->rx_preemphasis[i]);
5477 }
5478
5479 for (bank = MDIO_REG_BANK_TX0, i = 0; bank <= MDIO_REG_BANK_TX3;
5480 bank += (MDIO_REG_BANK_TX1 - MDIO_REG_BANK_TX0), i++) {
5481 CL22_WR_OVER_CL45(bp, phy,
5482 bank,
5483 MDIO_TX0_TX_DRIVER,
5484 phy->tx_preemphasis[i]);
5485 }
5486 }
5487
5488 static void bnx2x_xgxs_config_init(struct bnx2x_phy *phy,
5489 struct link_params *params,
5490 struct link_vars *vars)
5491 {
5492 struct bnx2x *bp = params->bp;
5493 u8 enable_cl73 = (SINGLE_MEDIA_DIRECT(params) ||
5494 (params->loopback_mode == LOOPBACK_XGXS));
5495 if (!(vars->phy_flags & PHY_SGMII_FLAG)) {
5496 if (SINGLE_MEDIA_DIRECT(params) &&
5497 (params->feature_config_flags &
5498 FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED))
5499 bnx2x_set_preemphasis(phy, params);
5500
5501 /* forced speed requested? */
5502 if (vars->line_speed != SPEED_AUTO_NEG ||
5503 (SINGLE_MEDIA_DIRECT(params) &&
5504 params->loopback_mode == LOOPBACK_EXT)) {
5505 DP(NETIF_MSG_LINK, "not SGMII, no AN\n");
5506
5507 /* disable autoneg */
5508 bnx2x_set_autoneg(phy, params, vars, 0);
5509
5510 /* program speed and duplex */
5511 bnx2x_program_serdes(phy, params, vars);
5512
5513 } else { /* AN_mode */
5514 DP(NETIF_MSG_LINK, "not SGMII, AN\n");
5515
5516 /* AN enabled */
5517 bnx2x_set_brcm_cl37_advertisement(phy, params);
5518
5519 /* program duplex & pause advertisement (for aneg) */
5520 bnx2x_set_ieee_aneg_advertisement(phy, params,
5521 vars->ieee_fc);
5522
5523 /* enable autoneg */
5524 bnx2x_set_autoneg(phy, params, vars, enable_cl73);
5525
5526 /* enable and restart AN */
5527 bnx2x_restart_autoneg(phy, params, enable_cl73);
5528 }
5529
5530 } else { /* SGMII mode */
5531 DP(NETIF_MSG_LINK, "SGMII\n");
5532
5533 bnx2x_initialize_sgmii_process(phy, params, vars);
5534 }
5535 }
5536
5537 static int bnx2x_prepare_xgxs(struct bnx2x_phy *phy,
5538 struct link_params *params,
5539 struct link_vars *vars)
5540 {
5541 int rc;
5542 vars->phy_flags |= PHY_XGXS_FLAG;
5543 if ((phy->req_line_speed &&
5544 ((phy->req_line_speed == SPEED_100) ||
5545 (phy->req_line_speed == SPEED_10))) ||
5546 (!phy->req_line_speed &&
5547 (phy->speed_cap_mask >=
5548 PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_FULL) &&
5549 (phy->speed_cap_mask <
5550 PORT_HW_CFG_SPEED_CAPABILITY_D0_1G)) ||
5551 (phy->type == PORT_HW_CFG_SERDES_EXT_PHY_TYPE_DIRECT_SD))
5552 vars->phy_flags |= PHY_SGMII_FLAG;
5553 else
5554 vars->phy_flags &= ~PHY_SGMII_FLAG;
5555
5556 bnx2x_calc_ieee_aneg_adv(phy, params, &vars->ieee_fc);
5557 bnx2x_set_aer_mmd(params, phy);
5558 if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT)
5559 bnx2x_set_master_ln(params, phy);
5560
5561 rc = bnx2x_reset_unicore(params, phy, 0);
5562 /* reset the SerDes and wait for reset bit return low */
5563 if (rc != 0)
5564 return rc;
5565
5566 bnx2x_set_aer_mmd(params, phy);
5567 /* setting the masterLn_def again after the reset */
5568 if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) {
5569 bnx2x_set_master_ln(params, phy);
5570 bnx2x_set_swap_lanes(params, phy);
5571 }
5572
5573 return rc;
5574 }
5575
5576 static u16 bnx2x_wait_reset_complete(struct bnx2x *bp,
5577 struct bnx2x_phy *phy,
5578 struct link_params *params)
5579 {
5580 u16 cnt, ctrl;
5581 /* Wait for soft reset to get cleared up to 1 sec */
5582 for (cnt = 0; cnt < 1000; cnt++) {
5583 if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM54618SE)
5584 bnx2x_cl22_read(bp, phy,
5585 MDIO_PMA_REG_CTRL, &ctrl);
5586 else
5587 bnx2x_cl45_read(bp, phy,
5588 MDIO_PMA_DEVAD,
5589 MDIO_PMA_REG_CTRL, &ctrl);
5590 if (!(ctrl & (1<<15)))
5591 break;
5592 msleep(1);
5593 }
5594
5595 if (cnt == 1000)
5596 netdev_err(bp->dev, "Warning: PHY was not initialized,"
5597 " Port %d\n",
5598 params->port);
5599 DP(NETIF_MSG_LINK, "control reg 0x%x (after %d ms)\n", ctrl, cnt);
5600 return cnt;
5601 }
5602
5603 static void bnx2x_link_int_enable(struct link_params *params)
5604 {
5605 u8 port = params->port;
5606 u32 mask;
5607 struct bnx2x *bp = params->bp;
5608
5609 /* Setting the status to report on link up for either XGXS or SerDes */
5610 if (CHIP_IS_E3(bp)) {
5611 mask = NIG_MASK_XGXS0_LINK_STATUS;
5612 if (!(SINGLE_MEDIA_DIRECT(params)))
5613 mask |= NIG_MASK_MI_INT;
5614 } else if (params->switch_cfg == SWITCH_CFG_10G) {
5615 mask = (NIG_MASK_XGXS0_LINK10G |
5616 NIG_MASK_XGXS0_LINK_STATUS);
5617 DP(NETIF_MSG_LINK, "enabled XGXS interrupt\n");
5618 if (!(SINGLE_MEDIA_DIRECT(params)) &&
5619 params->phy[INT_PHY].type !=
5620 PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE) {
5621 mask |= NIG_MASK_MI_INT;
5622 DP(NETIF_MSG_LINK, "enabled external phy int\n");
5623 }
5624
5625 } else { /* SerDes */
5626 mask = NIG_MASK_SERDES0_LINK_STATUS;
5627 DP(NETIF_MSG_LINK, "enabled SerDes interrupt\n");
5628 if (!(SINGLE_MEDIA_DIRECT(params)) &&
5629 params->phy[INT_PHY].type !=
5630 PORT_HW_CFG_SERDES_EXT_PHY_TYPE_NOT_CONN) {
5631 mask |= NIG_MASK_MI_INT;
5632 DP(NETIF_MSG_LINK, "enabled external phy int\n");
5633 }
5634 }
5635 bnx2x_bits_en(bp,
5636 NIG_REG_MASK_INTERRUPT_PORT0 + port*4,
5637 mask);
5638
5639 DP(NETIF_MSG_LINK, "port %x, is_xgxs %x, int_status 0x%x\n", port,
5640 (params->switch_cfg == SWITCH_CFG_10G),
5641 REG_RD(bp, NIG_REG_STATUS_INTERRUPT_PORT0 + port*4));
5642 DP(NETIF_MSG_LINK, " int_mask 0x%x, MI_INT %x, SERDES_LINK %x\n",
5643 REG_RD(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port*4),
5644 REG_RD(bp, NIG_REG_EMAC0_STATUS_MISC_MI_INT + port*0x18),
5645 REG_RD(bp, NIG_REG_SERDES0_STATUS_LINK_STATUS+port*0x3c));
5646 DP(NETIF_MSG_LINK, " 10G %x, XGXS_LINK %x\n",
5647 REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK10G + port*0x68),
5648 REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK_STATUS + port*0x68));
5649 }
5650
5651 static void bnx2x_rearm_latch_signal(struct bnx2x *bp, u8 port,
5652 u8 exp_mi_int)
5653 {
5654 u32 latch_status = 0;
5655
5656 /*
5657 * Disable the MI INT ( external phy int ) by writing 1 to the
5658 * status register. Link down indication is high-active-signal,
5659 * so in this case we need to write the status to clear the XOR
5660 */
5661 /* Read Latched signals */
5662 latch_status = REG_RD(bp,
5663 NIG_REG_LATCH_STATUS_0 + port*8);
5664 DP(NETIF_MSG_LINK, "latch_status = 0x%x\n", latch_status);
5665 /* Handle only those with latched-signal=up.*/
5666 if (exp_mi_int)
5667 bnx2x_bits_en(bp,
5668 NIG_REG_STATUS_INTERRUPT_PORT0
5669 + port*4,
5670 NIG_STATUS_EMAC0_MI_INT);
5671 else
5672 bnx2x_bits_dis(bp,
5673 NIG_REG_STATUS_INTERRUPT_PORT0
5674 + port*4,
5675 NIG_STATUS_EMAC0_MI_INT);
5676
5677 if (latch_status & 1) {
5678
5679 /* For all latched-signal=up : Re-Arm Latch signals */
5680 REG_WR(bp, NIG_REG_LATCH_STATUS_0 + port*8,
5681 (latch_status & 0xfffe) | (latch_status & 1));
5682 }
5683 /* For all latched-signal=up,Write original_signal to status */
5684 }
5685
5686 static void bnx2x_link_int_ack(struct link_params *params,
5687 struct link_vars *vars, u8 is_10g_plus)
5688 {
5689 struct bnx2x *bp = params->bp;
5690 u8 port = params->port;
5691 u32 mask;
5692 /*
5693 * First reset all status we assume only one line will be
5694 * change at a time
5695 */
5696 bnx2x_bits_dis(bp, NIG_REG_STATUS_INTERRUPT_PORT0 + port*4,
5697 (NIG_STATUS_XGXS0_LINK10G |
5698 NIG_STATUS_XGXS0_LINK_STATUS |
5699 NIG_STATUS_SERDES0_LINK_STATUS));
5700 if (vars->phy_link_up) {
5701 if (USES_WARPCORE(bp))
5702 mask = NIG_STATUS_XGXS0_LINK_STATUS;
5703 else {
5704 if (is_10g_plus)
5705 mask = NIG_STATUS_XGXS0_LINK10G;
5706 else if (params->switch_cfg == SWITCH_CFG_10G) {
5707 /*
5708 * Disable the link interrupt by writing 1 to
5709 * the relevant lane in the status register
5710 */
5711 u32 ser_lane =
5712 ((params->lane_config &
5713 PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >>
5714 PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT);
5715 mask = ((1 << ser_lane) <<
5716 NIG_STATUS_XGXS0_LINK_STATUS_SIZE);
5717 } else
5718 mask = NIG_STATUS_SERDES0_LINK_STATUS;
5719 }
5720 DP(NETIF_MSG_LINK, "Ack link up interrupt with mask 0x%x\n",
5721 mask);
5722 bnx2x_bits_en(bp,
5723 NIG_REG_STATUS_INTERRUPT_PORT0 + port*4,
5724 mask);
5725 }
5726 }
5727
5728 static int bnx2x_format_ver(u32 num, u8 *str, u16 *len)
5729 {
5730 u8 *str_ptr = str;
5731 u32 mask = 0xf0000000;
5732 u8 shift = 8*4;
5733 u8 digit;
5734 u8 remove_leading_zeros = 1;
5735 if (*len < 10) {
5736 /* Need more than 10chars for this format */
5737 *str_ptr = '\0';
5738 (*len)--;
5739 return -EINVAL;
5740 }
5741 while (shift > 0) {
5742
5743 shift -= 4;
5744 digit = ((num & mask) >> shift);
5745 if (digit == 0 && remove_leading_zeros) {
5746 mask = mask >> 4;
5747 continue;
5748 } else if (digit < 0xa)
5749 *str_ptr = digit + '0';
5750 else
5751 *str_ptr = digit - 0xa + 'a';
5752 remove_leading_zeros = 0;
5753 str_ptr++;
5754 (*len)--;
5755 mask = mask >> 4;
5756 if (shift == 4*4) {
5757 *str_ptr = '.';
5758 str_ptr++;
5759 (*len)--;
5760 remove_leading_zeros = 1;
5761 }
5762 }
5763 return 0;
5764 }
5765
5766
5767 static int bnx2x_null_format_ver(u32 spirom_ver, u8 *str, u16 *len)
5768 {
5769 str[0] = '\0';
5770 (*len)--;
5771 return 0;
5772 }
5773
5774 int bnx2x_get_ext_phy_fw_version(struct link_params *params, u8 driver_loaded,
5775 u8 *version, u16 len)
5776 {
5777 struct bnx2x *bp;
5778 u32 spirom_ver = 0;
5779 int status = 0;
5780 u8 *ver_p = version;
5781 u16 remain_len = len;
5782 if (version == NULL || params == NULL)
5783 return -EINVAL;
5784 bp = params->bp;
5785
5786 /* Extract first external phy*/
5787 version[0] = '\0';
5788 spirom_ver = REG_RD(bp, params->phy[EXT_PHY1].ver_addr);
5789
5790 if (params->phy[EXT_PHY1].format_fw_ver) {
5791 status |= params->phy[EXT_PHY1].format_fw_ver(spirom_ver,
5792 ver_p,
5793 &remain_len);
5794 ver_p += (len - remain_len);
5795 }
5796 if ((params->num_phys == MAX_PHYS) &&
5797 (params->phy[EXT_PHY2].ver_addr != 0)) {
5798 spirom_ver = REG_RD(bp, params->phy[EXT_PHY2].ver_addr);
5799 if (params->phy[EXT_PHY2].format_fw_ver) {
5800 *ver_p = '/';
5801 ver_p++;
5802 remain_len--;
5803 status |= params->phy[EXT_PHY2].format_fw_ver(
5804 spirom_ver,
5805 ver_p,
5806 &remain_len);
5807 ver_p = version + (len - remain_len);
5808 }
5809 }
5810 *ver_p = '\0';
5811 return status;
5812 }
5813
5814 static void bnx2x_set_xgxs_loopback(struct bnx2x_phy *phy,
5815 struct link_params *params)
5816 {
5817 u8 port = params->port;
5818 struct bnx2x *bp = params->bp;
5819
5820 if (phy->req_line_speed != SPEED_1000) {
5821 u32 md_devad = 0;
5822
5823 DP(NETIF_MSG_LINK, "XGXS 10G loopback enable\n");
5824
5825 if (!CHIP_IS_E3(bp)) {
5826 /* change the uni_phy_addr in the nig */
5827 md_devad = REG_RD(bp, (NIG_REG_XGXS0_CTRL_MD_DEVAD +
5828 port*0x18));
5829
5830 REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_DEVAD + port*0x18,
5831 0x5);
5832 }
5833
5834 bnx2x_cl45_write(bp, phy,
5835 5,
5836 (MDIO_REG_BANK_AER_BLOCK +
5837 (MDIO_AER_BLOCK_AER_REG & 0xf)),
5838 0x2800);
5839
5840 bnx2x_cl45_write(bp, phy,
5841 5,
5842 (MDIO_REG_BANK_CL73_IEEEB0 +
5843 (MDIO_CL73_IEEEB0_CL73_AN_CONTROL & 0xf)),
5844 0x6041);
5845 msleep(200);
5846 /* set aer mmd back */
5847 bnx2x_set_aer_mmd(params, phy);
5848
5849 if (!CHIP_IS_E3(bp)) {
5850 /* and md_devad */
5851 REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_DEVAD + port*0x18,
5852 md_devad);
5853 }
5854 } else {
5855 u16 mii_ctrl;
5856 DP(NETIF_MSG_LINK, "XGXS 1G loopback enable\n");
5857 bnx2x_cl45_read(bp, phy, 5,
5858 (MDIO_REG_BANK_COMBO_IEEE0 +
5859 (MDIO_COMBO_IEEE0_MII_CONTROL & 0xf)),
5860 &mii_ctrl);
5861 bnx2x_cl45_write(bp, phy, 5,
5862 (MDIO_REG_BANK_COMBO_IEEE0 +
5863 (MDIO_COMBO_IEEE0_MII_CONTROL & 0xf)),
5864 mii_ctrl |
5865 MDIO_COMBO_IEEO_MII_CONTROL_LOOPBACK);
5866 }
5867 }
5868
5869 int bnx2x_set_led(struct link_params *params,
5870 struct link_vars *vars, u8 mode, u32 speed)
5871 {
5872 u8 port = params->port;
5873 u16 hw_led_mode = params->hw_led_mode;
5874 int rc = 0;
5875 u8 phy_idx;
5876 u32 tmp;
5877 u32 emac_base = port ? GRCBASE_EMAC1 : GRCBASE_EMAC0;
5878 struct bnx2x *bp = params->bp;
5879 DP(NETIF_MSG_LINK, "bnx2x_set_led: port %x, mode %d\n", port, mode);
5880 DP(NETIF_MSG_LINK, "speed 0x%x, hw_led_mode 0x%x\n",
5881 speed, hw_led_mode);
5882 /* In case */
5883 for (phy_idx = EXT_PHY1; phy_idx < MAX_PHYS; phy_idx++) {
5884 if (params->phy[phy_idx].set_link_led) {
5885 params->phy[phy_idx].set_link_led(
5886 &params->phy[phy_idx], params, mode);
5887 }
5888 }
5889
5890 switch (mode) {
5891 case LED_MODE_FRONT_PANEL_OFF:
5892 case LED_MODE_OFF:
5893 REG_WR(bp, NIG_REG_LED_10G_P0 + port*4, 0);
5894 REG_WR(bp, NIG_REG_LED_MODE_P0 + port*4,
5895 SHARED_HW_CFG_LED_MAC1);
5896
5897 tmp = EMAC_RD(bp, EMAC_REG_EMAC_LED);
5898 EMAC_WR(bp, EMAC_REG_EMAC_LED, (tmp | EMAC_LED_OVERRIDE));
5899 break;
5900
5901 case LED_MODE_OPER:
5902 /*
5903 * For all other phys, OPER mode is same as ON, so in case
5904 * link is down, do nothing
5905 */
5906 if (!vars->link_up)
5907 break;
5908 case LED_MODE_ON:
5909 if (((params->phy[EXT_PHY1].type ==
5910 PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727) ||
5911 (params->phy[EXT_PHY1].type ==
5912 PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8722)) &&
5913 CHIP_IS_E2(bp) && params->num_phys == 2) {
5914 /*
5915 * This is a work-around for E2+8727 Configurations
5916 */
5917 if (mode == LED_MODE_ON ||
5918 speed == SPEED_10000){
5919 REG_WR(bp, NIG_REG_LED_MODE_P0 + port*4, 0);
5920 REG_WR(bp, NIG_REG_LED_10G_P0 + port*4, 1);
5921
5922 tmp = EMAC_RD(bp, EMAC_REG_EMAC_LED);
5923 EMAC_WR(bp, EMAC_REG_EMAC_LED,
5924 (tmp | EMAC_LED_OVERRIDE));
5925 /*
5926 * return here without enabling traffic
5927 * LED blink andsetting rate in ON mode.
5928 * In oper mode, enabling LED blink
5929 * and setting rate is needed.
5930 */
5931 if (mode == LED_MODE_ON)
5932 return rc;
5933 }
5934 } else if (SINGLE_MEDIA_DIRECT(params)) {
5935 /*
5936 * This is a work-around for HW issue found when link
5937 * is up in CL73
5938 */
5939 REG_WR(bp, NIG_REG_LED_10G_P0 + port*4, 1);
5940 if (CHIP_IS_E1x(bp) ||
5941 CHIP_IS_E2(bp) ||
5942 (mode == LED_MODE_ON))
5943 REG_WR(bp, NIG_REG_LED_MODE_P0 + port*4, 0);
5944 else
5945 REG_WR(bp, NIG_REG_LED_MODE_P0 + port*4,
5946 hw_led_mode);
5947 } else
5948 REG_WR(bp, NIG_REG_LED_MODE_P0 + port*4, hw_led_mode);
5949
5950 REG_WR(bp, NIG_REG_LED_CONTROL_OVERRIDE_TRAFFIC_P0 + port*4, 0);
5951 /* Set blinking rate to ~15.9Hz */
5952 REG_WR(bp, NIG_REG_LED_CONTROL_BLINK_RATE_P0 + port*4,
5953 LED_BLINK_RATE_VAL);
5954 REG_WR(bp, NIG_REG_LED_CONTROL_BLINK_RATE_ENA_P0 +
5955 port*4, 1);
5956 tmp = EMAC_RD(bp, EMAC_REG_EMAC_LED);
5957 EMAC_WR(bp, EMAC_REG_EMAC_LED, (tmp & (~EMAC_LED_OVERRIDE)));
5958
5959 if (CHIP_IS_E1(bp) &&
5960 ((speed == SPEED_2500) ||
5961 (speed == SPEED_1000) ||
5962 (speed == SPEED_100) ||
5963 (speed == SPEED_10))) {
5964 /*
5965 * On Everest 1 Ax chip versions for speeds less than
5966 * 10G LED scheme is different
5967 */
5968 REG_WR(bp, NIG_REG_LED_CONTROL_OVERRIDE_TRAFFIC_P0
5969 + port*4, 1);
5970 REG_WR(bp, NIG_REG_LED_CONTROL_TRAFFIC_P0 +
5971 port*4, 0);
5972 REG_WR(bp, NIG_REG_LED_CONTROL_BLINK_TRAFFIC_P0 +
5973 port*4, 1);
5974 }
5975 break;
5976
5977 default:
5978 rc = -EINVAL;
5979 DP(NETIF_MSG_LINK, "bnx2x_set_led: Invalid led mode %d\n",
5980 mode);
5981 break;
5982 }
5983 return rc;
5984
5985 }
5986
5987 /*
5988 * This function comes to reflect the actual link state read DIRECTLY from the
5989 * HW
5990 */
5991 int bnx2x_test_link(struct link_params *params, struct link_vars *vars,
5992 u8 is_serdes)
5993 {
5994 struct bnx2x *bp = params->bp;
5995 u16 gp_status = 0, phy_index = 0;
5996 u8 ext_phy_link_up = 0, serdes_phy_type;
5997 struct link_vars temp_vars;
5998 struct bnx2x_phy *int_phy = &params->phy[INT_PHY];
5999
6000 if (CHIP_IS_E3(bp)) {
6001 u16 link_up;
6002 if (params->req_line_speed[LINK_CONFIG_IDX(INT_PHY)]
6003 > SPEED_10000) {
6004 /* Check 20G link */
6005 bnx2x_cl45_read(bp, int_phy, MDIO_WC_DEVAD,
6006 1, &link_up);
6007 bnx2x_cl45_read(bp, int_phy, MDIO_WC_DEVAD,
6008 1, &link_up);
6009 link_up &= (1<<2);
6010 } else {
6011 /* Check 10G link and below*/
6012 u8 lane = bnx2x_get_warpcore_lane(int_phy, params);
6013 bnx2x_cl45_read(bp, int_phy, MDIO_WC_DEVAD,
6014 MDIO_WC_REG_GP2_STATUS_GP_2_1,
6015 &gp_status);
6016 gp_status = ((gp_status >> 8) & 0xf) |
6017 ((gp_status >> 12) & 0xf);
6018 link_up = gp_status & (1 << lane);
6019 }
6020 if (!link_up)
6021 return -ESRCH;
6022 } else {
6023 CL22_RD_OVER_CL45(bp, int_phy,
6024 MDIO_REG_BANK_GP_STATUS,
6025 MDIO_GP_STATUS_TOP_AN_STATUS1,
6026 &gp_status);
6027 /* link is up only if both local phy and external phy are up */
6028 if (!(gp_status & MDIO_GP_STATUS_TOP_AN_STATUS1_LINK_STATUS))
6029 return -ESRCH;
6030 }
6031 /* In XGXS loopback mode, do not check external PHY */
6032 if (params->loopback_mode == LOOPBACK_XGXS)
6033 return 0;
6034
6035 switch (params->num_phys) {
6036 case 1:
6037 /* No external PHY */
6038 return 0;
6039 case 2:
6040 ext_phy_link_up = params->phy[EXT_PHY1].read_status(
6041 &params->phy[EXT_PHY1],
6042 params, &temp_vars);
6043 break;
6044 case 3: /* Dual Media */
6045 for (phy_index = EXT_PHY1; phy_index < params->num_phys;
6046 phy_index++) {
6047 serdes_phy_type = ((params->phy[phy_index].media_type ==
6048 ETH_PHY_SFP_FIBER) ||
6049 (params->phy[phy_index].media_type ==
6050 ETH_PHY_XFP_FIBER) ||
6051 (params->phy[phy_index].media_type ==
6052 ETH_PHY_DA_TWINAX));
6053
6054 if (is_serdes != serdes_phy_type)
6055 continue;
6056 if (params->phy[phy_index].read_status) {
6057 ext_phy_link_up |=
6058 params->phy[phy_index].read_status(
6059 &params->phy[phy_index],
6060 params, &temp_vars);
6061 }
6062 }
6063 break;
6064 }
6065 if (ext_phy_link_up)
6066 return 0;
6067 return -ESRCH;
6068 }
6069
6070 static int bnx2x_link_initialize(struct link_params *params,
6071 struct link_vars *vars)
6072 {
6073 int rc = 0;
6074 u8 phy_index, non_ext_phy;
6075 struct bnx2x *bp = params->bp;
6076 /*
6077 * In case of external phy existence, the line speed would be the
6078 * line speed linked up by the external phy. In case it is direct
6079 * only, then the line_speed during initialization will be
6080 * equal to the req_line_speed
6081 */
6082 vars->line_speed = params->phy[INT_PHY].req_line_speed;
6083
6084 /*
6085 * Initialize the internal phy in case this is a direct board
6086 * (no external phys), or this board has external phy which requires
6087 * to first.
6088 */
6089 if (!USES_WARPCORE(bp))
6090 bnx2x_prepare_xgxs(&params->phy[INT_PHY], params, vars);
6091 /* init ext phy and enable link state int */
6092 non_ext_phy = (SINGLE_MEDIA_DIRECT(params) ||
6093 (params->loopback_mode == LOOPBACK_XGXS));
6094
6095 if (non_ext_phy ||
6096 (params->phy[EXT_PHY1].flags & FLAGS_INIT_XGXS_FIRST) ||
6097 (params->loopback_mode == LOOPBACK_EXT_PHY)) {
6098 struct bnx2x_phy *phy = &params->phy[INT_PHY];
6099 if (vars->line_speed == SPEED_AUTO_NEG &&
6100 (CHIP_IS_E1x(bp) ||
6101 CHIP_IS_E2(bp)))
6102 bnx2x_set_parallel_detection(phy, params);
6103 if (params->phy[INT_PHY].config_init)
6104 params->phy[INT_PHY].config_init(phy,
6105 params,
6106 vars);
6107 }
6108
6109 /* Init external phy*/
6110 if (non_ext_phy) {
6111 if (params->phy[INT_PHY].supported &
6112 SUPPORTED_FIBRE)
6113 vars->link_status |= LINK_STATUS_SERDES_LINK;
6114 } else {
6115 for (phy_index = EXT_PHY1; phy_index < params->num_phys;
6116 phy_index++) {
6117 /*
6118 * No need to initialize second phy in case of first
6119 * phy only selection. In case of second phy, we do
6120 * need to initialize the first phy, since they are
6121 * connected.
6122 */
6123 if (params->phy[phy_index].supported &
6124 SUPPORTED_FIBRE)
6125 vars->link_status |= LINK_STATUS_SERDES_LINK;
6126
6127 if (phy_index == EXT_PHY2 &&
6128 (bnx2x_phy_selection(params) ==
6129 PORT_HW_CFG_PHY_SELECTION_FIRST_PHY)) {
6130 DP(NETIF_MSG_LINK, "Not initializing"
6131 " second phy\n");
6132 continue;
6133 }
6134 params->phy[phy_index].config_init(
6135 &params->phy[phy_index],
6136 params, vars);
6137 }
6138 }
6139 /* Reset the interrupt indication after phy was initialized */
6140 bnx2x_bits_dis(bp, NIG_REG_STATUS_INTERRUPT_PORT0 +
6141 params->port*4,
6142 (NIG_STATUS_XGXS0_LINK10G |
6143 NIG_STATUS_XGXS0_LINK_STATUS |
6144 NIG_STATUS_SERDES0_LINK_STATUS |
6145 NIG_MASK_MI_INT));
6146 bnx2x_update_mng(params, vars->link_status);
6147 return rc;
6148 }
6149
6150 static void bnx2x_int_link_reset(struct bnx2x_phy *phy,
6151 struct link_params *params)
6152 {
6153 /* reset the SerDes/XGXS */
6154 REG_WR(params->bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_CLEAR,
6155 (0x1ff << (params->port*16)));
6156 }
6157
6158 static void bnx2x_common_ext_link_reset(struct bnx2x_phy *phy,
6159 struct link_params *params)
6160 {
6161 struct bnx2x *bp = params->bp;
6162 u8 gpio_port;
6163 /* HW reset */
6164 if (CHIP_IS_E2(bp))
6165 gpio_port = BP_PATH(bp);
6166 else
6167 gpio_port = params->port;
6168 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
6169 MISC_REGISTERS_GPIO_OUTPUT_LOW,
6170 gpio_port);
6171 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
6172 MISC_REGISTERS_GPIO_OUTPUT_LOW,
6173 gpio_port);
6174 DP(NETIF_MSG_LINK, "reset external PHY\n");
6175 }
6176
6177 static int bnx2x_update_link_down(struct link_params *params,
6178 struct link_vars *vars)
6179 {
6180 struct bnx2x *bp = params->bp;
6181 u8 port = params->port;
6182
6183 DP(NETIF_MSG_LINK, "Port %x: Link is down\n", port);
6184 bnx2x_set_led(params, vars, LED_MODE_OFF, 0);
6185 vars->phy_flags &= ~PHY_PHYSICAL_LINK_FLAG;
6186 /* indicate no mac active */
6187 vars->mac_type = MAC_TYPE_NONE;
6188
6189 /* update shared memory */
6190 vars->link_status &= ~(LINK_STATUS_SPEED_AND_DUPLEX_MASK |
6191 LINK_STATUS_LINK_UP |
6192 LINK_STATUS_PHYSICAL_LINK_FLAG |
6193 LINK_STATUS_AUTO_NEGOTIATE_COMPLETE |
6194 LINK_STATUS_RX_FLOW_CONTROL_FLAG_MASK |
6195 LINK_STATUS_TX_FLOW_CONTROL_FLAG_MASK |
6196 LINK_STATUS_PARALLEL_DETECTION_FLAG_MASK);
6197 vars->line_speed = 0;
6198 bnx2x_update_mng(params, vars->link_status);
6199
6200 /* activate nig drain */
6201 REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + port*4, 1);
6202
6203 /* disable emac */
6204 if (!CHIP_IS_E3(bp))
6205 REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 0);
6206
6207 msleep(10);
6208 /* reset BigMac/Xmac */
6209 if (CHIP_IS_E1x(bp) ||
6210 CHIP_IS_E2(bp)) {
6211 bnx2x_bmac_rx_disable(bp, params->port);
6212 REG_WR(bp, GRCBASE_MISC +
6213 MISC_REGISTERS_RESET_REG_2_CLEAR,
6214 (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
6215 }
6216 if (CHIP_IS_E3(bp))
6217 bnx2x_xmac_disable(params);
6218
6219 return 0;
6220 }
6221
6222 static int bnx2x_update_link_up(struct link_params *params,
6223 struct link_vars *vars,
6224 u8 link_10g)
6225 {
6226 struct bnx2x *bp = params->bp;
6227 u8 port = params->port;
6228 int rc = 0;
6229
6230 vars->link_status |= (LINK_STATUS_LINK_UP |
6231 LINK_STATUS_PHYSICAL_LINK_FLAG);
6232 vars->phy_flags |= PHY_PHYSICAL_LINK_FLAG;
6233
6234 if (vars->flow_ctrl & BNX2X_FLOW_CTRL_TX)
6235 vars->link_status |=
6236 LINK_STATUS_TX_FLOW_CONTROL_ENABLED;
6237
6238 if (vars->flow_ctrl & BNX2X_FLOW_CTRL_RX)
6239 vars->link_status |=
6240 LINK_STATUS_RX_FLOW_CONTROL_ENABLED;
6241 if (USES_WARPCORE(bp)) {
6242 if (link_10g) {
6243 if (bnx2x_xmac_enable(params, vars, 0) ==
6244 -ESRCH) {
6245 DP(NETIF_MSG_LINK, "Found errors on XMAC\n");
6246 vars->link_up = 0;
6247 vars->phy_flags |= PHY_HALF_OPEN_CONN_FLAG;
6248 vars->link_status &= ~LINK_STATUS_LINK_UP;
6249 }
6250 } else
6251 bnx2x_umac_enable(params, vars, 0);
6252 bnx2x_set_led(params, vars,
6253 LED_MODE_OPER, vars->line_speed);
6254 }
6255 if ((CHIP_IS_E1x(bp) ||
6256 CHIP_IS_E2(bp))) {
6257 if (link_10g) {
6258 if (bnx2x_bmac_enable(params, vars, 0) ==
6259 -ESRCH) {
6260 DP(NETIF_MSG_LINK, "Found errors on BMAC\n");
6261 vars->link_up = 0;
6262 vars->phy_flags |= PHY_HALF_OPEN_CONN_FLAG;
6263 vars->link_status &= ~LINK_STATUS_LINK_UP;
6264 }
6265
6266 bnx2x_set_led(params, vars,
6267 LED_MODE_OPER, SPEED_10000);
6268 } else {
6269 rc = bnx2x_emac_program(params, vars);
6270 bnx2x_emac_enable(params, vars, 0);
6271
6272 /* AN complete? */
6273 if ((vars->link_status &
6274 LINK_STATUS_AUTO_NEGOTIATE_COMPLETE)
6275 && (!(vars->phy_flags & PHY_SGMII_FLAG)) &&
6276 SINGLE_MEDIA_DIRECT(params))
6277 bnx2x_set_gmii_tx_driver(params);
6278 }
6279 }
6280
6281 /* PBF - link up */
6282 if (CHIP_IS_E1x(bp))
6283 rc |= bnx2x_pbf_update(params, vars->flow_ctrl,
6284 vars->line_speed);
6285
6286 /* disable drain */
6287 REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + port*4, 0);
6288
6289 /* update shared memory */
6290 bnx2x_update_mng(params, vars->link_status);
6291 msleep(20);
6292 return rc;
6293 }
6294 /*
6295 * The bnx2x_link_update function should be called upon link
6296 * interrupt.
6297 * Link is considered up as follows:
6298 * - DIRECT_SINGLE_MEDIA - Only XGXS link (internal link) needs
6299 * to be up
6300 * - SINGLE_MEDIA - The link between the 577xx and the external
6301 * phy (XGXS) need to up as well as the external link of the
6302 * phy (PHY_EXT1)
6303 * - DUAL_MEDIA - The link between the 577xx and the first
6304 * external phy needs to be up, and at least one of the 2
6305 * external phy link must be up.
6306 */
6307 int bnx2x_link_update(struct link_params *params, struct link_vars *vars)
6308 {
6309 struct bnx2x *bp = params->bp;
6310 struct link_vars phy_vars[MAX_PHYS];
6311 u8 port = params->port;
6312 u8 link_10g_plus, phy_index;
6313 u8 ext_phy_link_up = 0, cur_link_up;
6314 int rc = 0;
6315 u8 is_mi_int = 0;
6316 u16 ext_phy_line_speed = 0, prev_line_speed = vars->line_speed;
6317 u8 active_external_phy = INT_PHY;
6318 vars->phy_flags &= ~PHY_HALF_OPEN_CONN_FLAG;
6319 for (phy_index = INT_PHY; phy_index < params->num_phys;
6320 phy_index++) {
6321 phy_vars[phy_index].flow_ctrl = 0;
6322 phy_vars[phy_index].link_status = 0;
6323 phy_vars[phy_index].line_speed = 0;
6324 phy_vars[phy_index].duplex = DUPLEX_FULL;
6325 phy_vars[phy_index].phy_link_up = 0;
6326 phy_vars[phy_index].link_up = 0;
6327 phy_vars[phy_index].fault_detected = 0;
6328 }
6329
6330 if (USES_WARPCORE(bp))
6331 bnx2x_set_aer_mmd(params, &params->phy[INT_PHY]);
6332
6333 DP(NETIF_MSG_LINK, "port %x, XGXS?%x, int_status 0x%x\n",
6334 port, (vars->phy_flags & PHY_XGXS_FLAG),
6335 REG_RD(bp, NIG_REG_STATUS_INTERRUPT_PORT0 + port*4));
6336
6337 is_mi_int = (u8)(REG_RD(bp, NIG_REG_EMAC0_STATUS_MISC_MI_INT +
6338 port*0x18) > 0);
6339 DP(NETIF_MSG_LINK, "int_mask 0x%x MI_INT %x, SERDES_LINK %x\n",
6340 REG_RD(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port*4),
6341 is_mi_int,
6342 REG_RD(bp, NIG_REG_SERDES0_STATUS_LINK_STATUS + port*0x3c));
6343
6344 DP(NETIF_MSG_LINK, " 10G %x, XGXS_LINK %x\n",
6345 REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK10G + port*0x68),
6346 REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK_STATUS + port*0x68));
6347
6348 /* disable emac */
6349 if (!CHIP_IS_E3(bp))
6350 REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 0);
6351
6352 /*
6353 * Step 1:
6354 * Check external link change only for external phys, and apply
6355 * priority selection between them in case the link on both phys
6356 * is up. Note that instead of the common vars, a temporary
6357 * vars argument is used since each phy may have different link/
6358 * speed/duplex result
6359 */
6360 for (phy_index = EXT_PHY1; phy_index < params->num_phys;
6361 phy_index++) {
6362 struct bnx2x_phy *phy = &params->phy[phy_index];
6363 if (!phy->read_status)
6364 continue;
6365 /* Read link status and params of this ext phy */
6366 cur_link_up = phy->read_status(phy, params,
6367 &phy_vars[phy_index]);
6368 if (cur_link_up) {
6369 DP(NETIF_MSG_LINK, "phy in index %d link is up\n",
6370 phy_index);
6371 } else {
6372 DP(NETIF_MSG_LINK, "phy in index %d link is down\n",
6373 phy_index);
6374 continue;
6375 }
6376
6377 if (!ext_phy_link_up) {
6378 ext_phy_link_up = 1;
6379 active_external_phy = phy_index;
6380 } else {
6381 switch (bnx2x_phy_selection(params)) {
6382 case PORT_HW_CFG_PHY_SELECTION_HARDWARE_DEFAULT:
6383 case PORT_HW_CFG_PHY_SELECTION_FIRST_PHY_PRIORITY:
6384 /*
6385 * In this option, the first PHY makes sure to pass the
6386 * traffic through itself only.
