drivers/net/ethernet/hisilicon/Kconfig

   1 # SPDX-License-Identifier: GPL-2.0-only
   2 #
   3 # HISILICON device configuration
   4 #
   5
   6 config NET_VENDOR_HISILICON
   7         bool "Hisilicon devices"
   8         default y
   9         depends on OF || ACPI
  10         depends on ARM || ARM64 || COMPILE_TEST
  11         ---help---
  12           If you have a network (Ethernet) card belonging to this class, say Y.
  13
  14           Note that the answer to this question doesn't directly affect the
  15           kernel: saying N will just cause the configurator to skip all
  16           the questions about Hisilicon devices. If you say Y, you will be asked
  17           for your specific card in the following questions.
  18
  19 if NET_VENDOR_HISILICON
  20
  21 config HIX5HD2_GMAC
  22         tristate "Hisilicon HIX5HD2 Family Network Device Support"
  23         select PHYLIB
  24         help
  25           This selects the hix5hd2 mac family network device.
  26
  27 config HISI_FEMAC
  28         tristate "Hisilicon Fast Ethernet MAC device support"
  29         depends on HAS_IOMEM
  30         select PHYLIB
  31         select RESET_CONTROLLER
  32         help
  33           This selects the Hisilicon Fast Ethernet MAC device(FEMAC).
  34           The FEMAC receives and transmits data over Ethernet
  35           ports at 10/100 Mbps in full-duplex or half-duplex mode.
  36           The FEMAC exchanges data with the CPU, and supports
  37           the energy efficient Ethernet (EEE).
  38
  39 config HIP04_ETH
  40         tristate "HISILICON P04 Ethernet support"
  41         depends on HAS_IOMEM    # For MFD_SYSCON
  42         select MARVELL_PHY
  43         select MFD_SYSCON
  44         select HNS_MDIO
  45         ---help---
  46           If you wish to compile a kernel for a hardware with hisilicon p04 SoC and
  47           want to use the internal ethernet then you should answer Y to this.
  48
  49 config HNS_MDIO
  50         tristate
  51         select PHYLIB
  52         ---help---
  53           This selects the HNS MDIO support. It is needed by HNS_DSAF to access
  54           the PHY
  55
  56 config HNS
  57         tristate "Hisilicon Network Subsystem Support (Framework)"
  58         ---help---
  59           This selects the framework support for Hisilicon Network Subsystem. It
  60           is needed by any driver which provides HNS acceleration engine or make
  61           use of the engine
  62
  63 config HNS_DSAF
  64         tristate "Hisilicon HNS DSAF device Support"
  65         select HNS
  66         select HNS_MDIO
  67         ---help---
  68           This selects the DSAF (Distributed System Area Frabric) network
  69           acceleration engine support. The engine is used in Hisilicon hip05,
  70           Hi1610 and further ICT SoC
  71
  72 config HNS_ENET
  73         tristate "Hisilicon HNS Ethernet Device Support"
  74         select PHYLIB
  75         select HNS
  76         ---help---
  77           This selects the general ethernet driver for HNS.  This module make
  78           use of any HNS AE driver, such as HNS_DSAF
  79
  80 config HNS3
  81         tristate "Hisilicon Network Subsystem Support HNS3 (Framework)"
  82         depends on PCI
  83         ---help---
  84           This selects the framework support for Hisilicon Network Subsystem 3.
  85           This layer facilitates clients like ENET, RoCE and user-space ethernet
  86           drivers(like ODP)to register with HNAE devices and their associated
  87           operations.
  88
  89 if HNS3
  90
  91 config HNS3_HCLGE
  92         tristate "Hisilicon HNS3 HCLGE Acceleration Engine & Compatibility Layer Support"
  93         default m
  94         depends on PCI_MSI
  95         ---help---
  96           This selects the HNS3_HCLGE network acceleration engine & its hardware
  97           compatibility layer. The engine would be used in Hisilicon hip08 family of
  98           SoCs and further upcoming SoCs.
  99
 100 config HNS3_DCB
 101         bool "Hisilicon HNS3 Data Center Bridge Support"
 102         default n
 103         depends on HNS3_HCLGE && DCB
 104         ---help---
 105           Say Y here if you want to use Data Center Bridging (DCB) in the HNS3 driver.
 106
 107           If unsure, say N.
 108
 109 config HNS3_HCLGEVF
 110         tristate "Hisilicon HNS3VF Acceleration Engine & Compatibility Layer Support"
 111         depends on PCI_MSI
 112         depends on HNS3_HCLGE
 113     ---help---
 114           This selects the HNS3 VF drivers network acceleration engine & its hardware
 115           compatibility layer. The engine would be used in Hisilicon hip08 family of
 116           SoCs and further upcoming SoCs.
 117
 118 config HNS3_ENET
 119         tristate "Hisilicon HNS3 Ethernet Device Support"
 120         default m
 121         depends on 64BIT && PCI
 122         depends on INET
 123         ---help---
 124           This selects the Ethernet Driver for Hisilicon Network Subsystem 3 for hip08
 125           family of SoCs. This module depends upon HNAE3 driver to access the HNAE3
 126           devices and their associated operations.
 127
 128 endif #HNS3
 129
 130 endif # NET_VENDOR_HISILICON