drivers/net/hamradio/Kconfig

   1 # SPDX-License-Identifier: GPL-2.0-only
   2 config MKISS
   3         tristate "Serial port KISS driver"
   4         depends on AX25 && TTY
   5         select CRC16
   6         ---help---
   7           KISS is a protocol used for the exchange of data between a computer
   8           and a Terminal Node Controller (a small embedded system commonly
   9           used for networking over AX.25 amateur radio connections; it
  10           connects the computer's serial port with the radio's microphone
  11           input and speaker output).
  12
  13           Although KISS is less advanced than the 6pack protocol, it has
  14           the advantage that it is already supported by most modern TNCs
  15           without the need for a firmware upgrade.
  16
  17           To compile this driver as a module, choose M here: the module
  18           will be called mkiss.
  19
  20 config 6PACK
  21         tristate "Serial port 6PACK driver"
  22         depends on AX25 && TTY
  23         ---help---
  24           6pack is a transmission protocol for the data exchange between your
  25           PC and your TNC (the Terminal Node Controller acts as a kind of
  26           modem connecting your computer's serial port to your radio's
  27           microphone input and speaker output). This protocol can be used as
  28           an alternative to KISS for networking over AX.25 amateur radio
  29           connections, but it has some extended functionality.
  30
  31           Note that this driver is still experimental and might cause
  32           problems. For details about the features and the usage of the
  33           driver, read <file:Documentation/networking/6pack.txt>.
  34
  35           To compile this driver as a module, choose M here: the module
  36           will be called 6pack.
  37
  38 config BPQETHER
  39         tristate "BPQ Ethernet driver"
  40         depends on AX25
  41         help
  42           AX.25 is the protocol used for computer communication over amateur
  43           radio. If you say Y here, you will be able to send and receive AX.25
  44           traffic over Ethernet (also called "BPQ AX.25"), which could be
  45           useful if some other computer on your local network has a direct
  46           amateur radio connection.
  47
  48 config DMASCC
  49         tristate "High-speed (DMA) SCC driver for AX.25"
  50         depends on ISA && AX25 && BROKEN_ON_SMP && ISA_DMA_API
  51         ---help---
  52           This is a driver for high-speed SCC boards, i.e. those supporting
  53           DMA on one port. You usually use those boards to connect your
  54           computer to an amateur radio modem (such as the WA4DSY 56kbps
  55           modem), in order to send and receive AX.25 packet radio network
  56           traffic.
  57
  58           Currently, this driver supports Ottawa PI/PI2, Paccomm/Gracilis
  59           PackeTwin, and S5SCC/DMA boards. They are detected automatically.
  60           If you have one of these cards, say Y here and read the AX25-HOWTO,
  61           available from <http://www.tldp.org/docs.html#howto>.
  62
  63           This driver can operate multiple boards simultaneously. If you
  64           compile it as a module (by saying M instead of Y), it will be called
  65           dmascc. If you don't pass any parameter to the driver, all
  66           possible I/O addresses are probed. This could irritate other devices
  67           that are currently not in use. You may specify the list of addresses
  68           to be probed by "dmascc.io=addr1,addr2,..." (when compiled into the
  69           kernel image) or "io=addr1,addr2,..." (when loaded as a module). The
  70           network interfaces will be called dmascc0 and dmascc1 for the board
  71           detected first, dmascc2 and dmascc3 for the second one, and so on.
  72
  73           Before you configure each interface with ifconfig, you MUST set
  74           certain parameters, such as channel access timing, clock mode, and
  75           DMA channel. This is accomplished with a small utility program,
  76           dmascc_cfg, available at
  77           <http://www.linux-ax25.org/wiki/Ax25-tools>. Please be sure to
  78           get at least version 1.27 of dmascc_cfg, as older versions will not
  79           work with the current driver.
  80
  81 config SCC
  82         tristate "Z8530 SCC driver"
  83         depends on ISA && AX25 && ISA_DMA_API
  84         ---help---
  85           These cards are used to connect your Linux box to an amateur radio
  86           in order to communicate with other computers. If you want to use
  87           this, read <file:Documentation/networking/z8530drv.txt> and the
  88           AX25-HOWTO, available from
  89           <http://www.tldp.org/docs.html#howto>. Also make sure to say Y
  90           to "Amateur Radio AX.25 Level 2" support.