6387 * Its not clear how to reset the link on the second phy
6388 */
6389 active_external_phy = EXT_PHY1;
6390 break;
6391 case PORT_HW_CFG_PHY_SELECTION_SECOND_PHY_PRIORITY:
6392 /*
6393 * In this option, the first PHY makes sure to pass the
6394 * traffic through the second PHY.
6395 */
6396 active_external_phy = EXT_PHY2;
6397 break;
6398 default:
6399 /*
6400 * Link indication on both PHYs with the following cases
6401 * is invalid:
6402 * - FIRST_PHY means that second phy wasn't initialized,
6403 * hence its link is expected to be down
6404 * - SECOND_PHY means that first phy should not be able
6405 * to link up by itself (using configuration)
6406 * - DEFAULT should be overriden during initialiazation
6407 */
6408 DP(NETIF_MSG_LINK, "Invalid link indication"
6409 "mpc=0x%x. DISABLING LINK !!!\n",
6410 params->multi_phy_config);
6411 ext_phy_link_up = 0;
6412 break;
6413 }
6414 }
6415 }
6416 prev_line_speed = vars->line_speed;
6417 /*
6418 * Step 2:
6419 * Read the status of the internal phy. In case of
6420 * DIRECT_SINGLE_MEDIA board, this link is the external link,
6421 * otherwise this is the link between the 577xx and the first
6422 * external phy
6423 */
6424 if (params->phy[INT_PHY].read_status)
6425 params->phy[INT_PHY].read_status(
6426 &params->phy[INT_PHY],
6427 params, vars);
6428 /*
6429 * The INT_PHY flow control reside in the vars. This include the
6430 * case where the speed or flow control are not set to AUTO.
6431 * Otherwise, the active external phy flow control result is set
6432 * to the vars. The ext_phy_line_speed is needed to check if the
6433 * speed is different between the internal phy and external phy.
6434 * This case may be result of intermediate link speed change.
6435 */
6436 if (active_external_phy > INT_PHY) {
6437 vars->flow_ctrl = phy_vars[active_external_phy].flow_ctrl;
6438 /*
6439 * Link speed is taken from the XGXS. AN and FC result from
6440 * the external phy.
6441 */
6442 vars->link_status |= phy_vars[active_external_phy].link_status;
6443
6444 /*
6445 * if active_external_phy is first PHY and link is up - disable
6446 * disable TX on second external PHY
6447 */
6448 if (active_external_phy == EXT_PHY1) {
6449 if (params->phy[EXT_PHY2].phy_specific_func) {
6450 DP(NETIF_MSG_LINK, "Disabling TX on"
6451 " EXT_PHY2\n");
6452 params->phy[EXT_PHY2].phy_specific_func(
6453 &params->phy[EXT_PHY2],
6454 params, DISABLE_TX);
6455 }
6456 }
6457
6458 ext_phy_line_speed = phy_vars[active_external_phy].line_speed;
6459 vars->duplex = phy_vars[active_external_phy].duplex;
6460 if (params->phy[active_external_phy].supported &
6461 SUPPORTED_FIBRE)
6462 vars->link_status |= LINK_STATUS_SERDES_LINK;
6463 else
6464 vars->link_status &= ~LINK_STATUS_SERDES_LINK;
6465 DP(NETIF_MSG_LINK, "Active external phy selected: %x\n",
6466 active_external_phy);
6467 }
6468
6469 for (phy_index = EXT_PHY1; phy_index < params->num_phys;
6470 phy_index++) {
6471 if (params->phy[phy_index].flags &
6472 FLAGS_REARM_LATCH_SIGNAL) {
6473 bnx2x_rearm_latch_signal(bp, port,
6474 phy_index ==
6475 active_external_phy);
6476 break;
6477 }
6478 }
6479 DP(NETIF_MSG_LINK, "vars->flow_ctrl = 0x%x, vars->link_status = 0x%x,"
6480 " ext_phy_line_speed = %d\n", vars->flow_ctrl,
6481 vars->link_status, ext_phy_line_speed);
6482 /*
6483 * Upon link speed change set the NIG into drain mode. Comes to
6484 * deals with possible FIFO glitch due to clk change when speed
6485 * is decreased without link down indicator
6486 */
6487
6488 if (vars->phy_link_up) {
6489 if (!(SINGLE_MEDIA_DIRECT(params)) && ext_phy_link_up &&
6490 (ext_phy_line_speed != vars->line_speed)) {
6491 DP(NETIF_MSG_LINK, "Internal link speed %d is"
6492 " different than the external"
6493 " link speed %d\n", vars->line_speed,
6494 ext_phy_line_speed);
6495 vars->phy_link_up = 0;
6496 } else if (prev_line_speed != vars->line_speed) {
6497 REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4,
6498 0);
6499 msleep(1);
6500 }
6501 }
6502
6503 /* anything 10 and over uses the bmac */
6504 link_10g_plus = (vars->line_speed >= SPEED_10000);
6505
6506 bnx2x_link_int_ack(params, vars, link_10g_plus);
6507
6508 /*
6509 * In case external phy link is up, and internal link is down
6510 * (not initialized yet probably after link initialization, it
6511 * needs to be initialized.
6512 * Note that after link down-up as result of cable plug, the xgxs
6513 * link would probably become up again without the need
6514 * initialize it
6515 */
6516 if (!(SINGLE_MEDIA_DIRECT(params))) {
6517 DP(NETIF_MSG_LINK, "ext_phy_link_up = %d, int_link_up = %d,"
6518 " init_preceding = %d\n", ext_phy_link_up,
6519 vars->phy_link_up,
6520 params->phy[EXT_PHY1].flags &
6521 FLAGS_INIT_XGXS_FIRST);
6522 if (!(params->phy[EXT_PHY1].flags &
6523 FLAGS_INIT_XGXS_FIRST)
6524 && ext_phy_link_up && !vars->phy_link_up) {
6525 vars->line_speed = ext_phy_line_speed;
6526 if (vars->line_speed < SPEED_1000)
6527 vars->phy_flags |= PHY_SGMII_FLAG;
6528 else
6529 vars->phy_flags &= ~PHY_SGMII_FLAG;
6530
6531 if (params->phy[INT_PHY].config_init)
6532 params->phy[INT_PHY].config_init(
6533 &params->phy[INT_PHY], params,
6534 vars);
6535 }
6536 }
6537 /*
6538 * Link is up only if both local phy and external phy (in case of
6539 * non-direct board) are up and no fault detected on active PHY.
6540 */
6541 vars->link_up = (vars->phy_link_up &&
6542 (ext_phy_link_up ||
6543 SINGLE_MEDIA_DIRECT(params)) &&
6544 (phy_vars[active_external_phy].fault_detected == 0));
6545
6546 if (vars->link_up)
6547 rc = bnx2x_update_link_up(params, vars, link_10g_plus);
6548 else
6549 rc = bnx2x_update_link_down(params, vars);
6550
6551 return rc;
6552 }
6553
6554
6555 /*****************************************************************************/
6556 /* External Phy section */
6557 /*****************************************************************************/
6558 void bnx2x_ext_phy_hw_reset(struct bnx2x *bp, u8 port)
6559 {
6560 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
6561 MISC_REGISTERS_GPIO_OUTPUT_LOW, port);
6562 msleep(1);
6563 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
6564 MISC_REGISTERS_GPIO_OUTPUT_HIGH, port);
6565 }
6566
6567 static void bnx2x_save_spirom_version(struct bnx2x *bp, u8 port,
6568 u32 spirom_ver, u32 ver_addr)
6569 {
6570 DP(NETIF_MSG_LINK, "FW version 0x%x:0x%x for port %d\n",
6571 (u16)(spirom_ver>>16), (u16)spirom_ver, port);
6572
6573 if (ver_addr)
6574 REG_WR(bp, ver_addr, spirom_ver);
6575 }
6576
6577 static void bnx2x_save_bcm_spirom_ver(struct bnx2x *bp,
6578 struct bnx2x_phy *phy,
6579 u8 port)
6580 {
6581 u16 fw_ver1, fw_ver2;
6582
6583 bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD,
6584 MDIO_PMA_REG_ROM_VER1, &fw_ver1);
6585 bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD,
6586 MDIO_PMA_REG_ROM_VER2, &fw_ver2);
6587 bnx2x_save_spirom_version(bp, port, (u32)(fw_ver1<<16 | fw_ver2),
6588 phy->ver_addr);
6589 }
6590
6591 static void bnx2x_ext_phy_10G_an_resolve(struct bnx2x *bp,
6592 struct bnx2x_phy *phy,
6593 struct link_vars *vars)
6594 {
6595 u16 val;
6596 bnx2x_cl45_read(bp, phy,
6597 MDIO_AN_DEVAD,
6598 MDIO_AN_REG_STATUS, &val);
6599 bnx2x_cl45_read(bp, phy,
6600 MDIO_AN_DEVAD,
6601 MDIO_AN_REG_STATUS, &val);
6602 if (val & (1<<5))
6603 vars->link_status |= LINK_STATUS_AUTO_NEGOTIATE_COMPLETE;
6604 if ((val & (1<<0)) == 0)
6605 vars->link_status |= LINK_STATUS_PARALLEL_DETECTION_USED;
6606 }
6607
6608 /******************************************************************/
6609 /* common BCM8073/BCM8727 PHY SECTION */
6610 /******************************************************************/
6611 static void bnx2x_8073_resolve_fc(struct bnx2x_phy *phy,
6612 struct link_params *params,
6613 struct link_vars *vars)
6614 {
6615 struct bnx2x *bp = params->bp;
6616 if (phy->req_line_speed == SPEED_10 ||
6617 phy->req_line_speed == SPEED_100) {
6618 vars->flow_ctrl = phy->req_flow_ctrl;
6619 return;
6620 }
6621
6622 if (bnx2x_ext_phy_resolve_fc(phy, params, vars) &&
6623 (vars->flow_ctrl == BNX2X_FLOW_CTRL_NONE)) {
6624 u16 pause_result;
6625 u16 ld_pause; /* local */
6626 u16 lp_pause; /* link partner */
6627 bnx2x_cl45_read(bp, phy,
6628 MDIO_AN_DEVAD,
6629 MDIO_AN_REG_CL37_FC_LD, &ld_pause);
6630
6631 bnx2x_cl45_read(bp, phy,
6632 MDIO_AN_DEVAD,
6633 MDIO_AN_REG_CL37_FC_LP, &lp_pause);
6634 pause_result = (ld_pause &
6635 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) >> 5;
6636 pause_result |= (lp_pause &
6637 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) >> 7;
6638
6639 bnx2x_pause_resolve(vars, pause_result);
6640 DP(NETIF_MSG_LINK, "Ext PHY CL37 pause result 0x%x\n",
6641 pause_result);
6642 }
6643 }
6644 static int bnx2x_8073_8727_external_rom_boot(struct bnx2x *bp,
6645 struct bnx2x_phy *phy,
6646 u8 port)
6647 {
6648 u32 count = 0;
6649 u16 fw_ver1, fw_msgout;
6650 int rc = 0;
6651
6652 /* Boot port from external ROM */
6653 /* EDC grst */
6654 bnx2x_cl45_write(bp, phy,
6655 MDIO_PMA_DEVAD,
6656 MDIO_PMA_REG_GEN_CTRL,
6657 0x0001);
6658
6659 /* ucode reboot and rst */
6660 bnx2x_cl45_write(bp, phy,
6661 MDIO_PMA_DEVAD,
6662 MDIO_PMA_REG_GEN_CTRL,
6663 0x008c);
6664
6665 bnx2x_cl45_write(bp, phy,
6666 MDIO_PMA_DEVAD,
6667 MDIO_PMA_REG_MISC_CTRL1, 0x0001);
6668
6669 /* Reset internal microprocessor */
6670 bnx2x_cl45_write(bp, phy,
6671 MDIO_PMA_DEVAD,
6672 MDIO_PMA_REG_GEN_CTRL,
6673 MDIO_PMA_REG_GEN_CTRL_ROM_MICRO_RESET);
6674
6675 /* Release srst bit */
6676 bnx2x_cl45_write(bp, phy,
6677 MDIO_PMA_DEVAD,
6678 MDIO_PMA_REG_GEN_CTRL,
6679 MDIO_PMA_REG_GEN_CTRL_ROM_RESET_INTERNAL_MP);
6680
6681 /* Delay 100ms per the PHY specifications */
6682 msleep(100);
6683
6684 /* 8073 sometimes taking longer to download */
6685 do {
6686 count++;
6687 if (count > 300) {
6688 DP(NETIF_MSG_LINK,
6689 "bnx2x_8073_8727_external_rom_boot port %x:"
6690 "Download failed. fw version = 0x%x\n",
6691 port, fw_ver1);
6692 rc = -EINVAL;
6693 break;
6694 }
6695
6696 bnx2x_cl45_read(bp, phy,
6697 MDIO_PMA_DEVAD,
6698 MDIO_PMA_REG_ROM_VER1, &fw_ver1);
6699 bnx2x_cl45_read(bp, phy,
6700 MDIO_PMA_DEVAD,
6701 MDIO_PMA_REG_M8051_MSGOUT_REG, &fw_msgout);
6702
6703 msleep(1);
6704 } while (fw_ver1 == 0 || fw_ver1 == 0x4321 ||
6705 ((fw_msgout & 0xff) != 0x03 && (phy->type ==
6706 PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073)));
6707
6708 /* Clear ser_boot_ctl bit */
6709 bnx2x_cl45_write(bp, phy,
6710 MDIO_PMA_DEVAD,
6711 MDIO_PMA_REG_MISC_CTRL1, 0x0000);
6712 bnx2x_save_bcm_spirom_ver(bp, phy, port);
6713
6714 DP(NETIF_MSG_LINK,
6715 "bnx2x_8073_8727_external_rom_boot port %x:"
6716 "Download complete. fw version = 0x%x\n",
6717 port, fw_ver1);
6718
6719 return rc;
6720 }
6721
6722 /******************************************************************/
6723 /* BCM8073 PHY SECTION */
6724 /******************************************************************/
6725 static int bnx2x_8073_is_snr_needed(struct bnx2x *bp, struct bnx2x_phy *phy)
6726 {
6727 /* This is only required for 8073A1, version 102 only */
6728 u16 val;
6729
6730 /* Read 8073 HW revision*/
6731 bnx2x_cl45_read(bp, phy,
6732 MDIO_PMA_DEVAD,
6733 MDIO_PMA_REG_8073_CHIP_REV, &val);
6734
6735 if (val != 1) {
6736 /* No need to workaround in 8073 A1 */
6737 return 0;
6738 }
6739
6740 bnx2x_cl45_read(bp, phy,
6741 MDIO_PMA_DEVAD,
6742 MDIO_PMA_REG_ROM_VER2, &val);
6743
6744 /* SNR should be applied only for version 0x102 */
6745 if (val != 0x102)
6746 return 0;
6747
6748 return 1;
6749 }
6750
6751 static int bnx2x_8073_xaui_wa(struct bnx2x *bp, struct bnx2x_phy *phy)
6752 {
6753 u16 val, cnt, cnt1 ;
6754
6755 bnx2x_cl45_read(bp, phy,
6756 MDIO_PMA_DEVAD,
6757 MDIO_PMA_REG_8073_CHIP_REV, &val);
6758
6759 if (val > 0) {
6760 /* No need to workaround in 8073 A1 */
6761 return 0;
6762 }
6763 /* XAUI workaround in 8073 A0: */
6764
6765 /*
6766 * After loading the boot ROM and restarting Autoneg, poll
6767 * Dev1, Reg $C820:
6768 */
6769
6770 for (cnt = 0; cnt < 1000; cnt++) {
6771 bnx2x_cl45_read(bp, phy,
6772 MDIO_PMA_DEVAD,
6773 MDIO_PMA_REG_8073_SPEED_LINK_STATUS,
6774 &val);
6775 /*
6776 * If bit [14] = 0 or bit [13] = 0, continue on with
6777 * system initialization (XAUI work-around not required, as
6778 * these bits indicate 2.5G or 1G link up).
6779 */
6780 if (!(val & (1<<14)) || !(val & (1<<13))) {
6781 DP(NETIF_MSG_LINK, "XAUI work-around not required\n");
6782 return 0;
6783 } else if (!(val & (1<<15))) {
6784 DP(NETIF_MSG_LINK, "bit 15 went off\n");
6785 /*
6786 * If bit 15 is 0, then poll Dev1, Reg $C841 until it's
6787 * MSB (bit15) goes to 1 (indicating that the XAUI
6788 * workaround has completed), then continue on with
6789 * system initialization.
6790 */
6791 for (cnt1 = 0; cnt1 < 1000; cnt1++) {
6792 bnx2x_cl45_read(bp, phy,
6793 MDIO_PMA_DEVAD,
6794 MDIO_PMA_REG_8073_XAUI_WA, &val);
6795 if (val & (1<<15)) {
6796 DP(NETIF_MSG_LINK,
6797 "XAUI workaround has completed\n");
6798 return 0;
6799 }
6800 msleep(3);
6801 }
6802 break;
6803 }
6804 msleep(3);
6805 }
6806 DP(NETIF_MSG_LINK, "Warning: XAUI work-around timeout !!!\n");
6807 return -EINVAL;
6808 }
6809
6810 static void bnx2x_807x_force_10G(struct bnx2x *bp, struct bnx2x_phy *phy)
6811 {
6812 /* Force KR or KX */
6813 bnx2x_cl45_write(bp, phy,
6814 MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0x2040);
6815 bnx2x_cl45_write(bp, phy,
6816 MDIO_PMA_DEVAD, MDIO_PMA_REG_10G_CTRL2, 0x000b);
6817 bnx2x_cl45_write(bp, phy,
6818 MDIO_PMA_DEVAD, MDIO_PMA_REG_BCM_CTRL, 0x0000);
6819 bnx2x_cl45_write(bp, phy,
6820 MDIO_AN_DEVAD, MDIO_AN_REG_CTRL, 0x0000);
6821 }
6822
6823 static void bnx2x_8073_set_pause_cl37(struct link_params *params,
6824 struct bnx2x_phy *phy,
6825 struct link_vars *vars)
6826 {
6827 u16 cl37_val;
6828 struct bnx2x *bp = params->bp;
6829 bnx2x_cl45_read(bp, phy,
6830 MDIO_AN_DEVAD, MDIO_AN_REG_CL37_FC_LD, &cl37_val);
6831
6832 cl37_val &= ~MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH;
6833 /* Please refer to Table 28B-3 of 802.3ab-1999 spec. */
6834 bnx2x_calc_ieee_aneg_adv(phy, params, &vars->ieee_fc);
6835 if ((vars->ieee_fc &
6836 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_SYMMETRIC) ==
6837 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_SYMMETRIC) {
6838 cl37_val |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_SYMMETRIC;
6839 }
6840 if ((vars->ieee_fc &
6841 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) ==
6842 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) {
6843 cl37_val |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC;
6844 }
6845 if ((vars->ieee_fc &
6846 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) ==
6847 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) {
6848 cl37_val |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH;
6849 }
6850 DP(NETIF_MSG_LINK,
6851 "Ext phy AN advertize cl37 0x%x\n", cl37_val);
6852
6853 bnx2x_cl45_write(bp, phy,
6854 MDIO_AN_DEVAD, MDIO_AN_REG_CL37_FC_LD, cl37_val);
6855 msleep(500);
6856 }
6857
6858 static int bnx2x_8073_config_init(struct bnx2x_phy *phy,
6859 struct link_params *params,
6860 struct link_vars *vars)
6861 {
6862 struct bnx2x *bp = params->bp;
6863 u16 val = 0, tmp1;
6864 u8 gpio_port;
6865 DP(NETIF_MSG_LINK, "Init 8073\n");
6866
6867 if (CHIP_IS_E2(bp))
6868 gpio_port = BP_PATH(bp);
6869 else
6870 gpio_port = params->port;
6871 /* Restore normal power mode*/
6872 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
6873 MISC_REGISTERS_GPIO_OUTPUT_HIGH, gpio_port);
6874
6875 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
6876 MISC_REGISTERS_GPIO_OUTPUT_HIGH, gpio_port);
6877
6878 /* enable LASI */
6879 bnx2x_cl45_write(bp, phy,
6880 MDIO_PMA_DEVAD, MDIO_PMA_LASI_RXCTRL, (1<<2));
6881 bnx2x_cl45_write(bp, phy,
6882 MDIO_PMA_DEVAD, MDIO_PMA_LASI_CTRL, 0x0004);
6883
6884 bnx2x_8073_set_pause_cl37(params, phy, vars);
6885
6886 bnx2x_cl45_read(bp, phy,
6887 MDIO_PMA_DEVAD, MDIO_PMA_REG_M8051_MSGOUT_REG, &tmp1);
6888
6889 bnx2x_cl45_read(bp, phy,
6890 MDIO_PMA_DEVAD, MDIO_PMA_LASI_RXSTAT, &tmp1);
6891
6892 DP(NETIF_MSG_LINK, "Before rom RX_ALARM(port1): 0x%x\n", tmp1);
6893
6894 /* Swap polarity if required - Must be done only in non-1G mode */
6895 if (params->lane_config & PORT_HW_CFG_SWAP_PHY_POLARITY_ENABLED) {
6896 /* Configure the 8073 to swap _P and _N of the KR lines */
6897 DP(NETIF_MSG_LINK, "Swapping polarity for the 8073\n");
6898 /* 10G Rx/Tx and 1G Tx signal polarity swap */
6899 bnx2x_cl45_read(bp, phy,
6900 MDIO_PMA_DEVAD,
6901 MDIO_PMA_REG_8073_OPT_DIGITAL_CTRL, &val);
6902 bnx2x_cl45_write(bp, phy,
6903 MDIO_PMA_DEVAD,
6904 MDIO_PMA_REG_8073_OPT_DIGITAL_CTRL,
6905 (val | (3<<9)));
6906 }
6907
6908
6909 /* Enable CL37 BAM */
6910 if (REG_RD(bp, params->shmem_base +
6911 offsetof(struct shmem_region, dev_info.
6912 port_hw_config[params->port].default_cfg)) &
6913 PORT_HW_CFG_ENABLE_BAM_ON_KR_ENABLED) {
6914
6915 bnx2x_cl45_read(bp, phy,
6916 MDIO_AN_DEVAD,
6917 MDIO_AN_REG_8073_BAM, &val);
6918 bnx2x_cl45_write(bp, phy,
6919 MDIO_AN_DEVAD,
6920 MDIO_AN_REG_8073_BAM, val | 1);
6921 DP(NETIF_MSG_LINK, "Enable CL37 BAM on KR\n");
6922 }
6923 if (params->loopback_mode == LOOPBACK_EXT) {
6924 bnx2x_807x_force_10G(bp, phy);
6925 DP(NETIF_MSG_LINK, "Forced speed 10G on 807X\n");
6926 return 0;
6927 } else {
6928 bnx2x_cl45_write(bp, phy,
6929 MDIO_PMA_DEVAD, MDIO_PMA_REG_BCM_CTRL, 0x0002);
6930 }
6931 if (phy->req_line_speed != SPEED_AUTO_NEG) {
6932 if (phy->req_line_speed == SPEED_10000) {
6933 val = (1<<7);
6934 } else if (phy->req_line_speed == SPEED_2500) {
6935 val = (1<<5);
6936 /*
6937 * Note that 2.5G works only when used with 1G
6938 * advertisement
6939 */
6940 } else
6941 val = (1<<5);
6942 } else {
6943 val = 0;
6944 if (phy->speed_cap_mask &
6945 PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)
6946 val |= (1<<7);
6947
6948 /* Note that 2.5G works only when used with 1G advertisement */
6949 if (phy->speed_cap_mask &
6950 (PORT_HW_CFG_SPEED_CAPABILITY_D0_1G |
6951 PORT_HW_CFG_SPEED_CAPABILITY_D0_2_5G))
6952 val |= (1<<5);
6953 DP(NETIF_MSG_LINK, "807x autoneg val = 0x%x\n", val);
6954 }
6955
6956 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_ADV, val);
6957 bnx2x_cl45_read(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_8073_2_5G, &tmp1);
6958
6959 if (((phy->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_2_5G) &&
6960 (phy->req_line_speed == SPEED_AUTO_NEG)) ||
6961 (phy->req_line_speed == SPEED_2500)) {
6962 u16 phy_ver;
6963 /* Allow 2.5G for A1 and above */
6964 bnx2x_cl45_read(bp, phy,
6965 MDIO_PMA_DEVAD, MDIO_PMA_REG_8073_CHIP_REV,
6966 &phy_ver);
6967 DP(NETIF_MSG_LINK, "Add 2.5G\n");
6968 if (phy_ver > 0)
6969 tmp1 |= 1;
6970 else
6971 tmp1 &= 0xfffe;
6972 } else {
6973 DP(NETIF_MSG_LINK, "Disable 2.5G\n");
6974 tmp1 &= 0xfffe;
6975 }
6976
6977 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_8073_2_5G, tmp1);
6978 /* Add support for CL37 (passive mode) II */
6979
6980 bnx2x_cl45_read(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_CL37_FC_LD, &tmp1);
6981 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_CL37_FC_LD,
6982 (tmp1 | ((phy->req_duplex == DUPLEX_FULL) ?
6983 0x20 : 0x40)));
6984
6985 /* Add support for CL37 (passive mode) III */
6986 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_CL37_AN, 0x1000);
6987
6988 /*
6989 * The SNR will improve about 2db by changing BW and FEE main
6990 * tap. Rest commands are executed after link is up
6991 * Change FFE main cursor to 5 in EDC register
6992 */
6993 if (bnx2x_8073_is_snr_needed(bp, phy))
6994 bnx2x_cl45_write(bp, phy,
6995 MDIO_PMA_DEVAD, MDIO_PMA_REG_EDC_FFE_MAIN,
6996 0xFB0C);
6997
6998 /* Enable FEC (Forware Error Correction) Request in the AN */
6999 bnx2x_cl45_read(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_ADV2, &tmp1);
7000 tmp1 |= (1<<15);
7001 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_ADV2, tmp1);
7002
7003 bnx2x_ext_phy_set_pause(params, phy, vars);
7004
7005 /* Restart autoneg */
7006 msleep(500);
7007 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_CTRL, 0x1200);
7008 DP(NETIF_MSG_LINK, "807x Autoneg Restart: Advertise 1G=%x, 10G=%x\n",
7009 ((val & (1<<5)) > 0), ((val & (1<<7)) > 0));
7010 return 0;
7011 }
7012
7013 static u8 bnx2x_8073_read_status(struct bnx2x_phy *phy,
7014 struct link_params *params,
7015 struct link_vars *vars)
7016 {
7017 struct bnx2x *bp = params->bp;
7018 u8 link_up = 0;
7019 u16 val1, val2;
7020 u16 link_status = 0;
7021 u16 an1000_status = 0;
7022
7023 bnx2x_cl45_read(bp, phy,
7024 MDIO_PMA_DEVAD, MDIO_PMA_LASI_STAT, &val1);
7025
7026 DP(NETIF_MSG_LINK, "8703 LASI status 0x%x\n", val1);
7027
7028 /* clear the interrupt LASI status register */
7029 bnx2x_cl45_read(bp, phy,
7030 MDIO_PCS_DEVAD, MDIO_PCS_REG_STATUS, &val2);
7031 bnx2x_cl45_read(bp, phy,
7032 MDIO_PCS_DEVAD, MDIO_PCS_REG_STATUS, &val1);
7033 DP(NETIF_MSG_LINK, "807x PCS status 0x%x->0x%x\n", val2, val1);
7034 /* Clear MSG-OUT */
7035 bnx2x_cl45_read(bp, phy,
7036 MDIO_PMA_DEVAD, MDIO_PMA_REG_M8051_MSGOUT_REG, &val1);
7037
7038 /* Check the LASI */
7039 bnx2x_cl45_read(bp, phy,
7040 MDIO_PMA_DEVAD, MDIO_PMA_LASI_RXSTAT, &val2);
7041
7042 DP(NETIF_MSG_LINK, "KR 0x9003 0x%x\n", val2);
7043
7044 /* Check the link status */
7045 bnx2x_cl45_read(bp, phy,
7046 MDIO_PCS_DEVAD, MDIO_PCS_REG_STATUS, &val2);
7047 DP(NETIF_MSG_LINK, "KR PCS status 0x%x\n", val2);
7048
7049 bnx2x_cl45_read(bp, phy,
7050 MDIO_PMA_DEVAD, MDIO_PMA_REG_STATUS, &val2);
7051 bnx2x_cl45_read(bp, phy,
7052 MDIO_PMA_DEVAD, MDIO_PMA_REG_STATUS, &val1);
7053 link_up = ((val1 & 4) == 4);
7054 DP(NETIF_MSG_LINK, "PMA_REG_STATUS=0x%x\n", val1);
7055
7056 if (link_up &&
7057 ((phy->req_line_speed != SPEED_10000))) {
7058 if (bnx2x_8073_xaui_wa(bp, phy) != 0)
7059 return 0;
7060 }
7061 bnx2x_cl45_read(bp, phy,
7062 MDIO_AN_DEVAD, MDIO_AN_REG_LINK_STATUS, &an1000_status);
7063 bnx2x_cl45_read(bp, phy,
7064 MDIO_AN_DEVAD, MDIO_AN_REG_LINK_STATUS, &an1000_status);
7065
7066 /* Check the link status on 1.1.2 */
7067 bnx2x_cl45_read(bp, phy,
7068 MDIO_PMA_DEVAD, MDIO_PMA_REG_STATUS, &val2);
7069 bnx2x_cl45_read(bp, phy,
7070 MDIO_PMA_DEVAD, MDIO_PMA_REG_STATUS, &val1);
7071 DP(NETIF_MSG_LINK, "KR PMA status 0x%x->0x%x,"
7072 "an_link_status=0x%x\n", val2, val1, an1000_status);
7073
7074 link_up = (((val1 & 4) == 4) || (an1000_status & (1<<1)));
7075 if (link_up && bnx2x_8073_is_snr_needed(bp, phy)) {
7076 /*
7077 * The SNR will improve about 2dbby changing the BW and FEE main
7078 * tap. The 1st write to change FFE main tap is set before
7079 * restart AN. Change PLL Bandwidth in EDC register
7080 */
7081 bnx2x_cl45_write(bp, phy,
7082 MDIO_PMA_DEVAD, MDIO_PMA_REG_PLL_BANDWIDTH,
7083 0x26BC);
7084
7085 /* Change CDR Bandwidth in EDC register */
7086 bnx2x_cl45_write(bp, phy,
7087 MDIO_PMA_DEVAD, MDIO_PMA_REG_CDR_BANDWIDTH,
7088 0x0333);
7089 }
7090 bnx2x_cl45_read(bp, phy,
7091 MDIO_PMA_DEVAD, MDIO_PMA_REG_8073_SPEED_LINK_STATUS,
7092 &link_status);
7093
7094 /* Bits 0..2 --> speed detected, bits 13..15--> link is down */
7095 if ((link_status & (1<<2)) && (!(link_status & (1<<15)))) {
7096 link_up = 1;
7097 vars->line_speed = SPEED_10000;
7098 DP(NETIF_MSG_LINK, "port %x: External link up in 10G\n",
7099 params->port);
7100 } else if ((link_status & (1<<1)) && (!(link_status & (1<<14)))) {
7101 link_up = 1;
7102 vars->line_speed = SPEED_2500;
7103 DP(NETIF_MSG_LINK, "port %x: External link up in 2.5G\n",
7104 params->port);
7105 } else if ((link_status & (1<<0)) && (!(link_status & (1<<13)))) {
7106 link_up = 1;
7107 vars->line_speed = SPEED_1000;
7108 DP(NETIF_MSG_LINK, "port %x: External link up in 1G\n",
7109 params->port);
7110 } else {
7111 link_up = 0;
7112 DP(NETIF_MSG_LINK, "port %x: External link is down\n",
7113 params->port);
7114 }
7115
7116 if (link_up) {
7117 /* Swap polarity if required */
7118 if (params->lane_config &
7119 PORT_HW_CFG_SWAP_PHY_POLARITY_ENABLED) {
7120 /* Configure the 8073 to swap P and N of the KR lines */
7121 bnx2x_cl45_read(bp, phy,
7122 MDIO_XS_DEVAD,
7123 MDIO_XS_REG_8073_RX_CTRL_PCIE, &val1);
7124 /*
7125 * Set bit 3 to invert Rx in 1G mode and clear this bit
7126 * when it`s in 10G mode.
