]>
git.proxmox.com Git - mirror_ubuntu-eoan-kernel.git/blob - drivers/net/ethernet/intel/e1000e/defines.h
1 /* Intel PRO/1000 Linux driver
2 * Copyright(c) 1999 - 2015 Intel Corporation.
4 * This program is free software; you can redistribute it and/or modify it
5 * under the terms and conditions of the GNU General Public License,
6 * version 2, as published by the Free Software Foundation.
8 * This program is distributed in the hope it will be useful, but WITHOUT
9 * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
10 * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
13 * The full GNU General Public License is included in this distribution in
14 * the file called "COPYING".
16 * Contact Information:
17 * Linux NICS <linux.nics@intel.com>
18 * e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
19 * Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
22 #ifndef _E1000_DEFINES_H_
23 #define _E1000_DEFINES_H_
25 /* Number of Transmit and Receive Descriptors must be a multiple of 8 */
26 #define REQ_TX_DESCRIPTOR_MULTIPLE 8
27 #define REQ_RX_DESCRIPTOR_MULTIPLE 8
29 /* Definitions for power management and wakeup registers */
31 #define E1000_WUC_APME 0x00000001 /* APM Enable */
32 #define E1000_WUC_PME_EN 0x00000002 /* PME Enable */
33 #define E1000_WUC_PME_STATUS 0x00000004 /* PME Status */
34 #define E1000_WUC_APMPME 0x00000008 /* Assert PME on APM Wakeup */
35 #define E1000_WUC_PHY_WAKE 0x00000100 /* if PHY supports wakeup */
37 /* Wake Up Filter Control */
38 #define E1000_WUFC_LNKC 0x00000001 /* Link Status Change Wakeup Enable */
39 #define E1000_WUFC_MAG 0x00000002 /* Magic Packet Wakeup Enable */
40 #define E1000_WUFC_EX 0x00000004 /* Directed Exact Wakeup Enable */
41 #define E1000_WUFC_MC 0x00000008 /* Directed Multicast Wakeup Enable */
42 #define E1000_WUFC_BC 0x00000010 /* Broadcast Wakeup Enable */
43 #define E1000_WUFC_ARP 0x00000020 /* ARP Request Packet Wakeup Enable */
46 #define E1000_WUS_LNKC E1000_WUFC_LNKC
47 #define E1000_WUS_MAG E1000_WUFC_MAG
48 #define E1000_WUS_EX E1000_WUFC_EX
49 #define E1000_WUS_MC E1000_WUFC_MC
50 #define E1000_WUS_BC E1000_WUFC_BC
52 /* Extended Device Control */
53 #define E1000_CTRL_EXT_LPCD 0x00000004 /* LCD Power Cycle Done */
54 #define E1000_CTRL_EXT_SDP3_DATA 0x00000080 /* Value of SW Definable Pin 3 */
55 #define E1000_CTRL_EXT_FORCE_SMBUS 0x00000800 /* Force SMBus mode */
56 #define E1000_CTRL_EXT_EE_RST 0x00002000 /* Reinitialize from EEPROM */
57 #define E1000_CTRL_EXT_SPD_BYPS 0x00008000 /* Speed Select Bypass */
58 #define E1000_CTRL_EXT_RO_DIS 0x00020000 /* Relaxed Ordering disable */
59 #define E1000_CTRL_EXT_DMA_DYN_CLK_EN 0x00080000 /* DMA Dynamic Clock Gating */
60 #define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000
61 #define E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES 0x00C00000
62 #define E1000_CTRL_EXT_EIAME 0x01000000
63 #define E1000_CTRL_EXT_DRV_LOAD 0x10000000 /* Driver loaded bit for FW */
64 #define E1000_CTRL_EXT_IAME 0x08000000 /* Int ACK Auto-mask */
65 #define E1000_CTRL_EXT_PBA_CLR 0x80000000 /* PBA Clear */
66 #define E1000_CTRL_EXT_LSECCK 0x00001000
67 #define E1000_CTRL_EXT_PHYPDEN 0x00100000
69 /* Receive Descriptor bit definitions */
70 #define E1000_RXD_STAT_DD 0x01 /* Descriptor Done */
71 #define E1000_RXD_STAT_EOP 0x02 /* End of Packet */
72 #define E1000_RXD_STAT_IXSM 0x04 /* Ignore checksum */
73 #define E1000_RXD_STAT_VP 0x08 /* IEEE VLAN Packet */
74 #define E1000_RXD_STAT_UDPCS 0x10 /* UDP xsum calculated */
75 #define E1000_RXD_STAT_TCPCS 0x20 /* TCP xsum calculated */
76 #define E1000_RXD_ERR_CE 0x01 /* CRC Error */
77 #define E1000_RXD_ERR_SE 0x02 /* Symbol Error */
78 #define E1000_RXD_ERR_SEQ 0x04 /* Sequence Error */
79 #define E1000_RXD_ERR_CXE 0x10 /* Carrier Extension Error */
80 #define E1000_RXD_ERR_TCPE 0x20 /* TCP/UDP Checksum Error */
81 #define E1000_RXD_ERR_IPE 0x40 /* IP Checksum Error */
82 #define E1000_RXD_ERR_RXE 0x80 /* Rx Data Error */
83 #define E1000_RXD_SPC_VLAN_MASK 0x0FFF /* VLAN ID is in lower 12 bits */
85 #define E1000_RXDEXT_STATERR_TST 0x00000100 /* Time Stamp taken */
86 #define E1000_RXDEXT_STATERR_CE 0x01000000
87 #define E1000_RXDEXT_STATERR_SE 0x02000000
88 #define E1000_RXDEXT_STATERR_SEQ 0x04000000
89 #define E1000_RXDEXT_STATERR_CXE 0x10000000
90 #define E1000_RXDEXT_STATERR_RXE 0x80000000
92 /* mask to determine if packets should be dropped due to frame errors */
