Merge tag 'locking-urgent-2021-07-25' of git://git.kernel.org/pub/scm/linux/kernel...

[mirror_ubuntu-jammy-kernel.git] / drivers / net / dsa / sja1105 / sja1105_main.c

// SPDX-License-Identifier: GPL-2.0
/* Copyright (c) 2018, Sensor-Technik Wiedemann GmbH
 * Copyright (c) 2018-2019, Vladimir Oltean <olteanv@gmail.com>
 */

#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt

#include <linux/delay.h>
#include <linux/module.h>
#include <linux/printk.h>
#include <linux/spi/spi.h>
#include <linux/errno.h>
#include <linux/gpio/consumer.h>
#include <linux/phylink.h>
#include <linux/of.h>
#include <linux/of_net.h>
#include <linux/of_mdio.h>
#include <linux/of_device.h>
#include <linux/pcs/pcs-xpcs.h>
#include <linux/netdev_features.h>
#include <linux/netdevice.h>
#include <linux/if_bridge.h>
#include <linux/if_ether.h>
#include <linux/dsa/8021q.h>
#include "sja1105.h"
#include "sja1105_tas.h"

#define SJA1105_UNKNOWN_MULTICAST       0x010000000000ull
#define SJA1105_DEFAULT_VLAN            (VLAN_N_VID - 1)

static const struct dsa_switch_ops sja1105_switch_ops;

static void sja1105_hw_reset(struct gpio_desc *gpio, unsigned int pulse_len,
                             unsigned int startup_delay)
{
        gpiod_set_value_cansleep(gpio, 1);
        /* Wait for minimum reset pulse length */
        msleep(pulse_len);
        gpiod_set_value_cansleep(gpio, 0);
        /* Wait until chip is ready after reset */
        msleep(startup_delay);
}

static void
sja1105_port_allow_traffic(struct sja1105_l2_forwarding_entry *l2_fwd,
                           int from, int to, bool allow)
{
        if (allow)
                l2_fwd[from].reach_port |= BIT(to);
        else
                l2_fwd[from].reach_port &= ~BIT(to);
}

static bool sja1105_can_forward(struct sja1105_l2_forwarding_entry *l2_fwd,
                                int from, int to)
{
        return !!(l2_fwd[from].reach_port & BIT(to));
}

static int sja1105_init_mac_settings(struct sja1105_private *priv)
{
        struct sja1105_mac_config_entry default_mac = {
                /* Enable all 8 priority queues on egress.
                 * Every queue i holds top[i] - base[i] frames.
                 * Sum of top[i] - base[i] is 511 (max hardware limit).
                 */
                .top  = {0x3F, 0x7F, 0xBF, 0xFF, 0x13F, 0x17F, 0x1BF, 0x1FF},
                .base = {0x0, 0x40, 0x80, 0xC0, 0x100, 0x140, 0x180, 0x1C0},
                .enabled = {true, true, true, true, true, true, true, true},
                /* Keep standard IFG of 12 bytes on egress. */
                .ifg = 0,
                /* Always put the MAC speed in automatic mode, where it can be
                 * adjusted at runtime by PHYLINK.
                 */
                .speed = priv->info->port_speed[SJA1105_SPEED_AUTO],
                /* No static correction for 1-step 1588 events */
                .tp_delin = 0,
                .tp_delout = 0,
                /* Disable aging for critical TTEthernet traffic */
                .maxage = 0xFF,
                /* Internal VLAN (pvid) to apply to untagged ingress */
                .vlanprio = 0,
                .vlanid = 1,
                .ing_mirr = false,
                .egr_mirr = false,
                /* Don't drop traffic with other EtherType than ETH_P_IP */
                .drpnona664 = false,
                /* Don't drop double-tagged traffic */
                .drpdtag = false,
                /* Don't drop untagged traffic */
                .drpuntag = false,
                /* Don't retag 802.1p (VID 0) traffic with the pvid */
                .retag = false,
                /* Disable learning and I/O on user ports by default -
                 * STP will enable it.
                 */
                .dyn_learn = false,
                .egress = false,
                .ingress = false,
        };
        struct sja1105_mac_config_entry *mac;
        struct dsa_switch *ds = priv->ds;
        struct sja1105_table *table;
        int i;

        table = &priv->static_config.tables[BLK_IDX_MAC_CONFIG];

        /* Discard previous MAC Configuration Table */
        if (table->entry_count) {
                kfree(table->entries);
                table->entry_count = 0;
        }

        table->entries = kcalloc(table->ops->max_entry_count,
                                 table->ops->unpacked_entry_size, GFP_KERNEL);
        if (!table->entries)
                return -ENOMEM;

        table->entry_count = table->ops->max_entry_count;

        mac = table->entries;

        for (i = 0; i < ds->num_ports; i++) {
                mac[i] = default_mac;

                /* Let sja1105_bridge_stp_state_set() keep address learning
                 * enabled for the CPU port.
                 */
                if (dsa_is_cpu_port(ds, i))
                        priv->learn_ena |= BIT(i);
        }

        return 0;
}

static int sja1105_init_mii_settings(struct sja1105_private *priv)
{
        struct device *dev = &priv->spidev->dev;
        struct sja1105_xmii_params_entry *mii;
        struct dsa_switch *ds = priv->ds;
        struct sja1105_table *table;
        int i;

        table = &priv->static_config.tables[BLK_IDX_XMII_PARAMS];

        /* Discard previous xMII Mode Parameters Table */
        if (table->entry_count) {
                kfree(table->entries);
                table->entry_count = 0;
        }

        table->entries = kcalloc(table->ops->max_entry_count,
                                 table->ops->unpacked_entry_size, GFP_KERNEL);
        if (!table->entries)
                return -ENOMEM;

        /* Override table based on PHYLINK DT bindings */
        table->entry_count = table->ops->max_entry_count;

        mii = table->entries;

        for (i = 0; i < ds->num_ports; i++) {
                sja1105_mii_role_t role = XMII_MAC;

                if (dsa_is_unused_port(priv->ds, i))
                        continue;

                switch (priv->phy_mode[i]) {
                case PHY_INTERFACE_MODE_INTERNAL:
                        if (priv->info->internal_phy[i] == SJA1105_NO_PHY)
                                goto unsupported;

                        mii->xmii_mode[i] = XMII_MODE_MII;
                        if (priv->info->internal_phy[i] == SJA1105_PHY_BASE_TX)
                                mii->special[i] = true;

                        break;
                case PHY_INTERFACE_MODE_REVMII:
                        role = XMII_PHY;
                        fallthrough;
                case PHY_INTERFACE_MODE_MII:
                        if (!priv->info->supports_mii[i])
                                goto unsupported;

                        mii->xmii_mode[i] = XMII_MODE_MII;
                        break;
                case PHY_INTERFACE_MODE_REVRMII:
                        role = XMII_PHY;
                        fallthrough;
                case PHY_INTERFACE_MODE_RMII:
                        if (!priv->info->supports_rmii[i])
                                goto unsupported;

                        mii->xmii_mode[i] = XMII_MODE_RMII;
                        break;
                case PHY_INTERFACE_MODE_RGMII:
                case PHY_INTERFACE_MODE_RGMII_ID:
                case PHY_INTERFACE_MODE_RGMII_RXID:
                case PHY_INTERFACE_MODE_RGMII_TXID:
                        if (!priv->info->supports_rgmii[i])
                                goto unsupported;

                        mii->xmii_mode[i] = XMII_MODE_RGMII;
                        break;
                case PHY_INTERFACE_MODE_SGMII:
                        if (!priv->info->supports_sgmii[i])
                                goto unsupported;

                        mii->xmii_mode[i] = XMII_MODE_SGMII;
                        mii->special[i] = true;
                        break;
                case PHY_INTERFACE_MODE_2500BASEX:
                        if (!priv->info->supports_2500basex[i])
                                goto unsupported;

                        mii->xmii_mode[i] = XMII_MODE_SGMII;
                        mii->special[i] = true;
                        break;
unsupported:
                default:
                        dev_err(dev, "Unsupported PHY mode %s on port %d!\n",
                                phy_modes(priv->phy_mode[i]), i);
                        return -EINVAL;
                }

                mii->phy_mac[i] = role;
        }
        return 0;
}

static int sja1105_init_static_fdb(struct sja1105_private *priv)
{
        struct sja1105_l2_lookup_entry *l2_lookup;
        struct sja1105_table *table;
        int port;

        table = &priv->static_config.tables[BLK_IDX_L2_LOOKUP];

        /* We only populate the FDB table through dynamic L2 Address Lookup
         * entries, except for a special entry at the end which is a catch-all
         * for unknown multicast and will be used to control flooding domain.
         */
        if (table->entry_count) {
                kfree(table->entries);
                table->entry_count = 0;
        }

        if (!priv->info->can_limit_mcast_flood)
                return 0;

        table->entries = kcalloc(1, table->ops->unpacked_entry_size,
                                 GFP_KERNEL);
        if (!table->entries)
                return -ENOMEM;

        table->entry_count = 1;
        l2_lookup = table->entries;

        /* All L2 multicast addresses have an odd first octet */
        l2_lookup[0].macaddr = SJA1105_UNKNOWN_MULTICAST;
        l2_lookup[0].mask_macaddr = SJA1105_UNKNOWN_MULTICAST;
        l2_lookup[0].lockeds = true;
        l2_lookup[0].index = SJA1105_MAX_L2_LOOKUP_COUNT - 1;

        /* Flood multicast to every port by default */
        for (port = 0; port < priv->ds->num_ports; port++)
                if (!dsa_is_unused_port(priv->ds, port))
                        l2_lookup[0].destports |= BIT(port);

        return 0;
}

static int sja1105_init_l2_lookup_params(struct sja1105_private *priv)
{
        struct sja1105_l2_lookup_params_entry default_l2_lookup_params = {
                /* Learned FDB entries are forgotten after 300 seconds */
                .maxage = SJA1105_AGEING_TIME_MS(300000),
                /* All entries within a FDB bin are available for learning */
                .dyn_tbsz = SJA1105ET_FDB_BIN_SIZE,
                /* And the P/Q/R/S equivalent setting: */
                .start_dynspc = 0,
                /* 2^8 + 2^5 + 2^3 + 2^2 + 2^1 + 1 in Koopman notation */
                .poly = 0x97,
                /* This selects between Independent VLAN Learning (IVL) and
                 * Shared VLAN Learning (SVL)
                 */
                .shared_learn = true,
                /* Don't discard management traffic based on ENFPORT -
                 * we don't perform SMAC port enforcement anyway, so
                 * what we are setting here doesn't matter.
                 */
                .no_enf_hostprt = false,
                /* Don't learn SMAC for mac_fltres1 and mac_fltres0.
                 * Maybe correlate with no_linklocal_learn from bridge driver?
                 */
                .no_mgmt_learn = true,
                /* P/Q/R/S only */
                .use_static = true,
                /* Dynamically learned FDB entries can overwrite other (older)
                 * dynamic FDB entries
                 */
                .owr_dyn = true,
                .drpnolearn = true,
        };
        struct dsa_switch *ds = priv->ds;
        int port, num_used_ports = 0;
        struct sja1105_table *table;
        u64 max_fdb_entries;

        for (port = 0; port < ds->num_ports; port++)
                if (!dsa_is_unused_port(ds, port))
                        num_used_ports++;

        max_fdb_entries = SJA1105_MAX_L2_LOOKUP_COUNT / num_used_ports;

        for (port = 0; port < ds->num_ports; port++) {
                if (dsa_is_unused_port(ds, port))
                        continue;

                default_l2_lookup_params.maxaddrp[port] = max_fdb_entries;
        }

        table = &priv->static_config.tables[BLK_IDX_L2_LOOKUP_PARAMS];

        if (table->entry_count) {
                kfree(table->entries);
                table->entry_count = 0;
        }

        table->entries = kcalloc(table->ops->max_entry_count,
                                 table->ops->unpacked_entry_size, GFP_KERNEL);
        if (!table->entries)
                return -ENOMEM;

        table->entry_count = table->ops->max_entry_count;

        /* This table only has a single entry */
        ((struct sja1105_l2_lookup_params_entry *)table->entries)[0] =
                                default_l2_lookup_params;

        return 0;
}

/* Set up a default VLAN for untagged traffic injected from the CPU
 * using management routes (e.g. STP, PTP) as opposed to tag_8021q.
 * All DT-defined ports are members of this VLAN, and there are no
 * restrictions on forwarding (since the CPU selects the destination).
 * Frames from this VLAN will always be transmitted as untagged, and
 * neither the bridge nor the 8021q module cannot create this VLAN ID.
 */
static int sja1105_init_static_vlan(struct sja1105_private *priv)
{
        struct sja1105_table *table;
        struct sja1105_vlan_lookup_entry pvid = {
                .type_entry = SJA1110_VLAN_D_TAG,
                .ving_mirr = 0,
                .vegr_mirr = 0,
                .vmemb_port = 0,
                .vlan_bc = 0,
                .tag_port = 0,
                .vlanid = SJA1105_DEFAULT_VLAN,
        };
        struct dsa_switch *ds = priv->ds;
        int port;

        table = &priv->static_config.tables[BLK_IDX_VLAN_LOOKUP];

        if (table->entry_count) {
                kfree(table->entries);
                table->entry_count = 0;
        }

        table->entries = kzalloc(table->ops->unpacked_entry_size,
                                 GFP_KERNEL);
        if (!table->entries)
                return -ENOMEM;

        table->entry_count = 1;

        for (port = 0; port < ds->num_ports; port++) {
                struct sja1105_bridge_vlan *v;

                if (dsa_is_unused_port(ds, port))
                        continue;

                pvid.vmemb_port |= BIT(port);
                pvid.vlan_bc |= BIT(port);
                pvid.tag_port &= ~BIT(port);

                v = kzalloc(sizeof(*v), GFP_KERNEL);
                if (!v)
                        return -ENOMEM;

                v->port = port;
                v->vid = SJA1105_DEFAULT_VLAN;
                v->untagged = true;
                if (dsa_is_cpu_port(ds, port))
                        v->pvid = true;
                list_add(&v->list, &priv->dsa_8021q_vlans);

                v = kmemdup(v, sizeof(*v), GFP_KERNEL);
                if (!v)
                        return -ENOMEM;

                list_add(&v->list, &priv->bridge_vlans);
        }

        ((struct sja1105_vlan_lookup_entry *)table->entries)[0] = pvid;
        return 0;
}

static int sja1105_init_l2_forwarding(struct sja1105_private *priv)
{
        struct sja1105_l2_forwarding_entry *l2fwd;
        struct dsa_switch *ds = priv->ds;
        struct sja1105_table *table;
        int i, j;

        table = &priv->static_config.tables[BLK_IDX_L2_FORWARDING];

        if (table->entry_count) {
                kfree(table->entries);
                table->entry_count = 0;
        }

        table->entries = kcalloc(table->ops->max_entry_count,
                                 table->ops->unpacked_entry_size, GFP_KERNEL);
        if (!table->entries)
                return -ENOMEM;

        table->entry_count = table->ops->max_entry_count;

        l2fwd = table->entries;

        /* First 5 entries define the forwarding rules */
        for (i = 0; i < ds->num_ports; i++) {
                unsigned int upstream = dsa_upstream_port(priv->ds, i);

                if (dsa_is_unused_port(ds, i))
                        continue;

                for (j = 0; j < SJA1105_NUM_TC; j++)
                        l2fwd[i].vlan_pmap[j] = j;

                /* All ports start up with egress flooding enabled,
                 * including the CPU port.
                 */
                priv->ucast_egress_floods |= BIT(i);
                priv->bcast_egress_floods |= BIT(i);

                if (i == upstream)
                        continue;

                sja1105_port_allow_traffic(l2fwd, i, upstream, true);
                sja1105_port_allow_traffic(l2fwd, upstream, i, true);

                l2fwd[i].bc_domain = BIT(upstream);
                l2fwd[i].fl_domain = BIT(upstream);

                l2fwd[upstream].bc_domain |= BIT(i);
                l2fwd[upstream].fl_domain |= BIT(i);
        }

        /* Next 8 entries define VLAN PCP mapping from ingress to egress.
         * Create a one-to-one mapping.
         */
        for (i = 0; i < SJA1105_NUM_TC; i++) {
                for (j = 0; j < ds->num_ports; j++) {
                        if (dsa_is_unused_port(ds, j))
                                continue;

                        l2fwd[ds->num_ports + i].vlan_pmap[j] = i;
                }

                l2fwd[ds->num_ports + i].type_egrpcp2outputq = true;
        }

        return 0;
}

static int sja1110_init_pcp_remapping(struct sja1105_private *priv)
{
        struct sja1110_pcp_remapping_entry *pcp_remap;
        struct dsa_switch *ds = priv->ds;
        struct sja1105_table *table;
        int port, tc;

        table = &priv->static_config.tables[BLK_IDX_PCP_REMAPPING];