  91
  92           To compile this driver as a module, choose M here: the module
  93           will be called scc.
  94
  95 config SCC_DELAY
  96         bool "additional delay for PA0HZP OptoSCC compatible boards"
  97         depends on SCC
  98         help
  99           Say Y here if you experience problems with the SCC driver not
 100           working properly; please read
 101           <file:Documentation/networking/z8530drv.txt> for details.
 102
 103           If unsure, say N.
 104
 105 config SCC_TRXECHO
 106         bool "support for TRX that feedback the tx signal to rx"
 107         depends on SCC
 108         help
 109           Some transmitters feed the transmitted signal back to the receive
 110           line.  Say Y here to foil this by explicitly disabling the receiver
 111           during data transmission.
 112
 113           If in doubt, say Y.
 114
 115 config BAYCOM_SER_FDX
 116         tristate "BAYCOM ser12 fullduplex driver for AX.25"
 117         depends on AX25 && !S390
 118         select CRC_CCITT
 119         ---help---
 120           This is one of two drivers for Baycom style simple amateur radio
 121           modems that connect to a serial interface. The driver supports the
 122           ser12 design in full-duplex mode. In addition, it allows the
 123           baudrate to be set between 300 and 4800 baud (however not all modems
 124           support all baudrates). This is the preferred driver. The next
 125           driver, "BAYCOM ser12 half-duplex driver for AX.25" is the old
 126           driver and still provided in case this driver does not work with
 127           your serial interface chip. To configure the driver, use the sethdlc
 128           utility available in the standard ax25 utilities package. For
 129           information on the modems, see <http://www.baycom.de/> and
 130           <file:Documentation/networking/baycom.txt>.
 131
 132           To compile this driver as a module, choose M here: the module
 133           will be called baycom_ser_fdx.  This is recommended.
 134
 135 config BAYCOM_SER_HDX
 136         tristate "BAYCOM ser12 halfduplex driver for AX.25"
 137         depends on AX25 && !S390
 138         select CRC_CCITT
 139         ---help---
 140           This is one of two drivers for Baycom style simple amateur radio
 141           modems that connect to a serial interface. The driver supports the
 142           ser12 design in half-duplex mode. This is the old driver.  It is
 143           still provided in case your serial interface chip does not work with
 144           the full-duplex driver. This driver is deprecated.  To configure
 145           the driver, use the sethdlc utility available in the standard ax25
 146           utilities package. For information on the modems, see
 147           <http://www.baycom.de/> and
 148           <file:Documentation/networking/baycom.txt>.
 149
 150           To compile this driver as a module, choose M here: the module
 151           will be called baycom_ser_hdx.  This is recommended.
 152
 153 config BAYCOM_PAR
 154         tristate "BAYCOM picpar and par96 driver for AX.25"
 155         depends on PARPORT && AX25
 156         select CRC_CCITT
 157         ---help---
 158           This is a driver for Baycom style simple amateur radio modems that
 159           connect to a parallel interface. The driver supports the picpar and
 160           par96 designs. To configure the driver, use the sethdlc utility
 161           available in the standard ax25 utilities package. For information on
 162           the modems, see <http://www.baycom.de/> and the file
 163           <file:Documentation/networking/baycom.txt>.
 164
 165           To compile this driver as a module, choose M here: the module
 166           will be called baycom_par.  This is recommended.
 167
 168 config BAYCOM_EPP
 169         tristate "BAYCOM epp driver for AX.25"
 170         depends on PARPORT && AX25 && !64BIT
 171         select CRC_CCITT
 172         ---help---
 173           This is a driver for Baycom style simple amateur radio modems that
 174           connect to a parallel interface. The driver supports the EPP
 175           designs. To configure the driver, use the sethdlc utility available
 176           in the standard ax25 utilities package. For information on the
 177           modems, see <http://www.baycom.de/> and the file
 178           <file:Documentation/networking/baycom.txt>.
 179
 180           To compile this driver as a module, choose M here: the module
 181           will be called baycom_epp.  This is recommended.
 182
 183 config YAM
 184         tristate "YAM driver for AX.25"
 185         depends on AX25 && !S390
 186         help
 187           The YAM is a modem for packet radio which connects to the serial
 188           port and includes some of the functions of a Terminal Node
 189           Controller. If you have one of those, say Y here.
 190
 191           To compile this driver as a module, choose M here: the module
 192           will be called yam.
 193
 194