93 #define E1000_RXD_ERR_FRAME_ERR_MASK ( \
100 /* Same mask, but for extended and packet split descriptors */
101 #define E1000_RXDEXT_ERR_FRAME_ERR_MASK ( \
102 E1000_RXDEXT_STATERR_CE | \
103 E1000_RXDEXT_STATERR_SE | \
104 E1000_RXDEXT_STATERR_SEQ | \
105 E1000_RXDEXT_STATERR_CXE | \
106 E1000_RXDEXT_STATERR_RXE)
108 #define E1000_MRQC_RSS_FIELD_MASK 0xFFFF0000
109 #define E1000_MRQC_RSS_FIELD_IPV4_TCP 0x00010000
110 #define E1000_MRQC_RSS_FIELD_IPV4 0x00020000
111 #define E1000_MRQC_RSS_FIELD_IPV6_TCP_EX 0x00040000
112 #define E1000_MRQC_RSS_FIELD_IPV6 0x00100000
113 #define E1000_MRQC_RSS_FIELD_IPV6_TCP 0x00200000
115 #define E1000_RXDPS_HDRSTAT_HDRSP 0x00008000
117 /* Management Control */
118 #define E1000_MANC_SMBUS_EN 0x00000001 /* SMBus Enabled - RO */
119 #define E1000_MANC_ASF_EN 0x00000002 /* ASF Enabled - RO */
120 #define E1000_MANC_ARP_EN 0x00002000 /* Enable ARP Request Filtering */
121 #define E1000_MANC_RCV_TCO_EN 0x00020000 /* Receive TCO Packets Enabled */
122 #define E1000_MANC_BLK_PHY_RST_ON_IDE 0x00040000 /* Block phy resets */
123 /* Enable MAC address filtering */
124 #define E1000_MANC_EN_MAC_ADDR_FILTER 0x00100000
125 /* Enable MNG packets to host memory */
126 #define E1000_MANC_EN_MNG2HOST 0x00200000
128 #define E1000_MANC2H_PORT_623 0x00000020 /* Port 0x26f */
129 #define E1000_MANC2H_PORT_664 0x00000040 /* Port 0x298 */
130 #define E1000_MDEF_PORT_623 0x00000800 /* Port 0x26f */
131 #define E1000_MDEF_PORT_664 0x00000400 /* Port 0x298 */
133 /* Receive Control */
134 #define E1000_RCTL_EN 0x00000002 /* enable */
135 #define E1000_RCTL_SBP 0x00000004 /* store bad packet */
136 #define E1000_RCTL_UPE 0x00000008 /* unicast promiscuous enable */
137 #define E1000_RCTL_MPE 0x00000010 /* multicast promiscuous enab */
138 #define E1000_RCTL_LPE 0x00000020 /* long packet enable */
139 #define E1000_RCTL_LBM_NO 0x00000000 /* no loopback mode */
140 #define E1000_RCTL_LBM_MAC 0x00000040 /* MAC loopback mode */
141 #define E1000_RCTL_LBM_TCVR 0x000000C0 /* tcvr loopback mode */
142 #define E1000_RCTL_DTYP_PS 0x00000400 /* Packet Split descriptor */
143 #define E1000_RCTL_RDMTS_HALF 0x00000000 /* Rx desc min threshold size */
144 #define E1000_RCTL_RDMTS_HEX 0x00010000
145 #define E1000_RCTL_MO_SHIFT 12 /* multicast offset shift */
146 #define E1000_RCTL_MO_3 0x00003000 /* multicast offset 15:4 */
147 #define E1000_RCTL_BAM 0x00008000 /* broadcast enable */
148 /* these buffer sizes are valid if E1000_RCTL_BSEX is 0 */
149 #define E1000_RCTL_SZ_2048 0x00000000 /* Rx buffer size 2048 */
150 #define E1000_RCTL_SZ_1024 0x00010000 /* Rx buffer size 1024 */
151 #define E1000_RCTL_SZ_512 0x00020000 /* Rx buffer size 512 */
152 #define E1000_RCTL_SZ_256 0x00030000 /* Rx buffer size 256 */
153 /* these buffer sizes are valid if E1000_RCTL_BSEX is 1 */
154 #define E1000_RCTL_SZ_16384 0x00010000 /* Rx buffer size 16384 */
155 #define E1000_RCTL_SZ_8192 0x00020000 /* Rx buffer size 8192 */
156 #define E1000_RCTL_SZ_4096 0x00030000 /* Rx buffer size 4096 */
157 #define E1000_RCTL_VFE 0x00040000 /* vlan filter enable */
158 #define E1000_RCTL_CFIEN 0x00080000 /* canonical form enable */
159 #define E1000_RCTL_CFI 0x00100000 /* canonical form indicator */
160 #define E1000_RCTL_DPF 0x00400000 /* Discard Pause Frames */
161 #define E1000_RCTL_PMCF 0x00800000 /* pass MAC control frames */
162 #define E1000_RCTL_BSEX 0x02000000 /* Buffer size extension */
163 #define E1000_RCTL_SECRC 0x04000000 /* Strip Ethernet CRC */
165 /* Use byte values for the following shift parameters
167 * psrctl |= (((ROUNDUP(value0, 128) >> E1000_PSRCTL_BSIZE0_SHIFT) &
168 * E1000_PSRCTL_BSIZE0_MASK) |
169 * ((ROUNDUP(value1, 1024) >> E1000_PSRCTL_BSIZE1_SHIFT) &
170 * E1000_PSRCTL_BSIZE1_MASK) |
171 * ((ROUNDUP(value2, 1024) << E1000_PSRCTL_BSIZE2_SHIFT) &
172 * E1000_PSRCTL_BSIZE2_MASK) |
173 * ((ROUNDUP(value3, 1024) << E1000_PSRCTL_BSIZE3_SHIFT) |;
174 * E1000_PSRCTL_BSIZE3_MASK))
175 * where value0 = [128..16256], default=256
176 * value1 = [1024..64512], default=4096
177 * value2 = [0..64512], default=4096
178 * value3 = [0..64512], default=0
181 #define E1000_PSRCTL_BSIZE0_MASK 0x0000007F
182 #define E1000_PSRCTL_BSIZE1_MASK 0x00003F00
183 #define E1000_PSRCTL_BSIZE2_MASK 0x003F0000
184 #define E1000_PSRCTL_BSIZE3_MASK 0x3F000000
186 #define E1000_PSRCTL_BSIZE0_SHIFT 7 /* Shift _right_ 7 */