        /* Nothing to do for SJA1105 */
        if (!table->ops->max_entry_count)
                return 0;

        if (table->entry_count) {
                kfree(table->entries);
                table->entry_count = 0;
        }

        table->entries = kcalloc(table->ops->max_entry_count,
                                 table->ops->unpacked_entry_size, GFP_KERNEL);
        if (!table->entries)
                return -ENOMEM;

        table->entry_count = table->ops->max_entry_count;

        pcp_remap = table->entries;

        /* Repeat the configuration done for vlan_pmap */
        for (port = 0; port < ds->num_ports; port++) {
                if (dsa_is_unused_port(ds, port))
                        continue;

                for (tc = 0; tc < SJA1105_NUM_TC; tc++)
                        pcp_remap[port].egrpcp[tc] = tc;
        }

        return 0;
}

static int sja1105_init_l2_forwarding_params(struct sja1105_private *priv)
{
        struct sja1105_l2_forwarding_params_entry *l2fwd_params;
        struct sja1105_table *table;

        table = &priv->static_config.tables[BLK_IDX_L2_FORWARDING_PARAMS];

        if (table->entry_count) {
                kfree(table->entries);
                table->entry_count = 0;
        }

        table->entries = kcalloc(table->ops->max_entry_count,
                                 table->ops->unpacked_entry_size, GFP_KERNEL);
        if (!table->entries)
                return -ENOMEM;

        table->entry_count = table->ops->max_entry_count;

        /* This table only has a single entry */
        l2fwd_params = table->entries;

        /* Disallow dynamic reconfiguration of vlan_pmap */
        l2fwd_params->max_dynp = 0;
        /* Use a single memory partition for all ingress queues */
        l2fwd_params->part_spc[0] = priv->info->max_frame_mem;

        return 0;
}

void sja1105_frame_memory_partitioning(struct sja1105_private *priv)
{
        struct sja1105_l2_forwarding_params_entry *l2_fwd_params;
        struct sja1105_vl_forwarding_params_entry *vl_fwd_params;
        int max_mem = priv->info->max_frame_mem;
        struct sja1105_table *table;

        /* VLAN retagging is implemented using a loopback port that consumes
         * frame buffers. That leaves less for us.
         */
        if (priv->vlan_state == SJA1105_VLAN_BEST_EFFORT)
                max_mem -= SJA1105_FRAME_MEMORY_RETAGGING_OVERHEAD;

        table = &priv->static_config.tables[BLK_IDX_L2_FORWARDING_PARAMS];
        l2_fwd_params = table->entries;
        l2_fwd_params->part_spc[0] = max_mem;

        /* If we have any critical-traffic virtual links, we need to reserve
         * some frame buffer memory for them. At the moment, hardcode the value
         * at 100 blocks of 128 bytes of memory each. This leaves 829 blocks
         * remaining for best-effort traffic. TODO: figure out a more flexible
         * way to perform the frame buffer partitioning.
         */
        if (!priv->static_config.tables[BLK_IDX_VL_FORWARDING].entry_count)
                return;

        table = &priv->static_config.tables[BLK_IDX_VL_FORWARDING_PARAMS];
        vl_fwd_params = table->entries;

        l2_fwd_params->part_spc[0] -= SJA1105_VL_FRAME_MEMORY;
        vl_fwd_params->partspc[0] = SJA1105_VL_FRAME_MEMORY;
}

/* SJA1110 TDMACONFIGIDX values:
 *
 *      | 100 Mbps ports |  1Gbps ports  | 2.5Gbps ports | Disabled ports
 * -----+----------------+---------------+---------------+---------------
 *   0  |   0, [5:10]    |     [1:2]     |     [3:4]     |     retag
 *   1  |0, [5:10], retag|     [1:2]     |     [3:4]     |       -
 *   2  |   0, [5:10]    |  [1:3], retag |       4       |       -
 *   3  |   0, [5:10]    |[1:2], 4, retag|       3       |       -
 *   4  |  0, 2, [5:10]  |    1, retag   |     [3:4]     |       -
 *   5  |  0, 1, [5:10]  |    2, retag   |     [3:4]     |       -
 *  14  |   0, [5:10]    | [1:4], retag  |       -       |       -
 *  15  |     [5:10]     | [0:4], retag  |       -       |       -
 */
static void sja1110_select_tdmaconfigidx(struct sja1105_private *priv)
{
        struct sja1105_general_params_entry *general_params;
        struct sja1105_table *table;
        bool port_1_is_base_tx;
        bool port_3_is_2500;
        bool port_4_is_2500;
        u64 tdmaconfigidx;

        if (priv->info->device_id != SJA1110_DEVICE_ID)
                return;

        table = &priv->static_config.tables[BLK_IDX_GENERAL_PARAMS];
        general_params = table->entries;

        /* All the settings below are "as opposed to SGMII", which is the
         * other pinmuxing option.
         */
        port_1_is_base_tx = priv->phy_mode[1] == PHY_INTERFACE_MODE_INTERNAL;
        port_3_is_2500 = priv->phy_mode[3] == PHY_INTERFACE_MODE_2500BASEX;
        port_4_is_2500 = priv->phy_mode[4] == PHY_INTERFACE_MODE_2500BASEX;

        if (port_1_is_base_tx)
                /* Retagging port will operate at 1 Gbps */
                tdmaconfigidx = 5;
        else if (port_3_is_2500 && port_4_is_2500)
                /* Retagging port will operate at 100 Mbps */
                tdmaconfigidx = 1;
        else if (port_3_is_2500)
                /* Retagging port will operate at 1 Gbps */
                tdmaconfigidx = 3;
        else if (port_4_is_2500)
                /* Retagging port will operate at 1 Gbps */
                tdmaconfigidx = 2;
        else
                /* Retagging port will operate at 1 Gbps */
                tdmaconfigidx = 14;

        general_params->tdmaconfigidx = tdmaconfigidx;
}

static int sja1105_init_general_params(struct sja1105_private *priv)
{
        struct sja1105_general_params_entry default_general_params = {
                /* Allow dynamic changing of the mirror port */
                .mirr_ptacu = true,
                .switchid = priv->ds->index,
                /* Priority queue for link-local management frames
                 * (both ingress to and egress from CPU - PTP, STP etc)
                 */
                .hostprio = 7,
                .mac_fltres1 = SJA1105_LINKLOCAL_FILTER_A,
                .mac_flt1    = SJA1105_LINKLOCAL_FILTER_A_MASK,
                .incl_srcpt1 = false,
                .send_meta1  = false,
                .mac_fltres0 = SJA1105_LINKLOCAL_FILTER_B,
                .mac_flt0    = SJA1105_LINKLOCAL_FILTER_B_MASK,
                .incl_srcpt0 = false,
                .send_meta0  = false,
                /* The destination for traffic matching mac_fltres1 and
                 * mac_fltres0 on all ports except host_port. Such traffic
                 * receieved on host_port itself would be dropped, except
                 * by installing a temporary 'management route'
                 */
                .host_port = priv->ds->num_ports,
                /* Default to an invalid value */
                .mirr_port = priv->ds->num_ports,
                /* No TTEthernet */
                .vllupformat = SJA1105_VL_FORMAT_PSFP,
                .vlmarker = 0,
                .vlmask = 0,
                /* Only update correctionField for 1-step PTP (L2 transport) */
                .ignore2stf = 0,
                /* Forcefully disable VLAN filtering by telling
                 * the switch that VLAN has a different EtherType.
                 */
                .tpid = ETH_P_SJA1105,
                .tpid2 = ETH_P_SJA1105,
                /* Enable the TTEthernet engine on SJA1110 */
                .tte_en = true,
                /* Set up the EtherType for control packets on SJA1110 */
                .header_type = ETH_P_SJA1110,
        };
        struct sja1105_general_params_entry *general_params;
        struct dsa_switch *ds = priv->ds;
        struct sja1105_table *table;
        int port;

        for (port = 0; port < ds->num_ports; port++) {
                if (dsa_is_cpu_port(ds, port)) {
                        default_general_params.host_port = port;
                        break;
                }
        }

        table = &priv->static_config.tables[BLK_IDX_GENERAL_PARAMS];

        if (table->entry_count) {
                kfree(table->entries);
                table->entry_count = 0;
        }

        table->entries = kcalloc(table->ops->max_entry_count,
                                 table->ops->unpacked_entry_size, GFP_KERNEL);
        if (!table->entries)
                return -ENOMEM;

        table->entry_count = table->ops->max_entry_count;

        general_params = table->entries;

        /* This table only has a single entry */
        general_params[0] = default_general_params;

        sja1110_select_tdmaconfigidx(priv);

        /* Link-local traffic received on casc_port will be forwarded
         * to host_port without embedding the source port and device ID
         * info in the destination MAC address, and no RX timestamps will be
         * taken either (presumably because it is a cascaded port and a
         * downstream SJA switch already did that).
         * To disable the feature, we need to do different things depending on
         * switch generation. On SJA1105 we need to set an invalid port, while
         * on SJA1110 which support multiple cascaded ports, this field is a
         * bitmask so it must be left zero.
         */
        if (!priv->info->multiple_cascade_ports)
                general_params->casc_port = ds->num_ports;

        return 0;
}

static int sja1105_init_avb_params(struct sja1105_private *priv)
{
        struct sja1105_avb_params_entry *avb;
        struct sja1105_table *table;

        table = &priv->static_config.tables[BLK_IDX_AVB_PARAMS];

        /* Discard previous AVB Parameters Table */
        if (table->entry_count) {
                kfree(table->entries);
                table->entry_count = 0;
        }

        table->entries = kcalloc(table->ops->max_entry_count,
                                 table->ops->unpacked_entry_size, GFP_KERNEL);
        if (!table->entries)
                return -ENOMEM;

        table->entry_count = table->ops->max_entry_count;

        avb = table->entries;

        /* Configure the MAC addresses for meta frames */
        avb->destmeta = SJA1105_META_DMAC;
        avb->srcmeta  = SJA1105_META_SMAC;
        /* On P/Q/R/S, configure the direction of the PTP_CLK pin as input by
         * default. This is because there might be boards with a hardware
         * layout where enabling the pin as output might cause an electrical
         * clash. On E/T the pin is always an output, which the board designers
         * probably already knew, so even if there are going to be electrical
         * issues, there's nothing we can do.
         */
        avb->cas_master = false;

        return 0;
}

/* The L2 policing table is 2-stage. The table is looked up for each frame
 * according to the ingress port, whether it was broadcast or not, and the
 * classified traffic class (given by VLAN PCP). This portion of the lookup is
 * fixed, and gives access to the SHARINDX, an indirection register pointing
 * within the policing table itself, which is used to resolve the policer that
 * will be used for this frame.
 *
 *  Stage 1                              Stage 2
 * +------------+--------+              +---------------------------------+
 * |Port 0 TC 0 |SHARINDX|              | Policer 0: Rate, Burst, MTU     |
 * +------------+--------+              +---------------------------------+
 * |Port 0 TC 1 |SHARINDX|              | Policer 1: Rate, Burst, MTU     |
 * +------------+--------+              +---------------------------------+
 *    ...                               | Policer 2: Rate, Burst, MTU     |
 * +------------+--------+              +---------------------------------+
 * |Port 0 TC 7 |SHARINDX|              | Policer 3: Rate, Burst, MTU     |
 * +------------+--------+              +---------------------------------+
 * |Port 1 TC 0 |SHARINDX|              | Policer 4: Rate, Burst, MTU     |
 * +------------+--------+              +---------------------------------+
 *    ...                               | Policer 5: Rate, Burst, MTU     |
 * +------------+--------+              +---------------------------------+
 * |Port 1 TC 7 |SHARINDX|              | Policer 6: Rate, Burst, MTU     |
 * +------------+--------+              +---------------------------------+
 *    ...                               | Policer 7: Rate, Burst, MTU     |
 * +------------+--------+              +---------------------------------+
 * |Port 4 TC 7 |SHARINDX|                 ...
 * +------------+--------+
 * |Port 0 BCAST|SHARINDX|                 ...
 * +------------+--------+
 * |Port 1 BCAST|SHARINDX|                 ...
 * +------------+--------+
 *    ...                                  ...
 * +------------+--------+              +---------------------------------+
 * |Port 4 BCAST|SHARINDX|              | Policer 44: Rate, Burst, MTU    |
 * +------------+--------+              +---------------------------------+
 *
 * In this driver, we shall use policers 0-4 as statically alocated port
 * (matchall) policers. So we need to make the SHARINDX for all lookups
 * corresponding to this ingress port (8 VLAN PCP lookups and 1 broadcast
 * lookup) equal.
 * The remaining policers (40) shall be dynamically allocated for flower
 * policers, where the key is either vlan_prio or dst_mac ff:ff:ff:ff:ff:ff.
 */
#define SJA1105_RATE_MBPS(speed) (((speed) * 64000) / 1000)

static int sja1105_init_l2_policing(struct sja1105_private *priv)
{
        struct sja1105_l2_policing_entry *policing;
        struct dsa_switch *ds = priv->ds;
        struct sja1105_table *table;
        int port, tc;

        table = &priv->static_config.tables[BLK_IDX_L2_POLICING];

        /* Discard previous L2 Policing Table */
        if (table->entry_count) {
                kfree(table->entries);
                table->entry_count = 0;
        }

        table->entries = kcalloc(table->ops->max_entry_count,
                                 table->ops->unpacked_entry_size, GFP_KERNEL);
        if (!table->entries)
                return -ENOMEM;

        table->entry_count = table->ops->max_entry_count;

        policing = table->entries;

        /* Setup shared indices for the matchall policers */
        for (port = 0; port < ds->num_ports; port++) {
                int mcast = (ds->num_ports * (SJA1105_NUM_TC + 1)) + port;
                int bcast = (ds->num_ports * SJA1105_NUM_TC) + port;

                for (tc = 0; tc < SJA1105_NUM_TC; tc++)
                        policing[port * SJA1105_NUM_TC + tc].sharindx = port;

                policing[bcast].sharindx = port;
                /* Only SJA1110 has multicast policers */
                if (mcast <= table->ops->max_entry_count)
                        policing[mcast].sharindx = port;
        }

        /* Setup the matchall policer parameters */
        for (port = 0; port < ds->num_ports; port++) {
                int mtu = VLAN_ETH_FRAME_LEN + ETH_FCS_LEN;

                if (dsa_is_cpu_port(priv->ds, port))
                        mtu += VLAN_HLEN;

                policing[port].smax = 65535; /* Burst size in bytes */
                policing[port].rate = SJA1105_RATE_MBPS(1000);
                policing[port].maxlen = mtu;
                policing[port].partition = 0;
        }

        return 0;
}

static int sja1105_static_config_load(struct sja1105_private *priv)
{
        int rc;

        sja1105_static_config_free(&priv->static_config);
        rc = sja1105_static_config_init(&priv->static_config,
                                        priv->info->static_ops,
                                        priv->info->device_id);
        if (rc)
                return rc;

        /* Build static configuration */
        rc = sja1105_init_mac_settings(priv);
        if (rc < 0)
                return rc;
        rc = sja1105_init_mii_settings(priv);
        if (rc < 0)
                return rc;
        rc = sja1105_init_static_fdb(priv);
        if (rc < 0)
                return rc;
        rc = sja1105_init_static_vlan(priv);
        if (rc < 0)
                return rc;
        rc = sja1105_init_l2_lookup_params(priv);
        if (rc < 0)
                return rc;
        rc = sja1105_init_l2_forwarding(priv);
        if (rc < 0)
                return rc;
        rc = sja1105_init_l2_forwarding_params(priv);
        if (rc < 0)
                return rc;
        rc = sja1105_init_l2_policing(priv);
        if (rc < 0)
                return rc;
        rc = sja1105_init_general_params(priv);
        if (rc < 0)
                return rc;
        rc = sja1105_init_avb_params(priv);
        if (rc < 0)
                return rc;
        rc = sja1110_init_pcp_remapping(priv);
        if (rc < 0)
                return rc;

        /* Send initial configuration to hardware via SPI */
        return sja1105_static_config_upload(priv);
}

static int sja1105_parse_rgmii_delays(struct sja1105_private *priv)
{
        struct dsa_switch *ds = priv->ds;
        int port;

        for (port = 0; port < ds->num_ports; port++) {
                if (!priv->fixed_link[port])
                        continue;

                if (priv->phy_mode[port] == PHY_INTERFACE_MODE_RGMII_RXID ||
                    priv->phy_mode[port] == PHY_INTERFACE_MODE_RGMII_ID)
                        priv->rgmii_rx_delay[port] = true;

                if (priv->phy_mode[port] == PHY_INTERFACE_MODE_RGMII_TXID ||
                    priv->phy_mode[port] == PHY_INTERFACE_MODE_RGMII_ID)
                        priv->rgmii_tx_delay[port] = true;

                if ((priv->rgmii_rx_delay[port] || priv->rgmii_tx_delay[port]) &&
                    !priv->info->setup_rgmii_delay)
                        return -EINVAL;
        }
        return 0;
}

static int sja1105_parse_ports_node(struct sja1105_private *priv,
                                    struct device_node *ports_node)
{
        struct device *dev = &priv->spidev->dev;
        struct device_node *child;

        for_each_available_child_of_node(ports_node, child) {
                struct device_node *phy_node;
                phy_interface_t phy_mode;
                u32 index;
                int err;

