drivers/net/ethernet/dec/tulip/Kconfig

   1 #
   2 # Tulip family network device configuration
   3 #
   4
   5 config NET_TULIP
   6         bool "DEC - Tulip devices"
   7         depends on (PCI || EISA || CARDBUS)
   8         ---help---
   9           This selects the "Tulip" family of EISA/PCI network cards.
  10
  11 if NET_TULIP
  12
  13 config DE2104X
  14         tristate "Early DECchip Tulip (dc2104x) PCI support"
  15         depends on PCI
  16         select CRC32
  17         ---help---
  18           This driver is developed for the SMC EtherPower series Ethernet
  19           cards and also works with cards based on the DECchip
  20           21040 (Tulip series) chips.  Some LinkSys PCI cards are
  21           of this type.  (If your card is NOT SMC EtherPower 10/100 PCI
  22           (smc9332dst), you can also try the driver for "Generic DECchip"
  23           cards, below.  However, most people with a network card of this type
  24           will say Y here.) Do read the Ethernet-HOWTO, available from
  25           <http://www.tldp.org/docs.html#howto>.
  26
  27           To compile this driver as a module, choose M here. The module will
  28           be called de2104x.
  29
  30 config DE2104X_DSL
  31         int "Descriptor Skip Length in 32 bit longwords"
  32         depends on DE2104X
  33         range 0 31
  34         default 0
  35         ---help---
  36           Setting this value allows to align ring buffer descriptors into their
  37           own cache lines. Value of 4 corresponds to the typical 32 byte line
  38           (the descriptor is 16 bytes). This is necessary on systems that lack
  39           cache coherence, an example is PowerMac 5500. Otherwise 0 is safe.
  40           Default is 0, and range is 0 to 31.
  41
  42 config TULIP
  43         tristate "DECchip Tulip (dc2114x) PCI support"
  44         depends on PCI
  45         select CRC32
  46         ---help---
  47           This driver is developed for the SMC EtherPower series Ethernet
  48           cards and also works with cards based on the DECchip
  49           21140 (Tulip series) chips.  Some LinkSys PCI cards are
  50           of this type.  (If your card is NOT SMC EtherPower 10/100 PCI
  51           (smc9332dst), you can also try the driver for "Generic DECchip"
  52           cards, above.  However, most people with a network card of this type
  53           will say Y here.) Do read the Ethernet-HOWTO, available from
  54           <http://www.tldp.org/docs.html#howto>.
  55
  56           To compile this driver as a module, choose M here. The module will
  57           be called tulip.
  58
  59 config TULIP_MWI
  60         bool "New bus configuration"
  61         depends on TULIP
  62         ---help---
  63           This configures your Tulip card specifically for the card and
  64           system cache line size type you are using.
  65
  66           This is experimental code, not yet tested on many boards.
  67
  68           If unsure, say N.
  69
  70 config TULIP_MMIO
  71         bool "Use PCI shared mem for NIC registers"
  72         depends on TULIP
  73         ---help---
  74           Use PCI shared memory for the NIC registers, rather than going through
  75           the Tulip's PIO (programmed I/O ports).  Faster, but could produce
  76           obscure bugs if your mainboard has memory controller timing issues.
  77           If in doubt, say N.
  78
  79 config TULIP_NAPI
  80         bool "Use RX polling (NAPI)"
  81         depends on TULIP
  82         ---help---
  83           NAPI is a new driver API designed to reduce CPU and interrupt load
  84           when the driver is receiving lots of packets from the card. It is
  85           still somewhat experimental and thus not yet enabled by default.
  86
  87           If your estimated Rx load is 10kpps or more, or if the card will be
  88           deployed on potentially unfriendly networks (e.g. in a firewall),
  89           then say Y here.
  90
  91           If in doubt, say N.
  92
  93 config TULIP_NAPI_HW_MITIGATION
  94         bool "Use Interrupt Mitigation"
  95         depends on TULIP_NAPI
  96         ---help---
  97           Use HW to reduce RX interrupts. Not strictly necessary since NAPI
  98           reduces RX interrupts by itself. Interrupt mitigation reduces RX
  99           interrupts even at low levels of traffic at the cost of a small
 100           latency.
 101
 102           If in doubt, say Y.
 103
 104 config TULIP_DM910X
 105         def_bool y
 106         depends on TULIP && SPARC
 107
 108 config DE4X5
 109         tristate "Generic DECchip & DIGITAL EtherWORKS PCI/EISA"
 110         depends on (PCI || EISA)
 111         select CRC32
 112         ---help---
 113           This is support for the DIGITAL series of PCI/EISA Ethernet cards.
 114           These include the DE425, DE434, DE435, DE450 and DE500 models.  If
 115           you have a network card of this type, say Y and read the
 116           Ethernet-HOWTO, available from
 117           <http://www.tldp.org/docs.html#howto>. More specific
 118           information is contained in
 119           <file:Documentation/networking/de4x5.txt>.
 120
 121           To compile this driver as a module, choose M here. The module will
 122           be called de4x5.
 123
 124 config WINBOND_840
 125         tristate "Winbond W89c840 Ethernet support"
 126         depends on PCI
 127         select CRC32
 128         select NET_CORE
 129         select MII
 130         ---help---
 131           This driver is for the Winbond W89c840 chip.  It also works with
 132           the TX9882 chip on the Compex RL100-ATX board.
 133           More specific information and updates are available from
 134           <http://www.scyld.com/network/drivers.html>.
 135
 136 config DM9102
 137         tristate "Davicom DM910x/DM980x support"
 138         depends on PCI
 139         select CRC32
 140         ---help---
 141           This driver is for DM9102(A)/DM9132/DM9801 compatible PCI cards from
 142           Davicom (<http://www.davicom.com.tw/>).  If you have such a network
 143           (Ethernet) card, say Y.  Some information is contained in the file
 144           <file:Documentation/networking/dmfe.txt>.
 145
 146           To compile this driver as a module, choose M here. The module will
 147           be called dmfe.
 148
 149 config ULI526X
 150         tristate "ULi M526x controller support"
 151         depends on PCI
 152         select CRC32
 153         ---help---
 154           This driver is for ULi M5261/M5263 10/100M Ethernet Controller
 155           (<http://www.nvidia.com/page/uli_drivers.html>).
 156
 157           To compile this driver as a module, choose M here. The module will
 158           be called uli526x.
 159
 160 config PCMCIA_XIRCOM
 161         tristate "Xircom CardBus support"
 162         depends on CARDBUS
 163         ---help---
 164           This driver is for the Digital "Tulip" Ethernet CardBus adapters.
 165           It should work with most DEC 21*4*-based chips/ethercards, as well
 166           as with work-alike chips from Lite-On (PNIC) and Macronix (MXIC) and
 167           ASIX.
 168
 169           To compile this driver as a module, choose M here. The module will
 170           be called xircom_cb.  If unsure, say N.
 171
 172 endif # NET_TULIP