7127 */
7128 if (vars->line_speed == SPEED_1000) {
7129 DP(NETIF_MSG_LINK, "Swapping 1G polarity for"
7130 "the 8073\n");
7131 val1 |= (1<<3);
7132 } else
7133 val1 &= ~(1<<3);
7134
7135 bnx2x_cl45_write(bp, phy,
7136 MDIO_XS_DEVAD,
7137 MDIO_XS_REG_8073_RX_CTRL_PCIE,
7138 val1);
7139 }
7140 bnx2x_ext_phy_10G_an_resolve(bp, phy, vars);
7141 bnx2x_8073_resolve_fc(phy, params, vars);
7142 vars->duplex = DUPLEX_FULL;
7143 }
7144 return link_up;
7145 }
7146
7147 static void bnx2x_8073_link_reset(struct bnx2x_phy *phy,
7148 struct link_params *params)
7149 {
7150 struct bnx2x *bp = params->bp;
7151 u8 gpio_port;
7152 if (CHIP_IS_E2(bp))
7153 gpio_port = BP_PATH(bp);
7154 else
7155 gpio_port = params->port;
7156 DP(NETIF_MSG_LINK, "Setting 8073 port %d into low power mode\n",
7157 gpio_port);
7158 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
7159 MISC_REGISTERS_GPIO_OUTPUT_LOW,
7160 gpio_port);
7161 }
7162
7163 /******************************************************************/
7164 /* BCM8705 PHY SECTION */
7165 /******************************************************************/
7166 static int bnx2x_8705_config_init(struct bnx2x_phy *phy,
7167 struct link_params *params,
7168 struct link_vars *vars)
7169 {
7170 struct bnx2x *bp = params->bp;
7171 DP(NETIF_MSG_LINK, "init 8705\n");
7172 /* Restore normal power mode*/
7173 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
7174 MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port);
7175 /* HW reset */
7176 bnx2x_ext_phy_hw_reset(bp, params->port);
7177 bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0xa040);
7178 bnx2x_wait_reset_complete(bp, phy, params);
7179
7180 bnx2x_cl45_write(bp, phy,
7181 MDIO_PMA_DEVAD, MDIO_PMA_REG_MISC_CTRL, 0x8288);
7182 bnx2x_cl45_write(bp, phy,
7183 MDIO_PMA_DEVAD, MDIO_PMA_REG_PHY_IDENTIFIER, 0x7fbf);
7184 bnx2x_cl45_write(bp, phy,
7185 MDIO_PMA_DEVAD, MDIO_PMA_REG_CMU_PLL_BYPASS, 0x0100);
7186 bnx2x_cl45_write(bp, phy,
7187 MDIO_WIS_DEVAD, MDIO_WIS_REG_LASI_CNTL, 0x1);
7188 /* BCM8705 doesn't have microcode, hence the 0 */
7189 bnx2x_save_spirom_version(bp, params->port, params->shmem_base, 0);
7190 return 0;
7191 }
7192
7193 static u8 bnx2x_8705_read_status(struct bnx2x_phy *phy,
7194 struct link_params *params,
7195 struct link_vars *vars)
7196 {
7197 u8 link_up = 0;
7198 u16 val1, rx_sd;
7199 struct bnx2x *bp = params->bp;
7200 DP(NETIF_MSG_LINK, "read status 8705\n");
7201 bnx2x_cl45_read(bp, phy,
7202 MDIO_WIS_DEVAD, MDIO_WIS_REG_LASI_STATUS, &val1);
7203 DP(NETIF_MSG_LINK, "8705 LASI status 0x%x\n", val1);
7204
7205 bnx2x_cl45_read(bp, phy,
7206 MDIO_WIS_DEVAD, MDIO_WIS_REG_LASI_STATUS, &val1);
7207 DP(NETIF_MSG_LINK, "8705 LASI status 0x%x\n", val1);
7208
7209 bnx2x_cl45_read(bp, phy,
7210 MDIO_PMA_DEVAD, MDIO_PMA_REG_RX_SD, &rx_sd);
7211
7212 bnx2x_cl45_read(bp, phy,
7213 MDIO_PMA_DEVAD, 0xc809, &val1);
7214 bnx2x_cl45_read(bp, phy,
7215 MDIO_PMA_DEVAD, 0xc809, &val1);
7216
7217 DP(NETIF_MSG_LINK, "8705 1.c809 val=0x%x\n", val1);
7218 link_up = ((rx_sd & 0x1) && (val1 & (1<<9)) && ((val1 & (1<<8)) == 0));
7219 if (link_up) {
7220 vars->line_speed = SPEED_10000;
7221 bnx2x_ext_phy_resolve_fc(phy, params, vars);
7222 }
7223 return link_up;
7224 }
7225
7226 /******************************************************************/
7227 /* SFP+ module Section */
7228 /******************************************************************/
7229 static void bnx2x_set_disable_pmd_transmit(struct link_params *params,
7230 struct bnx2x_phy *phy,
7231 u8 pmd_dis)
7232 {
7233 struct bnx2x *bp = params->bp;
7234 /*
7235 * Disable transmitter only for bootcodes which can enable it afterwards
7236 * (for D3 link)
7237 */
7238 if (pmd_dis) {
7239 if (params->feature_config_flags &
7240 FEATURE_CONFIG_BC_SUPPORTS_SFP_TX_DISABLED)
7241 DP(NETIF_MSG_LINK, "Disabling PMD transmitter\n");
7242 else {
7243 DP(NETIF_MSG_LINK, "NOT disabling PMD transmitter\n");
7244 return;
7245 }
7246 } else
7247 DP(NETIF_MSG_LINK, "Enabling PMD transmitter\n");
7248 bnx2x_cl45_write(bp, phy,
7249 MDIO_PMA_DEVAD,
7250 MDIO_PMA_REG_TX_DISABLE, pmd_dis);
7251 }
7252
7253 static u8 bnx2x_get_gpio_port(struct link_params *params)
7254 {
7255 u8 gpio_port;
7256 u32 swap_val, swap_override;
7257 struct bnx2x *bp = params->bp;
7258 if (CHIP_IS_E2(bp))
7259 gpio_port = BP_PATH(bp);
7260 else
7261 gpio_port = params->port;
7262 swap_val = REG_RD(bp, NIG_REG_PORT_SWAP);
7263 swap_override = REG_RD(bp, NIG_REG_STRAP_OVERRIDE);
7264 return gpio_port ^ (swap_val && swap_override);
7265 }
7266
7267 static void bnx2x_sfp_e1e2_set_transmitter(struct link_params *params,
7268 struct bnx2x_phy *phy,
7269 u8 tx_en)
7270 {
7271 u16 val;
7272 u8 port = params->port;
7273 struct bnx2x *bp = params->bp;
7274 u32 tx_en_mode;
7275
7276 /* Disable/Enable transmitter ( TX laser of the SFP+ module.)*/
7277 tx_en_mode = REG_RD(bp, params->shmem_base +
7278 offsetof(struct shmem_region,
7279 dev_info.port_hw_config[port].sfp_ctrl)) &
7280 PORT_HW_CFG_TX_LASER_MASK;
7281 DP(NETIF_MSG_LINK, "Setting transmitter tx_en=%x for port %x "
7282 "mode = %x\n", tx_en, port, tx_en_mode);
7283 switch (tx_en_mode) {
7284 case PORT_HW_CFG_TX_LASER_MDIO:
7285
7286 bnx2x_cl45_read(bp, phy,
7287 MDIO_PMA_DEVAD,
7288 MDIO_PMA_REG_PHY_IDENTIFIER,
7289 &val);
7290
7291 if (tx_en)
7292 val &= ~(1<<15);
7293 else
7294 val |= (1<<15);
7295
7296 bnx2x_cl45_write(bp, phy,
7297 MDIO_PMA_DEVAD,
7298 MDIO_PMA_REG_PHY_IDENTIFIER,
7299 val);
7300 break;
7301 case PORT_HW_CFG_TX_LASER_GPIO0:
7302 case PORT_HW_CFG_TX_LASER_GPIO1:
7303 case PORT_HW_CFG_TX_LASER_GPIO2:
7304 case PORT_HW_CFG_TX_LASER_GPIO3:
7305 {
7306 u16 gpio_pin;
7307 u8 gpio_port, gpio_mode;
7308 if (tx_en)
7309 gpio_mode = MISC_REGISTERS_GPIO_OUTPUT_HIGH;
7310 else
7311 gpio_mode = MISC_REGISTERS_GPIO_OUTPUT_LOW;
7312
7313 gpio_pin = tx_en_mode - PORT_HW_CFG_TX_LASER_GPIO0;
7314 gpio_port = bnx2x_get_gpio_port(params);
7315 bnx2x_set_gpio(bp, gpio_pin, gpio_mode, gpio_port);
7316 break;
7317 }
7318 default:
7319 DP(NETIF_MSG_LINK, "Invalid TX_LASER_MDIO 0x%x\n", tx_en_mode);
7320 break;
7321 }
7322 }
7323
7324 static void bnx2x_sfp_set_transmitter(struct link_params *params,
7325 struct bnx2x_phy *phy,
7326 u8 tx_en)
7327 {
7328 struct bnx2x *bp = params->bp;
7329 DP(NETIF_MSG_LINK, "Setting SFP+ transmitter to %d\n", tx_en);
7330 if (CHIP_IS_E3(bp))
7331 bnx2x_sfp_e3_set_transmitter(params, phy, tx_en);
7332 else
7333 bnx2x_sfp_e1e2_set_transmitter(params, phy, tx_en);
7334 }
7335
7336 static int bnx2x_8726_read_sfp_module_eeprom(struct bnx2x_phy *phy,
7337 struct link_params *params,
7338 u16 addr, u8 byte_cnt, u8 *o_buf)
7339 {
7340 struct bnx2x *bp = params->bp;
7341 u16 val = 0;
7342 u16 i;
7343 if (byte_cnt > 16) {
7344 DP(NETIF_MSG_LINK, "Reading from eeprom is"
7345 " is limited to 0xf\n");
7346 return -EINVAL;
7347 }
7348 /* Set the read command byte count */
7349 bnx2x_cl45_write(bp, phy,
7350 MDIO_PMA_DEVAD, MDIO_PMA_REG_SFP_TWO_WIRE_BYTE_CNT,
7351 (byte_cnt | 0xa000));
7352
7353 /* Set the read command address */
7354 bnx2x_cl45_write(bp, phy,
7355 MDIO_PMA_DEVAD, MDIO_PMA_REG_SFP_TWO_WIRE_MEM_ADDR,
7356 addr);
7357
7358 /* Activate read command */
7359 bnx2x_cl45_write(bp, phy,
7360 MDIO_PMA_DEVAD, MDIO_PMA_REG_SFP_TWO_WIRE_CTRL,
7361 0x2c0f);
7362
7363 /* Wait up to 500us for command complete status */
7364 for (i = 0; i < 100; i++) {
7365 bnx2x_cl45_read(bp, phy,
7366 MDIO_PMA_DEVAD,
7367 MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val);
7368 if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) ==
7369 MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_COMPLETE)
7370 break;
7371 udelay(5);
7372 }
7373
7374 if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) !=
7375 MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_COMPLETE) {
7376 DP(NETIF_MSG_LINK,
7377 "Got bad status 0x%x when reading from SFP+ EEPROM\n",
7378 (val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK));
7379 return -EINVAL;
7380 }
7381
7382 /* Read the buffer */
7383 for (i = 0; i < byte_cnt; i++) {
7384 bnx2x_cl45_read(bp, phy,
7385 MDIO_PMA_DEVAD,
7386 MDIO_PMA_REG_8726_TWO_WIRE_DATA_BUF + i, &val);
7387 o_buf[i] = (u8)(val & MDIO_PMA_REG_8726_TWO_WIRE_DATA_MASK);
7388 }
7389
7390 for (i = 0; i < 100; i++) {
7391 bnx2x_cl45_read(bp, phy,
7392 MDIO_PMA_DEVAD,
7393 MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val);
7394 if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) ==
7395 MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_IDLE)
7396 return 0;
7397 msleep(1);
7398 }
7399 return -EINVAL;
7400 }
7401
7402 static int bnx2x_warpcore_read_sfp_module_eeprom(struct bnx2x_phy *phy,
7403 struct link_params *params,
7404 u16 addr, u8 byte_cnt,
7405 u8 *o_buf)
7406 {
7407 int rc = 0;
7408 u8 i, j = 0, cnt = 0;
7409 u32 data_array[4];
7410 u16 addr32;
7411 struct bnx2x *bp = params->bp;
7412 /*DP(NETIF_MSG_LINK, "bnx2x_direct_read_sfp_module_eeprom:"
7413 " addr %d, cnt %d\n",
7414 addr, byte_cnt);*/
7415 if (byte_cnt > 16) {
7416 DP(NETIF_MSG_LINK, "Reading from eeprom is"
7417 " is limited to 16 bytes\n");
7418 return -EINVAL;
7419 }
7420
7421 /* 4 byte aligned address */
7422 addr32 = addr & (~0x3);
7423 do {
7424 rc = bnx2x_bsc_read(params, phy, 0xa0, addr32, 0, byte_cnt,
7425 data_array);
7426 } while ((rc != 0) && (++cnt < I2C_WA_RETRY_CNT));
7427
7428 if (rc == 0) {
7429 for (i = (addr - addr32); i < byte_cnt + (addr - addr32); i++) {
7430 o_buf[j] = *((u8 *)data_array + i);
7431 j++;
7432 }
7433 }
7434
7435 return rc;
7436 }
7437
7438 static int bnx2x_8727_read_sfp_module_eeprom(struct bnx2x_phy *phy,
7439 struct link_params *params,
7440 u16 addr, u8 byte_cnt, u8 *o_buf)
7441 {
7442 struct bnx2x *bp = params->bp;
7443 u16 val, i;
7444
7445 if (byte_cnt > 16) {
7446 DP(NETIF_MSG_LINK, "Reading from eeprom is"
7447 " is limited to 0xf\n");
7448 return -EINVAL;
7449 }
7450
7451 /* Need to read from 1.8000 to clear it */
7452 bnx2x_cl45_read(bp, phy,
7453 MDIO_PMA_DEVAD,
7454 MDIO_PMA_REG_SFP_TWO_WIRE_CTRL,
7455 &val);
7456
7457 /* Set the read command byte count */
7458 bnx2x_cl45_write(bp, phy,
7459 MDIO_PMA_DEVAD,
7460 MDIO_PMA_REG_SFP_TWO_WIRE_BYTE_CNT,
7461 ((byte_cnt < 2) ? 2 : byte_cnt));
7462
7463 /* Set the read command address */
7464 bnx2x_cl45_write(bp, phy,
7465 MDIO_PMA_DEVAD,
7466 MDIO_PMA_REG_SFP_TWO_WIRE_MEM_ADDR,
7467 addr);
7468 /* Set the destination address */
7469 bnx2x_cl45_write(bp, phy,
7470 MDIO_PMA_DEVAD,
7471 0x8004,
7472 MDIO_PMA_REG_8727_TWO_WIRE_DATA_BUF);
7473
7474 /* Activate read command */
7475 bnx2x_cl45_write(bp, phy,
7476 MDIO_PMA_DEVAD,
7477 MDIO_PMA_REG_SFP_TWO_WIRE_CTRL,
7478 0x8002);
7479 /*
7480 * Wait appropriate time for two-wire command to finish before
7481 * polling the status register
7482 */
7483 msleep(1);
7484
7485 /* Wait up to 500us for command complete status */
7486 for (i = 0; i < 100; i++) {
7487 bnx2x_cl45_read(bp, phy,
7488 MDIO_PMA_DEVAD,
7489 MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val);
7490 if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) ==
7491 MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_COMPLETE)
7492 break;
7493 udelay(5);
7494 }
7495
7496 if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) !=
7497 MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_COMPLETE) {
7498 DP(NETIF_MSG_LINK,
7499 "Got bad status 0x%x when reading from SFP+ EEPROM\n",
7500 (val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK));
7501 return -EFAULT;
7502 }
7503
7504 /* Read the buffer */
7505 for (i = 0; i < byte_cnt; i++) {
7506 bnx2x_cl45_read(bp, phy,
7507 MDIO_PMA_DEVAD,
7508 MDIO_PMA_REG_8727_TWO_WIRE_DATA_BUF + i, &val);
7509 o_buf[i] = (u8)(val & MDIO_PMA_REG_8727_TWO_WIRE_DATA_MASK);
7510 }
7511
7512 for (i = 0; i < 100; i++) {
7513 bnx2x_cl45_read(bp, phy,
7514 MDIO_PMA_DEVAD,
7515 MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val);
7516 if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) ==
7517 MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_IDLE)
7518 return 0;
7519 msleep(1);
7520 }
7521
7522 return -EINVAL;
7523 }
7524
7525 int bnx2x_read_sfp_module_eeprom(struct bnx2x_phy *phy,
7526 struct link_params *params, u16 addr,
7527 u8 byte_cnt, u8 *o_buf)
7528 {
7529 int rc = -EINVAL;
7530 switch (phy->type) {
7531 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726:
7532 rc = bnx2x_8726_read_sfp_module_eeprom(phy, params, addr,
7533 byte_cnt, o_buf);
7534 break;
7535 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
7536 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8722:
7537 rc = bnx2x_8727_read_sfp_module_eeprom(phy, params, addr,
7538 byte_cnt, o_buf);
7539 break;
7540 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT:
7541 rc = bnx2x_warpcore_read_sfp_module_eeprom(phy, params, addr,
7542 byte_cnt, o_buf);
7543 break;
7544 }
7545 return rc;
7546 }
7547
7548 static int bnx2x_get_edc_mode(struct bnx2x_phy *phy,
7549 struct link_params *params,
7550 u16 *edc_mode)
7551 {
7552 struct bnx2x *bp = params->bp;
7553 u32 sync_offset = 0, phy_idx, media_types;
7554 u8 val, check_limiting_mode = 0;
7555 *edc_mode = EDC_MODE_LIMITING;
7556
7557 phy->media_type = ETH_PHY_UNSPECIFIED;
7558 /* First check for copper cable */
7559 if (bnx2x_read_sfp_module_eeprom(phy,
7560 params,
7561 SFP_EEPROM_CON_TYPE_ADDR,
7562 1,
7563 &val) != 0) {
7564 DP(NETIF_MSG_LINK, "Failed to read from SFP+ module EEPROM\n");
7565 return -EINVAL;
7566 }
7567
7568 switch (val) {
7569 case SFP_EEPROM_CON_TYPE_VAL_COPPER:
7570 {
7571 u8 copper_module_type;
7572 phy->media_type = ETH_PHY_DA_TWINAX;
7573 /*
7574 * Check if its active cable (includes SFP+ module)
7575 * of passive cable
7576 */
7577 if (bnx2x_read_sfp_module_eeprom(phy,
7578 params,
7579 SFP_EEPROM_FC_TX_TECH_ADDR,
7580 1,
7581 &copper_module_type) != 0) {
7582 DP(NETIF_MSG_LINK,
7583 "Failed to read copper-cable-type"
7584 " from SFP+ EEPROM\n");
7585 return -EINVAL;
7586 }
7587
7588 if (copper_module_type &
7589 SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_ACTIVE) {
7590 DP(NETIF_MSG_LINK, "Active Copper cable detected\n");
7591 check_limiting_mode = 1;
7592 } else if (copper_module_type &
7593 SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_PASSIVE) {
7594 DP(NETIF_MSG_LINK, "Passive Copper"
7595 " cable detected\n");
7596 *edc_mode =
7597 EDC_MODE_PASSIVE_DAC;
7598 } else {
7599 DP(NETIF_MSG_LINK, "Unknown copper-cable-"
7600 "type 0x%x !!!\n", copper_module_type);
7601 return -EINVAL;
7602 }
7603 break;
7604 }
7605 case SFP_EEPROM_CON_TYPE_VAL_LC:
7606 phy->media_type = ETH_PHY_SFP_FIBER;
7607 DP(NETIF_MSG_LINK, "Optic module detected\n");
7608 check_limiting_mode = 1;
7609 break;
7610 default:
7611 DP(NETIF_MSG_LINK, "Unable to determine module type 0x%x !!!\n",
7612 val);
7613 return -EINVAL;
7614 }
7615 sync_offset = params->shmem_base +
7616 offsetof(struct shmem_region,
7617 dev_info.port_hw_config[params->port].media_type);
7618 media_types = REG_RD(bp, sync_offset);
7619 /* Update media type for non-PMF sync */
7620 for (phy_idx = INT_PHY; phy_idx < MAX_PHYS; phy_idx++) {
7621 if (&(params->phy[phy_idx]) == phy) {
7622 media_types &= ~(PORT_HW_CFG_MEDIA_TYPE_PHY0_MASK <<
7623 (PORT_HW_CFG_MEDIA_TYPE_PHY1_SHIFT * phy_idx));
7624 media_types |= ((phy->media_type &
7625 PORT_HW_CFG_MEDIA_TYPE_PHY0_MASK) <<
7626 (PORT_HW_CFG_MEDIA_TYPE_PHY1_SHIFT * phy_idx));
7627 break;
7628 }
7629 }
7630 REG_WR(bp, sync_offset, media_types);
7631 if (check_limiting_mode) {
7632 u8 options[SFP_EEPROM_OPTIONS_SIZE];
7633 if (bnx2x_read_sfp_module_eeprom(phy,
7634 params,
7635 SFP_EEPROM_OPTIONS_ADDR,
7636 SFP_EEPROM_OPTIONS_SIZE,
7637 options) != 0) {
7638 DP(NETIF_MSG_LINK, "Failed to read Option"
7639 " field from module EEPROM\n");
7640 return -EINVAL;
7641 }
7642 if ((options[0] & SFP_EEPROM_OPTIONS_LINEAR_RX_OUT_MASK))
7643 *edc_mode = EDC_MODE_LINEAR;
7644 else
7645 *edc_mode = EDC_MODE_LIMITING;
7646 }
7647 DP(NETIF_MSG_LINK, "EDC mode is set to 0x%x\n", *edc_mode);
7648 return 0;
7649 }
7650 /*
7651 * This function read the relevant field from the module (SFP+), and verify it
7652 * is compliant with this board
7653 */
7654 static int bnx2x_verify_sfp_module(struct bnx2x_phy *phy,
7655 struct link_params *params)
7656 {
7657 struct bnx2x *bp = params->bp;
7658 u32 val, cmd;
7659 u32 fw_resp, fw_cmd_param;
7660 char vendor_name[SFP_EEPROM_VENDOR_NAME_SIZE+1];
7661 char vendor_pn[SFP_EEPROM_PART_NO_SIZE+1];
7662 phy->flags &= ~FLAGS_SFP_NOT_APPROVED;
7663 val = REG_RD(bp, params->shmem_base +
7664 offsetof(struct shmem_region, dev_info.
7665 port_feature_config[params->port].config));
7666 if ((val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) ==
7667 PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_NO_ENFORCEMENT) {
7668 DP(NETIF_MSG_LINK, "NOT enforcing module verification\n");
7669 return 0;
7670 }
7671
7672 if (params->feature_config_flags &
7673 FEATURE_CONFIG_BC_SUPPORTS_DUAL_PHY_OPT_MDL_VRFY) {
7674 /* Use specific phy request */
7675 cmd = DRV_MSG_CODE_VRFY_SPECIFIC_PHY_OPT_MDL;
7676 } else if (params->feature_config_flags &
7677 FEATURE_CONFIG_BC_SUPPORTS_OPT_MDL_VRFY) {
7678 /* Use first phy request only in case of non-dual media*/
7679 if (DUAL_MEDIA(params)) {
7680 DP(NETIF_MSG_LINK, "FW does not support OPT MDL "
7681 "verification\n");
7682 return -EINVAL;
7683 }
7684 cmd = DRV_MSG_CODE_VRFY_FIRST_PHY_OPT_MDL;
7685 } else {
7686 /* No support in OPT MDL detection */
7687 DP(NETIF_MSG_LINK, "FW does not support OPT MDL "
7688 "verification\n");
7689 return -EINVAL;
7690 }
7691
7692 fw_cmd_param = FW_PARAM_SET(phy->addr, phy->type, phy->mdio_ctrl);
7693 fw_resp = bnx2x_fw_command(bp, cmd, fw_cmd_param);
7694 if (fw_resp == FW_MSG_CODE_VRFY_OPT_MDL_SUCCESS) {
7695 DP(NETIF_MSG_LINK, "Approved module\n");
7696 return 0;
7697 }
7698
7699 /* format the warning message */
7700 if (bnx2x_read_sfp_module_eeprom(phy,
7701 params,
7702 SFP_EEPROM_VENDOR_NAME_ADDR,
7703 SFP_EEPROM_VENDOR_NAME_SIZE,
7704 (u8 *)vendor_name))
7705 vendor_name[0] = '\0';
7706 else
7707 vendor_name[SFP_EEPROM_VENDOR_NAME_SIZE] = '\0';
7708 if (bnx2x_read_sfp_module_eeprom(phy,
7709 params,
7710 SFP_EEPROM_PART_NO_ADDR,
7711 SFP_EEPROM_PART_NO_SIZE,
7712 (u8 *)vendor_pn))
7713 vendor_pn[0] = '\0';
7714 else
7715 vendor_pn[SFP_EEPROM_PART_NO_SIZE] = '\0';
7716
7717 netdev_err(bp->dev, "Warning: Unqualified SFP+ module detected,"
7718 " Port %d from %s part number %s\n",
7719 params->port, vendor_name, vendor_pn);
7720 phy->flags |= FLAGS_SFP_NOT_APPROVED;
7721 return -EINVAL;
7722 }
7723
7724 static int bnx2x_wait_for_sfp_module_initialized(struct bnx2x_phy *phy,
7725 struct link_params *params)
7726
7727 {
7728 u8 val;
7729 struct bnx2x *bp = params->bp;
7730 u16 timeout;
7731 /*
7732 * Initialization time after hot-plug may take up to 300ms for
7733 * some phys type ( e.g. JDSU )
7734 */
7735
7736 for (timeout = 0; timeout < 60; timeout++) {
7737 if (bnx2x_read_sfp_module_eeprom(phy, params, 1, 1, &val)
7738 == 0) {
7739 DP(NETIF_MSG_LINK, "SFP+ module initialization "
7740 "took %d ms\n", timeout * 5);
7741 return 0;
7742 }
7743 msleep(5);
7744 }
7745 return -EINVAL;
7746 }
7747
7748 static void bnx2x_8727_power_module(struct bnx2x *bp,
7749 struct bnx2x_phy *phy,
7750 u8 is_power_up) {
7751 /* Make sure GPIOs are not using for LED mode */
7752 u16 val;
7753 /*
7754 * In the GPIO register, bit 4 is use to determine if the GPIOs are
7755 * operating as INPUT or as OUTPUT. Bit 1 is for input, and 0 for
7756 * output
7757 * Bits 0-1 determine the GPIOs value for OUTPUT in case bit 4 val is 0
7758 * Bits 8-9 determine the GPIOs value for INPUT in case bit 4 val is 1
7759 * where the 1st bit is the over-current(only input), and 2nd bit is
7760 * for power( only output )
7761 *
7762 * In case of NOC feature is disabled and power is up, set GPIO control
7763 * as input to enable listening of over-current indication
7764 */
7765 if (phy->flags & FLAGS_NOC)
7766 return;
7767 if (is_power_up)
7768 val = (1<<4);
7769 else
7770 /*
7771 * Set GPIO control to OUTPUT, and set the power bit
7772 * to according to the is_power_up
7773 */
7774 val = (1<<1);
7775
7776 bnx2x_cl45_write(bp, phy,
7777 MDIO_PMA_DEVAD,
7778 MDIO_PMA_REG_8727_GPIO_CTRL,
7779 val);
7780 }
7781
7782 static int bnx2x_8726_set_limiting_mode(struct bnx2x *bp,
7783 struct bnx2x_phy *phy,
7784 u16 edc_mode)
7785 {
7786 u16 cur_limiting_mode;
7787
7788 bnx2x_cl45_read(bp, phy,
7789 MDIO_PMA_DEVAD,
7790 MDIO_PMA_REG_ROM_VER2,
7791 &cur_limiting_mode);
7792 DP(NETIF_MSG_LINK, "Current Limiting mode is 0x%x\n",
7793 cur_limiting_mode);
7794
7795 if (edc_mode == EDC_MODE_LIMITING) {
7796 DP(NETIF_MSG_LINK, "Setting LIMITING MODE\n");
7797 bnx2x_cl45_write(bp, phy,
7798 MDIO_PMA_DEVAD,
7799 MDIO_PMA_REG_ROM_VER2,
7800 EDC_MODE_LIMITING);
7801 } else { /* LRM mode ( default )*/
7802
7803 DP(NETIF_MSG_LINK, "Setting LRM MODE\n");
7804
7805 /*
7806 * Changing to LRM mode takes quite few seconds. So do it only
7807 * if current mode is limiting (default is LRM)
7808 */
7809 if (cur_limiting_mode != EDC_MODE_LIMITING)
7810 return 0;
7811
7812 bnx2x_cl45_write(bp, phy,
7813 MDIO_PMA_DEVAD,
7814 MDIO_PMA_REG_LRM_MODE,
7815 0);
7816 bnx2x_cl45_write(bp, phy,
7817 MDIO_PMA_DEVAD,
7818 MDIO_PMA_REG_ROM_VER2,
7819 0x128);
7820 bnx2x_cl45_write(bp, phy,
7821 MDIO_PMA_DEVAD,
7822 MDIO_PMA_REG_MISC_CTRL0,
7823 0x4008);
7824 bnx2x_cl45_write(bp, phy,
7825 MDIO_PMA_DEVAD,
7826 MDIO_PMA_REG_LRM_MODE,
7827 0xaaaa);
7828 }
7829 return 0;
7830 }
7831
7832 static int bnx2x_8727_set_limiting_mode(struct bnx2x *bp,
7833 struct bnx2x_phy *phy,
7834 u16 edc_mode)
7835 {
7836 u16 phy_identifier;
7837 u16 rom_ver2_val;
7838 bnx2x_cl45_read(bp, phy,
7839 MDIO_PMA_DEVAD,
7840 MDIO_PMA_REG_PHY_IDENTIFIER,
7841 &phy_identifier);
7842
7843 bnx2x_cl45_write(bp, phy,
7844 MDIO_PMA_DEVAD,
7845 MDIO_PMA_REG_PHY_IDENTIFIER,
7846 (phy_identifier & ~(1<<9)));
7847
7848 bnx2x_cl45_read(bp, phy,
7849 MDIO_PMA_DEVAD,
7850 MDIO_PMA_REG_ROM_VER2,
7851 &rom_ver2_val);
7852 /* Keep the MSB 8-bits, and set the LSB 8-bits with the edc_mode */
7853 bnx2x_cl45_write(bp, phy,
7854 MDIO_PMA_DEVAD,
7855 MDIO_PMA_REG_ROM_VER2,
7856 (rom_ver2_val & 0xff00) | (edc_mode & 0x00ff));
7857
7858 bnx2x_cl45_write(bp, phy,
7859 MDIO_PMA_DEVAD,
7860 MDIO_PMA_REG_PHY_IDENTIFIER,
7861 (phy_identifier | (1<<9)));
7862
7863 return 0;
7864 }
7865
7866 static void bnx2x_8727_specific_func(struct bnx2x_phy *phy,
7867 struct link_params *params,
7868 u32 action)
7869 {
7870 struct bnx2x *bp = params->bp;
7871
7872 switch (action) {
7873 case DISABLE_TX:
7874 bnx2x_sfp_set_transmitter(params, phy, 0);
7875 break;
7876 case ENABLE_TX:
7877 if (!(phy->flags & FLAGS_SFP_NOT_APPROVED))
7878 bnx2x_sfp_set_transmitter(params, phy, 1);
7879 break;
7880 default:
7881 DP(NETIF_MSG_LINK, "Function 0x%x not supported by 8727\n",
7882 action);
7883 return;
7884 }
7885 }
7886
7887 static void bnx2x_set_e1e2_module_fault_led(struct link_params *params,
7888 u8 gpio_mode)
7889 {
7890 struct bnx2x *bp = params->bp;
7891
7892 u32 fault_led_gpio = REG_RD(bp, params->shmem_base +
7893 offsetof(struct shmem_region,
7894 dev_info.port_hw_config[params->port].sfp_ctrl)) &
7895 PORT_HW_CFG_FAULT_MODULE_LED_MASK;
7896 switch (fault_led_gpio) {
7897 case PORT_HW_CFG_FAULT_MODULE_LED_DISABLED:
7898 return;
7899 case PORT_HW_CFG_FAULT_MODULE_LED_GPIO0:
7900 case PORT_HW_CFG_FAULT_MODULE_LED_GPIO1:
7901 case PORT_HW_CFG_FAULT_MODULE_LED_GPIO2:
7902 case PORT_HW_CFG_FAULT_MODULE_LED_GPIO3:
7903 {
7904 u8 gpio_port = bnx2x_get_gpio_port(params);
7905 u16 gpio_pin = fault_led_gpio -
7906 PORT_HW_CFG_FAULT_MODULE_LED_GPIO0;
7907 DP(NETIF_MSG_LINK, "Set fault module-detected led "
7908 "pin %x port %x mode %x\n",
7909 gpio_pin, gpio_port, gpio_mode);
7910 bnx2x_set_gpio(bp, gpio_pin, gpio_mode, gpio_port);
7911 }
7912 break;
7913 default:
7914 DP(NETIF_MSG_LINK, "Error: Invalid fault led mode 0x%x\n",
7915 fault_led_gpio);
7916 }
7917 }
7918
7919 static void bnx2x_set_e3_module_fault_led(struct link_params *params,
7920 u8 gpio_mode)
7921 {
7922 u32 pin_cfg;
7923 u8 port = params->port;
7924 struct bnx2x *bp = params->bp;
7925 pin_cfg = (REG_RD(bp, params->shmem_base +
7926 offsetof(struct shmem_region,
7927 dev_info.port_hw_config[port].e3_sfp_ctrl)) &
7928 PORT_HW_CFG_E3_FAULT_MDL_LED_MASK) >>
7929 PORT_HW_CFG_E3_FAULT_MDL_LED_SHIFT;
7930 DP(NETIF_MSG_LINK, "Setting Fault LED to %d using pin cfg %d\n",
7931 gpio_mode, pin_cfg);
7932 bnx2x_set_cfg_pin(bp, pin_cfg, gpio_mode);
7933 }
7934
7935 static void bnx2x_set_sfp_module_fault_led(struct link_params *params,
7936 u8 gpio_mode)
7937 {
7938 struct bnx2x *bp = params->bp;
7939 DP(NETIF_MSG_LINK, "Setting SFP+ module fault LED to %d\n", gpio_mode);
7940 if (CHIP_IS_E3(bp)) {
7941 /*
7942 * Low ==> if SFP+ module is supported otherwise
7943 * High ==> if SFP+ module is not on the approved vendor list
7944 */
7945 bnx2x_set_e3_module_fault_led(params, gpio_mode);
7946 } else
7947 bnx2x_set_e1e2_module_fault_led(params, gpio_mode);
7948 }
7949
7950 static void bnx2x_warpcore_power_module(struct link_params *params,
7951 struct bnx2x_phy *phy,
7952 u8 power)
7953 {
7954 u32 pin_cfg;
7955 struct bnx2x *bp = params->bp;
7956
7957 pin_cfg = (REG_RD(bp, params->shmem_base +
7958 offsetof(struct shmem_region,
7959 dev_info.port_hw_config[params->port].e3_sfp_ctrl)) &
7960 PORT_HW_CFG_E3_PWR_DIS_MASK) >>
7961 PORT_HW_CFG_E3_PWR_DIS_SHIFT;
7962
7963 if (pin_cfg == PIN_CFG_NA)
7964 return;
7965 DP(NETIF_MSG_LINK, "Setting SFP+ module power to %d using pin cfg %d\n",
7966 power, pin_cfg);
7967 /*
7968 * Low ==> corresponding SFP+ module is powered
7969 * high ==> the SFP+ module is powered down
7970 */
7971 bnx2x_set_cfg_pin(bp, pin_cfg, power ^ 1);
7972 }
7973
7974 static void bnx2x_warpcore_hw_reset(struct bnx2x_phy *phy,
7975 struct link_params *params)
7976 {
7977 bnx2x_warpcore_power_module(params, phy, 0);
7978 }
7979
7980 static void bnx2x_power_sfp_module(struct link_params *params,
7981 struct bnx2x_phy *phy,
7982 u8 power)
7983 {
7984 struct bnx2x *bp = params->bp;
7985 DP(NETIF_MSG_LINK, "Setting SFP+ power to %x\n", power);
7986
7987 switch (phy->type) {
7988 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
7989 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8722:
7990 bnx2x_8727_power_module(params->bp, phy, power);
7991 break;
7992 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT:
7993 bnx2x_warpcore_power_module(params, phy, power);
7994 break;
7995 default:
7996 break;
7997 }
7998 }
7999 static void bnx2x_warpcore_set_limiting_mode(struct link_params *params,
8000 struct bnx2x_phy *phy,
8001 u16 edc_mode)
8002 {
8003 u16 val = 0;
8004 u16 mode = MDIO_WC_REG_UC_INFO_B1_FIRMWARE_MODE_DEFAULT;
8005 struct bnx2x *bp = params->bp;
8006
8007 u8 lane = bnx2x_get_warpcore_lane(phy, params);
8008 /* This is a global register which controls all lanes */
8009 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
8010 MDIO_WC_REG_UC_INFO_B1_FIRMWARE_MODE, &val);
8011 val &= ~(0xf << (lane << 2));
8012
8013 switch (edc_mode) {
8014 case EDC_MODE_LINEAR:
8015 case EDC_MODE_LIMITING:
8016 mode = MDIO_WC_REG_UC_INFO_B1_FIRMWARE_MODE_DEFAULT;
8017 break;
8018 case EDC_MODE_PASSIVE_DAC:
8019 mode = MDIO_WC_REG_UC_INFO_B1_FIRMWARE_MODE_SFP_DAC;
8020 break;
8021 default:
8022 break;
8023 }
8024
8025 val |= (mode << (lane << 2));
8026 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
8027 MDIO_WC_REG_UC_INFO_B1_FIRMWARE_MODE, val);
8028 /* A must read */
8029 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
8030 MDIO_WC_REG_UC_INFO_B1_FIRMWARE_MODE, &val);
8031
8032 /* Restart microcode to re-read the new mode */
8033 bnx2x_warpcore_reset_lane(bp, phy, 1);
8034 bnx2x_warpcore_reset_lane(bp, phy, 0);
8035
8036 }
8037
8038 static void bnx2x_set_limiting_mode(struct link_params *params,
8039 struct bnx2x_phy *phy,
8040 u16 edc_mode)
8041 {
8042 switch (phy->type) {
8043 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726:
8044 bnx2x_8726_set_limiting_mode(params->bp, phy, edc_mode);
8045 break;
8046 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
8047 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8722:
8048 bnx2x_8727_set_limiting_mode(params->bp, phy, edc_mode);
8049 break;
8050 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT:
8051 bnx2x_warpcore_set_limiting_mode(params, phy, edc_mode);
8052 break;
8053 }
8054 }
8055
8056 int bnx2x_sfp_module_detection(struct bnx2x_phy *phy,
8057 struct link_params *params)
8058 {
8059 struct bnx2x *bp = params->bp;
8060 u16 edc_mode;
8061 int rc = 0;
8062
8063 u32 val = REG_RD(bp, params->shmem_base +
8064 offsetof(struct shmem_region, dev_info.
8065 port_feature_config[params->port].config));
8066
8067 DP(NETIF_MSG_LINK, "SFP+ module plugged in/out detected on port %d\n",
8068 params->port);
8069 /* Power up module */
8070 bnx2x_power_sfp_module(params, phy, 1);
8071 if (bnx2x_get_edc_mode(phy, params, &edc_mode) != 0) {
8072 DP(NETIF_MSG_LINK, "Failed to get valid module type\n");
8073 return -EINVAL;
8074 } else if (bnx2x_verify_sfp_module(phy, params) != 0) {
8075 /* check SFP+ module compatibility */
8076 DP(NETIF_MSG_LINK, "Module verification failed!!\n");
8077 rc = -EINVAL;
8078 /* Turn on fault module-detected led */
8079 bnx2x_set_sfp_module_fault_led(params,
8080 MISC_REGISTERS_GPIO_HIGH);
8081
8082 /* Check if need to power down the SFP+ module */
8083 if ((val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) ==
8084 PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_POWER_DOWN) {
8085 DP(NETIF_MSG_LINK, "Shutdown SFP+ module!!\n");
8086 bnx2x_power_sfp_module(params, phy, 0);
8087 return rc;
8088 }
8089 } else {
8090 /* Turn off fault module-detected led */
8091 bnx2x_set_sfp_module_fault_led(params, MISC_REGISTERS_GPIO_LOW);
8092 }
8093
8094 /*
8095 * Check and set limiting mode / LRM mode on 8726. On 8727 it
8096 * is done automatically
8097 */
8098 bnx2x_set_limiting_mode(params, phy, edc_mode);
8099
8100 /*
8101 * Enable transmit for this module if the module is approved, or
8102 * if unapproved modules should also enable the Tx laser
8103 */
8104 if (rc == 0 ||
8105 (val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) !=
8106 PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_DISABLE_TX_LASER)
8107 bnx2x_sfp_set_transmitter(params, phy, 1);
8108 else
8109 bnx2x_sfp_set_transmitter(params, phy, 0);
8110
8111 return rc;
8112 }
8113
8114 void bnx2x_handle_module_detect_int(struct link_params *params)
8115 {
8116 struct bnx2x *bp = params->bp;
8117 struct bnx2x_phy *phy;
8118 u32 gpio_val;
8119 u8 gpio_num, gpio_port;
8120 if (CHIP_IS_E3(bp))
8121 phy = &params->phy[INT_PHY];
8122 else
8123 phy = &params->phy[EXT_PHY1];
8124
8125 if (bnx2x_get_mod_abs_int_cfg(bp, params->chip_id, params->shmem_base,
8126 params->port, &gpio_num, &gpio_port) ==
8127 -EINVAL) {
8128 DP(NETIF_MSG_LINK, "Failed to get MOD_ABS interrupt config\n");
8129 return;
8130 }
8131
8132 /* Set valid module led off */
8133 bnx2x_set_sfp_module_fault_led(params, MISC_REGISTERS_GPIO_HIGH);
8134
8135 /* Get current gpio val reflecting module plugged in / out*/
8136 gpio_val = bnx2x_get_gpio(bp, gpio_num, gpio_port);
8137
8138 /* Call the handling function in case module is detected */
8139 if (gpio_val == 0) {
8140 bnx2x_power_sfp_module(params, phy, 1);
8141 bnx2x_set_gpio_int(bp, gpio_num,
8142 MISC_REGISTERS_GPIO_INT_OUTPUT_CLR,
8143 gpio_port);
8144 if (bnx2x_wait_for_sfp_module_initialized(phy, params) == 0)
8145 bnx2x_sfp_module_detection(phy, params);
8146 else
8147 DP(NETIF_MSG_LINK, "SFP+ module is not initialized\n");
8148 } else {
8149 u32 val = REG_RD(bp, params->shmem_base +
8150 offsetof(struct shmem_region, dev_info.
8151 port_feature_config[params->port].
8152 config));
8153 bnx2x_set_gpio_int(bp, gpio_num,
8154 MISC_REGISTERS_GPIO_INT_OUTPUT_SET,
8155 gpio_port);
8156 /*
8157 * Module was plugged out.