                /* Get switch port number from DT */
                if (of_property_read_u32(child, "reg", &index) < 0) {
                        dev_err(dev, "Port number not defined in device tree "
                                "(property \"reg\")\n");
                        of_node_put(child);
                        return -ENODEV;
                }

                /* Get PHY mode from DT */
                err = of_get_phy_mode(child, &phy_mode);
                if (err) {
                        dev_err(dev, "Failed to read phy-mode or "
                                "phy-interface-type property for port %d\n",
                                index);
                        of_node_put(child);
                        return -ENODEV;
                }

                phy_node = of_parse_phandle(child, "phy-handle", 0);
                if (!phy_node) {
                        if (!of_phy_is_fixed_link(child)) {
                                dev_err(dev, "phy-handle or fixed-link "
                                        "properties missing!\n");
                                of_node_put(child);
                                return -ENODEV;
                        }
                        /* phy-handle is missing, but fixed-link isn't.
                         * So it's a fixed link. Default to PHY role.
                         */
                        priv->fixed_link[index] = true;
                } else {
                        of_node_put(phy_node);
                }

                priv->phy_mode[index] = phy_mode;
        }

        return 0;
}

static int sja1105_parse_dt(struct sja1105_private *priv)
{
        struct device *dev = &priv->spidev->dev;
        struct device_node *switch_node = dev->of_node;
        struct device_node *ports_node;
        int rc;

        ports_node = of_get_child_by_name(switch_node, "ports");
        if (!ports_node)
                ports_node = of_get_child_by_name(switch_node, "ethernet-ports");
        if (!ports_node) {
                dev_err(dev, "Incorrect bindings: absent \"ports\" node\n");
                return -ENODEV;
        }

        rc = sja1105_parse_ports_node(priv, ports_node);
        of_node_put(ports_node);

        return rc;
}

/* Convert link speed from SJA1105 to ethtool encoding */
static int sja1105_port_speed_to_ethtool(struct sja1105_private *priv,
                                         u64 speed)
{
        if (speed == priv->info->port_speed[SJA1105_SPEED_10MBPS])
                return SPEED_10;
        if (speed == priv->info->port_speed[SJA1105_SPEED_100MBPS])
                return SPEED_100;
        if (speed == priv->info->port_speed[SJA1105_SPEED_1000MBPS])
                return SPEED_1000;
        if (speed == priv->info->port_speed[SJA1105_SPEED_2500MBPS])
                return SPEED_2500;
        return SPEED_UNKNOWN;
}

/* Set link speed in the MAC configuration for a specific port. */
static int sja1105_adjust_port_config(struct sja1105_private *priv, int port,
                                      int speed_mbps)
{
        struct sja1105_mac_config_entry *mac;
        struct device *dev = priv->ds->dev;
        u64 speed;
        int rc;

        /* On P/Q/R/S, one can read from the device via the MAC reconfiguration
         * tables. On E/T, MAC reconfig tables are not readable, only writable.
         * We have to *know* what the MAC looks like.  For the sake of keeping
         * the code common, we'll use the static configuration tables as a
         * reasonable approximation for both E/T and P/Q/R/S.
         */
        mac = priv->static_config.tables[BLK_IDX_MAC_CONFIG].entries;

        switch (speed_mbps) {
        case SPEED_UNKNOWN:
                /* PHYLINK called sja1105_mac_config() to inform us about
                 * the state->interface, but AN has not completed and the
                 * speed is not yet valid. UM10944.pdf says that setting
                 * SJA1105_SPEED_AUTO at runtime disables the port, so that is
                 * ok for power consumption in case AN will never complete -
                 * otherwise PHYLINK should come back with a new update.
                 */
                speed = priv->info->port_speed[SJA1105_SPEED_AUTO];
                break;
        case SPEED_10:
                speed = priv->info->port_speed[SJA1105_SPEED_10MBPS];
                break;
        case SPEED_100:
                speed = priv->info->port_speed[SJA1105_SPEED_100MBPS];
                break;
        case SPEED_1000:
                speed = priv->info->port_speed[SJA1105_SPEED_1000MBPS];
                break;
        case SPEED_2500:
                speed = priv->info->port_speed[SJA1105_SPEED_2500MBPS];
                break;
        default:
                dev_err(dev, "Invalid speed %iMbps\n", speed_mbps);
                return -EINVAL;
        }

        /* Overwrite SJA1105_SPEED_AUTO from the static MAC configuration
         * table, since this will be used for the clocking setup, and we no
         * longer need to store it in the static config (already told hardware
         * we want auto during upload phase).
         * Actually for the SGMII port, the MAC is fixed at 1 Gbps and
         * we need to configure the PCS only (if even that).
         */
        if (priv->phy_mode[port] == PHY_INTERFACE_MODE_SGMII)
                mac[port].speed = priv->info->port_speed[SJA1105_SPEED_1000MBPS];
        else if (priv->phy_mode[port] == PHY_INTERFACE_MODE_2500BASEX)
                mac[port].speed = priv->info->port_speed[SJA1105_SPEED_2500MBPS];
        else
                mac[port].speed = speed;

        /* Write to the dynamic reconfiguration tables */
        rc = sja1105_dynamic_config_write(priv, BLK_IDX_MAC_CONFIG, port,
                                          &mac[port], true);
        if (rc < 0) {
                dev_err(dev, "Failed to write MAC config: %d\n", rc);
                return rc;
        }

        /* Reconfigure the PLLs for the RGMII interfaces (required 125 MHz at
         * gigabit, 25 MHz at 100 Mbps and 2.5 MHz at 10 Mbps). For MII and
         * RMII no change of the clock setup is required. Actually, changing
         * the clock setup does interrupt the clock signal for a certain time
         * which causes trouble for all PHYs relying on this signal.
         */
        if (!phy_interface_mode_is_rgmii(priv->phy_mode[port]))
                return 0;

        return sja1105_clocking_setup_port(priv, port);
}

/* The SJA1105 MAC programming model is through the static config (the xMII
 * Mode table cannot be dynamically reconfigured), and we have to program
 * that early (earlier than PHYLINK calls us, anyway).
 * So just error out in case the connected PHY attempts to change the initial
 * system interface MII protocol from what is defined in the DT, at least for
 * now.
 */
static bool sja1105_phy_mode_mismatch(struct sja1105_private *priv, int port,
                                      phy_interface_t interface)
{
        return priv->phy_mode[port] != interface;
}

static void sja1105_mac_config(struct dsa_switch *ds, int port,
                               unsigned int mode,
                               const struct phylink_link_state *state)
{
        struct dsa_port *dp = dsa_to_port(ds, port);
        struct sja1105_private *priv = ds->priv;
        struct dw_xpcs *xpcs;

        if (sja1105_phy_mode_mismatch(priv, port, state->interface)) {
                dev_err(ds->dev, "Changing PHY mode to %s not supported!\n",
                        phy_modes(state->interface));
                return;
        }

        xpcs = priv->xpcs[port];

        if (xpcs)
                phylink_set_pcs(dp->pl, &xpcs->pcs);
}

static void sja1105_mac_link_down(struct dsa_switch *ds, int port,
                                  unsigned int mode,
                                  phy_interface_t interface)
{
        sja1105_inhibit_tx(ds->priv, BIT(port), true);
}

static void sja1105_mac_link_up(struct dsa_switch *ds, int port,
                                unsigned int mode,
                                phy_interface_t interface,
                                struct phy_device *phydev,
                                int speed, int duplex,
                                bool tx_pause, bool rx_pause)
{
        struct sja1105_private *priv = ds->priv;

        sja1105_adjust_port_config(priv, port, speed);

        sja1105_inhibit_tx(priv, BIT(port), false);
}

static void sja1105_phylink_validate(struct dsa_switch *ds, int port,
                                     unsigned long *supported,
                                     struct phylink_link_state *state)
{
        /* Construct a new mask which exhaustively contains all link features
         * supported by the MAC, and then apply that (logical AND) to what will
         * be sent to the PHY for "marketing".
         */
        __ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
        struct sja1105_private *priv = ds->priv;
        struct sja1105_xmii_params_entry *mii;

        mii = priv->static_config.tables[BLK_IDX_XMII_PARAMS].entries;

        /* include/linux/phylink.h says:
         *     When @state->interface is %PHY_INTERFACE_MODE_NA, phylink
         *     expects the MAC driver to return all supported link modes.
         */
        if (state->interface != PHY_INTERFACE_MODE_NA &&
            sja1105_phy_mode_mismatch(priv, port, state->interface)) {
                bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
                return;
        }

        /* The MAC does not support pause frames, and also doesn't
         * support half-duplex traffic modes.
         */
        phylink_set(mask, Autoneg);
        phylink_set(mask, MII);
        phylink_set(mask, 10baseT_Full);
        phylink_set(mask, 100baseT_Full);
        phylink_set(mask, 100baseT1_Full);
        if (mii->xmii_mode[port] == XMII_MODE_RGMII ||
            mii->xmii_mode[port] == XMII_MODE_SGMII)
                phylink_set(mask, 1000baseT_Full);
        if (priv->info->supports_2500basex[port]) {
                phylink_set(mask, 2500baseT_Full);
                phylink_set(mask, 2500baseX_Full);
        }

        bitmap_and(supported, supported, mask, __ETHTOOL_LINK_MODE_MASK_NBITS);
        bitmap_and(state->advertising, state->advertising, mask,
                   __ETHTOOL_LINK_MODE_MASK_NBITS);
}

static int
sja1105_find_static_fdb_entry(struct sja1105_private *priv, int port,
                              const struct sja1105_l2_lookup_entry *requested)
{
        struct sja1105_l2_lookup_entry *l2_lookup;
        struct sja1105_table *table;
        int i;

        table = &priv->static_config.tables[BLK_IDX_L2_LOOKUP];
        l2_lookup = table->entries;

        for (i = 0; i < table->entry_count; i++)
                if (l2_lookup[i].macaddr == requested->macaddr &&
                    l2_lookup[i].vlanid == requested->vlanid &&
                    l2_lookup[i].destports & BIT(port))
                        return i;

        return -1;
}

/* We want FDB entries added statically through the bridge command to persist
 * across switch resets, which are a common thing during normal SJA1105
 * operation. So we have to back them up in the static configuration tables
 * and hence apply them on next static config upload... yay!
 */
static int
sja1105_static_fdb_change(struct sja1105_private *priv, int port,
                          const struct sja1105_l2_lookup_entry *requested,
                          bool keep)
{
        struct sja1105_l2_lookup_entry *l2_lookup;
        struct sja1105_table *table;
        int rc, match;

        table = &priv->static_config.tables[BLK_IDX_L2_LOOKUP];

        match = sja1105_find_static_fdb_entry(priv, port, requested);
        if (match < 0) {
                /* Can't delete a missing entry. */
                if (!keep)
                        return 0;

                /* No match => new entry */
                rc = sja1105_table_resize(table, table->entry_count + 1);
                if (rc)
                        return rc;

                match = table->entry_count - 1;
        }

        /* Assign pointer after the resize (it may be new memory) */
        l2_lookup = table->entries;

        /* We have a match.
         * If the job was to add this FDB entry, it's already done (mostly
         * anyway, since the port forwarding mask may have changed, case in
         * which we update it).
         * Otherwise we have to delete it.
         */
        if (keep) {
                l2_lookup[match] = *requested;
                return 0;
        }

        /* To remove, the strategy is to overwrite the element with
         * the last one, and then reduce the array size by 1
         */
        l2_lookup[match] = l2_lookup[table->entry_count - 1];
        return sja1105_table_resize(table, table->entry_count - 1);
}

/* First-generation switches have a 4-way set associative TCAM that
 * holds the FDB entries. An FDB index spans from 0 to 1023 and is comprised of
 * a "bin" (grouping of 4 entries) and a "way" (an entry within a bin).
 * For the placement of a newly learnt FDB entry, the switch selects the bin
 * based on a hash function, and the way within that bin incrementally.
 */
static int sja1105et_fdb_index(int bin, int way)
{
        return bin * SJA1105ET_FDB_BIN_SIZE + way;
}

static int sja1105et_is_fdb_entry_in_bin(struct sja1105_private *priv, int bin,
                                         const u8 *addr, u16 vid,
                                         struct sja1105_l2_lookup_entry *match,
                                         int *last_unused)
{
        int way;

        for (way = 0; way < SJA1105ET_FDB_BIN_SIZE; way++) {
                struct sja1105_l2_lookup_entry l2_lookup = {0};
                int index = sja1105et_fdb_index(bin, way);

                /* Skip unused entries, optionally marking them
                 * into the return value
                 */
                if (sja1105_dynamic_config_read(priv, BLK_IDX_L2_LOOKUP,
                                                index, &l2_lookup)) {
                        if (last_unused)
                                *last_unused = way;
                        continue;
                }

                if (l2_lookup.macaddr == ether_addr_to_u64(addr) &&
                    l2_lookup.vlanid == vid) {
                        if (match)
                                *match = l2_lookup;
                        return way;
                }
        }
        /* Return an invalid entry index if not found */
        return -1;
}

int sja1105et_fdb_add(struct dsa_switch *ds, int port,
                      const unsigned char *addr, u16 vid)
{
        struct sja1105_l2_lookup_entry l2_lookup = {0};
        struct sja1105_private *priv = ds->priv;
        struct device *dev = ds->dev;
        int last_unused = -1;
        int bin, way, rc;

        bin = sja1105et_fdb_hash(priv, addr, vid);

        way = sja1105et_is_fdb_entry_in_bin(priv, bin, addr, vid,
                                            &l2_lookup, &last_unused);
        if (way >= 0) {
                /* We have an FDB entry. Is our port in the destination
                 * mask? If yes, we need to do nothing. If not, we need
                 * to rewrite the entry by adding this port to it.
                 */
                if (l2_lookup.destports & BIT(port))
                        return 0;
                l2_lookup.destports |= BIT(port);
        } else {
                int index = sja1105et_fdb_index(bin, way);

                /* We don't have an FDB entry. We construct a new one and
                 * try to find a place for it within the FDB table.
                 */
                l2_lookup.macaddr = ether_addr_to_u64(addr);
                l2_lookup.destports = BIT(port);
                l2_lookup.vlanid = vid;

                if (last_unused >= 0) {
                        way = last_unused;
                } else {
                        /* Bin is full, need to evict somebody.
                         * Choose victim at random. If you get these messages
                         * often, you may need to consider changing the
                         * distribution function:
                         * static_config[BLK_IDX_L2_LOOKUP_PARAMS].entries->poly
                         */
                        get_random_bytes(&way, sizeof(u8));
                        way %= SJA1105ET_FDB_BIN_SIZE;
                        dev_warn(dev, "Warning, FDB bin %d full while adding entry for %pM. Evicting entry %u.\n",
                                 bin, addr, way);
                        /* Evict entry */
                        sja1105_dynamic_config_write(priv, BLK_IDX_L2_LOOKUP,
                                                     index, NULL, false);
                }
        }
        l2_lookup.index = sja1105et_fdb_index(bin, way);

        rc = sja1105_dynamic_config_write(priv, BLK_IDX_L2_LOOKUP,
                                          l2_lookup.index, &l2_lookup,
                                          true);
        if (rc < 0)
                return rc;

        return sja1105_static_fdb_change(priv, port, &l2_lookup, true);
}

int sja1105et_fdb_del(struct dsa_switch *ds, int port,
                      const unsigned char *addr, u16 vid)
{
        struct sja1105_l2_lookup_entry l2_lookup = {0};
        struct sja1105_private *priv = ds->priv;
        int index, bin, way, rc;
        bool keep;

        bin = sja1105et_fdb_hash(priv, addr, vid);
        way = sja1105et_is_fdb_entry_in_bin(priv, bin, addr, vid,
                                            &l2_lookup, NULL);
        if (way < 0)
                return 0;
        index = sja1105et_fdb_index(bin, way);

        /* We have an FDB entry. Is our port in the destination mask? If yes,
         * we need to remove it. If the resulting port mask becomes empty, we
         * need to completely evict the FDB entry.
         * Otherwise we just write it back.
         */
        l2_lookup.destports &= ~BIT(port);

        if (l2_lookup.destports)
                keep = true;
        else
                keep = false;

        rc = sja1105_dynamic_config_write(priv, BLK_IDX_L2_LOOKUP,
                                          index, &l2_lookup, keep);
        if (rc < 0)
                return rc;

        return sja1105_static_fdb_change(priv, port, &l2_lookup, keep);
}

int sja1105pqrs_fdb_add(struct dsa_switch *ds, int port,
                        const unsigned char *addr, u16 vid)
{
        struct sja1105_l2_lookup_entry l2_lookup = {0};
        struct sja1105_private *priv = ds->priv;
        int rc, i;

