drivers/net/phy/Kconfig

   1 #
   2 # PHY Layer Configuration
   3 #
   4
   5 menuconfig MDIO_DEVICE
   6         tristate "MDIO bus device drivers"
   7         help
   8            MDIO devices and driver infrastructure code.
   9
  10 if MDIO_DEVICE
  11
  12 config MDIO_BCM_IPROC
  13         tristate "Broadcom iProc MDIO bus controller"
  14         depends on ARCH_BCM_IPROC || COMPILE_TEST
  15         depends on HAS_IOMEM && OF_MDIO
  16         help
  17           This module provides a driver for the MDIO busses found in the
  18           Broadcom iProc SoC's.
  19
  20 config MDIO_BCM_UNIMAC
  21         tristate "Broadcom UniMAC MDIO bus controller"
  22         depends on HAS_IOMEM && OF_MDIO
  23         help
  24           This module provides a driver for the Broadcom UniMAC MDIO busses.
  25           This hardware can be found in the Broadcom GENET Ethernet MAC
  26           controllers as well as some Broadcom Ethernet switches such as the
  27           Starfighter 2 switches.
  28
  29 config MDIO_BITBANG
  30         tristate "Bitbanged MDIO buses"
  31         depends on !(MDIO_DEVICE=y && PHYLIB=m)
  32         help
  33           This module implements the MDIO bus protocol in software,
  34           for use by low level drivers that export the ability to
  35           drive the relevant pins.
  36
  37           If in doubt, say N.
  38
  39 config MDIO_BUS_MUX
  40         tristate
  41         depends on OF_MDIO
  42         help
  43           This module provides a driver framework for MDIO bus
  44           multiplexers which connect one of several child MDIO busses
  45           to a parent bus.  Switching between child busses is done by
  46           device specific drivers.
  47
  48 config MDIO_BUS_MUX_BCM_IPROC
  49         tristate "Broadcom iProc based MDIO bus multiplexers"
  50         depends on OF && OF_MDIO && (ARCH_BCM_IPROC || COMPILE_TEST)
  51         select MDIO_BUS_MUX
  52         default ARCH_BCM_IPROC
  53         help
  54           This module provides a driver for MDIO bus multiplexers found in
  55           iProc based Broadcom SoCs. This multiplexer connects one of several
  56           child MDIO bus to a parent bus. Buses could be internal as well as
  57           external and selection logic lies inside the same multiplexer.
  58
  59 config MDIO_BUS_MUX_GPIO
  60         tristate "GPIO controlled MDIO bus multiplexers"
  61         depends on OF_GPIO && OF_MDIO
  62         select MDIO_BUS_MUX
  63         help
  64           This module provides a driver for MDIO bus multiplexers that
  65           are controlled via GPIO lines.  The multiplexer connects one of
  66           several child MDIO busses to a parent bus.  Child bus
  67           selection is under the control of GPIO lines.
  68
  69 config MDIO_BUS_MUX_MMIOREG
  70         tristate "MMIO device-controlled MDIO bus multiplexers"
  71         depends on OF_MDIO && HAS_IOMEM
  72         select MDIO_BUS_MUX
  73         help
  74           This module provides a driver for MDIO bus multiplexers that
  75           are controlled via a simple memory-mapped device, like an FPGA.
  76           The multiplexer connects one of several child MDIO busses to a
  77           parent bus.  Child bus selection is under the control of one of
  78           the FPGA's registers.
  79
  80           Currently, only 8-bit registers are supported.
  81
  82 config MDIO_CAVIUM
  83         tristate
  84
  85 config MDIO_GPIO
  86         tristate "GPIO lib-based bitbanged MDIO buses"
  87         depends on MDIO_BITBANG && GPIOLIB
  88         ---help---
  89           Supports GPIO lib-based MDIO busses.
  90
  91           To compile this driver as a module, choose M here: the module
  92           will be called mdio-gpio.
  93
  94 config MDIO_HISI_FEMAC
  95         tristate "Hisilicon FEMAC MDIO bus controller"
  96         depends on HAS_IOMEM && OF_MDIO
  97         help
  98           This module provides a driver for the MDIO busses found in the
  99           Hisilicon SoC that have an Fast Ethernet MAC.
 100
 101 config MDIO_MOXART
 102         tristate "MOXA ART MDIO interface support"
 103         depends on ARCH_MOXART
 104         help
 105           This driver supports the MDIO interface found in the network
 106           interface units of the MOXA ART SoC
 107
 108 config MDIO_OCTEON
 109         tristate "Octeon and some ThunderX SOCs MDIO buses"
 110         depends on 64BIT
 111         depends on HAS_IOMEM
 112         select MDIO_CAVIUM
 113         help
 114           This module provides a driver for the Octeon and ThunderX MDIO
 115           buses. It is required by the Octeon and ThunderX ethernet device
 116           drivers on some systems.
