drivers/net/ethernet/freescale/Kconfig

   1 #
   2 # Freescale device configuration
   3 #
   4
   5 config NET_VENDOR_FREESCALE
   6         bool "Freescale devices"
   7         depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \
   8                    M523x || M527x || M5272 || M528x || M520x || M532x || \
   9                    IMX_HAVE_PLATFORM_FEC || MXS_HAVE_PLATFORM_FEC || \
  10                    (PPC_MPC52xx && PPC_BESTCOMM)
  11         ---help---
  12           If you have a network (Ethernet) card belonging to this class, say Y
  13           and read the Ethernet-HOWTO, available from
  14           <http://www.tldp.org/docs.html#howto>.
  15
  16           Note that the answer to this question doesn't directly affect the
  17           kernel: saying N will just cause the configurator to skip all
  18           the questions about IBM devices. If you say Y, you will be asked for
  19           your specific card in the following questions.
  20
  21 if NET_VENDOR_FREESCALE
  22
  23 config FEC
  24         bool "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
  25         depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \
  26                     IMX_HAVE_PLATFORM_FEC || MXS_HAVE_PLATFORM_FEC)
  27         default IMX_HAVE_PLATFORM_FEC || MXS_HAVE_PLATFORM_FEC if ARM
  28         select PHYLIB
  29         ---help---
  30           Say Y here if you want to use the built-in 10/100 Fast ethernet
  31           controller on some Motorola ColdFire and Freescale i.MX processors.
  32
  33 config FEC_MPC52xx
  34         tristate "FEC MPC52xx driver"
  35         depends on PPC_MPC52xx && PPC_BESTCOMM
  36         select CRC32
  37         select PHYLIB
  38         select PPC_BESTCOMM_FEC
  39         ---help---
  40           This option enables support for the MPC5200's on-chip
  41           Fast Ethernet Controller
  42           If compiled as module, it will be called fec_mpc52xx.
  43
  44 config FEC_MPC52xx_MDIO
  45         bool "FEC MPC52xx MDIO bus driver"
  46         depends on FEC_MPC52xx
  47         default y
  48         ---help---
  49           The MPC5200's FEC can connect to the Ethernet either with
  50           an external MII PHY chip or 10 Mbps 7-wire interface
  51           (Motorola? industry standard).
  52           If your board uses an external PHY connected to FEC, enable this.
  53           If not sure, enable.
  54           If compiled as module, it will be called fec_mpc52xx_phy.
  55
  56 source "drivers/net/ethernet/freescale/fs_enet/Kconfig"
  57
  58 config FSL_PQ_MDIO
  59         tristate "Freescale PQ MDIO"
  60         depends on FSL_SOC
  61         select PHYLIB
  62         ---help---
  63           This driver supports the MDIO bus used by the gianfar and UCC drivers.
  64
  65 config UCC_GETH
  66         tristate "Freescale QE Gigabit Ethernet"
  67         depends on QUICC_ENGINE
  68         select FSL_PQ_MDIO
  69         select PHYLIB
  70         ---help---
  71           This driver supports the Gigabit Ethernet mode of the QUICC Engine,
  72           which is available on some Freescale SOCs.
  73
  74 config UGETH_TX_ON_DEMAND
  75         bool "Transmit on Demand support"
  76         depends on UCC_GETH
  77
  78 config GIANFAR
  79         tristate "Gianfar Ethernet"
  80         depends on FSL_SOC
  81         select FSL_PQ_MDIO
  82         select PHYLIB
  83         select CRC32
  84         ---help---
  85           This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
  86           and MPC86xx family of chips, and the FEC on the 8540.
  87
  88 endif # NET_VENDOR_FREESCALE