        /* Search for an existing entry in the FDB table */
        l2_lookup.macaddr = ether_addr_to_u64(addr);
        l2_lookup.vlanid = vid;
        l2_lookup.iotag = SJA1105_S_TAG;
        l2_lookup.mask_macaddr = GENMASK_ULL(ETH_ALEN * 8 - 1, 0);
        if (priv->vlan_state != SJA1105_VLAN_UNAWARE) {
                l2_lookup.mask_vlanid = VLAN_VID_MASK;
                l2_lookup.mask_iotag = BIT(0);
        } else {
                l2_lookup.mask_vlanid = 0;
                l2_lookup.mask_iotag = 0;
        }
        l2_lookup.destports = BIT(port);

        rc = sja1105_dynamic_config_read(priv, BLK_IDX_L2_LOOKUP,
                                         SJA1105_SEARCH, &l2_lookup);
        if (rc == 0) {
                /* Found and this port is already in the entry's
                 * port mask => job done
                 */
                if (l2_lookup.destports & BIT(port))
                        return 0;
                /* l2_lookup.index is populated by the switch in case it
                 * found something.
                 */
                l2_lookup.destports |= BIT(port);
                goto skip_finding_an_index;
        }

        /* Not found, so try to find an unused spot in the FDB.
         * This is slightly inefficient because the strategy is knock-knock at
         * every possible position from 0 to 1023.
         */
        for (i = 0; i < SJA1105_MAX_L2_LOOKUP_COUNT; i++) {
                rc = sja1105_dynamic_config_read(priv, BLK_IDX_L2_LOOKUP,
                                                 i, NULL);
                if (rc < 0)
                        break;
        }
        if (i == SJA1105_MAX_L2_LOOKUP_COUNT) {
                dev_err(ds->dev, "FDB is full, cannot add entry.\n");
                return -EINVAL;
        }
        l2_lookup.lockeds = true;
        l2_lookup.index = i;

skip_finding_an_index:
        rc = sja1105_dynamic_config_write(priv, BLK_IDX_L2_LOOKUP,
                                          l2_lookup.index, &l2_lookup,
                                          true);
        if (rc < 0)
                return rc;

        return sja1105_static_fdb_change(priv, port, &l2_lookup, true);
}

int sja1105pqrs_fdb_del(struct dsa_switch *ds, int port,
                        const unsigned char *addr, u16 vid)
{
        struct sja1105_l2_lookup_entry l2_lookup = {0};
        struct sja1105_private *priv = ds->priv;
        bool keep;
        int rc;

        l2_lookup.macaddr = ether_addr_to_u64(addr);
        l2_lookup.vlanid = vid;
        l2_lookup.iotag = SJA1105_S_TAG;
        l2_lookup.mask_macaddr = GENMASK_ULL(ETH_ALEN * 8 - 1, 0);
        if (priv->vlan_state != SJA1105_VLAN_UNAWARE) {
                l2_lookup.mask_vlanid = VLAN_VID_MASK;
                l2_lookup.mask_iotag = BIT(0);
        } else {
                l2_lookup.mask_vlanid = 0;
                l2_lookup.mask_iotag = 0;
        }
        l2_lookup.destports = BIT(port);

        rc = sja1105_dynamic_config_read(priv, BLK_IDX_L2_LOOKUP,
                                         SJA1105_SEARCH, &l2_lookup);
        if (rc < 0)
                return 0;

        l2_lookup.destports &= ~BIT(port);

        /* Decide whether we remove just this port from the FDB entry,
         * or if we remove it completely.
         */
        if (l2_lookup.destports)
                keep = true;
        else
                keep = false;

        rc = sja1105_dynamic_config_write(priv, BLK_IDX_L2_LOOKUP,
                                          l2_lookup.index, &l2_lookup, keep);
        if (rc < 0)
                return rc;

        return sja1105_static_fdb_change(priv, port, &l2_lookup, keep);
}

static int sja1105_fdb_add(struct dsa_switch *ds, int port,
                           const unsigned char *addr, u16 vid)
{
        struct sja1105_private *priv = ds->priv;

        /* dsa_8021q is in effect when the bridge's vlan_filtering isn't,
         * so the switch still does some VLAN processing internally.
         * But Shared VLAN Learning (SVL) is also active, and it will take
         * care of autonomous forwarding between the unique pvid's of each
         * port.  Here we just make sure that users can't add duplicate FDB
         * entries when in this mode - the actual VID doesn't matter except
         * for what gets printed in 'bridge fdb show'.  In the case of zero,
         * no VID gets printed at all.
         */
        if (priv->vlan_state != SJA1105_VLAN_FILTERING_FULL)
                vid = 0;

        return priv->info->fdb_add_cmd(ds, port, addr, vid);
}

static int sja1105_fdb_del(struct dsa_switch *ds, int port,
                           const unsigned char *addr, u16 vid)
{
        struct sja1105_private *priv = ds->priv;

        if (priv->vlan_state != SJA1105_VLAN_FILTERING_FULL)
                vid = 0;

        return priv->info->fdb_del_cmd(ds, port, addr, vid);
}

static int sja1105_fdb_dump(struct dsa_switch *ds, int port,
                            dsa_fdb_dump_cb_t *cb, void *data)
{
        struct sja1105_private *priv = ds->priv;
        struct device *dev = ds->dev;
        int i;

        for (i = 0; i < SJA1105_MAX_L2_LOOKUP_COUNT; i++) {
                struct sja1105_l2_lookup_entry l2_lookup = {0};
                u8 macaddr[ETH_ALEN];
                int rc;

                rc = sja1105_dynamic_config_read(priv, BLK_IDX_L2_LOOKUP,
                                                 i, &l2_lookup);
                /* No fdb entry at i, not an issue */
                if (rc == -ENOENT)
                        continue;
                if (rc) {
                        dev_err(dev, "Failed to dump FDB: %d\n", rc);
                        return rc;
                }

                /* FDB dump callback is per port. This means we have to
                 * disregard a valid entry if it's not for this port, even if
                 * only to revisit it later. This is inefficient because the
                 * 1024-sized FDB table needs to be traversed 4 times through
                 * SPI during a 'bridge fdb show' command.
                 */
                if (!(l2_lookup.destports & BIT(port)))
                        continue;

                /* We need to hide the FDB entry for unknown multicast */
                if (l2_lookup.macaddr == SJA1105_UNKNOWN_MULTICAST &&
                    l2_lookup.mask_macaddr == SJA1105_UNKNOWN_MULTICAST)
                        continue;

                u64_to_ether_addr(l2_lookup.macaddr, macaddr);

                /* We need to hide the dsa_8021q VLANs from the user. */
                if (priv->vlan_state == SJA1105_VLAN_UNAWARE)
                        l2_lookup.vlanid = 0;
                cb(macaddr, l2_lookup.vlanid, l2_lookup.lockeds, data);
        }
        return 0;
}

static int sja1105_mdb_add(struct dsa_switch *ds, int port,
                           const struct switchdev_obj_port_mdb *mdb)
{
        return sja1105_fdb_add(ds, port, mdb->addr, mdb->vid);
}

static int sja1105_mdb_del(struct dsa_switch *ds, int port,
                           const struct switchdev_obj_port_mdb *mdb)
{
        return sja1105_fdb_del(ds, port, mdb->addr, mdb->vid);
}

/* Common function for unicast and broadcast flood configuration.
 * Flooding is configured between each {ingress, egress} port pair, and since
 * the bridge's semantics are those of "egress flooding", it means we must
 * enable flooding towards this port from all ingress ports that are in the
 * same forwarding domain.
 */
static int sja1105_manage_flood_domains(struct sja1105_private *priv)
{
        struct sja1105_l2_forwarding_entry *l2_fwd;
        struct dsa_switch *ds = priv->ds;
        int from, to, rc;

        l2_fwd = priv->static_config.tables[BLK_IDX_L2_FORWARDING].entries;

        for (from = 0; from < ds->num_ports; from++) {
                u64 fl_domain = 0, bc_domain = 0;

                for (to = 0; to < priv->ds->num_ports; to++) {
                        if (!sja1105_can_forward(l2_fwd, from, to))
                                continue;

                        if (priv->ucast_egress_floods & BIT(to))
                                fl_domain |= BIT(to);
                        if (priv->bcast_egress_floods & BIT(to))
                                bc_domain |= BIT(to);
                }

                /* Nothing changed, nothing to do */
                if (l2_fwd[from].fl_domain == fl_domain &&
                    l2_fwd[from].bc_domain == bc_domain)
                        continue;

                l2_fwd[from].fl_domain = fl_domain;
                l2_fwd[from].bc_domain = bc_domain;

                rc = sja1105_dynamic_config_write(priv, BLK_IDX_L2_FORWARDING,
                                                  from, &l2_fwd[from], true);
                if (rc < 0)
                        return rc;
        }

        return 0;
}

static int sja1105_bridge_member(struct dsa_switch *ds, int port,
                                 struct net_device *br, bool member)
{
        struct sja1105_l2_forwarding_entry *l2_fwd;
        struct sja1105_private *priv = ds->priv;
        int i, rc;

        l2_fwd = priv->static_config.tables[BLK_IDX_L2_FORWARDING].entries;

        for (i = 0; i < ds->num_ports; i++) {
                /* Add this port to the forwarding matrix of the
                 * other ports in the same bridge, and viceversa.
                 */
                if (!dsa_is_user_port(ds, i))
                        continue;
                /* For the ports already under the bridge, only one thing needs
                 * to be done, and that is to add this port to their
                 * reachability domain. So we can perform the SPI write for
                 * them immediately. However, for this port itself (the one
                 * that is new to the bridge), we need to add all other ports
                 * to its reachability domain. So we do that incrementally in
                 * this loop, and perform the SPI write only at the end, once
                 * the domain contains all other bridge ports.
                 */
                if (i == port)
                        continue;
                if (dsa_to_port(ds, i)->bridge_dev != br)
                        continue;
                sja1105_port_allow_traffic(l2_fwd, i, port, member);
                sja1105_port_allow_traffic(l2_fwd, port, i, member);

                rc = sja1105_dynamic_config_write(priv, BLK_IDX_L2_FORWARDING,
                                                  i, &l2_fwd[i], true);
                if (rc < 0)
                        return rc;
        }

        rc = sja1105_dynamic_config_write(priv, BLK_IDX_L2_FORWARDING,
                                          port, &l2_fwd[port], true);
        if (rc)
                return rc;

        return sja1105_manage_flood_domains(priv);
}

static void sja1105_bridge_stp_state_set(struct dsa_switch *ds, int port,
                                         u8 state)
{
        struct sja1105_private *priv = ds->priv;
        struct sja1105_mac_config_entry *mac;

        mac = priv->static_config.tables[BLK_IDX_MAC_CONFIG].entries;

        switch (state) {
        case BR_STATE_DISABLED:
        case BR_STATE_BLOCKING:
                /* From UM10944 description of DRPDTAG (why put this there?):
                 * "Management traffic flows to the port regardless of the state
                 * of the INGRESS flag". So BPDUs are still be allowed to pass.
                 * At the moment no difference between DISABLED and BLOCKING.
                 */
                mac[port].ingress   = false;
                mac[port].egress    = false;
                mac[port].dyn_learn = false;
                break;
        case BR_STATE_LISTENING:
                mac[port].ingress   = true;
                mac[port].egress    = false;
                mac[port].dyn_learn = false;
                break;
        case BR_STATE_LEARNING:
                mac[port].ingress   = true;
                mac[port].egress    = false;
                mac[port].dyn_learn = !!(priv->learn_ena & BIT(port));
                break;
        case BR_STATE_FORWARDING:
                mac[port].ingress   = true;
                mac[port].egress    = true;
                mac[port].dyn_learn = !!(priv->learn_ena & BIT(port));
                break;
        default:
                dev_err(ds->dev, "invalid STP state: %d\n", state);
                return;
        }

        sja1105_dynamic_config_write(priv, BLK_IDX_MAC_CONFIG, port,
                                     &mac[port], true);
}

static int sja1105_bridge_join(struct dsa_switch *ds, int port,
                               struct net_device *br)
{
        return sja1105_bridge_member(ds, port, br, true);
}

static void sja1105_bridge_leave(struct dsa_switch *ds, int port,
                                 struct net_device *br)
{
        sja1105_bridge_member(ds, port, br, false);
}

#define BYTES_PER_KBIT (1000LL / 8)

static int sja1105_find_unused_cbs_shaper(struct sja1105_private *priv)
{
        int i;

        for (i = 0; i < priv->info->num_cbs_shapers; i++)
                if (!priv->cbs[i].idle_slope && !priv->cbs[i].send_slope)
                        return i;

        return -1;
}

static int sja1105_delete_cbs_shaper(struct sja1105_private *priv, int port,
                                     int prio)
{
        int i;

        for (i = 0; i < priv->info->num_cbs_shapers; i++) {
                struct sja1105_cbs_entry *cbs = &priv->cbs[i];

                if (cbs->port == port && cbs->prio == prio) {
                        memset(cbs, 0, sizeof(*cbs));
                        return sja1105_dynamic_config_write(priv, BLK_IDX_CBS,
                                                            i, cbs, true);
                }
        }

        return 0;
}

static int sja1105_setup_tc_cbs(struct dsa_switch *ds, int port,
                                struct tc_cbs_qopt_offload *offload)
{
        struct sja1105_private *priv = ds->priv;
        struct sja1105_cbs_entry *cbs;
        int index;

        if (!offload->enable)
                return sja1105_delete_cbs_shaper(priv, port, offload->queue);

        index = sja1105_find_unused_cbs_shaper(priv);
        if (index < 0)
                return -ENOSPC;

        cbs = &priv->cbs[index];
        cbs->port = port;
        cbs->prio = offload->queue;
        /* locredit and sendslope are negative by definition. In hardware,
         * positive values must be provided, and the negative sign is implicit.
         */
        cbs->credit_hi = offload->hicredit;
        cbs->credit_lo = abs(offload->locredit);
        /* User space is in kbits/sec, hardware in bytes/sec */
        cbs->idle_slope = offload->idleslope * BYTES_PER_KBIT;
        cbs->send_slope = abs(offload->sendslope * BYTES_PER_KBIT);
        /* Convert the negative values from 64-bit 2's complement
         * to 32-bit 2's complement (for the case of 0x80000000 whose
         * negative is still negative).
         */
        cbs->credit_lo &= GENMASK_ULL(31, 0);
        cbs->send_slope &= GENMASK_ULL(31, 0);

        return sja1105_dynamic_config_write(priv, BLK_IDX_CBS, index, cbs,
                                            true);
}

static int sja1105_reload_cbs(struct sja1105_private *priv)
{
        int rc = 0, i;

        /* The credit based shapers are only allocated if
         * CONFIG_NET_SCH_CBS is enabled.
         */
        if (!priv->cbs)
                return 0;

        for (i = 0; i < priv->info->num_cbs_shapers; i++) {
                struct sja1105_cbs_entry *cbs = &priv->cbs[i];

                if (!cbs->idle_slope && !cbs->send_slope)
                        continue;

                rc = sja1105_dynamic_config_write(priv, BLK_IDX_CBS, i, cbs,
                                                  true);
                if (rc)
                        break;
        }

        return rc;
}

static const char * const sja1105_reset_reasons[] = {
        [SJA1105_VLAN_FILTERING] = "VLAN filtering",
        [SJA1105_RX_HWTSTAMPING] = "RX timestamping",
        [SJA1105_AGEING_TIME] = "Ageing time",
        [SJA1105_SCHEDULING] = "Time-aware scheduling",
        [SJA1105_BEST_EFFORT_POLICING] = "Best-effort policing",
        [SJA1105_VIRTUAL_LINKS] = "Virtual links",
};

/* For situations where we need to change a setting at runtime that is only
 * available through the static configuration, resetting the switch in order
 * to upload the new static config is unavoidable. Back up the settings we
 * modify at runtime (currently only MAC) and restore them after uploading,
 * such that this operation is relatively seamless.
 */
int sja1105_static_config_reload(struct sja1105_private *priv,
                                 enum sja1105_reset_reason reason)
{
        struct ptp_system_timestamp ptp_sts_before;
        struct ptp_system_timestamp ptp_sts_after;
        int speed_mbps[SJA1105_MAX_NUM_PORTS];
        u16 bmcr[SJA1105_MAX_NUM_PORTS] = {0};
        struct sja1105_mac_config_entry *mac;
        struct dsa_switch *ds = priv->ds;
        s64 t1, t2, t3, t4;
        s64 t12, t34;
        int rc, i;
        s64 now;

        mutex_lock(&priv->mgmt_lock);

        mac = priv->static_config.tables[BLK_IDX_MAC_CONFIG].entries;

        /* Back up the dynamic link speed changed by sja1105_adjust_port_config
         * in order to temporarily restore it to SJA1105_SPEED_AUTO - which the
         * switch wants to see in the static config in order to allow us to
         * change it through the dynamic interface later.
         */
        for (i = 0; i < ds->num_ports; i++) {
                u32 reg_addr = mdiobus_c45_addr(MDIO_MMD_VEND2, MDIO_CTRL1);

                speed_mbps[i] = sja1105_port_speed_to_ethtool(priv,
                                                              mac[i].speed);
                mac[i].speed = priv->info->port_speed[SJA1105_SPEED_AUTO];

                if (priv->xpcs[i])
                        bmcr[i] = mdiobus_read(priv->mdio_pcs, i, reg_addr);
        }