187 #define E1000_PSRCTL_BSIZE1_SHIFT 2 /* Shift _right_ 2 */
188 #define E1000_PSRCTL_BSIZE2_SHIFT 6 /* Shift _left_ 6 */
189 #define E1000_PSRCTL_BSIZE3_SHIFT 14 /* Shift _left_ 14 */
191 /* SWFW_SYNC Definitions */
192 #define E1000_SWFW_EEP_SM 0x1
193 #define E1000_SWFW_PHY0_SM 0x2
194 #define E1000_SWFW_PHY1_SM 0x4
195 #define E1000_SWFW_CSR_SM 0x8
198 #define E1000_CTRL_FD 0x00000001 /* Full duplex.0=half; 1=full */
199 #define E1000_CTRL_GIO_MASTER_DISABLE 0x00000004 /*Blocks new Master requests */
200 #define E1000_CTRL_LRST 0x00000008 /* Link reset. 0=normal,1=reset */
201 #define E1000_CTRL_ASDE 0x00000020 /* Auto-speed detect enable */
202 #define E1000_CTRL_SLU 0x00000040 /* Set link up (Force Link) */
203 #define E1000_CTRL_ILOS 0x00000080 /* Invert Loss-Of Signal */
204 #define E1000_CTRL_SPD_SEL 0x00000300 /* Speed Select Mask */
205 #define E1000_CTRL_SPD_10 0x00000000 /* Force 10Mb */
206 #define E1000_CTRL_SPD_100 0x00000100 /* Force 100Mb */
207 #define E1000_CTRL_SPD_1000 0x00000200 /* Force 1Gb */
208 #define E1000_CTRL_FRCSPD 0x00000800 /* Force Speed */
209 #define E1000_CTRL_FRCDPX 0x00001000 /* Force Duplex */
210 #define E1000_CTRL_LANPHYPC_OVERRIDE 0x00010000 /* SW control of LANPHYPC */
211 #define E1000_CTRL_LANPHYPC_VALUE 0x00020000 /* SW value of LANPHYPC */
212 #define E1000_CTRL_MEHE 0x00080000 /* Memory Error Handling Enable */
213 #define E1000_CTRL_SWDPIN0 0x00040000 /* SWDPIN 0 value */
214 #define E1000_CTRL_SWDPIN1 0x00080000 /* SWDPIN 1 value */
215 #define E1000_CTRL_ADVD3WUC 0x00100000 /* D3 WUC */
216 #define E1000_CTRL_EN_PHY_PWR_MGMT 0x00200000 /* PHY PM enable */
217 #define E1000_CTRL_SWDPIO0 0x00400000 /* SWDPIN 0 Input or output */
218 #define E1000_CTRL_RST 0x04000000 /* Global reset */
219 #define E1000_CTRL_RFCE 0x08000000 /* Receive Flow Control enable */
220 #define E1000_CTRL_TFCE 0x10000000 /* Transmit flow control enable */
221 #define E1000_CTRL_VME 0x40000000 /* IEEE VLAN mode enable */
222 #define E1000_CTRL_PHY_RST 0x80000000 /* PHY Reset */
224 #define E1000_PCS_LCTL_FORCE_FCTRL 0x80
226 #define E1000_PCS_LSTS_AN_COMPLETE 0x10000
229 #define E1000_STATUS_FD 0x00000001 /* Full duplex.0=half,1=full */
230 #define E1000_STATUS_LU 0x00000002 /* Link up.0=no,1=link */
231 #define E1000_STATUS_FUNC_MASK 0x0000000C /* PCI Function Mask */
232 #define E1000_STATUS_FUNC_SHIFT 2
233 #define E1000_STATUS_FUNC_1 0x00000004 /* Function 1 */
234 #define E1000_STATUS_TXOFF 0x00000010 /* transmission paused */
235 #define E1000_STATUS_SPEED_MASK 0x000000C0
236 #define E1000_STATUS_SPEED_10 0x00000000 /* Speed 10Mb/s */
237 #define E1000_STATUS_SPEED_100 0x00000040 /* Speed 100Mb/s */
238 #define E1000_STATUS_SPEED_1000 0x00000080 /* Speed 1000Mb/s */
239 #define E1000_STATUS_LAN_INIT_DONE 0x00000200 /* Lan Init Completion by NVM */
240 #define E1000_STATUS_PHYRA 0x00000400 /* PHY Reset Asserted */
241 #define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000 /* Master Req status */
243 #define HALF_DUPLEX 1
244 #define FULL_DUPLEX 2
246 #define ADVERTISE_10_HALF 0x0001
247 #define ADVERTISE_10_FULL 0x0002
248 #define ADVERTISE_100_HALF 0x0004
249 #define ADVERTISE_100_FULL 0x0008
250 #define ADVERTISE_1000_HALF 0x0010 /* Not used, just FYI */
251 #define ADVERTISE_1000_FULL 0x0020
253 /* 1000/H is not supported, nor spec-compliant. */
254 #define E1000_ALL_SPEED_DUPLEX ( \
255 ADVERTISE_10_HALF | ADVERTISE_10_FULL | ADVERTISE_100_HALF | \
256 ADVERTISE_100_FULL | ADVERTISE_1000_FULL)
257 #define E1000_ALL_NOT_GIG ( \
258 ADVERTISE_10_HALF | ADVERTISE_10_FULL | ADVERTISE_100_HALF | \
260 #define E1000_ALL_100_SPEED (ADVERTISE_100_HALF | ADVERTISE_100_FULL)
261 #define E1000_ALL_10_SPEED (ADVERTISE_10_HALF | ADVERTISE_10_FULL)
262 #define E1000_ALL_HALF_DUPLEX (ADVERTISE_10_HALF | ADVERTISE_100_HALF)
264 #define AUTONEG_ADVERTISE_SPEED_DEFAULT E1000_ALL_SPEED_DUPLEX
267 #define E1000_PHY_LED0_MODE_MASK 0x00000007
268 #define E1000_PHY_LED0_IVRT 0x00000008
269 #define E1000_PHY_LED0_MASK 0x0000001F
271 #define E1000_LEDCTL_LED0_MODE_MASK 0x0000000F
272 #define E1000_LEDCTL_LED0_MODE_SHIFT 0
273 #define E1000_LEDCTL_LED0_IVRT 0x00000040
274 #define E1000_LEDCTL_LED0_BLINK 0x00000080
276 #define E1000_LEDCTL_MODE_LINK_UP 0x2
277 #define E1000_LEDCTL_MODE_LED_ON 0xE
278 #define E1000_LEDCTL_MODE_LED_OFF 0xF
280 /* Transmit Descriptor bit definitions */