8158 * Disable transmit for this module
8159 */
8160 phy->media_type = ETH_PHY_NOT_PRESENT;
8161 if (((val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) ==
8162 PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_DISABLE_TX_LASER) ||
8163 CHIP_IS_E3(bp))
8164 bnx2x_sfp_set_transmitter(params, phy, 0);
8165 }
8166 }
8167
8168 /******************************************************************/
8169 /* Used by 8706 and 8727 */
8170 /******************************************************************/
8171 static void bnx2x_sfp_mask_fault(struct bnx2x *bp,
8172 struct bnx2x_phy *phy,
8173 u16 alarm_status_offset,
8174 u16 alarm_ctrl_offset)
8175 {
8176 u16 alarm_status, val;
8177 bnx2x_cl45_read(bp, phy,
8178 MDIO_PMA_DEVAD, alarm_status_offset,
8179 &alarm_status);
8180 bnx2x_cl45_read(bp, phy,
8181 MDIO_PMA_DEVAD, alarm_status_offset,
8182 &alarm_status);
8183 /* Mask or enable the fault event. */
8184 bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, alarm_ctrl_offset, &val);
8185 if (alarm_status & (1<<0))
8186 val &= ~(1<<0);
8187 else
8188 val |= (1<<0);
8189 bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, alarm_ctrl_offset, val);
8190 }
8191 /******************************************************************/
8192 /* common BCM8706/BCM8726 PHY SECTION */
8193 /******************************************************************/
8194 static u8 bnx2x_8706_8726_read_status(struct bnx2x_phy *phy,
8195 struct link_params *params,
8196 struct link_vars *vars)
8197 {
8198 u8 link_up = 0;
8199 u16 val1, val2, rx_sd, pcs_status;
8200 struct bnx2x *bp = params->bp;
8201 DP(NETIF_MSG_LINK, "XGXS 8706/8726\n");
8202 /* Clear RX Alarm*/
8203 bnx2x_cl45_read(bp, phy,
8204 MDIO_PMA_DEVAD, MDIO_PMA_LASI_RXSTAT, &val2);
8205
8206 bnx2x_sfp_mask_fault(bp, phy, MDIO_PMA_LASI_TXSTAT,
8207 MDIO_PMA_LASI_TXCTRL);
8208
8209 /* clear LASI indication*/
8210 bnx2x_cl45_read(bp, phy,
8211 MDIO_PMA_DEVAD, MDIO_PMA_LASI_STAT, &val1);
8212 bnx2x_cl45_read(bp, phy,
8213 MDIO_PMA_DEVAD, MDIO_PMA_LASI_STAT, &val2);
8214 DP(NETIF_MSG_LINK, "8706/8726 LASI status 0x%x--> 0x%x\n", val1, val2);
8215
8216 bnx2x_cl45_read(bp, phy,
8217 MDIO_PMA_DEVAD, MDIO_PMA_REG_RX_SD, &rx_sd);
8218 bnx2x_cl45_read(bp, phy,
8219 MDIO_PCS_DEVAD, MDIO_PCS_REG_STATUS, &pcs_status);
8220 bnx2x_cl45_read(bp, phy,
8221 MDIO_AN_DEVAD, MDIO_AN_REG_LINK_STATUS, &val2);
8222 bnx2x_cl45_read(bp, phy,
8223 MDIO_AN_DEVAD, MDIO_AN_REG_LINK_STATUS, &val2);
8224
8225 DP(NETIF_MSG_LINK, "8706/8726 rx_sd 0x%x pcs_status 0x%x 1Gbps"
8226 " link_status 0x%x\n", rx_sd, pcs_status, val2);
8227 /*
8228 * link is up if both bit 0 of pmd_rx_sd and bit 0 of pcs_status
8229 * are set, or if the autoneg bit 1 is set
8230 */
8231 link_up = ((rx_sd & pcs_status & 0x1) || (val2 & (1<<1)));
8232 if (link_up) {
8233 if (val2 & (1<<1))
8234 vars->line_speed = SPEED_1000;
8235 else
8236 vars->line_speed = SPEED_10000;
8237 bnx2x_ext_phy_resolve_fc(phy, params, vars);
8238 vars->duplex = DUPLEX_FULL;
8239 }
8240
8241 /* Capture 10G link fault. Read twice to clear stale value. */
8242 if (vars->line_speed == SPEED_10000) {
8243 bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD,
8244 MDIO_PMA_LASI_TXSTAT, &val1);
8245 bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD,
8246 MDIO_PMA_LASI_TXSTAT, &val1);
8247 if (val1 & (1<<0))
8248 vars->fault_detected = 1;
8249 }
8250
8251 return link_up;
8252 }
8253
8254 /******************************************************************/
8255 /* BCM8706 PHY SECTION */
8256 /******************************************************************/
8257 static u8 bnx2x_8706_config_init(struct bnx2x_phy *phy,
8258 struct link_params *params,
8259 struct link_vars *vars)
8260 {
8261 u32 tx_en_mode;
8262 u16 cnt, val, tmp1;
8263 struct bnx2x *bp = params->bp;
8264
8265 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
8266 MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port);
8267 /* HW reset */
8268 bnx2x_ext_phy_hw_reset(bp, params->port);
8269 bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0xa040);
8270 bnx2x_wait_reset_complete(bp, phy, params);
8271
8272 /* Wait until fw is loaded */
8273 for (cnt = 0; cnt < 100; cnt++) {
8274 bnx2x_cl45_read(bp, phy,
8275 MDIO_PMA_DEVAD, MDIO_PMA_REG_ROM_VER1, &val);
8276 if (val)
8277 break;
8278 msleep(10);
8279 }
8280 DP(NETIF_MSG_LINK, "XGXS 8706 is initialized after %d ms\n", cnt);
8281 if ((params->feature_config_flags &
8282 FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED)) {
8283 u8 i;
8284 u16 reg;
8285 for (i = 0; i < 4; i++) {
8286 reg = MDIO_XS_8706_REG_BANK_RX0 +
8287 i*(MDIO_XS_8706_REG_BANK_RX1 -
8288 MDIO_XS_8706_REG_BANK_RX0);
8289 bnx2x_cl45_read(bp, phy, MDIO_XS_DEVAD, reg, &val);
8290 /* Clear first 3 bits of the control */
8291 val &= ~0x7;
8292 /* Set control bits according to configuration */
8293 val |= (phy->rx_preemphasis[i] & 0x7);
8294 DP(NETIF_MSG_LINK, "Setting RX Equalizer to BCM8706"
8295 " reg 0x%x <-- val 0x%x\n", reg, val);
8296 bnx2x_cl45_write(bp, phy, MDIO_XS_DEVAD, reg, val);
8297 }
8298 }
8299 /* Force speed */
8300 if (phy->req_line_speed == SPEED_10000) {
8301 DP(NETIF_MSG_LINK, "XGXS 8706 force 10Gbps\n");
8302
8303 bnx2x_cl45_write(bp, phy,
8304 MDIO_PMA_DEVAD,
8305 MDIO_PMA_REG_DIGITAL_CTRL, 0x400);
8306 bnx2x_cl45_write(bp, phy,
8307 MDIO_PMA_DEVAD, MDIO_PMA_LASI_TXCTRL,
8308 0);
8309 /* Arm LASI for link and Tx fault. */
8310 bnx2x_cl45_write(bp, phy,
8311 MDIO_PMA_DEVAD, MDIO_PMA_LASI_CTRL, 3);
8312 } else {
8313 /* Force 1Gbps using autoneg with 1G advertisement */
8314
8315 /* Allow CL37 through CL73 */
8316 DP(NETIF_MSG_LINK, "XGXS 8706 AutoNeg\n");
8317 bnx2x_cl45_write(bp, phy,
8318 MDIO_AN_DEVAD, MDIO_AN_REG_CL37_CL73, 0x040c);
8319
8320 /* Enable Full-Duplex advertisement on CL37 */
8321 bnx2x_cl45_write(bp, phy,
8322 MDIO_AN_DEVAD, MDIO_AN_REG_CL37_FC_LP, 0x0020);
8323 /* Enable CL37 AN */
8324 bnx2x_cl45_write(bp, phy,
8325 MDIO_AN_DEVAD, MDIO_AN_REG_CL37_AN, 0x1000);
8326 /* 1G support */
8327 bnx2x_cl45_write(bp, phy,
8328 MDIO_AN_DEVAD, MDIO_AN_REG_ADV, (1<<5));
8329
8330 /* Enable clause 73 AN */
8331 bnx2x_cl45_write(bp, phy,
8332 MDIO_AN_DEVAD, MDIO_AN_REG_CTRL, 0x1200);
8333 bnx2x_cl45_write(bp, phy,
8334 MDIO_PMA_DEVAD, MDIO_PMA_LASI_RXCTRL,
8335 0x0400);
8336 bnx2x_cl45_write(bp, phy,
8337 MDIO_PMA_DEVAD, MDIO_PMA_LASI_CTRL,
8338 0x0004);
8339 }
8340 bnx2x_save_bcm_spirom_ver(bp, phy, params->port);
8341
8342 /*
8343 * If TX Laser is controlled by GPIO_0, do not let PHY go into low
8344 * power mode, if TX Laser is disabled
8345 */
8346
8347 tx_en_mode = REG_RD(bp, params->shmem_base +
8348 offsetof(struct shmem_region,
8349 dev_info.port_hw_config[params->port].sfp_ctrl))
8350 & PORT_HW_CFG_TX_LASER_MASK;
8351
8352 if (tx_en_mode == PORT_HW_CFG_TX_LASER_GPIO0) {
8353 DP(NETIF_MSG_LINK, "Enabling TXONOFF_PWRDN_DIS\n");
8354 bnx2x_cl45_read(bp, phy,
8355 MDIO_PMA_DEVAD, MDIO_PMA_REG_DIGITAL_CTRL, &tmp1);
8356 tmp1 |= 0x1;
8357 bnx2x_cl45_write(bp, phy,
8358 MDIO_PMA_DEVAD, MDIO_PMA_REG_DIGITAL_CTRL, tmp1);
8359 }
8360
8361 return 0;
8362 }
8363
8364 static int bnx2x_8706_read_status(struct bnx2x_phy *phy,
8365 struct link_params *params,
8366 struct link_vars *vars)
8367 {
8368 return bnx2x_8706_8726_read_status(phy, params, vars);
8369 }
8370
8371 /******************************************************************/
8372 /* BCM8726 PHY SECTION */
8373 /******************************************************************/
8374 static void bnx2x_8726_config_loopback(struct bnx2x_phy *phy,
8375 struct link_params *params)
8376 {
8377 struct bnx2x *bp = params->bp;
8378 DP(NETIF_MSG_LINK, "PMA/PMD ext_phy_loopback: 8726\n");
8379 bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0x0001);
8380 }
8381
8382 static void bnx2x_8726_external_rom_boot(struct bnx2x_phy *phy,
8383 struct link_params *params)
8384 {
8385 struct bnx2x *bp = params->bp;
8386 /* Need to wait 100ms after reset */
8387 msleep(100);
8388
8389 /* Micro controller re-boot */
8390 bnx2x_cl45_write(bp, phy,
8391 MDIO_PMA_DEVAD, MDIO_PMA_REG_GEN_CTRL, 0x018B);
8392
8393 /* Set soft reset */
8394 bnx2x_cl45_write(bp, phy,
8395 MDIO_PMA_DEVAD,
8396 MDIO_PMA_REG_GEN_CTRL,
8397 MDIO_PMA_REG_GEN_CTRL_ROM_MICRO_RESET);
8398
8399 bnx2x_cl45_write(bp, phy,
8400 MDIO_PMA_DEVAD,
8401 MDIO_PMA_REG_MISC_CTRL1, 0x0001);
8402
8403 bnx2x_cl45_write(bp, phy,
8404 MDIO_PMA_DEVAD,
8405 MDIO_PMA_REG_GEN_CTRL,
8406 MDIO_PMA_REG_GEN_CTRL_ROM_RESET_INTERNAL_MP);
8407
8408 /* wait for 150ms for microcode load */
8409 msleep(150);
8410
8411 /* Disable serial boot control, tristates pins SS_N, SCK, MOSI, MISO */
8412 bnx2x_cl45_write(bp, phy,
8413 MDIO_PMA_DEVAD,
8414 MDIO_PMA_REG_MISC_CTRL1, 0x0000);
8415
8416 msleep(200);
8417 bnx2x_save_bcm_spirom_ver(bp, phy, params->port);
8418 }
8419
8420 static u8 bnx2x_8726_read_status(struct bnx2x_phy *phy,
8421 struct link_params *params,
8422 struct link_vars *vars)
8423 {
8424 struct bnx2x *bp = params->bp;
8425 u16 val1;
8426 u8 link_up = bnx2x_8706_8726_read_status(phy, params, vars);
8427 if (link_up) {
8428 bnx2x_cl45_read(bp, phy,
8429 MDIO_PMA_DEVAD, MDIO_PMA_REG_PHY_IDENTIFIER,
8430 &val1);
8431 if (val1 & (1<<15)) {
8432 DP(NETIF_MSG_LINK, "Tx is disabled\n");
8433 link_up = 0;
8434 vars->line_speed = 0;
8435 }
8436 }
8437 return link_up;
8438 }
8439
8440
8441 static int bnx2x_8726_config_init(struct bnx2x_phy *phy,
8442 struct link_params *params,
8443 struct link_vars *vars)
8444 {
8445 struct bnx2x *bp = params->bp;
8446 DP(NETIF_MSG_LINK, "Initializing BCM8726\n");
8447
8448 bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 1<<15);
8449 bnx2x_wait_reset_complete(bp, phy, params);
8450
8451 bnx2x_8726_external_rom_boot(phy, params);
8452
8453 /*
8454 * Need to call module detected on initialization since the module
8455 * detection triggered by actual module insertion might occur before
8456 * driver is loaded, and when driver is loaded, it reset all
8457 * registers, including the transmitter
8458 */
8459 bnx2x_sfp_module_detection(phy, params);
8460
8461 if (phy->req_line_speed == SPEED_1000) {
8462 DP(NETIF_MSG_LINK, "Setting 1G force\n");
8463 bnx2x_cl45_write(bp, phy,
8464 MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0x40);
8465 bnx2x_cl45_write(bp, phy,
8466 MDIO_PMA_DEVAD, MDIO_PMA_REG_10G_CTRL2, 0xD);
8467 bnx2x_cl45_write(bp, phy,
8468 MDIO_PMA_DEVAD, MDIO_PMA_LASI_CTRL, 0x5);
8469 bnx2x_cl45_write(bp, phy,
8470 MDIO_PMA_DEVAD, MDIO_PMA_LASI_RXCTRL,
8471 0x400);
8472 } else if ((phy->req_line_speed == SPEED_AUTO_NEG) &&
8473 (phy->speed_cap_mask &
8474 PORT_HW_CFG_SPEED_CAPABILITY_D0_1G) &&
8475 ((phy->speed_cap_mask &
8476 PORT_HW_CFG_SPEED_CAPABILITY_D0_10G) !=
8477 PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)) {
8478 DP(NETIF_MSG_LINK, "Setting 1G clause37\n");
8479 /* Set Flow control */
8480 bnx2x_ext_phy_set_pause(params, phy, vars);
8481 bnx2x_cl45_write(bp, phy,
8482 MDIO_AN_DEVAD, MDIO_AN_REG_ADV, 0x20);
8483 bnx2x_cl45_write(bp, phy,
8484 MDIO_AN_DEVAD, MDIO_AN_REG_CL37_CL73, 0x040c);
8485 bnx2x_cl45_write(bp, phy,
8486 MDIO_AN_DEVAD, MDIO_AN_REG_CL37_FC_LD, 0x0020);
8487 bnx2x_cl45_write(bp, phy,
8488 MDIO_AN_DEVAD, MDIO_AN_REG_CL37_AN, 0x1000);
8489 bnx2x_cl45_write(bp, phy,
8490 MDIO_AN_DEVAD, MDIO_AN_REG_CTRL, 0x1200);
8491 /*
8492 * Enable RX-ALARM control to receive interrupt for 1G speed
8493 * change
8494 */
8495 bnx2x_cl45_write(bp, phy,
8496 MDIO_PMA_DEVAD, MDIO_PMA_LASI_CTRL, 0x4);
8497 bnx2x_cl45_write(bp, phy,
8498 MDIO_PMA_DEVAD, MDIO_PMA_LASI_RXCTRL,
8499 0x400);
8500
8501 } else { /* Default 10G. Set only LASI control */
8502 bnx2x_cl45_write(bp, phy,
8503 MDIO_PMA_DEVAD, MDIO_PMA_LASI_CTRL, 1);
8504 }
8505
8506 /* Set TX PreEmphasis if needed */
8507 if ((params->feature_config_flags &
8508 FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED)) {
8509 DP(NETIF_MSG_LINK, "Setting TX_CTRL1 0x%x,"
8510 "TX_CTRL2 0x%x\n",
8511 phy->tx_preemphasis[0],
8512 phy->tx_preemphasis[1]);
8513 bnx2x_cl45_write(bp, phy,
8514 MDIO_PMA_DEVAD,
8515 MDIO_PMA_REG_8726_TX_CTRL1,
8516 phy->tx_preemphasis[0]);
8517
8518 bnx2x_cl45_write(bp, phy,
8519 MDIO_PMA_DEVAD,
8520 MDIO_PMA_REG_8726_TX_CTRL2,
8521 phy->tx_preemphasis[1]);
8522 }
8523
8524 return 0;
8525
8526 }
8527
8528 static void bnx2x_8726_link_reset(struct bnx2x_phy *phy,
8529 struct link_params *params)
8530 {
8531 struct bnx2x *bp = params->bp;
8532 DP(NETIF_MSG_LINK, "bnx2x_8726_link_reset port %d\n", params->port);
8533 /* Set serial boot control for external load */
8534 bnx2x_cl45_write(bp, phy,
8535 MDIO_PMA_DEVAD,
8536 MDIO_PMA_REG_GEN_CTRL, 0x0001);
8537 }
8538
8539 /******************************************************************/
8540 /* BCM8727 PHY SECTION */
8541 /******************************************************************/
8542
8543 static void bnx2x_8727_set_link_led(struct bnx2x_phy *phy,
8544 struct link_params *params, u8 mode)
8545 {
8546 struct bnx2x *bp = params->bp;
8547 u16 led_mode_bitmask = 0;
8548 u16 gpio_pins_bitmask = 0;
8549 u16 val;
8550 /* Only NOC flavor requires to set the LED specifically */
8551 if (!(phy->flags & FLAGS_NOC))
8552 return;
8553 switch (mode) {
8554 case LED_MODE_FRONT_PANEL_OFF:
8555 case LED_MODE_OFF:
8556 led_mode_bitmask = 0;
8557 gpio_pins_bitmask = 0x03;
8558 break;
8559 case LED_MODE_ON:
8560 led_mode_bitmask = 0;
8561 gpio_pins_bitmask = 0x02;
8562 break;
8563 case LED_MODE_OPER:
8564 led_mode_bitmask = 0x60;
8565 gpio_pins_bitmask = 0x11;
8566 break;
8567 }
8568 bnx2x_cl45_read(bp, phy,
8569 MDIO_PMA_DEVAD,
8570 MDIO_PMA_REG_8727_PCS_OPT_CTRL,
8571 &val);
8572 val &= 0xff8f;
8573 val |= led_mode_bitmask;
8574 bnx2x_cl45_write(bp, phy,
8575 MDIO_PMA_DEVAD,
8576 MDIO_PMA_REG_8727_PCS_OPT_CTRL,
8577 val);
8578 bnx2x_cl45_read(bp, phy,
8579 MDIO_PMA_DEVAD,
8580 MDIO_PMA_REG_8727_GPIO_CTRL,
8581 &val);
8582 val &= 0xffe0;
8583 val |= gpio_pins_bitmask;
8584 bnx2x_cl45_write(bp, phy,
8585 MDIO_PMA_DEVAD,
8586 MDIO_PMA_REG_8727_GPIO_CTRL,
8587 val);
8588 }
8589 static void bnx2x_8727_hw_reset(struct bnx2x_phy *phy,
8590 struct link_params *params) {
8591 u32 swap_val, swap_override;
8592 u8 port;
8593 /*
8594 * The PHY reset is controlled by GPIO 1. Fake the port number
8595 * to cancel the swap done in set_gpio()
8596 */
8597 struct bnx2x *bp = params->bp;
8598 swap_val = REG_RD(bp, NIG_REG_PORT_SWAP);
8599 swap_override = REG_RD(bp, NIG_REG_STRAP_OVERRIDE);
8600 port = (swap_val && swap_override) ^ 1;
8601 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
8602 MISC_REGISTERS_GPIO_OUTPUT_LOW, port);
8603 }
8604
8605 static int bnx2x_8727_config_init(struct bnx2x_phy *phy,
8606 struct link_params *params,
8607 struct link_vars *vars)
8608 {
8609 u32 tx_en_mode;
8610 u16 tmp1, val, mod_abs, tmp2;
8611 u16 rx_alarm_ctrl_val;
8612 u16 lasi_ctrl_val;
8613 struct bnx2x *bp = params->bp;
8614 /* Enable PMD link, MOD_ABS_FLT, and 1G link alarm */
8615
8616 bnx2x_wait_reset_complete(bp, phy, params);
8617 rx_alarm_ctrl_val = (1<<2) | (1<<5) ;
8618 /* Should be 0x6 to enable XS on Tx side. */
8619 lasi_ctrl_val = 0x0006;
8620
8621 DP(NETIF_MSG_LINK, "Initializing BCM8727\n");
8622 /* enable LASI */
8623 bnx2x_cl45_write(bp, phy,
8624 MDIO_PMA_DEVAD, MDIO_PMA_LASI_RXCTRL,
8625 rx_alarm_ctrl_val);
8626 bnx2x_cl45_write(bp, phy,
8627 MDIO_PMA_DEVAD, MDIO_PMA_LASI_TXCTRL,
8628 0);
8629 bnx2x_cl45_write(bp, phy,
8630 MDIO_PMA_DEVAD, MDIO_PMA_LASI_CTRL, lasi_ctrl_val);
8631
8632 /*
8633 * Initially configure MOD_ABS to interrupt when module is
8634 * presence( bit 8)
8635 */
8636 bnx2x_cl45_read(bp, phy,
8637 MDIO_PMA_DEVAD, MDIO_PMA_REG_PHY_IDENTIFIER, &mod_abs);
8638 /*
8639 * Set EDC off by setting OPTXLOS signal input to low (bit 9).
8640 * When the EDC is off it locks onto a reference clock and avoids
8641 * becoming 'lost'
8642 */
8643 mod_abs &= ~(1<<8);
8644 if (!(phy->flags & FLAGS_NOC))
8645 mod_abs &= ~(1<<9);
8646 bnx2x_cl45_write(bp, phy,
8647 MDIO_PMA_DEVAD, MDIO_PMA_REG_PHY_IDENTIFIER, mod_abs);
8648
8649
8650 /* Enable/Disable PHY transmitter output */
8651 bnx2x_set_disable_pmd_transmit(params, phy, 0);
8652
8653 /* Make MOD_ABS give interrupt on change */
8654 bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_8727_PCS_OPT_CTRL,
8655 &val);
8656 val |= (1<<12);
8657 if (phy->flags & FLAGS_NOC)
8658 val |= (3<<5);
8659
8660 /*
8661 * Set 8727 GPIOs to input to allow reading from the 8727 GPIO0
8662 * status which reflect SFP+ module over-current
8663 */
8664 if (!(phy->flags & FLAGS_NOC))
8665 val &= 0xff8f; /* Reset bits 4-6 */
8666 bnx2x_cl45_write(bp, phy,
8667 MDIO_PMA_DEVAD, MDIO_PMA_REG_8727_PCS_OPT_CTRL, val);
8668
8669 bnx2x_8727_power_module(bp, phy, 1);
8670
8671 bnx2x_cl45_read(bp, phy,
8672 MDIO_PMA_DEVAD, MDIO_PMA_REG_M8051_MSGOUT_REG, &tmp1);
8673
8674 bnx2x_cl45_read(bp, phy,
8675 MDIO_PMA_DEVAD, MDIO_PMA_LASI_RXSTAT, &tmp1);
8676
8677 /* Set option 1G speed */
8678 if (phy->req_line_speed == SPEED_1000) {
8679 DP(NETIF_MSG_LINK, "Setting 1G force\n");
8680 bnx2x_cl45_write(bp, phy,
8681 MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0x40);
8682 bnx2x_cl45_write(bp, phy,
8683 MDIO_PMA_DEVAD, MDIO_PMA_REG_10G_CTRL2, 0xD);
8684 bnx2x_cl45_read(bp, phy,
8685 MDIO_PMA_DEVAD, MDIO_PMA_REG_10G_CTRL2, &tmp1);
8686 DP(NETIF_MSG_LINK, "1.7 = 0x%x\n", tmp1);
8687 /*
8688 * Power down the XAUI until link is up in case of dual-media
8689 * and 1G
8690 */
8691 if (DUAL_MEDIA(params)) {
8692 bnx2x_cl45_read(bp, phy,
8693 MDIO_PMA_DEVAD,
8694 MDIO_PMA_REG_8727_PCS_GP, &val);
8695 val |= (3<<10);
8696 bnx2x_cl45_write(bp, phy,
8697 MDIO_PMA_DEVAD,
8698 MDIO_PMA_REG_8727_PCS_GP, val);
8699 }
8700 } else if ((phy->req_line_speed == SPEED_AUTO_NEG) &&
8701 ((phy->speed_cap_mask &
8702 PORT_HW_CFG_SPEED_CAPABILITY_D0_1G)) &&
8703 ((phy->speed_cap_mask &
8704 PORT_HW_CFG_SPEED_CAPABILITY_D0_10G) !=
8705 PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)) {
8706
8707 DP(NETIF_MSG_LINK, "Setting 1G clause37\n");
8708 bnx2x_cl45_write(bp, phy,
8709 MDIO_AN_DEVAD, MDIO_AN_REG_8727_MISC_CTRL, 0);
8710 bnx2x_cl45_write(bp, phy,
8711 MDIO_AN_DEVAD, MDIO_AN_REG_CL37_AN, 0x1300);
8712 } else {
8713 /*
8714 * Since the 8727 has only single reset pin, need to set the 10G
8715 * registers although it is default
8716 */
8717 bnx2x_cl45_write(bp, phy,
8718 MDIO_AN_DEVAD, MDIO_AN_REG_8727_MISC_CTRL,
8719 0x0020);
8720 bnx2x_cl45_write(bp, phy,
8721 MDIO_AN_DEVAD, MDIO_AN_REG_CL37_AN, 0x0100);
8722 bnx2x_cl45_write(bp, phy,
8723 MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0x2040);
8724 bnx2x_cl45_write(bp, phy,
8725 MDIO_PMA_DEVAD, MDIO_PMA_REG_10G_CTRL2,
8726 0x0008);
8727 }
8728
8729 /*
8730 * Set 2-wire transfer rate of SFP+ module EEPROM
8731 * to 100Khz since some DACs(direct attached cables) do
8732 * not work at 400Khz.
8733 */
8734 bnx2x_cl45_write(bp, phy,
8735 MDIO_PMA_DEVAD, MDIO_PMA_REG_8727_TWO_WIRE_SLAVE_ADDR,
8736 0xa001);
8737
8738 /* Set TX PreEmphasis if needed */
8739 if ((params->feature_config_flags &
8740 FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED)) {
8741 DP(NETIF_MSG_LINK, "Setting TX_CTRL1 0x%x, TX_CTRL2 0x%x\n",
8742 phy->tx_preemphasis[0],
8743 phy->tx_preemphasis[1]);
8744 bnx2x_cl45_write(bp, phy,
8745 MDIO_PMA_DEVAD, MDIO_PMA_REG_8727_TX_CTRL1,
8746 phy->tx_preemphasis[0]);
8747
8748 bnx2x_cl45_write(bp, phy,
8749 MDIO_PMA_DEVAD, MDIO_PMA_REG_8727_TX_CTRL2,
8750 phy->tx_preemphasis[1]);
8751 }
8752
8753 /*
8754 * If TX Laser is controlled by GPIO_0, do not let PHY go into low
8755 * power mode, if TX Laser is disabled
8756 */
8757 tx_en_mode = REG_RD(bp, params->shmem_base +
8758 offsetof(struct shmem_region,
8759 dev_info.port_hw_config[params->port].sfp_ctrl))
8760 & PORT_HW_CFG_TX_LASER_MASK;
8761
8762 if (tx_en_mode == PORT_HW_CFG_TX_LASER_GPIO0) {
8763
8764 DP(NETIF_MSG_LINK, "Enabling TXONOFF_PWRDN_DIS\n");
8765 bnx2x_cl45_read(bp, phy,
8766 MDIO_PMA_DEVAD, MDIO_PMA_REG_8727_OPT_CFG_REG, &tmp2);
8767 tmp2 |= 0x1000;
8768 tmp2 &= 0xFFEF;
8769 bnx2x_cl45_write(bp, phy,
8770 MDIO_PMA_DEVAD, MDIO_PMA_REG_8727_OPT_CFG_REG, tmp2);
8771 }
8772
8773 return 0;
8774 }
8775
8776 static void bnx2x_8727_handle_mod_abs(struct bnx2x_phy *phy,
8777 struct link_params *params)
8778 {
8779 struct bnx2x *bp = params->bp;
8780 u16 mod_abs, rx_alarm_status;
8781 u32 val = REG_RD(bp, params->shmem_base +
8782 offsetof(struct shmem_region, dev_info.
8783 port_feature_config[params->port].
8784 config));
8785 bnx2x_cl45_read(bp, phy,
8786 MDIO_PMA_DEVAD,
8787 MDIO_PMA_REG_PHY_IDENTIFIER, &mod_abs);
8788 if (mod_abs & (1<<8)) {
8789
8790 /* Module is absent */
8791 DP(NETIF_MSG_LINK, "MOD_ABS indication "
8792 "show module is absent\n");
8793 phy->media_type = ETH_PHY_NOT_PRESENT;
8794 /*
8795 * 1. Set mod_abs to detect next module
8796 * presence event
8797 * 2. Set EDC off by setting OPTXLOS signal input to low
8798 * (bit 9).
8799 * When the EDC is off it locks onto a reference clock and
8800 * avoids becoming 'lost'.
8801 */
8802 mod_abs &= ~(1<<8);
8803 if (!(phy->flags & FLAGS_NOC))
8804 mod_abs &= ~(1<<9);
8805 bnx2x_cl45_write(bp, phy,
8806 MDIO_PMA_DEVAD,
8807 MDIO_PMA_REG_PHY_IDENTIFIER, mod_abs);
8808
8809 /*
8810 * Clear RX alarm since it stays up as long as
8811 * the mod_abs wasn't changed
8812 */
8813 bnx2x_cl45_read(bp, phy,
8814 MDIO_PMA_DEVAD,
8815 MDIO_PMA_LASI_RXSTAT, &rx_alarm_status);
8816
8817 } else {
8818 /* Module is present */
8819 DP(NETIF_MSG_LINK, "MOD_ABS indication "
8820 "show module is present\n");
8821 /*
8822 * First disable transmitter, and if the module is ok, the
8823 * module_detection will enable it
8824 * 1. Set mod_abs to detect next module absent event ( bit 8)
8825 * 2. Restore the default polarity of the OPRXLOS signal and
8826 * this signal will then correctly indicate the presence or
8827 * absence of the Rx signal. (bit 9)
8828 */
8829 mod_abs |= (1<<8);
8830 if (!(phy->flags & FLAGS_NOC))
8831 mod_abs |= (1<<9);
8832 bnx2x_cl45_write(bp, phy,
8833 MDIO_PMA_DEVAD,
8834 MDIO_PMA_REG_PHY_IDENTIFIER, mod_abs);
8835
8836 /*
8837 * Clear RX alarm since it stays up as long as the mod_abs
8838 * wasn't changed. This is need to be done before calling the
8839 * module detection, otherwise it will clear* the link update
8840 * alarm
8841 */
8842 bnx2x_cl45_read(bp, phy,
8843 MDIO_PMA_DEVAD,
8844 MDIO_PMA_LASI_RXSTAT, &rx_alarm_status);
8845
8846
8847 if ((val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) ==
8848 PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_DISABLE_TX_LASER)
8849 bnx2x_sfp_set_transmitter(params, phy, 0);
8850
8851 if (bnx2x_wait_for_sfp_module_initialized(phy, params) == 0)
8852 bnx2x_sfp_module_detection(phy, params);
8853 else
8854 DP(NETIF_MSG_LINK, "SFP+ module is not initialized\n");
8855 }
8856
8857 DP(NETIF_MSG_LINK, "8727 RX_ALARM_STATUS 0x%x\n",
8858 rx_alarm_status);
8859 /* No need to check link status in case of module plugged in/out */
8860 }
8861
8862 static u8 bnx2x_8727_read_status(struct bnx2x_phy *phy,
8863 struct link_params *params,
8864 struct link_vars *vars)
8865
8866 {
8867 struct bnx2x *bp = params->bp;
8868 u8 link_up = 0, oc_port = params->port;
8869 u16 link_status = 0;
8870 u16 rx_alarm_status, lasi_ctrl, val1;
8871
8872 /* If PHY is not initialized, do not check link status */
8873 bnx2x_cl45_read(bp, phy,
8874 MDIO_PMA_DEVAD, MDIO_PMA_LASI_CTRL,
8875 &lasi_ctrl);
8876 if (!lasi_ctrl)
8877 return 0;
8878
8879 /* Check the LASI on Rx */
8880 bnx2x_cl45_read(bp, phy,
8881 MDIO_PMA_DEVAD, MDIO_PMA_LASI_RXSTAT,
8882 &rx_alarm_status);
8883 vars->line_speed = 0;
8884 DP(NETIF_MSG_LINK, "8727 RX_ALARM_STATUS 0x%x\n", rx_alarm_status);
8885
8886 bnx2x_sfp_mask_fault(bp, phy, MDIO_PMA_LASI_TXSTAT,
8887 MDIO_PMA_LASI_TXCTRL);
8888
8889 bnx2x_cl45_read(bp, phy,
8890 MDIO_PMA_DEVAD, MDIO_PMA_LASI_STAT, &val1);
8891
8892 DP(NETIF_MSG_LINK, "8727 LASI status 0x%x\n", val1);
8893
8894 /* Clear MSG-OUT */
8895 bnx2x_cl45_read(bp, phy,
8896 MDIO_PMA_DEVAD, MDIO_PMA_REG_M8051_MSGOUT_REG, &val1);
8897
8898 /*
8899 * If a module is present and there is need to check
8900 * for over current
8901 */
8902 if (!(phy->flags & FLAGS_NOC) && !(rx_alarm_status & (1<<5))) {
8903 /* Check over-current using 8727 GPIO0 input*/
8904 bnx2x_cl45_read(bp, phy,
8905 MDIO_PMA_DEVAD, MDIO_PMA_REG_8727_GPIO_CTRL,
8906 &val1);
8907
8908 if ((val1 & (1<<8)) == 0) {
8909 if (!CHIP_IS_E1x(bp))
8910 oc_port = BP_PATH(bp) + (params->port << 1);
8911 DP(NETIF_MSG_LINK, "8727 Power fault has been detected"
8912 " on port %d\n", oc_port);
8913 netdev_err(bp->dev, "Error: Power fault on Port %d has"
8914 " been detected and the power to "
8915 "that SFP+ module has been removed"
8916 " to prevent failure of the card."