 117
 118 config MDIO_SUN4I
 119         tristate "Allwinner sun4i MDIO interface support"
 120         depends on ARCH_SUNXI
 121         help
 122           This driver supports the MDIO interface found in the network
 123           interface units of the Allwinner SoC that have an EMAC (A10,
 124           A12, A10s, etc.)
 125
 126 config MDIO_THUNDER
 127         tristate "ThunderX SOCs MDIO buses"
 128         depends on 64BIT
 129         depends on PCI
 130         select MDIO_CAVIUM
 131         help
 132           This driver supports the MDIO interfaces found on Cavium
 133           ThunderX SoCs when the MDIO bus device appears as a PCI
 134           device.
 135
 136 config MDIO_XGENE
 137         tristate "APM X-Gene SoC MDIO bus controller"
 138         depends on ARCH_XGENE || COMPILE_TEST
 139         help
 140           This module provides a driver for the MDIO busses found in the
 141           APM X-Gene SoC's.
 142
 143 endif
 144
 145 menuconfig PHYLIB
 146         tristate "PHY Device support and infrastructure"
 147         depends on NETDEVICES
 148         select MDIO_DEVICE
 149         help
 150           Ethernet controllers are usually attached to PHY
 151           devices.  This option provides infrastructure for
 152           managing PHY devices.
 153
 154 if PHYLIB
 155
 156 config SWPHY
 157         bool
 158
 159 config LED_TRIGGER_PHY
 160         bool "Support LED triggers for tracking link state"
 161         depends on LEDS_TRIGGERS
 162         ---help---
 163           Adds support for a set of LED trigger events per-PHY.  Link
 164           state change will trigger the events, for consumption by an
 165           LED class driver.  There are triggers for each link speed currently
 166           supported by the phy, and are of the form:
 167                <mii bus id>:<phy>:<speed>
 168
 169           Where speed is in the form:
 170                 <Speed in megabits>Mbps or <Speed in gigabits>Gbps
 171
 172
 173 comment "MII PHY device drivers"
 174
 175 config AMD_PHY
 176         tristate "AMD PHYs"
 177         ---help---
 178           Currently supports the am79c874
 179
 180 config AQUANTIA_PHY
 181         tristate "Aquantia PHYs"
 182         ---help---
 183           Currently supports the Aquantia AQ1202, AQ2104, AQR105, AQR405
 184
 185 config AT803X_PHY
 186         tristate "AT803X PHYs"
 187         ---help---
 188           Currently supports the AT8030 and AT8035 model
 189
 190 config BCM63XX_PHY
 191         tristate "Broadcom 63xx SOCs internal PHY"
 192         depends on BCM63XX
 193         select BCM_NET_PHYLIB
 194         ---help---
 195           Currently supports the 6348 and 6358 PHYs.
 196
 197 config BCM7XXX_PHY
 198         tristate "Broadcom 7xxx SOCs internal PHYs"
 199         select BCM_NET_PHYLIB
 200         ---help---
 201           Currently supports the BCM7366, BCM7439, BCM7445, and
 202           40nm and 65nm generation of BCM7xxx Set Top Box SoCs.
 203
 204 config BCM87XX_PHY
 205         tristate "Broadcom BCM8706 and BCM8727 PHYs"
 206         help
 207           Currently supports the BCM8706 and BCM8727 10G Ethernet PHYs.
 208
 209 config BCM_CYGNUS_PHY
 210         tristate "Broadcom Cygnus SoC internal PHY"
 211         depends on ARCH_BCM_CYGNUS || COMPILE_TEST
 212         depends on MDIO_BCM_IPROC
 213         select BCM_NET_PHYLIB
 214         ---help---
 215           This PHY driver is for the 1G internal PHYs of the Broadcom
 216           Cygnus Family SoC.
 217
 218           Currently supports internal PHY's used in the BCM11300,
 219           BCM11320, BCM11350, BCM11360, BCM58300, BCM58302,
 220           BCM58303 & BCM58305 Broadcom Cygnus SoCs.
 221
 222 config BCM_NET_PHYLIB
 223         tristate
 224
 225 config BROADCOM_PHY
 226         tristate "Broadcom PHYs"