        /* No PTP operations can run right now */
        mutex_lock(&priv->ptp_data.lock);

        rc = __sja1105_ptp_gettimex(ds, &now, &ptp_sts_before);
        if (rc < 0) {
                mutex_unlock(&priv->ptp_data.lock);
                goto out;
        }

        /* Reset switch and send updated static configuration */
        rc = sja1105_static_config_upload(priv);
        if (rc < 0) {
                mutex_unlock(&priv->ptp_data.lock);
                goto out;
        }

        rc = __sja1105_ptp_settime(ds, 0, &ptp_sts_after);
        if (rc < 0) {
                mutex_unlock(&priv->ptp_data.lock);
                goto out;
        }

        t1 = timespec64_to_ns(&ptp_sts_before.pre_ts);
        t2 = timespec64_to_ns(&ptp_sts_before.post_ts);
        t3 = timespec64_to_ns(&ptp_sts_after.pre_ts);
        t4 = timespec64_to_ns(&ptp_sts_after.post_ts);
        /* Mid point, corresponds to pre-reset PTPCLKVAL */
        t12 = t1 + (t2 - t1) / 2;
        /* Mid point, corresponds to post-reset PTPCLKVAL, aka 0 */
        t34 = t3 + (t4 - t3) / 2;
        /* Advance PTPCLKVAL by the time it took since its readout */
        now += (t34 - t12);

        __sja1105_ptp_adjtime(ds, now);

        mutex_unlock(&priv->ptp_data.lock);

        dev_info(priv->ds->dev,
                 "Reset switch and programmed static config. Reason: %s\n",
                 sja1105_reset_reasons[reason]);

        /* Configure the CGU (PLLs) for MII and RMII PHYs.
         * For these interfaces there is no dynamic configuration
         * needed, since PLLs have same settings at all speeds.
         */
        if (priv->info->clocking_setup) {
                rc = priv->info->clocking_setup(priv);
                if (rc < 0)
                        goto out;
        }

        for (i = 0; i < ds->num_ports; i++) {
                struct dw_xpcs *xpcs = priv->xpcs[i];
                unsigned int mode;

                rc = sja1105_adjust_port_config(priv, i, speed_mbps[i]);
                if (rc < 0)
                        goto out;

                if (!xpcs)
                        continue;

                if (bmcr[i] & BMCR_ANENABLE)
                        mode = MLO_AN_INBAND;
                else if (priv->fixed_link[i])
                        mode = MLO_AN_FIXED;
                else
                        mode = MLO_AN_PHY;

                rc = xpcs_do_config(xpcs, priv->phy_mode[i], mode);
                if (rc < 0)
                        goto out;

                if (!phylink_autoneg_inband(mode)) {
                        int speed = SPEED_UNKNOWN;

                        if (priv->phy_mode[i] == PHY_INTERFACE_MODE_2500BASEX)
                                speed = SPEED_2500;
                        else if (bmcr[i] & BMCR_SPEED1000)
                                speed = SPEED_1000;
                        else if (bmcr[i] & BMCR_SPEED100)
                                speed = SPEED_100;
                        else
                                speed = SPEED_10;

                        xpcs_link_up(&xpcs->pcs, mode, priv->phy_mode[i],
                                     speed, DUPLEX_FULL);
                }
        }

        rc = sja1105_reload_cbs(priv);
        if (rc < 0)
                goto out;
out:
        mutex_unlock(&priv->mgmt_lock);

        return rc;
}

static int sja1105_pvid_apply(struct sja1105_private *priv, int port, u16 pvid)
{
        struct sja1105_mac_config_entry *mac;

        mac = priv->static_config.tables[BLK_IDX_MAC_CONFIG].entries;

        mac[port].vlanid = pvid;

        return sja1105_dynamic_config_write(priv, BLK_IDX_MAC_CONFIG, port,
                                           &mac[port], true);
}

static int sja1105_crosschip_bridge_join(struct dsa_switch *ds,
                                         int tree_index, int sw_index,
                                         int other_port, struct net_device *br)
{
        struct dsa_switch *other_ds = dsa_switch_find(tree_index, sw_index);
        struct sja1105_private *other_priv = other_ds->priv;
        struct sja1105_private *priv = ds->priv;
        int port, rc;

        if (other_ds->ops != &sja1105_switch_ops)
                return 0;

        for (port = 0; port < ds->num_ports; port++) {
                if (!dsa_is_user_port(ds, port))
                        continue;
                if (dsa_to_port(ds, port)->bridge_dev != br)
                        continue;

                rc = dsa_8021q_crosschip_bridge_join(priv->dsa_8021q_ctx,
                                                     port,
                                                     other_priv->dsa_8021q_ctx,
                                                     other_port);
                if (rc)
                        return rc;

                rc = dsa_8021q_crosschip_bridge_join(other_priv->dsa_8021q_ctx,
                                                     other_port,
                                                     priv->dsa_8021q_ctx,
                                                     port);
                if (rc)
                        return rc;
        }

        return 0;
}

static void sja1105_crosschip_bridge_leave(struct dsa_switch *ds,
                                           int tree_index, int sw_index,
                                           int other_port,
                                           struct net_device *br)
{
        struct dsa_switch *other_ds = dsa_switch_find(tree_index, sw_index);
        struct sja1105_private *other_priv = other_ds->priv;
        struct sja1105_private *priv = ds->priv;
        int port;

        if (other_ds->ops != &sja1105_switch_ops)
                return;

        for (port = 0; port < ds->num_ports; port++) {
                if (!dsa_is_user_port(ds, port))
                        continue;
                if (dsa_to_port(ds, port)->bridge_dev != br)
                        continue;

                dsa_8021q_crosschip_bridge_leave(priv->dsa_8021q_ctx, port,
                                                 other_priv->dsa_8021q_ctx,
                                                 other_port);

                dsa_8021q_crosschip_bridge_leave(other_priv->dsa_8021q_ctx,
                                                 other_port,
                                                 priv->dsa_8021q_ctx, port);
        }
}

static int sja1105_setup_8021q_tagging(struct dsa_switch *ds, bool enabled)
{
        struct sja1105_private *priv = ds->priv;
        int rc;

        rc = dsa_8021q_setup(priv->dsa_8021q_ctx, enabled);
        if (rc)
                return rc;

        dev_info(ds->dev, "%s switch tagging\n",
                 enabled ? "Enabled" : "Disabled");
        return 0;
}

static enum dsa_tag_protocol
sja1105_get_tag_protocol(struct dsa_switch *ds, int port,
                         enum dsa_tag_protocol mp)
{
        struct sja1105_private *priv = ds->priv;

        return priv->info->tag_proto;
}

static int sja1105_find_free_subvlan(u16 *subvlan_map, bool pvid)
{
        int subvlan;

        if (pvid)
                return 0;

        for (subvlan = 1; subvlan < DSA_8021Q_N_SUBVLAN; subvlan++)
                if (subvlan_map[subvlan] == VLAN_N_VID)
                        return subvlan;

        return -1;
}

static int sja1105_find_subvlan(u16 *subvlan_map, u16 vid)
{
        int subvlan;

        for (subvlan = 0; subvlan < DSA_8021Q_N_SUBVLAN; subvlan++)
                if (subvlan_map[subvlan] == vid)
                        return subvlan;

        return -1;
}

static int sja1105_find_committed_subvlan(struct sja1105_private *priv,
                                          int port, u16 vid)
{
        struct sja1105_port *sp = &priv->ports[port];

        return sja1105_find_subvlan(sp->subvlan_map, vid);
}

static void sja1105_init_subvlan_map(u16 *subvlan_map)
{
        int subvlan;

        for (subvlan = 0; subvlan < DSA_8021Q_N_SUBVLAN; subvlan++)
                subvlan_map[subvlan] = VLAN_N_VID;
}

static void sja1105_commit_subvlan_map(struct sja1105_private *priv, int port,
                                       u16 *subvlan_map)
{
        struct sja1105_port *sp = &priv->ports[port];
        int subvlan;

        for (subvlan = 0; subvlan < DSA_8021Q_N_SUBVLAN; subvlan++)
                sp->subvlan_map[subvlan] = subvlan_map[subvlan];
}

static int sja1105_is_vlan_configured(struct sja1105_private *priv, u16 vid)
{
        struct sja1105_vlan_lookup_entry *vlan;
        int count, i;

        vlan = priv->static_config.tables[BLK_IDX_VLAN_LOOKUP].entries;
        count = priv->static_config.tables[BLK_IDX_VLAN_LOOKUP].entry_count;

        for (i = 0; i < count; i++)
                if (vlan[i].vlanid == vid)
                        return i;

        /* Return an invalid entry index if not found */
        return -1;
}

static int
sja1105_find_retagging_entry(struct sja1105_retagging_entry *retagging,
                             int count, int from_port, u16 from_vid,
                             u16 to_vid)
{
        int i;

        for (i = 0; i < count; i++)
                if (retagging[i].ing_port == BIT(from_port) &&
                    retagging[i].vlan_ing == from_vid &&
                    retagging[i].vlan_egr == to_vid)
                        return i;

        /* Return an invalid entry index if not found */
        return -1;
}

static int sja1105_commit_vlans(struct sja1105_private *priv,
                                struct sja1105_vlan_lookup_entry *new_vlan,
                                struct sja1105_retagging_entry *new_retagging,
                                int num_retagging)
{
        struct sja1105_retagging_entry *retagging;
        struct sja1105_vlan_lookup_entry *vlan;
        struct sja1105_table *table;
        int num_vlans = 0;
        int rc, i, k = 0;

        /* VLAN table */
        table = &priv->static_config.tables[BLK_IDX_VLAN_LOOKUP];
        vlan = table->entries;

        for (i = 0; i < VLAN_N_VID; i++) {
                int match = sja1105_is_vlan_configured(priv, i);

                if (new_vlan[i].vlanid != VLAN_N_VID)
                        num_vlans++;

                if (new_vlan[i].vlanid == VLAN_N_VID && match >= 0) {
                        /* Was there before, no longer is. Delete */
                        dev_dbg(priv->ds->dev, "Deleting VLAN %d\n", i);
                        rc = sja1105_dynamic_config_write(priv,
                                                          BLK_IDX_VLAN_LOOKUP,
                                                          i, &vlan[match], false);
                        if (rc < 0)
                                return rc;
                } else if (new_vlan[i].vlanid != VLAN_N_VID) {
                        /* Nothing changed, don't do anything */
                        if (match >= 0 &&
                            vlan[match].vlanid == new_vlan[i].vlanid &&
                            vlan[match].tag_port == new_vlan[i].tag_port &&
                            vlan[match].vlan_bc == new_vlan[i].vlan_bc &&
                            vlan[match].vmemb_port == new_vlan[i].vmemb_port)
                                continue;
                        /* Update entry */
                        dev_dbg(priv->ds->dev, "Updating VLAN %d\n", i);
                        rc = sja1105_dynamic_config_write(priv,
                                                          BLK_IDX_VLAN_LOOKUP,
                                                          i, &new_vlan[i],
                                                          true);
                        if (rc < 0)
                                return rc;
                }
        }

        if (table->entry_count)
                kfree(table->entries);

        table->entries = kcalloc(num_vlans, table->ops->unpacked_entry_size,
                                 GFP_KERNEL);
        if (!table->entries)
                return -ENOMEM;

        table->entry_count = num_vlans;
        vlan = table->entries;

        for (i = 0; i < VLAN_N_VID; i++) {
                if (new_vlan[i].vlanid == VLAN_N_VID)
                        continue;
                vlan[k++] = new_vlan[i];
        }

        /* VLAN Retagging Table */
        table = &priv->static_config.tables[BLK_IDX_RETAGGING];
        retagging = table->entries;

        for (i = 0; i < table->entry_count; i++) {
                rc = sja1105_dynamic_config_write(priv, BLK_IDX_RETAGGING,
                                                  i, &retagging[i], false);
                if (rc)
                        return rc;
        }

        if (table->entry_count)
                kfree(table->entries);

        table->entries = kcalloc(num_retagging, table->ops->unpacked_entry_size,
                                 GFP_KERNEL);
        if (!table->entries)
                return -ENOMEM;

        table->entry_count = num_retagging;
        retagging = table->entries;

        for (i = 0; i < num_retagging; i++) {
                retagging[i] = new_retagging[i];

                /* Update entry */
                rc = sja1105_dynamic_config_write(priv, BLK_IDX_RETAGGING,
                                                  i, &retagging[i], true);
                if (rc < 0)
                        return rc;
        }

        return 0;
}

struct sja1105_crosschip_vlan {
        struct list_head list;
        u16 vid;
        bool untagged;
        int port;
        int other_port;
        struct dsa_8021q_context *other_ctx;
};

struct sja1105_crosschip_switch {
        struct list_head list;
        struct dsa_8021q_context *other_ctx;
};

static int sja1105_commit_pvid(struct sja1105_private *priv)
{
        struct sja1105_bridge_vlan *v;
        struct list_head *vlan_list;
        int rc = 0;

        if (priv->vlan_state == SJA1105_VLAN_FILTERING_FULL)
                vlan_list = &priv->bridge_vlans;
        else
                vlan_list = &priv->dsa_8021q_vlans;

        list_for_each_entry(v, vlan_list, list) {
                if (v->pvid) {
                        rc = sja1105_pvid_apply(priv, v->port, v->vid);
                        if (rc)
                                break;
                }
        }

        return rc;
}

static int
sja1105_build_bridge_vlans(struct sja1105_private *priv,
                           struct sja1105_vlan_lookup_entry *new_vlan)
{
        struct sja1105_bridge_vlan *v;

        if (priv->vlan_state == SJA1105_VLAN_UNAWARE)
                return 0;

        list_for_each_entry(v, &priv->bridge_vlans, list) {
                int match = v->vid;

                new_vlan[match].vlanid = v->vid;
                new_vlan[match].vmemb_port |= BIT(v->port);
                new_vlan[match].vlan_bc |= BIT(v->port);
                if (!v->untagged)
                        new_vlan[match].tag_port |= BIT(v->port);
                new_vlan[match].type_entry = SJA1110_VLAN_D_TAG;
        }

        return 0;
}

static int
sja1105_build_dsa_8021q_vlans(struct sja1105_private *priv,
                              struct sja1105_vlan_lookup_entry *new_vlan)
{
        struct sja1105_bridge_vlan *v;

        if (priv->vlan_state == SJA1105_VLAN_FILTERING_FULL)
                return 0;

        list_for_each_entry(v, &priv->dsa_8021q_vlans, list) {
                int match = v->vid;

                new_vlan[match].vlanid = v->vid;
                new_vlan[match].vmemb_port |= BIT(v->port);
                new_vlan[match].vlan_bc |= BIT(v->port);
                if (!v->untagged)
                        new_vlan[match].tag_port |= BIT(v->port);
                new_vlan[match].type_entry = SJA1110_VLAN_D_TAG;
        }

        return 0;
}

static int sja1105_build_subvlans(struct sja1105_private *priv,
                                  u16 subvlan_map[][DSA_8021Q_N_SUBVLAN],
                                  struct sja1105_vlan_lookup_entry *new_vlan,
                                  struct sja1105_retagging_entry *new_retagging,
                                  int *num_retagging)
{
        struct sja1105_bridge_vlan *v;
        int k = *num_retagging;

        if (priv->vlan_state != SJA1105_VLAN_BEST_EFFORT)
                return 0;

        list_for_each_entry(v, &priv->bridge_vlans, list) {
                int upstream = dsa_upstream_port(priv->ds, v->port);
                int match, subvlan;
                u16 rx_vid;

                /* Only sub-VLANs on user ports need to be applied.
                 * Bridge VLANs also include VLANs added automatically
                 * by DSA on the CPU port.
                 */
                if (!dsa_is_user_port(priv->ds, v->port))
                        continue;

                subvlan = sja1105_find_subvlan(subvlan_map[v->port],
                                               v->vid);
                if (subvlan < 0) {
                        subvlan = sja1105_find_free_subvlan(subvlan_map[v->port],
                                                            v->pvid);
                        if (subvlan < 0) {
                                dev_err(priv->ds->dev, "No more free subvlans\n");
                                return -ENOSPC;
                        }
                }

                rx_vid = dsa_8021q_rx_vid_subvlan(priv->ds, v->port, subvlan);

                /* @v->vid on @v->port needs to be retagged to @rx_vid
                 * on @upstream. Assume @v->vid on @v->port and on
                 * @upstream was already configured by the previous
                 * iteration over bridge_vlans.
                 */
                match = rx_vid;
                new_vlan[match].vlanid = rx_vid;
                new_vlan[match].vmemb_port |= BIT(v->port);
                new_vlan[match].vmemb_port |= BIT(upstream);
                new_vlan[match].vlan_bc |= BIT(v->port);
                new_vlan[match].vlan_bc |= BIT(upstream);
                /* The "untagged" flag is set the same as for the
                 * original VLAN
                 */
                if (!v->untagged)
                        new_vlan[match].tag_port |= BIT(v->port);
                /* But it's always tagged towards the CPU */
                new_vlan[match].tag_port |= BIT(upstream);
                new_vlan[match].type_entry = SJA1110_VLAN_D_TAG;