8917 " Please remove the SFP+ module and"
8918 " restart the system to clear this"
8919 " error.\n",
8920 oc_port);
8921 /* Disable all RX_ALARMs except for mod_abs */
8922 bnx2x_cl45_write(bp, phy,
8923 MDIO_PMA_DEVAD,
8924 MDIO_PMA_LASI_RXCTRL, (1<<5));
8925
8926 bnx2x_cl45_read(bp, phy,
8927 MDIO_PMA_DEVAD,
8928 MDIO_PMA_REG_PHY_IDENTIFIER, &val1);
8929 /* Wait for module_absent_event */
8930 val1 |= (1<<8);
8931 bnx2x_cl45_write(bp, phy,
8932 MDIO_PMA_DEVAD,
8933 MDIO_PMA_REG_PHY_IDENTIFIER, val1);
8934 /* Clear RX alarm */
8935 bnx2x_cl45_read(bp, phy,
8936 MDIO_PMA_DEVAD,
8937 MDIO_PMA_LASI_RXSTAT, &rx_alarm_status);
8938 return 0;
8939 }
8940 } /* Over current check */
8941
8942 /* When module absent bit is set, check module */
8943 if (rx_alarm_status & (1<<5)) {
8944 bnx2x_8727_handle_mod_abs(phy, params);
8945 /* Enable all mod_abs and link detection bits */
8946 bnx2x_cl45_write(bp, phy,
8947 MDIO_PMA_DEVAD, MDIO_PMA_LASI_RXCTRL,
8948 ((1<<5) | (1<<2)));
8949 }
8950 DP(NETIF_MSG_LINK, "Enabling 8727 TX laser if SFP is approved\n");
8951 bnx2x_8727_specific_func(phy, params, ENABLE_TX);
8952 /* If transmitter is disabled, ignore false link up indication */
8953 bnx2x_cl45_read(bp, phy,
8954 MDIO_PMA_DEVAD, MDIO_PMA_REG_PHY_IDENTIFIER, &val1);
8955 if (val1 & (1<<15)) {
8956 DP(NETIF_MSG_LINK, "Tx is disabled\n");
8957 return 0;
8958 }
8959
8960 bnx2x_cl45_read(bp, phy,
8961 MDIO_PMA_DEVAD,
8962 MDIO_PMA_REG_8073_SPEED_LINK_STATUS, &link_status);
8963
8964 /*
8965 * Bits 0..2 --> speed detected,
8966 * Bits 13..15--> link is down
8967 */
8968 if ((link_status & (1<<2)) && (!(link_status & (1<<15)))) {
8969 link_up = 1;
8970 vars->line_speed = SPEED_10000;
8971 DP(NETIF_MSG_LINK, "port %x: External link up in 10G\n",
8972 params->port);
8973 } else if ((link_status & (1<<0)) && (!(link_status & (1<<13)))) {
8974 link_up = 1;
8975 vars->line_speed = SPEED_1000;
8976 DP(NETIF_MSG_LINK, "port %x: External link up in 1G\n",
8977 params->port);
8978 } else {
8979 link_up = 0;
8980 DP(NETIF_MSG_LINK, "port %x: External link is down\n",
8981 params->port);
8982 }
8983
8984 /* Capture 10G link fault. */
8985 if (vars->line_speed == SPEED_10000) {
8986 bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD,
8987 MDIO_PMA_LASI_TXSTAT, &val1);
8988
8989 bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD,
8990 MDIO_PMA_LASI_TXSTAT, &val1);
8991
8992 if (val1 & (1<<0)) {
8993 vars->fault_detected = 1;
8994 }
8995 }
8996
8997 if (link_up) {
8998 bnx2x_ext_phy_resolve_fc(phy, params, vars);
8999 vars->duplex = DUPLEX_FULL;
9000 DP(NETIF_MSG_LINK, "duplex = 0x%x\n", vars->duplex);
9001 }
9002
9003 if ((DUAL_MEDIA(params)) &&
9004 (phy->req_line_speed == SPEED_1000)) {
9005 bnx2x_cl45_read(bp, phy,
9006 MDIO_PMA_DEVAD,
9007 MDIO_PMA_REG_8727_PCS_GP, &val1);
9008 /*
9009 * In case of dual-media board and 1G, power up the XAUI side,
9010 * otherwise power it down. For 10G it is done automatically
9011 */
9012 if (link_up)
9013 val1 &= ~(3<<10);
9014 else
9015 val1 |= (3<<10);
9016 bnx2x_cl45_write(bp, phy,
9017 MDIO_PMA_DEVAD,
9018 MDIO_PMA_REG_8727_PCS_GP, val1);
9019 }
9020 return link_up;
9021 }
9022
9023 static void bnx2x_8727_link_reset(struct bnx2x_phy *phy,
9024 struct link_params *params)
9025 {
9026 struct bnx2x *bp = params->bp;
9027
9028 /* Enable/Disable PHY transmitter output */
9029 bnx2x_set_disable_pmd_transmit(params, phy, 1);
9030
9031 /* Disable Transmitter */
9032 bnx2x_sfp_set_transmitter(params, phy, 0);
9033 /* Clear LASI */
9034 bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_LASI_CTRL, 0);
9035
9036 }
9037
9038 /******************************************************************/
9039 /* BCM8481/BCM84823/BCM84833 PHY SECTION */
9040 /******************************************************************/
9041 static void bnx2x_save_848xx_spirom_version(struct bnx2x_phy *phy,
9042 struct link_params *params)
9043 {
9044 u16 val, fw_ver1, fw_ver2, cnt;
9045 u8 port;
9046 struct bnx2x *bp = params->bp;
9047
9048 port = params->port;
9049
9050 /* For the 32 bits registers in 848xx, access via MDIO2ARM interface.*/
9051 /* (1) set register 0xc200_0014(SPI_BRIDGE_CTRL_2) to 0x03000000 */
9052 bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA819, 0x0014);
9053 bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA81A, 0xc200);
9054 bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA81B, 0x0000);
9055 bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA81C, 0x0300);
9056 bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA817, 0x0009);
9057
9058 for (cnt = 0; cnt < 100; cnt++) {
9059 bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, 0xA818, &val);
9060 if (val & 1)
9061 break;
9062 udelay(5);
9063 }
9064 if (cnt == 100) {
9065 DP(NETIF_MSG_LINK, "Unable to read 848xx phy fw version(1)\n");
9066 bnx2x_save_spirom_version(bp, port, 0,
9067 phy->ver_addr);
9068 return;
9069 }
9070
9071
9072 /* 2) read register 0xc200_0000 (SPI_FW_STATUS) */
9073 bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA819, 0x0000);
9074 bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA81A, 0xc200);
9075 bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA817, 0x000A);
9076 for (cnt = 0; cnt < 100; cnt++) {
9077 bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, 0xA818, &val);
9078 if (val & 1)
9079 break;
9080 udelay(5);
9081 }
9082 if (cnt == 100) {
9083 DP(NETIF_MSG_LINK, "Unable to read 848xx phy fw version(2)\n");
9084 bnx2x_save_spirom_version(bp, port, 0,
9085 phy->ver_addr);
9086 return;
9087 }
9088
9089 /* lower 16 bits of the register SPI_FW_STATUS */
9090 bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, 0xA81B, &fw_ver1);
9091 /* upper 16 bits of register SPI_FW_STATUS */
9092 bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, 0xA81C, &fw_ver2);
9093
9094 bnx2x_save_spirom_version(bp, port, (fw_ver2<<16) | fw_ver1,
9095 phy->ver_addr);
9096 }
9097
9098 static void bnx2x_848xx_set_led(struct bnx2x *bp,
9099 struct bnx2x_phy *phy)
9100 {
9101 u16 val;
9102
9103 /* PHYC_CTL_LED_CTL */
9104 bnx2x_cl45_read(bp, phy,
9105 MDIO_PMA_DEVAD,
9106 MDIO_PMA_REG_8481_LINK_SIGNAL, &val);
9107 val &= 0xFE00;
9108 val |= 0x0092;
9109
9110 bnx2x_cl45_write(bp, phy,
9111 MDIO_PMA_DEVAD,
9112 MDIO_PMA_REG_8481_LINK_SIGNAL, val);
9113
9114 bnx2x_cl45_write(bp, phy,
9115 MDIO_PMA_DEVAD,
9116 MDIO_PMA_REG_8481_LED1_MASK,
9117 0x80);
9118
9119 bnx2x_cl45_write(bp, phy,
9120 MDIO_PMA_DEVAD,
9121 MDIO_PMA_REG_8481_LED2_MASK,
9122 0x18);
9123
9124 /* Select activity source by Tx and Rx, as suggested by PHY AE */
9125 bnx2x_cl45_write(bp, phy,
9126 MDIO_PMA_DEVAD,
9127 MDIO_PMA_REG_8481_LED3_MASK,
9128 0x0006);
9129
9130 /* Select the closest activity blink rate to that in 10/100/1000 */
9131 bnx2x_cl45_write(bp, phy,
9132 MDIO_PMA_DEVAD,
9133 MDIO_PMA_REG_8481_LED3_BLINK,
9134 0);
9135
9136 bnx2x_cl45_read(bp, phy,
9137 MDIO_PMA_DEVAD,
9138 MDIO_PMA_REG_84823_CTL_LED_CTL_1, &val);
9139 val |= MDIO_PMA_REG_84823_LED3_STRETCH_EN; /* stretch_en for LED3*/
9140
9141 bnx2x_cl45_write(bp, phy,
9142 MDIO_PMA_DEVAD,
9143 MDIO_PMA_REG_84823_CTL_LED_CTL_1, val);
9144
9145 /* 'Interrupt Mask' */
9146 bnx2x_cl45_write(bp, phy,
9147 MDIO_AN_DEVAD,
9148 0xFFFB, 0xFFFD);
9149 }
9150
9151 static int bnx2x_848xx_cmn_config_init(struct bnx2x_phy *phy,
9152 struct link_params *params,
9153 struct link_vars *vars)
9154 {
9155 struct bnx2x *bp = params->bp;
9156 u16 autoneg_val, an_1000_val, an_10_100_val;
9157 u16 tmp_req_line_speed;
9158
9159 tmp_req_line_speed = phy->req_line_speed;
9160 if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833)
9161 if (phy->req_line_speed == SPEED_10000)
9162 phy->req_line_speed = SPEED_AUTO_NEG;
9163
9164 /*
9165 * This phy uses the NIG latch mechanism since link indication
9166 * arrives through its LED4 and not via its LASI signal, so we
9167 * get steady signal instead of clear on read
9168 */
9169 bnx2x_bits_en(bp, NIG_REG_LATCH_BC_0 + params->port*4,
9170 1 << NIG_LATCH_BC_ENABLE_MI_INT);
9171
9172 bnx2x_cl45_write(bp, phy,
9173 MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0x0000);
9174
9175 bnx2x_848xx_set_led(bp, phy);
9176
9177 /* set 1000 speed advertisement */
9178 bnx2x_cl45_read(bp, phy,
9179 MDIO_AN_DEVAD, MDIO_AN_REG_8481_1000T_CTRL,
9180 &an_1000_val);
9181
9182 bnx2x_ext_phy_set_pause(params, phy, vars);
9183 bnx2x_cl45_read(bp, phy,
9184 MDIO_AN_DEVAD,
9185 MDIO_AN_REG_8481_LEGACY_AN_ADV,
9186 &an_10_100_val);
9187 bnx2x_cl45_read(bp, phy,
9188 MDIO_AN_DEVAD, MDIO_AN_REG_8481_LEGACY_MII_CTRL,
9189 &autoneg_val);
9190 /* Disable forced speed */
9191 autoneg_val &= ~((1<<6) | (1<<8) | (1<<9) | (1<<12) | (1<<13));
9192 an_10_100_val &= ~((1<<5) | (1<<6) | (1<<7) | (1<<8));
9193
9194 if (((phy->req_line_speed == SPEED_AUTO_NEG) &&
9195 (phy->speed_cap_mask &
9196 PORT_HW_CFG_SPEED_CAPABILITY_D0_1G)) ||
9197 (phy->req_line_speed == SPEED_1000)) {
9198 an_1000_val |= (1<<8);
9199 autoneg_val |= (1<<9 | 1<<12);
9200 if (phy->req_duplex == DUPLEX_FULL)
9201 an_1000_val |= (1<<9);
9202 DP(NETIF_MSG_LINK, "Advertising 1G\n");
9203 } else
9204 an_1000_val &= ~((1<<8) | (1<<9));
9205
9206 bnx2x_cl45_write(bp, phy,
9207 MDIO_AN_DEVAD, MDIO_AN_REG_8481_1000T_CTRL,
9208 an_1000_val);
9209
9210 /* set 100 speed advertisement */
9211 if (((phy->req_line_speed == SPEED_AUTO_NEG) &&
9212 (phy->speed_cap_mask &
9213 (PORT_HW_CFG_SPEED_CAPABILITY_D0_100M_FULL |
9214 PORT_HW_CFG_SPEED_CAPABILITY_D0_100M_HALF)) &&
9215 (phy->supported &
9216 (SUPPORTED_100baseT_Half |
9217 SUPPORTED_100baseT_Full)))) {
9218 an_10_100_val |= (1<<7);
9219 /* Enable autoneg and restart autoneg for legacy speeds */
9220 autoneg_val |= (1<<9 | 1<<12);
9221
9222 if (phy->req_duplex == DUPLEX_FULL)
9223 an_10_100_val |= (1<<8);
9224 DP(NETIF_MSG_LINK, "Advertising 100M\n");
9225 }
9226 /* set 10 speed advertisement */
9227 if (((phy->req_line_speed == SPEED_AUTO_NEG) &&
9228 (phy->speed_cap_mask &
9229 (PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_FULL |
9230 PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_HALF)) &&
9231 (phy->supported &
9232 (SUPPORTED_10baseT_Half |
9233 SUPPORTED_10baseT_Full)))) {
9234 an_10_100_val |= (1<<5);
9235 autoneg_val |= (1<<9 | 1<<12);
9236 if (phy->req_duplex == DUPLEX_FULL)
9237 an_10_100_val |= (1<<6);
9238 DP(NETIF_MSG_LINK, "Advertising 10M\n");
9239 }
9240
9241 /* Only 10/100 are allowed to work in FORCE mode */
9242 if ((phy->req_line_speed == SPEED_100) &&
9243 (phy->supported &
9244 (SUPPORTED_100baseT_Half |
9245 SUPPORTED_100baseT_Full))) {
9246 autoneg_val |= (1<<13);
9247 /* Enabled AUTO-MDIX when autoneg is disabled */
9248 bnx2x_cl45_write(bp, phy,
9249 MDIO_AN_DEVAD, MDIO_AN_REG_8481_AUX_CTRL,
9250 (1<<15 | 1<<9 | 7<<0));
9251 DP(NETIF_MSG_LINK, "Setting 100M force\n");
9252 }
9253 if ((phy->req_line_speed == SPEED_10) &&
9254 (phy->supported &
9255 (SUPPORTED_10baseT_Half |
9256 SUPPORTED_10baseT_Full))) {
9257 /* Enabled AUTO-MDIX when autoneg is disabled */
9258 bnx2x_cl45_write(bp, phy,
9259 MDIO_AN_DEVAD, MDIO_AN_REG_8481_AUX_CTRL,
9260 (1<<15 | 1<<9 | 7<<0));
9261 DP(NETIF_MSG_LINK, "Setting 10M force\n");
9262 }
9263
9264 bnx2x_cl45_write(bp, phy,
9265 MDIO_AN_DEVAD, MDIO_AN_REG_8481_LEGACY_AN_ADV,
9266 an_10_100_val);
9267
9268 if (phy->req_duplex == DUPLEX_FULL)
9269 autoneg_val |= (1<<8);
9270
9271 /*
9272 * Always write this if this is not 84833.
9273 * For 84833, write it only when it's a forced speed.
9274 */
9275 if ((phy->type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833) ||
9276 ((autoneg_val & (1<<12)) == 0))
9277 bnx2x_cl45_write(bp, phy,
9278 MDIO_AN_DEVAD,
9279 MDIO_AN_REG_8481_LEGACY_MII_CTRL, autoneg_val);
9280
9281 if (((phy->req_line_speed == SPEED_AUTO_NEG) &&
9282 (phy->speed_cap_mask &
9283 PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)) ||
9284 (phy->req_line_speed == SPEED_10000)) {
9285 DP(NETIF_MSG_LINK, "Advertising 10G\n");
9286 /* Restart autoneg for 10G*/
9287
9288 bnx2x_cl45_write(bp, phy,
9289 MDIO_AN_DEVAD, MDIO_AN_REG_CTRL,
9290 0x3200);
9291 } else
9292 bnx2x_cl45_write(bp, phy,
9293 MDIO_AN_DEVAD,
9294 MDIO_AN_REG_8481_10GBASE_T_AN_CTRL,
9295 1);
9296
9297 /* Save spirom version */
9298 bnx2x_save_848xx_spirom_version(phy, params);
9299
9300 phy->req_line_speed = tmp_req_line_speed;
9301
9302 return 0;
9303 }
9304
9305 static int bnx2x_8481_config_init(struct bnx2x_phy *phy,
9306 struct link_params *params,
9307 struct link_vars *vars)
9308 {
9309 struct bnx2x *bp = params->bp;
9310 /* Restore normal power mode*/
9311 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
9312 MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port);
9313
9314 /* HW reset */
9315 bnx2x_ext_phy_hw_reset(bp, params->port);
9316 bnx2x_wait_reset_complete(bp, phy, params);
9317
9318 bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 1<<15);
9319 return bnx2x_848xx_cmn_config_init(phy, params, vars);
9320 }
9321
9322
9323 #define PHY84833_HDSHK_WAIT 300
9324 static int bnx2x_84833_pair_swap_cfg(struct bnx2x_phy *phy,
9325 struct link_params *params,
9326 struct link_vars *vars)
9327 {
9328 u32 idx;
9329 u32 pair_swap;
9330 u16 val;
9331 u16 data;
9332 struct bnx2x *bp = params->bp;
9333 /* Do pair swap */
9334
9335 /* Check for configuration. */
9336 pair_swap = REG_RD(bp, params->shmem_base +
9337 offsetof(struct shmem_region,
9338 dev_info.port_hw_config[params->port].xgbt_phy_cfg)) &
9339 PORT_HW_CFG_RJ45_PAIR_SWAP_MASK;
9340
9341 if (pair_swap == 0)
9342 return 0;
9343
9344 data = (u16)pair_swap;
9345
9346 /* Write CMD_OPEN_OVERRIDE to STATUS reg */
9347 bnx2x_cl45_write(bp, phy, MDIO_CTL_DEVAD,
9348 MDIO_84833_TOP_CFG_SCRATCH_REG2,
9349 PHY84833_CMD_OPEN_OVERRIDE);
9350 for (idx = 0; idx < PHY84833_HDSHK_WAIT; idx++) {
9351 bnx2x_cl45_read(bp, phy, MDIO_CTL_DEVAD,
9352 MDIO_84833_TOP_CFG_SCRATCH_REG2, &val);
9353 if (val == PHY84833_CMD_OPEN_FOR_CMDS)
9354 break;
9355 msleep(1);
9356 }
9357 if (idx >= PHY84833_HDSHK_WAIT) {
9358 DP(NETIF_MSG_LINK, "Pairswap: FW not ready.\n");
9359 return -EINVAL;
9360 }
9361
9362 bnx2x_cl45_write(bp, phy, MDIO_CTL_DEVAD,
9363 MDIO_84833_TOP_CFG_SCRATCH_REG4,
9364 data);
9365 /* Issue pair swap command */
9366 bnx2x_cl45_write(bp, phy, MDIO_CTL_DEVAD,
9367 MDIO_84833_TOP_CFG_SCRATCH_REG0,
9368 PHY84833_DIAG_CMD_PAIR_SWAP_CHANGE);
9369 for (idx = 0; idx < PHY84833_HDSHK_WAIT; idx++) {
9370 bnx2x_cl45_read(bp, phy, MDIO_CTL_DEVAD,
9371 MDIO_84833_TOP_CFG_SCRATCH_REG2, &val);
9372 if ((val == PHY84833_CMD_COMPLETE_PASS) ||
9373 (val == PHY84833_CMD_COMPLETE_ERROR))
9374 break;
9375 msleep(1);
9376 }
9377 if ((idx >= PHY84833_HDSHK_WAIT) ||
9378 (val == PHY84833_CMD_COMPLETE_ERROR)) {
9379 DP(NETIF_MSG_LINK, "Pairswap: override failed.\n");
9380 return -EINVAL;
9381 }
9382 bnx2x_cl45_write(bp, phy, MDIO_CTL_DEVAD,
9383 MDIO_84833_TOP_CFG_SCRATCH_REG2,
9384 PHY84833_CMD_CLEAR_COMPLETE);
9385 DP(NETIF_MSG_LINK, "Pairswap OK, val=0x%x\n", data);
9386 return 0;
9387 }
9388
9389
9390 static u8 bnx2x_84833_get_reset_gpios(struct bnx2x *bp,
9391 u32 shmem_base_path[],
9392 u32 chip_id)
9393 {
9394 u32 reset_pin[2];
9395 u32 idx;
9396 u8 reset_gpios;
9397 if (CHIP_IS_E3(bp)) {
9398 /* Assume that these will be GPIOs, not EPIOs. */
9399 for (idx = 0; idx < 2; idx++) {
9400 /* Map config param to register bit. */
9401 reset_pin[idx] = REG_RD(bp, shmem_base_path[idx] +
9402 offsetof(struct shmem_region,
9403 dev_info.port_hw_config[0].e3_cmn_pin_cfg));
9404 reset_pin[idx] = (reset_pin[idx] &
9405 PORT_HW_CFG_E3_PHY_RESET_MASK) >>
9406 PORT_HW_CFG_E3_PHY_RESET_SHIFT;
9407 reset_pin[idx] -= PIN_CFG_GPIO0_P0;
9408 reset_pin[idx] = (1 << reset_pin[idx]);
9409 }
9410 reset_gpios = (u8)(reset_pin[0] | reset_pin[1]);
9411 } else {
9412 /* E2, look from diff place of shmem. */
9413 for (idx = 0; idx < 2; idx++) {
9414 reset_pin[idx] = REG_RD(bp, shmem_base_path[idx] +
9415 offsetof(struct shmem_region,
9416 dev_info.port_hw_config[0].default_cfg));
9417 reset_pin[idx] &= PORT_HW_CFG_EXT_PHY_GPIO_RST_MASK;
9418 reset_pin[idx] -= PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO0_P0;
9419 reset_pin[idx] >>= PORT_HW_CFG_EXT_PHY_GPIO_RST_SHIFT;
9420 reset_pin[idx] = (1 << reset_pin[idx]);
9421 }
9422 reset_gpios = (u8)(reset_pin[0] | reset_pin[1]);
9423 }
9424
9425 return reset_gpios;
9426 }
9427
9428 static int bnx2x_84833_hw_reset_phy(struct bnx2x_phy *phy,
9429 struct link_params *params)
9430 {
9431 struct bnx2x *bp = params->bp;
9432 u8 reset_gpios;
9433 u32 other_shmem_base_addr = REG_RD(bp, params->shmem2_base +
9434 offsetof(struct shmem2_region,
9435 other_shmem_base_addr));
9436
9437 u32 shmem_base_path[2];
9438 shmem_base_path[0] = params->shmem_base;
9439 shmem_base_path[1] = other_shmem_base_addr;
9440
9441 reset_gpios = bnx2x_84833_get_reset_gpios(bp, shmem_base_path,
9442 params->chip_id);
9443
9444 bnx2x_set_mult_gpio(bp, reset_gpios, MISC_REGISTERS_GPIO_OUTPUT_LOW);
9445 udelay(10);
9446 DP(NETIF_MSG_LINK, "84833 hw reset on pin values 0x%x\n",
9447 reset_gpios);
9448
9449 return 0;
9450 }
9451
9452 static int bnx2x_84833_common_init_phy(struct bnx2x *bp,
9453 u32 shmem_base_path[],
9454 u32 chip_id)
9455 {
9456 u8 reset_gpios;
9457
9458 reset_gpios = bnx2x_84833_get_reset_gpios(bp, shmem_base_path, chip_id);
9459
9460 bnx2x_set_mult_gpio(bp, reset_gpios, MISC_REGISTERS_GPIO_OUTPUT_LOW);
9461 udelay(10);
9462 bnx2x_set_mult_gpio(bp, reset_gpios, MISC_REGISTERS_GPIO_OUTPUT_HIGH);
9463 msleep(800);
9464 DP(NETIF_MSG_LINK, "84833 reset pulse on pin values 0x%x\n",
9465 reset_gpios);
9466
9467 return 0;
9468 }
9469
9470 #define PHY84833_CONSTANT_LATENCY 1193
9471 static int bnx2x_848x3_config_init(struct bnx2x_phy *phy,
9472 struct link_params *params,
9473 struct link_vars *vars)
9474 {
9475 struct bnx2x *bp = params->bp;
9476 u8 port, initialize = 1;
9477 u16 val;
9478 u16 temp;
9479 u32 actual_phy_selection, cms_enable, idx;
9480 int rc = 0;
9481
9482 msleep(1);
9483
9484 if (!(CHIP_IS_E1(bp)))
9485 port = BP_PATH(bp);
9486 else
9487 port = params->port;
9488
9489 if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823) {
9490 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_3,
9491 MISC_REGISTERS_GPIO_OUTPUT_HIGH,
9492 port);
9493 } else {
9494 /* MDIO reset */
9495 bnx2x_cl45_write(bp, phy,
9496 MDIO_PMA_DEVAD,
9497 MDIO_PMA_REG_CTRL, 0x8000);
9498 /* Bring PHY out of super isolate mode */
9499 bnx2x_cl45_read(bp, phy,
9500 MDIO_CTL_DEVAD,
9501 MDIO_84833_TOP_CFG_XGPHY_STRAP1, &val);
9502 val &= ~MDIO_84833_SUPER_ISOLATE;
9503 bnx2x_cl45_write(bp, phy,
9504 MDIO_CTL_DEVAD,
9505 MDIO_84833_TOP_CFG_XGPHY_STRAP1, val);
9506 }
9507
9508 bnx2x_wait_reset_complete(bp, phy, params);
9509
9510 /* Wait for GPHY to come out of reset */
9511 msleep(50);
9512
9513 if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833)
9514 bnx2x_84833_pair_swap_cfg(phy, params, vars);
9515
9516 /*
9517 * BCM84823 requires that XGXS links up first @ 10G for normal behavior
9518 */
9519 temp = vars->line_speed;
9520 vars->line_speed = SPEED_10000;
9521 bnx2x_set_autoneg(&params->phy[INT_PHY], params, vars, 0);
9522 bnx2x_program_serdes(&params->phy[INT_PHY], params, vars);
9523 vars->line_speed = temp;
9524
9525 /* Set dual-media configuration according to configuration */
9526
9527 bnx2x_cl45_read(bp, phy, MDIO_CTL_DEVAD,
9528 MDIO_CTL_REG_84823_MEDIA, &val);
9529 val &= ~(MDIO_CTL_REG_84823_MEDIA_MAC_MASK |
9530 MDIO_CTL_REG_84823_MEDIA_LINE_MASK |
9531 MDIO_CTL_REG_84823_MEDIA_COPPER_CORE_DOWN |
9532 MDIO_CTL_REG_84823_MEDIA_PRIORITY_MASK |
9533 MDIO_CTL_REG_84823_MEDIA_FIBER_1G);
9534
9535 if (CHIP_IS_E3(bp)) {
9536 val &= ~(MDIO_CTL_REG_84823_MEDIA_MAC_MASK |
9537 MDIO_CTL_REG_84823_MEDIA_LINE_MASK);
9538 } else {
9539 val |= (MDIO_CTL_REG_84823_CTRL_MAC_XFI |
9540 MDIO_CTL_REG_84823_MEDIA_LINE_XAUI_L);
9541 }
9542
9543 actual_phy_selection = bnx2x_phy_selection(params);
9544
9545 switch (actual_phy_selection) {
9546 case PORT_HW_CFG_PHY_SELECTION_HARDWARE_DEFAULT:
9547 /* Do nothing. Essentially this is like the priority copper */
9548 break;
9549 case PORT_HW_CFG_PHY_SELECTION_FIRST_PHY_PRIORITY:
9550 val |= MDIO_CTL_REG_84823_MEDIA_PRIORITY_COPPER;
9551 break;
9552 case PORT_HW_CFG_PHY_SELECTION_SECOND_PHY_PRIORITY:
9553 val |= MDIO_CTL_REG_84823_MEDIA_PRIORITY_FIBER;
9554 break;
9555 case PORT_HW_CFG_PHY_SELECTION_FIRST_PHY:
9556 /* Do nothing here. The first PHY won't be initialized at all */
9557 break;
9558 case PORT_HW_CFG_PHY_SELECTION_SECOND_PHY:
9559 val |= MDIO_CTL_REG_84823_MEDIA_COPPER_CORE_DOWN;
9560 initialize = 0;
9561 break;
9562 }
9563 if (params->phy[EXT_PHY2].req_line_speed == SPEED_1000)
9564 val |= MDIO_CTL_REG_84823_MEDIA_FIBER_1G;
9565
9566 bnx2x_cl45_write(bp, phy, MDIO_CTL_DEVAD,
9567 MDIO_CTL_REG_84823_MEDIA, val);
9568 DP(NETIF_MSG_LINK, "Multi_phy config = 0x%x, Media control = 0x%x\n",
9569 params->multi_phy_config, val);
9570
9571 /* AutogrEEEn */
9572 if (params->feature_config_flags &
9573 FEATURE_CONFIG_AUTOGREEEN_ENABLED) {
9574 /* Ensure that f/w is ready */
9575 for (idx = 0; idx < PHY84833_HDSHK_WAIT; idx++) {
9576 bnx2x_cl45_read(bp, phy, MDIO_CTL_DEVAD,
9577 MDIO_84833_TOP_CFG_SCRATCH_REG2, &val);
9578 if (val == PHY84833_CMD_OPEN_FOR_CMDS)
9579 break;
9580 usleep_range(1000, 1000);
9581 }
9582 if (idx >= PHY84833_HDSHK_WAIT) {
9583 DP(NETIF_MSG_LINK, "AutogrEEEn: FW not ready.\n");
9584 return -EINVAL;
9585 }
9586
9587 /* Select EEE mode */
9588 bnx2x_cl45_write(bp, phy, MDIO_CTL_DEVAD,
9589 MDIO_84833_TOP_CFG_SCRATCH_REG3,
9590 0x2);
9591
9592 /* Set Idle and Latency */
9593 bnx2x_cl45_write(bp, phy, MDIO_CTL_DEVAD,
9594 MDIO_84833_TOP_CFG_SCRATCH_REG4,
9595 PHY84833_CONSTANT_LATENCY + 1);
9596
9597 bnx2x_cl45_write(bp, phy, MDIO_CTL_DEVAD,
9598 MDIO_84833_TOP_CFG_DATA3_REG,
9599 PHY84833_CONSTANT_LATENCY + 1);
9600
9601 bnx2x_cl45_write(bp, phy, MDIO_CTL_DEVAD,
9602 MDIO_84833_TOP_CFG_DATA4_REG,
9603 PHY84833_CONSTANT_LATENCY);
9604
9605 /* Send EEE instruction to command register */
9606 bnx2x_cl45_write(bp, phy, MDIO_CTL_DEVAD,
9607 MDIO_84833_TOP_CFG_SCRATCH_REG0,
9608 PHY84833_DIAG_CMD_SET_EEE_MODE);
9609
9610 /* Ensure that the command has completed */
9611 for (idx = 0; idx < PHY84833_HDSHK_WAIT; idx++) {
9612 bnx2x_cl45_read(bp, phy, MDIO_CTL_DEVAD,
9613 MDIO_84833_TOP_CFG_SCRATCH_REG2, &val);
9614 if ((val == PHY84833_CMD_COMPLETE_PASS) ||
9615 (val == PHY84833_CMD_COMPLETE_ERROR))
9616 break;
9617 usleep_range(1000, 1000);
9618 }
9619 if ((idx >= PHY84833_HDSHK_WAIT) ||
9620 (val == PHY84833_CMD_COMPLETE_ERROR)) {
9621 DP(NETIF_MSG_LINK, "AutogrEEEn: command failed.\n");
9622 return -EINVAL;
9623 }
9624
9625 /* Reset command handler */
9626 bnx2x_cl45_write(bp, phy, MDIO_CTL_DEVAD,
9627 MDIO_84833_TOP_CFG_SCRATCH_REG2,
9628 PHY84833_CMD_CLEAR_COMPLETE);
9629 }
9630
9631 if (initialize)
9632 rc = bnx2x_848xx_cmn_config_init(phy, params, vars);
9633 else
9634 bnx2x_save_848xx_spirom_version(phy, params);
9635 /* 84833 PHY has a better feature and doesn't need to support this. */
9636 if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823) {
9637 cms_enable = REG_RD(bp, params->shmem_base +
9638 offsetof(struct shmem_region,
9639 dev_info.port_hw_config[params->port].default_cfg)) &
9640 PORT_HW_CFG_ENABLE_CMS_MASK;
9641
9642 bnx2x_cl45_read(bp, phy, MDIO_CTL_DEVAD,
9643 MDIO_CTL_REG_84823_USER_CTRL_REG, &val);
9644 if (cms_enable)
9645 val |= MDIO_CTL_REG_84823_USER_CTRL_CMS;
9646 else
9647 val &= ~MDIO_CTL_REG_84823_USER_CTRL_CMS;
9648 bnx2x_cl45_write(bp, phy, MDIO_CTL_DEVAD,
9649 MDIO_CTL_REG_84823_USER_CTRL_REG, val);
9650 }
9651
9652 return rc;
9653 }
9654
9655 static u8 bnx2x_848xx_read_status(struct bnx2x_phy *phy,
9656 struct link_params *params,
9657 struct link_vars *vars)
9658 {
9659 struct bnx2x *bp = params->bp;
9660 u16 val, val1, val2;
9661 u8 link_up = 0;
9662
9663
9664 /* Check 10G-BaseT link status */
9665 /* Check PMD signal ok */
9666 bnx2x_cl45_read(bp, phy,
9667 MDIO_AN_DEVAD, 0xFFFA, &val1);
9668 bnx2x_cl45_read(bp, phy,
9669 MDIO_PMA_DEVAD, MDIO_PMA_REG_8481_PMD_SIGNAL,
9670 &val2);
9671 DP(NETIF_MSG_LINK, "BCM848xx: PMD_SIGNAL 1.a811 = 0x%x\n", val2);
9672
9673 /* Check link 10G */
9674 if (val2 & (1<<11)) {
9675 vars->line_speed = SPEED_10000;
9676 vars->duplex = DUPLEX_FULL;
9677 link_up = 1;
9678 bnx2x_ext_phy_10G_an_resolve(bp, phy, vars);
9679 } else { /* Check Legacy speed link */
9680 u16 legacy_status, legacy_speed;
9681
9682 /* Enable expansion register 0x42 (Operation mode status) */
9683 bnx2x_cl45_write(bp, phy,
9684 MDIO_AN_DEVAD,
9685 MDIO_AN_REG_8481_EXPANSION_REG_ACCESS, 0xf42);
9686
9687 /* Get legacy speed operation status */
9688 bnx2x_cl45_read(bp, phy,
9689 MDIO_AN_DEVAD,
9690 MDIO_AN_REG_8481_EXPANSION_REG_RD_RW,
9691 &legacy_status);
9692
9693 DP(NETIF_MSG_LINK, "Legacy speed status"
9694 " = 0x%x\n", legacy_status);
9695 link_up = ((legacy_status & (1<<11)) == (1<<11));
9696 if (link_up) {
9697 legacy_speed = (legacy_status & (3<<9));
9698 if (legacy_speed == (0<<9))
9699 vars->line_speed = SPEED_10;
9700 else if (legacy_speed == (1<<9))
9701 vars->line_speed = SPEED_100;
9702 else if (legacy_speed == (2<<9))
9703 vars->line_speed = SPEED_1000;
9704 else /* Should not happen */
9705 vars->line_speed = 0;
9706
9707 if (legacy_status & (1<<8))
9708 vars->duplex = DUPLEX_FULL;
9709 else
9710 vars->duplex = DUPLEX_HALF;
9711
9712 DP(NETIF_MSG_LINK, "Link is up in %dMbps,"
9713 " is_duplex_full= %d\n", vars->line_speed,
9714 (vars->duplex == DUPLEX_FULL));
9715 /* Check legacy speed AN resolution */
9716 bnx2x_cl45_read(bp, phy,
9717 MDIO_AN_DEVAD,
9718 MDIO_AN_REG_8481_LEGACY_MII_STATUS,
9719 &val);
9720 if (val & (1<<5))
9721 vars->link_status |=
9722 LINK_STATUS_AUTO_NEGOTIATE_COMPLETE;
9723 bnx2x_cl45_read(bp, phy,
9724 MDIO_AN_DEVAD,
9725 MDIO_AN_REG_8481_LEGACY_AN_EXPANSION,
9726 &val);
9727 if ((val & (1<<0)) == 0)
9728 vars->link_status |=
9729 LINK_STATUS_PARALLEL_DETECTION_USED;
9730 }
9731 }
9732 if (link_up) {
9733 DP(NETIF_MSG_LINK, "BCM84823: link speed is %d\n",
9734 vars->line_speed);
9735 bnx2x_ext_phy_resolve_fc(phy, params, vars);
9736 }
9737