281 #define E1000_TXD_DTYP_D 0x00100000 /* Data Descriptor */
282 #define E1000_TXD_POPTS_IXSM 0x01 /* Insert IP checksum */
283 #define E1000_TXD_POPTS_TXSM 0x02 /* Insert TCP/UDP checksum */
284 #define E1000_TXD_CMD_EOP 0x01000000 /* End of Packet */
285 #define E1000_TXD_CMD_IFCS 0x02000000 /* Insert FCS (Ethernet CRC) */
286 #define E1000_TXD_CMD_IC 0x04000000 /* Insert Checksum */
287 #define E1000_TXD_CMD_RS 0x08000000 /* Report Status */
288 #define E1000_TXD_CMD_RPS 0x10000000 /* Report Packet Sent */
289 #define E1000_TXD_CMD_DEXT 0x20000000 /* Descriptor extension (0 = legacy) */
290 #define E1000_TXD_CMD_VLE 0x40000000 /* Add VLAN tag */
291 #define E1000_TXD_CMD_IDE 0x80000000 /* Enable Tidv register */
292 #define E1000_TXD_STAT_DD 0x00000001 /* Descriptor Done */
293 #define E1000_TXD_STAT_EC 0x00000002 /* Excess Collisions */
294 #define E1000_TXD_STAT_LC 0x00000004 /* Late Collisions */
295 #define E1000_TXD_STAT_TU 0x00000008 /* Transmit underrun */
296 #define E1000_TXD_CMD_TCP 0x01000000 /* TCP packet */
297 #define E1000_TXD_CMD_IP 0x02000000 /* IP packet */
298 #define E1000_TXD_CMD_TSE 0x04000000 /* TCP Seg enable */
299 #define E1000_TXD_STAT_TC 0x00000004 /* Tx Underrun */
300 #define E1000_TXD_EXTCMD_TSTAMP 0x00000010 /* IEEE1588 Timestamp packet */
302 /* Transmit Control */
303 #define E1000_TCTL_EN 0x00000002 /* enable Tx */
304 #define E1000_TCTL_PSP 0x00000008 /* pad short packets */
305 #define E1000_TCTL_CT 0x00000ff0 /* collision threshold */
306 #define E1000_TCTL_COLD 0x003ff000 /* collision distance */
307 #define E1000_TCTL_RTLC 0x01000000 /* Re-transmit on late collision */
308 #define E1000_TCTL_MULR 0x10000000 /* Multiple request support */
311 #define E1000_SCTL_DISABLE_SERDES_LOOPBACK 0x0400
312 #define E1000_SCTL_ENABLE_SERDES_LOOPBACK 0x0410
314 /* Receive Checksum Control */
315 #define E1000_RXCSUM_TUOFL 0x00000200 /* TCP / UDP checksum offload */
316 #define E1000_RXCSUM_IPPCSE 0x00001000 /* IP payload checksum enable */
317 #define E1000_RXCSUM_PCSD 0x00002000 /* packet checksum disabled */
319 /* Header split receive */
320 #define E1000_RFCTL_NFSW_DIS 0x00000040
321 #define E1000_RFCTL_NFSR_DIS 0x00000080
322 #define E1000_RFCTL_ACK_DIS 0x00001000
323 #define E1000_RFCTL_EXTEN 0x00008000
324 #define E1000_RFCTL_IPV6_EX_DIS 0x00010000
325 #define E1000_RFCTL_NEW_IPV6_EXT_DIS 0x00020000
327 /* Collision related configuration parameters */
328 #define E1000_COLLISION_THRESHOLD 15
329 #define E1000_CT_SHIFT 4
330 #define E1000_COLLISION_DISTANCE 63
331 #define E1000_COLD_SHIFT 12
333 /* Default values for the transmit IPG register */
334 #define DEFAULT_82543_TIPG_IPGT_COPPER 8
336 #define E1000_TIPG_IPGT_MASK 0x000003FF
338 #define DEFAULT_82543_TIPG_IPGR1 8
339 #define E1000_TIPG_IPGR1_SHIFT 10
341 #define DEFAULT_82543_TIPG_IPGR2 6
342 #define DEFAULT_80003ES2LAN_TIPG_IPGR2 7
343 #define E1000_TIPG_IPGR2_SHIFT 20
345 #define MAX_JUMBO_FRAME_SIZE 0x3F00
346 #define E1000_TX_PTR_GAP 0x1F
348 /* Extended Configuration Control and Size */
349 #define E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP 0x00000020
350 #define E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE 0x00000001
351 #define E1000_EXTCNF_CTRL_OEM_WRITE_ENABLE 0x00000008
352 #define E1000_EXTCNF_CTRL_SWFLAG 0x00000020
353 #define E1000_EXTCNF_CTRL_GATE_PHY_CFG 0x00000080
354 #define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK 0x00FF0000
355 #define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT 16
356 #define E1000_EXTCNF_CTRL_EXT_CNF_POINTER_MASK 0x0FFF0000
357 #define E1000_EXTCNF_CTRL_EXT_CNF_POINTER_SHIFT 16
359 #define E1000_PHY_CTRL_D0A_LPLU 0x00000002
360 #define E1000_PHY_CTRL_NOND0A_LPLU 0x00000004
361 #define E1000_PHY_CTRL_NOND0A_GBE_DISABLE 0x00000008
362 #define E1000_PHY_CTRL_GBE_DISABLE 0x00000040
364 #define E1000_KABGTXD_BGSQLBIAS 0x00050000
366 /* Low Power IDLE Control */
367 #define E1000_LPIC_LPIET_SHIFT 24 /* Low Power Idle Entry Time */
370 #define E1000_PBA_8K 0x0008 /* 8KB */
371 #define E1000_PBA_16K 0x0010 /* 16KB */
373 #define E1000_PBA_RXA_MASK 0xFFFF
375 #define E1000_PBS_16K E1000_PBA_16K
377 /* Uncorrectable/correctable ECC Error counts and enable bits */
378 #define E1000_PBECCSTS_CORR_ERR_CNT_MASK 0x000000FF
379 #define E1000_PBECCSTS_UNCORR_ERR_CNT_MASK 0x0000FF00
380 #define E1000_PBECCSTS_UNCORR_ERR_CNT_SHIFT 8
381 #define E1000_PBECCSTS_ECC_ENABLE 0x00010000