                /* The Retagging Table generates packet *clones* with
                 * the new VLAN. This is a very odd hardware quirk
                 * which we need to suppress by dropping the original
                 * packet.
                 * Deny egress of the original VLAN towards the CPU
                 * port. This will force the switch to drop it, and
                 * we'll see only the retagged packets.
                 */
                match = v->vid;
                new_vlan[match].vlan_bc &= ~BIT(upstream);

                /* And the retagging itself */
                new_retagging[k].vlan_ing = v->vid;
                new_retagging[k].vlan_egr = rx_vid;
                new_retagging[k].ing_port = BIT(v->port);
                new_retagging[k].egr_port = BIT(upstream);
                if (k++ == SJA1105_MAX_RETAGGING_COUNT) {
                        dev_err(priv->ds->dev, "No more retagging rules\n");
                        return -ENOSPC;
                }

                subvlan_map[v->port][subvlan] = v->vid;
        }

        *num_retagging = k;

        return 0;
}

/* Sadly, in crosschip scenarios where the CPU port is also the link to another
 * switch, we should retag backwards (the dsa_8021q vid to the original vid) on
 * the CPU port of neighbour switches.
 */
static int
sja1105_build_crosschip_subvlans(struct sja1105_private *priv,
                                 struct sja1105_vlan_lookup_entry *new_vlan,
                                 struct sja1105_retagging_entry *new_retagging,
                                 int *num_retagging)
{
        struct sja1105_crosschip_vlan *tmp, *pos;
        struct dsa_8021q_crosschip_link *c;
        struct sja1105_bridge_vlan *v, *w;
        struct list_head crosschip_vlans;
        int k = *num_retagging;
        int rc = 0;

        if (priv->vlan_state != SJA1105_VLAN_BEST_EFFORT)
                return 0;

        INIT_LIST_HEAD(&crosschip_vlans);

        list_for_each_entry(c, &priv->dsa_8021q_ctx->crosschip_links, list) {
                struct sja1105_private *other_priv = c->other_ctx->ds->priv;

                if (other_priv->vlan_state == SJA1105_VLAN_FILTERING_FULL)
                        continue;

                /* Crosschip links are also added to the CPU ports.
                 * Ignore those.
                 */
                if (!dsa_is_user_port(priv->ds, c->port))
                        continue;
                if (!dsa_is_user_port(c->other_ctx->ds, c->other_port))
                        continue;

                /* Search for VLANs on the remote port */
                list_for_each_entry(v, &other_priv->bridge_vlans, list) {
                        bool already_added = false;
                        bool we_have_it = false;

                        if (v->port != c->other_port)
                                continue;

                        /* If @v is a pvid on @other_ds, it does not need
                         * re-retagging, because its SVL field is 0 and we
                         * already allow that, via the dsa_8021q crosschip
                         * links.
                         */
                        if (v->pvid)
                                continue;

                        /* Search for the VLAN on our local port */
                        list_for_each_entry(w, &priv->bridge_vlans, list) {
                                if (w->port == c->port && w->vid == v->vid) {
                                        we_have_it = true;
                                        break;
                                }
                        }

                        if (!we_have_it)
                                continue;

                        list_for_each_entry(tmp, &crosschip_vlans, list) {
                                if (tmp->vid == v->vid &&
                                    tmp->untagged == v->untagged &&
                                    tmp->port == c->port &&
                                    tmp->other_port == v->port &&
                                    tmp->other_ctx == c->other_ctx) {
                                        already_added = true;
                                        break;
                                }
                        }

                        if (already_added)
                                continue;

                        tmp = kzalloc(sizeof(*tmp), GFP_KERNEL);
                        if (!tmp) {
                                dev_err(priv->ds->dev, "Failed to allocate memory\n");
                                rc = -ENOMEM;
                                goto out;
                        }
                        tmp->vid = v->vid;
                        tmp->port = c->port;
                        tmp->other_port = v->port;
                        tmp->other_ctx = c->other_ctx;
                        tmp->untagged = v->untagged;
                        list_add(&tmp->list, &crosschip_vlans);
                }
        }

        list_for_each_entry(tmp, &crosschip_vlans, list) {
                struct sja1105_private *other_priv = tmp->other_ctx->ds->priv;
                int upstream = dsa_upstream_port(priv->ds, tmp->port);
                int match, subvlan;
                u16 rx_vid;

                subvlan = sja1105_find_committed_subvlan(other_priv,
                                                         tmp->other_port,
                                                         tmp->vid);
                /* If this happens, it's a bug. The neighbour switch does not
                 * have a subvlan for tmp->vid on tmp->other_port, but it
                 * should, since we already checked for its vlan_state.
                 */
                if (WARN_ON(subvlan < 0)) {
                        rc = -EINVAL;
                        goto out;
                }

                rx_vid = dsa_8021q_rx_vid_subvlan(tmp->other_ctx->ds,
                                                  tmp->other_port,
                                                  subvlan);

                /* The @rx_vid retagged from @tmp->vid on
                 * {@tmp->other_ds, @tmp->other_port} needs to be
                 * re-retagged to @tmp->vid on the way back to us.
                 *
                 * Assume the original @tmp->vid is already configured
                 * on this local switch, otherwise we wouldn't be
                 * retagging its subvlan on the other switch in the
                 * first place. We just need to add a reverse retagging
                 * rule for @rx_vid and install @rx_vid on our ports.
                 */
                match = rx_vid;
                new_vlan[match].vlanid = rx_vid;
                new_vlan[match].vmemb_port |= BIT(tmp->port);
                new_vlan[match].vmemb_port |= BIT(upstream);
                /* The "untagged" flag is set the same as for the
                 * original VLAN. And towards the CPU, it doesn't
                 * really matter, because @rx_vid will only receive
                 * traffic on that port. For consistency with other dsa_8021q
                 * VLANs, we'll keep the CPU port tagged.
                 */
                if (!tmp->untagged)
                        new_vlan[match].tag_port |= BIT(tmp->port);
                new_vlan[match].tag_port |= BIT(upstream);
                new_vlan[match].type_entry = SJA1110_VLAN_D_TAG;
                /* Deny egress of @rx_vid towards our front-panel port.
                 * This will force the switch to drop it, and we'll see
                 * only the re-retagged packets (having the original,
                 * pre-initial-retagging, VLAN @tmp->vid).
                 */
                new_vlan[match].vlan_bc &= ~BIT(tmp->port);

                /* On reverse retagging, the same ingress VLAN goes to multiple
                 * ports. So we have an opportunity to create composite rules
                 * to not waste the limited space in the retagging table.
                 */
                k = sja1105_find_retagging_entry(new_retagging, *num_retagging,
                                                 upstream, rx_vid, tmp->vid);
                if (k < 0) {
                        if (*num_retagging == SJA1105_MAX_RETAGGING_COUNT) {
                                dev_err(priv->ds->dev, "No more retagging rules\n");
                                rc = -ENOSPC;
                                goto out;
                        }
                        k = (*num_retagging)++;
                }
                /* And the retagging itself */
                new_retagging[k].vlan_ing = rx_vid;
                new_retagging[k].vlan_egr = tmp->vid;
                new_retagging[k].ing_port = BIT(upstream);
                new_retagging[k].egr_port |= BIT(tmp->port);
        }

out:
        list_for_each_entry_safe(tmp, pos, &crosschip_vlans, list) {
                list_del(&tmp->list);
                kfree(tmp);
        }

        return rc;
}

static int sja1105_build_vlan_table(struct sja1105_private *priv, bool notify);

static int sja1105_notify_crosschip_switches(struct sja1105_private *priv)
{
        struct sja1105_crosschip_switch *s, *pos;
        struct list_head crosschip_switches;
        struct dsa_8021q_crosschip_link *c;
        int rc = 0;

        INIT_LIST_HEAD(&crosschip_switches);

        list_for_each_entry(c, &priv->dsa_8021q_ctx->crosschip_links, list) {
                bool already_added = false;

                list_for_each_entry(s, &crosschip_switches, list) {
                        if (s->other_ctx == c->other_ctx) {
                                already_added = true;
                                break;
                        }
                }

                if (already_added)
                        continue;

                s = kzalloc(sizeof(*s), GFP_KERNEL);
                if (!s) {
                        dev_err(priv->ds->dev, "Failed to allocate memory\n");
                        rc = -ENOMEM;
                        goto out;
                }
                s->other_ctx = c->other_ctx;
                list_add(&s->list, &crosschip_switches);
        }

        list_for_each_entry(s, &crosschip_switches, list) {
                struct sja1105_private *other_priv = s->other_ctx->ds->priv;

                rc = sja1105_build_vlan_table(other_priv, false);
                if (rc)
                        goto out;
        }

out:
        list_for_each_entry_safe(s, pos, &crosschip_switches, list) {
                list_del(&s->list);
                kfree(s);
        }

        return rc;
}

static int sja1105_build_vlan_table(struct sja1105_private *priv, bool notify)
{
        u16 subvlan_map[SJA1105_MAX_NUM_PORTS][DSA_8021Q_N_SUBVLAN];
        struct sja1105_retagging_entry *new_retagging;
        struct sja1105_vlan_lookup_entry *new_vlan;
        struct sja1105_table *table;
        int i, num_retagging = 0;
        int rc;

        table = &priv->static_config.tables[BLK_IDX_VLAN_LOOKUP];
        new_vlan = kcalloc(VLAN_N_VID,
                           table->ops->unpacked_entry_size, GFP_KERNEL);
        if (!new_vlan)
                return -ENOMEM;

        table = &priv->static_config.tables[BLK_IDX_VLAN_LOOKUP];
        new_retagging = kcalloc(SJA1105_MAX_RETAGGING_COUNT,
                                table->ops->unpacked_entry_size, GFP_KERNEL);
        if (!new_retagging) {
                kfree(new_vlan);
                return -ENOMEM;
        }

        for (i = 0; i < VLAN_N_VID; i++)
                new_vlan[i].vlanid = VLAN_N_VID;

        for (i = 0; i < SJA1105_MAX_RETAGGING_COUNT; i++)
                new_retagging[i].vlan_ing = VLAN_N_VID;

        for (i = 0; i < priv->ds->num_ports; i++)
                sja1105_init_subvlan_map(subvlan_map[i]);

        /* Bridge VLANs */
        rc = sja1105_build_bridge_vlans(priv, new_vlan);
        if (rc)
                goto out;

        /* VLANs necessary for dsa_8021q operation, given to us by tag_8021q.c:
         * - RX VLANs
         * - TX VLANs
         * - Crosschip links
         */
        rc = sja1105_build_dsa_8021q_vlans(priv, new_vlan);
        if (rc)
                goto out;

        /* Private VLANs necessary for dsa_8021q operation, which we need to
         * determine on our own:
         * - Sub-VLANs
         * - Sub-VLANs of crosschip switches
         */
        rc = sja1105_build_subvlans(priv, subvlan_map, new_vlan, new_retagging,
                                    &num_retagging);
        if (rc)
                goto out;

        rc = sja1105_build_crosschip_subvlans(priv, new_vlan, new_retagging,
                                              &num_retagging);
        if (rc)
                goto out;

        rc = sja1105_commit_vlans(priv, new_vlan, new_retagging, num_retagging);
        if (rc)
                goto out;

        rc = sja1105_commit_pvid(priv);
        if (rc)
                goto out;

        for (i = 0; i < priv->ds->num_ports; i++)
                sja1105_commit_subvlan_map(priv, i, subvlan_map[i]);

        if (notify) {
                rc = sja1105_notify_crosschip_switches(priv);
                if (rc)
                        goto out;
        }

out:
        kfree(new_vlan);
        kfree(new_retagging);

        return rc;
}

/* The TPID setting belongs to the General Parameters table,
 * which can only be partially reconfigured at runtime (and not the TPID).
 * So a switch reset is required.
 */
int sja1105_vlan_filtering(struct dsa_switch *ds, int port, bool enabled,
                           struct netlink_ext_ack *extack)
{
        struct sja1105_l2_lookup_params_entry *l2_lookup_params;
        struct sja1105_general_params_entry *general_params;
        struct sja1105_private *priv = ds->priv;
        enum sja1105_vlan_state state;
        struct sja1105_table *table;
        struct sja1105_rule *rule;
        bool want_tagging;
        u16 tpid, tpid2;
        int rc;

        list_for_each_entry(rule, &priv->flow_block.rules, list) {
                if (rule->type == SJA1105_RULE_VL) {
                        NL_SET_ERR_MSG_MOD(extack,
                                           "Cannot change VLAN filtering with active VL rules");
                        return -EBUSY;
                }
        }

        if (enabled) {
                /* Enable VLAN filtering. */
                tpid  = ETH_P_8021Q;
                tpid2 = ETH_P_8021AD;
        } else {
                /* Disable VLAN filtering. */
                tpid  = ETH_P_SJA1105;
                tpid2 = ETH_P_SJA1105;
        }

        for (port = 0; port < ds->num_ports; port++) {
                struct sja1105_port *sp = &priv->ports[port];

                if (enabled)
                        sp->xmit_tpid = priv->info->qinq_tpid;
                else
                        sp->xmit_tpid = ETH_P_SJA1105;
        }

        if (!enabled)
                state = SJA1105_VLAN_UNAWARE;
        else if (priv->best_effort_vlan_filtering)
                state = SJA1105_VLAN_BEST_EFFORT;
        else
                state = SJA1105_VLAN_FILTERING_FULL;

        if (priv->vlan_state == state)
                return 0;

        priv->vlan_state = state;
        want_tagging = (state == SJA1105_VLAN_UNAWARE ||
                        state == SJA1105_VLAN_BEST_EFFORT);

        table = &priv->static_config.tables[BLK_IDX_GENERAL_PARAMS];
        general_params = table->entries;
        /* EtherType used to identify inner tagged (C-tag) VLAN traffic */
        general_params->tpid = tpid;
        /* EtherType used to identify outer tagged (S-tag) VLAN traffic */
        general_params->tpid2 = tpid2;
        /* When VLAN filtering is on, we need to at least be able to
         * decode management traffic through the "backup plan".
         */
        general_params->incl_srcpt1 = enabled;
        general_params->incl_srcpt0 = enabled;

        want_tagging = priv->best_effort_vlan_filtering || !enabled;

        /* VLAN filtering => independent VLAN learning.
         * No VLAN filtering (or best effort) => shared VLAN learning.
         *
         * In shared VLAN learning mode, untagged traffic still gets
         * pvid-tagged, and the FDB table gets populated with entries
         * containing the "real" (pvid or from VLAN tag) VLAN ID.
         * However the switch performs a masked L2 lookup in the FDB,
         * effectively only looking up a frame's DMAC (and not VID) for the
         * forwarding decision.
         *
         * This is extremely convenient for us, because in modes with
         * vlan_filtering=0, dsa_8021q actually installs unique pvid's into
         * each front panel port. This is good for identification but breaks
         * learning badly - the VID of the learnt FDB entry is unique, aka
         * no frames coming from any other port are going to have it. So
         * for forwarding purposes, this is as though learning was broken
         * (all frames get flooded).
         */
        table = &priv->static_config.tables[BLK_IDX_L2_LOOKUP_PARAMS];
        l2_lookup_params = table->entries;
        l2_lookup_params->shared_learn = want_tagging;

        sja1105_frame_memory_partitioning(priv);

        rc = sja1105_build_vlan_table(priv, false);
        if (rc)
                return rc;

        rc = sja1105_static_config_reload(priv, SJA1105_VLAN_FILTERING);
        if (rc)
                NL_SET_ERR_MSG_MOD(extack, "Failed to change VLAN Ethertype");

        /* Switch port identification based on 802.1Q is only passable
         * if we are not under a vlan_filtering bridge. So make sure
         * the two configurations are mutually exclusive (of course, the
         * user may know better, i.e. best_effort_vlan_filtering).
         */
        return sja1105_setup_8021q_tagging(ds, want_tagging);
}

/* Returns number of VLANs added (0 or 1) on success,
 * or a negative error code.
 */
static int sja1105_vlan_add_one(struct dsa_switch *ds, int port, u16 vid,
                                u16 flags, struct list_head *vlan_list)
{
        bool untagged = flags & BRIDGE_VLAN_INFO_UNTAGGED;
        bool pvid = flags & BRIDGE_VLAN_INFO_PVID;
        struct sja1105_bridge_vlan *v;

        list_for_each_entry(v, vlan_list, list) {
                if (v->port == port && v->vid == vid) {
                        /* Already added */
                        if (v->untagged == untagged && v->pvid == pvid)
                                /* Nothing changed */
                                return 0;