9738 return link_up;
9739 }
9740
9741
9742 static int bnx2x_848xx_format_ver(u32 raw_ver, u8 *str, u16 *len)
9743 {
9744 int status = 0;
9745 u32 spirom_ver;
9746 spirom_ver = ((raw_ver & 0xF80) >> 7) << 16 | (raw_ver & 0x7F);
9747 status = bnx2x_format_ver(spirom_ver, str, len);
9748 return status;
9749 }
9750
9751 static void bnx2x_8481_hw_reset(struct bnx2x_phy *phy,
9752 struct link_params *params)
9753 {
9754 bnx2x_set_gpio(params->bp, MISC_REGISTERS_GPIO_1,
9755 MISC_REGISTERS_GPIO_OUTPUT_LOW, 0);
9756 bnx2x_set_gpio(params->bp, MISC_REGISTERS_GPIO_1,
9757 MISC_REGISTERS_GPIO_OUTPUT_LOW, 1);
9758 }
9759
9760 static void bnx2x_8481_link_reset(struct bnx2x_phy *phy,
9761 struct link_params *params)
9762 {
9763 bnx2x_cl45_write(params->bp, phy,
9764 MDIO_AN_DEVAD, MDIO_AN_REG_CTRL, 0x0000);
9765 bnx2x_cl45_write(params->bp, phy,
9766 MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 1);
9767 }
9768
9769 static void bnx2x_848x3_link_reset(struct bnx2x_phy *phy,
9770 struct link_params *params)
9771 {
9772 struct bnx2x *bp = params->bp;
9773 u8 port;
9774 u16 val16;
9775
9776 if (!(CHIP_IS_E1(bp)))
9777 port = BP_PATH(bp);
9778 else
9779 port = params->port;
9780
9781 if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823) {
9782 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_3,
9783 MISC_REGISTERS_GPIO_OUTPUT_LOW,
9784 port);
9785 } else {
9786 bnx2x_cl45_read(bp, phy,
9787 MDIO_CTL_DEVAD,
9788 0x400f, &val16);
9789 bnx2x_cl45_write(bp, phy,
9790 MDIO_PMA_DEVAD,
9791 MDIO_PMA_REG_CTRL, 0x800);
9792 }
9793 }
9794
9795 static void bnx2x_848xx_set_link_led(struct bnx2x_phy *phy,
9796 struct link_params *params, u8 mode)
9797 {
9798 struct bnx2x *bp = params->bp;
9799 u16 val;
9800 u8 port;
9801
9802 if (!(CHIP_IS_E1(bp)))
9803 port = BP_PATH(bp);
9804 else
9805 port = params->port;
9806
9807 switch (mode) {
9808 case LED_MODE_OFF:
9809
9810 DP(NETIF_MSG_LINK, "Port 0x%x: LED MODE OFF\n", port);
9811
9812 if ((params->hw_led_mode << SHARED_HW_CFG_LED_MODE_SHIFT) ==
9813 SHARED_HW_CFG_LED_EXTPHY1) {
9814
9815 /* Set LED masks */
9816 bnx2x_cl45_write(bp, phy,
9817 MDIO_PMA_DEVAD,
9818 MDIO_PMA_REG_8481_LED1_MASK,
9819 0x0);
9820
9821 bnx2x_cl45_write(bp, phy,
9822 MDIO_PMA_DEVAD,
9823 MDIO_PMA_REG_8481_LED2_MASK,
9824 0x0);
9825
9826 bnx2x_cl45_write(bp, phy,
9827 MDIO_PMA_DEVAD,
9828 MDIO_PMA_REG_8481_LED3_MASK,
9829 0x0);
9830
9831 bnx2x_cl45_write(bp, phy,
9832 MDIO_PMA_DEVAD,
9833 MDIO_PMA_REG_8481_LED5_MASK,
9834 0x0);
9835
9836 } else {
9837 bnx2x_cl45_write(bp, phy,
9838 MDIO_PMA_DEVAD,
9839 MDIO_PMA_REG_8481_LED1_MASK,
9840 0x0);
9841 }
9842 break;
9843 case LED_MODE_FRONT_PANEL_OFF:
9844
9845 DP(NETIF_MSG_LINK, "Port 0x%x: LED MODE FRONT PANEL OFF\n",
9846 port);
9847
9848 if ((params->hw_led_mode << SHARED_HW_CFG_LED_MODE_SHIFT) ==
9849 SHARED_HW_CFG_LED_EXTPHY1) {
9850
9851 /* Set LED masks */
9852 bnx2x_cl45_write(bp, phy,
9853 MDIO_PMA_DEVAD,
9854 MDIO_PMA_REG_8481_LED1_MASK,
9855 0x0);
9856
9857 bnx2x_cl45_write(bp, phy,
9858 MDIO_PMA_DEVAD,
9859 MDIO_PMA_REG_8481_LED2_MASK,
9860 0x0);
9861
9862 bnx2x_cl45_write(bp, phy,
9863 MDIO_PMA_DEVAD,
9864 MDIO_PMA_REG_8481_LED3_MASK,
9865 0x0);
9866
9867 bnx2x_cl45_write(bp, phy,
9868 MDIO_PMA_DEVAD,
9869 MDIO_PMA_REG_8481_LED5_MASK,
9870 0x20);
9871
9872 } else {
9873 bnx2x_cl45_write(bp, phy,
9874 MDIO_PMA_DEVAD,
9875 MDIO_PMA_REG_8481_LED1_MASK,
9876 0x0);
9877 }
9878 break;
9879 case LED_MODE_ON:
9880
9881 DP(NETIF_MSG_LINK, "Port 0x%x: LED MODE ON\n", port);
9882
9883 if ((params->hw_led_mode << SHARED_HW_CFG_LED_MODE_SHIFT) ==
9884 SHARED_HW_CFG_LED_EXTPHY1) {
9885 /* Set control reg */
9886 bnx2x_cl45_read(bp, phy,
9887 MDIO_PMA_DEVAD,
9888 MDIO_PMA_REG_8481_LINK_SIGNAL,
9889 &val);
9890 val &= 0x8000;
9891 val |= 0x2492;
9892
9893 bnx2x_cl45_write(bp, phy,
9894 MDIO_PMA_DEVAD,
9895 MDIO_PMA_REG_8481_LINK_SIGNAL,
9896 val);
9897
9898 /* Set LED masks */
9899 bnx2x_cl45_write(bp, phy,
9900 MDIO_PMA_DEVAD,
9901 MDIO_PMA_REG_8481_LED1_MASK,
9902 0x0);
9903
9904 bnx2x_cl45_write(bp, phy,
9905 MDIO_PMA_DEVAD,
9906 MDIO_PMA_REG_8481_LED2_MASK,
9907 0x20);
9908
9909 bnx2x_cl45_write(bp, phy,
9910 MDIO_PMA_DEVAD,
9911 MDIO_PMA_REG_8481_LED3_MASK,
9912 0x20);
9913
9914 bnx2x_cl45_write(bp, phy,
9915 MDIO_PMA_DEVAD,
9916 MDIO_PMA_REG_8481_LED5_MASK,
9917 0x0);
9918 } else {
9919 bnx2x_cl45_write(bp, phy,
9920 MDIO_PMA_DEVAD,
9921 MDIO_PMA_REG_8481_LED1_MASK,
9922 0x20);
9923 }
9924 break;
9925
9926 case LED_MODE_OPER:
9927
9928 DP(NETIF_MSG_LINK, "Port 0x%x: LED MODE OPER\n", port);
9929
9930 if ((params->hw_led_mode << SHARED_HW_CFG_LED_MODE_SHIFT) ==
9931 SHARED_HW_CFG_LED_EXTPHY1) {
9932
9933 /* Set control reg */
9934 bnx2x_cl45_read(bp, phy,
9935 MDIO_PMA_DEVAD,
9936 MDIO_PMA_REG_8481_LINK_SIGNAL,
9937 &val);
9938
9939 if (!((val &
9940 MDIO_PMA_REG_8481_LINK_SIGNAL_LED4_ENABLE_MASK)
9941 >> MDIO_PMA_REG_8481_LINK_SIGNAL_LED4_ENABLE_SHIFT)) {
9942 DP(NETIF_MSG_LINK, "Setting LINK_SIGNAL\n");
9943 bnx2x_cl45_write(bp, phy,
9944 MDIO_PMA_DEVAD,
9945 MDIO_PMA_REG_8481_LINK_SIGNAL,
9946 0xa492);
9947 }
9948
9949 /* Set LED masks */
9950 bnx2x_cl45_write(bp, phy,
9951 MDIO_PMA_DEVAD,
9952 MDIO_PMA_REG_8481_LED1_MASK,
9953 0x10);
9954
9955 bnx2x_cl45_write(bp, phy,
9956 MDIO_PMA_DEVAD,
9957 MDIO_PMA_REG_8481_LED2_MASK,
9958 0x80);
9959
9960 bnx2x_cl45_write(bp, phy,
9961 MDIO_PMA_DEVAD,
9962 MDIO_PMA_REG_8481_LED3_MASK,
9963 0x98);
9964
9965 bnx2x_cl45_write(bp, phy,
9966 MDIO_PMA_DEVAD,
9967 MDIO_PMA_REG_8481_LED5_MASK,
9968 0x40);
9969
9970 } else {
9971 bnx2x_cl45_write(bp, phy,
9972 MDIO_PMA_DEVAD,
9973 MDIO_PMA_REG_8481_LED1_MASK,
9974 0x80);
9975
9976 /* Tell LED3 to blink on source */
9977 bnx2x_cl45_read(bp, phy,
9978 MDIO_PMA_DEVAD,
9979 MDIO_PMA_REG_8481_LINK_SIGNAL,
9980 &val);
9981 val &= ~(7<<6);
9982 val |= (1<<6); /* A83B[8:6]= 1 */
9983 bnx2x_cl45_write(bp, phy,
9984 MDIO_PMA_DEVAD,
9985 MDIO_PMA_REG_8481_LINK_SIGNAL,
9986 val);
9987 }
9988 break;
9989 }
9990
9991 /*
9992 * This is a workaround for E3+84833 until autoneg
9993 * restart is fixed in f/w
9994 */
9995 if (CHIP_IS_E3(bp)) {
9996 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
9997 MDIO_WC_REG_GP2_STATUS_GP_2_1, &val);
9998 }
9999 }
10000
10001 /******************************************************************/
10002 /* 54618SE PHY SECTION */
10003 /******************************************************************/
10004 static int bnx2x_54618se_config_init(struct bnx2x_phy *phy,
10005 struct link_params *params,
10006 struct link_vars *vars)
10007 {
10008 struct bnx2x *bp = params->bp;
10009 u8 port;
10010 u16 autoneg_val, an_1000_val, an_10_100_val, fc_val, temp;
10011 u32 cfg_pin;
10012
10013 DP(NETIF_MSG_LINK, "54618SE cfg init\n");
10014 usleep_range(1000, 1000);
10015
10016 /* This works with E3 only, no need to check the chip
10017 before determining the port. */
10018 port = params->port;
10019
10020 cfg_pin = (REG_RD(bp, params->shmem_base +
10021 offsetof(struct shmem_region,
10022 dev_info.port_hw_config[port].e3_cmn_pin_cfg)) &
10023 PORT_HW_CFG_E3_PHY_RESET_MASK) >>
10024 PORT_HW_CFG_E3_PHY_RESET_SHIFT;
10025
10026 /* Drive pin high to bring the GPHY out of reset. */
10027 bnx2x_set_cfg_pin(bp, cfg_pin, 1);
10028
10029 /* wait for GPHY to reset */
10030 msleep(50);
10031
10032 /* reset phy */
10033 bnx2x_cl22_write(bp, phy,
10034 MDIO_PMA_REG_CTRL, 0x8000);
10035 bnx2x_wait_reset_complete(bp, phy, params);
10036
10037 /*wait for GPHY to reset */
10038 msleep(50);
10039
10040 /* Configure LED4: set to INTR (0x6). */
10041 /* Accessing shadow register 0xe. */
10042 bnx2x_cl22_write(bp, phy,
10043 MDIO_REG_GPHY_SHADOW,
10044 MDIO_REG_GPHY_SHADOW_LED_SEL2);
10045 bnx2x_cl22_read(bp, phy,
10046 MDIO_REG_GPHY_SHADOW,
10047 &temp);
10048 temp &= ~(0xf << 4);
10049 temp |= (0x6 << 4);
10050 bnx2x_cl22_write(bp, phy,
10051 MDIO_REG_GPHY_SHADOW,
10052 MDIO_REG_GPHY_SHADOW_WR_ENA | temp);
10053 /* Configure INTR based on link status change. */
10054 bnx2x_cl22_write(bp, phy,
10055 MDIO_REG_INTR_MASK,
10056 ~MDIO_REG_INTR_MASK_LINK_STATUS);
10057
10058 /* Flip the signal detect polarity (set 0x1c.0x1e[8]). */
10059 bnx2x_cl22_write(bp, phy,
10060 MDIO_REG_GPHY_SHADOW,
10061 MDIO_REG_GPHY_SHADOW_AUTO_DET_MED);
10062 bnx2x_cl22_read(bp, phy,
10063 MDIO_REG_GPHY_SHADOW,
10064 &temp);
10065 temp |= MDIO_REG_GPHY_SHADOW_INVERT_FIB_SD;
10066 bnx2x_cl22_write(bp, phy,
10067 MDIO_REG_GPHY_SHADOW,
10068 MDIO_REG_GPHY_SHADOW_WR_ENA | temp);
10069
10070 /* Set up fc */
10071 /* Please refer to Table 28B-3 of 802.3ab-1999 spec. */
10072 bnx2x_calc_ieee_aneg_adv(phy, params, &vars->ieee_fc);
10073 fc_val = 0;
10074 if ((vars->ieee_fc & MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) ==
10075 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC)
10076 fc_val |= MDIO_AN_REG_ADV_PAUSE_ASYMMETRIC;
10077
10078 if ((vars->ieee_fc & MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) ==
10079 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH)
10080 fc_val |= MDIO_AN_REG_ADV_PAUSE_PAUSE;
10081
10082 /* read all advertisement */
10083 bnx2x_cl22_read(bp, phy,
10084 0x09,
10085 &an_1000_val);
10086
10087 bnx2x_cl22_read(bp, phy,
10088 0x04,
10089 &an_10_100_val);
10090
10091 bnx2x_cl22_read(bp, phy,
10092 MDIO_PMA_REG_CTRL,
10093 &autoneg_val);
10094
10095 /* Disable forced speed */
10096 autoneg_val &= ~((1<<6) | (1<<8) | (1<<9) | (1<<12) | (1<<13));
10097 an_10_100_val &= ~((1<<5) | (1<<6) | (1<<7) | (1<<8) | (1<<10) |
10098 (1<<11));
10099
10100 if (((phy->req_line_speed == SPEED_AUTO_NEG) &&
10101 (phy->speed_cap_mask &
10102 PORT_HW_CFG_SPEED_CAPABILITY_D0_1G)) ||
10103 (phy->req_line_speed == SPEED_1000)) {
10104 an_1000_val |= (1<<8);
10105 autoneg_val |= (1<<9 | 1<<12);
10106 if (phy->req_duplex == DUPLEX_FULL)
10107 an_1000_val |= (1<<9);
10108 DP(NETIF_MSG_LINK, "Advertising 1G\n");
10109 } else
10110 an_1000_val &= ~((1<<8) | (1<<9));
10111
10112 bnx2x_cl22_write(bp, phy,
10113 0x09,
10114 an_1000_val);
10115 bnx2x_cl22_read(bp, phy,
10116 0x09,
10117 &an_1000_val);
10118
10119 /* set 100 speed advertisement */
10120 if (((phy->req_line_speed == SPEED_AUTO_NEG) &&
10121 (phy->speed_cap_mask &
10122 (PORT_HW_CFG_SPEED_CAPABILITY_D0_100M_FULL |
10123 PORT_HW_CFG_SPEED_CAPABILITY_D0_100M_HALF)))) {
10124 an_10_100_val |= (1<<7);
10125 /* Enable autoneg and restart autoneg for legacy speeds */
10126 autoneg_val |= (1<<9 | 1<<12);
10127
10128 if (phy->req_duplex == DUPLEX_FULL)
10129 an_10_100_val |= (1<<8);
10130 DP(NETIF_MSG_LINK, "Advertising 100M\n");
10131 }
10132
10133 /* set 10 speed advertisement */
10134 if (((phy->req_line_speed == SPEED_AUTO_NEG) &&
10135 (phy->speed_cap_mask &
10136 (PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_FULL |
10137 PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_HALF)))) {
10138 an_10_100_val |= (1<<5);
10139 autoneg_val |= (1<<9 | 1<<12);
10140 if (phy->req_duplex == DUPLEX_FULL)
10141 an_10_100_val |= (1<<6);
10142 DP(NETIF_MSG_LINK, "Advertising 10M\n");
10143 }
10144
10145 /* Only 10/100 are allowed to work in FORCE mode */
10146 if (phy->req_line_speed == SPEED_100) {
10147 autoneg_val |= (1<<13);
10148 /* Enabled AUTO-MDIX when autoneg is disabled */
10149 bnx2x_cl22_write(bp, phy,
10150 0x18,
10151 (1<<15 | 1<<9 | 7<<0));
10152 DP(NETIF_MSG_LINK, "Setting 100M force\n");
10153 }
10154 if (phy->req_line_speed == SPEED_10) {
10155 /* Enabled AUTO-MDIX when autoneg is disabled */
10156 bnx2x_cl22_write(bp, phy,
10157 0x18,
10158 (1<<15 | 1<<9 | 7<<0));
10159 DP(NETIF_MSG_LINK, "Setting 10M force\n");
10160 }
10161
10162 /* Check if we should turn on Auto-GrEEEn */
10163 bnx2x_cl22_read(bp, phy, MDIO_REG_GPHY_PHYID_LSB, &temp);
10164 if (temp == MDIO_REG_GPHY_ID_54618SE) {
10165 if (params->feature_config_flags &
10166 FEATURE_CONFIG_AUTOGREEEN_ENABLED) {
10167 temp = 6;
10168 DP(NETIF_MSG_LINK, "Enabling Auto-GrEEEn\n");
10169 } else {
10170 temp = 0;
10171 DP(NETIF_MSG_LINK, "Disabling Auto-GrEEEn\n");
10172 }
10173 bnx2x_cl22_write(bp, phy,
10174 MDIO_REG_GPHY_CL45_ADDR_REG, MDIO_AN_DEVAD);
10175 bnx2x_cl22_write(bp, phy,
10176 MDIO_REG_GPHY_CL45_DATA_REG,
10177 MDIO_REG_GPHY_EEE_ADV);
10178 bnx2x_cl22_write(bp, phy,
10179 MDIO_REG_GPHY_CL45_ADDR_REG,
10180 (0x1 << 14) | MDIO_AN_DEVAD);
10181 bnx2x_cl22_write(bp, phy,
10182 MDIO_REG_GPHY_CL45_DATA_REG,
10183 temp);
10184 }
10185
10186 bnx2x_cl22_write(bp, phy,
10187 0x04,
10188 an_10_100_val | fc_val);
10189
10190 if (phy->req_duplex == DUPLEX_FULL)
10191 autoneg_val |= (1<<8);
10192
10193 bnx2x_cl22_write(bp, phy,
10194 MDIO_PMA_REG_CTRL, autoneg_val);
10195
10196 return 0;
10197 }
10198
10199 static void bnx2x_54618se_set_link_led(struct bnx2x_phy *phy,
10200 struct link_params *params, u8 mode)
10201 {
10202 struct bnx2x *bp = params->bp;
10203 DP(NETIF_MSG_LINK, "54618SE set link led (mode=%x)\n", mode);
10204 switch (mode) {
10205 case LED_MODE_FRONT_PANEL_OFF:
10206 case LED_MODE_OFF:
10207 case LED_MODE_OPER:
10208 case LED_MODE_ON:
10209 default:
10210 break;
10211 }
10212 return;
10213 }
10214
10215 static void bnx2x_54618se_link_reset(struct bnx2x_phy *phy,
10216 struct link_params *params)
10217 {
10218 struct bnx2x *bp = params->bp;
10219 u32 cfg_pin;
10220 u8 port;
10221
10222 /*
10223 * In case of no EPIO routed to reset the GPHY, put it
10224 * in low power mode.
10225 */
10226 bnx2x_cl22_write(bp, phy, MDIO_PMA_REG_CTRL, 0x800);
10227 /*
10228 * This works with E3 only, no need to check the chip
10229 * before determining the port.
10230 */
10231 port = params->port;
10232 cfg_pin = (REG_RD(bp, params->shmem_base +
10233 offsetof(struct shmem_region,
10234 dev_info.port_hw_config[port].e3_cmn_pin_cfg)) &
10235 PORT_HW_CFG_E3_PHY_RESET_MASK) >>
10236 PORT_HW_CFG_E3_PHY_RESET_SHIFT;
10237
10238 /* Drive pin low to put GPHY in reset. */
10239 bnx2x_set_cfg_pin(bp, cfg_pin, 0);
10240 }
10241
10242 static u8 bnx2x_54618se_read_status(struct bnx2x_phy *phy,
10243 struct link_params *params,
10244 struct link_vars *vars)
10245 {
10246 struct bnx2x *bp = params->bp;
10247 u16 val;
10248 u8 link_up = 0;
10249 u16 legacy_status, legacy_speed;
10250
10251 /* Get speed operation status */
10252 bnx2x_cl22_read(bp, phy,
10253 0x19,
10254 &legacy_status);
10255 DP(NETIF_MSG_LINK, "54618SE read_status: 0x%x\n", legacy_status);
10256
10257 /* Read status to clear the PHY interrupt. */
10258 bnx2x_cl22_read(bp, phy,
10259 MDIO_REG_INTR_STATUS,
10260 &val);
10261
10262 link_up = ((legacy_status & (1<<2)) == (1<<2));
10263
10264 if (link_up) {
10265 legacy_speed = (legacy_status & (7<<8));
10266 if (legacy_speed == (7<<8)) {
10267 vars->line_speed = SPEED_1000;
10268 vars->duplex = DUPLEX_FULL;
10269 } else if (legacy_speed == (6<<8)) {
10270 vars->line_speed = SPEED_1000;
10271 vars->duplex = DUPLEX_HALF;
10272 } else if (legacy_speed == (5<<8)) {
10273 vars->line_speed = SPEED_100;
10274 vars->duplex = DUPLEX_FULL;
10275 }
10276 /* Omitting 100Base-T4 for now */
10277 else if (legacy_speed == (3<<8)) {
10278 vars->line_speed = SPEED_100;
10279 vars->duplex = DUPLEX_HALF;
10280 } else if (legacy_speed == (2<<8)) {
10281 vars->line_speed = SPEED_10;
10282 vars->duplex = DUPLEX_FULL;
10283 } else if (legacy_speed == (1<<8)) {
10284 vars->line_speed = SPEED_10;
10285 vars->duplex = DUPLEX_HALF;
10286 } else /* Should not happen */
10287 vars->line_speed = 0;
10288
10289 DP(NETIF_MSG_LINK, "Link is up in %dMbps,"
10290 " is_duplex_full= %d\n", vars->line_speed,
10291 (vars->duplex == DUPLEX_FULL));
10292
10293 /* Check legacy speed AN resolution */
10294 bnx2x_cl22_read(bp, phy,
10295 0x01,
10296 &val);
10297 if (val & (1<<5))
10298 vars->link_status |=
10299 LINK_STATUS_AUTO_NEGOTIATE_COMPLETE;
10300 bnx2x_cl22_read(bp, phy,
10301 0x06,
10302 &val);
10303 if ((val & (1<<0)) == 0)
10304 vars->link_status |=
10305 LINK_STATUS_PARALLEL_DETECTION_USED;
10306
10307 DP(NETIF_MSG_LINK, "BCM54618SE: link speed is %d\n",
10308 vars->line_speed);
10309
10310 /* Report whether EEE is resolved. */
10311 bnx2x_cl22_read(bp, phy, MDIO_REG_GPHY_PHYID_LSB, &val);
10312 if (val == MDIO_REG_GPHY_ID_54618SE) {
10313 if (vars->link_status &
10314 LINK_STATUS_AUTO_NEGOTIATE_COMPLETE)
10315 val = 0;
10316 else {
10317 bnx2x_cl22_write(bp, phy,
10318 MDIO_REG_GPHY_CL45_ADDR_REG,
10319 MDIO_AN_DEVAD);
10320 bnx2x_cl22_write(bp, phy,
10321 MDIO_REG_GPHY_CL45_DATA_REG,
10322 MDIO_REG_GPHY_EEE_RESOLVED);
10323 bnx2x_cl22_write(bp, phy,
10324 MDIO_REG_GPHY_CL45_ADDR_REG,
10325 (0x1 << 14) | MDIO_AN_DEVAD);
10326 bnx2x_cl22_read(bp, phy,
10327 MDIO_REG_GPHY_CL45_DATA_REG,
10328 &val);
10329 }
10330 DP(NETIF_MSG_LINK, "EEE resolution: 0x%x\n", val);
10331 }
10332
10333 bnx2x_ext_phy_resolve_fc(phy, params, vars);
10334 }
10335 return link_up;
10336 }
10337
10338 static void bnx2x_54618se_config_loopback(struct bnx2x_phy *phy,
10339 struct link_params *params)
10340 {
10341 struct bnx2x *bp = params->bp;
10342 u16 val;
10343 u32 umac_base = params->port ? GRCBASE_UMAC1 : GRCBASE_UMAC0;
10344
10345 DP(NETIF_MSG_LINK, "2PMA/PMD ext_phy_loopback: 54618se\n");
10346
10347 /* Enable master/slave manual mmode and set to master */
10348 /* mii write 9 [bits set 11 12] */
10349 bnx2x_cl22_write(bp, phy, 0x09, 3<<11);
10350
10351 /* forced 1G and disable autoneg */
10352 /* set val [mii read 0] */
10353 /* set val [expr $val & [bits clear 6 12 13]] */
10354 /* set val [expr $val | [bits set 6 8]] */
10355 /* mii write 0 $val */
10356 bnx2x_cl22_read(bp, phy, 0x00, &val);
10357 val &= ~((1<<6) | (1<<12) | (1<<13));
10358 val |= (1<<6) | (1<<8);
10359 bnx2x_cl22_write(bp, phy, 0x00, val);
10360
10361 /* Set external loopback and Tx using 6dB coding */
10362 /* mii write 0x18 7 */
10363 /* set val [mii read 0x18] */
10364 /* mii write 0x18 [expr $val | [bits set 10 15]] */
10365 bnx2x_cl22_write(bp, phy, 0x18, 7);
10366 bnx2x_cl22_read(bp, phy, 0x18, &val);
10367 bnx2x_cl22_write(bp, phy, 0x18, val | (1<<10) | (1<<15));
10368
10369 /* This register opens the gate for the UMAC despite its name */
10370 REG_WR(bp, NIG_REG_EGRESS_EMAC0_PORT + params->port*4, 1);
10371
10372 /*
10373 * Maximum Frame Length (RW). Defines a 14-Bit maximum frame
10374 * length used by the MAC receive logic to check frames.
10375 */
10376 REG_WR(bp, umac_base + UMAC_REG_MAXFR, 0x2710);
10377 }
10378
10379 /******************************************************************/
10380 /* SFX7101 PHY SECTION */
10381 /******************************************************************/
10382 static void bnx2x_7101_config_loopback(struct bnx2x_phy *phy,
10383 struct link_params *params)
10384 {
10385 struct bnx2x *bp = params->bp;
10386 /* SFX7101_XGXS_TEST1 */
10387 bnx2x_cl45_write(bp, phy,
10388 MDIO_XS_DEVAD, MDIO_XS_SFX7101_XGXS_TEST1, 0x100);
10389 }
10390
10391 static int bnx2x_7101_config_init(struct bnx2x_phy *phy,
10392 struct link_params *params,
10393 struct link_vars *vars)
10394 {
10395 u16 fw_ver1, fw_ver2, val;
10396 struct bnx2x *bp = params->bp;
10397 DP(NETIF_MSG_LINK, "Setting the SFX7101 LASI indication\n");
10398
10399 /* Restore normal power mode*/
10400 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
10401 MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port);
10402 /* HW reset */
10403 bnx2x_ext_phy_hw_reset(bp, params->port);
10404 bnx2x_wait_reset_complete(bp, phy, params);
10405
10406 bnx2x_cl45_write(bp, phy,
10407 MDIO_PMA_DEVAD, MDIO_PMA_LASI_CTRL, 0x1);
10408 DP(NETIF_MSG_LINK, "Setting the SFX7101 LED to blink on traffic\n");
10409 bnx2x_cl45_write(bp, phy,
10410 MDIO_PMA_DEVAD, MDIO_PMA_REG_7107_LED_CNTL, (1<<3));
10411
10412 bnx2x_ext_phy_set_pause(params, phy, vars);
10413 /* Restart autoneg */
10414 bnx2x_cl45_read(bp, phy,
10415 MDIO_AN_DEVAD, MDIO_AN_REG_CTRL, &val);
10416 val |= 0x200;
10417 bnx2x_cl45_write(bp, phy,
10418 MDIO_AN_DEVAD, MDIO_AN_REG_CTRL, val);
10419
10420 /* Save spirom version */
10421 bnx2x_cl45_read(bp, phy,
10422 MDIO_PMA_DEVAD, MDIO_PMA_REG_7101_VER1, &fw_ver1);
10423
10424 bnx2x_cl45_read(bp, phy,
10425 MDIO_PMA_DEVAD, MDIO_PMA_REG_7101_VER2, &fw_ver2);
10426 bnx2x_save_spirom_version(bp, params->port,
10427 (u32)(fw_ver1<<16 | fw_ver2), phy->ver_addr);
10428 return 0;
10429 }
10430
10431 static u8 bnx2x_7101_read_status(struct bnx2x_phy *phy,
10432 struct link_params *params,
10433 struct link_vars *vars)
10434 {
10435 struct bnx2x *bp = params->bp;
10436 u8 link_up;
10437 u16 val1, val2;
10438 bnx2x_cl45_read(bp, phy,
10439 MDIO_PMA_DEVAD, MDIO_PMA_LASI_STAT, &val2);
10440 bnx2x_cl45_read(bp, phy,
10441 MDIO_PMA_DEVAD, MDIO_PMA_LASI_STAT, &val1);
10442 DP(NETIF_MSG_LINK, "10G-base-T LASI status 0x%x->0x%x\n",
10443 val2, val1);
10444 bnx2x_cl45_read(bp, phy,
10445 MDIO_PMA_DEVAD, MDIO_PMA_REG_STATUS, &val2);
10446 bnx2x_cl45_read(bp, phy,
10447 MDIO_PMA_DEVAD, MDIO_PMA_REG_STATUS, &val1);
10448 DP(NETIF_MSG_LINK, "10G-base-T PMA status 0x%x->0x%x\n",
10449 val2, val1);
10450 link_up = ((val1 & 4) == 4);
10451 /* if link is up print the AN outcome of the SFX7101 PHY */
10452 if (link_up) {
10453 bnx2x_cl45_read(bp, phy,
10454 MDIO_AN_DEVAD, MDIO_AN_REG_MASTER_STATUS,
10455 &val2);
10456 vars->line_speed = SPEED_10000;
10457 vars->duplex = DUPLEX_FULL;
10458 DP(NETIF_MSG_LINK, "SFX7101 AN status 0x%x->Master=%x\n",
10459 val2, (val2 & (1<<14)));
10460 bnx2x_ext_phy_10G_an_resolve(bp, phy, vars);
10461 bnx2x_ext_phy_resolve_fc(phy, params, vars);
10462 }
10463 return link_up;
10464 }
10465
10466 static int bnx2x_7101_format_ver(u32 spirom_ver, u8 *str, u16 *len)
10467 {
10468 if (*len < 5)
10469 return -EINVAL;
10470 str[0] = (spirom_ver & 0xFF);
10471 str[1] = (spirom_ver & 0xFF00) >> 8;
10472 str[2] = (spirom_ver & 0xFF0000) >> 16;
10473 str[3] = (spirom_ver & 0xFF000000) >> 24;
10474 str[4] = '\0';
10475 *len -= 5;
10476 return 0;
10477 }
10478
10479 void bnx2x_sfx7101_sp_sw_reset(struct bnx2x *bp, struct bnx2x_phy *phy)
10480 {
10481 u16 val, cnt;
10482
10483 bnx2x_cl45_read(bp, phy,
10484 MDIO_PMA_DEVAD,
10485 MDIO_PMA_REG_7101_RESET, &val);
10486
10487 for (cnt = 0; cnt < 10; cnt++) {
10488 msleep(50);
10489 /* Writes a self-clearing reset */
10490 bnx2x_cl45_write(bp, phy,
10491 MDIO_PMA_DEVAD,
10492 MDIO_PMA_REG_7101_RESET,
10493 (val | (1<<15)));
10494 /* Wait for clear */
10495 bnx2x_cl45_read(bp, phy,
10496 MDIO_PMA_DEVAD,
10497 MDIO_PMA_REG_7101_RESET, &val);
10498
10499 if ((val & (1<<15)) == 0)
10500 break;
10501 }
10502 }
10503
10504 static void bnx2x_7101_hw_reset(struct bnx2x_phy *phy,
10505 struct link_params *params) {
10506 /* Low power mode is controlled by GPIO 2 */
10507 bnx2x_set_gpio(params->bp, MISC_REGISTERS_GPIO_2,
10508 MISC_REGISTERS_GPIO_OUTPUT_LOW, params->port);
10509 /* The PHY reset is controlled by GPIO 1 */
10510 bnx2x_set_gpio(params->bp, MISC_REGISTERS_GPIO_1,
10511 MISC_REGISTERS_GPIO_OUTPUT_LOW, params->port);
10512 }
10513
10514 static void bnx2x_7101_set_link_led(struct bnx2x_phy *phy,
10515 struct link_params *params, u8 mode)
10516 {
10517 u16 val = 0;
10518 struct bnx2x *bp = params->bp;
10519 switch (mode) {
10520 case LED_MODE_FRONT_PANEL_OFF:
10521 case LED_MODE_OFF:
10522 val = 2;
10523 break;
10524 case LED_MODE_ON:
10525 val = 1;
10526 break;
10527 case LED_MODE_OPER:
10528 val = 0;
10529 break;
10530 }
10531 bnx2x_cl45_write(bp, phy,
10532 MDIO_PMA_DEVAD,
10533 MDIO_PMA_REG_7107_LINK_LED_CNTL,
10534 val);
10535 }
10536
10537 /******************************************************************/
10538 /* STATIC PHY DECLARATION */
10539 /******************************************************************/
10540
10541 static struct bnx2x_phy phy_null = {
10542 .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_NOT_CONN,
10543 .addr = 0,
10544 .def_md_devad = 0,
10545 .flags = FLAGS_INIT_XGXS_FIRST,
10546 .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
10547 .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
10548 .mdio_ctrl = 0,
10549 .supported = 0,
10550 .media_type = ETH_PHY_NOT_PRESENT,
10551 .ver_addr = 0,
10552 .req_flow_ctrl = 0,
10553 .req_line_speed = 0,
10554 .speed_cap_mask = 0,
10555 .req_duplex = 0,
10556 .rsrv = 0,
10557 .config_init = (config_init_t)NULL,
10558 .read_status = (read_status_t)NULL,
10559 .link_reset = (link_reset_t)NULL,
10560 .config_loopback = (config_loopback_t)NULL,
10561 .format_fw_ver = (format_fw_ver_t)NULL,
10562 .hw_reset = (hw_reset_t)NULL,
10563 .set_link_led = (set_link_led_t)NULL,
10564 .phy_specific_func = (phy_specific_func_t)NULL
10565 };
10566
10567 static struct bnx2x_phy phy_serdes = {
10568 .type = PORT_HW_CFG_SERDES_EXT_PHY_TYPE_DIRECT,
10569 .addr = 0xff,
10570 .def_md_devad = 0,
10571 .flags = 0,
10572 .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
10573 .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
10574 .mdio_ctrl = 0,
10575 .supported = (SUPPORTED_10baseT_Half |
10576 SUPPORTED_10baseT_Full |
10577 SUPPORTED_100baseT_Half |
10578 SUPPORTED_100baseT_Full |
10579 SUPPORTED_1000baseT_Full |
10580 SUPPORTED_2500baseX_Full |
10581 SUPPORTED_TP |
10582 SUPPORTED_Autoneg |
10583 SUPPORTED_Pause |
10584 SUPPORTED_Asym_Pause),
10585 .media_type = ETH_PHY_BASE_T,
10586 .ver_addr = 0,
10587 .req_flow_ctrl = 0,
10588 .req_line_speed = 0,
10589 .speed_cap_mask = 0,
10590 .req_duplex = 0,
10591 .rsrv = 0,
10592 .config_init = (config_init_t)bnx2x_xgxs_config_init,
10593 .read_status = (read_status_t)bnx2x_link_settings_status,
10594 .link_reset = (link_reset_t)bnx2x_int_link_reset,
10595 .config_loopback = (config_loopback_t)NULL,
10596 .format_fw_ver = (format_fw_ver_t)NULL,
10597 .hw_reset = (hw_reset_t)NULL,
10598 .set_link_led = (set_link_led_t)NULL,
10599 .phy_specific_func = (phy_specific_func_t)NULL
10600 };
10601
10602 static struct bnx2x_phy phy_xgxs = {
10603 .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT,
10604 .addr = 0xff,
10605 .def_md_devad = 0,
10606 .flags = 0,
10607 .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
10608 .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
10609 .mdio_ctrl = 0,
10610 .supported = (SUPPORTED_10baseT_Half |
10611 SUPPORTED_10baseT_Full |
10612 SUPPORTED_100baseT_Half |