387 #define MIN_NUM_XMITS 1000
389 /* SW Semaphore Register */
390 #define E1000_SWSM_SMBI 0x00000001 /* Driver Semaphore bit */
391 #define E1000_SWSM_SWESMBI 0x00000002 /* FW Semaphore bit */
392 #define E1000_SWSM_DRV_LOAD 0x00000008 /* Driver Loaded Bit */
394 #define E1000_SWSM2_LOCK 0x00000002 /* Secondary driver semaphore bit */
396 /* Interrupt Cause Read */
397 #define E1000_ICR_TXDW 0x00000001 /* Transmit desc written back */
398 #define E1000_ICR_LSC 0x00000004 /* Link Status Change */
399 #define E1000_ICR_RXSEQ 0x00000008 /* Rx sequence error */
400 #define E1000_ICR_RXDMT0 0x00000010 /* Rx desc min. threshold (0) */
401 #define E1000_ICR_RXO 0x00000040 /* Receiver Overrun */
402 #define E1000_ICR_RXT0 0x00000080 /* Rx timer intr (ring 0) */
403 #define E1000_ICR_ECCER 0x00400000 /* Uncorrectable ECC Error */
404 /* If this bit asserted, the driver should claim the interrupt */
405 #define E1000_ICR_INT_ASSERTED 0x80000000
406 #define E1000_ICR_RXQ0 0x00100000 /* Rx Queue 0 Interrupt */
407 #define E1000_ICR_RXQ1 0x00200000 /* Rx Queue 1 Interrupt */
408 #define E1000_ICR_TXQ0 0x00400000 /* Tx Queue 0 Interrupt */
409 #define E1000_ICR_TXQ1 0x00800000 /* Tx Queue 1 Interrupt */
410 #define E1000_ICR_OTHER 0x01000000 /* Other Interrupts */
412 /* PBA ECC Register */
413 #define E1000_PBA_ECC_COUNTER_MASK 0xFFF00000 /* ECC counter mask */
414 #define E1000_PBA_ECC_COUNTER_SHIFT 20 /* ECC counter shift value */
415 #define E1000_PBA_ECC_CORR_EN 0x00000001 /* ECC correction enable */
416 #define E1000_PBA_ECC_STAT_CLR 0x00000002 /* Clear ECC error counter */
417 #define E1000_PBA_ECC_INT_EN 0x00000004 /* Enable ICR bit 5 for ECC */
419 /* This defines the bits that are set in the Interrupt Mask
420 * Set/Read Register. Each bit is documented below:
421 * o RXT0 = Receiver Timer Interrupt (ring 0)
422 * o TXDW = Transmit Descriptor Written Back
423 * o RXDMT0 = Receive Descriptor Minimum Threshold hit (ring 0)
424 * o RXSEQ = Receive Sequence Error
425 * o LSC = Link Status Change
427 #define IMS_ENABLE_MASK ( \
434 /* Interrupt Mask Set */
435 #define E1000_IMS_TXDW E1000_ICR_TXDW /* Transmit desc written back */
436 #define E1000_IMS_LSC E1000_ICR_LSC /* Link Status Change */
437 #define E1000_IMS_RXSEQ E1000_ICR_RXSEQ /* Rx sequence error */
438 #define E1000_IMS_RXDMT0 E1000_ICR_RXDMT0 /* Rx desc min. threshold */
439 #define E1000_IMS_RXT0 E1000_ICR_RXT0 /* Rx timer intr */
440 #define E1000_IMS_ECCER E1000_ICR_ECCER /* Uncorrectable ECC Error */
441 #define E1000_IMS_RXQ0 E1000_ICR_RXQ0 /* Rx Queue 0 Interrupt */
442 #define E1000_IMS_RXQ1 E1000_ICR_RXQ1 /* Rx Queue 1 Interrupt */
443 #define E1000_IMS_TXQ0 E1000_ICR_TXQ0 /* Tx Queue 0 Interrupt */
444 #define E1000_IMS_TXQ1 E1000_ICR_TXQ1 /* Tx Queue 1 Interrupt */
445 #define E1000_IMS_OTHER E1000_ICR_OTHER /* Other Interrupt */
447 /* Interrupt Cause Set */
448 #define E1000_ICS_LSC E1000_ICR_LSC /* Link Status Change */
449 #define E1000_ICS_RXSEQ E1000_ICR_RXSEQ /* Rx sequence error */
450 #define E1000_ICS_RXDMT0 E1000_ICR_RXDMT0 /* Rx desc min. threshold */
451 #define E1000_ICS_OTHER E1000_ICR_OTHER /* Other Interrupt */
453 /* Transmit Descriptor Control */
454 #define E1000_TXDCTL_PTHRESH 0x0000003F /* TXDCTL Prefetch Threshold */
455 #define E1000_TXDCTL_HTHRESH 0x00003F00 /* TXDCTL Host Threshold */
456 #define E1000_TXDCTL_WTHRESH 0x003F0000 /* TXDCTL Writeback Threshold */
457 #define E1000_TXDCTL_GRAN 0x01000000 /* TXDCTL Granularity */
458 #define E1000_TXDCTL_FULL_TX_DESC_WB 0x01010000 /* GRAN=1, WTHRESH=1 */
459 #define E1000_TXDCTL_MAX_TX_DESC_PREFETCH 0x0100001F /* GRAN=1, PTHRESH=31 */
460 /* Enable the counting of desc. still to be processed. */
461 #define E1000_TXDCTL_COUNT_DESC 0x00400000
463 /* Flow Control Constants */
464 #define FLOW_CONTROL_ADDRESS_LOW 0x00C28001
465 #define FLOW_CONTROL_ADDRESS_HIGH 0x00000100
466 #define FLOW_CONTROL_TYPE 0x8808
468 /* 802.1q VLAN Packet Size */
469 #define E1000_VLAN_FILTER_TBL_SIZE 128 /* VLAN Filter Table (4096 bits) */
472 * Number of high/low register pairs in the RAR. The RAR (Receive Address
473 * Registers) holds the directed and multicast addresses that we monitor.
474 * Technically, we have 16 spots. However, we reserve one of these spots
475 * (RAR[15]) for our directed address used by controllers with
476 * manageability enabled, allowing us room for 15 multicast addresses.