                        /* It's the same VLAN, but some of the flags changed
                         * and the user did not bother to delete it first.
                         * Update it and trigger sja1105_build_vlan_table.
                         */
                        v->untagged = untagged;
                        v->pvid = pvid;
                        return 1;
                }
        }

        v = kzalloc(sizeof(*v), GFP_KERNEL);
        if (!v) {
                dev_err(ds->dev, "Out of memory while storing VLAN\n");
                return -ENOMEM;
        }

        v->port = port;
        v->vid = vid;
        v->untagged = untagged;
        v->pvid = pvid;
        list_add(&v->list, vlan_list);

        return 1;
}

/* Returns number of VLANs deleted (0 or 1) */
static int sja1105_vlan_del_one(struct dsa_switch *ds, int port, u16 vid,
                                struct list_head *vlan_list)
{
        struct sja1105_bridge_vlan *v, *n;

        list_for_each_entry_safe(v, n, vlan_list, list) {
                if (v->port == port && v->vid == vid) {
                        list_del(&v->list);
                        kfree(v);
                        return 1;
                }
        }

        return 0;
}

static int sja1105_vlan_add(struct dsa_switch *ds, int port,
                            const struct switchdev_obj_port_vlan *vlan,
                            struct netlink_ext_ack *extack)
{
        struct sja1105_private *priv = ds->priv;
        bool vlan_table_changed = false;
        int rc;

        /* If the user wants best-effort VLAN filtering (aka vlan_filtering
         * bridge plus tagging), be sure to at least deny alterations to the
         * configuration done by dsa_8021q.
         */
        if (priv->vlan_state != SJA1105_VLAN_FILTERING_FULL &&
            vid_is_dsa_8021q(vlan->vid)) {
                NL_SET_ERR_MSG_MOD(extack,
                                   "Range 1024-3071 reserved for dsa_8021q operation");
                return -EBUSY;
        }

        rc = sja1105_vlan_add_one(ds, port, vlan->vid, vlan->flags,
                                  &priv->bridge_vlans);
        if (rc < 0)
                return rc;
        if (rc > 0)
                vlan_table_changed = true;

        if (!vlan_table_changed)
                return 0;

        return sja1105_build_vlan_table(priv, true);
}

static int sja1105_vlan_del(struct dsa_switch *ds, int port,
                            const struct switchdev_obj_port_vlan *vlan)
{
        struct sja1105_private *priv = ds->priv;
        bool vlan_table_changed = false;
        int rc;

        rc = sja1105_vlan_del_one(ds, port, vlan->vid, &priv->bridge_vlans);
        if (rc > 0)
                vlan_table_changed = true;

        if (!vlan_table_changed)
                return 0;

        return sja1105_build_vlan_table(priv, true);
}

static int sja1105_dsa_8021q_vlan_add(struct dsa_switch *ds, int port, u16 vid,
                                      u16 flags)
{
        struct sja1105_private *priv = ds->priv;
        int rc;

        rc = sja1105_vlan_add_one(ds, port, vid, flags, &priv->dsa_8021q_vlans);
        if (rc <= 0)
                return rc;

        return sja1105_build_vlan_table(priv, true);
}

static int sja1105_dsa_8021q_vlan_del(struct dsa_switch *ds, int port, u16 vid)
{
        struct sja1105_private *priv = ds->priv;
        int rc;

        rc = sja1105_vlan_del_one(ds, port, vid, &priv->dsa_8021q_vlans);
        if (!rc)
                return 0;

        return sja1105_build_vlan_table(priv, true);
}

static const struct dsa_8021q_ops sja1105_dsa_8021q_ops = {
        .vlan_add       = sja1105_dsa_8021q_vlan_add,
        .vlan_del       = sja1105_dsa_8021q_vlan_del,
};

/* The programming model for the SJA1105 switch is "all-at-once" via static
 * configuration tables. Some of these can be dynamically modified at runtime,
 * but not the xMII mode parameters table.
 * Furthermode, some PHYs may not have crystals for generating their clocks
 * (e.g. RMII). Instead, their 50MHz clock is supplied via the SJA1105 port's
 * ref_clk pin. So port clocking needs to be initialized early, before
 * connecting to PHYs is attempted, otherwise they won't respond through MDIO.
 * Setting correct PHY link speed does not matter now.
 * But dsa_slave_phy_setup is called later than sja1105_setup, so the PHY
 * bindings are not yet parsed by DSA core. We need to parse early so that we
 * can populate the xMII mode parameters table.
 */
static int sja1105_setup(struct dsa_switch *ds)
{
        struct sja1105_private *priv = ds->priv;
        int rc;

        rc = sja1105_parse_dt(priv);
        if (rc < 0) {
                dev_err(ds->dev, "Failed to parse DT: %d\n", rc);
                return rc;
        }

        /* Error out early if internal delays are required through DT
         * and we can't apply them.
         */
        rc = sja1105_parse_rgmii_delays(priv);
        if (rc < 0) {
                dev_err(ds->dev, "RGMII delay not supported\n");
                return rc;
        }

        rc = sja1105_ptp_clock_register(ds);
        if (rc < 0) {
                dev_err(ds->dev, "Failed to register PTP clock: %d\n", rc);
                return rc;
        }

        rc = sja1105_mdiobus_register(ds);
        if (rc < 0) {
                dev_err(ds->dev, "Failed to register MDIO bus: %pe\n",
                        ERR_PTR(rc));
                goto out_ptp_clock_unregister;
        }

        if (priv->info->disable_microcontroller) {
                rc = priv->info->disable_microcontroller(priv);
                if (rc < 0) {
                        dev_err(ds->dev,
                                "Failed to disable microcontroller: %pe\n",
                                ERR_PTR(rc));
                        goto out_mdiobus_unregister;
                }
        }

        /* Create and send configuration down to device */
        rc = sja1105_static_config_load(priv);
        if (rc < 0) {
                dev_err(ds->dev, "Failed to load static config: %d\n", rc);
                goto out_mdiobus_unregister;
        }

        /* Configure the CGU (PHY link modes and speeds) */
        if (priv->info->clocking_setup) {
                rc = priv->info->clocking_setup(priv);
                if (rc < 0) {
                        dev_err(ds->dev,
                                "Failed to configure MII clocking: %pe\n",
                                ERR_PTR(rc));
                        goto out_static_config_free;
                }
        }

        /* On SJA1105, VLAN filtering per se is always enabled in hardware.
         * The only thing we can do to disable it is lie about what the 802.1Q
         * EtherType is.
         * So it will still try to apply VLAN filtering, but all ingress
         * traffic (except frames received with EtherType of ETH_P_SJA1105)
         * will be internally tagged with a distorted VLAN header where the
         * TPID is ETH_P_SJA1105, and the VLAN ID is the port pvid.
         */
        ds->vlan_filtering_is_global = true;

        /* Advertise the 8 egress queues */
        ds->num_tx_queues = SJA1105_NUM_TC;

        ds->mtu_enforcement_ingress = true;

        priv->best_effort_vlan_filtering = true;

        rc = sja1105_devlink_setup(ds);
        if (rc < 0)
                goto out_static_config_free;

        /* The DSA/switchdev model brings up switch ports in standalone mode by
         * default, and that means vlan_filtering is 0 since they're not under
         * a bridge, so it's safe to set up switch tagging at this time.
         */
        rtnl_lock();
        rc = sja1105_setup_8021q_tagging(ds, true);
        rtnl_unlock();
        if (rc)
                goto out_devlink_teardown;

        return 0;

out_devlink_teardown:
        sja1105_devlink_teardown(ds);
out_mdiobus_unregister:
        sja1105_mdiobus_unregister(ds);
out_ptp_clock_unregister:
        sja1105_ptp_clock_unregister(ds);
out_static_config_free:
        sja1105_static_config_free(&priv->static_config);

        return rc;
}

static void sja1105_teardown(struct dsa_switch *ds)
{
        struct sja1105_private *priv = ds->priv;
        struct sja1105_bridge_vlan *v, *n;
        int port;

        for (port = 0; port < ds->num_ports; port++) {
                struct sja1105_port *sp = &priv->ports[port];

                if (!dsa_is_user_port(ds, port))
                        continue;

                if (sp->xmit_worker)
                        kthread_destroy_worker(sp->xmit_worker);
        }

        sja1105_devlink_teardown(ds);
        sja1105_flower_teardown(ds);
        sja1105_tas_teardown(ds);
        sja1105_ptp_clock_unregister(ds);
        sja1105_static_config_free(&priv->static_config);

        list_for_each_entry_safe(v, n, &priv->dsa_8021q_vlans, list) {
                list_del(&v->list);
                kfree(v);
        }

        list_for_each_entry_safe(v, n, &priv->bridge_vlans, list) {
                list_del(&v->list);
                kfree(v);
        }
}

static void sja1105_port_disable(struct dsa_switch *ds, int port)
{
        struct sja1105_private *priv = ds->priv;
        struct sja1105_port *sp = &priv->ports[port];

        if (!dsa_is_user_port(ds, port))
                return;

        kthread_cancel_work_sync(&sp->xmit_work);
        skb_queue_purge(&sp->xmit_queue);
}

static int sja1105_mgmt_xmit(struct dsa_switch *ds, int port, int slot,
                             struct sk_buff *skb, bool takets)
{
        struct sja1105_mgmt_entry mgmt_route = {0};
        struct sja1105_private *priv = ds->priv;
        struct ethhdr *hdr;
        int timeout = 10;
        int rc;

        hdr = eth_hdr(skb);

        mgmt_route.macaddr = ether_addr_to_u64(hdr->h_dest);
        mgmt_route.destports = BIT(port);
        mgmt_route.enfport = 1;
        mgmt_route.tsreg = 0;
        mgmt_route.takets = takets;

        rc = sja1105_dynamic_config_write(priv, BLK_IDX_MGMT_ROUTE,
                                          slot, &mgmt_route, true);
        if (rc < 0) {
                kfree_skb(skb);
                return rc;
        }

        /* Transfer skb to the host port. */
        dsa_enqueue_skb(skb, dsa_to_port(ds, port)->slave);

        /* Wait until the switch has processed the frame */
        do {
                rc = sja1105_dynamic_config_read(priv, BLK_IDX_MGMT_ROUTE,
                                                 slot, &mgmt_route);
                if (rc < 0) {
                        dev_err_ratelimited(priv->ds->dev,
                                            "failed to poll for mgmt route\n");
                        continue;
                }

                /* UM10944: The ENFPORT flag of the respective entry is
                 * cleared when a match is found. The host can use this
                 * flag as an acknowledgment.
                 */
                cpu_relax();
        } while (mgmt_route.enfport && --timeout);

        if (!timeout) {
                /* Clean up the management route so that a follow-up
                 * frame may not match on it by mistake.
                 * This is only hardware supported on P/Q/R/S - on E/T it is
                 * a no-op and we are silently discarding the -EOPNOTSUPP.
                 */
                sja1105_dynamic_config_write(priv, BLK_IDX_MGMT_ROUTE,
                                             slot, &mgmt_route, false);
                dev_err_ratelimited(priv->ds->dev, "xmit timed out\n");
        }

        return NETDEV_TX_OK;
}

#define work_to_port(work) \
                container_of((work), struct sja1105_port, xmit_work)
#define tagger_to_sja1105(t) \
                container_of((t), struct sja1105_private, tagger_data)

/* Deferred work is unfortunately necessary because setting up the management
 * route cannot be done from atomit context (SPI transfer takes a sleepable
 * lock on the bus)
 */
static void sja1105_port_deferred_xmit(struct kthread_work *work)
{
        struct sja1105_port *sp = work_to_port(work);
        struct sja1105_tagger_data *tagger_data = sp->data;
        struct sja1105_private *priv = tagger_to_sja1105(tagger_data);
        int port = sp - priv->ports;
        struct sk_buff *skb;

        while ((skb = skb_dequeue(&sp->xmit_queue)) != NULL) {
                struct sk_buff *clone = SJA1105_SKB_CB(skb)->clone;

                mutex_lock(&priv->mgmt_lock);

                sja1105_mgmt_xmit(priv->ds, port, 0, skb, !!clone);

                /* The clone, if there, was made by dsa_skb_tx_timestamp */
                if (clone)
                        sja1105_ptp_txtstamp_skb(priv->ds, port, clone);

                mutex_unlock(&priv->mgmt_lock);
        }
}

/* The MAXAGE setting belongs to the L2 Forwarding Parameters table,
 * which cannot be reconfigured at runtime. So a switch reset is required.
 */
static int sja1105_set_ageing_time(struct dsa_switch *ds,
                                   unsigned int ageing_time)
{
        struct sja1105_l2_lookup_params_entry *l2_lookup_params;
        struct sja1105_private *priv = ds->priv;
        struct sja1105_table *table;
        unsigned int maxage;

        table = &priv->static_config.tables[BLK_IDX_L2_LOOKUP_PARAMS];
        l2_lookup_params = table->entries;

        maxage = SJA1105_AGEING_TIME_MS(ageing_time);

        if (l2_lookup_params->maxage == maxage)
                return 0;

        l2_lookup_params->maxage = maxage;

        return sja1105_static_config_reload(priv, SJA1105_AGEING_TIME);
}

static int sja1105_change_mtu(struct dsa_switch *ds, int port, int new_mtu)
{
        struct sja1105_l2_policing_entry *policing;
        struct sja1105_private *priv = ds->priv;

        new_mtu += VLAN_ETH_HLEN + ETH_FCS_LEN;

        if (dsa_is_cpu_port(ds, port))
                new_mtu += VLAN_HLEN;

        policing = priv->static_config.tables[BLK_IDX_L2_POLICING].entries;

        if (policing[port].maxlen == new_mtu)
                return 0;

        policing[port].maxlen = new_mtu;

        return sja1105_static_config_reload(priv, SJA1105_BEST_EFFORT_POLICING);
}

static int sja1105_get_max_mtu(struct dsa_switch *ds, int port)
{
        return 2043 - VLAN_ETH_HLEN - ETH_FCS_LEN;
}

static int sja1105_port_setup_tc(struct dsa_switch *ds, int port,
                                 enum tc_setup_type type,
                                 void *type_data)
{
        switch (type) {
        case TC_SETUP_QDISC_TAPRIO:
                return sja1105_setup_tc_taprio(ds, port, type_data);
        case TC_SETUP_QDISC_CBS:
                return sja1105_setup_tc_cbs(ds, port, type_data);
        default:
                return -EOPNOTSUPP;
        }
}

/* We have a single mirror (@to) port, but can configure ingress and egress
 * mirroring on all other (@from) ports.
 * We need to allow mirroring rules only as long as the @to port is always the
 * same, and we need to unset the @to port from mirr_port only when there is no
 * mirroring rule that references it.
 */
static int sja1105_mirror_apply(struct sja1105_private *priv, int from, int to,
                                bool ingress, bool enabled)
{
        struct sja1105_general_params_entry *general_params;
        struct sja1105_mac_config_entry *mac;
        struct dsa_switch *ds = priv->ds;
        struct sja1105_table *table;
        bool already_enabled;
        u64 new_mirr_port;
        int rc;

        table = &priv->static_config.tables[BLK_IDX_GENERAL_PARAMS];
        general_params = table->entries;

        mac = priv->static_config.tables[BLK_IDX_MAC_CONFIG].entries;

        already_enabled = (general_params->mirr_port != ds->num_ports);
        if (already_enabled && enabled && general_params->mirr_port != to) {
                dev_err(priv->ds->dev,
                        "Delete mirroring rules towards port %llu first\n",
                        general_params->mirr_port);
                return -EBUSY;
        }

        new_mirr_port = to;
        if (!enabled) {
                bool keep = false;
                int port;

                /* Anybody still referencing mirr_port? */
                for (port = 0; port < ds->num_ports; port++) {
                        if (mac[port].ing_mirr || mac[port].egr_mirr) {
                                keep = true;
                                break;
                        }
                }
                /* Unset already_enabled for next time */
                if (!keep)
                        new_mirr_port = ds->num_ports;
        }
        if (new_mirr_port != general_params->mirr_port) {
                general_params->mirr_port = new_mirr_port;

                rc = sja1105_dynamic_config_write(priv, BLK_IDX_GENERAL_PARAMS,
                                                  0, general_params, true);
                if (rc < 0)
                        return rc;
        }

        if (ingress)
                mac[from].ing_mirr = enabled;
        else
                mac[from].egr_mirr = enabled;

        return sja1105_dynamic_config_write(priv, BLK_IDX_MAC_CONFIG, from,
                                            &mac[from], true);
}

static int sja1105_mirror_add(struct dsa_switch *ds, int port,
                              struct dsa_mall_mirror_tc_entry *mirror,
                              bool ingress)
{
        return sja1105_mirror_apply(ds->priv, port, mirror->to_local_port,
                                    ingress, true);
}

static void sja1105_mirror_del(struct dsa_switch *ds, int port,
                               struct dsa_mall_mirror_tc_entry *mirror)
{
        sja1105_mirror_apply(ds->priv, port, mirror->to_local_port,
                             mirror->ingress, false);
}

static int sja1105_port_policer_add(struct dsa_switch *ds, int port,
                                    struct dsa_mall_policer_tc_entry *policer)
{
        struct sja1105_l2_policing_entry *policing;
        struct sja1105_private *priv = ds->priv;

        policing = priv->static_config.tables[BLK_IDX_L2_POLICING].entries;