 227         select BCM_NET_PHYLIB
 228         ---help---
 229           Currently supports the BCM5411, BCM5421, BCM5461, BCM54616S, BCM5464,
 230           BCM5481, BCM54810 and BCM5482 PHYs.
 231
 232 config CICADA_PHY
 233         tristate "Cicada PHYs"
 234         ---help---
 235           Currently supports the cis8204
 236
 237 config DAVICOM_PHY
 238         tristate "Davicom PHYs"
 239         ---help---
 240           Currently supports dm9161e and dm9131
 241
 242 config DP83848_PHY
 243         tristate "Texas Instruments DP83848 PHY"
 244         ---help---
 245           Supports the DP83848 PHY.
 246
 247 config DP83867_PHY
 248         tristate "Texas Instruments DP83867 Gigabit PHY"
 249         ---help---
 250           Currently supports the DP83867 PHY.
 251
 252 config FIXED_PHY
 253         tristate "MDIO Bus/PHY emulation with fixed speed/link PHYs"
 254         depends on PHYLIB
 255         select SWPHY
 256         ---help---
 257           Adds the platform "fixed" MDIO Bus to cover the boards that use
 258           PHYs that are not connected to the real MDIO bus.
 259
 260           Currently tested with mpc866ads and mpc8349e-mitx.
 261
 262 config ICPLUS_PHY
 263         tristate "ICPlus PHYs"
 264         ---help---
 265           Currently supports the IP175C and IP1001 PHYs.
 266
 267 config INTEL_XWAY_PHY
 268         tristate "Intel XWAY PHYs"
 269         ---help---
 270           Supports the Intel XWAY (former Lantiq) 11G and 22E PHYs.
 271           These PHYs are marked as standalone chips under the names
 272           PEF 7061, PEF 7071 and PEF 7072 or integrated into the Intel
 273           SoCs xRX200, xRX300, xRX330, xRX350 and xRX550.
 274
 275 config LSI_ET1011C_PHY
 276         tristate "LSI ET1011C PHY"
 277         ---help---
 278           Supports the LSI ET1011C PHY.
 279
 280 config LXT_PHY
 281         tristate "Intel LXT PHYs"
 282         ---help---
 283           Currently supports the lxt970, lxt971
 284
 285 config MARVELL_PHY
 286         tristate "Marvell PHYs"
 287         ---help---
 288           Currently has a driver for the 88E1011S
 289
 290 config MESON_GXL_PHY
 291         tristate "Amlogic Meson GXL Internal PHY"
 292         depends on ARCH_MESON || COMPILE_TEST
 293         ---help---
 294           Currently has a driver for the Amlogic Meson GXL Internal PHY
 295
 296 config MICREL_PHY
 297         tristate "Micrel PHYs"
 298         ---help---
 299           Supports the KSZ9021, VSC8201, KS8001 PHYs.
 300
 301 config MICROCHIP_PHY
 302         tristate "Microchip PHYs"
 303         help
 304           Supports the LAN88XX PHYs.
 305
 306 config MICROSEMI_PHY
 307         tristate "Microsemi PHYs"
 308         ---help---
 309           Currently supports VSC8530, VSC8531, VSC8540 and VSC8541 PHYs
 310
 311 config NATIONAL_PHY
 312         tristate "National Semiconductor PHYs"
 313         ---help---
 314           Currently supports the DP83865 PHY.
 315
 316 config QSEMI_PHY
 317         tristate "Quality Semiconductor PHYs"
 318         ---help---
 319           Currently supports the qs6612
 320
 321 config REALTEK_PHY
 322         tristate "Realtek PHYs"
 323         ---help---
 324           Supports the Realtek 821x PHY.
 325
 326 config SMSC_PHY
 327         tristate "SMSC PHYs"
 328         ---help---
 329           Currently supports the LAN83C185, LAN8187 and LAN8700 PHYs
 330
 331 config STE10XP
 332         tristate "STMicroelectronics STe10Xp PHYs"
 333         ---help---
 334           This is the driver for the STe100p and STe101p PHYs.
 335
 336 config TERANETICS_PHY
 337         tristate "Teranetics PHYs"
 338         ---help---
 339           Currently supports the Teranetics TN2020
 340
 341 config VITESSE_PHY
 342         tristate "Vitesse PHYs"
 343         ---help---
 344           Currently supports the vsc8244
 345
 346 config XILINX_GMII2RGMII
 347        tristate "Xilinx GMII2RGMII converter driver"
 348        ---help---
 349          This driver support xilinx GMII to RGMII IP core it provides
 350          the Reduced Gigabit Media Independent Interface(RGMII) between
 351          Ethernet physical media devices and the Gigabit Ethernet controller.
 352
 353 endif # PHYLIB
 354
 355 config MICREL_KS8995MA
 356         tristate "Micrel KS8995MA 5-ports 10/100 managed Ethernet switch"
 357         depends on SPI