478 #define E1000_RAR_ENTRIES 15
479 #define E1000_RAH_AV 0x80000000 /* Receive descriptor valid */
480 #define E1000_RAL_MAC_ADDR_LEN 4
481 #define E1000_RAH_MAC_ADDR_LEN 2
484 #define E1000_ERR_NVM 1
485 #define E1000_ERR_PHY 2
486 #define E1000_ERR_CONFIG 3
487 #define E1000_ERR_PARAM 4
488 #define E1000_ERR_MAC_INIT 5
489 #define E1000_ERR_PHY_TYPE 6
490 #define E1000_ERR_RESET 9
491 #define E1000_ERR_MASTER_REQUESTS_PENDING 10
492 #define E1000_ERR_HOST_INTERFACE_COMMAND 11
493 #define E1000_BLK_PHY_RESET 12
494 #define E1000_ERR_SWFW_SYNC 13
495 #define E1000_NOT_IMPLEMENTED 14
496 #define E1000_ERR_INVALID_ARGUMENT 16
497 #define E1000_ERR_NO_SPACE 17
498 #define E1000_ERR_NVM_PBA_SECTION 18
500 /* Loop limit on how long we wait for auto-negotiation to complete */
501 #define FIBER_LINK_UP_LIMIT 50
502 #define COPPER_LINK_UP_LIMIT 10
503 #define PHY_AUTO_NEG_LIMIT 45
504 #define PHY_FORCE_LIMIT 20
505 /* Number of 100 microseconds we wait for PCI Express master disable */
506 #define MASTER_DISABLE_TIMEOUT 800
507 /* Number of milliseconds we wait for PHY configuration done after MAC reset */
508 #define PHY_CFG_TIMEOUT 100
509 /* Number of 2 milliseconds we wait for acquiring MDIO ownership. */
510 #define MDIO_OWNERSHIP_TIMEOUT 10
511 /* Number of milliseconds for NVM auto read done after MAC reset. */
512 #define AUTO_READ_DONE_TIMEOUT 10
515 #define E1000_FCRTH_RTH 0x0000FFF8 /* Mask Bits[15:3] for RTH */
516 #define E1000_FCRTL_RTL 0x0000FFF8 /* Mask Bits[15:3] for RTL */
517 #define E1000_FCRTL_XONE 0x80000000 /* Enable XON frame transmission */
519 /* Transmit Configuration Word */
520 #define E1000_TXCW_FD 0x00000020 /* TXCW full duplex */
521 #define E1000_TXCW_PAUSE 0x00000080 /* TXCW sym pause request */
522 #define E1000_TXCW_ASM_DIR 0x00000100 /* TXCW astm pause direction */
523 #define E1000_TXCW_PAUSE_MASK 0x00000180 /* TXCW pause request mask */
524 #define E1000_TXCW_ANE 0x80000000 /* Auto-neg enable */
526 /* Receive Configuration Word */
527 #define E1000_RXCW_CW 0x0000ffff /* RxConfigWord mask */
528 #define E1000_RXCW_IV 0x08000000 /* Receive config invalid */
529 #define E1000_RXCW_C 0x20000000 /* Receive config */
530 #define E1000_RXCW_SYNCH 0x40000000 /* Receive config synch */
533 #define E1000_TSYNCTXCTL_MAX_ALLOWED_DLY_MASK 0x0000F000 /* max delay */
534 #define E1000_TSYNCTXCTL_SYNC_COMP 0x40000000 /* sync complete */
535 #define E1000_TSYNCTXCTL_START_SYNC 0x80000000 /* initiate sync */
537 #define E1000_TSYNCTXCTL_VALID 0x00000001 /* Tx timestamp valid */
538 #define E1000_TSYNCTXCTL_ENABLED 0x00000010 /* enable Tx timestamping */
540 #define E1000_TSYNCRXCTL_VALID 0x00000001 /* Rx timestamp valid */
541 #define E1000_TSYNCRXCTL_TYPE_MASK 0x0000000E /* Rx type mask */
542 #define E1000_TSYNCRXCTL_TYPE_L2_V2 0x00
543 #define E1000_TSYNCRXCTL_TYPE_L4_V1 0x02
544 #define E1000_TSYNCRXCTL_TYPE_L2_L4_V2 0x04
545 #define E1000_TSYNCRXCTL_TYPE_ALL 0x08
546 #define E1000_TSYNCRXCTL_TYPE_EVENT_V2 0x0A
547 #define E1000_TSYNCRXCTL_ENABLED 0x00000010 /* enable Rx timestamping */
548 #define E1000_TSYNCRXCTL_SYSCFI 0x00000020 /* Sys clock frequency */
550 #define E1000_RXMTRL_PTP_V1_SYNC_MESSAGE 0x00000000
551 #define E1000_RXMTRL_PTP_V1_DELAY_REQ_MESSAGE 0x00010000
553 #define E1000_RXMTRL_PTP_V2_SYNC_MESSAGE 0x00000000
554 #define E1000_RXMTRL_PTP_V2_DELAY_REQ_MESSAGE 0x01000000
556 #define E1000_TIMINCA_INCPERIOD_SHIFT 24
557 #define E1000_TIMINCA_INCVALUE_MASK 0x00FFFFFF
559 /* PCI Express Control */
560 #define E1000_GCR_RXD_NO_SNOOP 0x00000001
561 #define E1000_GCR_RXDSCW_NO_SNOOP 0x00000002
562 #define E1000_GCR_RXDSCR_NO_SNOOP 0x00000004
563 #define E1000_GCR_TXD_NO_SNOOP 0x00000008
564 #define E1000_GCR_TXDSCW_NO_SNOOP 0x00000010
565 #define E1000_GCR_TXDSCR_NO_SNOOP 0x00000020
567 #define PCIE_NO_SNOOP_ALL (E1000_GCR_RXD_NO_SNOOP | \
568 E1000_GCR_RXDSCW_NO_SNOOP | \
569 E1000_GCR_RXDSCR_NO_SNOOP | \
570 E1000_GCR_TXD_NO_SNOOP | \
571 E1000_GCR_TXDSCW_NO_SNOOP | \
572 E1000_GCR_TXDSCR_NO_SNOOP)
575 #define E1000_EECD_SK 0x00000001 /* NVM Clock */
576 #define E1000_EECD_CS 0x00000002 /* NVM Chip Select */
577 #define E1000_EECD_DI 0x00000004 /* NVM Data In */
578 #define E1000_EECD_DO 0x00000008 /* NVM Data Out */
579 #define E1000_EECD_REQ 0x00000040 /* NVM Access Request */