10613 SUPPORTED_100baseT_Full |
10614 SUPPORTED_1000baseT_Full |
10615 SUPPORTED_2500baseX_Full |
10616 SUPPORTED_10000baseT_Full |
10617 SUPPORTED_FIBRE |
10618 SUPPORTED_Autoneg |
10619 SUPPORTED_Pause |
10620 SUPPORTED_Asym_Pause),
10621 .media_type = ETH_PHY_CX4,
10622 .ver_addr = 0,
10623 .req_flow_ctrl = 0,
10624 .req_line_speed = 0,
10625 .speed_cap_mask = 0,
10626 .req_duplex = 0,
10627 .rsrv = 0,
10628 .config_init = (config_init_t)bnx2x_xgxs_config_init,
10629 .read_status = (read_status_t)bnx2x_link_settings_status,
10630 .link_reset = (link_reset_t)bnx2x_int_link_reset,
10631 .config_loopback = (config_loopback_t)bnx2x_set_xgxs_loopback,
10632 .format_fw_ver = (format_fw_ver_t)NULL,
10633 .hw_reset = (hw_reset_t)NULL,
10634 .set_link_led = (set_link_led_t)NULL,
10635 .phy_specific_func = (phy_specific_func_t)NULL
10636 };
10637 static struct bnx2x_phy phy_warpcore = {
10638 .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT,
10639 .addr = 0xff,
10640 .def_md_devad = 0,
10641 .flags = FLAGS_HW_LOCK_REQUIRED,
10642 .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
10643 .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
10644 .mdio_ctrl = 0,
10645 .supported = (SUPPORTED_10baseT_Half |
10646 SUPPORTED_10baseT_Full |
10647 SUPPORTED_100baseT_Half |
10648 SUPPORTED_100baseT_Full |
10649 SUPPORTED_1000baseT_Full |
10650 SUPPORTED_10000baseT_Full |
10651 SUPPORTED_20000baseKR2_Full |
10652 SUPPORTED_20000baseMLD2_Full |
10653 SUPPORTED_FIBRE |
10654 SUPPORTED_Autoneg |
10655 SUPPORTED_Pause |
10656 SUPPORTED_Asym_Pause),
10657 .media_type = ETH_PHY_UNSPECIFIED,
10658 .ver_addr = 0,
10659 .req_flow_ctrl = 0,
10660 .req_line_speed = 0,
10661 .speed_cap_mask = 0,
10662 /* req_duplex = */0,
10663 /* rsrv = */0,
10664 .config_init = (config_init_t)bnx2x_warpcore_config_init,
10665 .read_status = (read_status_t)bnx2x_warpcore_read_status,
10666 .link_reset = (link_reset_t)bnx2x_warpcore_link_reset,
10667 .config_loopback = (config_loopback_t)bnx2x_set_warpcore_loopback,
10668 .format_fw_ver = (format_fw_ver_t)NULL,
10669 .hw_reset = (hw_reset_t)bnx2x_warpcore_hw_reset,
10670 .set_link_led = (set_link_led_t)NULL,
10671 .phy_specific_func = (phy_specific_func_t)NULL
10672 };
10673
10674
10675 static struct bnx2x_phy phy_7101 = {
10676 .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101,
10677 .addr = 0xff,
10678 .def_md_devad = 0,
10679 .flags = FLAGS_FAN_FAILURE_DET_REQ,
10680 .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
10681 .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
10682 .mdio_ctrl = 0,
10683 .supported = (SUPPORTED_10000baseT_Full |
10684 SUPPORTED_TP |
10685 SUPPORTED_Autoneg |
10686 SUPPORTED_Pause |
10687 SUPPORTED_Asym_Pause),
10688 .media_type = ETH_PHY_BASE_T,
10689 .ver_addr = 0,
10690 .req_flow_ctrl = 0,
10691 .req_line_speed = 0,
10692 .speed_cap_mask = 0,
10693 .req_duplex = 0,
10694 .rsrv = 0,
10695 .config_init = (config_init_t)bnx2x_7101_config_init,
10696 .read_status = (read_status_t)bnx2x_7101_read_status,
10697 .link_reset = (link_reset_t)bnx2x_common_ext_link_reset,
10698 .config_loopback = (config_loopback_t)bnx2x_7101_config_loopback,
10699 .format_fw_ver = (format_fw_ver_t)bnx2x_7101_format_ver,
10700 .hw_reset = (hw_reset_t)bnx2x_7101_hw_reset,
10701 .set_link_led = (set_link_led_t)bnx2x_7101_set_link_led,
10702 .phy_specific_func = (phy_specific_func_t)NULL
10703 };
10704 static struct bnx2x_phy phy_8073 = {
10705 .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073,
10706 .addr = 0xff,
10707 .def_md_devad = 0,
10708 .flags = FLAGS_HW_LOCK_REQUIRED,
10709 .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
10710 .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
10711 .mdio_ctrl = 0,
10712 .supported = (SUPPORTED_10000baseT_Full |
10713 SUPPORTED_2500baseX_Full |
10714 SUPPORTED_1000baseT_Full |
10715 SUPPORTED_FIBRE |
10716 SUPPORTED_Autoneg |
10717 SUPPORTED_Pause |
10718 SUPPORTED_Asym_Pause),
10719 .media_type = ETH_PHY_KR,
10720 .ver_addr = 0,
10721 .req_flow_ctrl = 0,
10722 .req_line_speed = 0,
10723 .speed_cap_mask = 0,
10724 .req_duplex = 0,
10725 .rsrv = 0,
10726 .config_init = (config_init_t)bnx2x_8073_config_init,
10727 .read_status = (read_status_t)bnx2x_8073_read_status,
10728 .link_reset = (link_reset_t)bnx2x_8073_link_reset,
10729 .config_loopback = (config_loopback_t)NULL,
10730 .format_fw_ver = (format_fw_ver_t)bnx2x_format_ver,
10731 .hw_reset = (hw_reset_t)NULL,
10732 .set_link_led = (set_link_led_t)NULL,
10733 .phy_specific_func = (phy_specific_func_t)NULL
10734 };
10735 static struct bnx2x_phy phy_8705 = {
10736 .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705,
10737 .addr = 0xff,
10738 .def_md_devad = 0,
10739 .flags = FLAGS_INIT_XGXS_FIRST,
10740 .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
10741 .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
10742 .mdio_ctrl = 0,
10743 .supported = (SUPPORTED_10000baseT_Full |
10744 SUPPORTED_FIBRE |
10745 SUPPORTED_Pause |
10746 SUPPORTED_Asym_Pause),
10747 .media_type = ETH_PHY_XFP_FIBER,
10748 .ver_addr = 0,
10749 .req_flow_ctrl = 0,
10750 .req_line_speed = 0,
10751 .speed_cap_mask = 0,
10752 .req_duplex = 0,
10753 .rsrv = 0,
10754 .config_init = (config_init_t)bnx2x_8705_config_init,
10755 .read_status = (read_status_t)bnx2x_8705_read_status,
10756 .link_reset = (link_reset_t)bnx2x_common_ext_link_reset,
10757 .config_loopback = (config_loopback_t)NULL,
10758 .format_fw_ver = (format_fw_ver_t)bnx2x_null_format_ver,
10759 .hw_reset = (hw_reset_t)NULL,
10760 .set_link_led = (set_link_led_t)NULL,
10761 .phy_specific_func = (phy_specific_func_t)NULL
10762 };
10763 static struct bnx2x_phy phy_8706 = {
10764 .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706,
10765 .addr = 0xff,
10766 .def_md_devad = 0,
10767 .flags = FLAGS_INIT_XGXS_FIRST,
10768 .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
10769 .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
10770 .mdio_ctrl = 0,
10771 .supported = (SUPPORTED_10000baseT_Full |
10772 SUPPORTED_1000baseT_Full |
10773 SUPPORTED_FIBRE |
10774 SUPPORTED_Pause |
10775 SUPPORTED_Asym_Pause),
10776 .media_type = ETH_PHY_SFP_FIBER,
10777 .ver_addr = 0,
10778 .req_flow_ctrl = 0,
10779 .req_line_speed = 0,
10780 .speed_cap_mask = 0,
10781 .req_duplex = 0,
10782 .rsrv = 0,
10783 .config_init = (config_init_t)bnx2x_8706_config_init,
10784 .read_status = (read_status_t)bnx2x_8706_read_status,
10785 .link_reset = (link_reset_t)bnx2x_common_ext_link_reset,
10786 .config_loopback = (config_loopback_t)NULL,
10787 .format_fw_ver = (format_fw_ver_t)bnx2x_format_ver,
10788 .hw_reset = (hw_reset_t)NULL,
10789 .set_link_led = (set_link_led_t)NULL,
10790 .phy_specific_func = (phy_specific_func_t)NULL
10791 };
10792
10793 static struct bnx2x_phy phy_8726 = {
10794 .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726,
10795 .addr = 0xff,
10796 .def_md_devad = 0,
10797 .flags = (FLAGS_HW_LOCK_REQUIRED |
10798 FLAGS_INIT_XGXS_FIRST),
10799 .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
10800 .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
10801 .mdio_ctrl = 0,
10802 .supported = (SUPPORTED_10000baseT_Full |
10803 SUPPORTED_1000baseT_Full |
10804 SUPPORTED_Autoneg |
10805 SUPPORTED_FIBRE |
10806 SUPPORTED_Pause |
10807 SUPPORTED_Asym_Pause),
10808 .media_type = ETH_PHY_NOT_PRESENT,
10809 .ver_addr = 0,
10810 .req_flow_ctrl = 0,
10811 .req_line_speed = 0,
10812 .speed_cap_mask = 0,
10813 .req_duplex = 0,
10814 .rsrv = 0,
10815 .config_init = (config_init_t)bnx2x_8726_config_init,
10816 .read_status = (read_status_t)bnx2x_8726_read_status,
10817 .link_reset = (link_reset_t)bnx2x_8726_link_reset,
10818 .config_loopback = (config_loopback_t)bnx2x_8726_config_loopback,
10819 .format_fw_ver = (format_fw_ver_t)bnx2x_format_ver,
10820 .hw_reset = (hw_reset_t)NULL,
10821 .set_link_led = (set_link_led_t)NULL,
10822 .phy_specific_func = (phy_specific_func_t)NULL
10823 };
10824
10825 static struct bnx2x_phy phy_8727 = {
10826 .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727,
10827 .addr = 0xff,
10828 .def_md_devad = 0,
10829 .flags = FLAGS_FAN_FAILURE_DET_REQ,
10830 .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
10831 .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
10832 .mdio_ctrl = 0,
10833 .supported = (SUPPORTED_10000baseT_Full |
10834 SUPPORTED_1000baseT_Full |
10835 SUPPORTED_FIBRE |
10836 SUPPORTED_Pause |
10837 SUPPORTED_Asym_Pause),
10838 .media_type = ETH_PHY_NOT_PRESENT,
10839 .ver_addr = 0,
10840 .req_flow_ctrl = 0,
10841 .req_line_speed = 0,
10842 .speed_cap_mask = 0,
10843 .req_duplex = 0,
10844 .rsrv = 0,
10845 .config_init = (config_init_t)bnx2x_8727_config_init,
10846 .read_status = (read_status_t)bnx2x_8727_read_status,
10847 .link_reset = (link_reset_t)bnx2x_8727_link_reset,
10848 .config_loopback = (config_loopback_t)NULL,
10849 .format_fw_ver = (format_fw_ver_t)bnx2x_format_ver,
10850 .hw_reset = (hw_reset_t)bnx2x_8727_hw_reset,
10851 .set_link_led = (set_link_led_t)bnx2x_8727_set_link_led,
10852 .phy_specific_func = (phy_specific_func_t)bnx2x_8727_specific_func
10853 };
10854 static struct bnx2x_phy phy_8481 = {
10855 .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481,
10856 .addr = 0xff,
10857 .def_md_devad = 0,
10858 .flags = FLAGS_FAN_FAILURE_DET_REQ |
10859 FLAGS_REARM_LATCH_SIGNAL,
10860 .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
10861 .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
10862 .mdio_ctrl = 0,
10863 .supported = (SUPPORTED_10baseT_Half |
10864 SUPPORTED_10baseT_Full |
10865 SUPPORTED_100baseT_Half |
10866 SUPPORTED_100baseT_Full |
10867 SUPPORTED_1000baseT_Full |
10868 SUPPORTED_10000baseT_Full |
10869 SUPPORTED_TP |
10870 SUPPORTED_Autoneg |
10871 SUPPORTED_Pause |
10872 SUPPORTED_Asym_Pause),
10873 .media_type = ETH_PHY_BASE_T,
10874 .ver_addr = 0,
10875 .req_flow_ctrl = 0,
10876 .req_line_speed = 0,
10877 .speed_cap_mask = 0,
10878 .req_duplex = 0,
10879 .rsrv = 0,
10880 .config_init = (config_init_t)bnx2x_8481_config_init,
10881 .read_status = (read_status_t)bnx2x_848xx_read_status,
10882 .link_reset = (link_reset_t)bnx2x_8481_link_reset,
10883 .config_loopback = (config_loopback_t)NULL,
10884 .format_fw_ver = (format_fw_ver_t)bnx2x_848xx_format_ver,
10885 .hw_reset = (hw_reset_t)bnx2x_8481_hw_reset,
10886 .set_link_led = (set_link_led_t)bnx2x_848xx_set_link_led,
10887 .phy_specific_func = (phy_specific_func_t)NULL
10888 };
10889
10890 static struct bnx2x_phy phy_84823 = {
10891 .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823,
10892 .addr = 0xff,
10893 .def_md_devad = 0,
10894 .flags = FLAGS_FAN_FAILURE_DET_REQ |
10895 FLAGS_REARM_LATCH_SIGNAL,
10896 .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
10897 .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
10898 .mdio_ctrl = 0,
10899 .supported = (SUPPORTED_10baseT_Half |
10900 SUPPORTED_10baseT_Full |
10901 SUPPORTED_100baseT_Half |
10902 SUPPORTED_100baseT_Full |
10903 SUPPORTED_1000baseT_Full |
10904 SUPPORTED_10000baseT_Full |
10905 SUPPORTED_TP |
10906 SUPPORTED_Autoneg |
10907 SUPPORTED_Pause |
10908 SUPPORTED_Asym_Pause),
10909 .media_type = ETH_PHY_BASE_T,
10910 .ver_addr = 0,
10911 .req_flow_ctrl = 0,
10912 .req_line_speed = 0,
10913 .speed_cap_mask = 0,
10914 .req_duplex = 0,
10915 .rsrv = 0,
10916 .config_init = (config_init_t)bnx2x_848x3_config_init,
10917 .read_status = (read_status_t)bnx2x_848xx_read_status,
10918 .link_reset = (link_reset_t)bnx2x_848x3_link_reset,
10919 .config_loopback = (config_loopback_t)NULL,
10920 .format_fw_ver = (format_fw_ver_t)bnx2x_848xx_format_ver,
10921 .hw_reset = (hw_reset_t)NULL,
10922 .set_link_led = (set_link_led_t)bnx2x_848xx_set_link_led,
10923 .phy_specific_func = (phy_specific_func_t)NULL
10924 };
10925
10926 static struct bnx2x_phy phy_84833 = {
10927 .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833,
10928 .addr = 0xff,
10929 .def_md_devad = 0,
10930 .flags = FLAGS_FAN_FAILURE_DET_REQ |
10931 FLAGS_REARM_LATCH_SIGNAL,
10932 .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
10933 .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
10934 .mdio_ctrl = 0,
10935 .supported = (SUPPORTED_100baseT_Half |
10936 SUPPORTED_100baseT_Full |
10937 SUPPORTED_1000baseT_Full |
10938 SUPPORTED_10000baseT_Full |
10939 SUPPORTED_TP |
10940 SUPPORTED_Autoneg |
10941 SUPPORTED_Pause |
10942 SUPPORTED_Asym_Pause),
10943 .media_type = ETH_PHY_BASE_T,
10944 .ver_addr = 0,
10945 .req_flow_ctrl = 0,
10946 .req_line_speed = 0,
10947 .speed_cap_mask = 0,
10948 .req_duplex = 0,
10949 .rsrv = 0,
10950 .config_init = (config_init_t)bnx2x_848x3_config_init,
10951 .read_status = (read_status_t)bnx2x_848xx_read_status,
10952 .link_reset = (link_reset_t)bnx2x_848x3_link_reset,
10953 .config_loopback = (config_loopback_t)NULL,
10954 .format_fw_ver = (format_fw_ver_t)bnx2x_848xx_format_ver,
10955 .hw_reset = (hw_reset_t)bnx2x_84833_hw_reset_phy,
10956 .set_link_led = (set_link_led_t)bnx2x_848xx_set_link_led,
10957 .phy_specific_func = (phy_specific_func_t)NULL
10958 };
10959
10960 static struct bnx2x_phy phy_54618se = {
10961 .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM54618SE,
10962 .addr = 0xff,
10963 .def_md_devad = 0,
10964 .flags = FLAGS_INIT_XGXS_FIRST,
10965 .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
10966 .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
10967 .mdio_ctrl = 0,
10968 .supported = (SUPPORTED_10baseT_Half |
10969 SUPPORTED_10baseT_Full |
10970 SUPPORTED_100baseT_Half |
10971 SUPPORTED_100baseT_Full |
10972 SUPPORTED_1000baseT_Full |
10973 SUPPORTED_TP |
10974 SUPPORTED_Autoneg |
10975 SUPPORTED_Pause |
10976 SUPPORTED_Asym_Pause),
10977 .media_type = ETH_PHY_BASE_T,
10978 .ver_addr = 0,
10979 .req_flow_ctrl = 0,
10980 .req_line_speed = 0,
10981 .speed_cap_mask = 0,
10982 /* req_duplex = */0,
10983 /* rsrv = */0,
10984 .config_init = (config_init_t)bnx2x_54618se_config_init,
10985 .read_status = (read_status_t)bnx2x_54618se_read_status,
10986 .link_reset = (link_reset_t)bnx2x_54618se_link_reset,
10987 .config_loopback = (config_loopback_t)bnx2x_54618se_config_loopback,
10988 .format_fw_ver = (format_fw_ver_t)NULL,
10989 .hw_reset = (hw_reset_t)NULL,
10990 .set_link_led = (set_link_led_t)bnx2x_54618se_set_link_led,
10991 .phy_specific_func = (phy_specific_func_t)NULL
10992 };
10993 /*****************************************************************/
10994 /* */
10995 /* Populate the phy according. Main function: bnx2x_populate_phy */
10996 /* */
10997 /*****************************************************************/
10998
10999 static void bnx2x_populate_preemphasis(struct bnx2x *bp, u32 shmem_base,
11000 struct bnx2x_phy *phy, u8 port,
11001 u8 phy_index)
11002 {
11003 /* Get the 4 lanes xgxs config rx and tx */
11004 u32 rx = 0, tx = 0, i;
11005 for (i = 0; i < 2; i++) {
11006 /*
11007 * INT_PHY and EXT_PHY1 share the same value location in the
11008 * shmem. When num_phys is greater than 1, than this value
11009 * applies only to EXT_PHY1
11010 */
11011 if (phy_index == INT_PHY || phy_index == EXT_PHY1) {
11012 rx = REG_RD(bp, shmem_base +
11013 offsetof(struct shmem_region,
11014 dev_info.port_hw_config[port].xgxs_config_rx[i<<1]));
11015
11016 tx = REG_RD(bp, shmem_base +
11017 offsetof(struct shmem_region,
11018 dev_info.port_hw_config[port].xgxs_config_tx[i<<1]));
11019 } else {
11020 rx = REG_RD(bp, shmem_base +
11021 offsetof(struct shmem_region,
11022 dev_info.port_hw_config[port].xgxs_config2_rx[i<<1]));
11023
11024 tx = REG_RD(bp, shmem_base +
11025 offsetof(struct shmem_region,
11026 dev_info.port_hw_config[port].xgxs_config2_rx[i<<1]));
11027 }
11028
11029 phy->rx_preemphasis[i << 1] = ((rx>>16) & 0xffff);
11030 phy->rx_preemphasis[(i << 1) + 1] = (rx & 0xffff);
11031
11032 phy->tx_preemphasis[i << 1] = ((tx>>16) & 0xffff);
11033 phy->tx_preemphasis[(i << 1) + 1] = (tx & 0xffff);
11034 }
11035 }
11036
11037 static u32 bnx2x_get_ext_phy_config(struct bnx2x *bp, u32 shmem_base,
11038 u8 phy_index, u8 port)
11039 {
11040 u32 ext_phy_config = 0;
11041 switch (phy_index) {
11042 case EXT_PHY1:
11043 ext_phy_config = REG_RD(bp, shmem_base +
11044 offsetof(struct shmem_region,
11045 dev_info.port_hw_config[port].external_phy_config));
11046 break;
11047 case EXT_PHY2:
11048 ext_phy_config = REG_RD(bp, shmem_base +
11049 offsetof(struct shmem_region,
11050 dev_info.port_hw_config[port].external_phy_config2));
11051 break;
11052 default:
11053 DP(NETIF_MSG_LINK, "Invalid phy_index %d\n", phy_index);
11054 return -EINVAL;
11055 }
11056
11057 return ext_phy_config;
11058 }
11059 static int bnx2x_populate_int_phy(struct bnx2x *bp, u32 shmem_base, u8 port,
11060 struct bnx2x_phy *phy)
11061 {
11062 u32 phy_addr;
11063 u32 chip_id;
11064 u32 switch_cfg = (REG_RD(bp, shmem_base +
11065 offsetof(struct shmem_region,
11066 dev_info.port_feature_config[port].link_config)) &
11067 PORT_FEATURE_CONNECTED_SWITCH_MASK);
11068 chip_id = REG_RD(bp, MISC_REG_CHIP_NUM) << 16;
11069 DP(NETIF_MSG_LINK, ":chip_id = 0x%x\n", chip_id);
11070 if (USES_WARPCORE(bp)) {
11071 u32 serdes_net_if;
11072 phy_addr = REG_RD(bp,
11073 MISC_REG_WC0_CTRL_PHY_ADDR);
11074 *phy = phy_warpcore;
11075 if (REG_RD(bp, MISC_REG_PORT4MODE_EN_OVWR) == 0x3)
11076 phy->flags |= FLAGS_4_PORT_MODE;
11077 else
11078 phy->flags &= ~FLAGS_4_PORT_MODE;
11079 /* Check Dual mode */
11080 serdes_net_if = (REG_RD(bp, shmem_base +
11081 offsetof(struct shmem_region, dev_info.
11082 port_hw_config[port].default_cfg)) &
11083 PORT_HW_CFG_NET_SERDES_IF_MASK);
11084 /*
11085 * Set the appropriate supported and flags indications per
11086 * interface type of the chip
11087 */
11088 switch (serdes_net_if) {
11089 case PORT_HW_CFG_NET_SERDES_IF_SGMII:
11090 phy->supported &= (SUPPORTED_10baseT_Half |
11091 SUPPORTED_10baseT_Full |
11092 SUPPORTED_100baseT_Half |
11093 SUPPORTED_100baseT_Full |
11094 SUPPORTED_1000baseT_Full |
11095 SUPPORTED_FIBRE |
11096 SUPPORTED_Autoneg |
11097 SUPPORTED_Pause |
11098 SUPPORTED_Asym_Pause);
11099 phy->media_type = ETH_PHY_BASE_T;
11100 break;
11101 case PORT_HW_CFG_NET_SERDES_IF_XFI:
11102 phy->media_type = ETH_PHY_XFP_FIBER;
11103 break;
11104 case PORT_HW_CFG_NET_SERDES_IF_SFI:
11105 phy->supported &= (SUPPORTED_1000baseT_Full |
11106 SUPPORTED_10000baseT_Full |
11107 SUPPORTED_FIBRE |
11108 SUPPORTED_Pause |
11109 SUPPORTED_Asym_Pause);
11110 phy->media_type = ETH_PHY_SFP_FIBER;
11111 break;
11112 case PORT_HW_CFG_NET_SERDES_IF_KR:
11113 phy->media_type = ETH_PHY_KR;
11114 phy->supported &= (SUPPORTED_1000baseT_Full |
11115 SUPPORTED_10000baseT_Full |
11116 SUPPORTED_FIBRE |
11117 SUPPORTED_Autoneg |
11118 SUPPORTED_Pause |
11119 SUPPORTED_Asym_Pause);
11120 break;
11121 case PORT_HW_CFG_NET_SERDES_IF_DXGXS:
11122 phy->media_type = ETH_PHY_KR;
11123 phy->flags |= FLAGS_WC_DUAL_MODE;
11124 phy->supported &= (SUPPORTED_20000baseMLD2_Full |
11125 SUPPORTED_FIBRE |
11126 SUPPORTED_Pause |
11127 SUPPORTED_Asym_Pause);
11128 break;
11129 case PORT_HW_CFG_NET_SERDES_IF_KR2:
11130 phy->media_type = ETH_PHY_KR;
11131 phy->flags |= FLAGS_WC_DUAL_MODE;
11132 phy->supported &= (SUPPORTED_20000baseKR2_Full |
11133 SUPPORTED_FIBRE |
11134 SUPPORTED_Pause |
11135 SUPPORTED_Asym_Pause);
11136 break;
11137 default:
11138 DP(NETIF_MSG_LINK, "Unknown WC interface type 0x%x\n",
11139 serdes_net_if);
11140 break;
11141 }
11142
11143 /*
11144 * Enable MDC/MDIO work-around for E3 A0 since free running MDC
11145 * was not set as expected. For B0, ECO will be enabled so there
11146 * won't be an issue there
11147 */
11148 if (CHIP_REV(bp) == CHIP_REV_Ax)
11149 phy->flags |= FLAGS_MDC_MDIO_WA;
11150 else
11151 phy->flags |= FLAGS_MDC_MDIO_WA_B0;
11152 } else {
11153 switch (switch_cfg) {
11154 case SWITCH_CFG_1G:
11155 phy_addr = REG_RD(bp,
11156 NIG_REG_SERDES0_CTRL_PHY_ADDR +
11157 port * 0x10);
11158 *phy = phy_serdes;
11159 break;
11160 case SWITCH_CFG_10G:
11161 phy_addr = REG_RD(bp,
11162 NIG_REG_XGXS0_CTRL_PHY_ADDR +
11163 port * 0x18);
11164 *phy = phy_xgxs;
11165 break;
11166 default:
11167 DP(NETIF_MSG_LINK, "Invalid switch_cfg\n");
11168 return -EINVAL;
11169 }
11170 }
11171 phy->addr = (u8)phy_addr;
11172 phy->mdio_ctrl = bnx2x_get_emac_base(bp,
11173 SHARED_HW_CFG_MDC_MDIO_ACCESS1_BOTH,
11174 port);
11175 if (CHIP_IS_E2(bp))
11176 phy->def_md_devad = E2_DEFAULT_PHY_DEV_ADDR;
11177 else
11178 phy->def_md_devad = DEFAULT_PHY_DEV_ADDR;
11179
11180 DP(NETIF_MSG_LINK, "Internal phy port=%d, addr=0x%x, mdio_ctl=0x%x\n",
11181 port, phy->addr, phy->mdio_ctrl);
11182
11183 bnx2x_populate_preemphasis(bp, shmem_base, phy, port, INT_PHY);
11184 return 0;
11185 }
11186
11187 static int bnx2x_populate_ext_phy(struct bnx2x *bp,
11188 u8 phy_index,
11189 u32 shmem_base,
11190 u32 shmem2_base,
11191 u8 port,
11192 struct bnx2x_phy *phy)
11193 {
11194 u32 ext_phy_config, phy_type, config2;
11195 u32 mdc_mdio_access = SHARED_HW_CFG_MDC_MDIO_ACCESS1_BOTH;
11196 ext_phy_config = bnx2x_get_ext_phy_config(bp, shmem_base,
11197 phy_index, port);
11198 phy_type = XGXS_EXT_PHY_TYPE(ext_phy_config);
11199 /* Select the phy type */
11200 switch (phy_type) {
11201 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073:
11202 mdc_mdio_access = SHARED_HW_CFG_MDC_MDIO_ACCESS1_SWAPPED;
11203 *phy = phy_8073;
11204 break;
11205 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705:
11206 *phy = phy_8705;
11207 break;
11208 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706:
11209 *phy = phy_8706;
11210 break;
11211 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726:
11212 mdc_mdio_access = SHARED_HW_CFG_MDC_MDIO_ACCESS1_EMAC1;
11213 *phy = phy_8726;
11214 break;
11215 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727_NOC:
11216 /* BCM8727_NOC => BCM8727 no over current */
11217 mdc_mdio_access = SHARED_HW_CFG_MDC_MDIO_ACCESS1_EMAC1;
11218 *phy = phy_8727;
11219 phy->flags |= FLAGS_NOC;
11220 break;
11221 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8722:
11222 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
11223 mdc_mdio_access = SHARED_HW_CFG_MDC_MDIO_ACCESS1_EMAC1;
11224 *phy = phy_8727;
11225 break;
11226 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481:
11227 *phy = phy_8481;
11228 break;
11229 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823:
11230 *phy = phy_84823;
11231 break;
11232 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833:
11233 *phy = phy_84833;
11234 break;
11235 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM54618SE:
11236 *phy = phy_54618se;
11237 break;
11238 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101:
11239 *phy = phy_7101;
11240 break;
11241 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE:
11242 *phy = phy_null;
11243 return -EINVAL;
11244 default:
11245 *phy = phy_null;
11246 return 0;
11247 }
11248
11249 phy->addr = XGXS_EXT_PHY_ADDR(ext_phy_config);
11250 bnx2x_populate_preemphasis(bp, shmem_base, phy, port, phy_index);
11251
11252 /*
11253 * The shmem address of the phy version is located on different
11254 * structures. In case this structure is too old, do not set
11255 * the address
11256 */
11257 config2 = REG_RD(bp, shmem_base + offsetof(struct shmem_region,
11258 dev_info.shared_hw_config.config2));
11259 if (phy_index == EXT_PHY1) {
11260 phy->ver_addr = shmem_base + offsetof(struct shmem_region,
11261 port_mb[port].ext_phy_fw_version);
11262
11263 /* Check specific mdc mdio settings */
11264 if (config2 & SHARED_HW_CFG_MDC_MDIO_ACCESS1_MASK)
11265 mdc_mdio_access = config2 &
11266 SHARED_HW_CFG_MDC_MDIO_ACCESS1_MASK;
11267 } else {
11268 u32 size = REG_RD(bp, shmem2_base);
11269
11270 if (size >
11271 offsetof(struct shmem2_region, ext_phy_fw_version2)) {
11272 phy->ver_addr = shmem2_base +
11273 offsetof(struct shmem2_region,
11274 ext_phy_fw_version2[port]);
11275 }
11276 /* Check specific mdc mdio settings */
11277 if (config2 & SHARED_HW_CFG_MDC_MDIO_ACCESS2_MASK)
11278 mdc_mdio_access = (config2 &
11279 SHARED_HW_CFG_MDC_MDIO_ACCESS2_MASK) >>
11280 (SHARED_HW_CFG_MDC_MDIO_ACCESS2_SHIFT -
11281 SHARED_HW_CFG_MDC_MDIO_ACCESS1_SHIFT);
11282 }
11283 phy->mdio_ctrl = bnx2x_get_emac_base(bp, mdc_mdio_access, port);
11284
11285 /*
11286 * In case mdc/mdio_access of the external phy is different than the
11287 * mdc/mdio access of the XGXS, a HW lock must be taken in each access
11288 * to prevent one port interfere with another port's CL45 operations.
11289 */
11290 if (mdc_mdio_access != SHARED_HW_CFG_MDC_MDIO_ACCESS1_BOTH)
11291 phy->flags |= FLAGS_HW_LOCK_REQUIRED;
11292 DP(NETIF_MSG_LINK, "phy_type 0x%x port %d found in index %d\n",
11293 phy_type, port, phy_index);
11294 DP(NETIF_MSG_LINK, " addr=0x%x, mdio_ctl=0x%x\n",
11295 phy->addr, phy->mdio_ctrl);
11296 return 0;
11297 }
11298
11299 static int bnx2x_populate_phy(struct bnx2x *bp, u8 phy_index, u32 shmem_base,
11300 u32 shmem2_base, u8 port, struct bnx2x_phy *phy)
11301 {
11302 int status = 0;
11303 phy->type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_NOT_CONN;
11304 if (phy_index == INT_PHY)
11305 return bnx2x_populate_int_phy(bp, shmem_base, port, phy);
11306 status = bnx2x_populate_ext_phy(bp, phy_index, shmem_base, shmem2_base,
11307 port, phy);
11308 return status;
11309 }
11310
11311 static void bnx2x_phy_def_cfg(struct link_params *params,
11312 struct bnx2x_phy *phy,
11313 u8 phy_index)
11314 {
11315 struct bnx2x *bp = params->bp;
11316 u32 link_config;
11317 /* Populate the default phy configuration for MF mode */
11318 if (phy_index == EXT_PHY2) {
11319 link_config = REG_RD(bp, params->shmem_base +
11320 offsetof(struct shmem_region, dev_info.
11321 port_feature_config[params->port].link_config2));
11322 phy->speed_cap_mask = REG_RD(bp, params->shmem_base +
11323 offsetof(struct shmem_region,
11324 dev_info.
11325 port_hw_config[params->port].speed_capability_mask2));
11326 } else {
11327 link_config = REG_RD(bp, params->shmem_base +
11328 offsetof(struct shmem_region, dev_info.
11329 port_feature_config[params->port].link_config));
11330 phy->speed_cap_mask = REG_RD(bp, params->shmem_base +
11331 offsetof(struct shmem_region,
11332 dev_info.