        /* In hardware, every 8 microseconds the credit level is incremented by
         * the value of RATE bytes divided by 64, up to a maximum of SMAX
         * bytes.
         */
        policing[port].rate = div_u64(512 * policer->rate_bytes_per_sec,
                                      1000000);
        policing[port].smax = policer->burst;

        return sja1105_static_config_reload(priv, SJA1105_BEST_EFFORT_POLICING);
}

static void sja1105_port_policer_del(struct dsa_switch *ds, int port)
{
        struct sja1105_l2_policing_entry *policing;
        struct sja1105_private *priv = ds->priv;

        policing = priv->static_config.tables[BLK_IDX_L2_POLICING].entries;

        policing[port].rate = SJA1105_RATE_MBPS(1000);
        policing[port].smax = 65535;

        sja1105_static_config_reload(priv, SJA1105_BEST_EFFORT_POLICING);
}

static int sja1105_port_set_learning(struct sja1105_private *priv, int port,
                                     bool enabled)
{
        struct sja1105_mac_config_entry *mac;
        int rc;

        mac = priv->static_config.tables[BLK_IDX_MAC_CONFIG].entries;

        mac[port].dyn_learn = enabled;

        rc = sja1105_dynamic_config_write(priv, BLK_IDX_MAC_CONFIG, port,
                                          &mac[port], true);
        if (rc)
                return rc;

        if (enabled)
                priv->learn_ena |= BIT(port);
        else
                priv->learn_ena &= ~BIT(port);

        return 0;
}

static int sja1105_port_ucast_bcast_flood(struct sja1105_private *priv, int to,
                                          struct switchdev_brport_flags flags)
{
        if (flags.mask & BR_FLOOD) {
                if (flags.val & BR_FLOOD)
                        priv->ucast_egress_floods |= BIT(to);
                else
                        priv->ucast_egress_floods &= ~BIT(to);
        }

        if (flags.mask & BR_BCAST_FLOOD) {
                if (flags.val & BR_BCAST_FLOOD)
                        priv->bcast_egress_floods |= BIT(to);
                else
                        priv->bcast_egress_floods &= ~BIT(to);
        }

        return sja1105_manage_flood_domains(priv);
}

static int sja1105_port_mcast_flood(struct sja1105_private *priv, int to,
                                    struct switchdev_brport_flags flags,
                                    struct netlink_ext_ack *extack)
{
        struct sja1105_l2_lookup_entry *l2_lookup;
        struct sja1105_table *table;
        int match;

        table = &priv->static_config.tables[BLK_IDX_L2_LOOKUP];
        l2_lookup = table->entries;

        for (match = 0; match < table->entry_count; match++)
                if (l2_lookup[match].macaddr == SJA1105_UNKNOWN_MULTICAST &&
                    l2_lookup[match].mask_macaddr == SJA1105_UNKNOWN_MULTICAST)
                        break;

        if (match == table->entry_count) {
                NL_SET_ERR_MSG_MOD(extack,
                                   "Could not find FDB entry for unknown multicast");
                return -ENOSPC;
        }

        if (flags.val & BR_MCAST_FLOOD)
                l2_lookup[match].destports |= BIT(to);
        else
                l2_lookup[match].destports &= ~BIT(to);

        return sja1105_dynamic_config_write(priv, BLK_IDX_L2_LOOKUP,
                                            l2_lookup[match].index,
                                            &l2_lookup[match],
                                            true);
}

static int sja1105_port_pre_bridge_flags(struct dsa_switch *ds, int port,
                                         struct switchdev_brport_flags flags,
                                         struct netlink_ext_ack *extack)
{
        struct sja1105_private *priv = ds->priv;

        if (flags.mask & ~(BR_LEARNING | BR_FLOOD | BR_MCAST_FLOOD |
                           BR_BCAST_FLOOD))
                return -EINVAL;

        if (flags.mask & (BR_FLOOD | BR_MCAST_FLOOD) &&
            !priv->info->can_limit_mcast_flood) {
                bool multicast = !!(flags.val & BR_MCAST_FLOOD);
                bool unicast = !!(flags.val & BR_FLOOD);

                if (unicast != multicast) {
                        NL_SET_ERR_MSG_MOD(extack,
                                           "This chip cannot configure multicast flooding independently of unicast");
                        return -EINVAL;
                }
        }

        return 0;
}

static int sja1105_port_bridge_flags(struct dsa_switch *ds, int port,
                                     struct switchdev_brport_flags flags,
                                     struct netlink_ext_ack *extack)
{
        struct sja1105_private *priv = ds->priv;
        int rc;

        if (flags.mask & BR_LEARNING) {
                bool learn_ena = !!(flags.val & BR_LEARNING);

                rc = sja1105_port_set_learning(priv, port, learn_ena);
                if (rc)
                        return rc;
        }

        if (flags.mask & (BR_FLOOD | BR_BCAST_FLOOD)) {
                rc = sja1105_port_ucast_bcast_flood(priv, port, flags);
                if (rc)
                        return rc;
        }

        /* For chips that can't offload BR_MCAST_FLOOD independently, there
         * is nothing to do here, we ensured the configuration is in sync by
         * offloading BR_FLOOD.
         */
        if (flags.mask & BR_MCAST_FLOOD && priv->info->can_limit_mcast_flood) {
                rc = sja1105_port_mcast_flood(priv, port, flags,
                                              extack);
                if (rc)
                        return rc;
        }

        return 0;
}

static const struct dsa_switch_ops sja1105_switch_ops = {
        .get_tag_protocol       = sja1105_get_tag_protocol,
        .setup                  = sja1105_setup,
        .teardown               = sja1105_teardown,
        .set_ageing_time        = sja1105_set_ageing_time,
        .port_change_mtu        = sja1105_change_mtu,
        .port_max_mtu           = sja1105_get_max_mtu,
        .phylink_validate       = sja1105_phylink_validate,
        .phylink_mac_config     = sja1105_mac_config,
        .phylink_mac_link_up    = sja1105_mac_link_up,
        .phylink_mac_link_down  = sja1105_mac_link_down,
        .get_strings            = sja1105_get_strings,
        .get_ethtool_stats      = sja1105_get_ethtool_stats,
        .get_sset_count         = sja1105_get_sset_count,
        .get_ts_info            = sja1105_get_ts_info,
        .port_disable           = sja1105_port_disable,
        .port_fdb_dump          = sja1105_fdb_dump,
        .port_fdb_add           = sja1105_fdb_add,
        .port_fdb_del           = sja1105_fdb_del,
        .port_bridge_join       = sja1105_bridge_join,
        .port_bridge_leave      = sja1105_bridge_leave,
        .port_pre_bridge_flags  = sja1105_port_pre_bridge_flags,
        .port_bridge_flags      = sja1105_port_bridge_flags,
        .port_stp_state_set     = sja1105_bridge_stp_state_set,
        .port_vlan_filtering    = sja1105_vlan_filtering,
        .port_vlan_add          = sja1105_vlan_add,
        .port_vlan_del          = sja1105_vlan_del,
        .port_mdb_add           = sja1105_mdb_add,
        .port_mdb_del           = sja1105_mdb_del,
        .port_hwtstamp_get      = sja1105_hwtstamp_get,
        .port_hwtstamp_set      = sja1105_hwtstamp_set,
        .port_rxtstamp          = sja1105_port_rxtstamp,
        .port_txtstamp          = sja1105_port_txtstamp,
        .port_setup_tc          = sja1105_port_setup_tc,
        .port_mirror_add        = sja1105_mirror_add,
        .port_mirror_del        = sja1105_mirror_del,
        .port_policer_add       = sja1105_port_policer_add,
        .port_policer_del       = sja1105_port_policer_del,
        .cls_flower_add         = sja1105_cls_flower_add,
        .cls_flower_del         = sja1105_cls_flower_del,
        .cls_flower_stats       = sja1105_cls_flower_stats,
        .crosschip_bridge_join  = sja1105_crosschip_bridge_join,
        .crosschip_bridge_leave = sja1105_crosschip_bridge_leave,
        .devlink_param_get      = sja1105_devlink_param_get,
        .devlink_param_set      = sja1105_devlink_param_set,
        .devlink_info_get       = sja1105_devlink_info_get,
};

static const struct of_device_id sja1105_dt_ids[];

static int sja1105_check_device_id(struct sja1105_private *priv)
{
        const struct sja1105_regs *regs = priv->info->regs;
        u8 prod_id[SJA1105_SIZE_DEVICE_ID] = {0};
        struct device *dev = &priv->spidev->dev;
        const struct of_device_id *match;
        u32 device_id;
        u64 part_no;
        int rc;

        rc = sja1105_xfer_u32(priv, SPI_READ, regs->device_id, &device_id,
                              NULL);
        if (rc < 0)
                return rc;

        rc = sja1105_xfer_buf(priv, SPI_READ, regs->prod_id, prod_id,
                              SJA1105_SIZE_DEVICE_ID);
        if (rc < 0)
                return rc;

        sja1105_unpack(prod_id, &part_no, 19, 4, SJA1105_SIZE_DEVICE_ID);

        for (match = sja1105_dt_ids; match->compatible[0]; match++) {
                const struct sja1105_info *info = match->data;

                /* Is what's been probed in our match table at all? */
                if (info->device_id != device_id || info->part_no != part_no)
                        continue;

                /* But is it what's in the device tree? */
                if (priv->info->device_id != device_id ||
                    priv->info->part_no != part_no) {
                        dev_warn(dev, "Device tree specifies chip %s but found %s, please fix it!\n",
                                 priv->info->name, info->name);
                        /* It isn't. No problem, pick that up. */
                        priv->info = info;
                }

                return 0;
        }

        dev_err(dev, "Unexpected {device ID, part number}: 0x%x 0x%llx\n",
                device_id, part_no);

        return -ENODEV;
}

static int sja1105_probe(struct spi_device *spi)
{
        struct sja1105_tagger_data *tagger_data;
        struct device *dev = &spi->dev;
        struct sja1105_private *priv;
        size_t max_xfer, max_msg;
        struct dsa_switch *ds;
        int rc, port;

        if (!dev->of_node) {
                dev_err(dev, "No DTS bindings for SJA1105 driver\n");
                return -EINVAL;
        }

        priv = devm_kzalloc(dev, sizeof(struct sja1105_private), GFP_KERNEL);
        if (!priv)
                return -ENOMEM;

        /* Configure the optional reset pin and bring up switch */
        priv->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
        if (IS_ERR(priv->reset_gpio))
                dev_dbg(dev, "reset-gpios not defined, ignoring\n");
        else
                sja1105_hw_reset(priv->reset_gpio, 1, 1);

        /* Populate our driver private structure (priv) based on
         * the device tree node that was probed (spi)
         */
        priv->spidev = spi;
        spi_set_drvdata(spi, priv);

        /* Configure the SPI bus */
        spi->bits_per_word = 8;
        rc = spi_setup(spi);
        if (rc < 0) {
                dev_err(dev, "Could not init SPI\n");
                return rc;
        }

        /* In sja1105_xfer, we send spi_messages composed of two spi_transfers:
         * a small one for the message header and another one for the current
         * chunk of the packed buffer.
         * Check that the restrictions imposed by the SPI controller are
         * respected: the chunk buffer is smaller than the max transfer size,
         * and the total length of the chunk plus its message header is smaller
         * than the max message size.
         * We do that during probe time since the maximum transfer size is a
         * runtime invariant.
         */
        max_xfer = spi_max_transfer_size(spi);
        max_msg = spi_max_message_size(spi);

        /* We need to send at least one 64-bit word of SPI payload per message
         * in order to be able to make useful progress.
         */
        if (max_msg < SJA1105_SIZE_SPI_MSG_HEADER + 8) {
                dev_err(dev, "SPI master cannot send large enough buffers, aborting\n");
                return -EINVAL;
        }

        priv->max_xfer_len = SJA1105_SIZE_SPI_MSG_MAXLEN;
        if (priv->max_xfer_len > max_xfer)
                priv->max_xfer_len = max_xfer;
        if (priv->max_xfer_len > max_msg - SJA1105_SIZE_SPI_MSG_HEADER)
                priv->max_xfer_len = max_msg - SJA1105_SIZE_SPI_MSG_HEADER;

        priv->info = of_device_get_match_data(dev);

        /* Detect hardware device */
        rc = sja1105_check_device_id(priv);
        if (rc < 0) {
                dev_err(dev, "Device ID check failed: %d\n", rc);
                return rc;
        }

        dev_info(dev, "Probed switch chip: %s\n", priv->info->name);

        ds = devm_kzalloc(dev, sizeof(*ds), GFP_KERNEL);
        if (!ds)
                return -ENOMEM;

        ds->dev = dev;
        ds->num_ports = priv->info->num_ports;
        ds->ops = &sja1105_switch_ops;
        ds->priv = priv;
        priv->ds = ds;

        tagger_data = &priv->tagger_data;

        mutex_init(&priv->ptp_data.lock);
        mutex_init(&priv->mgmt_lock);

        priv->dsa_8021q_ctx = devm_kzalloc(dev, sizeof(*priv->dsa_8021q_ctx),
                                           GFP_KERNEL);
        if (!priv->dsa_8021q_ctx)
                return -ENOMEM;

        priv->dsa_8021q_ctx->ops = &sja1105_dsa_8021q_ops;
        priv->dsa_8021q_ctx->proto = htons(ETH_P_8021Q);
        priv->dsa_8021q_ctx->ds = ds;

        INIT_LIST_HEAD(&priv->dsa_8021q_ctx->crosschip_links);
        INIT_LIST_HEAD(&priv->bridge_vlans);
        INIT_LIST_HEAD(&priv->dsa_8021q_vlans);

        sja1105_tas_setup(ds);
        sja1105_flower_setup(ds);

        rc = dsa_register_switch(priv->ds);
        if (rc)
                return rc;

        if (IS_ENABLED(CONFIG_NET_SCH_CBS)) {
                priv->cbs = devm_kcalloc(dev, priv->info->num_cbs_shapers,
                                         sizeof(struct sja1105_cbs_entry),
                                         GFP_KERNEL);
                if (!priv->cbs) {
                        rc = -ENOMEM;
                        goto out_unregister_switch;
                }
        }

        /* Connections between dsa_port and sja1105_port */
        for (port = 0; port < ds->num_ports; port++) {
                struct sja1105_port *sp = &priv->ports[port];
                struct dsa_port *dp = dsa_to_port(ds, port);
                struct net_device *slave;
                int subvlan;

                if (!dsa_is_user_port(ds, port))
                        continue;

                dp->priv = sp;
                sp->dp = dp;
                sp->data = tagger_data;
                slave = dp->slave;
                kthread_init_work(&sp->xmit_work, sja1105_port_deferred_xmit);
                sp->xmit_worker = kthread_create_worker(0, "%s_xmit",
                                                        slave->name);
                if (IS_ERR(sp->xmit_worker)) {
                        rc = PTR_ERR(sp->xmit_worker);
                        dev_err(ds->dev,
                                "failed to create deferred xmit thread: %d\n",
                                rc);
                        goto out_destroy_workers;
                }
                skb_queue_head_init(&sp->xmit_queue);
                sp->xmit_tpid = ETH_P_SJA1105;

                for (subvlan = 0; subvlan < DSA_8021Q_N_SUBVLAN; subvlan++)
                        sp->subvlan_map[subvlan] = VLAN_N_VID;
        }

        return 0;

out_destroy_workers:
        while (port-- > 0) {
                struct sja1105_port *sp = &priv->ports[port];

                if (!dsa_is_user_port(ds, port))
                        continue;

                kthread_destroy_worker(sp->xmit_worker);
        }

out_unregister_switch:
        dsa_unregister_switch(ds);

        return rc;
}

static int sja1105_remove(struct spi_device *spi)
{
        struct sja1105_private *priv = spi_get_drvdata(spi);

        dsa_unregister_switch(priv->ds);
        return 0;
}

static const struct of_device_id sja1105_dt_ids[] = {
        { .compatible = "nxp,sja1105e", .data = &sja1105e_info },
        { .compatible = "nxp,sja1105t", .data = &sja1105t_info },
        { .compatible = "nxp,sja1105p", .data = &sja1105p_info },
        { .compatible = "nxp,sja1105q", .data = &sja1105q_info },
        { .compatible = "nxp,sja1105r", .data = &sja1105r_info },
        { .compatible = "nxp,sja1105s", .data = &sja1105s_info },
        { .compatible = "nxp,sja1110a", .data = &sja1110a_info },
        { .compatible = "nxp,sja1110b", .data = &sja1110b_info },
        { .compatible = "nxp,sja1110c", .data = &sja1110c_info },
        { .compatible = "nxp,sja1110d", .data = &sja1110d_info },
        { /* sentinel */ },
};
MODULE_DEVICE_TABLE(of, sja1105_dt_ids);

static struct spi_driver sja1105_driver = {
        .driver = {
                .name  = "sja1105",
                .owner = THIS_MODULE,
                .of_match_table = of_match_ptr(sja1105_dt_ids),
        },
        .probe  = sja1105_probe,
        .remove = sja1105_remove,
};

module_spi_driver(sja1105_driver);

MODULE_AUTHOR("Vladimir Oltean <olteanv@gmail.com>");
MODULE_AUTHOR("Georg Waibel <georg.waibel@sensor-technik.de>");
MODULE_DESCRIPTION("SJA1105 Driver");
MODULE_LICENSE("GPL v2");