580 #define E1000_EECD_GNT 0x00000080 /* NVM Access Grant */
581 #define E1000_EECD_PRES 0x00000100 /* NVM Present */
582 #define E1000_EECD_SIZE 0x00000200 /* NVM Size (0=64 word 1=256 word) */
583 /* NVM Addressing bits based on type (0-small, 1-large) */
584 #define E1000_EECD_ADDR_BITS 0x00000400
585 #define E1000_NVM_GRANT_ATTEMPTS 1000 /* NVM # attempts to gain grant */
586 #define E1000_EECD_AUTO_RD 0x00000200 /* NVM Auto Read done */
587 #define E1000_EECD_SIZE_EX_MASK 0x00007800 /* NVM Size */
588 #define E1000_EECD_SIZE_EX_SHIFT 11
589 #define E1000_EECD_FLUPD 0x00080000 /* Update FLASH */
590 #define E1000_EECD_AUPDEN 0x00100000 /* Enable Autonomous FLASH update */
591 #define E1000_EECD_SEC1VAL 0x00400000 /* Sector One Valid */
592 #define E1000_EECD_SEC1VAL_VALID_MASK (E1000_EECD_AUTO_RD | E1000_EECD_PRES)
594 #define E1000_NVM_RW_REG_DATA 16 /* Offset to data in NVM r/w regs */
595 #define E1000_NVM_RW_REG_DONE 2 /* Offset to READ/WRITE done bit */
596 #define E1000_NVM_RW_REG_START 1 /* Start operation */
597 #define E1000_NVM_RW_ADDR_SHIFT 2 /* Shift to the address bits */
598 #define E1000_NVM_POLL_WRITE 1 /* Flag for polling write complete */
599 #define E1000_NVM_POLL_READ 0 /* Flag for polling read complete */
600 #define E1000_FLASH_UPDATES 2000
602 /* NVM Word Offsets */
603 #define NVM_COMPAT 0x0003
604 #define NVM_ID_LED_SETTINGS 0x0004
605 #define NVM_FUTURE_INIT_WORD1 0x0019
606 #define NVM_COMPAT_VALID_CSUM 0x0001
607 #define NVM_FUTURE_INIT_WORD1_VALID_CSUM 0x0040
609 #define NVM_INIT_CONTROL2_REG 0x000F
610 #define NVM_INIT_CONTROL3_PORT_B 0x0014
611 #define NVM_INIT_3GIO_3 0x001A
612 #define NVM_INIT_CONTROL3_PORT_A 0x0024
613 #define NVM_CFG 0x0012
614 #define NVM_ALT_MAC_ADDR_PTR 0x0037
615 #define NVM_CHECKSUM_REG 0x003F
617 #define E1000_NVM_CFG_DONE_PORT_0 0x40000 /* MNG config cycle done */
618 #define E1000_NVM_CFG_DONE_PORT_1 0x80000 /* ...for second port */
620 /* Mask bits for fields in Word 0x0f of the NVM */
621 #define NVM_WORD0F_PAUSE_MASK 0x3000
622 #define NVM_WORD0F_PAUSE 0x1000
623 #define NVM_WORD0F_ASM_DIR 0x2000
625 /* Mask bits for fields in Word 0x1a of the NVM */
626 #define NVM_WORD1A_ASPM_MASK 0x000C
628 /* Mask bits for fields in Word 0x03 of the EEPROM */
629 #define NVM_COMPAT_LOM 0x0800
631 /* length of string needed to store PBA number */
632 #define E1000_PBANUM_LENGTH 11
634 /* For checksumming, the sum of all words in the NVM should equal 0xBABA. */
635 #define NVM_SUM 0xBABA
637 /* PBA (printed board assembly) number words */
638 #define NVM_PBA_OFFSET_0 8
639 #define NVM_PBA_OFFSET_1 9
640 #define NVM_PBA_PTR_GUARD 0xFAFA
641 #define NVM_WORD_SIZE_BASE_SHIFT 6
643 /* NVM Commands - SPI */
644 #define NVM_MAX_RETRY_SPI 5000 /* Max wait of 5ms, for RDY signal */
645 #define NVM_READ_OPCODE_SPI 0x03 /* NVM read opcode */
646 #define NVM_WRITE_OPCODE_SPI 0x02 /* NVM write opcode */
647 #define NVM_A8_OPCODE_SPI 0x08 /* opcode bit-3 = address bit-8 */
648 #define NVM_WREN_OPCODE_SPI 0x06 /* NVM set Write Enable latch */
649 #define NVM_RDSR_OPCODE_SPI 0x05 /* NVM read Status register */
651 /* SPI NVM Status Register */
652 #define NVM_STATUS_RDY_SPI 0x01
654 /* Word definitions for ID LED Settings */
655 #define ID_LED_RESERVED_0000 0x0000
656 #define ID_LED_RESERVED_FFFF 0xFFFF
657 #define ID_LED_DEFAULT ((ID_LED_OFF1_ON2 << 12) | \
658 (ID_LED_OFF1_OFF2 << 8) | \
659 (ID_LED_DEF1_DEF2 << 4) | \
661 #define ID_LED_DEF1_DEF2 0x1
662 #define ID_LED_DEF1_ON2 0x2
663 #define ID_LED_DEF1_OFF2 0x3
664 #define ID_LED_ON1_DEF2 0x4
665 #define ID_LED_ON1_ON2 0x5
666 #define ID_LED_ON1_OFF2 0x6
667 #define ID_LED_OFF1_DEF2 0x7
668 #define ID_LED_OFF1_ON2 0x8
669 #define ID_LED_OFF1_OFF2 0x9
671 #define IGP_ACTIVITY_LED_MASK 0xFFFFF0FF
672 #define IGP_ACTIVITY_LED_ENABLE 0x0300
673 #define IGP_LED3_MODE 0x07000000
675 /* PCI/PCI-X/PCI-EX Config space */
676 #define PCI_HEADER_TYPE_REGISTER 0x0E
677 #define PCIE_LINK_STATUS 0x12
679 #define PCI_HEADER_TYPE_MULTIFUNC 0x80
680 #define PCIE_LINK_WIDTH_MASK 0x3F0
681 #define PCIE_LINK_WIDTH_SHIFT 4
683 #define PHY_REVISION_MASK 0xFFFFFFF0
684 #define MAX_PHY_REG_ADDRESS 0x1F /* 5 bit address bus (0-0x1F) */
685 #define MAX_PHY_MULTI_PAGE_REG 0xF
687 /* Bit definitions for valid PHY IDs.