11333 port_hw_config[params->port].speed_capability_mask));
11334 }
11335 DP(NETIF_MSG_LINK, "Default config phy idx %x cfg 0x%x speed_cap_mask"
11336 " 0x%x\n", phy_index, link_config, phy->speed_cap_mask);
11337
11338 phy->req_duplex = DUPLEX_FULL;
11339 switch (link_config & PORT_FEATURE_LINK_SPEED_MASK) {
11340 case PORT_FEATURE_LINK_SPEED_10M_HALF:
11341 phy->req_duplex = DUPLEX_HALF;
11342 case PORT_FEATURE_LINK_SPEED_10M_FULL:
11343 phy->req_line_speed = SPEED_10;
11344 break;
11345 case PORT_FEATURE_LINK_SPEED_100M_HALF:
11346 phy->req_duplex = DUPLEX_HALF;
11347 case PORT_FEATURE_LINK_SPEED_100M_FULL:
11348 phy->req_line_speed = SPEED_100;
11349 break;
11350 case PORT_FEATURE_LINK_SPEED_1G:
11351 phy->req_line_speed = SPEED_1000;
11352 break;
11353 case PORT_FEATURE_LINK_SPEED_2_5G:
11354 phy->req_line_speed = SPEED_2500;
11355 break;
11356 case PORT_FEATURE_LINK_SPEED_10G_CX4:
11357 phy->req_line_speed = SPEED_10000;
11358 break;
11359 default:
11360 phy->req_line_speed = SPEED_AUTO_NEG;
11361 break;
11362 }
11363
11364 switch (link_config & PORT_FEATURE_FLOW_CONTROL_MASK) {
11365 case PORT_FEATURE_FLOW_CONTROL_AUTO:
11366 phy->req_flow_ctrl = BNX2X_FLOW_CTRL_AUTO;
11367 break;
11368 case PORT_FEATURE_FLOW_CONTROL_TX:
11369 phy->req_flow_ctrl = BNX2X_FLOW_CTRL_TX;
11370 break;
11371 case PORT_FEATURE_FLOW_CONTROL_RX:
11372 phy->req_flow_ctrl = BNX2X_FLOW_CTRL_RX;
11373 break;
11374 case PORT_FEATURE_FLOW_CONTROL_BOTH:
11375 phy->req_flow_ctrl = BNX2X_FLOW_CTRL_BOTH;
11376 break;
11377 default:
11378 phy->req_flow_ctrl = BNX2X_FLOW_CTRL_NONE;
11379 break;
11380 }
11381 }
11382
11383 u32 bnx2x_phy_selection(struct link_params *params)
11384 {
11385 u32 phy_config_swapped, prio_cfg;
11386 u32 return_cfg = PORT_HW_CFG_PHY_SELECTION_HARDWARE_DEFAULT;
11387
11388 phy_config_swapped = params->multi_phy_config &
11389 PORT_HW_CFG_PHY_SWAPPED_ENABLED;
11390
11391 prio_cfg = params->multi_phy_config &
11392 PORT_HW_CFG_PHY_SELECTION_MASK;
11393
11394 if (phy_config_swapped) {
11395 switch (prio_cfg) {
11396 case PORT_HW_CFG_PHY_SELECTION_FIRST_PHY_PRIORITY:
11397 return_cfg = PORT_HW_CFG_PHY_SELECTION_SECOND_PHY_PRIORITY;
11398 break;
11399 case PORT_HW_CFG_PHY_SELECTION_SECOND_PHY_PRIORITY:
11400 return_cfg = PORT_HW_CFG_PHY_SELECTION_FIRST_PHY_PRIORITY;
11401 break;
11402 case PORT_HW_CFG_PHY_SELECTION_SECOND_PHY:
11403 return_cfg = PORT_HW_CFG_PHY_SELECTION_FIRST_PHY;
11404 break;
11405 case PORT_HW_CFG_PHY_SELECTION_FIRST_PHY:
11406 return_cfg = PORT_HW_CFG_PHY_SELECTION_SECOND_PHY;
11407 break;
11408 }
11409 } else
11410 return_cfg = prio_cfg;
11411
11412 return return_cfg;
11413 }
11414
11415
11416 int bnx2x_phy_probe(struct link_params *params)
11417 {
11418 u8 phy_index, actual_phy_idx, link_cfg_idx;
11419 u32 phy_config_swapped, sync_offset, media_types;
11420 struct bnx2x *bp = params->bp;
11421 struct bnx2x_phy *phy;
11422 params->num_phys = 0;
11423 DP(NETIF_MSG_LINK, "Begin phy probe\n");
11424 phy_config_swapped = params->multi_phy_config &
11425 PORT_HW_CFG_PHY_SWAPPED_ENABLED;
11426
11427 for (phy_index = INT_PHY; phy_index < MAX_PHYS;
11428 phy_index++) {
11429 link_cfg_idx = LINK_CONFIG_IDX(phy_index);
11430 actual_phy_idx = phy_index;
11431 if (phy_config_swapped) {
11432 if (phy_index == EXT_PHY1)
11433 actual_phy_idx = EXT_PHY2;
11434 else if (phy_index == EXT_PHY2)
11435 actual_phy_idx = EXT_PHY1;
11436 }
11437 DP(NETIF_MSG_LINK, "phy_config_swapped %x, phy_index %x,"
11438 " actual_phy_idx %x\n", phy_config_swapped,
11439 phy_index, actual_phy_idx);
11440 phy = &params->phy[actual_phy_idx];
11441 if (bnx2x_populate_phy(bp, phy_index, params->shmem_base,
11442 params->shmem2_base, params->port,
11443 phy) != 0) {
11444 params->num_phys = 0;
11445 DP(NETIF_MSG_LINK, "phy probe failed in phy index %d\n",
11446 phy_index);
11447 for (phy_index = INT_PHY;
11448 phy_index < MAX_PHYS;
11449 phy_index++)
11450 *phy = phy_null;
11451 return -EINVAL;
11452 }
11453 if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_NOT_CONN)
11454 break;
11455
11456 sync_offset = params->shmem_base +
11457 offsetof(struct shmem_region,
11458 dev_info.port_hw_config[params->port].media_type);
11459 media_types = REG_RD(bp, sync_offset);
11460
11461 /*
11462 * Update media type for non-PMF sync only for the first time
11463 * In case the media type changes afterwards, it will be updated
11464 * using the update_status function
11465 */
11466 if ((media_types & (PORT_HW_CFG_MEDIA_TYPE_PHY0_MASK <<
11467 (PORT_HW_CFG_MEDIA_TYPE_PHY1_SHIFT *
11468 actual_phy_idx))) == 0) {
11469 media_types |= ((phy->media_type &
11470 PORT_HW_CFG_MEDIA_TYPE_PHY0_MASK) <<
11471 (PORT_HW_CFG_MEDIA_TYPE_PHY1_SHIFT *
11472 actual_phy_idx));
11473 }
11474 REG_WR(bp, sync_offset, media_types);
11475
11476 bnx2x_phy_def_cfg(params, phy, phy_index);
11477 params->num_phys++;
11478 }
11479
11480 DP(NETIF_MSG_LINK, "End phy probe. #phys found %x\n", params->num_phys);
11481 return 0;
11482 }
11483
11484 void bnx2x_init_bmac_loopback(struct link_params *params,
11485 struct link_vars *vars)
11486 {
11487 struct bnx2x *bp = params->bp;
11488 vars->link_up = 1;
11489 vars->line_speed = SPEED_10000;
11490 vars->duplex = DUPLEX_FULL;
11491 vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;
11492 vars->mac_type = MAC_TYPE_BMAC;
11493
11494 vars->phy_flags = PHY_XGXS_FLAG;
11495
11496 bnx2x_xgxs_deassert(params);
11497
11498 /* set bmac loopback */
11499 bnx2x_bmac_enable(params, vars, 1);
11500
11501 REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 0);
11502 }
11503
11504 void bnx2x_init_emac_loopback(struct link_params *params,
11505 struct link_vars *vars)
11506 {
11507 struct bnx2x *bp = params->bp;
11508 vars->link_up = 1;
11509 vars->line_speed = SPEED_1000;
11510 vars->duplex = DUPLEX_FULL;
11511 vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;
11512 vars->mac_type = MAC_TYPE_EMAC;
11513
11514 vars->phy_flags = PHY_XGXS_FLAG;
11515
11516 bnx2x_xgxs_deassert(params);
11517 /* set bmac loopback */
11518 bnx2x_emac_enable(params, vars, 1);
11519 bnx2x_emac_program(params, vars);
11520 REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 0);
11521 }
11522
11523 void bnx2x_init_xmac_loopback(struct link_params *params,
11524 struct link_vars *vars)
11525 {
11526 struct bnx2x *bp = params->bp;
11527 vars->link_up = 1;
11528 if (!params->req_line_speed[0])
11529 vars->line_speed = SPEED_10000;
11530 else
11531 vars->line_speed = params->req_line_speed[0];
11532 vars->duplex = DUPLEX_FULL;
11533 vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;
11534 vars->mac_type = MAC_TYPE_XMAC;
11535 vars->phy_flags = PHY_XGXS_FLAG;
11536 /*
11537 * Set WC to loopback mode since link is required to provide clock
11538 * to the XMAC in 20G mode
11539 */
11540 bnx2x_set_aer_mmd(params, &params->phy[0]);
11541 bnx2x_warpcore_reset_lane(bp, &params->phy[0], 0);
11542 params->phy[INT_PHY].config_loopback(
11543 &params->phy[INT_PHY],
11544 params);
11545
11546 bnx2x_xmac_enable(params, vars, 1);
11547 REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 0);
11548 }
11549
11550 void bnx2x_init_umac_loopback(struct link_params *params,
11551 struct link_vars *vars)
11552 {
11553 struct bnx2x *bp = params->bp;
11554 vars->link_up = 1;
11555 vars->line_speed = SPEED_1000;
11556 vars->duplex = DUPLEX_FULL;
11557 vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;
11558 vars->mac_type = MAC_TYPE_UMAC;
11559 vars->phy_flags = PHY_XGXS_FLAG;
11560 bnx2x_umac_enable(params, vars, 1);
11561
11562 REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 0);
11563 }
11564
11565 void bnx2x_init_xgxs_loopback(struct link_params *params,
11566 struct link_vars *vars)
11567 {
11568 struct bnx2x *bp = params->bp;
11569 vars->link_up = 1;
11570 vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;
11571 vars->duplex = DUPLEX_FULL;
11572 if (params->req_line_speed[0] == SPEED_1000)
11573 vars->line_speed = SPEED_1000;
11574 else
11575 vars->line_speed = SPEED_10000;
11576
11577 if (!USES_WARPCORE(bp))
11578 bnx2x_xgxs_deassert(params);
11579 bnx2x_link_initialize(params, vars);
11580
11581 if (params->req_line_speed[0] == SPEED_1000) {
11582 if (USES_WARPCORE(bp))
11583 bnx2x_umac_enable(params, vars, 0);
11584 else {
11585 bnx2x_emac_program(params, vars);
11586 bnx2x_emac_enable(params, vars, 0);
11587 }
11588 } else {
11589 if (USES_WARPCORE(bp))
11590 bnx2x_xmac_enable(params, vars, 0);
11591 else
11592 bnx2x_bmac_enable(params, vars, 0);
11593 }
11594
11595 if (params->loopback_mode == LOOPBACK_XGXS) {
11596 /* set 10G XGXS loopback */
11597 params->phy[INT_PHY].config_loopback(
11598 &params->phy[INT_PHY],
11599 params);
11600
11601 } else {
11602 /* set external phy loopback */
11603 u8 phy_index;
11604 for (phy_index = EXT_PHY1;
11605 phy_index < params->num_phys; phy_index++) {
11606 if (params->phy[phy_index].config_loopback)
11607 params->phy[phy_index].config_loopback(
11608 &params->phy[phy_index],
11609 params);
11610 }
11611 }
11612 REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 0);
11613
11614 bnx2x_set_led(params, vars, LED_MODE_OPER, vars->line_speed);
11615 }
11616
11617 int bnx2x_phy_init(struct link_params *params, struct link_vars *vars)
11618 {
11619 struct bnx2x *bp = params->bp;
11620 DP(NETIF_MSG_LINK, "Phy Initialization started\n");
11621 DP(NETIF_MSG_LINK, "(1) req_speed %d, req_flowctrl %d\n",
11622 params->req_line_speed[0], params->req_flow_ctrl[0]);
11623 DP(NETIF_MSG_LINK, "(2) req_speed %d, req_flowctrl %d\n",
11624 params->req_line_speed[1], params->req_flow_ctrl[1]);
11625 vars->link_status = 0;
11626 vars->phy_link_up = 0;
11627 vars->link_up = 0;
11628 vars->line_speed = 0;
11629 vars->duplex = DUPLEX_FULL;
11630 vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;
11631 vars->mac_type = MAC_TYPE_NONE;
11632 vars->phy_flags = 0;
11633
11634 /* disable attentions */
11635 bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 + params->port*4,
11636 (NIG_MASK_XGXS0_LINK_STATUS |
11637 NIG_MASK_XGXS0_LINK10G |
11638 NIG_MASK_SERDES0_LINK_STATUS |
11639 NIG_MASK_MI_INT));
11640
11641 bnx2x_emac_init(params, vars);
11642
11643 if (params->num_phys == 0) {
11644 DP(NETIF_MSG_LINK, "No phy found for initialization !!\n");
11645 return -EINVAL;
11646 }
11647 set_phy_vars(params, vars);
11648
11649 DP(NETIF_MSG_LINK, "Num of phys on board: %d\n", params->num_phys);
11650 switch (params->loopback_mode) {
11651 case LOOPBACK_BMAC:
11652 bnx2x_init_bmac_loopback(params, vars);
11653 break;
11654 case LOOPBACK_EMAC:
11655 bnx2x_init_emac_loopback(params, vars);
11656 break;
11657 case LOOPBACK_XMAC:
11658 bnx2x_init_xmac_loopback(params, vars);
11659 break;
11660 case LOOPBACK_UMAC:
11661 bnx2x_init_umac_loopback(params, vars);
11662 break;
11663 case LOOPBACK_XGXS:
11664 case LOOPBACK_EXT_PHY:
11665 bnx2x_init_xgxs_loopback(params, vars);
11666 break;
11667 default:
11668 if (!CHIP_IS_E3(bp)) {
11669 if (params->switch_cfg == SWITCH_CFG_10G)
11670 bnx2x_xgxs_deassert(params);
11671 else
11672 bnx2x_serdes_deassert(bp, params->port);
11673 }
11674 bnx2x_link_initialize(params, vars);
11675 msleep(30);
11676 bnx2x_link_int_enable(params);
11677 break;
11678 }
11679 return 0;
11680 }
11681
11682 int bnx2x_link_reset(struct link_params *params, struct link_vars *vars,
11683 u8 reset_ext_phy)
11684 {
11685 struct bnx2x *bp = params->bp;
11686 u8 phy_index, port = params->port, clear_latch_ind = 0;
11687 DP(NETIF_MSG_LINK, "Resetting the link of port %d\n", port);
11688 /* disable attentions */
11689 vars->link_status = 0;
11690 bnx2x_update_mng(params, vars->link_status);
11691 bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port*4,
11692 (NIG_MASK_XGXS0_LINK_STATUS |
11693 NIG_MASK_XGXS0_LINK10G |
11694 NIG_MASK_SERDES0_LINK_STATUS |
11695 NIG_MASK_MI_INT));
11696
11697 /* activate nig drain */
11698 REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + port*4, 1);
11699
11700 /* disable nig egress interface */
11701 if (!CHIP_IS_E3(bp)) {
11702 REG_WR(bp, NIG_REG_BMAC0_OUT_EN + port*4, 0);
11703 REG_WR(bp, NIG_REG_EGRESS_EMAC0_OUT_EN + port*4, 0);
11704 }
11705
11706 /* Stop BigMac rx */
11707 if (!CHIP_IS_E3(bp))
11708 bnx2x_bmac_rx_disable(bp, port);
11709 else
11710 bnx2x_xmac_disable(params);
11711 /* disable emac */
11712 if (!CHIP_IS_E3(bp))
11713 REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 0);
11714
11715 msleep(10);
11716 /* The PHY reset is controlled by GPIO 1
11717 * Hold it as vars low
11718 */
11719 /* clear link led */
11720 bnx2x_set_led(params, vars, LED_MODE_OFF, 0);
11721
11722 if (reset_ext_phy) {
11723 bnx2x_set_mdio_clk(bp, params->chip_id, port);
11724 for (phy_index = EXT_PHY1; phy_index < params->num_phys;
11725 phy_index++) {
11726 if (params->phy[phy_index].link_reset) {
11727 bnx2x_set_aer_mmd(params,
11728 &params->phy[phy_index]);
11729 params->phy[phy_index].link_reset(
11730 &params->phy[phy_index],
11731 params);
11732 }
11733 if (params->phy[phy_index].flags &
11734 FLAGS_REARM_LATCH_SIGNAL)
11735 clear_latch_ind = 1;
11736 }
11737 }
11738
11739 if (clear_latch_ind) {
11740 /* Clear latching indication */
11741 bnx2x_rearm_latch_signal(bp, port, 0);
11742 bnx2x_bits_dis(bp, NIG_REG_LATCH_BC_0 + port*4,
11743 1 << NIG_LATCH_BC_ENABLE_MI_INT);
11744 }
11745 if (params->phy[INT_PHY].link_reset)
11746 params->phy[INT_PHY].link_reset(
11747 &params->phy[INT_PHY], params);
11748 /* reset BigMac */
11749 REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR,
11750 (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
11751
11752 /* disable nig ingress interface */
11753 if (!CHIP_IS_E3(bp)) {
11754 REG_WR(bp, NIG_REG_BMAC0_IN_EN + port*4, 0);
11755 REG_WR(bp, NIG_REG_EMAC0_IN_EN + port*4, 0);
11756 }
11757 vars->link_up = 0;
11758 vars->phy_flags = 0;
11759 return 0;
11760 }
11761
11762 /****************************************************************************/
11763 /* Common function */
11764 /****************************************************************************/
11765 static int bnx2x_8073_common_init_phy(struct bnx2x *bp,
11766 u32 shmem_base_path[],
11767 u32 shmem2_base_path[], u8 phy_index,
11768 u32 chip_id)
11769 {
11770 struct bnx2x_phy phy[PORT_MAX];
11771 struct bnx2x_phy *phy_blk[PORT_MAX];
11772 u16 val;
11773 s8 port = 0;
11774 s8 port_of_path = 0;
11775 u32 swap_val, swap_override;
11776 swap_val = REG_RD(bp, NIG_REG_PORT_SWAP);
11777 swap_override = REG_RD(bp, NIG_REG_STRAP_OVERRIDE);
11778 port ^= (swap_val && swap_override);
11779 bnx2x_ext_phy_hw_reset(bp, port);
11780 /* PART1 - Reset both phys */
11781 for (port = PORT_MAX - 1; port >= PORT_0; port--) {
11782 u32 shmem_base, shmem2_base;
11783 /* In E2, same phy is using for port0 of the two paths */
11784 if (CHIP_IS_E1x(bp)) {
11785 shmem_base = shmem_base_path[0];
11786 shmem2_base = shmem2_base_path[0];
11787 port_of_path = port;
11788 } else {
11789 shmem_base = shmem_base_path[port];
11790 shmem2_base = shmem2_base_path[port];
11791 port_of_path = 0;
11792 }
11793
11794 /* Extract the ext phy address for the port */
11795 if (bnx2x_populate_phy(bp, phy_index, shmem_base, shmem2_base,
11796 port_of_path, &phy[port]) !=
11797 0) {
11798 DP(NETIF_MSG_LINK, "populate_phy failed\n");
11799 return -EINVAL;
11800 }
11801 /* disable attentions */
11802 bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 +
11803 port_of_path*4,
11804 (NIG_MASK_XGXS0_LINK_STATUS |
11805 NIG_MASK_XGXS0_LINK10G |
11806 NIG_MASK_SERDES0_LINK_STATUS |
11807 NIG_MASK_MI_INT));
11808
11809 /* Need to take the phy out of low power mode in order
11810 to write to access its registers */
11811 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
11812 MISC_REGISTERS_GPIO_OUTPUT_HIGH,
11813 port);
11814
11815 /* Reset the phy */
11816 bnx2x_cl45_write(bp, &phy[port],
11817 MDIO_PMA_DEVAD,
11818 MDIO_PMA_REG_CTRL,
11819 1<<15);
11820 }
11821
11822 /* Add delay of 150ms after reset */
11823 msleep(150);
11824
11825 if (phy[PORT_0].addr & 0x1) {
11826 phy_blk[PORT_0] = &(phy[PORT_1]);
11827 phy_blk[PORT_1] = &(phy[PORT_0]);
11828 } else {
11829 phy_blk[PORT_0] = &(phy[PORT_0]);
11830 phy_blk[PORT_1] = &(phy[PORT_1]);
11831 }
11832
11833 /* PART2 - Download firmware to both phys */
11834 for (port = PORT_MAX - 1; port >= PORT_0; port--) {
11835 if (CHIP_IS_E1x(bp))
11836 port_of_path = port;
11837 else
11838 port_of_path = 0;
11839
11840 DP(NETIF_MSG_LINK, "Loading spirom for phy address 0x%x\n",
11841 phy_blk[port]->addr);
11842 if (bnx2x_8073_8727_external_rom_boot(bp, phy_blk[port],
11843 port_of_path))
11844 return -EINVAL;
11845
11846 /* Only set bit 10 = 1 (Tx power down) */
11847 bnx2x_cl45_read(bp, phy_blk[port],
11848 MDIO_PMA_DEVAD,
11849 MDIO_PMA_REG_TX_POWER_DOWN, &val);
11850
11851 /* Phase1 of TX_POWER_DOWN reset */
11852 bnx2x_cl45_write(bp, phy_blk[port],
11853 MDIO_PMA_DEVAD,
11854 MDIO_PMA_REG_TX_POWER_DOWN,
11855 (val | 1<<10));
11856 }
11857
11858 /*
11859 * Toggle Transmitter: Power down and then up with 600ms delay
11860 * between
11861 */
11862 msleep(600);
11863
11864 /* PART3 - complete TX_POWER_DOWN process, and set GPIO2 back to low */
11865 for (port = PORT_MAX - 1; port >= PORT_0; port--) {
11866 /* Phase2 of POWER_DOWN_RESET */
11867 /* Release bit 10 (Release Tx power down) */
11868 bnx2x_cl45_read(bp, phy_blk[port],
11869 MDIO_PMA_DEVAD,
11870 MDIO_PMA_REG_TX_POWER_DOWN, &val);
11871
11872 bnx2x_cl45_write(bp, phy_blk[port],
11873 MDIO_PMA_DEVAD,
11874 MDIO_PMA_REG_TX_POWER_DOWN, (val & (~(1<<10))));
11875 msleep(15);
11876
11877 /* Read modify write the SPI-ROM version select register */
11878 bnx2x_cl45_read(bp, phy_blk[port],
11879 MDIO_PMA_DEVAD,
11880 MDIO_PMA_REG_EDC_FFE_MAIN, &val);
11881 bnx2x_cl45_write(bp, phy_blk[port],
11882 MDIO_PMA_DEVAD,
11883 MDIO_PMA_REG_EDC_FFE_MAIN, (val | (1<<12)));
11884
11885 /* set GPIO2 back to LOW */
11886 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
11887 MISC_REGISTERS_GPIO_OUTPUT_LOW, port);
11888 }
11889 return 0;
11890 }
11891 static int bnx2x_8726_common_init_phy(struct bnx2x *bp,
11892 u32 shmem_base_path[],
11893 u32 shmem2_base_path[], u8 phy_index,
11894 u32 chip_id)
11895 {
11896 u32 val;
11897 s8 port;
11898 struct bnx2x_phy phy;
11899 /* Use port1 because of the static port-swap */
11900 /* Enable the module detection interrupt */
11901 val = REG_RD(bp, MISC_REG_GPIO_EVENT_EN);
11902 val |= ((1<<MISC_REGISTERS_GPIO_3)|
11903 (1<<(MISC_REGISTERS_GPIO_3 + MISC_REGISTERS_GPIO_PORT_SHIFT)));
11904 REG_WR(bp, MISC_REG_GPIO_EVENT_EN, val);
11905
11906 bnx2x_ext_phy_hw_reset(bp, 0);
11907 msleep(5);
11908 for (port = 0; port < PORT_MAX; port++) {
11909 u32 shmem_base, shmem2_base;
11910
11911 /* In E2, same phy is using for port0 of the two paths */
11912 if (CHIP_IS_E1x(bp)) {
11913 shmem_base = shmem_base_path[0];
11914 shmem2_base = shmem2_base_path[0];
11915 } else {
11916 shmem_base = shmem_base_path[port];
11917 shmem2_base = shmem2_base_path[port];
11918 }
11919 /* Extract the ext phy address for the port */
11920 if (bnx2x_populate_phy(bp, phy_index, shmem_base, shmem2_base,
11921 port, &phy) !=
11922 0) {
11923 DP(NETIF_MSG_LINK, "populate phy failed\n");
11924 return -EINVAL;
11925 }
11926
11927 /* Reset phy*/
11928 bnx2x_cl45_write(bp, &phy,
11929 MDIO_PMA_DEVAD, MDIO_PMA_REG_GEN_CTRL, 0x0001);
11930
11931
11932 /* Set fault module detected LED on */
11933 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_0,
11934 MISC_REGISTERS_GPIO_HIGH,
11935 port);
11936 }
11937
11938 return 0;
11939 }
11940 static void bnx2x_get_ext_phy_reset_gpio(struct bnx2x *bp, u32 shmem_base,
11941 u8 *io_gpio, u8 *io_port)
11942 {
11943
11944 u32 phy_gpio_reset = REG_RD(bp, shmem_base +
11945 offsetof(struct shmem_region,
11946 dev_info.port_hw_config[PORT_0].default_cfg));
11947 switch (phy_gpio_reset) {
11948 case PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO0_P0:
11949 *io_gpio = 0;
11950 *io_port = 0;
11951 break;
11952 case PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO1_P0:
11953 *io_gpio = 1;
11954 *io_port = 0;
11955 break;
11956 case PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO2_P0:
11957 *io_gpio = 2;
11958 *io_port = 0;
11959 break;
11960 case PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO3_P0:
11961 *io_gpio = 3;
11962 *io_port = 0;
11963 break;
11964 case PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO0_P1:
11965 *io_gpio = 0;
11966 *io_port = 1;
11967 break;
11968 case PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO1_P1:
11969 *io_gpio = 1;
11970 *io_port = 1;
11971 break;
11972 case PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO2_P1:
11973 *io_gpio = 2;
11974 *io_port = 1;
11975 break;
11976 case PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO3_P1:
11977 *io_gpio = 3;
11978 *io_port = 1;
11979 break;
11980 default:
11981 /* Don't override the io_gpio and io_port */
11982 break;
11983 }
11984 }
11985
11986 static int bnx2x_8727_common_init_phy(struct bnx2x *bp,
11987 u32 shmem_base_path[],
11988 u32 shmem2_base_path[], u8 phy_index,
11989 u32 chip_id)
11990 {
11991 s8 port, reset_gpio;
11992 u32 swap_val, swap_override;
11993 struct bnx2x_phy phy[PORT_MAX];
11994 struct bnx2x_phy *phy_blk[PORT_MAX];
11995 s8 port_of_path;
11996 swap_val = REG_RD(bp, NIG_REG_PORT_SWAP);
11997 swap_override = REG_RD(bp, NIG_REG_STRAP_OVERRIDE);
11998
11999 reset_gpio = MISC_REGISTERS_GPIO_1;
12000 port = 1;
12001
12002 /*
12003 * Retrieve the reset gpio/port which control the reset.
12004 * Default is GPIO1, PORT1
12005 */
12006 bnx2x_get_ext_phy_reset_gpio(bp, shmem_base_path[0],
12007 (u8 *)&reset_gpio, (u8 *)&port);
12008
12009 /* Calculate the port based on port swap */
12010 port ^= (swap_val && swap_override);
12011
12012 /* Initiate PHY reset*/
12013 bnx2x_set_gpio(bp, reset_gpio, MISC_REGISTERS_GPIO_OUTPUT_LOW,
12014 port);
12015 msleep(1);
12016 bnx2x_set_gpio(bp, reset_gpio, MISC_REGISTERS_GPIO_OUTPUT_HIGH,
12017 port);
12018
12019 msleep(5);
12020
12021 /* PART1 - Reset both phys */
12022 for (port = PORT_MAX - 1; port >= PORT_0; port--) {
12023 u32 shmem_base, shmem2_base;
12024
12025 /* In E2, same phy is using for port0 of the two paths */
12026 if (CHIP_IS_E1x(bp)) {
12027 shmem_base = shmem_base_path[0];
12028 shmem2_base = shmem2_base_path[0];
12029 port_of_path = port;
12030 } else {
12031 shmem_base = shmem_base_path[port];
12032 shmem2_base = shmem2_base_path[port];
12033 port_of_path = 0;
12034 }
12035
12036 /* Extract the ext phy address for the port */
12037 if (bnx2x_populate_phy(bp, phy_index, shmem_base, shmem2_base,
12038 port_of_path, &phy[port]) !=
12039 0) {
12040 DP(NETIF_MSG_LINK, "populate phy failed\n");
12041 return -EINVAL;
12042 }
12043 /* disable attentions */
12044 bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 +
12045 port_of_path*4,
12046 (NIG_MASK_XGXS0_LINK_STATUS |
12047 NIG_MASK_XGXS0_LINK10G |
12048 NIG_MASK_SERDES0_LINK_STATUS |
12049 NIG_MASK_MI_INT));
12050
12051
12052 /* Reset the phy */
12053 bnx2x_cl45_write(bp, &phy[port],
12054 MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 1<<15);
12055 }
12056
12057 /* Add delay of 150ms after reset */
12058 msleep(150);
12059 if (phy[PORT_0].addr & 0x1) {
12060 phy_blk[PORT_0] = &(phy[PORT_1]);
12061 phy_blk[PORT_1] = &(phy[PORT_0]);
12062 } else {
12063 phy_blk[PORT_0] = &(phy[PORT_0]);
12064 phy_blk[PORT_1] = &(phy[PORT_1]);
12065 }
12066 /* PART2 - Download firmware to both phys */
12067 for (port = PORT_MAX - 1; port >= PORT_0; port--) {
12068 if (CHIP_IS_E1x(bp))
12069 port_of_path = port;
12070 else
12071 port_of_path = 0;
12072 DP(NETIF_MSG_LINK, "Loading spirom for phy address 0x%x\n",
12073 phy_blk[port]->addr);
12074 if (bnx2x_8073_8727_external_rom_boot(bp, phy_blk[port],
12075 port_of_path))
12076 return -EINVAL;
12077 /* Disable PHY transmitter output */
12078 bnx2x_cl45_write(bp, phy_blk[port],
12079 MDIO_PMA_DEVAD,
12080 MDIO_PMA_REG_TX_DISABLE, 1);
12081
12082 }
12083 return 0;
12084 }
12085
12086 static int bnx2x_ext_phy_common_init(struct bnx2x *bp, u32 shmem_base_path[],
12087 u32 shmem2_base_path[], u8 phy_index,
12088 u32 ext_phy_type, u32 chip_id)
12089 {
12090 int rc = 0;
12091
12092 switch (ext_phy_type) {
12093 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073:
12094 rc = bnx2x_8073_common_init_phy(bp, shmem_base_path,
12095 shmem2_base_path,
12096 phy_index, chip_id);
12097 break;
12098 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8722:
12099 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
12100 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727_NOC:
12101 rc = bnx2x_8727_common_init_phy(bp, shmem_base_path,
12102 shmem2_base_path,
12103 phy_index, chip_id);
12104 break;
12105
12106 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726:
12107 /*
12108 * GPIO1 affects both ports, so there's need to pull
12109 * it for single port alone
12110 */
12111 rc = bnx2x_8726_common_init_phy(bp, shmem_base_path,
12112 shmem2_base_path,
12113 phy_index, chip_id);
12114 break;
12115 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833:
12116 /*
12117 * GPIO3's are linked, and so both need to be toggled
12118 * to obtain required 2us pulse.
12119 */
12120 rc = bnx2x_84833_common_init_phy(bp, shmem_base_path, chip_id);
12121 break;
12122 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE:
12123 rc = -EINVAL;
12124 break;
12125 default:
12126 DP(NETIF_MSG_LINK,
12127 "ext_phy 0x%x common init not required\n",
12128 ext_phy_type);
12129 break;
12130 }
12131
12132 if (rc != 0)
12133 netdev_err(bp->dev, "Warning: PHY was not initialized,"
12134 " Port %d\n",
12135 0);
12136 return rc;
12137 }
12138
12139 int bnx2x_common_init_phy(struct bnx2x *bp, u32 shmem_base_path[],
12140 u32 shmem2_base_path[], u32 chip_id)
12141 {
12142 int rc = 0;
12143 u32 phy_ver, val;
12144 u8 phy_index = 0;
12145 u32 ext_phy_type, ext_phy_config;
12146 bnx2x_set_mdio_clk(bp, chip_id, PORT_0);
12147 bnx2x_set_mdio_clk(bp, chip_id, PORT_1);
12148 DP(NETIF_MSG_LINK, "Begin common phy init\n");
12149 if (CHIP_IS_E3(bp)) {
12150 /* Enable EPIO */
12151 val = REG_RD(bp, MISC_REG_GEN_PURP_HWG);
12152 REG_WR(bp, MISC_REG_GEN_PURP_HWG, val | 1);
12153 }
12154 /* Check if common init was already done */
12155 phy_ver = REG_RD(bp, shmem_base_path[0] +
12156 offsetof(struct shmem_region,
12157 port_mb[PORT_0].ext_phy_fw_version));
12158 if (phy_ver) {
12159 DP(NETIF_MSG_LINK, "Not doing common init; phy ver is 0x%x\n",
12160 phy_ver);
12161 return 0;
12162 }
12163
12164 /* Read the ext_phy_type for arbitrary port(0) */
12165 for (phy_index = EXT_PHY1; phy_index < MAX_PHYS;
12166 phy_index++) {
12167 ext_phy_config = bnx2x_get_ext_phy_config(bp,
12168 shmem_base_path[0],
12169 phy_index, 0);
12170 ext_phy_type = XGXS_EXT_PHY_TYPE(ext_phy_config);
12171 rc |= bnx2x_ext_phy_common_init(bp, shmem_base_path,
12172 shmem2_base_path,
12173 phy_index, ext_phy_type,
12174 chip_id);
12175 }
12176 return rc;
12177 }
12178
12179 static void bnx2x_check_over_curr(struct link_params *params,
12180 struct link_vars *vars)
12181 {
12182 struct bnx2x *bp = params->bp;
12183 u32 cfg_pin;
12184 u8 port = params->port;
12185 u32 pin_val;
12186
12187 cfg_pin = (REG_RD(bp, params->shmem_base +
12188 offsetof(struct shmem_region,
12189 dev_info.port_hw_config[port].e3_cmn_pin_cfg1)) &
12190 PORT_HW_CFG_E3_OVER_CURRENT_MASK) >>
12191 PORT_HW_CFG_E3_OVER_CURRENT_SHIFT;
12192
12193 /* Ignore check if no external input PIN available */
12194 if (bnx2x_get_cfg_pin(bp, cfg_pin, &pin_val) != 0)
12195 return;
12196
12197 if (!pin_val) {
12198 if ((vars->phy_flags & PHY_OVER_CURRENT_FLAG) == 0) {
12199 netdev_err(bp->dev, "Error: Power fault on Port %d has"
12200 " been detected and the power to "
12201 "that SFP+ module has been removed"
12202 " to prevent failure of the card."
12203 " Please remove the SFP+ module and"
12204 " restart the system to clear this"
12205 " error.\n",
12206 params->port);
12207 vars->phy_flags |= PHY_OVER_CURRENT_FLAG;
12208 }
12209 } else
12210 vars->phy_flags &= ~PHY_OVER_CURRENT_FLAG;
12211 }
12212
12213 static void bnx2x_analyze_link_error(struct link_params *params,
12214 struct link_vars *vars, u32 lss_status)
12215 {
12216 struct bnx2x *bp = params->bp;
12217 /* Compare new value with previous value */
12218 u8 led_mode;
12219 u32 half_open_conn = (vars->phy_flags & PHY_HALF_OPEN_CONN_FLAG) > 0;
12220
12221 if ((lss_status ^ half_open_conn) == 0)
12222 return;
12223
12224 /* If values differ */
12225 DP(NETIF_MSG_LINK, "Link changed:%x %x->%x\n", vars->link_up,
12226 half_open_conn, lss_status);
12227
12228 /*
12229 * a. Update shmem->link_status accordingly
12230 * b. Update link_vars->link_up
12231 */
12232 if (lss_status) {
12233 DP(NETIF_MSG_LINK, "Remote Fault detected !!!\n");
12234 vars->link_status &= ~LINK_STATUS_LINK_UP;
12235 vars->link_up = 0;
12236 vars->phy_flags |= PHY_HALF_OPEN_CONN_FLAG;
12237 /*
12238 * Set LED mode to off since the PHY doesn't know about these
12239 * errors
12240 */
12241 led_mode = LED_MODE_OFF;
12242 } else {
12243 DP(NETIF_MSG_LINK, "Remote Fault cleared\n");
12244 vars->link_status |= LINK_STATUS_LINK_UP;
12245 vars->link_up = 1;
12246 vars->phy_flags &= ~PHY_HALF_OPEN_CONN_FLAG;
12247 led_mode = LED_MODE_OPER;
12248 }
12249 /* Update the LED according to the link state */
12250 bnx2x_set_led(params, vars, led_mode, SPEED_10000);
12251
12252 /* Update link status in the shared memory */
12253 bnx2x_update_mng(params, vars->link_status);
12254
12255 /* C. Trigger General Attention */
12256 vars->periodic_flags |= PERIODIC_FLAGS_LINK_EVENT;
12257 bnx2x_notify_link_changed(bp);
12258 }
12259
12260 /******************************************************************************
12261 * Description:
12262 * This function checks for half opened connection change indication.
12263 * When such change occurs, it calls the bnx2x_analyze_link_error
12264 * to check if Remote Fault is set or cleared. Reception of remote fault
12265 * status message in the MAC indicates that the peer's MAC has detected
12266 * a fault, for example, due to break in the TX side of fiber.
12267 *
12268 ******************************************************************************/
12269 static void bnx2x_check_half_open_conn(struct link_params *params,
12270 struct link_vars *vars)
12271 {
12272 struct bnx2x *bp = params->bp;
12273 u32 lss_status = 0;
12274 u32 mac_base;
12275 /* In case link status is physically up @ 10G do */
12276 if ((vars->phy_flags & PHY_PHYSICAL_LINK_FLAG) == 0)
12277 return;
12278
12279 if (CHIP_IS_E3(bp) &&
12280 (REG_RD(bp, MISC_REG_RESET_REG_2) &
12281 (MISC_REGISTERS_RESET_REG_2_XMAC))) {
12282 /* Check E3 XMAC */
12283 /*
12284 * Note that link speed cannot be queried here, since it may be
12285 * zero while link is down. In case UMAC is active, LSS will
12286 * simply not be set
12287 */
12288 mac_base = (params->port) ? GRCBASE_XMAC1 : GRCBASE_XMAC0;
12289
12290 /* Clear stick bits (Requires rising edge) */
12291 REG_WR(bp, mac_base + XMAC_REG_CLEAR_RX_LSS_STATUS, 0);
12292 REG_WR(bp, mac_base + XMAC_REG_CLEAR_RX_LSS_STATUS,
12293 XMAC_CLEAR_RX_LSS_STATUS_REG_CLEAR_LOCAL_FAULT_STATUS |
12294 XMAC_CLEAR_RX_LSS_STATUS_REG_CLEAR_REMOTE_FAULT_STATUS);
12295 if (REG_RD(bp, mac_base + XMAC_REG_RX_LSS_STATUS))
12296 lss_status = 1;
12297
12298 bnx2x_analyze_link_error(params, vars, lss_status);
12299 } else if (REG_RD(bp, MISC_REG_RESET_REG_2) &
12300 (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << params->port)) {
12301 /* Check E1X / E2 BMAC */
12302 u32 lss_status_reg;
12303 u32 wb_data[2];
12304 mac_base = params->port ? NIG_REG_INGRESS_BMAC1_MEM :
12305 NIG_REG_INGRESS_BMAC0_MEM;
12306 /* Read BIGMAC_REGISTER_RX_LSS_STATUS */
12307 if (CHIP_IS_E2(bp))
12308 lss_status_reg = BIGMAC2_REGISTER_RX_LSS_STAT;
12309 else
12310 lss_status_reg = BIGMAC_REGISTER_RX_LSS_STATUS;
12311
12312 REG_RD_DMAE(bp, mac_base + lss_status_reg, wb_data, 2);
12313 lss_status = (wb_data[0] > 0);
12314
12315 bnx2x_analyze_link_error(params, vars, lss_status);
12316 }
12317 }
12318
12319 void bnx2x_period_func(struct link_params *params, struct link_vars *vars)
12320 {
12321 struct bnx2x *bp = params->bp;
12322 u16 phy_idx;
12323 if (!params) {
12324 DP(NETIF_MSG_LINK, "Uninitialized params !\n");
12325 return;
12326 }
12327
12328 for (phy_idx = INT_PHY; phy_idx < MAX_PHYS; phy_idx++) {
12329 if (params->phy[phy_idx].flags & FLAGS_TX_ERROR_CHECK) {
12330 bnx2x_set_aer_mmd(params, &params->phy[phy_idx]);
12331 bnx2x_check_half_open_conn(params, vars);
12332 break;
12333 }
12334 }
12335
12336 if (CHIP_IS_E3(bp))
12337 bnx2x_check_over_curr(params, vars);
12338 }
12339
12340 u8 bnx2x_hw_lock_required(struct bnx2x *bp, u32 shmem_base, u32 shmem2_base)
12341 {
12342 u8 phy_index;
12343 struct bnx2x_phy phy;
12344 for (phy_index = INT_PHY; phy_index < MAX_PHYS;
12345 phy_index++) {
12346 if (bnx2x_populate_phy(bp, phy_index, shmem_base, shmem2_base,
12347 0, &phy) != 0) {
12348 DP(NETIF_MSG_LINK, "populate phy failed\n");
12349 return 0;
12350 }
12351
12352 if (phy.flags & FLAGS_HW_LOCK_REQUIRED)
12353 return 1;
12354 }
12355 return 0;
12356 }
12357
12358 u8 bnx2x_fan_failure_det_req(struct bnx2x *bp,
12359 u32 shmem_base,
12360 u32 shmem2_base,
12361 u8 port)
12362 {
12363 u8 phy_index, fan_failure_det_req = 0;
12364 struct bnx2x_phy phy;
12365 for (phy_index = EXT_PHY1; phy_index < MAX_PHYS;
12366 phy_index++) {
12367 if (bnx2x_populate_phy(bp, phy_index, shmem_base, shmem2_base,
12368 port, &phy)
12369 != 0) {
12370 DP(NETIF_MSG_LINK, "populate phy failed\n");
12371 return 0;
12372 }
12373 fan_failure_det_req |= (phy.flags &
12374 FLAGS_FAN_FAILURE_DET_REQ);
12375 }
12376 return fan_failure_det_req;
12377 }
12378
12379 void bnx2x_hw_reset_phy(struct link_params *params)
12380 {
12381 u8 phy_index;
12382 struct bnx2x *bp = params->bp;
12383 bnx2x_update_mng(params, 0);
12384 bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 + params->port*4,
12385 (NIG_MASK_XGXS0_LINK_STATUS |
12386 NIG_MASK_XGXS0_LINK10G |
12387 NIG_MASK_SERDES0_LINK_STATUS |
12388 NIG_MASK_MI_INT));
12389
12390 for (phy_index = INT_PHY; phy_index < MAX_PHYS;
12391 phy_index++) {
12392 if (params->phy[phy_index].hw_reset) {
12393 params->phy[phy_index].hw_reset(
12394 &params->phy[phy_index],
12395 params);
12396 params->phy[phy_index] = phy_null;
12397 }
12398 }
12399 }
12400
12401 void bnx2x_init_mod_abs_int(struct bnx2x *bp, struct link_vars *vars,
12402 u32 chip_id, u32 shmem_base, u32 shmem2_base,
12403 u8 port)
12404 {
12405 u8 gpio_num = 0xff, gpio_port = 0xff, phy_index;
12406 u32 val;
12407 u32 offset, aeu_mask, swap_val, swap_override, sync_offset;
12408 if (CHIP_IS_E3(bp)) {
12409 if (bnx2x_get_mod_abs_int_cfg(bp, chip_id,
12410 shmem_base,
12411 port,
12412 &gpio_num,
12413 &gpio_port) != 0)
12414 return;
12415 } else {
12416 struct bnx2x_phy phy;
12417 for (phy_index = EXT_PHY1; phy_index < MAX_PHYS;
12418 phy_index++) {
12419 if (bnx2x_populate_phy(bp, phy_index, shmem_base,
12420 shmem2_base, port, &phy)
12421 != 0) {
12422 DP(NETIF_MSG_LINK, "populate phy failed\n");
12423 return;
12424 }
12425 if (phy.type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726) {
12426 gpio_num = MISC_REGISTERS_GPIO_3;
12427 gpio_port = port;
12428 break;
12429 }
12430 }
12431 }
12432
12433 if (gpio_num == 0xff)
12434 return;
12435
12436 /* Set GPIO3 to trigger SFP+ module insertion/removal */
12437 bnx2x_set_gpio(bp, gpio_num, MISC_REGISTERS_GPIO_INPUT_HI_Z, gpio_port);
12438
12439 swap_val = REG_RD(bp, NIG_REG_PORT_SWAP);
12440 swap_override = REG_RD(bp, NIG_REG_STRAP_OVERRIDE);
12441 gpio_port ^= (swap_val && swap_override);
12442
12443 vars->aeu_int_mask = AEU_INPUTS_ATTN_BITS_GPIO0_FUNCTION_0 <<
12444 (gpio_num + (gpio_port << 2));
12445
12446 sync_offset = shmem_base +
12447 offsetof(struct shmem_region,
12448 dev_info.port_hw_config[port].aeu_int_mask);
12449 REG_WR(bp, sync_offset, vars->aeu_int_mask);
12450
12451 DP(NETIF_MSG_LINK, "Setting MOD_ABS (GPIO%d_P%d) AEU to 0x%x\n",
12452 gpio_num, gpio_port, vars->aeu_int_mask);
12453
12454 if (port == 0)
12455 offset = MISC_REG_AEU_ENABLE1_FUNC_0_OUT_0;
12456 else
12457 offset = MISC_REG_AEU_ENABLE1_FUNC_1_OUT_0;
12458
12459 /* Open appropriate AEU for interrupts */
12460 aeu_mask = REG_RD(bp, offset);
12461 aeu_mask |= vars->aeu_int_mask;
12462 REG_WR(bp, offset, aeu_mask);
12463
12464 /* Enable the GPIO to trigger interrupt */
12465 val = REG_RD(bp, MISC_REG_GPIO_EVENT_EN);
12466 val |= 1 << (gpio_num + (gpio_port << 2));
12467 REG_WR(bp, MISC_REG_GPIO_EVENT_EN, val);
12468 }
ubuntu-bionic-kernel mirror