691 #define M88E1000_E_PHY_ID 0x01410C50
692 #define M88E1000_I_PHY_ID 0x01410C30
693 #define M88E1011_I_PHY_ID 0x01410C20
694 #define IGP01E1000_I_PHY_ID 0x02A80380
695 #define M88E1111_I_PHY_ID 0x01410CC0
696 #define GG82563_E_PHY_ID 0x01410CA0
697 #define IGP03E1000_E_PHY_ID 0x02A80390
698 #define IFE_E_PHY_ID 0x02A80330
699 #define IFE_PLUS_E_PHY_ID 0x02A80320
700 #define IFE_C_E_PHY_ID 0x02A80310
701 #define BME1000_E_PHY_ID 0x01410CB0
702 #define BME1000_E_PHY_ID_R2 0x01410CB1
703 #define I82577_E_PHY_ID 0x01540050
704 #define I82578_E_PHY_ID 0x004DD040
705 #define I82579_E_PHY_ID 0x01540090
706 #define I217_E_PHY_ID 0x015400A0
708 /* M88E1000 Specific Registers */
709 #define M88E1000_PHY_SPEC_CTRL 0x10 /* PHY Specific Control Register */
710 #define M88E1000_PHY_SPEC_STATUS 0x11 /* PHY Specific Status Register */
711 #define M88E1000_EXT_PHY_SPEC_CTRL 0x14 /* Extended PHY Specific Control */
713 #define M88E1000_PHY_PAGE_SELECT 0x1D /* Reg 29 for page number setting */
714 #define M88E1000_PHY_GEN_CONTROL 0x1E /* Its meaning depends on reg 29 */
716 /* M88E1000 PHY Specific Control Register */
717 #define M88E1000_PSCR_POLARITY_REVERSAL 0x0002 /* 1=Polarity Reversal enabled */
718 #define M88E1000_PSCR_MDI_MANUAL_MODE 0x0000 /* MDI Crossover Mode bits 6:5 */
719 /* Manual MDI configuration */
720 #define M88E1000_PSCR_MDIX_MANUAL_MODE 0x0020 /* Manual MDIX configuration */
721 /* 1000BASE-T: Auto crossover, 100BASE-TX/10BASE-T: MDI Mode */
722 #define M88E1000_PSCR_AUTO_X_1000T 0x0040
723 /* Auto crossover enabled all speeds */
724 #define M88E1000_PSCR_AUTO_X_MODE 0x0060
725 #define M88E1000_PSCR_ASSERT_CRS_ON_TX 0x0800 /* 1=Assert CRS on Transmit */
727 /* M88E1000 PHY Specific Status Register */
728 #define M88E1000_PSSR_REV_POLARITY 0x0002 /* 1=Polarity reversed */
729 #define M88E1000_PSSR_DOWNSHIFT 0x0020 /* 1=Downshifted */
730 #define M88E1000_PSSR_MDIX 0x0040 /* 1=MDIX; 0=MDI */
731 /* 0=<50M; 1=50-80M; 2=80-110M; 3=110-140M; 4=>140M */
732 #define M88E1000_PSSR_CABLE_LENGTH 0x0380
733 #define M88E1000_PSSR_SPEED 0xC000 /* Speed, bits 14:15 */
734 #define M88E1000_PSSR_1000MBS 0x8000 /* 10=1000Mbs */
736 #define M88E1000_PSSR_CABLE_LENGTH_SHIFT 7
738 /* Number of times we will attempt to autonegotiate before downshifting if we
741 #define M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK 0x0C00
742 #define M88E1000_EPSCR_MASTER_DOWNSHIFT_1X 0x0000
743 /* Number of times we will attempt to autonegotiate before downshifting if we
746 #define M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK 0x0300
747 #define M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X 0x0100
748 #define M88E1000_EPSCR_TX_CLK_25 0x0070 /* 25 MHz TX_CLK */
750 /* M88EC018 Rev 2 specific DownShift settings */
751 #define M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK 0x0E00
752 #define M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X 0x0800
754 #define I82578_EPSCR_DOWNSHIFT_ENABLE 0x0020
755 #define I82578_EPSCR_DOWNSHIFT_COUNTER_MASK 0x001C
757 /* BME1000 PHY Specific Control Register */
758 #define BME1000_PSCR_ENABLE_DOWNSHIFT 0x0800 /* 1 = enable downshift */
762 * 4-0: register offset
764 #define GG82563_PAGE_SHIFT 5
765 #define GG82563_REG(page, reg) \
766 (((page) << GG82563_PAGE_SHIFT) | ((reg) & MAX_PHY_REG_ADDRESS))
767 #define GG82563_MIN_ALT_REG 30
769 /* GG82563 Specific Registers */
770 #define GG82563_PHY_SPEC_CTRL \
771 GG82563_REG(0, 16) /* PHY Specific Control */
772 #define GG82563_PHY_PAGE_SELECT \
773 GG82563_REG(0, 22) /* Page Select */
774 #define GG82563_PHY_SPEC_CTRL_2 \
775 GG82563_REG(0, 26) /* PHY Specific Control 2 */
776 #define GG82563_PHY_PAGE_SELECT_ALT \
777 GG82563_REG(0, 29) /* Alternate Page Select */
779 #define GG82563_PHY_MAC_SPEC_CTRL \
780 GG82563_REG(2, 21) /* MAC Specific Control Register */
782 #define GG82563_PHY_DSP_DISTANCE \
783 GG82563_REG(5, 26) /* DSP Distance */
785 /* Page 193 - Port Control Registers */
786 #define GG82563_PHY_KMRN_MODE_CTRL \
787 GG82563_REG(193, 16) /* Kumeran Mode Control */
788 #define GG82563_PHY_PWR_MGMT_CTRL \
789 GG82563_REG(193, 20) /* Power Management Control */
791 /* Page 194 - KMRN Registers */
792 #define GG82563_PHY_INBAND_CTRL \
793 GG82563_REG(194, 18) /* Inband Control */
796 #define E1000_MDIC_REG_MASK 0x001F0000
797 #define E1000_MDIC_REG_SHIFT 16
798 #define E1000_MDIC_PHY_SHIFT 21
799 #define E1000_MDIC_OP_WRITE 0x04000000
800 #define E1000_MDIC_OP_READ 0x08000000
801 #define E1000_MDIC_READY 0x10000000
802 #define E1000_MDIC_ERROR 0x40000000
805 #define E1000_GEN_POLL_TIMEOUT 640
807 #endif /* _E1000_DEFINES_H_ */
projects / mirror_ubuntu-eoan-kernel.git / blob